Search Documents

By Helge B. Wurst, Michael P. Cipold, Jan F. Bachmann, Claus C. Bachmann

"In washability, the objective is to establish the set of maximum possible separation performance criteria for a given mineral feed. The method of choice for this has been the conventional sink-float analysis. Time, cost and safety aspects of the sink-float method have prompted the search for a new approach for establishing separation performance criteria, especially as performance levels of separator plants can be maximized if reliable information based on an analysis of washability in conjunction with particle size distribution, elemental constituency becomes readily available. The new method to establish washability and associated performance information utilizes at least two measurement technologies concurrently: single energy x-ray transmission and image processing. For porous or very inhomogeneous materials the results can be refined further by using dual energy x-ray transmission and image processing. The value of the collected data increases considerably if the washability data were additionally available in time to be considered in the control of the process plant. The incorporation of an automated washability monitor gives near real-time data that would impinge positively on the profitability of the plant operation. The method was extensively tested with a range of sample with different densities, varying from 1 g/cm³ (coal) to 5 g/cm³ (iron ore).INTRODUCTIONWashability of minerals like coal and iron ore is expressed by a curve or graph showing the results of a series of float-and-sink tests. Several of these curves are drawn to illustrate different conditions or variables, usually on the same axes, thus presenting the information on one sheet of paper. Washability curves are essential not only for the design but also for the operation of preparation plants.In determining the washability analysis, particle density is the underlying feature of all washability curves. Conventionally, the particles are separated into density fractions by immersing them in fluids of a predetermined density followed by skimming of those particles that stay afloat. The particles remaining afloat thus have a density lower than that of the fluid they were subjected to. The particles that remained at the bottom of the fluid container thus had a higher density higher than that of the fluid. By progressively increasing, for example, the density of the fluid and immersing the remaining particles so as to be able to skim the next density fraction, the particles would be fractionated into density groups. The liquids used range from aqueous solutions to organic liquids to suspensions. Unfortunately the liquids used for this separation process are often toxic and expensive. It stands to reason that a new method of determining washability is sought."

Jan 1, 2016

"In an environment of rising energy prices and mining at greater depths, cost-efficient loading and hauling equipment is essential. Conducted at an underground mining operation, this study analyzes the energy consumption and gas emissions of diesel and electric load-haul-dump machines (LHDs) with similar bucket capacities. Based on energy prices from the first quarter of 2014, results of discrete event simulation show that energy costs for diesel and electric LHDs are US$0.24/t and US$0.07/t, respectively. Also, diesel LHDs emit 2.68 kg CO2 per litre of diesel fuel, whereas using electric machines reduces the need for ventilation to mitigate engine heat and emissions and reduces energy costs.RÉSUMÉ Dans un contexte de croissance des prix de l’énergie et d’exploitation minière à des profondeurs de plus en plus grandes, il est essentiel d’avoir des équipements de chargement et de transport les plus rentables possible. La présente étude, effectuée dans une mine souterraine, analyse la consommation énergétique et les émissions de gaz de chargeuses-navettes (LHD) au diésel et à l’électricité ayant des capacités de godet similaires. En se basant sur les prix courants de l’énergie, les résultats d’une simulation d’événements discrets montrent que les coûts énergétiques pour les LHD au diésel et à l’électricité sont respectivement de 0,24 $US/t et de 0,07 $US/t. De plus, les LHD au diésel émettent 2,68 kg CO2 par litre de combustible diésel alors que les machines utilisant l’électricité réduisent le besoin de ventilation pour atténuer la chaleur des moteurs et les émissions en plus de réduire les coûts énergétiques."

Jan 1, 2015

By R. W. Davis

INTRODUCTION CHURCHILL river was named for John Churchill, first Duke of Marl-borough and third Governor of the Hudson's Bay Company, in the latter part of the 17th century, some fifty years after the ill-fated Danish expedition, led by Munck, had abandoned the site of the now famous seaport of Churchill, as a worthless, cold, disease-ridden country. No other attempts were made to explore the interior until the river basin became a part of the grant to the Hudson's Bay Company and began to play its part in furnishing the luxury of fine furs to civilized people as it had furnished the necessities of food and dress for untold centuries to uncivilized natives. This was the sole contribution of the region to the economic life of the country for some two hundred and fifty years, until 1926, when the power site at Island Falls was discovered by engineers seeking a cheap power source to make possible the development of the great ore-body at Flin Flon. DRAINAGE BASIN OF CHURCHILL RIVER The river is some 1,325 miles long. Rising in the headwaters of the Beaver river, in east-central Alberta, it flows in an easterly direction across Saskatchewan and northeasterly across Manitoba to Hudson bay, through a remarkable basin of some 115,500 square miles, only 6,000 square miles less than the area of the British Isles. A journey down this river leads one through three distinct belts of country, each vastly different from the others geologically and in surface characteristics. For the first five hundred miles the river flows through a basin of 36,000 square miles of the great central-plains country, which is covered with fertile soil and carpeted in its southern part with prairie grass, which gradually gives way to the mixed forests of poplar, spruce, birch, and jackpine in the northern and eastern sections: About midway across Saskatchewan, bald-headed knolls and ridges begin to make their appearance as the river meets the western margin of the Canadian Shield. Then, for some seven hundred miles, it passes through country underlain by the pre-Cambrian rocks of the Shield, which continue to within one hundred miles of Hudson bay. Here the character of the country again changes to a low, clay plain underlain by sandstone, and through this 'clay belt' the river flows between steep clay banks, to empty into Hudson bay.

Jan 1, 1935

By Shigeomi Nishigaki

This paper presents quantitative indexes to evaluate operator?s bearing, difficulty in a task, and machine operability when an operator remotely controls a backhoe, and reports the use cases. The quantitative indexes would give her/him the opportunity to reflect on her/his works, and enable us to gain in-depth insight into the teleoperation, and furthermore give us with promising hints to improve it.

Aug 1, 2013

By C. I. Walker

Field tests at a number of large mineral processing operations have been undertaken to better understand the wear life impact of different aspects of pump design, materials of construction and maintenance procedures. Data are presented for wear rates, and typical result variability is explored. To improve the availability of pumping equipment in a milling circuit it is not only important to improve the wear life, but also reduce the variability in the wear life of components so that the incidence of premature failure is lessened. Localised gouging wear due to flow separation and turbulent eddy formation is often the point at which part-holing occurs. A number of improvements to the design of pump impeller and throatbush (suction side liners) to reduce the localised gouging wear are outlined. Also, results are presented on the use of composite materials (mix of metal, rubber and ceramic) for throatbush materials to protect specific areas against wear.

Jan 1, 2012

By E. L. Bruce

EUROPEAN Russia is mainly a great plain, the average elevation of which is only 600 feet above sea level and the maximum elevation less than 1,200 feet (Figure 1). The main divide between the Arctic ocean and the Black sea and Caspian sea is an indistinguishable topographic feature from which the Dneiper and Don rivers flow southward to the Black sea and the Volga river to the Caspian. The valleys of these rivers are but little below the general level (Figure 2). To the south, this great, rolling plain is broken by a low ridge of Precambrian gneisses and intrusive rocks. The Crimea is an upland from which the descent to the Black Sea coast is precipitous (Figure 3). The Ukrainian Soviet Socialist Republic occupies the southern part of the plain. It is the southwestern unit of the Union, bordered by Rumania and Poland on the west and by the Crimean Soviet Socialist Republic on the south.

Jan 1, 1938

By J. A. Chamberlain

DURING a recent trip across Canada and parts of the northern United States, the. writer examined some forty mine models. Construction -details and the uses to which the models were being put were outlined in a report to Eldorado Mining and Refining, Limited, and a specific model was proposed on the basis of the Company's particular needs at their Beaverlodge operation. It was felt, however, that portions of the report would be of some value to anyone contemplating building a mine model. For this reason, a synopsis of some of the more important aspects of the problem is presented here, together with a suggested model type that appears to have wide application. Thanks are due not only to Eldorado for permission to publish the following material, but also to the many mine personnel across Canada who allowed the writer to examine their models and gave freely of their time in discussion.

Jan 1, 1958

By A. A. Goss

We investigate the relationship between corporate financial performance (CFP) and environmental and social performance (CSP) in a sample (n=165) of large, publicly traded U.S. mining and oil and gas firms. Using optimally scaled principal components analysis to generate aggregate measures of CSP strengths and concerns, we find higher concerns are related to higher volatility of unexpected earnings and discount rates. Furthermore, these earnings shocks are more likely to be negative as concerns increase. Decomposing this relationship shows that negative environmental performance dominates proactive environmental management as a driver of unexpected earnings, but proactive community efforts increase the magnitude of earnings shocks. We document some evidence of the strategic use of CSR, with those firms that have greater risk investing more proactively in CSR.

Aug 1, 2013

By V. Aitken

Line-of-sight radio control has received widespread acceptance for use in many mining methods because today’s technology offers improved economics and personnel safety. Significant advances in higher autonomy for mining machines are not currently seeing widespread use even though they offer great future potential. With autonomous capabilities being a longer-term goal, a logical sequence of advances based on TeleRemote control is proposed. Under Tele - Remote control, the operator is in direct control of the machine at all times. Three levels of Tele - Remote control systems are presented including line-of-sight, extended line-of-sight, and full load-haul-dump applications. Distributed control and sensing subsystems arranged in a vehicle control area network support incremental system expansion through the three levels of TeleRemote control and prepare the machine for integration of higher levels of automation as mature technology becomes available. This approach allows full exploitation of today’s mining automation technology with a flexible future growth path.

Jan 1, 1998

By T. A. Lazier, C. S. Longley

"Paymaster Consolidated Mines, Limited, owns several groups of claims in various parts of the Porcupine district. The area in which mining has been carried on includes parts of lots 5, 6, and 7, con. 1, Tisdale township, and twelve adjoining claims in Deloro township to the south. Highway No. 67A between South Porcupine and Timmins crosses the property.The discovery of the Dome mine in 1909 caused a rush of prospectors to the district and in a few weeks practically all territory adjacent to the Dome was staked. At that time work was started on the West Dome, West Dome Lake, Apex, and Standard properties. These were consolidated in 1930 to form the present Company. Gold was produced from the West Dome Lake from 1915 to 1930, and from the Standard-Paymaster from 1922 to 1928. The total production of the previous and present companies from 1915 to November 30, 1946, has been 487,170 oz. gold and 149,342 oz. silver from 2,337,554 tons of ore."

Jan 1, 1954

By Neil Campbell

"The Pine Point area is on the south shore of Great Slave Lake, 510 air miles north of Edmonton and J JO miles south of Yellowknife, N.W.T. The occurrence there of lead and zinc was reported in J 899 by R. Bell (5) of the Geological Survey of Canada, and in the following years several claims were staked and some prospecting was done. In 1928 Atlas Exploration Co. took over the property containing the discovery occurrences. In 1929 The Consolidated Mining and Smelting Company of Canada Ltd. (""Cominco"") and Ventures Ltd. participated with Atlas in forming the Northern Lead-Zinc Co., which, under the direction of J. M. Bell, carried out 24,499 feet of drilling in the discovery and surrounding areas. Two shafts and many surface pits were also sunk. This work showed that the discovery deposits contain about 500,000 tons of lead-zinc ore, but no new orebody was found.In 1936 D. F. Kidd (11) drew attention to the highly significant space relations between the base-metal discoveries at Pine Point and the projections of certain major Precambrian faults mapped earlier by C. H. Stockwell. Geological work by Cominco in 1940 and subsequent years suggested the presence of mineable deposits within a belt of land including part of the area of earlier field work and extending far beyond it. Between 1946 and 1954 exploration financed by Cominco and Ventures Ltd. included 182,950 feet of diamond drilling, 383 feet of sinking, and 240 feet of drifting, raising, and crosscutting. This work was successful in finding substantial quantities of new ore in places where bedrock is completely concealed.The topography is one of low relief, characterized in many places by swampy muskeg and shallow, marl-bottomed ponds. The area where ore has been found is generally higher ground which, though not well drained, is comparatively dry. It is also marked by raised beaches and a few sand dunes overgrown by small spruce and pine. Bedrock is generally overlain by a variable thickness of hard, glacial boulder clay. This in turn is covered by silt, sand, and gravel, probably deposited from the waters of Great Slave Lake, which formerly extended many miles beyond its present southern shore."

Jan 1, 1949

By H. T. Michels

Recent laboratory studies show that several bacteria, known to be human pathogens, die when they come in contact with copper and copper alloy surfaces. The amount of live bacteria drops by several orders of magnitude, to zero, on copper alloys in a few hours. In contrast, no reduction is seen in the concentration of live organisms on stainless steel during the six-hour test period. Aluminum painted and coated surfaces and plastics would show behavior similar to stainless steel and show no effect. Coatings and other surfaces claiming to be antimicrobial showed little to no effect. These results suggest the selection of copper alloys for surfaces exposed to human touch can materially assist in reducing the transmission of infectious organisms. In order to make antimicrobial claims in the United States, the approval of the US Environmental Protection Agency (EPA) is required. The EPA-required efficacy testing is described and the test results are summarized. It is anticipated, that once regulatory approval is obtained, that this will facilitate the introduction of antimicrobial copper alloys in hospitals, nursing homes and other healthcare facilities, as well as schools, and public buildings. Some of the application and barriers, to entry into the healthcare markets are mentioned.

Jan 1, 2007

By M. E. Grimes

"The future of the uranium industry in Canada during the next twenty years will be very dependent on political and social issues on a world scale. Technology, as such, will tend to be of lesser importance. Nonetheless, some technical changes can be anticipated.This paper deals with milling of uranium ore, leaving further processing and nuclear power production to specialists in these fields. An attempt has been made to look at uranium production technology in Canada in relation to that in other countries, and to draw interference regarding future changes that seem probable in the Canadian context. In particular, recent advances in mill equipment are considered.The chemistry of uranium and its relatively low concentration in most ores has been responsible for a completely hydrometallurgical approach to mill processing, and this should continue. In spite of little commercial success to date, pre-concentration of lower grade ores will be researched further in order that these ores can compete with higher grade deposits in Canada.The discovery of the relatively high-grade ores of the Athabasksa region will undoubtedly influence choice of mill processes and equipment. The potential effect on innovations is discussed"

Jan 1, 1986

By Derek H. C. Wilton

"The Nain Province (NP) of northern Labrador is a >600 km long by =100 km wide Archean craton that has undergone relatively little mineral exploration until economically signifcant concentrations of orthomagmatic nickel sulphide were discovered by Diamond Fields Resources (DFR) at Voisey’s Bay. Due to the great time span between crust formation andfnal intrusive activity (ca. 3.9 Ga to 1.27 Ga),there were, however, numerous metallogenic events within the NP.The NP was intruded by the ca. 1.3 Ga to1.2 Ga Nain Plutonic Suite (NPS) composite anorthosite-granite complex. The NPS dividesthe NP into the southern Hopedale Block (90 km by 150 km) and the northern SaglekBlock (375 km long by =50 km wide). These two blocks appear to represent two distinct Archean cratonic nuclei, each with its own distinct metallogenic history. The NPS is a coalesced assemblage of composite intrusions which include anorthosite, troctolite, norite, gabbro and granite.The Hopedale Block contains the Hunt River and Florence Lake greenstone belts, and the Weekes Amphibolite which represents remnantsf the older Hunt River greenstone belt. Geologically, these belts have some potential to host komatiitic Kambalda-style nickel, volcanogenic massive sulphide (VMS) and meso -thermal lode gold mineralization. The unconformity between Paleoproterozoic cover sequences and the trondhjemite-tonalite-granodiorite (TTG)suite which engulfed the greenstones was the locus for lead-zinc-bearing quartz-carbonate veins. Minor fracture-hosted uraninite showings are also present in the TTG.The Saglek Block is a high-grade gneissterrane with deformed Archean supracrustal sequences but no greenstone belts. Within the gneiss are variably-sized enclaves that range in composition from anorthositic to ultramafic; some of these latter xenoliths contain abun-dant fuchsite. There are also three small anorthositic to ultramafic meta-igneous complexes present in the gneiss near Okak Bay.Some Archean meta sedimentary and maficgneiss supracrustal sequences contain iron-oxide and sulphide members. The sulphide-bearing Tasiuyak parag neiss defines the cra-tonic suture between the NP and Churchill(Rae) Province. Along the cratonic suture between the NP and Churchill Province from Ramah Bay north are remnants of the Archean(or Paleoproterozoic) Hutton Anortho site Suite. Ultramafc layers within the suite contain chromite and elevated Ni values.Three ca. 2.0 Ga supracrustal sequenceswere deposited in small fault-bounded basins within the NP. The Snyder Group contains pyrrhotitiferous massive sulphide horizons. TheMugford Group contains SEDEX-like massive sulphide blocks in a debris fow and ultramafic sills with unusual PGE concentrations; alaskitic granite cutting basement gneiss to the group contains stockwork-like pyritiferous quartz veins. The Ramah Group contains numerous MVT-style zinc-lead sulphide occurrences.The Reid Brook Intrusion of the NPS contains enormous and high-grade nickel-copper-cobalt massive sulphide bodies at the Voisey’s Bay deposit. Exploration in the northern portions of the NPS in 1995 has indicated the presence of other potentially economic nickel sulphide horizons."

Jan 1, 1996

By F. Baerhold

Recycling of hydrochloric acid from the pickling of mild steel using pyrohydrolysis is a state-of-the-art technology. Recent developments have focused on the production of a high value iron oxide by-product, where the chemical purity and physical properties are the main issues. New processing routes, especially for TiO2 and Ni production, use leaching operations with hydrochloric acid. The feasibility of those processes depends on the availability of an economic and reliable process for the recovery of the acid. Depending on the level and type of impurities and the required specification of the by-product, pyrohydrolysis in a fluid bed or in a spray roast reactor can be the ideal solution. In stainless steel annealing and pickling lines, a mixture of nitric and hydrofluoric acids is used to remove the scale from the surface after heat treatment. Nitrate emissions from the pickling and the rinsing processes have to be avoided because of more stringent environmental regulations. An annealing and pickling line that is totally wastewater-free was developed, where not only the nitric/hydrofluoric acid but also the rinse water, is completely recycled. New developments to increase the HNO3-recovery rate and to obtain a metal oxide by-product that is easier to recycle are presented.

Jan 1, 2006

By D. Purdie

"This paper aims to remind researchers, designers, operators, and managers about the benefits of seeding in the design of precipitation stages in their flowsheet. Including a high density solids (HDS™) process encourages the precipitating solids to form on the surface of existing precipitated particles. This paper discusses the application of the HDS technology at Kennecott Smelter, where the authors have witnessed significant improvements in settling and filtration rates. The authors have also applied this technology at various smelter bleed treatment plants worldwide with similar improvements in precipitation and filtration rates. HDS is a registered trademark of De Nora Water Technologies. RÉSUMÉ Cet article a pour objectif de rappeler aux chercheurs, aux concepteurs, aux exploitants et aux administrateurs les avantages de l’ensemencement dans la conception des étapes de précipitation de leur schéma de traitement. L’introduction d’un procédé des boues haute densité (procédé HDS™, de l’anglais high density sludge) encourage la formation de substances solides précipitantes à la surface des particules précipitées existantes. Cet article porte sur l’application de la technologie HDS à la fonderie Kennecott, où les auteurs ont observé des améliorations importantes au niveau de la vitesse de sédimentation et de filtration. Ils ont également appliqué cette technologie à diverses usines de traitement des rejets liquides des fonderies dans le monde entier, et ont constaté des améliorations similaires en termes de vitesse de précipitation et de filtration. Le procédé HDS est une marque de commerce déposée du fabricant De Nora Water Technologies.INTRODUCTION In 1966, the lead author worked as an assistant smelting metallurgist for the Tsumeb Corporation Limited copper and lead smelter in Tsumeb, Namibia. The smelter produced copper and lead, as well as cadmium and arsenic trioxide as byproducts. The cadmium was concentrated in the lead blast furnace off gas dust, and was collected by a baghouse. The baghouse dust was leached with dilute sulfuric acid (H2SO4) in a batch process. The iron and arsenic in the solution were oxidized with potassium permanganate (KMnO4) and basic ferric arsenate (BFAS; Fe(AsO4)x(SO4)y(OH)z·wH2O) was precipitated using milk of lime. The cadmium was cemented from the purified solution using zinc dust."

Jan 1, 2018

By A. Dreimans

Tracing of 'float' against the latest ice-flow directions ha!' led to or assisted in discoveries of several mineral deposits in Canada at lP.ast since 1891, e.g., fluorite and corundum in eastern ?Ontario, Steeprock and Josephine iron ore in western Ontario, Malartic, Fisher-Quebec, and Lamaque gold ore, and Vendome zinc ore, in western Quebec, Sullivan zinc and lead sulphides in British Columbia, Orvan Brook or New Calumet sulphide deposit in New Brunswick, Lynn Lake nickel sulphide de-posit in Manitoba, etc. Pebbles or ore boulders whose source has not yet been found include diamonds in the Great Lakes region and ?sulphides in several localities in Ontario and Quebec. Complexity of transport of ore boulders, including non-glacial transport, may be the explanation. Tracing of ore boulders requires knowledge of the Pleistocene history of each particular area (ice flow directions, their ?changes during glacial oscillations, existence of pre-glacial lakes with ice-rafted boulders, later interference by streams, lakes, mass movements). Important also is distinction of till from similar non-glacial deposits and knowledge of the bed-rock geology. Quantitative methods, e.g., pebble counts, maybe applied while tracing magnetite, hematite, or goethite. Fragments of sulphide ores are less abundant in indicator trains, and quantitative methods are less suit-able for tracing them. Heavy-miner-al investigations may give good results for minerals resistant to weathering. Geochemical methods are of value only in the vicinity of ore deposits.

Jan 1, 1958

By H. S. Price, F. N. Kissell, R. C. McCulloch, J. C. Edwards

"The methane em1ss10n from deep coalbeds which are actively mined is a serious problem facing the mining industry today. Pinpointing the source of methane and predicting the emission of this gas from these coalbeds is necessary if preventive techniques are to be effectively used to control methane emission. In general, because most coalbeds have water associated with them, the system to be studied may be either single-phase (methane gas) or two-phase (methane and water). Because coal mine geometry is complex and the fluids have variable properties as functions of pressure and methane concentration, the differential equations describing the flow of methane and water are not amenable to analytic solution, but must be solved numerically using high-speed computers. This paper presents the development of such a complex mathematical model along with some preliminary applications of the model to methane emission from one- and two-dimensional coalbeds with and without water present."

Jan 1, 1973

By Q. Liu, P. Katsabanis, J. A. Meech

A thermohydrodynamic computer code has been used to simulate dust explosions. For sulphide dusts, the thermodynamic predictions are used to investigate the effect of dust concentration, mineral content and inert materials as well as the quantity of sulphur dioxide produced. It was found that the amount of oxygen available for the explosion is very important and that the dust concentration which gives maximum explosion pressures is obtained at zero or slightly negative oxygen balance values. The sulphide minerals were found to have the following explosibility sequence: pyrrhotite, pyrite, chalcopyrite, sphalerite, covellite, chalcocite and galena, which is in agreement with mine experience. The results show that theoretical calculations can be used to predict explosion pressures and toxic gases produced by a dust explosion and therefore they can assist in the design of protective measures .

May 11, 1988

By G. S. Dobby, J. A. Finch

"I. INTRODUCTIONA significant development in flotation over the past few years has been the increasing industrial use of flotation columns, primarily in Canada. The column differs dramatically from conventional mechanical flotation machines, both in design end operating philosophy, which has been a principal reason for its slow acceptance by the mineral industry. Boutin, Tremblay and Wheeler (1. 2) developed the concept in the early 1960's and since then plant and laboratory columns have been marketed commercially by Column Flotation Company of Canada Ltd. In 1980-81 at Mines Gaspe, Quebec, three columns replaced 13 conventional cleaners in a molybdenum upgrading circuit, with superior results (3). Since then many of the copper producers in British Columbia have installed columns for copper and molybdenum cleaning, including Gibraltar, Lornex, Highmont and Island Copper. There now appears to be widespread interest in flotation columns.The column is particularly attractive for applications involving multiple cleaning stages and can upgrade In a single stage compared with several stages of mechanical cells. This results in simpler, more controllable circuits. Importantly, the column itself is well suited to computer control. A significant problem, however, has been that of translating laboratory data to plant performance. The purposes of this communication are to address the problem of column scale-up and to describe some of the transport mechanisms of a flotation column, leading to a kinetics based model.A schematic of a flotation column is shown in Figure]. Industrial columns are up to 13 m high and 0.3 to 1.8 m in cross section (either square or circular). Three zones can be identified:a collection zone, with feed entering 2 to 3 m below the top of the column and descending against rising bubbles generated at a gas sparger; a washing zone, where a packed bubble bed is generated by a downward flow of wash water; and a conventional froth (2 - 5 cm thick), the sole purpose of which is particle transport to the launder. The tailings withdrawal at the bottom of the column is controlled at a rate slightly greater than the feed flowrate (called a positive bias).An important element is the washwater, added just below the froth zone. The component of the washwater that flows downward (to make up the bias) is sufficient to prevent coalescence of rising gas bubbles. The packed bubble beg so generated is very efficient at suppressing gangue entrainment to the concentrate."

Jan 1, 1985