Search Documents

About 74% of global seismic energy release occurs in the Circum-Pacific zone. Worldwide, about 71% of seismic energy release is in the form of shallow earthquakes, 27% as intermediate, and 2% as deep earthquakes. Seismic energy release is variable in time and has been shown to correlate with the amplitude of the Chandler wobble. It was high during the period 1949 to 1967, and is now at a rather low level, with the latest earthquake over M = 8.0 having taken place in Indonesia in 1971. The average worldwide recurrence rate for the expected largest magnitude earthquake (M "9.5) has been estimated as several tens of years, in marked contrast to the several tens of thousands to hundreds of thousands of years separating the largest volcanic eruptions. Geological studies are needed to establish reliable mean intervals between large earthquakes, and to detect the e;:istence of long-term fluctuations in the ste of occurrence. Seismic gaps have proved seful in static forecasting of large earthquakes, by identifying places where closer study of the variation with time of seismicity, deformation, and other parameters, may lead to the dynamic p_ediction of time, place and magnitude of earthquakes. The model of stress concentration at asperities explains the main features of seismicity in the Circum-Pacific. Slow earthquakes have been detected instrumentally, notably an event immediately preceding the 22 May 1960 Chile earthquake, the largest this century. It seems likely that this type of deformation may explain both instrumentally detected and macroscopically observed pre-seismic deformation, as well as unusual animal behaviour reported before some earthquakes. Seismic and volcanic events are interdependent, with large earthquakes commonly triggering eruptions. Melting of rock and intrusion of magma is likely to accompany many earthquakes.

Jan 1, 1987

By Lownds C. M

Several classes of commercial explosives and blasting agents behave non-ideally, especially in diameters near their critical diameter. A direct and convenient measure of non-ideal behavior is the detonation velocity (VOD); if the VOD is less than the ideal value, usually obtained by calculation, then the explosive is detonating in the non-ideal mode. Such lowering of the VOD is usually due to both lateral loss of energy and post-CJ release of energy. The second of these factors, namely slow release of chemical energy, is of most interest in blasting. While the observation of a low VOD clearly suggests slow reaction of part of the explosive composition, it does not necessarily mean that the energy is lost to the overall rock-breaking process. The partition of the energy of the explosive into various useful and wasteful categories is considered. Simple models of energy partition in blasting, and of explosive reaction kinetics, are presented. The models consider the effect of explosive type and rock type, the explosive being described in terms of the most common phases namely liquid, air bubbles, porous ammonium nitrate, dense or crystalline ammonium nitrate, and aluminum. Over a range of combinations of the above phases, the model predicts reasonable critical diameters and VOD's. Results are presented which show the effects of non-ideal detonation on fragmentation and heave in different rock types. Conclusions are drawn about those blasting conditions in which ideal behavior is beneficial, or Disadvantageous.

Jan 1, 1990

The Transportable Moisture Limits, as ,measured by the procedures laid down in The IMCO Code of Safe Practices for Bulk Cargoes, determine the target moisture contents for the concentrates produced at the West Coast Mines of Electrolytic Zinc Company of Australasia Limited at Rosebery. Filtration of these concentrates gives moisture contents considered to be low in comparison with those achieved for similar sulphide concentrates, but which are very close to these Transportable Moisture Limits. The filtering techniques used are outlined and the problems associated with-maintaining concentrate moistures below the required limits, together with the methods used to solve these problems are discussed.

Jan 1, 1978

The published safety policy of Mount Isa Mines Limited, together with details of the organisation and control techniques adopted by management to pursue an active safety programme within the company, is presented. The importance of communication by management through the organisational hierarchy and procedures instituted to ensure rapid and concise feedback on safety concerns are detailed. The paper also describes the role of the occupational health department and safety committees in assisting management to monitor the safety effort of supervisors and employees. Current safety performance levels are tabled together with details of some aspects of the programme on which safety effort will be concentrated in the future.

Jan 1, 1975

By M Surtees

The Limpopo region in southern Africa is considered to be a favourable target for the discovery of base and precious metal mineral deposits. The integration of gravity, geomagnetic, LANDSAT data and geotectonic history is used to formulate an ore deposit model which can be used in the implementation of mineral exploration programmes. Field work was carried out to test and refine the model.

Jan 1, 1993

By P C. Hagan

Production scheduling is often reliant on an estimation of a mineÆs trucking capacity. While this mechanistic approach is relatively simple, it often over-estimates actual throughput resulting in under-utilisation of downstream process and a shortfall in revenue. An alternate approach has been developed that recognises the interdependency between processes in the mine production system including materials loading, haulage and crushing. This approach incorporates a heuristic model based on queuing theory that accounts for the variability in performance of individual processes and that this paper presents the results of a study comparing the conventional approach to mine scheduling with a capacity constrained model at a large open cut mine having a truck and shovel fleet. The capacity constrained model consistently predicted a lower material throughput compared to the conventional approach. Differences in throughput between the two approaches were found to increase with loading time, for example when loading time exceeded 3.9 minutes there was a shortfall of up to 40 per cent in estimated throughput. Longer travel times tended to ameliorate any differences. When applied to a mine schedule that extended over a two and a half year period, the difference was equivalent to a shortfall of nearly eight per cent in total material movement.

Jan 1, 2007

The first stage in the refining of lead blast furnace bullion is the removal of copper and this is normally done as a batch process in open kettles,A number of attempts have been made in the past to establish fontinuous processes operating in reverberatory type furnaces, but the growth of accretions in the furnace has always presented a serious problem.This has been overcome in the plant of the Broken Hill Associated Smelters Pty Ltd at Port Pirie by the construction of a reverberatory furnace and ancillary cooling system of novel design.Although a number of mechanical and metallurgical problems still remain to be solved, it is claimed that a workable continuous copper drossing process has been established.

Jan 1, 1963

By Johnson D. P, Beamish B. B

The northern Bowen Basin has a very large resource of coalseam methane gas-in-place - 136 TCF(7ohnson and White, 1988). The gas is pipeline quality, being 98-99 per cent methane with traces of carbon dioxide and higher hydrocarbons. The largest resource of natural gas within the coalseams of the northern Bowen Basin is contained in the Moranbah Coal Measures (75 per cent). The next most important resource is in the combined upper Fort Cooper (16 per cent) and Rangal (nine per cent) Coal Measures. The far northern parts of the basin have low gas contents due to the combined effects of limited extent of the coal measures, shallow depth and low rank. Reserves per well are more than double that of the best coalseam methane wells in any basin in the United States. In some areas of the Moranbah Coal Measures, the gas-in-place estimates exceed 225 million cubic metres per well (80-acre spacing). A distinction is made between resource base, as determined from this basin assessment, and the deliverability potential. Parameters used to estimate gas-in-place (coal area, thickness, density, rank and depth) can be adequately extrapolated from areas of high- to low- data density. Parameters affecting methane production (permeability, gas depletion factor and critical desorption pressure) cannot be generalised. Exploration and development programs must rapidly develop a predictive capability for these factors, on a local scale, through geological modelling and confirmation drilling.

Jan 1, 1991

In mid-1998 Atlas Copco Rock Drills AB introduced the first member of a new family of drill rigs. This new family, Rocket Boomer L1C/L2C/L3C, is based on modern computer technology and also on what is characterised as information technology. The design of the drill rigs are modularised both in hardware as in the software. This means that the functionality of the drill rigs is upgradable step by step. Added upon the basic drill rig functions are the new options as ABC Regular (known also as Contour Control), ABC Total, drillplan generator and communication products. The main objectives of these functions are to facilitate real quality drilling.

Jan 1, 2003

By G Ride

The provision of a water supply is a major consideration in planning mining developments particularly in remote areas. The evaluation and development of adequate water supplies in arid areas of Australia is often as important as the discovery of the orebody. The copper orebody at Warrego near Tennant Creek could not be mined economically if cheap treatment water was not available near the mine. This paper describes the difficulties in obtaining water in the Tennant Creek area and the water supply investigations carried out near the Warrego Mine which resulted in the successful discovery and evaluation of a reliable large scale water supply. It is contended that the establishment of a water supply must be approached on a systematic and scientific basis similar to the approach with the exploration and establishment of actual ore reserves. Mining companies with similar water supply problems may benefit by approaching their problem on this basis. The approach adopted by Peko Mines is outlined in this report.

Jan 1, 1971

Reconciliation of the ore reserve has been an integral part of mine planning since Bougainville Copper Ltd. commenced mining operations at Panguna in 1972. Confidence in the ore reserve is considered essential, both for long term planning of the deposit, and for fair and accurate reporting of the mining resource to shareholders. Recoverable, proven reserves are published annually. Although the ore reserve quoted is based only on diamond drill hole (DDH) information on a 122 metre by 122 metre grid, predictions are regularly reviewed against production. Concentrator results are taken to be the best estimate of grade and tonnage. Surveyed mined perimeters and average blasthole grades are reconciled at the end of each month against the concentrator figures. Predictions of the in-pit reserve are made using an orebody model. DDH and blasthole (BH) sample grades are used to make predictions for both long and short term planning. This paper describes how reconciliations are used to validate ore reserves at Panguna. Development of the orebody model is described, and some of the difficulties encountered in doing reconciliations are addressed.

Jan 1, 1987

The proximity of the Town of Kalgoorlie to the Mount Charlotte mine necessitates that charge weight per delay be limited in order to keep surface vibration levels within acceptable limits and to reduce damage to underground workings. The mining system requires that large mass blasts must be used to recover pillars and therefore a large number of separate delays are needed. Until recently all blasting has been done electrically, fired from mains, but with the introduction of large diameter blastholes (165mm diameter) this firing system was inadequate. Various firing systems were considered, but after extensive trials a non-electric sequential firing system was chosen. This system fulfilled all criteria of blast design, was relatively straight forward in charging technique and had a very simple primary initiation system. Although initially designed for large mass blasts, the non-electric firing system is now used for all large hole blasting and in a simpler form for small (57mn diameter) holes.

Jan 1, 1982

By McCarthy PL

Widespread interest in reopening Victorian gold mines, regenerated by increased gold prices, has highlighted the technical problems prevailing. A combination of historical lease legislation, minimal recent mining activity, forms of mineralisation, high insurance rates and tortuous approval requirements for mining mean the potential investor assessing an old mine must address a wide range of technical problems. The requirements for establishment of ore reserves and attraction of capital for mine development are fundamental. Underground reef mining was historically generally on a small scale, and as mining on many fields ceased about the turn of the century, past geological and production records cannot be correlated to personal experience and comment. The impact of modern mining technology on future reef mining will be to reduce operating costs and significantly improve historic metallurgical recovery. Roth these are commensurate with increased capital costs. Workers compensation rates currently applicable in Victoria are many times higher than in other states, adding significantly to operating costs. Establishment of a pilot plant testing facility in central Victoria would provide an invaluable service in treating bulk samples essential for grade and recovery assessments of Victorian ores.

Jan 1, 1982

By Hughson B

At present sane man-made Improvements and natural features are constraints on unlimited underground mining. 7 hey will continue to remain, as constraints on the future high production mining systems as wall. Unless these constraints are overacTe by research, where possible, future high production systems may became unacceptable. 7 he areas of future research include improved subsidence prediction techniques applicable to future mining systems, subsurface subsidence behaviour, mining systems capable of producing no surface subsidence and subsidence damage assessment.

Jan 1, 1988

By McMullen P. H

Mining of copper ore at Mount Lyell has been continuous since 1893. The operation has always been marginal and the depressed copper Market over the last decade has seen mining continue on the basis of a series of short term plans. In 1985 it was determined that the mine would close in 1989 on completion of the 40 Series mining block. Significant changes in the value of the Australian dollar in 1986 and the subsequent effect on profitability dictated a review of the Company's operations. Lower level ore reserves, mining methods and ore handling systems were re-examined and a plan proposed for mining of the 50 and 60 Series mining blocks. The improved economics of this plan, together with workforce and State Government initiatives resulted in an extension of mine life to 1994.

Jan 1, 1988

The Jurassic Walloon Coal Measures crop out over much of the Moreton Basin and contain numerous thin, banded coal seams which have been mined at various locations since the 1870s. Historically most mining has been by underground methods. Increased exploration during the 1970s and 1980s has led to the delineation of significant open cut coal resources and to the development of the Oakleigh, Jeebropillly and Ebenezer open cut coal mines in the Rosewood-Walloon area. Over 2 170 million tonnes in-situ of shallow, high volatile bituminous coal with a mean maximum vitrinite reflectance of between 0.5 and 0.6 have been proven in the Basin.

Jan 1, 1991

The Youga gold mine in Burkina Faso, West Africa, is scheduled to produce first gold in the third quarter of calendar 2007. The project is expected to produce 540 000 oz of gold over 6.5 years, from a conventional open pit carbon in leach mine. The direct capital cost of the project is US$47 M. Etruscan Resources Inc, a Canadian based gold exploration and development company, holds 90 per cent of the project company Burkina Mining Company SA (BMC). The state of Burkina Faso is free-carried for the remaining ten per cent of BMC. RMB Resources Limited, of Melbourne Australia, has arranged a US$35 M project finance facility for BMC (the Borrower) as the majority of funding for the Youga project development. The loan facility was provided by RMB Australia Holdings and Macquarie Bank Ltd (the Lenders) each as to 50 per cent in the lending syndicate. The Lenders also provided a gold hedging facility to guarantee a minimum price for the projectÆs gold production. Burkina Faso is a francophone country, part of the Economic and Monetary Union of West Africa (UEMOA). The project financing is the first such facility to be arranged for a mining project in Burkina Faso, with little or no precedent available in other UEMOA countries. Therefore, while the Youga gold project is forecast to be a robust project applying conventional mining and processing methods, a number of legal, technical, commercial and social issues required identification, evaluation and resolution before the loan could be established. This paper describes that evaluation process and the resolution of these issues. In-house experience and expertise in both the LendersÆ and BorrowerÆs teams has facilitated a greater understanding and æownershipÆ of the issues and hence provided comfort with risks which might not normally be taken in conventional project developments and project financings. As a result, blanket external reviews were not required by the Lenders. A long-standing relationship between Etruscan and RMB Resources also facilitated solutions to a number of issues. Nevertheless, a degree of flexibility by the Lenders, the Borrower and Etruscan was required to successfully close the financing.

Jan 1, 2007

By J M. Palin

Hydrothermal scheelite precipitated in fault-veins at Paradise, Bonnie Jean, Davidson's and Glenorchy mines display chemical variability involving REE patterns that are transitional between two end-member types. Type I is a MREE-enriched pattern with no or a small positive Eu anomaly. Type II is a flat to MREE-depleted pattern with a strong positive Eu anomaly. The chemical inhomogeneity of these scheelites can be explained by a model of fractional precipitation of REE, with preferential removal of MREE from the fluid during precipitation of scheelite. Irrespective of the mechanism responsible for scheelite precipitation, the source of dissolved constituents is different for scheelites from the Paradise Mine. Bonnie Jean, Davidson's and Glenorchy scheelites formed from LREE-enriched fluids whereas Paradise scheelites precipitated from fluids that were lower in LREE. These inferred fluid characteristics cannot be linked unambiguously to specific source rocks in the region, but could suggest that scheelite deposited in the Paradise fault-vein reflects a more mafic source of REE possibly greenschists, whereas the REE in scheelite from the other mines suggest a more felsic source.

Jan 1, 2003

By S Wasi, J Tobiczyk, J Roszkowski

Methane and fire hazards have a vital effect on work safety and continuity of mining plant operation. In the 1990s, the SMP hazards monitoring and ventilation control systems, based on continuous measurement of air parameters, were put into operation at nearly 30 Polish mines. These systems provide continuous measurement of methane concentration within the range of zero to 100 per cent with automatic switching off of electrical energy immediately after detection of potentially explosive conditions. Early detection of coal spontaneous combustion and open fires is made by continuous measurements of CO, CO2, smoke and O2 content in mine air as well as temperature changes in air and rock mass. The essence of the system is intrinsic safety of all underground instrumentation and uninterrupted central power supply from the surface. All abnormal and critical states are signalled to the mine control room. These trigger alarm and emergency procedures. The computer based ventilation monitoring and control system also performs the function of an expert system for fire detection and underground fire fighting. The mine control operator (dispatcher) makes use of stored data in computer escape route schemes and procedures for the safe withdrawal of miners from hazardous areas. The operator can put in motion intrinsically safe alarm signalling units and banners with programmed messages indicating escape routes.

Jan 1, 2005

By Seymour C. A

Peak Downs Mine, a five million tonnes a year coking coal operation, strip mines a, series of Permian coal seams. Seam thickness ranges from 0.5m to 5.0m, and seams consist of multiple coal plies with intermediate shale and mudstone partings. Four 47m3 draglines strip overburden to a cover depth of up to 60m. Coal loading is by 12m3 shovels and 14m3 to 18m3 front-end loaders. Parting removal takes place where the layer of shale and mudstone between seams exceeds 0.3m in thickness. Parting has been removed by a wide variety of earthmoving equipment in order to evaluate the problem and to select the optimum method from an operational and economic standpoint. Multi-seam stripping of the thicker seams is accomplished by working draglines from spoil- pile benches. Coal seams thinner than lm are recovered by dragline and stacked in the pit for later loading.

Jan 1, 1974