Search Documents

By C Muñoz, N Ortega, J Vergara, D Avilés

Mass blasts have been the subject of extensive studies because of their potential benefits in mining operations. However, it has not been possible to advance due to the paradigm that states that the blasts near the designed final wall or to critical structures have to be low tonnage. Another reason is the absence of specialised simulation programs to more precisely determine the influence of the energy released by blasting to the rock mass. There are some studies that demonstrate the possibility of massive blasting that maintain the design of the final slope (Farias and Santander, 2014). It should be noted that these studies develop the concept that the size of the blast should not increase the peak vibration in the rock mass.The study was carried out in partnership with Los Colorados Mining Company. Analysis, reconciliation and wall control for two types of blasts were performed:blasting production: approximately 850 000 t, with special wall control considerationsblasting of approximately 950 000 t over the entire width of the bench.Monitoring systems were used in the near field and far field using examination of holes in order to obtain information to assess the impact on the rock mass and then to compare these to conventional blasting combining production and contour blasting.The results show that for a large blasted volume, production and/or those generated from toe to crest on the bench did not produce more impact in the rock mass than the conventional blasting.The conclusions drawn from this study are:an improvement in the excavation rate of 7500 t/h that is higher than the maximum rates normally obtainedthe peak vibrations of the P wave generated by both blasts did not exceed the peak particle velocity criteria (Vergara and Muñoz, 2014)holes examination indicating no difference in their entire length, in pre- and post-blast reviewover US$2 000 000 savings generated in the year (estimated by the client) (Avilés, 2014).CITATION:Vergara, J, Muñoz, C, Ortega, N and Avilés, D, 2015. Benefits related to applications of a mass blast in open cut mining, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 625–632 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M Runkel, J Hammerschmidt, A Holmstr÷m, A Charitos, J Gnntner

"Roasting of sulfide concentrates and refractory ores is an important process step in the production of metals and chemicals. Sulfides of iron, zinc, copper and other metals are oxidised with air between 600 and 1000¦C into metal oxides or sulfates and gaseous sulfur dioxide. Roasting of gold concentrates and ores is a typical processing step used to produce a porous calcine suitable for cyanide leaching. During roasting, elements posing problems are removed through: oxidation (carbon, sulfur, arsenic and antimony) or volatilisation (mercury, chlorides and tellurides, as well as arsenic and antimony).This paper focuses on the environmental aspect of roasting using fluidised bed technology. The approach is to show that roasting is an attractive solution for refractory ore pretreatment since, on the one hand, it is an efficient technique yielding high gold recovery rates, while on the other it is able to comply with current stringent international environmental regulations. In that respect, roasting is compared to alternative processes, ie pressure oxidation (POX), bio-oxidation (BIOX) and ultra-fine grinding (UFG). Roaster high gold recovery rates are ensured through roasting-leaching test work, which allows the derivation of respective roasting parameters that are easily achieved in an industrial plant. On the other hand, key elements of the roasting process are analysed, which make it an efficient and sustainable technology, ie the possibility for energy recovery, the removal of off-gas impurities during the different gas cleaning steps (handling of arsenic, mercury emissions and further hazardous dust and gas emissions) and the treatment of the SO2-gas in order to produce sulfuric acid, and finally the treatment of the effluent produced. The processÆs environmental aspects are summarised by listing roasting emission values that comply with international regulations.CITATION:Charitos, A, Runkel, M, Gnntner, J, Holmstr÷m, A and Hammerschmidt, J, 2013. Roasting - a study on environmental aspects, off-gas, effluents and residue treatment, in Proceedings World Gold 2013, pp 509-518 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 26, 2013

By D Brereton, C J. Moran

In this era of rising focus on the social and environmental costs and benefits of mining operations, the valuation methodologies used to assess such impacts become increasingly important. Within an industry dominated by an engineering culture that places emphasis on net present value (NPV) calculations using high discount rates, difficulties often arise when attempting to justify projects with longer-term, harder to quantify benefits. This is particularly so when these benefits fall in the social and environmental domains and involve other stakeholders. In this paper, we summarise the results of a recent literature review on this subject, which focused on the valuation of æBeyond ComplianceÆ initiatives in the mining sector. We discuss a range of approaches including the quantification of hidden internal costs, financial methods of incorporating risk into calculations, the integration of quantitative and qualitative information, and also the valuation of æexternalitiesÆ or costs and benefits borne by others. We then use a series of examples relating to the management of water in the minerals industry to illustrate how some of these approaches could be applied. There are high-level commitments from both individual companies and groups such as the ICMM to incorporate sustainable development criteria into decision-making processes within the industry. We conclude the paper by arguing that, to meet these commitments, there is a need for the industry to adopt a broader range of valuation methodologies than appears to be the case at present.

Jan 1, 2006

By S Watson, L Martinez

Mine projects are complex opportunities that demand a constant assessment of uncertainty, ie risk and upside potential. This is because the value of a mine project is typically influenced by many underlying economic and physical uncertainties, such as metal/mineral prices, metal/mineral grades, costs, schedules, quantities, and environmental issues, amongst others, which are not known with much certainty at the beginning of the project. But, is uncertainty an enemy or an ally of the mine planner/analyst? To answer this question, this paper first assesses and elaborates upon the general concept of uncertainty. It then looks at the different sources of uncertainty in a mining project, such as the orebody, costs and product price uncertainties, and their effect on the final project value. Next, a general?review?of current mine evaluation techniques highlighting their limitations when dealing with uncertainty is made. Finally, an extended evaluation and risk management framework that addresses the existing uncertainty in the (greenfield/brownfield) mine evaluation process is proposed. One important characteristic of this framework is that it uses and manages uncertainty in order to generate additional value to the project; this is done through operational and managerial flexibility, which allow mine planners to minimise/maximise project risk/upside-potential giving a more realistic estimate of the projectÆs market value - this is shown in practical and simple examples occurring at different stages of a mine project, such as exploration and operation. Final conclusions are provided at the end.CITATION:Martinez, L and Watson, S, 2012. Uncertainty - An important source of (additional) value for mine projects, in Proceedings Project Evaluation 2012 , pp 131-140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By W L. Daniels, C Stilson, C Zimmerman

Mineral sands mining for ilmenite, rutile and zircon has disturbed over 1000 ha of prime farmland in Virginia (USA) since 1997 and additional areas are likely to be disturbed in Virginia and North Carolina (USA) over the next 15 years. Full-scale mining operations at the Old Hickory Project in Virginia were initiated in 1997 by Iluka Resources Inc. and restoration protocols have continued to evolve in response to a variety of economic, technical and social issues. Early on, the return of these lands to agricultural row-crop production was complicated by vertical stratification of tails + slimes and lateral variability in soil physical conditions in the reclaimed pits and by limited topsoil return. Virginia Tech and Iluka have worked cooperatively with all stakeholders for over 20 years to review the pre-existing research base, conduct new and innovative site-specific research and thereby provide reasonable expectations of post-mining soil productivity levels. In 2004, Virginia Tech, Iluka Resources and a local leaseholder (Carraway-Winn family) agreed to jointly manage a 45 ha research demonstration farm where the long-term effects of alternative soil reconstruction practices are being rigorously monitored for both row crops (corn and wheat) and forage production. All mined land crop yields are also compared to an adjacent undisturbed exceptional quality prime farmland soil. Row crop yields between 2005 and 2010 were significantly above county average yields (regulatory target level) and approximately 75 - 80 per cent of undisturbed adjacent prime farmlands. The state regulatory authority has recently relaxed its position on the necessity of topsoil return versus use of topsoil substitutes based on appropriate on-site research results and the ability of the reclaimed soils to meet comparative local county crop yield targets. This cooperative effort allows all clientele groups to objectively assess the post-mining productivity of these mined lands while providing an invaluable educational opportunity for the mining industry. CITATION:Daniels, W L, Stilson, C and Zimmerman, C, 2012. Development of effective rehabilitation protocols for mineral sands mining in Virginia, USA, in Proceedings Life-of-Mine 2012 , pp 97-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By M M. Collisson

The Synthetic Rutile (SR) plant operations, North Capel, produce electrostatic precipitator (ESP) fume and kiln scrubber residue. Typically ESP contains about 18 per cent Ti, 13 per cent Fe, 0.5 per cent Mn, eight per cent Si, six per cent Al, 16 per cent C, 0.9 per cent Zn, 0.6 per cent Pb, 300 ppm As, 300 ppm Cr and 5 ppm Cd. These wastes are held in a storage dam together with neutralised acid effluent (AE) liquor. A project was initiated to treat the fume and produce a benign residue that could be delivered to landfill, reducing dam space storage. Plant AE, containing free acid (9 - 14 g/L), Fe (6 - 7 g/L) and Mn (1 g/L), was used to leach ESP. The degree of extraction achieved for various elements include about 20 per cent Zn, almost 50 per cent As, five per cent Al, 0.4 per cent Pb and 15 per cent Cd. Extraction was most effective at pH The residue from AE leaching still contained Pb. TCLP tests of the leach residue produced Pb extraction significantly higher than the 0.1 ppm stipulated by Class 2 landfill guidelines. Other elements (eg As, Cd, Cr) successfully met the limits. Further leaching of the residue with EDTA extracted up to 65 per cent of Pb content. TCLP tests on treated residue showed Pb leaching potential of Lead was removed from the leach circuit as the sulphate by acidification of EDTA leach liquor, allowing EDTA to be recycled. The study showed that one waste stream can be used to treat another and help reduce plant waste.

Jan 1, 2001

The poor reconciliation between the values of estimated and actual grades can cause major economic losses to the mining industry. In a mining operation grade reconciliation is comparing the values of estimated grade calculated in exploration stage with actual grade obtained from blastholes' data. Many different factors affect the degree of reconciliation in a mining operation. In this paper we investigate the factors related to estimated grade which affects the reconciliation process in the exploration stage of the orebody. These factors are the sources of uncertainty in the rest of mine life. In this area the most important factors are inherent variability, statistical uncertainty and systematic uncertainty. A probabilistic model was presented to model each source of uncertainty. The implementation of proposed model was checked and its validity was investigated using real data in an iron open pit mine in Iran.

Dec 6, 2010

By A Nigam, K Biswas, R Sarkar

Because of the problems with 1st and 2nd generations of Advanced High-Strength Steels (AHSS), a 3rd generation of AHSS steels has become prominent and these steels have properties in between the 1st and 2nd generations of AHSS. However, although the 3rd generation of AHSS is a promising candidate as a replacement for its predecessors, there remain some challenges in processing these steels which are essentially medium Mn (Mn content ~ 5–7 wt per cent) and high Al (Al content ~ 1– 3 wt per cent) steels. The use of conventional casting powders based on the CaO-SiO2 system is unsuitable for high and medium Mn/Al steels. This work investigates the development of CaO-Al2O3- based mold fluxes for casting third-generation AHSS steel. Mold fluxes, with otherwise similar compositions but different C/A ratios, are tested and their crystallisation behaviour is examined using differential scanning calorimetry (DSC). A calcium aluminate phase having a composition Ca12Al14O33 was found to be the main crystalline phase in the mold fluxes. A decrease in crystallisation temperature was observed as the CaO/Al2O3 ratio increased from 1.00 to 1.33. The effective crystallisation rate constant exhibited an increase with decreasing crystallisation temperature, indicating a potential influence of nucleation rate on the overall crystallisation rate and suggesting an anti-Arrhenius behaviour in the crystallisation process of these mold fluxes.

Aug 21, 2024

By R Zhang, X Huang, M Zhou, X Lv, C Bai

Iron ore sinter accounts for a large proportion of blast furnace ferrous burden in Chinese steel mills. Depleting high-grade iron ore resources and spreading complexity of iron ores in mineralogy and morphology have made it more difficult to utilise iron ores efficiently and economically. In this paper, the physical properties of iron ore particles were characterised using mechanical sieving, laser sizing and gas adsorption. From those measurements, two physical indices (fractal dimension of the particle size distribution and surface morphological factor) are defined as important variables for optimising the granulation performance of iron ores. The moisture capacity and the contact angle of iron ore particles with water were also measured to determine the strategy of water-feed in the granulation process. It can be concluded from the experimental results that an increase in the fractal dimension of the iron ore particles will lead to a better granulation performance, while an increase in moisture capacity with a range of 12.8 ~ 14.8 per cent would increase the optimum water content where the granule packed bed achieves its best permeability. Furthermore, the optimum permeability varies inversely with the moisture capacity of the sinter mixture.CITATION:Huang, X, Lv, X, Zhang, R, Bai, C and Zhou, M, 2013. Iron ore characteristics and their application in optimising the granulation process, in Proceedings Iron Ore 2013 , pp 261-268 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By L W. Palmer

"Evaluating the geological risk associated with ore deposits is becoming common practice in the mining industry. While geostatistical simulation is a useful tool for evaluating this risk, the effect of applying different types of simulation is less understood. For simulation of categorical variables like rock types, available methods perform simulation in fundamentally different ways. In this study, the geological risk relevant for informed mine planning is studied with two categorical simulation methods, PluriGaussian Simulation (PGS) and Sequential Indicator Simulation (SIS). Risk is expressed as a probability of repeated occurrence of lithological units in the same location across simulations. Significant differences are observed between the methods in terms of spatial distribution of risk. To identify the most plausible risk model, the input parameters at every step of both techniques are scrutinised. PGS and SIS inputs are classified as four parameters that are: fundamental to implementation of the methodfixed to enable comparison of PGS and SISdetermined by user interpretation, hence variablenormally optimised during application of PGS and SIS. The effect of parameter selection from categories 1 and 4 on the risk model is investigated using drill core data from a leucogranite deposit. A corresponding block model is created for assigning outputs from PGS and SIS. Risk models produced by either method are illustrated in a cut-out from the block model to enable bench-by-bench comparison. For PGS, risk associated with relatively rare lithologies is relatively sensitive to variation of parameters. Independent of the abundance of lithology, a location-dependent effect of variogram and vertical proportion curve parameter selection is observed, with risk increasing towards the deposit edge. Although SIS requires fewer inputs, single lithologies must be modelled in turn. Using small numbers of samples in the search neighbourhood, all risk models differ substantially. For larger numbers of samples, the risk models are similar. Overall it appears that the risk model produced using SIS is less sensitive to changes than PGS but further work is required to confirm this.CITATION:Palmer, L W and Glass, H J, 2014. Risk associated with rock type prediction using simulation techniques, in Proceedings Ninth International Mining Geology Conference 2014 , pp 217–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

A variety of cement raw materials occur within the Cenozoic sequence in Northland. These form the basis of Golden Bay Cement's cement manufacturing operation at Portland, Whangarei. High grade limestone is taken from the Whangarei Limestone formation, which has been shown to have been sub-aerially weathered and developed mature karst features prior to deposition of the overlying allochthon sediments. In this instance, remobilisation of allochthon sediments following uplift and erosion is inferred. At Portland Quarry, argillaceous limestone is extracted from deformed thrust sheets in the allochthon sequence. Quarry operations have been designed to handle the steep asymmetric folds, thrust faults and fracture zones that affect the resource.

Jan 1, 1999

The Ranger Project Area covers 78.6sq km and is approximately six km east-west by 14km north-south (Fig. 1). The area is known to con- tain two uranium orebodies, Ranger No. 1 and No. 3, two uranium occurrences, Anomalies 4 and 5 and three significant radon anomalies, Ranger 18, 19 and 48. The Ranger No. 1 and No. 3 Orebodies con- tain approximately 120 000 tonnes of U308 in highly chloritised metasediments of the Lower Proterozoic Cahill Formation. The orebodies occur as suboutcrop and exhibit significant radiometric anomalies. These occur within approximately 400m vertically of the projected unconformity with the sandstone of the Middle Proterozoic Kombolgie Formation. Oxidised and reduced uranium minerals occur in quartz-rich schists containing variable muscovite, chlorite and sericite and in the chloritic matrix of chert breccia. Secondary uranium minerals namely saleeite, metatorbernite and gummite associated with earthy iron oxides occur from the surface to 50m depth in No. 1 Orebody and up to 80m depth in No. 3 Orebody. Below the oxidised zone, uranium occurs as pitchblende finely disseminated throughout sequences of quartz muscovite chlorite schist up to 150m thick and as open space fillings in zones of structural deformation. The uranium-bearing schists directly overlie up to 300m of dolomite and magnesite containing minor interbedded schist units and are themselves overlain by approximately 2 000m of more micaceous schists of the upper part of the Cahill Formation. Regional metamorphism has occurred to at least amphibolite facies and has been followed by retrograde metamorphism to a greenschist facies equivalent. The metasediments are intruded by granitic pegmatites and dolerites. Uranium is associated strongly with chlorite of which there are at least five textural varieties. Not all of the various generations of chlorite have associated uranium. Graphitic schist horizons occur which are often less than one metre thick and discontinuous. These are best developed at the base of the quartz chlorite schist sequence where uranium grades up to 1 000ppm U may extend for several hundred metres beyond the main ore zone. Uran- ium is not common in the carbonate sequences and only occurs in chlorite segregations in disrupted zones. The unoxidised ore contains sulphides, mostly pyrite, which are low in abundance (

Jan 1, 1984

By T Goldsmith

The mining industry is cyclical, but those are more than normal business cycles. In the early 2000s the industry saw the start of China as a game changer for the mining industry which lead to catch phrases like ‘stronger for longer’ and even ‘stronger forever’. Enter the global financial crises and the more recent slow-down in the Chinese economy and confidence that the future is bright has dimmed! This paper looks at the long-term forces that are likely to impact the global mining sector and explain why the industry has an excellent future. However, the industry is not without its many challenges and while demand may be in a prolonged step change, the ability to generate profits will depend on the fitness of each asset and company.The author also discusses the hated terms of ‘boom’ and ‘bust’ and considers how the industry can reduce them, but normally exacerbates them. The ability of the junior sector to raise funds being a primary example and one that remains closed to all but the very best exploration assets. There is also consideration of Australia’s position as a mining country in the future world.CITATION:Goldsmith, T, 2014. The future of the global mining sector, in Proceedings Ninth International Mining Geology Conference 2014 , pp 15–20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By T Y. Dube

In this paper current net present value (NPV) based mine valuation techniques that take into account market and private risk are discussed and analysed. Potential pitfalls that arise from the application of a portfolio, market or commodity based risk metric to a mining project are identified. An alternative non-simulative framework for quantifying and factoring market and private risk in NPV calculations is proposed and then applied to a hypothetical case study in an attempt to overcome identified pitfalls. Mathematical proof that a static discounted cash flow (DCF) calculation can underestimate or overestimate mine NPV is presented, the conditions for each are outlined and the degree of underestimation defined.CITATION:Dube, T Y, 2012. How the use of market-based risk metrics can undervalue good mining projects and overvalue poor ones, in Proceedings Project Evaluation 2012 , pp 29-34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By A R. Proudman, A H. Purvis

The Granites Gold Mine Callie gold deposit is located 550 km northwest of Alice Springs in the Tanami Desert. Gold mineralisation occurs due to a complex interplay of geological factors which include but are not limited to favourable lithology, structure, alteration and quartz veining. High-grade mineralisation, while pervasive under favourable conditions, is highly variable over short distances and is very nuggetty. In contrast, the lithology and geological structures that host the mineralisation are very continuous. Orebody modelling techniques have evolved over time because of a growing understanding of the mineralisation controls. Modelling issues such as sampling and assaying accuracy, modelling method, data density, gold population statistics, geological interpretation and domaining, grade boundary and calculation conditions, and model block size are constantly being reassessed in an effort to increase understanding of the mineralisation controls and modelling accuracy. The evolution of the modelling process in response to increasing data levels and a growing understanding of the mineralisation controls has resulted in changes to the perception of the orebody size and style. This has caused the choice of underground mining method to be revised several times and the process to final mining method selection to take longer than usual. In order to achieve the planned production start-up date of July 1998 the process has been allowed to progress in parallel with development of the underground mine. This paper describes the resource modelling and mining method selection process applied to the Callie underground mine and some of the issues which have contributed to its evolution. Some conclusions that are relevant to the efficient planning and development of new mining projects in general are presented.

Jan 1, 1998

By W N. Qin, B Zhang, W Z. Huang, X S Mo

Mengzi Mining and Metallurgy Co, Ltd (MMMC) polymetallic ore contains recoverable amounts of tin, lead, zinc, pyrite and other valuable minerals. With the change in orebody, the run-of-mine (ROM) ore changed from lead zinc rich ore to tin rich ore, where the current ROM ore contains 0.45–1.25 per cent tin, 20–25 per cent sulfur, and 0.20–0.35 per cent copper. The previous processing flow sheet was designed to recover lead zinc rich ore and it is clearly not suitable for recovery of the current tin rich ore, where the tin was already overground and tin recovery was only 50.19 per cent. The Mengzi Mining Company has recently modified the concentrator circuit by incorporating rod mill and high efficient Derrick fine screen. As a result of the improved classification efficiency, the overgrinding of the tin ore was minimised and the recovery of tin was improved by 20.71 per cent, ie from 50.19–70.90 per cent. An additional $10 M revenue per annum can be achieved as a result of the modification.CITATION:Qin, W N, Huang, W Z, Mo, X S, Zhang, B and Wheeler, J, 2014. Application of high efficient fine screen to improve the recovery of tin concentrate, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 487–492 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M Noakes

EcoTechnology refers to a series of potential metallurgical processes for complex ores, concentrates, tailings and slags that are all based on an initial chlorination step at low to moderate temperatures probably in a fluid bed chlorinator (FBC). Examples of the research and development (R&D) results are provided in this paper for a high grade Au/Sb Leach Tailings (EcoGold<sub>®</sub> Process), a very refractory sulphide Au concentrate, a refractory gold calcine tailings, a Cu/Au tailings (EcoCopper<sub>®</sub> Process), bulk polymetallic sulphide concentrates and polymetallic sulphide/oxide complex ores (EcoZinc<sub>®</sub> Process and EcoLead<sub>®</sub> Process). R&D on over thirty different ore types has been conducted at a bench scale as discussed. Latterly a dedicated pilot plant was designed and constructed by EcoTech Mining Pty Ltd (EML) and several of the different feed stock results have been confirmed by pilot plant testing. It is planned to scale up to a commercial demonstration plant. To demonstrate the versatility of EcoTechnology, bench and pilot plant test results on five of the projects are used as case studies as follows: Fosterville ‘leach tailing’, VIC; Wiluna flotation concentrate – BIOX Feed, WA; Wiluna calcine facility tailings, WA; Mt Morgan Cu/Au tailings, QLD; Polymetallic sulphide concentrates from Pegmont Deposit, QLD and Polymetallic sulphide/oxide ores from Commonwealth Mine Project, NSW. CITATION: Noakes, M, 2018. Improved recoveries and environmental outcomes from complex ores utilising EcoTechnology, in Proceedings Complex Orebodies Conference 2018, pp 122–123 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

The Cadia Valley Operations currently hosts a large operational open pit, a large operational sublevel caving underground mine and two other underground projects at the study stage. This scenario creates an unusual situation for the evaluation and planning of a fifth major open pit project. The Cadia East Open Pit is a large gold-copper development located adjacent to the operational open pit and above one of the underground projects. A study team is conducting a comprehensive and robust analysis of the target orebody. Two key factors for this project include the existing and planned projects within the valley and the wide range of available mining methods. The aim for the study team is to present an optimal and practical case which suits the entire Cadia Valley Operation. A rigorous and robust analysis of the situation requires that each factor be properly evaluated. A modular system has been developed which allows the wide range of scenarios to be quickly and meaningfully considered. Sensitivities for each module drive the further development of that particular module. As each scenario progresses, an assessment is made evaluating its value, strategic value and practicality. In such a way, the number of scenarios is gradually reduced at each stage to produce a final short list of feasible cases. Each scenario on the shortlist is then assessed with regard to the existing operations and other projects. A qualitative and quantitative analysis is made. This ranking is used to provide the recommended case.

Jan 1, 2007

By A Scott, S Kanchibotla, J Segui

The æMine to MillÆ concept is not new. In fact, it is the underlying objective of every mine. Unfortunately, in many operations the management structure and reporting systems have created independent æbusinessesÆ within the overall mining enterprise. This has created incentives to optimise the performance of each component of the operation rather than the enterprise as a whole. The Mine to Mill Conference organised by The AusIMM in October 1998 documented a number of case studies where run of mine ore was not presented to the mill in the best possible form for subsequent stages of comminution and processing. A number of examples were quoted where modest expenditure in the mine had a very significant impact on downstream process efficiency and hence costs. Examples included:the minimisation of fines in the mining and handling of iron ore; the management of fines in blasting and crushing for a copper heap leach operation; the control of blast damage, mining recovery and dilution in open cut coal operations; and the optimisation of mine fragmentation to increase mill throughput in gold and copper operations. The latter topic has been trialed at a number of mines and is referred to as æMine to MillÆ fragmentation. A number of æMine to MillÆ type investigations have been reported in the literature including Pease et al, Simkus and Dance, Nielsen, Scott et al, Kojovic et al, Kanchibotla et al, Bulow et al and Hawkes from the 1998 Mine to Mill Conference. In addition, a number of studies are in progress or the results have yet to be published. These studies have demonstrated the feasibility of obtaining the data required to characterise the breakage behaviour of ores and to model the impact of changes to blasting practices on process efficiency. Characterising the breakage behaviour of ores is a vital step in the management of fragmentation and comminution in mines. The characteristics of importance to fragmentation fall outside the parameters conventionally required to describe the economic geology of a deposit. æMine to MillÆ optimisation of fragmentation means that the mining engineer needs information from the geologist in order to be able to help the metallurgist. Providing this information requires close interaction between these groups.

Jan 1, 2000

By D G. Rantucci

Organic carbon is a major ore contaminant at MMG’s Century mine. This carbonaceous matter is associated with shale hosted sphalerite mineralisation. It occurs as elongated lamellae and as inclusions in porous sphalerite aggregates which are fine grained and difficult to liberate from sphalerite. The carbon prefloat circuit was designed to remove the liberated organic carbon in order to mitigate excessive reagent consumption, contamination of the lead and zinc concentrates and poor flotation performance in the primary zinc circuit. The consequence of organic carbon removal is that sphalerite and galena minerals are lost to the prefloat concentrate. A Jameson Cell was installed in late 2005 as a prefloat cleaner cell. Operational experience showed that the cell became capacity limited during periods of high amounts of organic carbon in the feed and was subsequently bypassed.Reactive style operating strategies were implemented to manage the effects of insufficient organic carbon removal by the prefloat circuit but due to the relatively large circuit residence time, upstream changes meant hours before the downstream circuits were stabilised following a disturbance from excess carbon.This paper describes the modifications and testwork undertaken to enable the Jameson Cell to be operated during periods of high organic carbon in the float feed and the implementation of process control initiatives to proactively remove the required prefloat mass from the float feed to eliminate the reactive style operating strategy.The process control modifications centred on dynamically targeting a prefloat mass recovery determined by an equation relating the carbon to zinc ratio to the carbon prefloat mass as a percentage of the float feed. The equation was developed by analysing historical data. These improvements served to optimise the prefloat circuit and consequently stabilise the downstream lead and zinc circuits.

Aug 8, 2011