Search Documents

By S. Mathieu, R. Mennillod-Blondin, P. Cousin, N. Valle, H. Bouzahzah, P. Marion

The gold deposit of the Lapa mine has a complex mineralogical gold state with coarse and fine native gold, aurostibite and submicroscopic gold within arsenopyrite. A specific mineralogical characterization of the refractory fraction was conducted combining various techniques such as optical microscopy, electron microscopy, electron microprobe and secondary ion mass spectrometry. In parallel, the mineral processing behaviour and the recovery of the refractory gold were studied by pressure oxidation and cyanide leaching. This paper presents the mineralogical methodology developed to characterize the refractory gold distribution within arsenopyrite. These results are presented and interpreted in order to plot gold recovery versus sulphide oxidation. The comparison of the metallurgical behaviour yields predicted from the mineralogical data and the one calculated from leaching tests shows a good agreement and allows mineralogical explanations of the gold metallurgical behaviour.

Jan 1, 2011

By W. A. Bain

"AbstractProduction from the Excelsior Reservoir has amounted to approximately one million barrels. This production has caused a 'Pressure •drop of 10 p.s.i. from the original pressure of 1,245 p.s.i.g. Volumetric balance calculations indicate that the pool as being produced by a water drive whose strength is •probably unsurpassed in Western Canada. It has also been shown by 'unsteady state' calculations that the reservoir will still be above the saturation pressure of 915 p.s.i.g. at the time of depletion. The average permeability of the producing formation is approximately 1,000 millidarcys and, consequently, well draw-downs are very low. The field is essentially a bottom-water drive and calculations have shown that gravity drainage will greatly assist the recovery of oil. Water flooding data on several cores •have placed the flushing efficiency at •approximately 50 per cent, which indicates a recoverable oil-in-place of 17.7 million stock tank barrels. Calculations and field data indicate that the MER for the early life of this field is probably as high as 8,000 to 10,000 stock tank barrels per day.IntroductionTHE EXCELSIOR NISKU oil reservoir is located about twenty miles northeast of Edmonton. The field was discovered in November, 1949, by Imperial Excelsior N.o.1 well, in Lsd. 13, Sec. 3, Twp. 56, R. 22, W. 4, at a depth of 3,850 feet.Since discovery, development has continued on a 40~acre spacing pattern. At the end of 1951, drilling over approximately 80 per cent of the estimated productive area of 1,680 acres had established 32 we1ls capable •of production. The field •has been fairly well delineated by dry holes on all but the eastern flank ."

Jan 1, 1952

By Renliang Shan

Site conditions of China?s coal roadways are complex and changeable, and scientific classification of them is the fundamental basis for coal roadway support design, with great significance for ensuring proper roadway service. Upon analysis of the issues, a commentary regarding the research progress on classification of the stability of rocks surrounding coal roadways in China has been achieved from the point of view of classification methods and indexes. The shortcomings and applicable scope of rock stability classification methods related to coal roadways have been analyzed. It has been asserted that combining artificial neural networks with fuzzy mathematics, combining fuzzy mathematics with grey theory, applying new avenues such as support vector machine algorithms or unascertained average classification, and making classification indexes more scientific are future directions for development of rock stability classification for coal roadways.

Aug 1, 2013

By R. Fukuzawa

"The objective of this research is to evaluate the magnitude of carbon prices required to drive process development and innovation for the global nickel industry in a direction that tackles the multifaceted sustainability challenges that the industry faces, including air pollution reduction and greenhouse gas abatement. The results suggest that the currently considered carbon prices are not sufficient to drive innovations in processing methods or upstream pollution prevention. The co-benefits of climate change mitigation and pollution prevention cannot be readily realized under climate change policy alone. Increased coordination between climate change policy and performance-based environmental legislation is necessary. INTRODUCTIONNickel is an important metal in our modern society as it is used in stainless steel, alloys, electroplating and rechargeable batteries, all of which are integral to our economic growth and development (Eckelman, 2010).However, nickel production is energy intensive and therefore susceptible to emerging climate change policies, which may lead to production curtailment and/or increased unit costs of production unless changes in efficiency or energy sources are made (Mudd, 2010). The industry is faced with multi-faceted constraints: future technology must not only deal with metallurgical, financial and environmental constraints but also promote low energy and low carbon practices. This presents a challenge for this industry where technology innovation, development and commercialization are often lengthy, risky and costly processes (Imrie, 2006).Climate change is one of the many challenges faced by our society. Others include other pollution to air, water and land, resources shortage and economic development. From a policy perspective, it is important to balance multiple and often competing needs in an integrated manner. It would require some levels of trade-off in order to maximize the overall effectiveness but also to ensure that one policy does not undermine other policy objectives.The aims of this study are to evaluate how developments in climate change policy would affect the nickel industry in the context of existing environmental regulations and how the industry could respond under these constraints."

Jan 1, 2012

By R. A. McGuire

THE recorded production of the Sheep Creek camp from 1900, when the Yellowstone Mining Company first put its mill into operation, to the present day is in excess of $17,500,000. Of this total, $2,500,000 can be attributed to the early period from 1900 to 1916, at which time increased costs of labour and material due to the Great War forced abandonment of any operations on a large scale for a number of years. Since the camp was revived in 1929, at which time the Reno mine started large-scale operations, and the early 'thirties', when the increased price of gold induced the commencement of operations on other properties in the district, total gross production has been in excess of $15,000,000. In addition to the above totals, intermittent shipments were made by lessees and small operators, principally during the period of inactivity from 1916 to 1929, but no records of this production are available. The Sheep Creek camp would rank fifth in the Province-behind Rossland, Portland Canal, Bridge River, and Hedley-in gross gold production, but, because of relatively inexpensive mining and milling costs, would occupy a more prominent position in regard to total dividends paid. Operating mines at the present time include Reno Gold Mines, Gold Belt Mining Company, Kootenay Belle Gold Mines, and Sheep Creek Gold Mines. Each one of these companies, with the exception of Kootenay Belle, represents a consolidation of several smaller properties, all of which were in existence for a number of years prior to 1929. These four companies, at the present time, own, or hold options on, practically all the important claims in the district with the exception of a very few claims and fractions still held by private owners.

Jan 1, 1942

By M. C. Villeneuve

A numerical modelling approach was developed to explicitly simulate geomechanical characteristics of intact rock: mineralogy, grain size and fabric. The approach involved creating a representative constitutive model for each of three common rock-forming minerals: mica, quartz and feldspar. The constitutive models developed are valid within the low confinement realm of excavation boundaries, where tensile fracture processes dominate. The mineral types were assigned to numerical elements, which were associated with each other through an algorithm created in a finite difference model, FLAC 2D (Itasca 2007a), to simulate real crystal geometries and orientations. The numerical models were used in a parametric investigation of the geomechanical characteristics and compared with published observations of the rock yielding process in laboratory testing. This approach has allowed the explicit grain-scale investigation of the impact of geomechanical characteristics on rock yielding at low confinement, leading to an improved mechanistic understanding of excavation-scale rock yielding processes at excavation boundaries.

May 1, 2009

By X. Cao, J. J. Jonas, Wanjara. P., J. Gholipour, E. Dalgaard

The linear friction welding (LFW) behaviour of near-ß titanium alloy Ti-5Al-5V-5Mo-3Cr (Ti- 5553) was investigated. Microhardness measurements were performed in order to evaluate the mechanical properties of the welded material. The linear friction welded (LFWed) Ti-5553 was examined with optical microscopy and scanning electron microscopy (SEM) to evaluate the microstructure’s response to the thermomechanical conditions. Characterization of the welds included analysis of the microstructural features of the weld region and thermomechanically affected zone (TMAZ) in relation to the parent material.

Jan 1, 2010

By Lawrence Devon Smith

"What is Due Diligence?Within the mining industry the term “due diligence” is used to describe a detailed data review, generally in connection with the purchase or sale of a mineral property, the approval of a large capital expenditure, or the borrowing of a large sum of money.The term originates in the requirement of the board of directors of a corporation to “act honestly and in good faith ... and exercise the care, diligence, and skill that a reasonably prudent person would exercise in comparable circumstances” (OBCA, 1994). Furthermore, the law assumes that a corporation (or its board) will have exercised due diligence in the acquisition of an asset and, therefore, knowingly (in the absence of fraud or deceit) will have taken on the liabilities and obligations associated with the asset (Nelson, 1994). This is the familiar “Buyer Beware”.Directors are liable for their decisions except “if the director relies in good faith upon financial statements of the corporation represented … by an officer of the corporation or in a written report of the auditor, or a report of a lawyer, accountant, engineer, appraiser, or other person whose profession lends credibility to a statement made by any such person.” (OBCA, 1994).Hence the importance of reports prepared by professionals. They provide confirmation that the directors have exercised due diligence in the performance of their duties. For this reason these reports are referred to as due diligence studies"

Jan 1, 1997

By Lawrence Devon Smith

"Within the mining industry the term “due diligence” is used to describe a detailed data review, generally in connection with the purchase or sale of a mineral property, the approval of a large capital expenditure, or the borrowing of a large sum of money.The term originates in the requirement of the board of directors of a corporation to “act honestly and in good faith and exercise the care, diligence, and skill that a reasonably prudent person would exercise in comparable circumstances” (OBCA, 1994). Furthermore, the law assumes that a corporation (or its board) will have exercised due diligence in the acquisition of an asset and, therefore, knowingly (in the absence of fraud or deceit) will have taken on the liabilities and obligations associated with the asset (Nelson, 1994). This is the familiar “Buyer Beware”.Directors are liable for their decisions except “if the director relies in good faith up on financial statements of the corporation represented by an officer of the corporation or in a written report of the auditor, or a report of a lawyer, accountant, engineer, appraiser, or other person whose profession lends credibility to a statement made by any such person.”(OBCA, 1994).Hence the importance of reports prepared by professionals. They provide confirmation that the directors have exercised due diligence in the performance of their duties. For this reason these reports are referred to as due diligence studies."

Jan 1, 1996

By George M. Douglas

The southeastern shores of Great Slave lake present a curious anomaly in geographical and geological exploration, in that an area so large and important, and withal so comparatively accessible, should nevertheless have remained unexplored, unmapped, and indeed almost unknown, until quite recent" times On their return from the famous journey to the mouth of the Coppermine, the band of Indians with whom he travelled led Samuel Hearne across Slave lake. He was the first white man to see that great body of water and it is rather curious that it should have been seen first from the north rather than from the south. Hearne's account of the lake is vague, and he made no attempt ?to map the part through which he travelled. About 30 years later John Franklin, on his first journey to the Arctic, crossed the lake from the mouth of the Slave river to the Yellow Knife river. Franklin's maps show all of his route in accurate detail, except that part of it which lay through Slave lake. In 1833-34, Captain, afterwards Sir George, Back made the first exploration of the eastern end of the lake. Captain Back was then on his way to the Arctic coast by way of the Great Fish river, and his Indian guides led him through Great Slave lake by the route they had followed from time immemorial. This route, partly because of its directness, and partly because of its sheltered character, lay through the great mass of islands in the middle of the lake to the Talthei narrows, and thence along the sheltered north shore with its many coves and harbours. Pere Petitot made extensive journeys in Slave lake as well as other parts of the far north.

Jan 1, 1929

By A. H. Lang

"The name Barkc:rville district is applied loosely to the gold-bearing area around the historic town of Barkerville; the first mining camp in western Canada. The region is partly in the Cariboo mining division and partly in the Quesnel mining division. It contains two producing lode gold mines; the Cariboo Gold Quartz and the Island Mountain; and numerous other deposits. The regional structural pattern is outlined in this paper; the structural details of the producing mines are described in the papers that follow.The discovery of rich placer deposits in this district in 1860 was followed by the Cariboo gold rush. Placer mining in the area flourished until 1875 and then declined as the shallow diggings were exhausted, but important operations are still active. The total placer production amounts to about $50,000,000. An extraordinary number of quartz veins outcrop in the district, but many have only a small gold content. The miners soon recognized that the placer gold must have been derived from the erosion of these veins, and some directed their attention to the possibility of quartz mining. The erection of a 4stamp mill in 1876 was the first attempt at ore reduction in British Columbia, exclusive of arrastras. Efforts to mine the Cariboo lodes on a large scale were not successful, however, until 1933, when, due to the pertinacity of F. M. Wells and to the increased price of gold, the Cariboo Gold Quartz mine commenced production, followed by the Island Mountain mine in 1934. This success led to development work at many properties in the district, but the only ones that have reached production to date are the Columbia Tungstens, where scheelite has been mined intermittently since 1937, and the Cariboo Hudson, from which gold was produced in 1938 and 1939."

Jan 1, 1954

By S. Tuttle, R. Sisson

"Suncor Energy Inc. has proposed a 2.2 billion dollar expansion to the current oil sands operation, which will more than double the productive capability of the facility. As part of the application for this expansion, a comprehensive closure plan had to be developed and filed.Closure planning includes a systematic evaluation of the area to be developed, the development activities planned, the goals and objectives of the corporation in re-establishing landforms and ecosystems at the same time as running an effective operation. As early as is practical during the mine development, surface contouring is completed, soil is reconstructed, and vegetation, surface drainage and wetlands are re-established. Once active reclamation is complete and vegetation has been re-established, Suncor monitors maturation of landscapes and ecosystems to provide the submission basis for reclamation certification"

Jan 1, 1999

By Wei Sun, Jaewon Choung, Zhenghe Xu, Zhangming Cui

"High intensity conditioning has been demonstrated in a number of cases to enhance fine particle flotation. The improvement could be attributed to the enhanced formation of particle aggregates. However, the understanding of aggregation mechanisms remains rather limited. Recently, an enhanced particle aggregation was observed by the formation of small air bubbles resulting from high intensity agitations (HIA). In this study, a novel visualization system is designed and constructed for characterizing the fine bubbles formed in an HIA cell. The new design allows determination of gas evolution and bubble size distribution. With this system, the effect of dissolved air on fine bubble generation by HIA is investigated. The results show that HIA creates a favorable environment for the formation of gas nuclei and small size bubbles due to hydrodynamic cavitation.INTRODUCTIONFlotation is a dominant separation technique employed by mineral industry to recover the valuable mineral particles. However, in general, particles finer than approximately 10 µm are not effectively recovered by conventional froth flotation technique due to their low inertia and high specific surface area (Fuerstenau, 1988). Therefore, the fine particle flotation has been considered as the central challenge of flotation research. Substantial advances have been made for fine particle flotation from both a theoretical and technological point of view (Fuerstenau et al., 1979; Song and Lu, 1990; Subrahmanyam and Forssberg, 1990; Sivamohan, 1990; Sedat and Barry, 1991; Matis, 1995). High intensity agitation (HIA), for example, has found some success to improve fine particle flotation kinetics in laboratory tests (Chen et al., 1999a and 1999b; Valderrama and Rubio, 1998; Rubio and De Brum, 1994).The effect of mechanical agitation on flotation kinetics has been recognized for many years. In mid-1970s, Warren (1975) reported that increasing the shear rate of the pulp could improve the efficiency of ultra fine particle flotation. He attributed this improvement in flotation to the formation of aggregates. This concept of aggregation has been extended by Rubio (1978), and Bulatovic and Salter (1989), who employed high intensity agitation (HIA) method to promote aggregation. They found that HIA with the addition of collectors, frothers and suitable modifiers significantly improved both the flotation recovery and selectivity of ultra fine sulphide minerals. The improvement was explained by warren’s shear flocculation theory. Till now, many studies (Chen et al., 1999a and 1999b; Valderrama and Rubio, 1998) have been undertaken to improve fine particle flotation by HIA. However, most of these studies were focused on the relation between energy input and flotation efficiency. Less information was available for describing how the aggregate formed during HIA process."

Jan 1, 2006

By Adil Aledresse, Louis Mercier, Laxman Amaratunga

"The development of high capacity adsorbents with uniform porosity denoted, MP-HMS (Mercaptopropyl – Hexagonal Mesoporous Structure) using nanotechnology, and their ability to extract gold from solution, is presented. The preparation of highly effective heavy metal ion adsorbents by the incorporation of thiol moieties into the pore channels of mesoporous silica molecular sieves has been the subject of many nanotechnology research investigations. The unique feature of these nanoporous adsorbents is their ability to adsorb gold ions from ultra-low concentration solutions like mine effluent as well as from leached solutions in gold mills. The preliminary studies from laboratory simulated gold solutions show that the adsorption capacities of these materials are also among the highest reported. MP-HMS has shown the capability to adsorb 370 mg gold per one gram of the nanomaterials from Tetrachloroaurate solution (up to 37% of their weight). Experimental studies indicated that the maximum adsorption of gold (as high as 99.9% recovery). The current studies will be extended to investigate the interaction of ionic gold complexes with nanomaterials. Future development of this work may lead to either to replace the conventional CIP/CIL processes or use nanomaterials in tandem with the former, suggesting plausible use of mesoporous material in pulp, MIP or in leach, MIL, as a novel gold extraction process.INTRODUCTIONGold typically occurs at very low concentrations in ores less than 10 g/t or 0.001% (mass basis). At these concentrations the use of aqueous chemical (hydrometallurgical) extraction processes is the only economically viable method of extracting the gold from the ore. Typical hydrometallurgical gold recovery involves a leaching step followed by the separation of the gold bearing solution from the residues, or adsorption of the gold onto activated carbon adsorbent. After elution from the activated carbon the gold is further concentrated by precipitation or electrodeposition."

Jan 1, 2008

By C. O. Stee

Introduction The property of Siscoe Gold Mines, Limited, is located on an island of three hundred and forty acres in lake Kienawisik, about fifty-two miles east of Noranda and forty-three miles south of Amos, Quebec. Lake Kienawisik is a part of the Harricanaw drainage system and is crossed by the main line of the Canadian National railway at Amos. This waterway is navigable for boats with a draught of six to eight feet. Diesel engines have been the source of power at the property since milling operations were commenced in January, 1929. The power plant as first designed and built was for a milling capacity of 100 tons. Two Polar-Atlas units, each of 200 h. p., comprised the original installation. With the growth of the 'mine, more engines were added until, at the present time, there is installed at the Siscoe what is rated the largest Diesel plant at any mining property in Canada. Definition of a Diesel 'The Diesel engine is an internal combustion engine which works with liquid fuel introduced after, and independently of, the air charge at a time when communication between the cylinder and the outside atmosphere is cut off, and which ignites the fuel by compression-beat and stored combustion-heat unassisted by heat sources outside the cylinder itself while the engine is in stable operating condition"(1).

Jan 1, 1934

By D. E. Calisaya, É. Poulin, A. Desbiens, R. del Villar, A. Riquelme

"A 15 cm diameter by 732 cm height, fully automated pilot column was installed in the Agnico-Eagle’s Laronde concentrator (Québec), for evaluating the performance of newly developed sensors and advanced process control algorithms. For eventual comparison purposes, the pilot column is continuously fed with the same slurry feeding the copper-circuit third cleaner column. It is equipped with electrical conductivity-based sensors for estimating the three variables used in the multi-variable control algorithm under evaluation: froth depth, fraction of wash water underneath the interface and gas hold-up. Froth depth is regulated using a PI controller while a predictive controller is formulated as the minimization of the tracking errors of gas hold-up and bias rate, keeping several operating constraints between their practical upper and lower limits. In particular, an unreachable high set point of gas hold-up can be selected in order to maximize the bubble surface area available for particle collection, while maintaining bias rate above a minimum value required for froth cleaning. The proposed strategy may indirectly help optimizing flotation column operation by using these secondary variables, without the implementation of a real-time optimization layer.INTRODUCTION Flotation columns have already been used for more than 30 years, mainly in cleaning stages, as a result of their froth washing capabilities. Despite their widespread usage, the measurement of some pertaining variables and their use for automatic control is rather scarce. Among the most important variables directly related to the process metallurgy (concentrate grade and recovery), froth depth (hf) is the only one normally monitored and controlled. Even though commercial sensors are available, gas hold-up (eg), a variable directly related to concentrate recovery, is seldom measured and never controlled. Another important variable, bias rate (Jb) responsible for concentrate cleaning, is simply not measured at all, as there is no commercial sensor available. Therefore, besides froth depth, continuous monitoring of process variables is limited to flow rates (gas, feed, tailings, wash water), i.e. to manipulated variables. Some new available sensors have been industrially tested, e.g. the Sonar-TracTM for eg (O'Keefe, Viega & Fernald, 2007) and the McGill hold-up sensor (Tavera & Escudero, 2002). Others, for bias rate and frother concentration, have been successfully validated at laboratory scale by Laval’s LOOP researchers (Maldonado, Desbiens, del Villar & Chirinos, 2008b; Maldonado, Desbiens, del Villar & Aguilera, 2010a). Some devices have been extensively used for monitoring bubble size and space distri-bution, e.g. McGill bubble viewer (Gomez & Finch, 2007) and others."

Jan 1, 2012

By R. Wang

"Under high stress conditions, rock bursts, borehole breakouts, and spalling events are common phenomena that occur around underground openings. In general, together these three phenomena represent brittle failures of an intact rock mass; however, individually they reflect different failure modes under high stresses. After analyzing and comparing the stress-to-strength criteria for rock bursts, borehole breakouts, and spalling events, proposed by previous researchers, it is found that these brittle failure phenomena share common stress-to-strength prerequisite. The stress-to-strength preconditions for brittle failures can be defined by the ratio of the maximum tangential stress around an underground opening to the uniaxial compressive strength (UCS) (s?max/sci) or by the ratio of the maximum far-field principal stress to the UCS (s1/sci). Both these indicators can be used to reflect the same stress preconditions. For s?max/sci, a ratio of 0.4±0.1 represents the critical stress requirement for brittle fracture. However, for s1/sci, a ratio of 0.15±0.05 should be considered as the critical stress requirement. Numerous engineering case studies and analysis of rock mechanics based on the Hoek-Brown criterion also verify these two stress-to-strength preconditions. Here, these two indicators are presented with an error range because complex rock mass quality ratings, lithology, and geotechnical conditions have profound impacts on the stress-to-strength preconditions for brittle failures. INTRODUCTIONHigh stresses are one of the most important factors that must be considered when undertaking underground rock mass projects (Kaiser et al., 1998). Wang et al. (2009) reviewed current progress in the evaluation of high stresses and their corresponding criteria. However, after clarifying the definition of high stress, civil engineers need to understand the deformation and failure behaviors of rock mass around an opening under high stresses. Under high stress conditions, the deformation of rock masses around an opening can be categorized into two groups, i.e., severe brittle failures (or rock bursts) and compressional plastic deformation of the surrounding rock mass, as indicated in Figure 1."

Jan 1, 2015

By David Whittle

When does a project with questionable viability, warrant further investment? There are cases in which projects, which evaluate to a negative mean probable value, are worth investing in. There are also cases in which projects that evaluate to a positive mean probable value, should not be invested in. The author will present a model for ?project-control?which includes an adaptation of a well know grade-control concept. Comments on Resources and Reserves ?Resource and Reserve estimates are based on positive information (43-101). ?Reserve and Resource confidence qualitatively assessed. ?U.S. Geological Survey (USGS) recognizes Undiscovered Resources (U.S. Geological Survey 2003).

May 1, 2006

By S. Klingmann

ABSTRACT In this paper, we used data collected from the Gibraltar mine to analyze the effect of the TyreSense tire monitoring system on tire performance by reducing tire wear and preventing premature tire failure or damage. We analyzed the relationship between tire temperature, tire pressure, and tire failure or damage to help better understand the importance of controlling high tire temperature and pressure. The results enhance and expand the knowledge of the management of tire operational pressure and temperature.

Jan 1, 2014

By C. A. Sutherland

"Smelting of copper-gold ore from nearby Rossland mines started at Trail in the 1890s. As ore from the Rossland mines became exhausted, lead smelting of hand-sorted galena ore from other British Columbia mines was initiated. With the development of flotation technology for the separation of lead, zinc, and iron sulphides in the first two decades of this century, the large Sullivan orebody at Kimberley, British Columbia, became the f oundation for the growth of a major zinc and lead smelter at Trail. Lead smelting began in 1901, electrolytic zinc in 1916, and by 1984, the Trail metallurgical complex had produced 10 million tons of each metal. Its present capacity is 270000 tonnes per year of zinc and 110 000 tonnes/year of lead.This paper reviews the history of technological changes in the Trail production plants, emphasizing the zinc plant modernization program started in the 1970s, and also the planned introduction of the QSL oxygen lead smelting process in the late 1980s. Lead modernization will increase production capacity to a maximum of 160000 tonnes per year.IntroductionCopper-gold ore was discovered at Rossland, British Columbia, in the year 1890, starting a mining industry that was to last over three decade s. Selected ore was at first transported at high cost to distant U.S. smelters, so there naturally followed a decision to construct a small copper smelter to process the local ore to matte. It was built in 1896 at the mouth of Trail Creek on the Columbia River, about 10 km from Rossland. This little smelter was to develop and diversify in the next 90 years into the world 's largest lead-zinc producer).The mining boom that occurred in the northwestern United States and southeastern British Columbia in the period of 1890 to 1910 saw the brief operation of many small local smelters. The only one to survive was the smelter at Trail. The circumstances that permitted its continued life and subsequent growth, form a fascinating history of business deals, litigation, andsteady technical progress.Early investment in local railway transportation and options by F.A. Heinze, the smelter' s founder, attracted the attention of the Canadian Pacific Railway Company, which purchased Heinze' s assets in 1898. This provided the capital base for survival and growth of the smelter, which remained and prospered under the Canadian Pacific umbrella for almost ninety years. It was registered as the Consolidated Mining and Smelting Company of Canada Limited in 1906; in 1966, this name wasshortened to Cominco Ltd.The Rossland mines continued to supply copper ore for the smelter until the late 1920s, but lead-silver ore also became available from the contemporary mining boom in the Slocan area, about 80 km away. In 1901, the Trail smelter diversified into lead; and when the CM&S Co. acquired the St. Eugene Mine at Moyie and the Sullivan Mine at Kimberley, the smelter was guaranteed a firm supply of lead ore. The company also purchased the West Kootenay Power and Light Company, which even before the turn of the century had constructed the first of four hydroelectric generating plants on the Kootenay River near Trail. This acquisition assured the CM&S smelter and its local mines of a stable power supply and the opportunity to diversify into power intensive technology."

Jan 1, 1988