Search Documents

By Veerendra Singh, Y. Rama Murthy, Sunil Kumar Tripathy, Nikkam Suresh

"High intensity dry magnetic separation is commonly employed to separate different para-magnetic minerals including mineral sand. Separation in these separators is majorly influenced by the combined effect of gravity, centrifugal and magnetic forces on a particle. These separators are included in the process flow-sheets either for pre-concentration purposes or for the beneficiation of paramagnetic minerals. Separation in these separators is majorly influenced by the difference in the magnetic susceptibility of the associated minerals, particle size and shape along with the process variables of the machine. Particle size is one of the major parameter that plays an important role and decides its probability of selectivity under the magnetic field. However, effect of particle size on the performance of these separators are not well understood which is evident from the literature.In the present investigation, an effort is made to bring out the effect of particle size on particle separation in an induced roll magnetic separator while treating ilmenite fines. Effects of operating parameters, such as; magnetic field intensity, roll speed, feed rate and splitter position have been studied and their influence on particle size has been analysed in terms of yield (wt.%) to magnetic product, particle size distribution characteristics in terms of D50 and D80 size, skewness, kurtosis. Also, the particle size distribution of each test was fitted in Rosin-Rammler equation. The test results were analysed statistically to understand and quantify the influence of each variable on particle separation. It is found that, rotor speed of the separator had maximum influence on yield to the magnetic product whereas splitter position had major influence on D50 and D80 (µm) size of the product."

Jan 1, 2016

By H. J. Chalmers

THE H.B. MINE and concentrator are located in the Nelson Mining Division of British Columbia, on the north side of the Sheep Creek valley about seven miles southeast of the town of Salmo. It is an operation of The Consolidated Mining and Smelting Company of Canada, Limited (Cominco), which has its metallurgical plants at Trail, about 25 miles west. The property was originally staked about 1907 by Horton and Benson, whose names are commemorated in the designation "H. B." Up until 1927, a considerable amount of development work was done in the upper levels by various companies. Cominco purchased the ?property in 1927 and carried out intermittent work until 1946. Following this, an extensive surface diamond drilling programme and a subsequent underground exploration were undertaken. Sufficient ore was outlined 'to warrant the construction of a 1,000: ton concentrator. This was started in April, 1952, and completed by the spring of 1953. However, because of adverse base metal market conditions, operation was deferred until May, 1955.

Jan 1, 1957

By Judy K. Todd

Double benching has been utilized as an excavation technique in open pit mines for many years. This process involves drilling, blasting, and excavating the material for the design bench height. A second bench is then excavated without the creation of a catch bench, i.e. only minimal offset from the first bench face is allowed when drilling off the second bench. The result is a double high bench face or double bench. When drilling off the second bench, the offset of the drill from the bench face projects the lower bench face into the pit up to an extra five meters. This reduces the maximum attainable bench angle, enhances the probability of rock escaping the catch bench and increases the overall strip ratio. The generally utilized process of trim blasting also can impact on the final bench profile by contributing to blast damage of the face. BHP Billiton Diamonds Inc., Ekati Mine Diamond MineTM, has pioneered the usage of a technique that eliminates this offset. Double benching is accomplished by drilling a single, 30m pre-shear (two 15m benches) to define and protect the final bench profile. This article provides a comparison of the attained face angles obtained in the field utilizing both of the above methods, as well as a comparison with the analytically predicted angles prior to excavation.

May 1, 2002

By B. W. Smee

Glacial lake sediments or glaciolacustrine deposits form a significant portion of the Canadian, Scandinavian and Russian landscapes. Furthermore, 50 per cent of the Archean volcanic belts within the Canadian Shield area are covered wholly or in part by these deposits. Because of the high electrical conductivity and low hydraulic conductivity of these compact sediments, the application of geophysical (electrical) and geochemical techniques in such areas becomes a difficult task. The presence of these sediments has therefore hampered exploration for metallic sulphide deposits in some of the most important metallogenic environments of Canada. Similar problems exist in some tropical countries, such as Australia, where the overburden may be very conductive. In this paper, the extent and provenance of the glaciolacustrine deposits within the Canadian Shield are described. The geochemical and geophysical factors that hinder exploration in the clay belts are reviewed, with case histories of successful and unsuccessful applications of some of these techniques. The most successful geochemical technique used within glacial clay belts is the sampling of lodgement till beneath the clay cover, and the analysis of the heavy mineral fraction of that till. Surficial sampling has not been successfully applied. Some geophysical techniques, more specifically electromagnetic and magnetic induced-polarization techniques, have detected mineralization beneath substantially deep clay or saline overburden layers. Some suggestions have been made, such as the use of anions in hydrogeochemical surveys and the use of wide-band multi-frequency EM systems. When implemented, they will hopefully make the current geochemical and geophysical methods more effective in exploration for base metal sulphides within clay-covered terrains.

Jan 1, 1979

By Masami Nakamoto

Controlled thermolysis of gold(I) thiolate complex, [C14H29(CH3)3N][Au(SC12H25)2], at 180 °C for 5 h under an N2 atmosphere produces novel gold nanoparticles passivated by alkyl groups derived from the precursor complex, the TEM photograph of which shows spherical particles with average diameter 26 nm. Since Brust et al. reported the two-phase reduction of AuCl4 - by NaBH4 to afford monodispersed gold nanoparticles passivated by alkanethiolate ligands (1), plenty of preparative investigations on gold nanoparticles (2,3) and its surface modification (3,4) have appeared, because of their potential applications in microelectronics (5). However, those preparative methods generally involve the reduction of AuCl4 - by reducing agent NaBH4 in the presence of suitable organic stabilizers such as alkanethiol (1-4), phosphane (5), quarternary ammonium salts (6), surfactants (7) or polymers (8). On the other hand, O?Brien et al. recently reported the preparation of organically capped gold nanoparticles at 190 °C, where tri-n-octylphosphine oxide and/or n-octadecylamine are used both as a reaction medium and as a passivating ligand (6), but this procedure also needs NaBH4 as reducing agent. Our strategy of novel preparative method of gold nanoparticles is the combination of reductive elimination of thiolate ligands and simultaneous attachment of organic moiety on the growing nuclei. Gold(I) thiolate complexes with ammonium cations were useful for our preparative method. We now report the controlled thermolysis of gold(I) thiolate complexes, [R(CH3)3N][Au(SC12H25)2] and [R(CH3)3N][Au(SC6H4-p-R?)2] (R= C14H29, C12H25; R?= C8H17, CH3), under an N2 atmosphere, where the powder of gold(I) thiolate complexes completely melts to afford the precursor liquid and then the liquid gradually decomposes. In spite of no use of reducing agent and solvent, reduction reaction is thermochemically induced to afford novel gold nanoparticles passivated by alkyl groups rather than by alkanethiolate ligands. Figure 1a shows a typical transmission electron microscopy (TEM) image of gold nanoparticles prepared by thermolysis of [C14H29(CH3)3N][Au(SC12H25)2] at 180 °C for 5 h, indicating a controlled growth of spherical gold nanoparticles. As shown in Fig. 1b, these spherical gold nanoparticles display the size distribution ranging from 5 to 50 nm. Although the particle size is larger than that of thiol-derivatized gold nanoparticles (less than 5 nm) prepared by NaBH4 reduction (1-3), the aggregation of gold nuclei is smoothly regulated and the growth of core gold is limited to be 26 nm in average diameter in spite of thermal procedure.

Oct 1, 2003

By Ning Shi

This paper suggests an alternative design approach for an innovative shovel dipper, for use in ground conditions where cutting of virgin ground rather than scooping of blasted material is required. Not only does the new design have an optimized dimension ratio (width:height:depth) and attachment arrangement (angle, position), but also a non-linear pro¯le in 2D and 3D. The approach is based on the simulation of a shovel's duty cycle to verify a pilot dipper model. In order to achieve a realistic simulation that could be used to evaluate a dipper design, the model is e®ectively a descriptor of actual shovel activity under soft ground conditions. The shovel geometry, motion and operation, with an emphasis on digging and dumping kinematics and dynamics are the principal elements of the simulation. The simulation considers a fresh face location, repeating tucking, digging and dumping swing motions within the geometric range of the machine, ending when no more face material remaining within reach without re- positioning. The simulation yields digging force, friction force, trajectory, ¯ll time, ¯ll factor, etc, which may be integrated into two basic considerations: power draw (output) and volume delivered (production), as indicators of dipper performance. The simulation has been used as a tool to modify an existing dipper design, prior to looping further simulation cycles. Ultimately, an optimized or totally-new-concept shape is realized. A prototype dipper as a fractional scale model will be built to verity the performance under actual mining conditions.

May 1, 2004

By C. Riveros, H. Henein

Bulk Metallic Glasses have a high potential as advanced engineering materials due to their various properties including strength and corrosion resistance, to name a few. This paper investigates amorphous phase formation and rapid solidification characteristics of impulse atomized Co-based alloys in order to understand and control the application properties of the final products. Amorphous fraction and kinetic crystallization properties of the atomized Co-based alloy powders were quantified by means of Differential Scanning Calorimetry. In addition, different but complementary characterization tools were used to analyze microstructures of the powders. These include optical microscopy, X-ray diffraction and micro-hardness tests. While the amorphous fraction within the powders is promoted by high cooling rate and smaller powder size as expected, hardness is found to decrease with the fraction of amorphous phase.

Jan 1, 2015

By D. F. Kidd

Introduction In a companion article, Surveys at Great Bear Lake, 1931, R. C. McDonald has described the general character, topography, and climate of the Great Bear Lake-Coppermine River area and the main means of access (l). The present paper will largely be confined to the geological features of the district. In the last two years, the rocks of the region have received considerable attention, and papers including references to .the geological succession have been written by Knight(2), Duncan(3), Norris( 4), Reid(5), Cameron(6),and Kidd(7). The writer confined his field-work during the 1931 season to the district between LaBine point and Hunter bay and northwest to the head of McTavish arm. Brief trips were made down the Sloan river from McLaren lake, 25 miles northeast of Hunter bay, to that place, to Dowdell (Sixty-six) point, the south point of Echo bay, and to the region north of the Dismal lakes and west of the Coppermine river. The inner part of Echo bay, which is the area discussed by Reid and Cameron, has not been seen by the writer and the geology there will not be discussed.

Jan 1, 1932

By A. Mitrašinovic, A. Wolf

"The aim of this investigation was to determine the most suitable additive for recovering metals from converter slags generated during Ni extraction. Fluxes analyzed were silica and lime and reductants included pig iron, ferrosilicon and copper-silicon compound. Slag was settled at 1300°C for one hour to simulate the smelting environment. The newly formed matte and slag were characterized by chemical composition and morphology. Microstructural studies showed that slag formed after adding reductants consisted of primarily fayalite, with traces of magnetite. Entrained matte was present in the slag mostly as prills of Ni3S2-FeS matrix and a Cu2S-FeS secondary phase below 10µm in diameter. Kinetic parameters of matte formation, valuable metal recovery rates and partition coefficients were deduced. Silica additions generated higher partition coefficients for copper and nickel than the addition of lime. Additives used as reducing agents had higher valuable metal recovery rates and partition coefficients. Silica additions favoured the formation a higher grade matte while lime additions will hinder metal recovery. Pig iron, ferrosilicon and Cu30Si were the most effective reductants for valuable metals recovery. Cu10Si and coke additions had little to no effect on valuable metals recovery."

Jan 1, 2015

By C. A. Lavery

A DISCUSSION is presented of natural gas production and field processing equipment as now utilized in the gas producing areas of the United States, with reference to use of such equipment in Canadian gas areas. The scope of the paper is confined to a general description of various types and methods of using surface production equipment. The discussion is divided under two general groups: well-head production equipment, and field processing. The first will be concerned primarily with indirect heaters, separators, knockouts, and special versions of this equipment. The second major group includes the field processing equipment for handling natural gas. A delineation should be made here as to the meaning of field processing as used in this discussion. We will limit our term to mean such processing equipment as may be used in producing fields to process gas or its by products in a manner that does not require conventional plant practices either in operation or supervision. This covers such equipment as is necessary to complete preparation of gas for sale to pipeline and/ or is necessary to recover valuable components. Under this heading we will discuss glycol dehydration, solid desiccant dehydration, low-temperature separation, mechanical refrigeration, and desorbtion-stabilization. These are all processes involved in preparing gas for final sale or disposal. They do not include the more conventional and large-scale plant process systems.

Jan 1, 1956

By A. R. Sorta, D. C. Sego

ABSTRACT Temperature, solute, texture, and thixotropic effects on time domain reflectometry (TDR) measurements of water content in oil sands tailings are investigated. Results indicate that TDR water content measurements are influenced by temperature, residual bitumen, and percent clay in the tailings. A correction of 0.03–0.10/ °C must be applied to the apparent dielectric constant (Ka) to account for the effect of temperature. The Ka-volumetric water content relationships of slurries differ significantly from the commonly used Topp calibration equation. The age of the tailings and the addition of phosphogypsum did not influence TDR water content measurements.

Jan 1, 2013

By N. Parnian

"Carryover of caustic soda (NaOH) in the steam path caused catastrophic failure of superheater 304H stainless steel tubes in a steam generator and led to an unexpected shutdown after just five months of continuous service of petrochemical following the start of production. The cause of the failure was studied, with a focus on the formation of sigma phase in the weld joint and effect of caustic embrittlement on stress corrosion cracking (SCC). The cracks were examined at the seam weld, heat affected zone (HAZ), and Ubend areas. Hardness was measured for the base metal, HAZ, and weld metal, and microstructures were examined using optical microscopy and scanning electron microscopy (SEM). Crack initiation is attributed to gouging on the precipitated carbide at the HAZ and also the formation of sigma phase in the weld metal, as shown by energy dispersive X-ray (EDX) analysis. In addition, cracking was propagated by caustic embrittlement because of residual stresses and hammering. Finally, the characteristic feature of fracture was illustrated by SEM fractography, and consists mostly of intergranular SCC and some quasicleavage transgranular. INTRODUCTIONThree key factors are needed for the initiation and propagation of intergranular stress corrosion cracking (IGSCC): a susceptible material, a corrosive environment, and sufficient stress. Although austenitic stainless steels are susceptible to sensitization and IGSCC, they are widely used in boiler and superheater tubes because of their high corrosion resistance, high oxidation resistance, acceptable mechanical characteristics at elevated temperatures, and low cost.Sodium hydroxide is injected to neutralize acidic constituents in the steam path, but caustic can concentrate in boiler tubes and attack the surface metal (known as gouging) even traces of caustic in the steam can deposit on surfaces and cause local concentrations of several percent (ASM handbook, 1992). Not only sensitized grains but also sigma phase formed in the weld metal can initiate caustic cracking. In this research, the cause of the failure of 304H stainless steel superheater tubes in a methanol petrochemical plant in Iran was studied with a focus on the effects of caustic embrittlement on IGSCC."

Jan 1, 2012

By E. Adam, B. Milkereit, M. Salisbury, L. E. Reed, G. Perron

Integrating seismic reflection, borehole geophysical, and physical rock property studies is an effective means of mapping lithological contacts and structures in the crystalline crust. At Les Mines Selbaie in the northern volcanic zone of the Late Archean Abitibi Subprovince, a high-frequency seismic reflection profile has provided the first images of deep crustal structures of this important polymetallic mine site. Physical rock property and borehole geophysical studies confirm that prominent seismic reflections can be caused by lithological contacts, faults and sulphide mineralization. At Les Mines Selbaie, the first two of these are shown by this study. Clearly identifiable reflection images from sulphide mineralization have not been demonstrated in analysis of the profile. The seismic images provide useful information about gross structure in the vicinity of Les Mines Selbaie. They can also place important constraints on the sequence of tectonic events and, therefore, can aid future deep exploration programs.

Jan 1, 1997

By D. E. M. Plaumann, B. S. Fee, R. D. Hansen, R. R. Klimpel

"The steps from experimental curiosity through to commercial product can be slow and tortuous in spite of the quality of the technological advances offered by the new development. Data generation and interpretation need to be done in lab tests as well as full-scale evaluations and, in each, the advantages of the new reagent must be clearly identifiable and measurable.The Dow Chemical Company has patented a novel new collector for the flotation of zinc. Fl (2-hexylthioethylamine hydrochloride) has several unique structural features that suggest atypical mechanisms for zinc collection. Laboratory data have demonstrated significant flexibility with respect to grade and recovery balance at dosages lower than those typically used for xanthates.In mill trials, the same phenomanon is evident - the choice between high grade and high recovery allows one to select the desired quality of zinc concentrate. One trial in particular was run over a three month timeframe and Fl gave improvements in recovery of 2.5% and a reduction in lead levels with less than 0.5% loss in grade. The dosages of other reagents in the flotation circuit were also reduced.Data demonstrating improved recovery and grade in lab trials will be discussed. Extensive data from the mill trial will illustrate how Fl works in both rougher and cleaner circuits."

Jan 1, 1990

By Harry Siewert, Tom Milner, Jack Stickney

"LocationThe Gibraltar mine is located in central British Columbia (NTS 93B/9W), 362 km north of Vancouver. Access is provided by 20 km of paved road from McLeese Lake, which lies 45 km north of Williams Lake on Highway 97. Latitude and longitude of the mine are 52° 30' and 122° 16', respectively.The total area of the McLeese Lake site is approximately 1700 ha (4200 acres). This includes the orebodies, dumps, surface drainage collection system, plant site, roads and tailings ponds.Brief Description of OperationOre is mined by open pit methods and is concentrated using conventional crushing, grinding and flotation processes. Copper and molybdenum flotation occurs at an average rate of 40 000 tons per day. Tailing is discharged to an impoundment area and the water recycled as process water. Additional copper is extracted from the waste dumps using sulphuric acid as a leach solution followed by solvent extraction and electrowinning.HistoryExploration by Gibraltar began in 1964, continuing until late 1970, at which time it was announced that the property would go into production. Construction started in early 1971, with initial production in March 1972. Target capacity of 30 000 tons per day was achieved by the end of March and is currently at 40 000 tons per day.Ore reserves as of January 1, 1998 were 184 384 000 tons grading 0.31% Cu and 0.010% MoS2."

Jan 1, 2000

By A. E. Taylor, A. S. Judge, P. T. Lafleche

"Resource development in northern Canada has special requirements which derive from the unique environmental and eco-logical nature of the northern environment. In this paper several case histories in which the Permafrost Research Section of the Geological Survey of Canada (GSC) has participated are used to illustrate how geophysical methods may be used to address some of these considerations. Although some of these examples were developed while examining problems directly related to oil and gas development and transport in frontier regions, such or similar methods also have application to mining problems.IntroductionA critical parameter is the distribution and thickness of permafrost, which in northern Canada varies from being a few metres and discontinuous at the southern limit to thicknesses in excess of 700 m in the Arctic Islands'!'. Figure I is a schematic diagram of typical ground thermal conditions in a permafrost zone. The upper zone is defined by an active layer which undergoes a seasonal freeze/thaw cycle. In the simplest case, the ground remains permanently frozen below the active layer to the depth of the O°C isotherm, which is defined as the base of the permafrost. Water chemistry, pore structure and pore or grain size may cause the base of the frozen ground to be above the permafrost by up to 100 m(2). Ice can be found within the permafrost in the pores of solid rock or sediments, as massive ice within unconsolidated sediments or as ice lenses within fissures in a solid rock mass. The mining technique used in these conditions, whether open pit or underground, can differ considerably from that used in southern Canada. In the high Arctic, for instance, the dry drift method is feasible underground in the permanently frozen host rock. The frozen nature of the wall rocks can obviate water-related problems."

Jan 1, 1987

By J. H. C. Scrimgeour, T. Toong, R. E. Hamilton

"The principles involved in the use and application of mathematical models as an aid to the development of advanced process control computer systems are described briefly. This is followed by a brief survey of known models of this kind for the simulation of mining industry processes.The main part of the paper describes a dynamic model of the flotation process developed by Canadian General Electric. Using flotation rate constants for each species of mineral and gangue, the model provides a numerical solution of the differential equations describing cell behaviour. The cell mode] is used repeatedly as a subroutine in the •over-all-plant model. The features of the cell and plant models are described.Simulation runs from the plant model show stream .assays and other indications of plant behaviour printed typically in 1-to 10-minute steps for several hours of •Operation following typical disturbances such as changes in feed rate or reagent addition rate. The simulation can :Show expected behaviour for both uncontrolled and computer-controlled plants."

Jan 1, 1970

The methods employed for the addition of uranium to steels and cast iron in the Physical Metallurgy Division are outlined. It has been found that the segregation of? uranium is a major problem in aluminum and/or silicon killed steels and that the cooling rate is important in al-lowing the segregate to settle to one area, which can subsequently be discarded. The unsegregated areas were found to be extremely low in total oxygen, acid insoluble aluminum (AizOg) and, in some cases, slightly lower in nitrogen. Uranium recoveries, based on analyses of the unsegregated areas, were quite constant, at about 45 per cent, regardless of the type of uranium master alloy used for the addition. No segregation of carbon, manganese, silicon, sulphur, phosphorous, chromium or copper was observed in these steels. In commercial heats, the recoveries ranged from 7 to? 29 per cent for ladle additions to oxygen converted steel. When the steel was fully deoxidized prior to the uranium addition, recoveries ranged from 49 to 66 per cent, regardless of the steelmaking process.

Jan 1, 1964

By D. J. Bowen

"Abstract -The Great Dyke extends for 540 km along strike, to unknown depth, and varies in width from 3 km to 11 km. Rb/Sr age determinations gives values of approximately 2470 Ma.The Dyke consists of a variety of mafic and ultramafic rocks, many altered to serpentinites. These include, from top to bottom, successions of gabbro/norites, pyroxenites, peridotites/harzburgites, and dunites/picrites.The layers dip in from either margin, steepest at the edges (20°) and flattening toward the central sections. Four separate complexes are present. From north to south these are termed the Musengezi, Hartley, Selukwe and Wedza Complexes, and are described as 'boat-shaped' or 'pig-troughed'. All are similar in petrological sequences. Physiographically, the Dyke is spectacular in the north, where as a mountain range it meets the Zambezi Escarpment. Elsewhere in the central parts there is little surface expression and wide open treeless vleis. Dyke rocks cut through granite and schist belt terrain and are termed 'The Magnesia Belt'.Vast mineral resources exist. These include chrome, asbestos, platinoids, nickel, copper and gold. Up to eleven chrome seams numbered from top to bottom occur in the lower ultramafic sequences. Seams are narrow at 10 cm to 30 cm but of high grade. The platinum occurs 10 m to 40 m below the norite/pyroxenite contact.A 60 m wide zone of Light Sulfide Mineralization (LSM) of Jess than 1% sulfides extends from the lower gabbronorites into the upper pyroxenites. In this LSM, four enriched zones carry up to 5% sulfides. The most widespread is termed the Main Sulfide Zone (MSZ), below which is No. 2, No. 3 and No. 4 Sulfide Zones. The MSZ carrying pyrite, pyrrhotite and chalcopyrite is a multi­ element ore with components of PGE (Pt-Pd-Rh), nickel, copper and cobalt, and gold and silver.Extensive exploration programs have been carried out and the intention is to begin large-scale mining. However, with Russia supplying metals to the western markets, South Africa's cutback on production, and an end to the Cold War, delays have arisen."

Jan 1, 1994

By M. Girard, C. Farsangi, N. Singh

"Canadian Royalties Inc. owns and exploits the Nunavik Nickel Project: a copper and nickel deposit in Nunavik, Québec. The nickel and copper concentrates are filtered by plate and frame filter presses, and are transported 100km north to Deception Bay by truck. As the site is situated in the far north, extreme weather can be detrimental to production: roads can close for significant periods of time, resulting in the concentrator using all its storage capacity. During the winter of 2017, this accounted for over 100 hours of unplanned mill downtime. Different solutions to this problem were evaluated and the most economically viable combination of solutions was determined to be the use of concentrate storage containers and upgrading the plate size of the existing nickel filter press. By satisfying new, increased utility requirements, the cycle times would not change, but produce 30% more filter cake. Simulations were developed to determine the number of concentrate containers needed in conjunction with the upgraded press to eliminate unplanned downtime due to road closures and secure production through the winter. This paper summarises these simulations, the commissioning and start-up of the upgraded filter press, container loading procedures, and how this was put together to achieve a record 2018 winter season with a 90 percent reduction in downtime. The payback period of the project was 4 months. A specialised side-tipping trailer emptied the containers during the fall of 2018.INTRODUCTION The Nunavik Nickel Project is a nickel/copper mining project located in Nunavik, Québec. The nickel and copper concentrates are stored in stock tanks after thickening and are then filtered by plate and frame filter presses at the concentrator before being transported 100km to the shipping port at Deception Bay by trucks. The region is prone to periods of extreme weather during the winter, with winds that can reach +100km/hr and blizzards that severely limit visibility. The roads to Deception Bay are often affected by this weather, causing closures that last an average of 18hrs and as long as 72hrs. Additionally, there is a 15% chance that road closures occur within 24hrs of the last event. This has been an issue for the concentrator team since start-up in 2013, causing unplanned mill downtime every winter (Table 1) due to filling concentrate storage capacity during prolonged closures of the roads to Deception Bay."

Jan 1, 2019