Search Documents

By M I. Pownceby, S Hapugoda, H Han, E Donskoi, L Lu

Iron ore sinter mineralogy and its associated macro-/micro – structure has a strong impact on sinter quality. At a macroscopic scale, sinter ideally consists of a strong, porous matrix which bonds relict ore nuclei together. Microscopically, the sinter matrix (solidified from the melt part of the initial sinter mix) generally consists of complex calcium ferrites known as SFCA, secondary magnetite and hematite grains (precipitated from the primary sinter melt), glass and silicates. Depending on the conditions under which the sinter structure is formed, two major forms of SFCA with different morphologies are generally recognised, ie fine micro-platy SFCA (usually termed SFCA-I) and coarse columnar/prismatic SFCA. Detailed optical microscope observations of several pot grate and compact sinter samples revealed the presence of a variety of fine, coarse and dense forms of both types of SFCA. The controlled cooling tests revealed that cooling rate has an impact on the form and size of SFCA crystals. In this work, EPMA analysis of SFCA compositions from a variety of pot grate and compact sinter samples are presented. Results show that the SFCA types exhibit a broad range of complex compositions within the system Fe2O3/CaO/SiO2/Al2O3/MgO/TiO2/MnO2. Although SFCA-I and SFCA are known to be crystallographically distinct and with different, well-defined ranges in composition, there was considerable overlap in compositions of the experimental sinter samples. The development of SFCA textures depend on several parameters including the local chemistry and conditions including the maximum temperature attained and the cooling rate, within the sinter bed, thereby suggesting that SFCA identification based on morphology alone may be erroneous.

Nov 8, 2021

Three separate and unconfined aquifers occur in the Hilton area, named relative to position in relation to ore horizons: Footwall Aquifer in the east; Ore-Zone Aquifer within the ore-bearing Urquhart Shales; and the Hangingwall Aquifer in the west.It is the on-going strategy it Hilton to drain the Ore-Zone Aquifer which occupies structurally- and sulphide-controlled leached zones in the steeply west dipping strata. The aquifer affects considerable ore reserves to 480 m below the surface. Dewatering began in 1976, and is essentially completed to 4 level (240 m below surface). Dewatering efforts are now based on 8 level (480 m below surface).

Jan 1, 1993

By G MacDonald, B Forsyth, D Corkery, T

An investigation was carried out at Diavik Diamond Mines Inc (DDMI) to identify and quantify the mechanisms through which ammonium nitrate (AN) was entering the mine discharge water. The goal was to develop and complete an investigation of the potential AN loss mechanisms in order to assess their contribution to ammonia in the mine water system. The initial phase of the project involved the collection and analysis of blasting and water quality data that were used to determine the mechanisms by which the ammonia enters the mine water system and to establish a baseline data set for comparison with results from future trials designed to reduce AN loss. Three potential options for reducing AN loss were identified through the first phase of the project. The second phase of the project involved conducting a series of monitored trials with changes made to the drilling and blasting process. The results of these trials were compared to the baseline data set to determine if the changes introduced for the trials had reduced AN losses while producing satisfactory blast results. This paper describes the process for the collection of the baseline data, provides an analysis of the resulting data, discusses the changes made to blasting operations in order to minimise AN loss and describes the results observed subsequent to these changes.

Jan 1, 2007

By Beamish B. B

In this study, a systematic examination of the scale and variety of micro-structures in coal using Scanning Electron Microscopy (SEM) has been carried out, using coal samples of differing stages of coalification from the Bowen Basin and New Zealand. SEM provides detail of various micro-structural features and shows that a variety of micron-sized fractures and cavities are present in coals. These are differentiated into three pore types: fracture porosity, phyteral porosity and matrix porosity. Fracture porosity is generally associated with bright coals (although it has been shown that micro-fractures are present in maceral fragments from the dull coal layers). Characteristically the macro- and micro- fractures form a continuous structural fabric through the bright coal layers and thus make a significant contribution to overall permeability. The macro- and micro-fractures appear to have been formed during the process of coalification rather than being formed due to shrinkage during methane extraction, as most of them are infilled with secondary minerals. In contrast, phyteral and matrix porosity is associated with the dull coal layers that are composed of plant fragments or a heterogeneous mixture of macerals. Like the macro- and micro-fractures, the continuity of the observed cavities suggest that these too are a significant contribution to overall permeability, and therefore play a major role in the transmissibility of methane at a level between diffusion at the micropore level and laminar flow at the macro-fracture level. Due to different spacing, orientation and persistence of individual fractures and cavities, the rate of methane transmissibility through a coalseam will vary according to coal rank, coal type and the organic precursors from which the coal was derived. This is important as a knowledge of the micro-structure system and its relationship to coal type and coal rank, plays an important consideration in: a) gas drainage modelling, b) enhancing permeability by inducing fractures and c) predicting the occurrence of outbursts.

Jan 1, 1991

By A Horeth, E Duggan, B Versiani, A Gooch

Iron ore screening plant productivity is strongly affected by the performance of the shuttle operation, with the control system robustness and associated strategies having a direct impact on utilisation and throughput rates. A number of aspects intrinsic to the methods and technologies traditionally applied on the motion control of shuttles are often observed to decrease the efficiency of the ore distribution process across multiple screening modules, which ultimately impacts the plant’s production. Those include the number of operational scenarios that are unmanaged by conventional discrete control logics which may intermittently lead to undesired events, such as ‘high level alarms’ and ‘low level interlocks’ in the screening bins. This outcome usually demands excessive manual intervention by Control Room Operators. A Reinforcement Learning (RL) Artificial Intelligence (AI) solution was deployed to control the motion operation of the scalping and products screening shuttles in an iron ore handling plant. The RL algorithm was trained in advance to handle multiple operational scenarios and generate optimised outputs. In nominal operation, the shuttles are moved in a modulating and highly predictive fashion over the whole range of safely reachable bins. When the need occurs, the AI control agent deviates from that modulation behaviour, limiting its travel range or moving to other groups or clusters of available bins by employing ‘bin jumping’ or ‘ore break’ strategies. The RL platform capabilities include the ability to learn in real time to account for and auto-adapt to new operational patterns and process changes whilst applying improved strategies for shuttle dwelling times, target setting and speed control. The deployed Reinforcement Learning AI solution has better managed the existing challenges associated with the shuttle operation and control, and resulted in a more efficient ore delivery process, superior operations stability and increased production rates.

Nov 8, 2021

Tunnels are being built around the world using TBMs and prefabricated segments or in situ concrete as linings. Clients demand high quality of these linings to guarantee a long-term stability and density of the tunnels. This paper describes the development and the use of segmental lining systems, including joints, important design criteria, installation procedures, possible mistakes and consequences, repair works and final results for different sites in Europe and around the world. The experience on these sites shows that damages may occur, if some essential aspects are not considered. These aspects include:parameters of the TBMs and back-up equipment such as fixation of jacking rams, movement of the back-up on the lining or ring reformer;parameters of the segments such as quality of moulds, quantity of reinforcement or structure of the joints; andparameters of the tunnel drive such as advance rate, ring-gap grouting or experience of the tunnel crew.All these aspects have to be considered very carefully in detail to get a good lining accepted in total.

Jan 1, 1999

The article, as written, represents a short account of the treatment of the base bullion from the Broken Hill ores, as carried on at Port Pirie, for the recovery of lead, silver, and gold, and for the treatment of by-products. Appended is a short description of the chief facilities of plant which have been adopted to overcome the main difficulties in the refining of lead the Howard press and stirrer. The article is within the limit prescribed by the regulation for the prize offered by the Australasian Institute of Mining Engineers, comprising 30 pages, containing an average of about 200 words per page, exclusive of analyses, photographs, and sketches.The writer desires to thank those to whom he is indebted for their- kindness in affording him every facility possible to obtain the information which he required for the success of such a paper-viz., Messrs. Robertson, Leavens, and Gronow, of the Broken Hill Propritary Co. Limited, at Port Pirie, and Mr. Crowther, of the Adelaide School of Mines, to whom he is indebted for photographs. The difficulty of obtaining fair samples of gold drosses, and the inability to obtain particulars of fuel consumptions, prevents the paper from being as complete as one would wish. The limited length precludes detail, except in more important parts.

Jan 1, 1907

By Read T. A

PART 1The quantity of dust present and the methods used for suppression of dust in metalliferous mines has, in recent years, received considerable attention from mining engmeers in various parts of the world. Shortly after the publication of the General Report of the Miners' Phthisis Prevention Committee, South Africa, in 1916, the officers of the Broken Hill South Limited started investigations into the conditions of the dustiness of the air in the underground workings. As the methods used are not generally known in Australia, the writers are of the opinion that the present is an opportune time to place them before members of the Institute. A large amount of the subject matter of this paper has been drawn from the 1916 and 1919 reports of the Miners' Phthisis Prevention Committee, South Africa, the paper of Mr. Innes published in "The Chemical, Metallurgical and Mining Society of South Mrica"; also various articles appearing in the Journal of Industrial Hygiene, and the American Journal of Public Health. A great deal of research work into the cause, prevention and estimation of mine dust has been made by the Miners' Phthisis Prevention Committee of South Africa, and officials of the United States Bureau of Mines. The writers considered it advisable to begin the investigation at the South Mine with apparatus and methods developed by the South African Committee.Through the Australian agent of the Cape Explosives Company, inquiries were made preliminary to procuring the necessary apparatus for the determination of dust, from South Africa. The writers then learned that the older gravimetric method used by the Phthisis Prevention Committee was likely to be superseded by the konimeter...

Jan 1, 1922

Process variables in flotation circuits are outlined with a view to producing mathematical models of circuits. The nature of the kinetics of flotation are discussed and the effect of process variables on the kinetics considered. An approach for a possible model is briefly outlined.

Jan 1, 1971

By Longworth C. R

Competing requirements for land usage sometimes make the correct all- ocation difficult. The decision can be complicated by many factors such as local resident pressure, previous government decisions, economic pres- sures and the duration or permanency of the competing land usages. This problem often confronts the extractive industries with consequent delays in granting leases and some- times considerable local dissension. A proposal to extend the high grade silica sand quarry of the Wamberal Sand Company Pty. Limited is a microcosm of these competing requirements. The sand quarry is located on the New South Wales central coast. It is an open pit operation on a near beach deposit of silica sand suitable for flint glass manufacture.

Jan 1, 1976

By Dunn J, Nguyen G, Graham J

A pyritic gold concentrate from the Golden Mile, Kalgoorlie, was roasted over a range of temperatures in a pilot scale fluid bed reactor. The calcines were subsequently cyanide leached. Mineralogical studies of the con- centrate, calcines and leached residues were also undertaken. Calcines produced at 500'C gave the poorest gold extractions and high cyanide consumptions. Gold recoveries of approximately 90 per cent were obtained from calcines produced at 550-600'C but higher roasting tempera- tures resulted in an increase in the residual gold content of the leached calcine. There is some evidence of flash smelting of the pyrite at the higher roasting temperatures and encapsulation of gold particles. Mineralogical examination of the calcines shows that the mechanism of oxidation is temperature dependent. At 500'C pyrite is directly oxidized to hematite with a concentric layered texture which appears to inhibit lixiviant access to enclosed gold particles. At higher temperatures the conversion sequence pyrite-pyrrhotite-hematite produces a spongy calcine which al- lows easier penetration by the leaching medium.

Jan 1, 1991

By A van As

This paper serves to outline the circumstances and causes of the air-blast that occurred at Northparkes Mines in November 1999. It describes the design of the mine, the geotechnical issues surrounding cave propagation and the cave monitoring systems that were in place prior to the event. A short description of the air-blast that followed a sudden collapse is given. Details of the risk assessment process that evolved during the rectification process are provided with their subsequent modification to form the core of a major hazard monitoring process. The system is in line with the recommendations given by the Coroner resulting from the inquest into the deaths of the four people who lost their lives during the air-blast.

Jan 1, 2005

Since the introduction of the Neil George Five Point Safety System, to the underground sections of The Zinc Corporation, Limited and New Broken Hill Consolidated Limited mines in March, 1969, the Disabling Injury Frequency Rate has been halved and shows signs of contin- uing to fall. The total accident frequency rate has also fallen, although the decrease has not been as significant. Before the introduction of the Neil George Safety System, analyses of the direct causes of accidents showed that approx- imately 25 per cent were caused by "unsafe conditions", while 75 per cent were attribu- table to "unsafe acts". Within twelve months of introducing the system, these percentages had significantly changed to 7 per cent unsafe conditions and 93 per cent unsafe acts. Today, the figures are 3 per cent and 97 per cent respectively, and these figures clearly show that the main emphasis in the current programme must be directed towards making the operating men safety conscious. The effort must be focused on changing the minds of men.

Jan 1, 1975

By C Vejrazka, A Wyllie

A common problem faced by underground mining operations around the world is airborne dust sourced from production and auxiliary processes. In most underground mining methods, air is generally directed through a limited number of drives and is thus more effective at carrying dust away from operational areas quickly. In a block caving operation, there are a number of ways to set up ventilation systems. In its simplest form the air is entering the extraction level through access drives and then split over the number of extraction drives—based on the pressure differences—without being regulated. This is the case at Northparkes Mines. Larger operations and panel caves most often utilise designated ventilation levels and ventilation raises with some form of regulation to ensure adequate airflow to all work areas.Northparkes Mines utilise electric loaders as a productive means to transport ore to the run-of-mine (ROM) bin, which have the added advantage of allowing the mine to require less airflow through the extraction drives as dilution of exhaust gases is no longer required. Dust was controlled during the operational period of the previous two block caves by using water spray bars in each of the drawpoints, which were seen as the main source of dust. These drawpoint spray bars only wet the surface of muck piles and require a lot of water to achieve an effect on the overall air quality. The drawpoint sprays can be remotely operated from mine control, whenever a loader is sent to bog a particular drawpoint. A significant amount of airborne dust is also generated during loading as rilling of material occurs, with further dust being generated during tramming and dumping activities as only limited mixing of the water and ore occurs. The water sprays are ineffective at precipitating dust that has already become airborne.When built, the currently operational E48 cave was fitted with drawpoint water sprays. As the cave is in a different orebody with higher silica content, the water sprays were not able to keep airborne dust and thus silica quantities under control efficiently. It was therefore necessary to find more sustainable solutions. The problem was further intensified by the concurrent load-haul-dump (LHD) processes across multiple extraction drives and tipping points, as well as secondary breaking, using non-explosive blasting and development activities occurring nearby.This paper describes the practical approach taken at Northparkes Mines to reduce personal dust exposure on the E48 extraction level. As the extraction level is one of the main contributors to airborne dust at the mine, it is believed that much can be learnt by focusing improvement efforts initially on this part of the mining process and later applying the effective solutions in other parts of the mine.CITATION:Vejrazka, C and Wyllie, A, 2014. Reduction of airborne dust on the E48 extraction level at Northparkes mines, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 227–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

Over years of exploration the massive and tabular orebodies in the area to the South West of Western Areas Gold Mine had been assessed as containing about 50 million ounces of gold û a world class orebody. Planning initially was for a surface and subvertical shaft system to exploit this area but because of cost, a single lift shaft to an area which could be accessed ex Western Areas was planned to intersect the reef at 2760 metres. It was also planned to mine out the shaft pillar area long before the deep shafts would reach that position. This is not the normal practice in South African Gold Mines. The stoped out shaft pillar was backfilled to minimise movement in the shaft sites. The result of a competitive tender/adjudication process was that Cementation Mining û Skanska won and was awarded the R192 million contract to sink the Main and Ventilation Shafts on 15 June 1995. On 1 April 1999 Western Areas and Placer Dome SA formed a Joint Venture, which now owns and operates the mine on which the South Deep Shafts are situated. This situation prevails today.

Jan 1, 2002

By D W. Airey

Frictional rock bolts are widely used because of their low cost. However, they have a thin wall section that makes them prone to corrosion, and they cannot be relied on to provide long-term ground support. It is difficult to assess the capacity after the bolts have been installed as they can only be pulled out if this has been allowed for during insertion. The questions of how long can the rock bolts function effectively and the effectiveness of various surface coatings, which can have significant cost implications are, investigated in this study.A series of accelerated corrosion tests have been performed on frictional rock bolts. The rock bolts, typically 900 mm long, have been inserted into concrete cylinders produced using a styrofoam insert to create the hole for the bolt insertion. Strata rock bolts with four surface coatings have been tested: uncoated black steel, galvanised, enduro (plastic coated) and coated with a proprietary aluminium/zinc alloy. Tests have been performed on two diameters of bolts. Following insertion of the bolts, the concrete cylinders were placed in a large drum filled with saltwater and current was applied to accelerate the corrosion process. The rock bolts were then extracted at various times after the commencement of corrosion. Comparison of the insertion and extraction resistances shows that corrosion initially increases the bolt resistance and that substantial section loss is required for the bolt resistance to drop significantly.CITATION:Airey, D W, 2014. Laboratory corrosion tests of frictional rock bolts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Tominaga Y

Mine ventilation control is one of the most important techniques to suppress the disastrous region within a limited area, to have enough time of emergencies (ignitions, fires and so on) for underground workers. The purpose of this paper is to introduce the simultaneous controlling of mine ventilation by using, micro computer connected to various kinds of sensors. In this study, basic of mine ventilation and graph theory are used for making computer programs when the characteristic curves of fans and temperature distribution in an underground roadway network are given.

Jan 1, 1981

By Morley I. W

In the year 1926, Edie Creek, in the Morobe District of the Mandated Territory of New Guinea, saw the greatest gold rush of recent years. Situated 35 miles inland from the coast, and at an altitude of over 6000 feet, Edie Creek presented to the original prospectors a wet, jungle-clad uninhabited, and inhospitable region. There were no roads; and the only means of approach from the equally inhospitable coast was by an eight to ten days' tramp through coastal swamps and gorge-scarred mountains. All food supplies and equipment had to be carried on the backs of "kanakas," and in many cases through country occupied by hostile natives.Since the first discovery of payable gold at Edie Creek, mining on the Morobe Goldfield has shown remarkable progress, and in spite of the tremendous natural difficulties, the field today ranks as one of the most important in Australasia.Aeroplanes, more than any other factor, have been responsible for this rapid development. They provide the only means of transport from the coast, and at present serve the needs of over 600 Europeans and 3000 indentured native labourers engaged in the industry.

Jan 1, 1933

By Shu DM, Moxon P

Subsidence profiles over longwalls at West Cliff Colliery (WCC) are predicted by three methods, NCB Emperical Method, Salustowicz's Profile Functions and Superposition of Two Critical Profiles. A method of deriving maximum subsidence using local data is also presented. For the first four longwalls, the results are compared with those from the subsidence surveys conducted during and after the extraction of each longwall. Longwall V has not yet been extracted, so the results are for the predicted subsidence profile. Superposition of two critical profiles is carried out in an attempt to check the principle of superposition. In addition, strata movement above the extracted longwalls is discussed.

Jan 1, 1986

The Abra mineralized body is regarded as a significant new style of mineralization for its environment. It is a blind polymetallic deposit, located in the Bangemall Basin of Western Australia. It was discovered by Geopeko in 1981 by diamond drilling a coincident magnetic gravity target, which revealed a large low grade epithermal Fe-Ba-Pb-Ag-Cu-(AuW) deposit, hosted by chemogenic and clastic sedimentary rocks, overlain by 200-500 m of clastic sedimentary rocks, of Middle Proterozoic age. The mineralization occurs as an upper stratabound phase, and a lower vein "stringer" style phase within a pervasive chlorite alteration envelope.

Jan 1, 1987