Search Documents

By T W. C Stambolie

Coalmines, like any other mine, generally involve the classic three-staged approach to mining studies; namely concept, pre-feasibility study (PFS) and feasibility studies (Cusworth, 2012). Subsequent to these studies, and in instances parallel to these studies, the commitment to an environmental impact statement (EIS) is made in order to secure both state and federal development consent. In recent times, the sentiment to both mining and coal is changing whereby the traditional approaches to mine planning and economic evaluation is complicated by evolving environmental legislation, expectations and time frames. It is all too common to take shortcuts in the development of projects in order to create the perception of cost savings and expediting the delivery timeline. Atkins (2016) points out that: boards of so many small to mid-tier mining companies, and a few majors, focus on relentless project delivery too early in the project process, with so little time and effort applied to risk analysis and option development. Unforeseen risks can cost any timeline or budget far more than the effort required assessing and mitigating these. The ultimate risk to any feasible coal project is that of environmental approval and achieving development consent.CITATION:Stambolie, T W C, 2016. A black canvas – planning a greenfield coalmine in New South Wales, in Proceedings Life-of-Mine 2016 Conference , pp 31–35 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By C Li

Removal of gangue minerals from ilmenite concentrates can be accomplished by relatively low temperature roasting in controlled gas atmospheres to selectively enhance the magnetic separation characteristics of the ilmenite. At roasting temperatures below 800¦C the magnetising reactions are often not consistent with phase equilibria considerations. Metastable phases can nucleate and control the roasting products. In weathered ilmenites the phase assemblages and microstructures in the altered ilmenite grains can influence the roasting reactions. In this paper we give an overview of the phase chemistry of chemically weathered ilmenites and of metastable phases formed by low temperature roasting. We also report the results of roast experiments conducted in a neutral gas atmosphere. Major increases in magnetic properties after short roasting times at low temperatures were obtained for a range of ilmenite concentrates. For example heating a secondary ilmenite concentrate from Western Australia for 15 minutes in nitrogen at 600¦C gave an increase in the three kilogauss magnetic fraction from three to 92 wt per cent. The solid state phase changes accompanying the inert atmosphere roasts were characterised by combining elemental analyses with quantitative phase analyses of the ilmenite concentrates and their roast products. It was found that the phase reaction that is principally responsible for the increase in the magnetic properties of weathered ilmenites involves a transformation of disordered ferrous-containing pseudorutile to an ordered ilmenite-hematite solid solution containing typically ten to 35 mole per cent of the hematite component. Examples are given of the application of the inert atmosphere roast to effect separations of ilmenite from gangue minerals.

Jan 1, 2001

By D L. Head

Critical risk management (CRM) has become one of the latest safety buzz terms in mining. Everyone seems to be doing it, everyone seems to know about it, yet we are still having fatalities in our industry from well understood hazards such as mobile equipment amongst others.

May 5, 2022

By B Dold

"Mining has still today high potential for improvement in the exploitation efficiency. Especially low-grade ores have very low recoveries. In Cu bioleaching operations from porphyry copper deposits extraction of only five and 15 per cent with maximum of 40 per cent are reached. This means that 60–95 per cent of the resource is not exploited. Consequently, any metal not extracted will end up in the waste material, therefore increasing the risk of environmental pollution. This inefficiency is mainly due to the use of element concentrations for decision-making on the daily basis of a mining operation (eg cut-off ore grade, acid-base accounting – ABA). If, instead, quantitative mineralogical and geochemical data together with information on the bioleaching behaviour of the ore assemblage (the biogeometallurgical approach), is used for decision-making right from the beginning of the exploitation, higher recoveries and less environmental impact can be achieved, ie an increase in sustainability can be reached.CITATION:Dold, D, 2016. The Biogeometallurgical Approach – the Information We Need to Increase the Sustainability of Mining, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 169–172 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By C Wu, H Chen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.The Halasu porphyry copper belt, located in the East Junggar basin bounded by Chinese Altay to the north and the Tianshan mountains to the south in the Central Asian Orogenic Belt, is one of the major porphyry copper belts in Xinjiang province, north-west China. Combined with previous studies in this area, the magmatism can be divided into three periods: pre-mineralisation activity of 390 Ma syn-mineralisation activity of 380–370 Ma post-mineralisation activity of 360–330 Ma.Through the comparison of zircon chemistry from ore-bearing and barren syn-mineralisation intrusions, negative correlation was identified between Ti-in-zircon temperatures and oxygen fugacity, corresponding to the fact that late-stage syn-mineralisation granitoids contain high water content, high oxygen fugacity and low temperatures with higher mineralisation potential. In addition, the relative low initial 87Sr/86Sr ratios, high eHf(t) and eNd(t) values and mantle Pb isotope characteristics in this study support that the magma forming these intrusions was probably derived from juvenile crust generated during subduction-accretionary processes.CITATION:Wu, C and Chen, H, 2015. Zircon trace elements and Sr-Nd-Pb-Hf isotope systematic of the Halasu porphyry Cu belt, north-east Xinjiang, China, in Proceedings PACRIM 2015 Congress, pp 637–640 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By D Hatton, S Wilson, F Orrante, M Taghimohammadi, F van der Walt, N Arslan, M Westcott

"Cayeli Bakir Isletmeleri is an underground copper-zinc mine in turkey. The ore is highly variable with feed grades ranging from 1–4 per cent copper and 1–10 per cent zinc. Due to this variability, ore characterisation and blending strategies are crucial for performance optimisation.This paper presents a case study for a multidisciplinary approach to process optimisation, integrating Geometallurgical and advanced control methods to achieve optimised plant performance. The results from comprehensive metallurgical tests and surveys were used to develop a mathematical model utilising SGS’s Integrated Geometallurgical Simulator® (version number 2.5.24.0). The model was employed to determine the most appropriate operational settings required to ensure that optimised grades and recoveries are achieved for each ore type.SGS’s Modular Expert Technology (MET) expert system was then implemented to target these optimum operational ranges utilising online grade and froth velocity measurements. The successful conversion and deployment of the modelled process parameters into an expert system has resulted in significant improvements in overall recovery and circuit stability.Citation:Arslan, N, Westcott, M, van der Walt, F, Hatton, D, Taghimohammadi, M, Orrante, F and Wilson, S, 2016. A Multidisciplinary Approach to the Optimisation and Control of a Copper-zinc Grinding and Flotation Circuit, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 115–122 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

Driefontein Gold Mine together with Kloof Gold Mine and Beatrix Gold Mine forms part of Gold Fields South Africa. Driefontein Gold Mine is situated near the town of Carletonville, 50 km south of Johannesburg, in the Gauteng Province. The 4 Shaft East complex comprises of the 4 Main Shaft and the 4 Subvertical Shaft. The main shaft is 9150 m in diameter and was sunk in 1984 to a depth of 2000.5 m. The 4 Subvertical Shaft is 7320 m in diameter and was sunk during 1985 to a depth of 3006 m. Full production was, however, only reached during 1988. Intensive mining is currently being done between levels 28 to 42. In 2002 a decision was made to start mining the shaft pillar, situated between 32 and 33 level in the subvertical shaft. Intensive studies showed that with selective mining scheduling the total mineÆs life could be lengthened by nine years if accessed timeously. The higher grades present in the shaft pillar can be mixed with lower grades from the same reef band presently mined 1500 to 2000 m away from the subshaft pillar area. The shaft pillar comprises 50 per cent of the remaining ore resources available. However, no provisions were made in the initial phases of the shaft development to extract the shaft pillar. Grades between 4300 cmgt to 2500 cmgt relating to 23 and 14 g/t are present in the shaft pillar and an estimated 50 tonnes of gold can be produced from this pillar in the period from 2007 to 2015. The pillar extraction is the key to DriefonteinÆs long-term gold profile. Every geological feature possible is represented in this to-be-mined pillar area. The pillar around the shaft is a complex structure featuring hard and soft lava, sedimentary structures/plane parting that moves against each other, quartzite capping, etc. Replacement of services and secondary support systems were designed, modelled and put in place. The original steelwork was not designed to cope with the various stresses and movements, which are expected once the extraction process is started. Existing shaft steelwork was used as far as practically possible. The principal behind the design was that the steelwork would be totally disconnected from the shaft lining over its total length of 132 m in the area of the reef intersection. This will allow the steelwork to move independently from the geological structures surrounding it, allowing a certain degree of distortion of the shaft lining, moderate twist and tilt to take place without interfering with hoisting operations.

Jan 1, 2005

By M Nehring, M Kizil, P Knights, A Mousavi, F Sotoudeh

A cut-off grade is used to distinguish an economically viable block of ore from non-economical ones in mining operations. In order to obtain a high Net Present Value (NPV), a strategic and precise determination of cut-off grades (mill feed/marginal, marginal/waste) is required. In recent years, the significant depletion of feed grades and increasing mining operating costs have affected the viability of new and existing mining operations. Hence, the introduction of a pre-concentration system to process ore before sending it the main processing plant has gained increasing attention for its potential improvements in resource exploitation processes, mineral processing, energy consumption and environmental impacts. The primary potential advantage of implementing a pre-concentration system is the improvement of resource utilisation and increased reserves as a result of a reduction in cut-off grade. The objective of this paper is to present a new cut-off grade method, which can be used in the presence of a pre-concentration system for underground metalliferous mining operations. The results of this study illustrate the potential economic benefits of using a pre-concertation system prior to a mineral processing operation as a result of the reduced cut-off grade and increased NPV.

Nov 10, 2020

By D Joshi, J Rostami, M Karakus, A Eustes

The first target of mining activities on the surface of the moon is to find and extract water from the icy regolith on the moon. A test drilling unit was designed and fabricated under a NASA Early Stage Innovation (ESI) grant. A high-frequency data acquisition system was used to record drilling responses at 1000 Hz. Parameters like weight on bit (WOB), torque, rev/min, rate of penetration (ROP), mechanical specific energy (MSE), field penetration index (FPI), and the uniaxial compressive strength (UCS) were recorded for 40 boreholes in the analog samples made of regolith simulant and specialised cement. Development of the AI system and machine learning (ML) algorithms for analysis of data to evaluate strength and hence water content of icy regolith required a large data set. In this case, the data set comprising of more than one billion data points recorded while drilling into various analogue samples and cryogenic lunar formations to optimise power consumption and make bit wear adjustment during drilling operations. The tests were also repeated in the samples of icy regolith at various water content at -190C to verify the ability of the algorithms to analyse the data and to estimate the strength of the frozen formation and hence water content. The paper will discuss the objectives and methodologies used in the project and reviews the testing program and the machine learning (ML) algorithms ability to identify various formations along the exploration boreholes.

Sep 1, 2024

By T R. Anderson, A R. Butler

Haymont (2012) notes that in parts of Australia significant areas of mining disturbance cannot be relinquished. In Queensland it has been estimated that by 2010, just 0.3 per cent 507 ha of mining disturbance had been rehabilitated to the regulator’s satisfaction (Short, 2015).One reason for this poor record is the presence of inappropriate, unachievable or unmeasurable rehabilitation targets (Glenn et al, 2014; Butler, Anderson and Sexton, 2015). In the authors’ experience in Queensland many mature operations have licence conditions that hinder the achievement of sustainable outcomes or prevent successful validation of rehabilitation success. This creates a lack of certainty for industry and a lack of confidence in the community that the sector can deliver good rehabilitation outcomes (Short, 2015).This extended abstract presents a framework approach that has been applied at two contrasting operations. Without the changes presented, the goal of progressive rehabilitation certification, reduction in financial assurance (FA) and a path to surrender at these sites would have been impossible. The framework can be adapted for use across different bioregions and commodities.CITATION:Butler, A R and Anderson, T R, 2016. Reassessing rehabilitation objectives and targets for mature mining operations in Queensland, in Proceedings Life-of-Mine 2016 Conference, pp 139–141 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By J R. Taylor, J A. Muchan, S M. Pape, B S. Davis

Acid and metalliferous drainage (AMD) is routinely derived from waste rock, tailings, pit wall rock, underground mine voids, heap leach pads, ore stockpiles, concentrate stockpiles and even slag piles. In many jurisdictions, there is an assumption that tailings materials represent the highest AMD risk. This is likely due to their highly sulfidic and ultra-fine grained nature, and the fact that they occur in large tonnage, partially unsaturated deposits. These characteristics are not unreasonably associated with reactive and therefore highly polluting mine waste materials. Interestingly, however, the high sulfide content and highly reactive nature of tailings achieves the rapid consumption of oxygen in tailings pore spaces. This oxygen depletion can limit or halt sulfide oxidation throughout much of the tailings pile. Oxygen can only be resupplied to the tailings via atmospheric exchange at the air-tailings interface. The grain size of most tailings materials limits this resupply to a diffusion related process that only affects the uppermost 100–2000 mm. Hence sulfide oxidation in tailings can be inherently self-limiting. Unfortunately, the same cannot be concluded for waste rock materials.Using a unique site assessment strategy that focuses on quantifying acidity fluxes from various domains at a mine site, it has become increasingly evident that sulfidic waste rock produces the majority (typically 60–80 per cent) of the soluble acid and metalliferous pollution at most active and decommissioned sulfide-bearing mine sites. Whether sulfidic waste rock is disposed in engineered above ground facilities, backfilled into pits or even underground voids, it remains the primary source of pollutants for decades to centuries.Conventional end-dumping waste rock practices result in angle-of-repose pathways for air and water, and these internal fabrics exacerbate sulfide oxidation (ie pollution generation) and discharge from waste rock materials. The primary aim of many cover systems is to retard the access of air and water to these conduits. Recent thinking is that more emphasis needs to be directed at strategic waste rock pile construction practices, and less reliance placed on thin soil cover systems to prevent AMD.Waste rock pile construction approaches that minimise porosity and permeability but raise the retained moisture content and enhance water residence times have the potential to lower sulfide oxidation rates and thereby improve water quality outcomes. For example, innovative base-up, layered and compacted (BULC) waste rock piles have the potential to avoid or minimise the generation of AMD, supersede the need for treatment and facilitate successful closure and relinquishment across the mining sector (Figure 1).CITATION:Taylor, J R, Pape, S M, Davis, B S and Muchan, J A, 2016. Waste rock pile construction to lower closure and relinquishment costs, in Proceedings Life-of-Mine 2016 Conference, pp 97–99 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By T Takayama, M Matsumura, Y Konno

The steel industry accounts for 14 per cent of domestic CO2 emission in Japan, and iron ore sintering process occupies approximately three per cent. While Fe content in iron ore is gradually decreasing. So, the amount of concentrated iron ore will increase in the future. We have focused on magnetite concentrate as sinter materials, because magnetite can be easily magnetically beneficiated. However, it is experienced that blending magnetite ore resulted in increasing Fe2+ component in the iron ore sinter, which results in lower reducibility. Therefore, promoting the oxidation reaction from magnetite to hematite in the sintering process is countermeasure for reducibility. In addition, this promotion causes increase of oxidation heat, which results in high sinter strength and reduction of coke. It is assumed that the oxidation of magnetite tends to proceed in the cooling stage, where the oxygen partial pressure increases after the combustion of fine coke, but there are few studies on the effect of heat profile, especially cooling path. The purpose of this study is to design the effective sintering heat profile to promote oxidation of magnetite ore, especially, to investigate the effect of cooling path on sintered ore microstructure. In this study, magnetite ore and magnetite reagent were respectively mixed with calcium carbonate reagent. Then the mixed samples were pressed and formed into cylindrical tablets for simulating the adhesive layer of a pseudo particle. Through examining influence of maximum temperature and cooking rate on oxidation reaction of magnetite, we confirmed that the oxidation reaction of magnetite is suppressed at above 1350°C for maximum temperature, compared to 1300°C. Sintering at lower temperature is desirable because hematite is stable below 1350°C in the Fe2O3-CaO phase diagram.

Nov 8, 2021

By Ricketts N. J, Smith G. D J

A hydrometallurgical process was developed for recovery of copper from copper-lead matte formed as an intermediate product at the BHAS lead smelter at Port Pirie. A plant utilizing this process was commissioned in 1984. The leach step involves oxidation of the copper-lead matte in an oxygenated acidic chloride-sulphate leachant. The results of laboratory scale testwork from which the chemistry of leaching was deduced, are presented in this paper. The rate of recovery of copper to solution from copper-lead matte depends largely_on the availability of oxygen to the sulphide surface. The optimum leach temperature is approximately 85¦C. Free acid must be supplied according to the stoichiometry of the leach reaction: Cu1.91 S + PbS + 2.91 H2SO4 + 1.455 02 = 1.91 Cu2+ + 1.91 SOj- + PbSO4(s) + 2.91 H2O + S¦ The grind size of the matte is of minor significance. Chloride concentration in leachant should be at or above a minimum of 10.0 g/l. Chloride acts to complex cuprous ions formed during leaching.

Jan 1, 1987

By H Indirawati, R Ayres, A Nur Kasnanto, S Konopa

As a project moves through the mine life cycle, the quantity of data available increases and the understanding of the orebody matures. Incorporating new information quickly and efficiently in current 3D models, is essential for adding value across the life-of-mine value chain. At the Martabe Gold Mine, the resource development group manages 14 drill rigs on six resource projects, including three operating mines. The Martabe deposits are geologically complex and the volume of new information that becomes available each day is substantial. It is imperative that new geological and assay information is integrated into the 3D models as soon as possible, so that drill planning and targeting can be modified accordingly. Martabe uses Leapfrog<sup>®</sup> 3D software to update and interrogate the 3D models on a dynamic basis as data becomes available. This results in faster and more effective changes to drill planning and schedules. The impact of this is better drill productivity and cost savings due to optimal drill targeting, and availability of up-to-date models incorporating the most current data. CITATION: Konopa, S, Ayres, R, Nur Kasnanto, A and Indirawati, H, 2018. Optimised drill targeting using dynamic 3D modelling, Martabe Gold Mine, Indonesia, in Proceedings Complex Orebodies Conference 2018, pp 99–101 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By M de Freitas Silva

One of the main steps during the decision-making process of long-term mine planning is the definition of the optimal sequence of extraction, which usually is synonymous with maximising the discounted cash flow of the project subjected to several constraints arising from aspects of technical, physical, and economic limits.Open pit mine production scheduling (OPMPS) comprises several intricacies related to its size and uncertainty of input parameters. Due to its complexity and prohibitive size, traditional mine planning usually relies on heuristic or metaheuristic methodologies which are able to provide good solutions in a reasonable amount of time. However, most of the uncertainty that surrounds the mining complex is ignored leading to non-realistic results.In this paper, a new heuristic approach is explored in order to solve a stochastic version of the OPMPS problem accounting for geological uncertainty in terms of metal content, multiple processing streams, and stockpiling option. The methodology involves generating an initial solution by solving a series of subproblems and this initial solution is improved using a network flow based algorithm.The algorithm was applied to a relatively large gold deposit with more than 119 thousands blocks. Results have shown that the methodology is promising to deal with large-size mine instances in reasonable time.CITATION:de Freitas Silva, M, 2014. Solving a large stochastic integer programming model for production scheduling at a gold mine with multiple processing streams and uncertain geology, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 389–396 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By O A. Aladejebi, S Mitra, T Singh, D O’Dea, S, T Honey

Granulation of the iron ore blend and the additives is the foremost step in the agglomeration of iron ore fines to achieve a permeable bed during sintering, which is crucial for sinter productivity. This study investigated the granulation of four types of blends to determine the impact of granulation on bed permeability. The blends were granulated in a rotating drum at various moisture contents and their JPU permeability was measured at each moisture content in a permeability pot (diameter 95 mm and height 500 mm) at various flow rates. Several independent experiments were carried out to investigate the changes in permeability when mixtures of different particle size range (-1 mm and +1 mm) were introduced into a packed bed with a larger particle size range (-6.3 mm to +4.0 mm). The results revealed that the addition of particles in the -1 mm size range had a more pronounced negative impact on permeability compared to particles in the +1 mm size range. This can be attributed to the relatively higher energy losses (mainly inertial) associated with the presence of -1 mm particles in the mixture. The findings were used to quantify the granulation process based on the -1 mm particle size fraction in the granulated mix and their utilisation (denoted by UI-1 mm). For achieving optimal permeability in a specific blend, it was found that a UI-1 mm (utility index of -1 mm particle size) ranging from 0.82 to 0.92 was required. However, exceeding a UI-1 mm value of 0.95 resulted in weaker granules prone to deformation and led to decreased bed permeability. The study also showed that the UI-1 mm was highly dependent on the water addition per kg of -1 mm in dry feed and suggested adding ~80 to 110 mL of water per kg of -1 mm in dry feed to attain the best possible permeability. Additionally, the research proposed a mechanism involving the melting of granules at high temperatures and highlighted the influence of -1 mm particles on bed permeability during the sintering process.

Sep 18, 2023

By P Marianelli, J Theiler, B Beamish, A Spillman

The presence of reactive pyrite in waste rock contributes to the hazard of spontaneous combustion in emplacement facilities as it acts as an initiator of self-heating at low ambient temperatures. Organic carbon also present in the waste rocks acts as a fuel at elevated temperatures above 120°C and can lead to thermal runaway resulting in eventual ignition. A new laboratory test method (adiabatic incubation testing) is now available that can identify the presence of reactive pyrite and quantify the self-heating behaviour of the waste rock. McArthur River Mine has a waste rock profile that contains pyritic shale units, which have created spontaneous combustion events in the past. A systematic sampling and testing program is underway to characterise the spontaneous combustion hazard likelihood of the McArthur River Mine waste rocks to provide a sound database for future mine planning of the waste removal and emplacement. This paper presents some initial outcomes of this program and shows the leading practice in spontaneous combustion hazard assessment and management that has been adopted at McArthur River.CITATION:Beamish, B, Marianelli, P, Theiler, J and Spillman, A, 2018. Spontaneous combustion hazard assessment of McArthur River Mine waste rock, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 422–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By M Stephens, T A. Sutra

Currently, there are several open pit mines with production rates of about 200 000 tpd of ore that are reaching the end of their economic lives. In most cases, the remaining orebody extends to depths greater than 300 m below the pit limit, leaving hundreds of millions of tons of reserves that can only be recovered by means of an underground mining method. One such method used for mass production is block caving. This paper presents a ventilation system for a four-zone block cave mine operation developed on a footprint 1000 m wide and 1200 m long. The system is designed for a mine with a nominal production rate of 120 000 tpd of ore using diesel powered units on the production and reduction levels. It discusses the air quantity requirements for the worst case scenario, which is anticipated to occur five years after the mine has reached its full production capacity. Finally, it summarises the results of computer modelling exercises that were carried out to determine an economic ventilation infrastructure that includes shafts, drifts, main fans, and ventilation control devices.

Jan 1, 2005

By M C. Ackland

The Grande Côte Mineral Sands Deposit (GCMSP) is located on a coastal mobile dune system in Senegal on the west coast of Africa. Senegal is a stable, democratic republic, having gained its independence from France in 1960. It has a population of about 12.5 million people. The dunes begin about 25 km north-east of Dakar, the capital city of Senegal, and extend northwards for more than 140 km. The mineralised dune system averages about 2 km wide with some areas extending to up to 4.5 km wide.Mineral Deposits limited (MDL), a Melbourne-based company with over 60 years operational experience in mineral sand mining in Australia, holds, through its Senegalese subsidiary MDL Senegal SARL (MDLS), a 25-year Mining Concession covering the deposits. The main heavy mineral (HM) areas identified to date are, from south to north, Mboro, Fass Boye, Diogo and Lompoul. Within the Mining Concession there is potential to identify additional resources beyond the limits of present drilling. The dunes are mobile or semi fixed, pale yellow in colour and overlie older white marine sands. The dunes range between 5 m and 30 m in height and the mineralised zones, which are essentially flat-lying, average around 15 m in thickness. The mineralisation consists, principally of ilmenite with accessory zircon, rutile and leucoxene. Zircon and ilmenite are the main commodities of interest.Independent consultants AMC estimated mineral resources for the four main deposits in 2006 of 1330 Mt of sand averaging 2.0 per cent HM at a cut-off grade of 1.5 per cent HM. At a cut-off grade of one per cent the resources were 3200 Mt averaging 1.5 per cent HM. All of the estimate was classified as Inferred Resources under the 2004 Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (JORC, 2004).Subsequent completion of infill drilling, sampling and assaying of the initial mining area, centred at Diogo, was completed in 2008, enabling a final dredge path to be designed and ore reserves estimated, based on a JORC compliant Measured and Indicated Mineral Resource. Infill drilling is continuing in the Lompoul and the results of this campaign will be included in the JORC compliant data base by AMC in April 2010 to enable the 15 per cent year dredge path and mine plan to be finalised.Development studies have shown that the project can be optimised as a dredging operation, with mineralised sand being treated in a conventional floating spiral preconcentrator, wet concentrator and dry mineral separation plant. Engineering work now substantially completed by Ausenco Limited (Ausenco) has developed the combination of some existing plant from MDL’s past operations, and new plant for the complete process from dredging to final product separation and grading. Testwork on a series of bulk samples has determined that the project can yield a high quality zircon product and an ilmenite product along with minor rutile and leucoxene.Work to date indicates a likely output of around 80 000 t of zircon in various quality streams (Primary, Secondary, Standard and Foundry Grades), around 550 000 t of ilmenite plus around 15000 t of rutile and around 12 000 t of leucoxene/secondary ilmenite. Planned zircon output would represent around 7per cent of the total world production, which would make the GCZ&IP a significant producer on a world scale.The studies have indicated capital costs to be in the range of US$400 M total operating cost (after completion of ramp-up) of around US$50 M - $55 M/a. Revenue is expected to be in the range $127 M - $157 M/a.

Oct 5, 2011

By P Mitchell, S Pushpan, G Ferres, K Bobbermien, L Hudson

"Falling commodity prices and a rising supply surplus have ushered in a period of restraint in capital project investment across the global mining and metals sector. Competition for capital project funding has seen fewer projects progress through investment gates and a stronger focus on projects that deliver gains in capital productivity and strategic outcomes.Over the course of the 2015 financial year, EY conducted a study of 108 projects in the global mining and metals sector (EY analysis; Larsson and Ericsson, 2014; SNL Financial, 2015). The projects studied were at various life cycle stages and related to the development of copper, iron ore, gold, coal, nickel and other commodities. Each individual project investment exceeded US$1 B, and the studied group represented a cumulative investment value of US$367 B.The research found that the majority of projects were delayed and/or over budget when measured against the initial estimates made during the early stages of the project life cycle. Of the surveyed projects, 69 per cent were identified as facing cost overruns with an average overrun of 62 per cent above the initial estimate and 50 per cent reported schedule delays, even after remedial acceleration initiatives.The analysis found that budget and schedule overruns could be attributed to five key causes:project management factorsstakeholder conflictsresource constraintsregulatory, and policy-related challengesunfavourable external environment.Improving project delivery performance starts with successful planning, followed by rigorous management during delivery. From global experience on large and complex capital programs, EY has observed a consistent theme of underinvestment and a lack of focus in three often-overlooked but critical areas:implementing effective governance and reporting frameworks with lead indicators that reliably flag emerging risks while they can still be mitigatedallocating adequate cost and time contingency to account for risks across the life cycleenhancing the value of contingency by aligning contingency plans with scenario plans.This paper explores the surprising findings of the study, proposes a root cause model and examines key considerations in applying these critical enabling techniques.CITATION:Hudson, L, Mitchell, P, Ferres, G, Bobbermien, K and Pushpan, S, 2016. Are your megaproject schedules and costs under – or out of – control?, in Proceedings Project Evaluation 2016, pp 75–85 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016