Search Documents

From the mid-1970s ZC Mines at Broken Hill had a policy to increase ore production rates at progressively lower head grades. In the mid-1980s the mine suffered crippling losses at a time of low metal prices. An important contributory factor was the inherent geological distribution of metal grades in the seven defined ore lenses. Grades are bimodal, and perhaps, trimodal, in each ore lens. There is a tonnage deficiency in the critical cut-off grade zone of 7-10% Pb+Zn. Lowering the cut-off grade introduced siliceous and pyrrhotitic material which resulted in significantly poorer metallurgical performance. This example shows that the mine geologist needs to know the grade distribution of the orebody and to convey clearly the downstream implications of changes in the head grade.

Jan 1, 1990

By Hughson B

A multi-wire borehole instrumentation system was used to monitor strata movement caused by a retreating longwall face at the Ellalong Colliery, situated in the Lower Hunter Valley in New South Wales, Mechanical anchors were placed at various horizons in the borehole which extended from the surface to the extracted coal seam. The vertical movement of the anchors was monitored during mining. The zone of major disturbance was confined to 13 times the extracted seam thickness above the seam. The average dilation of strata in this zone was 6 per cent. Above the caving zone, the tensile strain was under 2mn/m except at one location, where it was `xmi/m. The subsidence trough under dynamic conditions was flatter than that under stationary conditions. The subsidence also depended upon the extent of strata fragmentation prior to undermining.

Jan 1, 1987

Existing fluid flow techniques may be readily applied to the design of ranges for seam gas drainage. The Reynolds number characterises the flow regime within the pipe and it can be used in conjunction with data on absolute pipe surface roughness to determine the system friction factor. The application of the solution to the isothermal compressible flow equation utili- sing Moody friction factors and the concept of equivalent length of pipe for fittings and valves provides a practical method for sizing gas ranges. The physical capacity of a range can be decreased by the existence of significant quantities of water in the range and also by the ingress of air into the system at poor pipe joints etc. Both problems can be elimin- ated by adequate attention to design detail.

Jan 1, 1982

By Morrison RD, Peberdy NJ

Simulator training provides a cost effective method of training operators in both the process and control aspects of a metallurgical plant. The components and requirements of a training simulator are described along with the benefits to be gained from simulator training. A table summarizing some applications of metallurgical training simulators is Given.

Jan 1, 1991

The coastline is. an incomparable stretch of sea coast known as Ninety Mile Beach. Two gas pipelines and two oil pipelines carrying hydrocarbons from thb'Bass Strait fields to the markets of Australia cross this beach. They cannot be seen as they are laid in trenching stretch- ing many miles out to sea and the beach was restored to its natural state. Even where the dunes were disturbed, suitable grass was sown thus consolidating the sand and preventing erosion. Ninety Mile Beach is but one of the many key.wildlife and recreational areas that our operations must be concerned with. Others include Westernport and Corner Inlet, but the one discussed in this paper in particular is the platform area of the Bass Strait itself. Never was the old adage "an ounce of prevention is worth a pound of cure" more meaningful than in offshore oil production. All are well aware of some of the events of the past several years that resulted in large and costly oil spills. Far less is known, seen or publicised about the measures and developments that are undertaken to ensure that such events do not occur. We also have well developed plans for response in the event of an emergency situation, which can be initiated with great rapidity. Our responsibility is to ensure that with the best of engineering technology and operating procedures, spills do not occur.

Jan 1, 1971

Perhaps no aspect of the investigation of an ore-deposit is of greater importance to the mining geologist and engineer than a consideration of its geological structure. A thorough understanding of the type, size, shape, and arrangement of any ore-body is essential to the proper conduct of exploratory, developmental, and mining, operations. Significant as these remarks are' in relationship to ore-deposits in general, they become of paramount moment when a complex structure such as the Broken Hill Lode is in question. In this connection the use of the term "lode" as applied to the Broken Hill ore-bodies may terid to confusion of ideas among those not familiar with the field or with the literature pertaining thereto, by reason of the fact that it is generally understood that a "lode" is characterised by simple, tabular form, regular outline, defined walls, and persistent attitude. However, as the terminology is well established by common usage, itsretention appears desirable, and, for the purpose of this paper, the name "The Broken Hill Lode" refers to that complex unit which includes pre-eminently the famous ore-bodies exposed in the workings from the North Mine on the one extreme to the South Blocks (Zinc Corporation) Mine on the other.That the practical value of geological investigation, of the ore-bodies was realised by the Geological Sub-Committee of the late Scientific Society of Broken Hill is attested by the...

Jan 1, 1932

By Stevens LG, Mok JK

With the long lead time requirement for engineering and construction of mineral pro- cessing facilities and the costly financing arrangements necessary, effective project management is essential to the successful and timely start up of these major production units. An added complexity is the frequently remote location of such projects and the demands this imposes on efficient project staffing, scheduling, logistics and cost control. Parsons recent experience with major projects such as Greenvale in Queensland and La Caridad in the desert of Northern Mexico and at remote locations like Sar Cheshmeh in Iran are described. The applications being developed for improving project controls through the use of computer techniques such as MSCS-COPES, and readily accessible and versatile transportation means are reviewed.

Jan 1, 1981

The collapse of the I.T.C., the subsequent fall in the price of Tin, and the lifting of quotas saw the Renison concentrator resuming full seven- day operations at maximum capacity in 1985/86. Performance was sus- tained in terms of grade and recovery, and in some areas improved, over this period. A further challenge was declining head grades, and the need to treat higher proportions of less amenable ore types. The complexity of the flowsheet and the method of mining and ore handling predisposes the process to unstable operation, and solving this problem comprises a major component of the current development effort. The concentrator has an imbalance of capacity between processes, and excess in some areas is being adapted to enhance the capacity of others. Magnetic susceptibility of various minerals is being exploited to greater effect. Significant performance gains are achievable by improving exist- ing unit process efficiency, particularly in grinding, gravity processes and Cassiterite Flotation. This paper reviews the metallurgical developments, both recently implemented and planned for this year, which have contributed to main- taining Renison Limited in a competitive position in the post I.T.C. Tin industry.

Jan 1, 1988

Perhaps the only thing certain about an address that purports to look into the future of any human endeavour is that time will prove it :.o be inaccurate. In undertaking the dubious, but oft-times necessary business of prediction, thr, historian will base his/her forecasts on tr-ands of the past, the speculator on current events, and the politician on what he/she would dearly like to see happen. The thoughts expressed in this address seem to have arisen through exercising a combination of all three of those philosophies but, hopefully, with a smat- tering of pragmatism.

Jan 1, 1988

By Whittle J

Definition of the optimum open pit, whether an intermediate phase or final design, will be sensitive to many factors. The most basic will include geological and mining constraints, mining and processing costs, pit slopes and product prices. The application of the three dimensional Lerchs-Grossmann pit optimization procedure to this task is described for a range of gold deposits. A new approach to the modelling and manipulation of the geological model enables complex geological environments to be assessed, and sensitivity analyses to be developed. Comparisons with manually developed pit designs have been made to validate the results. The computer implementation is simple to use and can be adapted by non-computer professionals at mine Sites.

Jan 1, 1986

The geologic settings, geochemistry of host rocks, mineralogy and metal values in modern back-arc volcanic-hosted massive sulphide (VHMS) mineralisation are very similar to those in many ancient polymetallic VHMS deposits. The geology, distribution and styles of seafloor mineralisation in modem back-arc basins, especially the eastern Manus and Lau Basins, southwest Pacific, are compared to VHMS deposits in the Mount Read and Mount Windsor districts of Australia . Based on exploration and research in modem back-arc settings, geologists are now observing the direct analogues of the polymetallic VHMS deposits currently being exploited in ancient back-arc volcanic belts throughout Australia and the world.

Jan 1, 1995

In recent years a large amount of work has been done at various plants overseas, and also at Broken Hill Associated Smelters, Port Pirie, South Australia, on the use of Dwight Lloyd sintering plant gases for sulphuric acid manufacture by the contact process.Several plants have modified their sintering machines and operating procedure, and some have adopted gas recirculation techniques, to obtain a relatively high proportion of the sintering plant gas at an S02 concentration acceptable to a contact acid plant 1.These adaptations were investigated at Port Pirie, and it was found that gases of suitable S02 concentration could be obtained. The results justified installation of a contact acid plant and a decision was accordingly made in 1949 to construct such a plant.However, the local conditions presented some difficulties not generally encountered at other plants, the chief differences being:a. For maintenance of production of 98% H2S04 , an unusually high S02 concentration is required, because of the prevailing high temperature 'of the purification train cooling water.b. The entire sintering operation is conducted on two large machines, 55ft. x 10ft., operating in series as "First" and "Second over" machines (a two-pass roast.) Any interruption" to either machine causes a complete interruption of plant operation and gas flow.

Jan 1, 1951

By B Hooper

Deep cuts in CO2 emissions will be required to stabilise and, in the long term, decrease CO2 concentrations in the atmosphere. Technologies for capturing CO2 from major stationary sources (power stations, industrial plants, etc) and storing that CO2 for long periods of time is one of few near term options for decreasing CO2 emissions. This transition to low carbon intensity energy and possibly the hydrogen economy through renewables and in the long-term technological developments such as artificial photosynthesis.Capture of CO2 from post combustion emissions can be done using a range of technologies though costs are currently high and dependent on the concentration of CO2 in the emissions. Techniques include solvents, pressure swing adsorption and the use of membranes. Options for decreasing capture costs by increasing the concentration of CO2 in the emission stream include the use of oxyfuels (in pulverized fuel types boilers) and by moving to integrated gasification combined cycle (IGCC) operations either simply for power generation or for poly-generation opportunities. Once the CO2 has been captured it can be stored using a variety of methods. Storage in the ocean has been suggested but is considered an unlikely option because of environmental uncertainties and political opposition. Mineral storage is a niche opportunity. The greatest potential lies in geological storage of CO2 and this option is commanding increased attention from the Australian and international community.In Australia, the Cooperative Research Centre for Greenhouse Gas Technologies (CO2CRC) is an important new initiative that will support energy companies and energy intensive industries in meeting challenges posed by greenhouse gas issues and assist them in their efforts to reduce their emissions profile.The progress of geo-sequestration and the challenges in the capture and separation of CO2 in the process industries are discussed.

Jan 1, 2004

The Hellyer deposit, hosted in the Cambrian Mt Read Volcanics, displays features typical of volcanogenic massive sulphide orebodies. These include a well developed stringer zone, metal zonation within the orebody, a polymict volcaniclastic sequence flanking the deposit and a hangingwall alteration plume in overlying basaltic pillow laves.Mapping and core logging is very detailed in order to extract as much data as possible from the deposit and its host rocks. A geological log suitable for direct computer input was adopted shortly after the deposit's discovery.

Jan 1, 1990

By R Williams, P Godwin

In a time of changing rainfall patterns and in the light of recent tailings dam failures, there is closer environmental scrutiny for proposed tailings dam construction or expansion. Therefore the elimination of the traditional tailings dam could provide both environmental and cost benefits to an operation. One method to dewater tails is using pressure filtration to achieve lower moistures than what is currently available using other dewatering technologies. Further benefits include a higher rate of filtrate recovery, reuse of waste material and the potential for dry stacking of the filtered tailings cake, thereby minimising both risk and cost. This paper chronicles the replacement of two existing belt filter presses with a single McLanahan recessed plate filter press to dewater a tailings stream at a Bacchus Marsh site. It covers the slurry testing, equipment selection, installation, commissioning and operation of the filter press to achieve the following objectives:• removing the current tailings dam and slimes cells from the existing process to minimise failure risk and reduce the cost of a dam upgrade, as well as operational and maintenance costs• free up the surface area which was previously occupied by tailings dams and slimes cells• recover additional water to be returned to the process• reduce flocculent usage• reduce truck movements and handling.The project’s owner also expects to reduce carbon emissions by over 3000 t over the lifetime of operation as well as substantially reducing operating expenditure. By recognising the carbon reduction benefits, the project owner was able to successfully achieve partial funding through the Voluntary Waste Industry Protocol.An unanticipated, but as yet unquantifiable, bonus for the project was to seek an offtake agreement for the tailings thereby allowing the tailings to be considered a valuable source of beneficiated clay suitable for the construction industry.CITATION:Godwin, P and Williams, R, 2017. Pressure filtered tailings – environmental and cost benefits, in Proceedings MetPlant 2017, pp 324–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

The process of refurbishment is not a precisely defined one. It is under- stood to mean an upgrading of a plant which is normally performed only once. The application of refurbishment in the field of materials hand- ling equipment poses particular problems because complex plants con- sist of individual components having quite different remaining service lives. For this reason, a systematic, proven procedure is proposed for the refurbishment of large materials handling equipment, designed to ensure economic implementation in accordance with the company goals. Rheinbraun2 has been using materials handling equipment since 1900, the largest units today being bucket-wheel excavators with a daily capacity of 240,000 bank cubic metres of overburden and a service weight of up to 13,500 t (metric tons). Since 1975, more than 50 large-scale refurbish- ment projects have been carried out in the company. In the process, refur- bishment has turned out to be the proven alternative to replacement of large materials handling equipment. Rheinbraun Engineering,3 a Rhein- braun subsidiary, carries out planning, consulting, and supervising work in the implementation of refurbishment projects in Germany and abroad. The most recent example is the refurbishment of Dredger 11 of the State Electricity Commission of Victoria in cooperation with Krupp-Australia, Melbourne.

Jan 1, 1989

Drill and blast excavation in underground mining and. civil engineering projects has grad- ually given ground to mechanical boring of tun- nels, shafts and raises during the past twenty years. The use of.boring equipment must today be considered significant and wide spread al- though comprising only a very small percent of total underground excavation. The encroachment of mechanical boring into the domain of blast- ing has been by slow incremental advances. There have been few, if any major breakthroughs in this development, and none can be foreseen in the next decade. After 1990 it is possible that scientific. development will provide some form of breakthrough in rock breaking, but this is so uncertain that it should have little relevance to planners in the 1980's. A more near term view of the future, con- centrating on the next five to ten years, has lead to the conclusion that significant im- provements will be seen in tunnel borers for poor ground conditions. A universal machine will be developed that converts from a dry hard rock machine to a closed slurry type machine for passing through fault zones with unstable crushed rock and water. Two other machines have been described as alternate designs for tunnelling in squeez- ing ground conditions.

Jan 1, 1981

The world is getting flatter through internet, mobile phone technology, relatively low cost travel, massive outsourcing of manufacturing to China and the transfer of company backroom operations to India. In the iron and steel industry, however, things will remain relatively the same with slow gradual improvements in technology; only the geographic location of plants may change over time. Or will it? The blast furnace smelting process has remained largely unchanged since 1828 when James Neilson came up with the idea of preheated air being delivered to the tuyeres. Likewise, oxygen steelmaking that takes molten iron from such blast furnaces has remained conceptually unchanged since Sir Henry Bessemer invented an air-based system in 1856. These two processes are the core of integrated steel mills that we know today. Typically such mills consist of coke ovens, sinter plant, blast furnace, oxygen steelmaking, continuous caster, rolling mills and metal coating lines. In the intervening 150 years the only real disruptive technology to the integrated steel mill has been the minimill. Based on the use of the electric arc furnace (EAF), in conjunction with a continuous caster and rolling mill, the term minimill is used because steel products are produced at down to one-tenth the scale required for economic operation of an integrated mill, with the EAF producing molten steel using largely scrap steel as its feed, as against transforming coal to coke (coke ovens), iron ore, coke and limestone into molten iron (blast furnace) and molten iron to steel (oxygen steelmaking). There are, however, a number of technologies in development that may cause a paradigm shift in the way steel products are produced and perhaps push the evolution of the minimill as a disruptive technology. Two examples are direct iron smelting, where iron is produced in a matter of seconds by injection of ironmaking feed materials into a molten bath, and thin strip casting, where molten steel is cast into 2 mm strip or less, in similar time. Both have Australian connections. A leading iron smelting technology is the HIsmelt« process, which has its first commercial application at Kwinana, Western Australia, where a joint venture of international parties, consisting of Rio Tinto and the Nucor, Mitsubishi and Shougang corporations, are in the stage of ramping up commercial production. The leading strip casting technology is the Castrip« process that arose from development work done by then BHP Steel, with IHI of Japan, at Port Kembla, New South Wales in the 1990s. Nucor followed this work up, building the first commercial plant for the technology at its Crawfordsville site in Indiana in 2001 and has recently announced an intention to build a second plant in the USA. While both technologies are only into the early stages of commercialisation they are likely to change the face of iron and steelmaking as we know it over the next 20 years. This paper elaborates on the technology of the two processes, why they could change the face of the iron and steel industry forever, what might drive the rapid change and what the changes may look like.

Jan 1, 2006

By D Henderson, K Howie

In 2005, Glass Earth Limited (GEL) commissioned two large area detailed airborne geophysical programmes in the Taupo Volcanic Zone (TVZ). In the first survey Bell Geospace Ltd of Scotland conducted an Air-FTG« (airborne Full Tensor Gravity Gradiometry) survey covering 2338km2 at 300m line spacing. The second survey by UTS Geophysics, Australia included detailed airborne magnetic, radiometric and digital terrain data capture covering 5341km2 at 150m line spacing.   From the detailed geophysical data collected it is possible to identify major deeply penetrative crustal structures within the TVZ, as well as define subsurface geological features, such as intrusive bodies and alteration zones. These major deep crustal structures are thought to have a controlling influence on the distribution of epithermal gold mineralising systems, and along the corridors defined by these deep crustal zones, the chances of discovery of an economic epithermal gold discovery are greatly increased.   In this paper GEL gives some examples of the application of its integrated data driven approach to exploration in the TVZ at both regional and project scale. The paper focuses on how GEL identifies regional scale highly prospective deep crustal structures. Then, using the Horohoro epithermal gold system as an example, we show how GEL applies innovative geological and geophysical data processing to model and understand detailed subsurface geology, focusing subsequent exploration to ensure the best opportunity for a new economic epithermal gold discovery.

Jan 1, 2007

By Adshead ND, Blake KL, Rotherham JF, Rotherham M, De Jong G

Magnetite deposits with distinctive ¦ actinolite ¦ apatite -bearing gangue and spatially-extensive sodic-calcic wall rock alteration occur in both Proterozoic metamorphic terrains and Mesozoic-Tertiary magmatic arcs. Examples from both settings constitute significant sources of iron ore (e.g. Kiruna, Sweden; El Romeral, Chile) and some host major Cu-Au deposits that have a local association with K-silicate alteration (e.g. Cloncurry district, NW Queensland; Copiapo district, Chile). A growing body of evidence points to a hydrothermal origin for these systems involving high temperature, low S oxidized fluids. The Cloncurry magnetite-Cu-Au deposits are products of the local structurally channelized influx of a specialized high salinity ore fluid into larger-scale alteration systems developed during pluton emplacement at greater depths than those associated with subvolcanic (porphyry) Cu-Au deposits. The geological characteristics of deposits in magmatic arcs are consistent with a similar mode of origin albeit in rather different tectonic settings.

Jan 1, 1995