Search Documents

One of primary causes of poor blast performance is the improper relief of explosive energy. Under or over-confined blasts modify the explosiveÆs path of least resistance, which changes where and when the explosive energy is applied resulting in less than optimum blast performance. During the research for this paper the overbreak characteristics of five full-scale blasts were quantified using high speed cinematography and borehole cameras. The effectiveness of various overbreak control methods was also evaluated to guide design refinement. The results of this research along with general recommendations for reducing excessive damage are included with this paper.

Jan 1, 1999

A resume covering currently accepted views on blasting vibration measurement, human response, and criteria for damage is presented as background information for readers who are not conversant with blasting vibrations. This is followed by sections on vibration level estimation and blasting techniques to control vibration. Emphasis is placed on making use of the scatter in the delay intervals of half-second delay detonators, the use of smaller explosive charges for early delay numbers, and the non- use of zero-delay (instantaneous) detonators in cer`a. n cases.

Jan 1, 1976

By Geisler P, Sutherland P

The technical limits for high-pressure transport of large particle solids by means of sludge pumps, piston pumps or the like lead to the development of the pipe-feeder system. The pipe-feeder is a type of pressure lock in which the high-pressure pump itself is not in contact with the solids. Simultaneous operation of the three chambers with corresponding control of the valves allows continuous flow in both the primary and secondary circuits. Initially the pipe-feeder was used only for the transport of solids. Today it also operates with great success in central mine cooling systems, serving as an alternative for high-pressure/low-pressure heat exchangers or Pelton systems. In addition to the technology applied up to now, the pipe-feeder is also capable of transporting ice slurry, thus increasing cooling output consider- Ably.

Jan 1, 1991

By Tuite M. J, Woolcock L. J

The Awak Mas gold project is located in the Province of South Sulawesi, Republic of Indonesia. It is situated 300 km by road north of the provincial capital of Ujung Pandang. The capital is readily accessible by air from Australia via Denpasar on Bali or the Indonesian capital, Jakarta (Figure 1). Elevations at Awak Mas range from 850 to 1400 metres above sea level in reasonably rugged terrain. The area is covered by primary and secondary (regrowth) rain forest. The region is subject to an equatorial-type tropical climate. The annual rainfall is a high 3000 mm most of which falls in the rainy season between March and June. In the lower valleys rice, cloves and chocolate crops are cultivated. Title to the project area is secured by a Contract of Work (COW) issued to PT Masmindo Eka Sakti (MES) on 23 October 1987 by the Government of Indonesia. MES was controlled at the time by New Hope Industries group of Brisbane. After New Hope had completed initial reconnaissance exploration of the area, Battle Mountain Gold Company (BMGC) farmed-in in 1991 and earned a 60 per cent beneficial interest in MES.

Jan 1, 1996

By Shining Z

The properties of coal or rock containing gas are very important both for studying coal and methane outburst mechanism and for controlling underground rock in mining. The rheological fracture properties of coal containing gas were studied to obtain its rheological fracture principle both in microscopic scale and in macroscopic scale. The application of this principle is successful in explaining coal and methane outburst mechanism and for putting forward a rheological hypothesis of coal and methane outburst.

Jan 1, 1992

YOUR Excellency, Fellow Members of the Australasian Institute Of Mining Engineers and Gentlemen:- Nearly a decade has passed, since our Institute first met in New Zealand. May I, at the very outset of this second gathering, congratulate the Institute on the great progress that has been made in the interval. At the first meeting in New Zealand in the year 1903, I understand that less than 20 persons were present, and now in the large concourse before me I believe there are not fewer than 140 persons, while if every member of the Institute to-day where here there would be over 500 which is a great change from a membership of only 250 in 1903. I feel deeply appreciative of the honour you have conferred upon me by electing me your President for the year 1911. In return for the compliment, may I ask you to believe that I shall do everything in my power to further the interests of the Institute throughout the coming year.It is a great regret to me to realise that soon my work in New Zealand will be over. However, I trust that the new...

Jan 1, 1911

By Morrison R. S, Doennilan N

Recent mapping (1989-1992) by the Northern Territory Geological Survey in the Tennant Creek 1:250 000 map sheet area has resulted in substantial revision of the lithostratigraphy of the Tennant Creek Block (Donnellan, Hussey, and Morrison, in press). Briefly, the former Warramunga Group (Dunnet and Harding, 1967; Dodson and Gardener, 1978) is divided into the Warramunga Formation, and an overlying less deformed volcano-sedimentary succession, the Flynn Subgroup. The latter is conformably overlain by the Tomkinson Creek Subgroup of the Tomkinson Creek province in the north of the Tennant Creek Inlier. These two Subgroups constitute the Churchills Head Group which is essentially equivalent to the Hatches Creek Group of the Davenport province to the south of the Inlier.

Jan 1, 1994

By M Battersby, F Parra, S Sanchez-Pino

Pneumatic flotation, as developed by Dr Rainer Imhof, has been applied in commercial beneficiation operations since 1987. Over 85 flotation cells have been installed in more than 30 operations, successfully beneficiating a wide range of minerals. Pneumatic flotation is however still considered as a non-conventional flotation process. Due to its highly selective nature in operation it has generally found its market in difficult applications where conventional flotation equipment has struggled. Compa±fa Minera Huasco (CMH) operates an iron ore pellet plant in central Chile. CMH desired to produce a low silica pellet for the export market where the SiO2 grade should not exceed 1.5 per cent. It is common practice in other countries to float quartz from hematite with relative ease. However, the silicates contained in the magnetite ore of CMH are only present as quartz in small quantities and the major undesirable silicates are difficult to float. CMH spent considerable time on developing a reverse flotation process and a reagent suite to try and reduce the silica content to acceptable levels. However, extensive laboratory and pilot plant tests with conventional mechanical tank type cells and with column cells failed to produce the required reduction in impurities. A series of tests with pneumatic flotation cells indicated that this type of flotation technology could achieve the required silica target. A 500 tph Imhoflot pneumatic flotation plant was subsequently constructed and successfully commissioned by CMH, making it one of the largest iron ore flotation plants in the world. This paper details the background and testing that was undertaken by CMH which led them to choose pneumatic flotation as the preferred process and compares the test results with that achieved in the industrial plant.

Jan 1, 2005

By Sobek S, Lotzien RM

Although the conventional procedures for designing agitator flotation plants are well-known and reliable, little experience for designing modem pneumatic flotation plants has been gained up to now. A reliable procedure originating from graphic methods for the design of distillation columns is presented. Examples demonstrate on laboratory and semi-technical scale the application of this extremely practical method for designing a fly ash and a magnesite flotation plant.

Jan 1, 1993

Hamersley Iron Pty. Limited mines and pro cesses iron ore from two orebodies at Tom Price and Paraburdoo, situated in the North West of Western Australia. Conventional open pit mining methods are used at both sites in that material is drilled and blasted in benches, loaded by shovels and hauled to the Primary Crushers or dumped on waste or low grade material stockpiles. The present drilling fleet, consisting of eight high capacity Bucyrus Erie Rotary drills has evolved from an initial fleet of a large number of small percussion rigs. There are significant physical differences between the ore types encountered at both mines which nec- essitate the drilling of smaller diameter blast holes at Paraburdoo than those at Tom Price. The drilling practice at each site is dis- cussed, with examples of performance achieve- ments under varying drilling conditions.

Jan 1, 1978

By J B. Holman, P A. Weber, P Lindsay

Underground and opencast coal mining has occurred since 1896 on the Stockton Plateau, West Coast, New Zealand. Acid Rock Drainage (ARD) from historic and current mine workings has had an adverse environmental impact on the surrounding aquatic environment. The two main catchments affected by ARD from historic and current mine workings are the Mangatini and St Patrick Stream catchments. Solid Energy New Zealand Ltd (SENZ) is using active (e.g. alkali dosing) and passive (e.g. engineered cover) technologies to mitigate the adverse environmental effects associated with ARD contaminated waterways. This paper discusses the passive technologies. Principal strategies include the capping of high capacity potentially acid-forming volumes of overburden. The mudstones were found to generally have the highest sulphur levels compared to other overburden lithologies. Areas with high mudstone volumes are prioritised to be encapsulated and 390 Ha is planned to be capped in the Mangatini catchment in the near future.   Monitoring beneath granite, cement kiln dust and coal combustion product covers show oxygen can be reduced to less than 10% of atmospheric levels. Laboratory column leach tests that were subjected to oxygen flux rates of 10 % showed reducing oxygen ingress into acid-forming material can result in significant acid load reductions.   The oxygen content below the cement kiln dust cover was generally lower than 5% and water quality measured in lysimeters beneath this cover improved after 50 weeks of emplacement. Column leach tests containing saturated samples were undertaken to determine the most appropriate water medium in preventing pyrite oxidation. The sample saturated with ARD (pH ~ 3) had a negligible acid production rate and leached very minor Al concentrations although Al is soluble at low pH. This indicated saturating waste rock dumps with ARD can be an effective method in mitigating ARD formation.

Jan 1, 2007

By Collins DN, Hollick CT

Conventional processing of heavy mineral deposits containing radioactive rare earth minerals such as monazite and xenotime may cause industrial hygiene problems through atmospheric dust and contamination of product concentrates. An alternative procedure has been developed in which such minerals are removed from bulk heavy mineral concentrates by flotation with little loss of other economic minerals. With fine ores, recoveries of over 95% have been achieved and with coarse ores over 80%,in both cases at high grade. Several flotation regimes have proven effective. The potential for generation of radioactive dust or product contamination is subsequent processing -is correspondingly reduced.

Jan 1, 1990

By D R. Swinbourne, Y H. Yang

Calcium ferrite slag has gained prominence in the copper smelting industry over the last decade due to the emergence of continuous converting as an established technology. As smelters move towards processing which is higher in intensity, more efficient and more environmentally acceptable, its use is likely to increase because it has technical advantages over conventional iron silicate slag, which include a higher magnetite-holding capacity, lower copper losses to slag and a lower viscosity. Calcium ferrite is currently the converting slag of choice in the Mitsubishi process at operations in Japan, South Korea, Indonesia, Canada and Australia, and in the Kennecott/Outokumpu flash converting process in USA. However, users of this slag have experienced problems in containment due to its highly corrosive nature and low viscosity. As use of this slag becomes more widespread the containment problem will assume greater importance. Consequently, work has recently been carried out to establish the mechanism of refractory attack and devise means to retard it. This work will be critically reviewed in this paper.

Jan 1, 2000

By E E. Hall, C D. Taylor, D S. Yantek

Regular monitoring for methane gas is required near working faces in gassy underground mines where the potential for methane ignitions is greatest. However, high concentrations of methane can also accumulate outby the face where methane levels are monitored less frequently. Wearing a personal methane monitor equipped with an alarm could protect persons working in these outby areas from injury or death due to methane ignitions. The National Institute for Occupational Safety and Health (NIOSH) has conducted studies to evaluate methanometers that could be used as person-wearable monitors. For the present study, seven different person-wearable monitors that are not currently approved for underground use were evaluated. This paper describes test procedures used to evaluate performance of methane monitors that could be used underground for continuous personal monitoring of methane. The information in this report provides data that allows the reader to make side-by side comparisons of these instruments.

Jan 1, 2005

Introduction.History of Stope Filling at Mount Isa.The Need for a Systematic Fill Programme.Reasons for Filling.Fill Materials and Tonnages.Rough Mullock Fill.Quantities Readily Available.Fill Pass Development.Stope Preparation.Drainage.Hydraulic Sand Fill.Initial Experiments with Mill Tailings.Surface Layout.Operation Procedure.Underground Pipe Lines.Life of Sand Pipes and Cones.Drainage.Old Tailings Dam Sands.Quantity of Fill Placed.Pillar Tonnages.Conclusion and Acknowledgment.INTRODUCTIONFilling practice outlined in this paper refers exclusively to the Black Star section of the mine. The stope filling necessary early in the life of the Black Rock and portions of the Rio Grande sections is not to be confused with the current filling programme.

Jan 1, 1953

The Argyle Diamond Mine came on stream late in 1985 as the world's largest diamond producer in terms of carat output. The design of the process plant, including the heavy medium separation (HMS) facility which provides the initial stages for separation of diamonds from gangue, evolved over a lengthy period of feasibility study and site investigation into the final form described in this paper. The commissioning was carefully planned and co-ordinated, and culminated successfully with handover of the plant on schedule and within budget. Problems encountered during .within were minimal and since then the plant has achieved greater than design throughput during its first year of operation. Darvr_ontmn

Jan 1, 1987

By Jacobs M

After a methane explosion in a coal mine a pre-determined crisis management procedure is instigated. As the process rapidly evolves the inevitable question arises - are personnel trapped underground, are they alive and can they be rescued without putting the lives of the rescue crew at risk? This is a very emotive question with many sub-questions such as; could anybody have survived, is there the potential for a secondary explosion and is there a `window of opportunity' before that secondary explosion occurs?To determine if that window of opportunity exists two fundamental elements must be in place; a method of determining the atmosphere at key points in the mine and a method of predicting the course of change of that atmosphere with respect to time. The first element can be achieved if the tube bundle system is intact and drawing samples from known points, alternatively boreholes can be drilled from the surface. The second element can be realised by utilising a sequence of computer generated control charts which have a time axis, a percentage combustibles axis, the upper and lower explosive limits of the current atmosphere and a prediction option which allows the user to look at the potential changes in the atmosphere over a set period of time. These control charts would be part of the mines on-going crisis management system rather than a tool to be used after an explosion had occurred.

Jan 1, 1998

This paper discusses considerations to be made for the selection of rock tunnelling machines, as opposed to drilling and blasting. A systematic approach is presented in terms of utilizing data frcm site investigations to accurately forecast machine performance for estimating and planning purposes and to help minimise associated risks. Useful rock index properties are identified, and correlations for predicting advance rates for roadheader and full face machines are presented together with a simple method of characteristing rock mass conditions for estimating machine utilization and the savings to be gained in support costs. Finally considerations for tunnelling in adverse ground, for advance probing and for large sized tunnels are outlined.

Jan 1, 1987

By Crawford J

The paper asks the question 'Why Limit the HYDROTRANSPORT of material to the confines of your washplant'.A brief historical review of widely accepted slurry transport operation establishes that we are not talking about new technology - simply applying proven experience to an innovative continuous system.The paper reviews a simple potential application and compares capital and operating costs with conventional trucking.No attempt has been made to develop a complete mine plan and the comparison has been limited to material transport costs.

Jan 1, 1992

By Floyd J. M

The recovery of gold from refractory ores and concentrates can be achieved in a number of ways using roasting and leaching procedures. The Sirosmelt system introduces a new approach to the recovery of gold from these materials using smelting procedures. Laboratory studies were carried out to establish procedures for operating the Sirosmelt system for recovery of gold and associated valuable elements from an ore containing 17.5 g/t gold and a concentrate containing 22 g/t gold as well as substantial copper levels. Copper, iron, lead and matte were evaluated as collecting phases for the gold. The ore smelting procedure recovered 80-90% of the gold whilst smelting concentrate gave 98-99% gold recovery.

Jan 1, 1987