Search Documents

By Y. Sasseville

"Niobec has been using vibrating screens and screw classifiers as a double stage classification in its grinding circuit since the very beginning of its operation in St-Honoré. Most of the other mineral processing plants around the world uses cyclones as the classification device in their grinding circuit. The difference between these two methods are well known in terms of capital cost and grinding efficiency but the differences in terms of the impact on the downstream processing stages are a lot harder to predict and are case specific. In the interest of lowering the capital cost of a future expansion project, Niobec decided to test the cyclones in its actual grinding circuit and evaluate their impact on the recovery of the downstream processing stages as well as the operating cost of the mill. We switched between cyclones and screens for 8 month in 2013 and early 2014 and we are now operating only with cyclones since march 2014.INTRODUCTIONThe Niobec mine and concentrator were built in the mid 70’s and at that time, the mill was processing 1 500 tons per day. Over the years, many expansion projects have brought the plant to 7 000 tons per day. Throughout the initial concentrator design and commissioning, screens have been chosen over cyclones because of their higher classification efficiency which is known to reduce variability and limit the fine generation especially due to a high undersize classification efficiency. Just like many other plants, fine particle generation is a major problem at Niobec because of its negative effect on downstream processing stages. In the interest of lowering the capital cost of a future expansion project, Niobec’s engineering team decided, 35 years later, to test the cyclones in its actual grinding circuit and evaluate their actual impact on the final recovery and the operating cost of the mill.The grinding circuit is separated in two lines which will be called Circuit #1 and Circuit #2 along this paper. Circuit #1 is, as you can see in Figure 1, composed of a rod mill and two parallel ball mills in closed circuit with screens and screw classifiers. The screens oversize are sent to the screw classifiers while the undersize are sent to the next processing stage. The screw classifiers overflow are both sent back to the pump box while their oversize streams return in their corresponding ball mills for further grinding. Circuit #2 is, as you can see in Figure 1, quite the same as Circuit #1 except it has only one set of screw classifier and ball mill. Figure 1 also shows the modification in arrangement each circuits went through to integrate the new cyclones. One of the ball mills in Circuit #1 now appears dotted because it can still be used but is not now"

Jan 1, 2015

"Gravity concentration remains the main separation method for fine iron ore and is used extensively for treating various minerals. Gravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid, such as water or air (Wills, 2006).Spirals concentrators are one of the gravity concentration equipment used for beneficiation of minerals. Spirals are typically used for processing of fine minerals (-1mm) size fraction. The main operating variables for a spiral concentrator are the feed rate, the solids concentration, the wash water addition and the position of the cutters or splitters used to separate the tailings, middling and concentrate streams (Sadeghi, Bazin & Renaud, 2014).The aim of this study is to investigate the effect of feed rate, solids concentration and wash water on grade and recovery on iron ore material. The Multotec SC20HC/7 WW spiral was used for the experimental test work. The spiral was tested at varying solids concentration and feed rate. The wash water rate was also varied to establish the best washing rate. The splitter positions were kept constant. Optimization of these variables is expected to provide optimum conditions for a good compromise between grade and recovery.INTRODUCTIONSpiral concentrators are simple low energy consuming devices that separate minerals mainly on the basis of density. Spirals are widely used in mineral processing as a method for preconcentration and have proven to be metallurgically efficient and cost effective.Spirals have a wide application, they are used in iron ore processing, coal, gold, chromites, mineral sands, glass sands, and in soil cleaning.Separation on a spiral is achieved through a combination of forces that act on particles as they move down the trough of the spiral. The main forces known to act on the particle on a spiral are the gravitational forces, centrifugal force, hydrodynamic drag, and lift and friction forces (Kapur & Meloy, 1998). Apart from the forces acting on a spiral, the properties of the slurry flowing on a spiral including, solids concentration, feed rate and wash water also plays an important role in the separation on the spiral.The relationship between separation efficiency and feed rate was shown to be linear, with a decrease in efficiency at higher flow rates. Previous work on flow profile by Holland - Batt (1990) indicated that any increase in the feed rate to a spiral results in a greater part of the additional flow volume reporting to the outside of the trough. The flow on the outside of the trough becomes energized and consequence to that the heavy particles find it hard to settle and escape this region to the inner region. This effect has a high impact on recovery of heavy minerals, since any increase in volumetric flow on the spiral is not made available for recovery in the inner region of the spiral."

Jan 1, 2015

By Arun Verma

Thermal energy storage offers a means of effecting significant costs savings and conservation of premium fuels. Na2SO4 has been found to be a good material for storing thermal energy in the medium-temperature range, mainly because of its dimorphic nature and high heat of transition. Basic data and development of the salt to a practically usable block are discussed.

Jan 1, 1978

By D. Bouchard, M. Forté, A. Charette

A transparent replica of a casting die was built to achieve a better understanding of the filling mechanisms of aluminum in high pressure die casting. Water and tomato paste were respectively used as analogues for the Newtonian liquid aluminum and the non-Newtonian semi-solid aluminum. The transparent die was installed on an industrial casting press and filling was filmed with a high-speed camera. Differences between the Newtonian and non-Newtonian fluids are presented and discussed.

Jan 1, 2006

By Marco A. Vera

"This paper investigates the froth function in flotation and the associated upgrading process. Flotation literature has revealed that one of the main functions of the froth phase is the cleaning of bubble-particle aggregates by rejection of entrained material. The cleaning and transport processes across the froth phase exert straining forces on these aggregates on their way up to the froth surface. These forces will impact on the recovery of bubble-particle aggregates.The grade at the top of the froth (TOF) is a parameter related to the quality of particles collected by bubbles in the pulp zone (true flotation). It has recently been demonstrated that TOF corresponds to the maximum practically attainable grade described by the recovery-grade (or enrichment ratio) curve. TOF lumps all the processes experienced by the bubble-particle aggregates before reaching the launder concentrate. This paper describes a methodology for quantifying flotation performance by means of the top of the froth sample - a touch of froth.INTRODUCTIONFroth flotation may be the most important mineral processing technique, but its theory is complex and is not completely understood even though many aspects have been studied and reviewed (Teague, 1998; Wills, 1992).Two distinct particulate systems prevail in the flotation process: a pulp phase and a froth phase (Figure 1). The pulp zone had been studied extensively; however, it is only recently that techniques to measure the froth zone performance have been developed (Contini et al., 1988; Falutsu and Dobby, 1992; Feteris et al., 1987; Seaman, 2002; Vera et al., 1999b).Flotation involves a number of mass transfer processes, occurring in the pulp phase and the froth phase. The formation of the froth and its subsequent removal are considered to be two important steps of the process. Phenomena that occur in the froth phase are known to affect flotation performance significantly (Cutting et al., 1981).Because the froth has a high free surface energy (as a result of the extensive interfacial surface between liquid and air), it appears thermodynamically unstable. The foaming is a dynamic balance, as new bubbles are added continuously from the pulp, while others disappear from the top. Under steady-state conditions, the volumes of added and subtracted air are equal (Booth, 1953)."

Jan 1, 2003

By Jerry Ran

Stope back caving in a mine using open stope mining interrupts the planned mining sequence and causes oversize muck and dilution with adverse economic implications. As many underground mines are mining or have plans to mine at depth, stope back caving could have significant impact on the mine sustainability. Therefore understanding the caving mechanism is important in preventing future occurrence and improving the mine economic performance. Falconbridge Ltd Kidd Mine is an underground mine using open stope method producing more than 2 million tonnes per year. Its current lowest mining level is approximately 2070m below surface and the lower portion of the orebody is being developed. In years of 2002 and 2003 the back of three stopes of approximately 1900m and 2040m below surface caved and caused substantial mining difficulties at the mine. As these caved stopes are subject to stress concentration, seismic activities and near major geological structures, the caving mechanism is much more complex than that of stopes near surface. In addition to the recorded caving history by site observations, the mine carried out cavity surveys and test drilling to define the caved profiles. The mine seismic monitoring database provided information at these stopes. Stress modeling work conducted by an external consultant provided the stress patterns at the caved stopes. Based on the field collected data and stress and seismic information, this paper presents details of the stope caving process and cavity surveyed profiles, reviews the predictability of the stability graph approach for these cases, discusses the caving mechanism and proposes preventive measures to stabilize the stope back.

May 1, 2004

By Lawrence Winter

why are these deposits significant? (i) economically and (ii) in a VMS/geological context. ?Significance of the tectonic setting. ?New understanding of the regional geology: volcanic stratigraphy, first geochronologic data. ?Deposit geology: paleomorphologyof the seafloor setting. ?Lessons and conclusions ?Regional Potential

May 1, 2006

By Charles Knilans, Tassos Grammatikopoulos, Nicole Hoffmann

"Twin Metals Minnesota LLC, (TMM) has recently completed a prefeasibility study evaluating the development and operation of an underground copper (Cu), nickel (Ni), platinum (Pt), palladium (Pd), and gold (Au) mining project on the Maturi deposit in northeastern Minnesota.The Maturi deposit is a magmatic Cu-Ni-sulphide deposit occurring along the basal contact of the South Kawishiwi intrusion, comprised of heterogeneous troctolites to gabbros forming a tabular body designated the BMZ (basal mineralized zone). These rocks provide the major gangue mineralogy (plagioclase, olivine, and clinopyroxene) with local, minor rock-forming orthopyroxene, biotite, magnetite, and ilmenite. Altered silicates exist within local fracture and/or alteration zones, which are commonly associated with minor faults in the regional area. The Maturi deposit is comprised of four main mineralized zones within the BMZ, referred to as Stage 1, Stage 2 (S2), Stage 3 (S3), and Upper Heterogeneous. Chalcopyrite, cubanite, pentlandite, and pyrrhotite are mainly hosted within the S2 and S3 units, with talnakhite frequently occurring within the S3 unit.A cross-discipline approach combining geology, geochemistry, metallurgy, QEMSCAN™ mineralogy, and mine planning has been implemented to develop a preliminary geometallurgical model and life of mine metallurgical performance forecast. This paper provides an overview of the methods that were used to develop the model and forecast, and discusses the advantages of such a model in project development and evaluation.INTRODUCTIONThe TMM Project proposes mining a copper-nickel-palladium-platinum-gold-silver (Cu-Ni-PGM) magmatic sulphide deposit situated in the Duluth Complex of northeastern Minnesota, USA. The prefeasibility study proposes a 45,000 million tonnes per day mine and concentrator facility to produce two saleable concentrates. The mine will access two separate deposits, Maturi and Maturi Southwest. Saleable concentrates are the final products of the sequential flotation plant where a high grade Cu concentrate is produced followed by a Ni concentrate."

Jan 1, 2015

By Hazel Lyman Nickel

Daring to try where others had failed, Herbert and Lou Henry Hoover translated from the Latin the principal (and first) textbook on the mining and metallurgical profession, De Re Metallica, 1556, which had been in use for two centuries and then had lain dormant for 350 years in a language unreadable except by a chosen few. Thus the Hoovers enriched the English tongue with a vitally important contribution to history in the fields of mining, metallurgy, and chemistry. To them it was a joint hobby, because they were actively interested in the beginnings of the mining profession in which they had both been trained. Illuminating the years of toil to perfect this translation shone their ideal of service to humanity, since, in the Preface, they refer to their task as "a labour of love", which had to find the moments for its execution in night hours, weekends, and holidays, extending over a period of about five years. And they add: "If the work serves to strengthen the traditions of one of the most important and least recognized of the world's professions, we shall be amply repaid". While a student at Stanford University, during the years of 1891-95, Herbert Hoover had become familiar with a copy of this Latin mineralogy classic, De Re Metallica, a rare book in the private library of Dr. John C. Branner, at that time head of the department of geology and mining. Another Stanford student in geology was also examining and studying the ponderous volume of twelve 'books'. She was Miss Lou Henry, of Monterey, who graduated in 1898, and the following year became Mrs. Herbert Hoover. Interwoven through the tapestry of their life experiences gleamed the silver thread of their interest in this mediaeval Latin textbook. Just nine years lacer, the Hoovers had commenced their translation, while they were in temporary residence in London after the seething years in China under the shadow of the Boxer rebellion.

Jan 1, 1949

By C. P. Patel

"The Sturgeon Lake Joint Venture volcanic massive sulpide deposit was discovered in 1970. Milling was started by Falconbridge Copper Ltd. at Sturgeon Lake in September 1974. The Sturgeon Lake pit and mill are located 88 kilometers by road northeast of Ignace, Ontario. IgnE1ce is a town of some 2800 people located on the Trans-Canada Highway, 241 kilometers west-northwest of Thunder Bay. The mill is treating an average of 1100 TPD producing separate concentrates of copper, lead and zinc. Initially, difficulties were experienced in achieving accept-able concentrate grades and recoveries but these were eventually overcome. This presentation describes current metallurgical strategy as practiced at the Sturgeon Lake mill.But first, a few words about the type of ore being treated. In geological terms the ore is classified into two main categories. They are the massive sulphides with underlying zones of stringer sulphides as illustrated in Fig. 1. The plan view is shown in Fig. 2. The areas of East-limb and North-limb are as shown. These last two ores have suffered enough alteration to cause problems during treatment. The massive sulphides consist of chalcopyrite, sphalerite, galena, tetrahedrite and small amounts of pyrrhotite among other gangue materials. The stringer ore is comprised of predominantly chalcopyrite intrusions into rhyolite and has lesser amounts of sphalerite and tetrahedrite. At present we are treating a predetermined blend of massive and stringer ores from zones that have been metallurgically tested to ensure compatibility with current treatment procedure in the plant. Ore responding to this treatment is classified as normal ore while the ore proving incompatible is classified as north-limb ore or east-limb ore."

Jan 1, 1980

By Stuart McTavish

"Noranda's Goldstream mine is a 1,500 ton per day copper-zinc mine located 60 miles north of Revelstoke, B.C.The orebody which contains 3.69% Cu and 2.69% Zn was discovered in 1972. Construction of the mine and mill was completed in 1982 and start up was achieved in May 1983.This paper will describe the flowsheet and related equipment 1n the crusher and mill, in particular the dewatering section where two Larox pressure filters are used to dry the concentrates.INTRODUCTIONThe Goldstrean property is located 60 miles north of Revelstoke, B.C. in the Goldstream River Valley (Figure #1). It was discovered during the construction of a logging road in 1972. Exploratory drilling was initiated in 1975, and in 1976 a portal was collared to obtain underground data. Samples were taken from the underground workings for metallurgical bench tests and a pilot plant run.Due to economic conditions, the decision to go into production was delayed until 1980. Concentrator construction and underground development progressed simultaneously during 1981 and 1982, and were completed by the end of 1982. Start up of the concentrator was achieved on May 2, 1983.The ore typically contains about 40% sulphides, which are chalcopyrite 10%, sphaletite 6%, pyrrhotite 20%, and pyrite less than 5%. The sulphide minerals have a high degree of intergrowth. Most of the sphalerite occurs in micron sized grains which are embedded in the pyrrhotite and, to a lesser degree in the chalcopyrite. There is also some fine dissemination of the chalcopyrite in the pyrrhotite. The waste rock is made up of about 30% quartz, 20% guange silicates, and 10% carbonates. The ore has a specific gravity of 3.2 and a natural pH of 8.2."

Jan 1, 1985

By P. Klossek

It is estimated that China accounts for 94% of the world supply of rare earths (Roskill, 2011). This fact, together with the impact of China?s export policy, poses a substantial risk to the security of the rare earth supply as well as a rare earth price risk. This situation has motivated an increase in the number of rare earth projects under development, i.e., there are currently more than 440 worldwide (Technology Metals Research, 2012). However, economically and environmentally acceptable processing technology to produce tradable products from rare earths (e.g., separated rare earth oxides) is not freely available on the market at the moment. In this respect, a lot of research and development has been initiated on this topic, in academia as well as in industry. Using a proprietary model and scenario-based analysis, we studied the impact that the development of rare earth processing technologies would have on the rare earth market and the economic feasibility of rare earth projects mentioned before. The analysis showed that this impact varies depending on the technology type (e.g., technology can affect project production volume, cost structure or both) and the legal context of the invention (e.g., free or limited by patenting availability of a new technology). The effect of a technology which influences project production volume is not the same as of a technology which changes project cost structure. The impact of a patented processing technology differs from the impact of a processing technology which is freely available on the market. In the case of a new technology which is limited by patenting, its impact depends on the market position (?producing?, ?next-coming?, or ?not producing? project) of the patent holder. The paper contributes to existing research by studying the dependence of the expected micro- and macroeconomic impact of rare earth processing technology developments on the properties of a new technology (e.g., costs, legal framework etc.). By this means, the paper adds to existing knowledge and attempts to make the rare earths market more transparent and predictable from a perspective outside China.

Aug 1, 2013

By C. H. Stockwell

"The Precambrian rocks of southeastern Manitoba contain a great variety of mineral deposits, including gold, chromium, copper, nickel, lithium, tin, beryllium, tungsten, and molybdenum. Although considerable interest has been shown from time to time in each of these types of deposit, production to date has been almost entirely in gold. This has had a value of about $26,000,000 and has been derived chiefly from the San Antonio mine, with lesser amounts from the Central Manitoba, Gunnar, Beresford Lake, Ogama-Rockland, Diana, and other properties.Most of the deposits lie within volcanic and sedimentary rocks or within basic intrusions cutting these rocks. These favourable rocks occur in several areas, which have been given local names and are separated from one another by large bodies of granite (Fig. 1).In general, the several areas are characterized by different types of mineralization. Thus, the Rice Lake-Beresford Lake area contains numerous gold deposits and has yielded almost all the gold production to date; the Maskwa River, Euclid Lake, and Oiseau River areas are, on the whole, characterized by deposits of chromium, copper, nickel, lithium, tin, and beryllium; and in the West Hawk Lake area there are deposits of gold, tungsten, molybdenum, and lithium.As might be expected in a district containing such a variety of mineral deposits, the structural conditions controlling their deposition also vary greatly. It is, accordingly, convenient to discuss the structural geology and mineral deposits of each of the more important areas separately."

Jan 1, 1954

By John G. Henning

The Hoyle Pond underground mine is located in the Porcupine Gold Camp, 18 km east of downtown Timmins. Since the initiation of production in 1985, the operation has produced in excess of 1.9 million ounces of gold at a grade of 15 grams per tonne. Currently, Hoyle Pond ranks 8th in total ounce production for all past and present producing mines in the camp, with the highest head grade of any of the significant past, or present producing mines in Timmins. Cut and fill, shrinkage, longhole and panel mining methods are employed to excavate the narrow gold bearing structures. Using illustrative examples, this paper provides an overview of factors, such as geologic setting, rock mechanics challenges and mine infrastructure, which influence mine design at Hoyle Pond.

Oct 1, 2004

By U. Storck

"Shaft sinking for exploitation of the deep potash beds in Saskatchewan involved great difficulties from the very first because of the need to exclude from the shaft the high-pressure water encountered in the overburden. Control of the troublesome Blairmore quicksands was achieved relatively quickly by use of the freezing method and by lining with cast iron tubbing. The unsolved problem remained, however, of sealing the water-bearing Devonian where the formations had extremely low permeability and were thus hard to grout. Long experience in German potash mines had shown that the permanency of the whole mine would be seriously endangered if large amounts of unsaturated salt water were allowed to flow in from the shaft wall and merely removed by pumping. The prevention of water movement and the resulting dissolution of salt in the overburden were known to be most important. In the Alwinsal shaft, water flow from the Devonian has been prevented by the use of a steel and concrete sandwich lining similar in principle to a kind of lining introduced a few years earlier, and for another reason, in German coal shafts. As its installation is neither more expensive nor more time consuming than that of cast iron tubbing lining, this same lining was also chosen as protection against the Blairmore quicksands. The great advantage of the steel lining, in addition to its relatively high strength, is the fact that it is possible to make the joints of the individual segments absolutely and permanently water-tight by means of tested welds. The virtual dryness of the Alwinsal shaft will also result in lower costs because significant corrosion of all its steel installations, including skips, cage and ropes, will be prevented."

Jan 1, 1968

By M. Rebolledo, N. Mora, G. Zarate

For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Jetti Resources has developed a novel hydrometallurgical alternative to extract metals of value from mineral ores that the mining industry has struggled to process. Jetti’s catalytic technology, whilst being especially advantaged for extracting copper from low-grade and highly refractory minerals, such as chalcopyrite, seamlessly integrates with existing heap leaching methods and downstream processing operations. The technology uses a catalyst which weakens the metal-sulfide bond in the crystalline structure of the chalcopyrite mineral and alters the structure of the passivation layer allowing the leaching process to continue. Metallurgical test work was conducted to examine the effect of ore variability, in terms of grade and copper deportment. The results presented in this study highlight the amenability of the technology and demonstrate that it is possible to enhance leaching performance of copper primary sulfides over a wide range of copper grades, from 0.1 to 2.2%. Further, it is concluded that despite the copper grade, the tests with increasing chalcopyrite content render copper recoveries up to 4 times higher compared to the tests under non-catalyzed conditions. Jetti’s catalytic technology is currently being evaluated at larger scales, namely a commercial dump leach operation and 50-tonne crib tests. The results obtained thus far are compared to the results from conventional sulfide heap leaching tests. INTRODUCTION For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Chalcopyrite (CuFeS2) is the most abundant and recalcitrant of the copper sulfides (Singer, 2017). Owing to its abundance and economic importance, it is the most demandable natural source for copper worldwide. In fact, the projected demand for copper is further expected to rise much higher beyond the current demand by the year 2020 (Panda et al., 2015). Therefore, it becomes imperative to find low intensity hydrometallurgical technologies for the extraction of copper from chalcopyrite in ores of such low-grades that are un-economic to concentrate and to augment the supply by extracting copper from ores with complex mineralogy that cannot be concentrated (Watling, 2013).

Jan 1, 2019

By C. A. Horne

"The transportation of mineral solids in the form of slurry is a subject most of us are associated with and, in fact, live with on a daily basis. The design parameters of slurry systems and most important the prime movers or cent¬rifugal pumps, are frequent and often controversial subjects due to the lack of practical guidelines which, if known and followed, can increase both reli¬ability and service life of the equipment.In this talk, emphasis has been placed on the practical side or rule-of-thumb approach to applications which, in turn, has been related to successful field results. The theoretical content and complex design criteria associated with actual equipment design has consequently been held to a minimum in the following discussions.I. BASIC SLURRY PUMP DESIGN CONSIDERATIONSFirst, to better understand how a centrifugal pump performs work, a basic description of the operating principles are in order.A. Operation In a pump, mechanical energy is transformed into pressure energyby virtue of the centrifugal force exerted by the rotating impeller. The liquid is discharged by centrifugal force at a velocity required to generate a given head and the volute collects the liquid so useful work can be done by the conversion of kinetic energy to pressure energy."

Jan 1, 1976

By J. W. Meier, J. O. Edwards, R. C. Bell

"IntroductionTHE DIE CASTING industry .as we know it today is the direct result of the invention and development of die casting machines during the nineteenth century and of reliable alloys in the twentieth. The early machines were designed to cast low melting point metals such as lead .and tin, and their alloys.It was inevitable that, as these die castings were put into service, the demand should arise for stronger materials. Zinc alloys, often containing lead, tin, copper, and aluminum as major constituents, were relatively easy to cast and stronger than the lead and tin alloys. However, it became apparent after a number of years that these zinc alloys tended to become brittle, distort, and corrode, particularly if kept in warm, humid atmospheres. Thus, considerable quantities of zinc-base .alloys were in use before the trouble was realized and effective measures could .be taken to determine the cause of the instability.The deleterious effect of certain metallic impurities on the properties of zinc •die casting .alloys has now been known for about thirty years. Brauer .and Peirce, and, later, other research workers of the New Jersey Zinc Company such as Anderson and Werley, discovered the pronouned effect of lead, cadmium, and tin on the stability of zinc-alloys."

Jan 1, 1952

By John J. Deutsch

"1T is a great pleasure for me to be present at the Annual Dinner of the C.I.M.; a pleasure which is combined with a mutual opportunity that I value highly. First of all, this occasion gives me a chance to meet again many Members of your Institute and to become more fully informed of the special problems of the mining industry. This alone is ample reason for me to welcome the invitation to join you tonight. In addition, this occasion provides me with an opportunity to tell you something about the work of the Economic Council which might be of particular interest to your industry.In the mining industry, keen competition and constant change are basic facts of life. The continuing prosperity of the Canadian mining industry depends fundamentally on how successfully it is able to adapt both to the changing conditions within the industry and to major trends which operate throughout the world.First of all, the scale and organization of the industry are evolving to new and different dimensions. As one authority has put it, ""The cream of the small high-grade, easy-to-mine ore deposits of this world have been consumed and mining is becoming more and more an industry of very large scale, complex operations. It has already become in most countries a capital intensive industry and its problems, scientific, technical and economic, are growing in difficulty."""

Jan 1, 1966

By Staff

Introduction As the Sherritt Gordon property is still in the development stage, . it is rather difficult to write a proper account of the mining methods and milling practice that will be used. While the general scheme of operation will remain the same, there will undoubtedly be many minor changes to meet special conditions which we cannot forsee at the present time. Most of the work accomplished to date has followed the usual routine of preliminary development in the Canadian North. However, we have learned a few things which might be of use to others operating under similar conditions. The most important of these is the saving in power cost made possible by the use of Diesels as against steam power when using wood fuel, and the movement of freight by tractors when rail transportation is not available. Location The property i6 located about 90 miles north of The Pas, or 40 miles northeast of the Flin Flon mine. A branch line from Cranberry Portage, on the?C. N. railway, between Flin Flon and The Pas, connects the property with the outside.

Jan 1, 1930