Search Documents

By A. D. Walters

"IntroductionScreens are used in coal preparation plants for four basic functions, namely:I. Scalping off large size run-of-mine coal for initial size reduction;2. Sizing of coal treatment in different process streams;3. Removal of magnetite (dense medium) from clean coal and refuse;4. Dewatering.Canadian coal preparation plants use screens extensively in the above functions. Even plants where no beneficiation takes place, screening and crushing are carried out in the size reduction process.Description of Process UnitsThe type of screen used in coal preparation plants generally falls into the following categories:Fixed Screens and Grizzlies (for large coal)Often a simple rugged construction, either set horizontally above a bin or inclined with the coal flow.Fixed Sieves (for fine coal)They are used for dewatering and/ or size separation of slurried coal or discard. The sieve bend, the Vor-Siv, the Wilmot riffle and the cross flow screen fall into this category. The most commonly used in coal preparation plants is the sieve bend, Figure 1. Coal slurry is fed tangentially onto a fixed curve wedge wire screen deck. The solids are separated at a predetermined particle size, delivering a partially dewatered overproduct and a dilute underflow. The coal slurry is initially delivered to the sieve bend via a feed box. A series of baffles spreads the feed evenly across the width of the deck. The slurry drops from the last baffle, passes through the feed spout and is fed tangentially to the screen. It is important that the feed should contact the surface immediately at the front end of the sieve bend. It is possible to lose as much as 250Jo of screening area with a poorly fitted screen box.The full stream of coal slurry flowing over the sieve bend decreases in depth, in increments of approximately •;4 the slot width each time it passes a slot. Sieve bends make a size separation at 112 to 2h the slot width. This feature virtually eliminates blinding of the screen surface. Slot sizes are normally quoted in millimetres, available standard slot sizes are from 2 mm to 0.125 mm. The sieve bend is also widely used in coal preparation for preliminary dewatering."

Jan 1, 1989

By Norman Marr

Introduction In Canada, the mining industry and water-power development are intimately associated in that mining, which ranks second among the country's primary industries, depends principally upon hydro-electric energy for its large power requirements. On the whole, the Dominion has been very favourably endowed with water-power resources; generally speaking it is a well-watered country with numerous rivers and lakes located in are as where the topography favours water-power development. Precipitation, the raw material of water power, varies from an annual fall of more than l00 inches on the Pacific coast to about 12 inches in sections of the Prairies and the Northwest Territories; in Ontario and Quebec the annual average is 24 to 40 inches and in Nova Scotia about 45 inches. In its descent to the sea, the resulting run-off, much of it from considerable altitudes, creates sources of potential energy at every rapid and fall along the country's many streams and rivers. Many of the innumerable lakes in the Dominion provide storage basins for the regulation of stream flow, thus enhancing the potential power of available sites. While water-power resources are fairly well distributed across the Dominion, as is shown on the accompanying map of Canada showing power sites (Figure 1), it is particularly fortunate that those areas which are lacking in indigenous fuels have been compensated in large degree for this scarcity by being favoured with a high proportion of the total potential water power. This has an important bearing on the mining industry in that extensive mining operations can be economically carried out in the great Canadian Shield, which is lacking in commercial coal deposits but is rich in water-power resources. This Precambrian formation, which forms a wide belt around Hudson bay and in which many metalliferous ores are found, was 'subject to severe glaciation in a recent geological period, so that its river systems are comparatively young and are characterized by numerous lakes joined by short reaches of fast water, rapids, and falls which offer frequent opportunities for power development. The western Cordilleran region, which also is important in mining, has abundant water power. The accompanying geological map (Figure 2), prepared by the Geological Survey of Canada, shows the great extent of the Precambrian and Cordilleran regions and may be compared with the map of water-power sites to show the high incidence of water-power resources in these potential mining areas in which important mineral discoveries have already been made.

Jan 1, 1949

By J. B. Hinzer, J. D. Harvey

"Noranda's Lyon Lake property in the Sturgeon Lake area of Northwestern Ontario was staked by Mattagami Lake Mines Limited in May 1969 to cover airborne Input anomalies. Subsequent ground geophysical and diamond drilling programs resulted in the disco very of the Boundary Extension, Lake and Creek ore zones. As of December 31, 1978, ore reserves were estimated at 3,945,000 tons assaying 6.53 per cent Zn, 1.24 per cent Cu, 0.63 per cent Pb, 3.42 oz/ton Ag and 0.010 oz/ton Au.These deposits are hosted within the South Sturgeon Lake volcanic pile of Archean age, which consists of several cycles of basic intermediate and felsic volcanic materials overlain by a sedimentary iron formation and built upon a plutonic base (Franklin , ' 1975). The top 50 m of the second felsic cycle, according to mine terminolo gy, contains the mineralization within Quartzphenocryst- bearing felsic lapilli tuff and underlying thin discontinuous graphitic sediments and altered coarse pyroclastics. The basal andesitic member of the overlying cycle forms the hanging wall to the ore deposits.Although there is no alteration pipe below the deposits, the coarse footwall rocks are permeated by chlorite, garnet, carbonate, iron sulphide and magnetitie-bearing veins intensifying from west to east.Immediate host rocks are alkali depleted and MnO, FeO, Zn and Cu enriched compared to Goodwin's (1972) average Archean rhyolites. Bedded pyrite-pyrrhotite-chalcopyrite lenses with sphalerite-rich tops are underlain by weakly developed stringer mineralization.Traversing eastward from the Lake Zone to the Creek Zone and toward the Sturgeon Lake Mine deposit, more rapid facies changes, more pronounced chloritic and carbonate alteration, the presence ofgarnets, greater MnO, FeO, CaO and Ag abundances, and increasing Zn/Cu and MnO/FeO ratios are apparent."

Jan 1, 1981

By Charles Amoah

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By Michael Moser, Brighty Dutta, David Dreisinger

"Molybdenum is widely used in the industries as an alloying element in the manufacture of steels and super alloys. The widespread use of the element encourages a growing need to develop extraction processes for recovery from both primary and secondary sources. The Solvay Group has developed a solvent extraction reagent named CYANEX®600 for the recovery of molybdenum from acidic solutions originating from both low grade (e.g. copper solvent extraction raffinates, smelter dusts and slags) and high grade (molybdenite) molybdenum sources. CYANEX®600 is a purified form of CYANEX®272 with the active component bis(2,4,4- trimethylpentyl)phosphinic acid. The extraction behavior of CYANEX®600 towards molybdenum in sulphuric acid medium was evaluated. The uptake of molybdenum increased with the increase in concentration of CYANEX®600. The approximate stoichiometry of the extracted complex was: Mo: CYANEX®600 = 1:2. Efficient back-extraction could be achieved with 0.1 M disodium EDTA and 0.1 M (NH4)2CO3, thus providing the option of recyclability of the extractant. The detailed back-extraction studies are currently under progress to find out the possible option for complete transfer of Mo(VI) to the aqueous phase so that high purity Mo salts could be precipitated from the molybdate solutions.INTRODUCTION Molybdenum (Mo) is one of the world’s valuable metals and is highly sought after by researchers due to its versatile mechanical, thermal, chemical properties. Swedish scientist Carl Wilhelm Scheele demonstrated molybdenite to be a mineral sulfide in 1778. Peter Hjelm successfully isolated dark metal powder from the mineral sulphide and named it as ‘Molybdenum’ in 1782 (Gupta, 1992). Molybdenum is a refractory metal of silver gray appearance and is an important alloying element used in the manufacture of steels and super alloys. Molybdenum compounds are widely used in formulation of catalysts (Gupta, 1992). Molybdenum occurs in nature only in chemical combination with other elements. Several molybdenum bearing minerals have been identified, but the only one of commercial significance is molybdenite (MoS2). As molybdenum is a strategic metal for the industrial sector, its widespread use acts as a factor for depletion of the natural resources. Hence, there is growing need to develop extraction procedures for its recovery from both primary and secondary sources. United States, China, Chile, Canada, Peru, and Mexico are listed as the main producers by the U.S. Geological Survey, 2016 (U.S. Geological Survey, Mineral Commodity Summaries, January 2016)."

Jan 1, 2017

By L. Larson

Rock samples were taken, away from zones of mineralization , from seven sections of five rhyolitic zones as define d by Spence (l967) in the Noranda area. The purpose of the investigation was to test whether there were intrinsic differences between the zones which would differentiate between non-productive zones and productive zones. For the elements sought (major elements, Cu , Pb , Zn and S) , no clear chemical difference between the zones was found. Thus, identification of a favour able zone from the over -all composition of the zone does not appear promising. Within sampled sections, there is no clear gradual compositional change up through the sections. A capping of highly siliceous massive rhyolite is present in five of the sections sampled. A layer of relatively basic material occurs near the base of individual units. The third (mine zone) and later zones contain abundant pyroclastic material, where as the non-productive zones do not.

Jan 1, 1977

By A. M. Childs, R. F. Mather, K. R. Rawling

"The challenges encountered in the design and construction of mines and their process facilities today are becoming more intense and the engineering more competitive. The need to incorporate new techno1ogy to compensate for ever rising costs is always present, but its application in the harsh environment of Northern Canada increasingly requires the inclusion of new proven methods and innovative approaches to arrive at economically attractive projects.This paper deals with the development of the process design for the Cullaton Lake Gold Mine in the Northwest Territories. Particular emphasis is given to the interaction of the imposed construction and testwork schedules, and their effect on certain process decisions.The challenge that faced the project team may be defined by the following factors:1. A schedule which required that metallurgical testing, engineering, and procurement and delivery of all equipment and construction supplies should be complete within a period of ten months.2. Transportation of all personnel, equipment and supplies to the site by airlift, as no road was available or affordable.3. A six week period when transportation to the site was impossible.4. The extremes of temperature beyond the tree line in the Northwest Territories.5. A complete lack of infrastructure in the area."

Jan 1, 1983

By P. D. Hodgson, G. L. Kelly, H. Beladi

"The formation of ultrafine ferrite by strain induced transformation is assessed using rolling and hot torsion experiments. These experiments are used to examine the impact of thermomechanical processing conditions and steel chemistry on strain induced austenite to ferrite transformation and the formation of ultrafine ferrite. The critical strain for dynamic strain induced transformation increased with increasing carbon equivalence, deformation temperature and austenite grain size. The deformation structure in the austenite grains changes with the thermomechanical processing conditions.Drawing on these results and the current literature, the important factors for the production of ultrafine ferrite are described and a mechanism proposed."

Jan 1, 2004

By N. Katsikaros, A. Lewis-Gray, P. Richards

"To optimize gold recovery in complex leach-to-electrowinning processes, Gekko Systems developed the Gekko resin exchange column (G-REX) as an intermediate step, using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin. Operational experience has been gained at the Castlemaine Goldfields Ballarat gold mine. In near-continuous operation since 2008, the Ballarat plant treats unclarified concentrate leach solution. The extension of this technology to higher throughputs and more complex chemistry is discussed.RÉSUMÉ Afin d’optimiser la récupération de l’or dans des procédés complexes impliquant la lixiviation suivie de l’extraction électrolytique, Gekko Systems a développé la colonne Gekko de résines échangeuses d’ions (G-REX) comme étape intermédiaire, à l’aide d’une résine hautement sélective pour la récupération de l’or qui permet d’isoler les métaux contaminants. Gekko détient la licence exclusive pour la résine AuRIX®100 produite par Purolite, et la colonne G-REX a été spécifiquement conçue pour cette résine. C’est à la mine d’or Ballarat de Castlemaine Goldfields que l’expérience opérationnelle a été acquise. L’usine de Ballarat, en exploitation quasi-continue depuis 2008, traite une solution concentrée non clarifiée de lixiviation. L’extension de cette technologie à des capacités supérieures et à une chimie plus complexe est examinée.AURIX®100 RESINAuRIX100 resin is a crosslinked polystyrene alkaline resin developed by Henkel (Virnig, Mackenzie, & Adamson, 1996). The resin beads are off-white in colour and spherical, with a nominal size of 100% +600 µm. This resin is highly selective for gold and silver over many metals, by way of extracting precious metal–cyanide complexes from leach solutions with a pH of less than 11.5. The higher end of the pH scale produces the best selectivity according to the order of preference: Au > Ag > Hg > Zn > Ni > Cu > Co > Fe. Purolite produces the resin and Gekko Systems maintains licensing of AuRIX100 resin for use in its G-REX column, as part of its unique suite of gravity gold–handling equipment.Significant cost savings over carbon-in-solution (CIS) systems are realized with AURIX100 resin: approximately 4–12% in capital savings and 27–40% in operating costs (Virnig, Mackenzie, Katsikaros, & Gray, 2004). Additionally, AuRIX100 resin is not susceptible to fouling; that is, the resin does not load with inorganic salts or organic compounds that would affect the loading and extraction of precious metals. To counter any potential for fouling by inorganic salts, a dilute acid wash is periodically conducted in service on the resin to unblock resin pores."

Jan 1, 2017

By Marie-France Caille, Carl Caumartin

"Audrey Resources' Mobrun Mine is located in Dufresnoy Township some 30 km to the northeast of Rouyn-Noranda. The Mobrun tine deposits consist of two major massive sulphide lenses; the newly discovered 1100 lens located 450 m south of the Main zone, and one ntellite lens, the 850-870-930 complex.The 1100 lens is hosted in a large pyroclastic unit bounded to the mouth by rhyolite and andesite flows and by a thick rhyolite unit to the art h. stratigraphically belon the three lenses. It consists of approximately 15 Mt of massive sulphide, of which 10.4 Mt are of economic ade. The Main lens lies comformably above thick rhyolite flows, ecciated and pyritized by the sulphide horizon, and is overlain by ttercalated ash tuffs and rhyolites which host the over-lying satellite ns. The Main lens consists of 3,3 Mt of massive sulphide, of which 523 000 tgrade0.80% Cu, 2.44%Zn,30.19 g/t Ag, and2.2 g/t Au he richer satellite lens (180 000 t) is part of the same volcanic stem and resulted from a resurgence of hydrothermal activity. ructure played a role in the final geometry of the deposits but did not eatly affect the volcanogenic and stratabound nature of the lens. Total production since the start of operations in 1985 amounts to 58 000 t and is restricted to the Main lens. Production from the 100 will come onstream in 1992 as ore reserves from the Main and e satellite lenses are exhausted.RESUMELa Mine Mobrun de Ressources Audrey inc. est située dans le mton Dufresnoy, a quelque 30 km au nord-est de Rouyn-Noranda. lle comprend deux lentilles de sulfures massifs d’importance majeure ~i sont les lentilles 1100 et Principale, et une lentille satellite qui est complexe 850-870-930.La lentille 1100, la plus ancienne, est contenue dans une épaisse 1ite pyroclastique bordée, au sud, par des coulées de rhyolite et d’andésites, au nord, par une épaisse unité rhyolitique. Cette lentille contient environ 15 Mt de sulfures massifs dont 10,4 Mt à teneur économique. La lentille Principale repose sur d’épaisses coulées rhyolitiques brechifiees et pyritisees à proximité de l’horizon de sulfures; elle est recouverte de tufs a cendres et de rhyolites interlitees qui contiennent la lentille satellite. La lentille Principale est constitute de 3,3 M t de sulfures massifs dont 1 523 000 t sont économiques avec une teneur moyenne de 0,80% Cu, 2,44% Zn, 30,19 g/t Ag, et 2,2 glt Au. Faisant partie de ce second épisode volcanique, la riche lentille satellite (180 000 t) temoigne d’une recrudescence de l’activité hydrothermale. La structure joue un rôle important dans la géométrie finale des dépôts mais ellen' affecte pas, de fa~on significative, la nature volcan génique des lentilles. Depuis le début des opérations, en 1985, la production totale est d’environ 568 000 t, provenant essentiellement de la lentille Principale. La mise en production de la lentille 1100 est prévue pour 1992, alors que les réserves des lentilles Principale et Satellite seront probablement épuisés."

Jan 1, 1990

By The Staff

"THE Wabana iron ore mines, owned and operated by the Dominion Steel and Coal Corporation, Limited, .are on Bell Island in Conception bay, on the east coast of Newfoundland. Mining began on surface in 1895 and, although open-pit work is still done on a small scale, the entire output may be considered to•be derived from extensive submarine workings. In 1958 the average daily production of hematite ore was close to 12,000 tons, almost all of which was concentrated in a heavy-media plant. SUMMARYThe character, occurrence, and extent of the submarine bedded deposits enabled early operators to meet prevailing market demands with the minimum attention paid to exploration. Mechanization of the mine and the pressure for sustained high tonnages since 1955 have emphasized the importance of an expanded exploration and development programme.A serious handicap has been the impossibility of utilizing normal diamond drilling methods to explore ore conditions in advance of mining faces. Drilling between tl1e bedded zones has been done but the major difficulty has been to delineate ore reserves in the lower bed, which has the greatest ore potential of the three mineable seams."

Jan 1, 1960

By F. J. Alcock

IN the summer of 1934, gold was discovered on Lodge bay, on the north shore of lake Athabaska in northern Saskatchewan, about fifty miles east of the Alberta boundary line. The first claims were taken up by the Consolidated Mining and Smelting Company of Canada, Limited, and there was a 'rush' to locate similar showings. Staking continued through the summer and succeeding winter, and in the spring of 1935 the provincial government established a recording office at a convenient point which is central to the more important holdings and where 'planes can land in any weather. During the past summer, the name of this townsite was changed from Beaverlodge to Goldfields, and a post office was established here. The season was one of great activity; a great deal of assessment and development work was carried out and a large amount of further prospecting done. In addition to the work by private companies, geological investigation was carried out in the region by a Federal Geological Survey party under the charge of the writer and a reconnaissance examination was made of an area of some 7,000 square miles surrounding the region of particular interest. Though this was the first discovery of gold in the region it was not the first occasion that prospecting had been carried out along the north side of lake Athabaska. Over twenty years ago, a number of prospectors were at work in the area and a large number of claims were staked, many of which were never recorded. One man by the name of Piché, in the years 1910, 1912, and 1913, took up a considerable number of claims north of Pine Channel narrows, east of Fond du Lac. His discoveries, which consisted of small showings of sulphides in sedimentary gneiss, proved to be of no economic importance. In 1915, a sudden widespread interest was aroused by the report that a sample of ore collected near Fond du Lac had yielded a very high assay in silver. In March and April of that year, prospectors began to rush into the field by dog teams to take up claims, and, as soon as the Athabaska river was free of ice, others started by boat from Athabaska Landing. Some hundreds of claims were staked and recorded in the Dominion Land Office at Edmonton or at Fort Smith. By July, most of the prospectors had? left the region, having failed to find any silver ore. In 1921, considerable prominence was given to the area a few miles east of Goldfields by reports that very large masses of iron ore were available there. Claims were taken up, but the material is much too low grade to be considered commercial ore.

Jan 1, 1936

By Lex L. Udy

External-detonation-generated plasmas, highly ionized zones of reacting material ejected from the surface of detonating explosive charges, are shown to be the cause of channel desensitization, i.e., the self-quenching of a detonating explosive column loaded in a borehole with an air annulus between the explosive and the borehole wall. The effects of this phenomenon on several explosive compositions and types are demonstrated and discussed. The explosives tested include aluminum-sensitized and explosive-sensitized slurries, ANFO, liquid explosives and dynamites. Various techniques are described that can be used to reduce or eliminate the plasma effect.

Jan 1, 1979

By H. M. Kim, J. Rutqvist, D. W. Ryu

"Demand of high pressurized gas storage in underground rock caverns is increasing. Compressed natural gas (CNG) and compressed air energy storage (CAES) are one of the promising examples after since lined rock cavern (LRC) concept has been verified through in-situ pilot tests. Two key essential concerns of high pressured gas storage in underground rock caverns are mechanical stability of the cavern against high inner storage pressure and the risk of gas leakage from the caverns.In this study, we introduce our results of numerical simulations so as to investigate the potential of monitoring for gas leakage at a pilot facility for CAES in underground LRCs. The pilot facility was constructed at a comparatively shallow depth of 100 m, compared to the previous cases with several hundreds of meters, aiming at validating the feasibility of the LRC storage concept in which inner sealing liners, consisting of steel plate and concrete linings, are installed inside the excavated rock caverns (KIGAM, 2011). Compressed air may leak through either initial defects of inner containment liners such as imperfect welding regions and in-situ construction joints of the liners, or through structurally damaged points of the liners during the CAES operation where compression and decompression of the caverns are necessarily repeated and their structural robustness can be deteriorated.For this perspective, we carried out a coupled thermodynamic and geomechanical deformation analysis using TOUGH-FLAC simulator, and investigated the effectiveness of strain monitoring method in detecting mechanical failure of liners which may provide major pathways of air leakage. We therefore used an equivalent continuum model to relate the localized tangential strain to fracture permeability changes, which was developed in our early work (Rutqvist et al, 2012). In detecting and characterizing the leakage location, we tested a cross correlation technique using the synthetic pressure responses monitored in case of the failure of the inner liners. From the investigations, we showed that tangential strain, rather than radial, monitoring especially at the inner face of the sealing liners can be more effective in detecting the mechanical failure of the liners.In localizing the leakage point, we noted that the interface between the inner liners and surrounding rock may not be perfectly bonded so as to increase permeability through which any leaking air pressure may migrate more dominantly. We also demonstrated that the cross correlation of the time histories of pressure measurement especially at these interfaces can be useful in identifying the leakage point. These results may provide useful information in overall design of monitoring and alarming system of our upcoming CAES pilot facilities."

Jan 1, 2015

By C. Larsen, E. Goodwin, E. Konigsmann

"This paper describes the development of an innovative effluent treatment process for cyanide and heavy metal removal from tailings wastewaters at Hemlo Gold Mines Inc. Golden Giant operation.The importance of minimizing dissolution of contaminants in the gold leaching circuit is discussed, as well as using recycled water in milling circuits to the fullest extent possible. Finally, a brief description of the role of natural cyanide degradation in the tailings pond is provided.Emphasis is placed on the need for overall water quality management to ensure minimum effluent treatment process costs and complexity while producing excellent quality effluents.1.0 INTRODUCTIONHemlo Gold Mines Inc. owns and operates its Golden Giant Mine located forty kilometres east of Marathon, Ontario. The Golden Giant mine is one of three gold operations exploiting the large gold orebody located in the Hemlo area. The milling facilities include two stage secondary crushing, three stage, closed circuit ball mill grinding with no reagents, thickening, cyanide leaching and carbon in pulp gold recovery unit operations. The average throughput is 3000 tonnes per day of 10 grammes per tonne gold ore. Figure 1.1 shows a schematic flowsheet of the operation."

Jan 1, 1989

By H. C. Gunning

SOME small vanadium-bearing deposits on the west coast of British Columbia about 100 miles north of Vancouver are of interest for several reasons. They are of a type that is, so far as we know, unique. They are difficult to identify as being vanadiferous so that, unless they are described, other similar deposits could easily pass unrecognized. Furthermore, although none of them has as yet been proven to be of commercial proportions, no good reason is apparent why larger, and therefore valuable, deposits should not occur under similar geological conditions. The original discovery on Quadra island was made in 1932 and has been recorded by H. V. Ellsworth and H. C. Gunning (l). Since 1932, prospecting in the area has revealed other similar deposits, one about a mile south of the original and another some ten miles to the east, near Menzies bay on Vancouver island. The Quadra Island showings are a mile and a half north of the head of Gowland harbour, a small inlet that is easily reached by gas boat from Campbell river, about four miles to the southeast on Vancouver island. The deposits were examined by the writers in the spring of 1943 in connection with field work sponsored by the Department of Geology, University of British Columbia. We are indebted to Mr. G. A. Dirom and Mr. Lothrop, of Vancouver, for helpful data on the Menzies Bay deposits, and to Dr. V. Dolmage for making a brief trip to Gowland harbour and discussing the deposits.

Jan 1, 1944

By James Kear, Romain Prioul, Robert G. Jeffrey, Andrew P. Bunger, Dimitry Chuprakov

"Unconventional gas and geothermal reservoirs are typically naturally fractured and therefore the challenging problem of hydraulic fracture (HF) growth through naturally fractured rocks is an important issue especially for the development of accurate predictive HF models. This paper presents results from laboratory experiments in which HFs have been created in both sandstone and crystalline (gabbronorite) rock specimens such that they impinge either orthogonally or at an oblique angle on an unbonded, machined frictional interface. Depending on the conditions of each experiment, the fractures either cross or are blunted at the interface. The growth behavior was ascertained for these experiments based on a synthesis of the injection pressure record, active ultrasound monitoring, and direct post-experiment inspection of fractured specimens. From these experiments we observe: 1) A contrast between direct crossing and crossing with an offset for orthogonal and oblique intersection, respectively, 2) Apparent independence of crossing/blunting behavior on the friction coefficient for orthogonal intersection, 3) Dependence of the stresses required to promote crossing on the intersection angle between the HF and NF, 4) Existence of cases in which the hydraulic fracture crosses but then essentially ceases propagation such that all fluid is diverted to the interface. INTRODUCTIONHydraulic fracturing is a vital technology used to increase the productivity of oil, gas, and geothermal wells. Predicting hydraulic fracture (HF) growth is, in turn, critical to design of hydraulic fractures that grow to the desired length, accept the desired amount of proppant, and remain contained in the reservoir without unwanted height growth into surrounding layers (e.g. Economides and Nolte, 2000). The importance of HF modeling has prompted 6 decades of research during which simulators have become more efficient, more accurate, and have addressed a growing range of complexities (see review of e.g. Adachi et al., 2007).One of these complexities is the interaction between HFs and mechanical discontinuities such as natural fractures (NFs). Efforts in this area have been mainly driven by development of unconventional (i.e. low permeability) oil and gas resources because essentially all viable low permeability reservoirs, including shale gas/oil reservoirs, are naturally fractured to some degree (King, 2010). One of the most important questions for developing effective HF stimulation strategies in these reservoirs is whether the hydraulic fracture(s) is/are expected to be single-stranded or whether interaction with the NFs will lead to network-like growth. The basic building block for numerical simulators that can address this question (such as Kresse et al., 2013 and Weng et al., 2014) is whether an HF that intersects an NF will cross the NF or whether its growth will be captured by the NF so that additional fluid injection pressurizes the NF but does not generate ongoing growth of a new HF. These scenarios, including subcategories such as crossing with an offset, have been recognized for several decades (Daneshy, 1974; Warpinski and Teufel, 1987, and as recently reviewed and expanded by Chuprakov et al., 2013)."

Jan 1, 2015

By E. S. Moore

Introduction The geology of the Sudbury nickel field has been studied extensively, but there are few reports dealing with the structure of the interior of the basin. It was not until the Treadwell-Yukon zinc-lead deposits were discovered that attention was strongly directed toward the large-scale faulting that has split the basin parallel to its long axis. This faulting has been responsible for the , ore deposits in the basin and it may be regarded in many ways as the most important geological event, next to the intrusion and differentiation of the nickel eruptive sheet, that has occurred in the Sudbury region. The early reports on the nickel region by Bell, and Barlow, were chiefly concerned with the nickel-copper ores and with the formations of the region. Coleman was the first geologist to map the nickel eruptive as a continuous sheet around the belt and to emphasize its basin character. On the map accompanying his later report, he shows an important offset in the nickel eruptive at its southwest end, where the large fault cuts this portion of the basin, but the fault was not traced into its interior, as little detailed work was clone in the basin at that time. No ore-bodies had been developed outside of the nickel-copper deposits associated with the norite when the map was prepared, and attention was mostly concentrated on the nickel eruptive. Coleman did, however, map and name the various formations found within the basin and, in general, his delineation of these has remained the standard for prospectors and other workers in the field until the present day.

Jan 1, 1930

By J. Jin, J. D. Miller

"Bubble attachment at hydrophobic surfaces is of critical importance in the flotation recovery of mineral resources and fundamental experimental results have been reported in the literature describing the details of film thinning, rupture, and displacement. Now, for the first time, bubble attachment phenomena are examined using Molecular Dynamics Simulations (MDS). The simulation involves a nitrogen bubble containing 906 nitrogen molecules in a water phase with 74,000 water molecules at the hydrophobic molybdenite (001) surface. During the simulation period of 1 ns, film rupture occurs and the nitrogen bubble attaches to the molybdenite (001) surface, resulting in a contact angle of about 90o. In contrast, the film is stable at the hydrophilic quartz (001) surface and the bubble does not attach. Contact angles, determined from MD simulation after stabilization of the three phase line of contact, are reported and these results agree well with experimental and MDS sessile drop results. In this way, film stability and bubble attachment are described with respect to interfacial water structure for surfaces of different polarity. For example, the interfacial water molecules for the hydrophobic molybdenite (001) surface have relatively weak interactions with the surface when compared to the hydrophilic quartz (001) surface, as revealed bythe presence of a 3 A water exclusion zone at the molybdenite/water interface. INTRODUCTIONAttachment of air bubbles to mineral particles is of fundamental importance in understanding flotation separation phenomena. It is well known that attachment of an air bubble at a hydrophobic surface includes film thinning, film rupture, and film displacement (Somasundaran, 2006; Wilson, Adlard, Cooke, & Poole, 2000). Experimental techniques, such as high speed video, can catch the process of bubble attachment at a mineral surface (Drelich & Miller, 2012; Niecikowska, Krasowska, Ralston, & Malysa, 2012). However, molecular scale information to examine the phenomena has not yet been reported."

Jan 1, 2016

By A. S. Nortjé

At South Deep Gold Mine longhole stopes are backfilled using a cemented Cyclone Classified Tailings in its hydraulic state. The need to contain the hydraulic fill until cured requires a barricade. Due to the massive size of the stopes, the tailings can exert enormous forces on any such barricade. Barricades have long been in use, but recent failures in Australia and the large rate of filling required at South Deep solicited a robust design. A robust design must examine all foreseeable failures and the barricade must be able to resist all expected and, within limits, unexpected loads. The design should also be simple to construct and cost effective, limiting the impact of construction errors and unnecessary delays to production.

May 1, 2007