Search Documents

By Nordau R. Goodman

"IntroductionTHE HISTORY of Nova Scotia's gypsum industry goes back about two hundred years. The extensive deposits found in the Windsor formation, which is Lower Carboniferous, were the first discovered in North America and were known to the earliest .settlers. There has been a steady increase in production from these beds, except for minor setbacks in years of wars and depressions, but at the same time there has been a decrease in the number of operating quarries. This decrease reflects the change from the days of horse-and-cart recovery to the modern, large-scale, highly mechanized operations. In the beginning, almost any outcrop could •supply the tonnage requirements and the most •convenient were selected, but the millions of tons needed to meet present-day needs are not easily found.Despite the size and importance of the Nova Scotian deposits there has been little detailed geological work. Sir Charles Lyell, in 1843 ( 10), established that the beds are Lower Carboniferous and this was confirmed by Sir William Dawson (3) a .few years later. Both Lyell and Dawson agreed the calcium sulphate beds were an original part of a bedded series .but did not consider they resulted from a concentration of sea water. Lyell reached the conclusion that the gypsum was related to volcanic action in the form of heated vapours or hot springs. Dawson believed it was formed by the action •of sulphuric acid on calcium carbonate. The acid, derived from the oxidation •of iron pyrites which was abundant in the older formations, was carried by rivers into basins which were rich in shells."

Jan 1, 1954

By W. D. Freeborn

Slim-hole drilling and completion techniques were first used in the Cynthia area of the Pembina field, Alberta, by the Texaco Exploration Company in the summer of 1957. Prior to that time, eighty-eight wells had been drilled and completed in this area in a conventional manner. Subsequent to the initial four-well evaluation programme, twenty-one additional wells have been drilled using slim-hole techniques. No difficulty was encountered in the drilling and completion of slim-hole wells, or in obtaining production from them. A comparison of drilling and completion economics and practices has been made for slim-hole and conventionally completed wells. Penetration rates for both bit sizes (614 in. and 9 in.) were relatively equal. The shorter life of the smaller bits required the use of 15 per cent more bits per well, but the total trip time to change bits was similar for both hole sizes because of the higher hoisting speeds possible with the lighter drilling strings used in the slim holes and better hole conditions. Completion costs of the slim holes were reduced by 37 per cent as compared to the costs of conventional-type completions. This was made possible through the use of smaller well equipment, the elimination of tubing, and a reduction in rig time for completion operations.

Jan 1, 1958

This paper presents a case study where Cenozoic age detritals and an ancient buried landslide have been modelled in the final walls of an iron ore pit. Orebody 25 is located in Western Australia’s Pilbara region and is an operating pit where a redesign of the final wall cutback was required. The existing slope design utilised a simplistic geological model of mixed conglomeratic, calcretic and clay –dominated detritals overlying deformed bedrock sequences. This simplicity resulted in a conservative design that was not reflective of the slopes performance to that point. Further field investigation was carried out with the results assessed in conjunction with historic drilling, mapping and laboratory testing. A detailed geotechnical model was developed including three conglomerate and two clay dominated units and laterstage calcrete overprinting. The clay units were of significant importance to the stability assessment and resulting slope design due to the thickness and poor strength conditions indicated by the laboratory and field testing. However, the drilling investigation shed only limited understanding as to the origin of the clays and thereby how they should be treated as a component in the stability analysis. A comparison of the ratio of various geochemical elements measured by assay was made between the clays and 1) shale bedrock and 2) clays of known detrital origin from other nearby sites. This indicated the clays had a strong affinity with weathered bedrock. This and other textural features resulted in the interpretation that the clay units were relic debris preserved following ancient landslides in bedrock shale. Using laboratory testing data and calibration of results for a landslide origin, stability analyses were run, resulting in a steeper slope design being implemented. Excavation of the final cutback is now in progress with the model confirmed as appropriate.

Jan 1, 2015

By J. P. Wiser

THIS paper discusses testing and quality control of milled asbestos fibre. It has been composed with the intention of: (I) Summarizing past, present and probable future methods of testing and classifying the various grades of commercial asbestos produced by the Quebec asbestos industry. (2) Acquainting those unfamiliar with the methods used for evaluating, testing and controlling the grading and the quality of Quebec chrysotile asbestos fibres with some of the physical and chemical procedures currently used for that purpose. (3) Discussing some of the complications facing the producers, such as variations in the orebody and special requirements of asbestos manufacturers. ( 4) Detailing some of the present quality control methods. SUMMARY OF PAST, PRESENT AND PROBABLE FUTURE TESTING METHODS Past During the first years of production of commercial asbestos in the Province of Quebec, fibre testing and quality control were based principally on dry screen analysis and visual inspection. These methods were gradually expanded during the period from 18, 90 to 1932. In 1932, standardization

Jan 1, 1962

By Roger J. Goodman, Don Riva

"IntroductionCrows Nest Resources Limited (CNRL), a wholly-owned subsidiary of Shell Canada Resources Limited, is nearing completion of its first coal project, located in southeastern British Columbia. CNRL shipped over 700,000 tonnes of thermal coal to foreign markets in 1982. With the completion of the metallurgical coal plant in December, 1982, shipments of both thermal and metallurgical coal will increase substantially in 1983 and will approach the anticipated operating capacity of 3.0 million tonnes in 1985. The Line Creek Mine lies some 25 kilometres north of Sparwood in southeast British Columbia (Fig. 1). The open-pit mine is located on top of Line Creek Ridge, with coal being hauled 16 km to the thermal and metallurgical coal preparation plants, situated adjacent to the already existing Canadian Pacific Railway. Most of the coal is moved by 108 car unit trains by CP Rail to coal ports in Vancouver, where it is loaded onto vessels destined for overseas markets. Some smaller scale car load shipments are moved by rail to contiguous markets in the Pacific Northwest. History The southeastern British Columbia area, known as the East Kootenays, is steeped in a rich coal mining heritage, dating back to the latter part of the nineteenth century. Predecessors of Crows Nest Resources Limited were instrumental in developing the rich coal reserves in the area. In 1887, William Fernie, a pioneer-cum-prospector recognized the potential of coal deposits in the East Kootenays. Spurred by the relentless push west of the Canadian Pacific Railway through the Crows Nest Pass area, Fernie recognized that it was just a matter of time before the steam locomotives provided him with his required market. That time arrived in 1897 when Fernie helped to form the Crows Nest Pass Coal Company and coal mining commenced at Coal Creek, near his namesake town of Fernie. During its almost 70-year history, this company produced over 48 million tonnes of steam coal and 8 million tonnes of coking coal. In 1965, the Crows Nest Pass Coal Company was re-named Crows Nest Industries, to better reflect its expanded interests into forest products, and it is the latter company which Shell Canada Resources Limited acquired in 1978. The extensive coal resources of Shell, in both Alberta and British Columbia, were rationalized into one group with the birth of Crows Nest Resources Limited to manage and develop the coal holdings."

Jan 1, 1985

By J. S. Roper

"IntroductionSNOW LAKE is situated in northern Manitoba at latitude 54° 55 and longitude 100°, 400 miles northwesterly of Winnipeg, 80 miles northeast of The Pas, 80 miles east of Flin Flon. A 38-mile road from Wekusko, on the Hudson's Bay railway, serves the community.The mine is located in and close to the southern edge of the Precambrian Shield in typical low-relief muskeg and lake country.The Howe Sound Exploration Company, Limited optioned the property from Nor Acme Gold Mines, Limited, after preliminary diamond drilling had outlined two orebodies of low-grade arsenical gold ore.Following the examination and study of geological data and of 50,000 feet of diamond-drill core, and metallurgical tests made during 1942 to 1945, a decision was made to develop the mine and build a 2 ,000-ton mill concurrently. This development has been described by G. C. Lipsey in a paper entitled The Development of a Mining Operation from Diamond-Drill Data which was published in the August. 1952, issue of Mining Engineering.Geological Features of the OrebodiesThe orebodies at Snow Lake occur in volcanic rocks of acid to basic composition and, to a lesser extent, in intrusive hornblendite. The hornblendite is a massive, uniform, .coarse-textured rock except in the immediate vicinity of the ore zone, where it becomes sheared and carbonatized. The acid volcanics have been converted to quartz-garnet-biotite gneiss, and the basic volcanics to amphibolite gneiss. Orebodies have been formed by the replacement of all three rock types."

Jan 1, 1955

By V I. McCallum

In 1954, Falconbridge Nickel Mines Limited began the program of deepening the Falconbridge mine workings for 2,000 feet below the bottom, or 4025, level in order to provide twelve new levels for production. Involved in this program were a production-sized internal shaft, .crushing, pumping and hoisting installations, the integration of the new shaft operations with those of existing shafts, and considerations of ventilation requirements and ground support at depth. This paper describes the major items of equipment, and the depth development of No. 9 shaft as a whole, and also emphasize the planning phases of the program. The factors involved and reasons for the equipment and layouts chosen are given. Introduction and History THIS paper describes the planning and development of that portion of the Falconbridge mine between the 4025 and 6050 mining levels. This mine, the oldest of several being operated by Falcon-bridge Nickel Mines Limited in the Sudbury district, has been a continuous producer for over thirty years.

Jan 1, 1964

By Harold J. Rose

"A VETERAN newspaperman once summed up a lifetime of observation and experience in these words:""What man can imagine, man can do"".That statement might well serve as the theme of a talk on research potentials of the coal industry or any other industry. It is not my intention today to make a series of predictions of things to come. Experience of the past few decades has shown that long-range predictions made be-fore engineering groups usually fall short of the mark; that is, the actual technical achievements in any period tend to surpass the boldest predictions that any responsible engineer would have made, say twenty years earlier.Instead, I will point out some recent accomplishments or refer to research that is in progress or now being planned in order to suggest important trends to be expected in the next few years. Based on this rapidly increasing tempo of achievements you can make your own extrapolations into the future."

Jan 1, 1959

By L. Bos

The availability and reliability of large grinding mills and their Gearless Mill Drives (GMDs) are of paramount importance for the grinding process. Although GMDs have been in service for decades, and are known for their operational efficiency (reliability and robustness with reduced operating cost per ton), compared to conventional drives, in the last decade due to certain reasons some failures led to serious unscheduled shutdowns and significant insurance events. The majority of these notable "insured" failures have happened on GMDs installed on relatively large mills, as the financial impact of a failure is proportional to the through-put of the mill. Despite the occurrences of these events, as mining operations are driven by lower ore grades and the ability to continue reducing operating costs per ton, the trend for having larger mills is still very present and there is no reason why this trend should not continue. It is obvious that if not handled correctly, the possibility of large value GMD loss events, coupled with the continuing increase in mill size or required availability and reliability targets, could potentially lead to major conflicts as it becomes difficult for the insurance companies to judge the risk and hence may result in hesitation to insure these grinding circuits. This paper will not only describe the conflicting situation from both an insurer's perspective and from an equipment supplier's perspective, but also how these conflicting challenges can be successfully mastered. It has to be noted that not only the mining companies themselves, but also their insurance companies and the involved equipment suppliers have a common interest: to reach the highest availability and reliability in order to avoid or at least minimize unscheduled shut down times, and most importantly prevent unplanned events that result in extended production stoppages or reductions in through-put of GMD driven mills. From the very beginning onwards, the complete service concept together with emergency plans must be integrated on every level in the design of the grinding circuit. This approach must be implemented continuously and without compromises by all involved parties during all following stages, such as basic design, detail design, manufacturing, quality inspection and testing, packing, transportation, storage, installation, commissioning, operation and maintenance. The concept of formal risk analysis related to mill operations, maintenance and spare parts strategies must be an integral part of mining companies? decisions related to the selection for installation and continued use of large mills powered by GMDs. The service concept in place for operating mills shall also have a clear focus on very early detection of any abnormalities, so that the risk can be mitigated and unscheduled shutdown times avoided. However, if a major failure occurs, then procedures and tools shall already be available in order to ensure that production impact is minimized.

Jan 1, 2012

By A. Boehm

"For recycling LD slag into the steel making process, the phosphorous containing calcium silcate phases have to be removed from iron oxide phases. One possible technical solution could be magnetic separation in a wide range of susceptibilities from ferromagnetic to paramagnetic. To check the feasibility of magnetic separation the distribution of the magnetic susceptibility in size classes as well as the liberation of the phosphorous containing phase were evaluated by a new method combining two dimensional physical property analysis with QEMSCAN analysis. The particle size classes of energy controlled comminution products were subdivided into fractions of defined magnetic susceptibility using a hand magnet of well known field properties (pick up method). On the one hand the susceptibility classes were wet assayed on the other hand analyzed by QEMSCAN followed by data evaluation using iDiscover 5.3.1(FEI), which was adapted to the data structure of two physical properties (size and magnetic mass susceptibility). The results allow the comparison of mass based (3D) cumulative distribution of grades from the wet assays with the area based (2D) distribution from QEMSCAN analysis, in order to control a systematic (size dependent) stereological error for this special type of material. As the physical separation property forms a crucial parameter the results from the liberation analysis by QEMSCAN can be interpreted more profound with respect to an expectable separation result. Once the various mineral compositions of the particles are assigned to the physical properties the Henry Reinhardt chart serves to predict the best possible separation result and thus the feasibility of a separation technique.INTRODUCTIONThe two Austrian steel plants operated by voestalpine AG produce about 650,000 t (voestalpine 2014) of LD slag in the course of steel production from pig iron according to the basic oxygen process blowing oxygen in the converter by an oxygen lance. The process is also known as the Linz Donawitz (LD) steelmaking process. By the addition of lime (CaO), carbon, phosphorus, silica, manganese and sulfur, which are present in the molten pig iron, shall be oxidized and bound in the slag either as oxide or silicate phases, or leave the slag in the gaseous phase (CO). The average chemical composition of the investigated LD slag is given in table 1."

Jan 1, 2016

By John Blackshaw

NEW sources of supply of tungsten concentrates became necessary when the flow from the Far East was blocked in 1942. In Canada, one source has been noted in the workings of the Hollinger mine at Timmins, Ontario. For many years, a small amount of scheelite had been removed with the gold ore, and an appreciable tonnage of scheelite still remained in the mine. At the request of the Dominion Government, a plant was built to recover this scheelite in the form of a concentrate that could be used by the alloy-steel industry without further preparation. The plant began operating early in March, 1942, and a small tonnage of ore, carrying scheelite and gold values, has been treated daily since then. The possibility of recovering the scheelite had been considered on several previous occasions. Each time the proposal had been given up because the total profits from the enterprise were estimated to be insufficient to repay the capital cost of building the recovery plant. At the time the plant was built, additional information had been gathered about the tonnage and grade of the scheelite ore in the mine, and several thousand tons of ore grading higher than 0. 25 per cent WO3 (tungstic trioxide) were known to be available.

Jan 1, 1943

By M. O. Makwarela, M. W. Erwee, K. Bisaka

"Energy efficiency in mining and minerals processing forms part of Mintek’s long-term research strategy which includes a specific programme designed at overcoming the challenges faced by the South African pyrometallurgy industry.The electric smelting industry is currently severely constrained by the global economic downturn as well as by the availability and increasing cost of electricity. Efficient utilisation of electricity through energy recovery systems and improved smelting process flowsheets can significantly contribute towards creating sustainable operations.Apart from efficient engineering design and solid process control, smelting of either cold or hot pre-reduced ores has been shown to decrease furnace electricity consumption by more than 40%. Various methods of solid-state reduction tests have been carried out at Mintek in order to select the most appropriate process option in the context of the South African industry. This paper summarises a subset of the results obtained, specifically on pre-reduction tests done on South African chromite and manganese ore pellets.In this set of tests, it was found that the use of an organic binder, together with B2O3 as flux, promotes manganese ore pre-reduction, but retards the pre-reduction of chromite. By pre-reducing the manganese ore feed, significant cost savings can be achieved in subsequent smelting processes and there is potential to minimise manganese losses as a result of fuming, due to possible lower operating temperatures."

Jan 1, 2016

By Charles "Chick" Rodgers

"The Key Lake uranium mine is the largest single uranium producer in the world. It is owned 2/3 by Cameco Corporation and 1/3 by Uranerz Exploration and Mining. Cameco is the operator. Current production is fourteen million pounds per year of uranium oxide (U308).The mine's location is 570 kilometres north of Saskatoon on the southern edge of the Athabasca Basin approximately at latitude 57° 11 'north and longitude 105° 34' west. Access to the mine is by an all-weather road and a private airstrip.The mill was commissioned in 1983. A molybdenum plant was constructed in 1989 in response to increasing molybdenum content in the yellowcake or final product. Early test work had showed that the first ore body to be mined, the Gaertner deposit, would present few problems with regards to molybdenum in the product. However, the test work also showed that the higher molybdenum content of the Deilmann ore, the second Key Lake orebody to be mined, would result in increased molybdenum concentrations. Without the molybdenum plant, penalties would become excessive and some product might not accepted by the refineries.This paper will describe the current Key Lake mill process with emphasis on the molybdenum solvent extraction process. It will cover the chemistry of the process, process development in the mid 1980's, and current operating practices.The Key Lake milling process consists of five individual plants, crushing and grinding, leaching -counter current decantation (CCD), solvent extraction, yellowcake/crystallization and bulk neutralization (Figure 1. Simplified Mill Flowsheet). A detailed mill flowsheet can be found in the appendix."

Jan 1, 1996

"The QEMSCAN system is the third generation of automated mineral analysis systems that began with the QEM*SEM at CSIRO 30 years ago (Butcher et al. 2000). It is now a successful commercial instrument with 39 instruments in operation around the world. Back Scattered Electrons (BSE) and Energy Dispersive (EDS) X-Ray spectra are used to create digital mineral images with mineral identification occurring online. Low-count EDS spectra are used preferentially to BSE brightness, allowing minerals to be accurately identified by chemical composition. Individual minerals or groups of similar compositions are identified by comparison to a comprehensive mineral database incorporated into the QEMSCAN software. Optical mineralogy and Scanning Electron Microscopy is a metallurgists’ tool for determining the ore process mineralogy and delivering a better flowsheet. These techniques have limitations, provide limited information and sometimes fail to provide representative information. In contrast, QEMSCAN provides information on the nature and occurrence of all mineral species present plus the liberation characteristics, looking at thousands of particles in the sample presented. Some of the data presented includes:• Particle and grain sizes• Dominant mineral species• Particle shape• Calculated metal content• Density• Deportment of elements of interest between the mineral phases• Quantitative mineralogy• Mineral associations, locking and liberation• Textural relationships (particle images)It can also be used on concentrates, polished sections or drill core. This is a significant improvement in ore characterisation providing lithology, mineralogy, liberation, ore grade and porosity from a sample. Theoretical grade-recovery curves can be created to be mineralogically limited from QEMSCAN analysis which, when compared with metallurgical results, are valuable in evaluating whether liberation or chemical selectivity is driving flotation performance. A number of case study examples are given where the QEMSCAN had a significant bearing on future project development at an early stage of exploration and mine development."

Jan 1, 2012

"Syncrude Canada Ltd. operates one of the largest surface mines in the world. The mining operation has two distinct phases: (1) the removal of the overburden, utilizing trucks and shovels; and (2) the mining of oilsand with drag lines and bucketwheels. Both phases combined move approximately 330 000 BCM per day.In support of current production demands and to provide a contingent oi/sand source, Syncrude has developed an Auxiliary Production System (APS) supported by the truck and shovel operation. This system utilizes oilsand sources within the existing mine area on an as-needed basis.The recent increased capabilities of the processing plant to handle a larger volume of oilsand has increased the reliance of the APS system. To facilitate the increased capacity, an auxiliary mine was developed external to the Base Mine operation with a production capacity of4.7 MBCM of oilsand per year.Development of the Northwest Auxiliary Pit began in January 1990, with the first cubic metre of oilsand taken to the plant in June, 1990. The Auxiliary Pit, as designed, has a total ore reserve of 68 MBCM of oi/sand."

Jan 1, 1993

By John Canterford

Quay Magnesium Limited (QMG) listed on the Australian Stock Exchange in late September 2004 having raised approximately A$30 million with the object of designing, constructing, commissioning and operating a 15,000 t/a magnesium alloy production facility in Nanjing, China, Site construction commenced in February 2005 with installation of all major components completed by the end of October 2005, Hot commissioning was simultaneously commenced with the final stages of installation, leading to the first stage of continuous ingot casting by mid November 2005, Since that time ramp-up to the name plate capacity has been undertaken, This presentation highlights some of the more significant technical and logistical hurdles that have had to be overcome in order to meet the high quality product specifications required by a range of QMG customers.

Jan 1, 2006

By Ilpo O. Auranen

Background: Mines of today are moving ever increasing tonnages of rock. The new ore bodies tend be of lower grade and located deeper in the earth?s crust. The industry?s focus to overcome this ?deeper but poorer? ore problem has traditionally been to lower the costs by increasing the scale of mining. This has resulted in an ever increasing size of mining equipment like drills, loading shovels, dump trucks. The main focus has been in reducing the cost per ton of mining. This cost focus has often resulted in increased waste rock dilution and more ore losses. From costs to value: Waste rock dilution means waste rock in the concentrator feed. It?s value in open pit mining is equal to the value of ore it replaces. In underground mining, waste rock dilution?s value is equal to the value of ore it replaces added to the costs of mining it. It is commonly accepted that waste rock dilution in open pit mining ranges between 5 and 20% and in underground mining between 5 and 40 % . In a typical large open pit mine ore value is from 20 to 60 USD per ton and mining costs are 1 to 3 USD per ton. One percentage point reduction in waste rock dilution represents savings corresponding to about 20% of total mining operation costs. The difficulty of reducing waste rock dilution comes from the complicated nature of the ores. Accurate ore waste-border detection has not been possible due to excessive costs. Core drilling combined with geochemical lab analysis is the most accurate method for locating ore waste borders. However, it is also expensive and time consuming, which is why it is often combined with somewhat lower cost methods like sampling drill cuttings from blasting drill holes or from reverse circulation drills and analyzing them in a laboratory. The main drawback with these methods, in addition high costs, lies in the sampling accuracy and in the quality control of the whole process when a large number of samples have to be handled manually. In every mine it is possible to halve waste rock dilution by using new on-line analysis technology .

Oct 1, 2009

By P. P. Andrieux

The recovery of the Zone G crown pillar, located between the bottom of the open pit and the top of the underground workings at the Raglan Katinniq Mine in Nunavik, started in the summer of 2008 and should be completed by the end of 2009. This article describes the rock mechanics-based approach implemented to design the recovery of this valuable block of ore. The stereophotography-based ShapeMetriX3D technique was first used to provide a comprehensive assessment of the various joint sets that comprised the pillar. Then, the statistical distributions obtained for the dip, dip direction, spacing and persistence of these sets were used in conjunction with the geometry of the large-scale faults present in the area to build and run a series of explicit rigid numerical models. Each of these models had a slightly different jointing geometry, randomly constructed from these statistical distributions. Incorporating in a properly formulated numerical model the variability of some of the input parameters has allowed the engineering team to assess in a rational and reliable manner the likelihood of success of the proposed mining method and sequence.

May 1, 2009

By M. K. Mishra, U. M. R. Karanam

Relative to slender pillars, larger size pillars exhibit improved strata control. Fly ash, though traditionally treated as a waste product, is emerging as an alternate engineering material. This paper deals with the development of a strong fly ash composite material with additives. The geotechnical properties of this fly ash composite were determined and used to trap model core pillars, which resemble squat pillars. The trapped samples were tested under uni-axial loading in the laboratory and the results showed higher load-bearing capacity of the model core pillars. The reinforced fly ash composites provide lateral confinement and exhibit improved post- failure behaviour of the model cores.

Jan 1, 2008

By Pierre Roy, Claude Gosselin, Maryam Sadeghi, Michel Bourassa, Christian Rochefort, Claude Bazin, Gautier Mahieu, François Lavoie, Marilène Renaud, David Cataford

"Spirals are gravity concentrators used for the concentration of iron oxide minerals from ores. This paper presents the mineral size recovery curves observed for spirals operating in two Canadian iron ore processing plants. The size recovery curves are presented for rougher, cleaner and re-cleaner spirals. The partition curves observed for the spirals are significantly different than those observed for typical gravity concentration devices such as hydrocyclones or hydraulic classifiers. The size recovery curves show the complex behaviour of the minerals as they flow down a spiral and are analysed with a view toward process modelling and simulation. Initial simulation results show that gains in the iron recovery can be achieved by increasing the recovery of coarse iron oxide particles in the rougher spirals.INTRODUCTION Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and different heavy minerals ores (Wills, 1992). The classification of the particles in spirals is based on the combination of gravity, centrifuge, drag, lift and Bagnold forces (Atasoy and Spottiswood, 1995; Burt, 1984; Bouchard, 2001). Several papers are dedicated to the analysis of the forces acting on the particles flowing down a spiral (Das and al., 2007; Sivamohan and Forssberg, 1985; Holland-Batt and Holtham, 1991; Holtham , 1992). Most of these papers aim at the development of a general model for the simulation of the classification of the particles for coal ore processing. Few papers deal with the operation of spirals for processing iron ores (Hyma and Meech, 1989; Srivastava, 2001; Dallaire et al., 1978) and fewer papers present results for spirals used as cleaners following a rougher stage. Since the classification in spiral classifiers is dependent on the particle size and specific gravity a partition or performance curve commonly applied to classifiers (Mai Manga et al., 2012) is used here to analyse spiral operation. Few papers were found to describe the operation of spirals in terms of partition curves (Atasoy and Spottiswood, 1995; Holland-Batt and Holtham, 1991; Richards et al., 2000). Most of the investigations presented the application of a model to simulate the position of coal particles of various sizes and specific gravities along the trough of a spiral (Kapur et al., 1996; Holland-Batt and Holtham, 1991). In addition most of the available literature on spirals deals with one stage of concentration by spirals (Dallaire et al., 1978; Das and al., 2007; Sivamohan and Forssberg, 1985) while industrial circuits usually consist of rougher and cleaner spirals."

Jan 1, 2014