Search Documents

By Bellairs P, Stewart JC

On 20 December 1983 at 8.40am blast- hole 57 of Blast RN177 prematurely detonated follwed by a violent deflagration of blast- hole 59 at 10.40am. The blastholes were 380mm diameter drilled in black pyritic Mt McRae shale. The blastholes were loaded with ANFO and primed. Blasthole 57 was stemmed and blasthole 59 was not. A poss- ible mechanism which could lead to such a detonation is described. preliminary tests showed the top 5m of a bench had the highest temperature which could not be influenced by a range of treat -ments. Small scale laboratory tests show- ed that zinc oxide (ZnO) and magnesium carbonate (Mg2CO3) inhibited the reaction. A series of tests using AN with and without inhibitors loaded into the collars of blast -holes drilled in the top 6m of the bench and unstemmed is described. An analysis of the time to reaction of the holes loaded with AN against temperature shows that the decomposition of the AN in contact with the black pyritic shale is probably a sulphuric acid catalysed react- ion. All the inhibitors tested can neut- ralise the sulphuric acid in the shale. 10% ZnO appears to be an effective inhibitor of the reaction providing the AN/ZnO (90/10) is kept out of contact with surface material whose temperature can be as high as 60¦C in summer. It is concluded that ANFO/ZnO (90/ 10) should be now tested in stemmed holes.

Jan 1, 1986

By W R. Adamson

Cerro Vanguardia SA (CVSA), property of AngloGold Ashanti, mines gold and silver from a system of vetiforme orebodies located in the south of the Argentine Patagonia, in the Province of Santa Cruz.Surface mining techniques are applied to develop a series of narrow pits with an average waste to ore ratio of 26:1. This quite unique constraint brings into focus the need to maximise inter-ramp and final wall angles, leading to a strong need to optimise wall control drilling and blasting in order to reduce back-break damage to an absolute minimum.The paper describes a program of applied investigation and design modification implemented during?2008?and?2009 in?two?separate pits of Cerro Vanguardia. Three distinct yet complementary damage mechanisms were identified and observed during the field components of the work; vibration induced strain fracturing, surface cratering around blasthole collars and quasi-static loading and unloading of the surrounding rock mass as a consequence of poorly controlled confinement.With these mechanisms identified, a measurement, modelling and modification campaign was conducted in order to reduce the incidence of each source of damage. Interactive design analysis and modelling, near-field vibration measurement, video capture and the application of electronic initiation technology were supported by seed wave modelling and topographic evaluation of the achieved results.Results point to the usefulness of simulation techniques for determining optimum delay timing to reduce vibration impact, while the visualisation of explosive energy distribution produced by drilling and explosive loading decisions assists in reducing the probability of over-confinement.This paper presents relevant aspects of the two fieldwork campaigns:1) describing the application of the techniques, and2) summarising the results obtained.

Nov 8, 2011

By G S. B Karunatillake

Following a pre-feasibility study, Mount Isa Mines commenced a feasibility study on the deposit of the George Fisher Mine in May 1997. Board approval was granted in May 1998 to construct a 2.5 million tonne per annum mine and to upgrade existing concentrator and smelter facilities. The world-class George Fisher zinc-lead-silver deposit is located approximately 22 kilometres north of the city of Mount Isa, in north-west Queensland and is 2.6 kilometres north of the existing Hilton Mine. It will be a large-scale underground mine, sustaining a profitable zinc-lead-silver business in Mount Isa for at least ten years. This paper will outline the details of the mine that was developed during the feasibility and design phase. It will include a description of the mining methods, ventilation, fill, ore handling, services and infrastructure. The utilisation of existing assets and the development of innovative ideas were essential to the successful economic development of the George Fisher Mine.

Jan 1, 2000

By P B. Hills

A simple algebraic method of aligning large scale underground excavations such as a crusher station or workshop or indeed any large cavern or mine layout to the optimal stress condition is outlined. The method uses the stress transformation law to determine how the component stresses vary as the stress tensor is rotated around its axis. The aim is to define the orientations at which the maximum and minimum horizontal stresses occur such that the excavation can be aligned with its long axis paralleling the trend of the maximum horizontal stress leading to the minimum potential for overstressing of the side walls. The physical environment in which the stress field is acting is unchanged. At the design location, the trend and plunge of the major principal stress is unchanged. However, the coordinate system by which the location of the stress field is described is arbitrary and the stress transformation law allows that coordinate system to be rotated to a more convenient orientation and for the component stresses to be calculated within the alterative coordinate system. The stress field is typically described in terms of normal and shear stresses aligned to a north–south, east–west, vertical, coordinate system. In this scenario, there are two orientations in the 360° horizontal plane defined by the coordinate system where the horizontal normal stresses are equal, and at 45° to those orientations, two orientations where they diverge to the maximum extent. Those orientations of maximum divergence correspond to the trend of the maximum and minimum horizontal stresses, usually designated σH and σh, and that is what the algebraic manipulation seeks to determine. This technique is a first pass assessment which relies on a knowledge of the full stress tensor. It is not a replacement for numerical modelling or detailed design, but a tool to guide planning.

Nov 29, 2022

By A Bird

Gravity gold circuits have an important part in reducing operating costs and maximising recovery in modern gold plants where coarse gold is present in the ore body. The design and selection of equipment has a vital part in the overall effectiveness of the gravity gold circuit. There are a number of associated factors that need to be taken into consideration when selecting the most suitable equipment for gravity gold circuits including occupational health and safety, security and labour requirements. This paper is a case study that outlines the validation behind the design, selection of equipment and subsequent benefits of the recent upgrade of the gravity circuit at the Marvel Loch gold mine with the main component to the upgrade being the installation of a Consep Acacia Reactor. Since the upgrade there has been a significant increase in gravity recovery, which has reduced the amount of gold reporting to the leaching circuit therefore reducing reagent consumption and overall operating costs. There has been an increase in overall gold recovery and therefore increased gold production. The benefits to occupational health and safety include the removal of toxic gases being released in the gold room during the previous practice of gold concentrate calcination and the removal of the arsenic and nickel from the gold doré, which poses a risk during refining. Manual handling and security has improved as there is no physical contact with gold concentrates during the automated process using the Acacia reactor. The total time for gold room personnel working in the gold room has also reduced from around six hours per day to less than one hour per day.With the continuing development of low grade gold deposits, there will be an increase in demand for low capital, high recovery gravity gold circuits that can significantly increase overall production while reducing operating costs.

Aug 8, 2011

By Lyman G. J

Magnetic separator operation in the recovery of magnetite in heavy medium circuits was studied by conducting a series of tests on a full size wet drum magnetic separator.The significant operational variables were found to be feed pan clearance, squeeze pan clearance, dry magnetite feed rate and separator drum speed. With feed and squeeze pan clearances optimized for typical primary separator operation, magnetite loss and concentrate specific gravity were found to be related in a regular manner to dry magnetite feed rate at any drum speed.A two component model of magnetite loss is proposed, relating total magnetite loss to losses in the feed pan and squeeze pan zones. The experimental curves relating magnetite loss to dry magnetite feed rate at the various drum speeds are interpreted in terms of the two component model.The magnetite particle size distribution in the separator was also examined. The tailings magnetite was found to be finer than the feed magnetite only when the dry magnetite feed rate was low, or immediately following the introduction of a new charge of magnetite when the separator was fed at an intermediate dry magnetite feed rate.

Jan 1, 1983

By S Grobler, T Fares

Understanding the real utilisation of the available volumetric capacity of a conveyor is key to unlocking latent capacity or ‘debottlenecking’ existing plant. Conveyors are typically designed on the basis of conservative density and ore surcharge angle specifications, and consequently there is often latent volumetric capacity available.Laser scanning measurements of conveyor ore profiles has been undertaken on iron ore conveyors to gain an understanding of the actual surcharge angle and the available edge clearances. Iron ore producers seeking to extract maximum production from their assets have used these measurements to debottleneck existing plant and to revise the design criteria for future plant. The benefit is that latent capacity of existing plant can be unlocked and smaller and cheaper conveyors can be designed for future plant, maximising the return on capital. This paper describes the measurements and results.CITATION:Fares, T and Grobler, S, 2015. Laser scanning of conveyor ore profiles, in Proceedings Iron Ore 2015, pp 549–554 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By C D. Rose

A review and summary of the results of 120 coal sampling system bias tests is presented. This review supports new methodology using multivariate statistics currently being considered by ISO TC27 SC4. The current difficulties with ISO 13909-8 are explained and the logic behind the current new working draft is discussed in detail. Bias was detected in nearly 36 per cent of tests reviewed, suggesting that much improvement is needed in designing, maintaining and monitoring the performance of sampling systems in order to avoid sampling bias.CITATION:Rose, C D, 2012. Bias testing of mechanical sampling systems for coal - A review of test results and call for use of multivariate statistical analyses, in Proceedings Sampling 2012 , pp 185-192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By H Kurth

Geoscan is used for multi-elemental analysis of conveyed bulk materials in real time. It has been used for coal analysis since the 1990s, in the cement industry, and since 2003 for measuring mineral ore quality. Geoscan-M has proven performance and demonstrated paybacks of weeks or months, in iron ore, manganese, copper, zinc-lead and phosphate industries. Geoscan-M measures continuously through the full bed depth and is unaffected by belt speed, particle size, layering and dust levels. Increments of two minutes (typically one to five minutes) are accurately measured and provide the plant operators with tonnage weighted results of each element within seconds.A Geoscan installed after crushing is able to measure quality shortly after mining. The analysis results can be used to divert the increments based on composition, such as diverting waste for disposal and diverting marginal material to a stockpile for processing at a later date. The bulk sorting process allows different qualities to be placed into relevant stockpiles for subsequent blending. Material meeting product DSO (Direct Shipping Ore) quality can bypass a beneficiation circuit to prevent unnecessary treatment costs. An analyser in a blending application enables proportioning of different quality feed materials from multiple stockpiles to achieve a desired compositional consistency for process feed. The parameter used for decisions may be; a) primary metal content, e.g. Cu, Fe, P, etc. b) deleterious component content, e.g. Mg as an indicator of talc content, c) process parameter content, or a combination of these. Process parameter content may be the elemental ratio between critical components, e.g. Cu:S ratio, Fe:Si ratio, basicity, Lime Saturation Factor, etc. or the content of an “indicator” element, e.g. Si as an indicator of material hardness or grindability.Measurement of the composition in real time enables prompt feedback to the mining operators and also feed forward to the process operators. Compositional variability can be critical in the process and advance warning enables appropriate reactions prior to processing. This may include modifying the feed rate, changing the feed blend (through additives), or modifying reagent dosing in anticipation of a change in feed quality. Benefits include, but are not limited to; reducing waste processing, improved feed grade stability, reducing energy, water and grinding media consumption, producing less tailings, increasing process efficiency, higher metal recovery, better plant utilisation, reducing plant downtime, better utilising mined material, all achieved using the same process plant throughput capacity.CITATION:Kurth, H, 2015. Optimising plant feed quality and process performance using Geoscan elemental analysis, in Proceedings MetPlant 2015, pp 373–380 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Prior to 1972, Peko Mines Limited at Tennant Creek used a central mill at Peko, which consisted of a gravity circuit, flotation and cyanidation of tailings, to treat their gold ore from surrounding mines. The Warrego concentrator, 60km to the west, was built to handle the Warrego and Gecko copper orebodies, which were being developed concurrently with the concentrator construction The Warrego concentrator consisted of a flotation circuit, using autogenous grinding at 100 - 120 tph, compared to the more elaborate Peko circuit employing rod mill - ball mill grinding capable of treating only 18 - 26 tph. During development of the Warrego copper mine a gold rich ore pod was located, because of which the mining plans were adjusted to allow simultaneous, separate extraction of the copper and gold ores. However, the plans for the concentrator were not affected as the gold ore could be carted 60km to the Peko central mill for processing.

Jan 1, 1978

BHP Billiton Olympic Dam produces copper cathode, uranium oxide concentrate and refined gold and silver. The operation is comprised of an underground Mine and Processing Plant and is located 560 km north of Adelaide. Water for the operation is sourced from two wellfields located 120 and 200 km from the operation in the Great Artesian Basin (GAB) at a rate of approximately 36 ML/d. Regulatory drawdown limits were established to protect regional GAB springs and are monitored at compliance bores. Drawdown was predicted in the æOlympic Dam Environmental Impact StudyÆ (Kinhill, 1997); however, pumping at higher volumes may have the potential for increased drawdown resulting in a trend towards the compliance limits. In recent years increased usage of water in the Concentrator and Hydromet sections of the Processing Plant has caused excess process water reporting to the Tailings Retention System (TRS). This has resulted in excessive amounts of liquor ponding on the tailings cells with a potential impact being contamination due to seepage of liquor to groundwater. Effective management of water by the operation is necessary to both reduce GAB drawdown and reduce the amount of liquor on the tailings cells. A site working-group has been established to investigate and pursue opportunities to improve the water use efficiency of the operation. This paper will highlight the issue of water management at Olympic Dam and discuss the various options currently being investigated to improve management of this important resource.

Jan 1, 2006

By D Bruce, D Cox

The main access decline at Carrapateena mine was excavated through two different underground aquifers. In these areas of decline, pressurised water finds the path of least resistance through the rock and into the excavation. In some locations the ground water would upwell underneath the roadway resulting in rapid deterioration of the running surface. The deterioration of the road was so rapid that the two areas of decline required significant roadworks every single shift or it would become impassable by mine traffic. With a full fleet of underground trucks hauling to the surface, managing these sections of roadway was impractical and unproductive. The site team resolved this issue by installing Roller Compacted Concrete (RCC) to the affected sections of decline. RCC is a specialist concrete product that is delivered to the site near dry and is installed using a grader and roller similar to road base. This product can be installed quickly and be trafficked within hours of installation, making it ideal for mines with single access declines and unfavourable road conditions. RCC roadways were successfully installed at Carrapateena mine in conjunction with under-road drainage. These roadways have proved to be a very effective solution which requires minimal maintenance and are resistant to water ingress from the aquifer. This paper discusses the technical aspects of the RCC, as well as the practical implementation of the solution as a whole.

Mar 15, 2021

By G R. Power

A useful way to assess potential productivity of SLC mines is by quantifying tonnes/drawpoint/day to be extracted from the mine. However limited industry information has been published to help mines benchmark this number. This paper assesses industry data which can be used to support estimates of potential productivity from new mines based on tonnes/drawpoint/day. The information used has been extracted from historical production schedules which indicate what was achieved, rather than what was planned. It has been assessed using an algorithm created for the purpose and is presented with discussion of varying definitions of active drawpoints, analysis of the data and inquiry into some of the underlying contributing factors.

Mar 15, 2021

Using DEM to Model Industrial Banana Screens

Sep 13, 2010

By J Planner

As Australia’s coal and iron ore export volumes increase to meet international market growth, port terminals, mining operations and rail transport systems can be the source of increased dust emission. Current and future sustainable expansion must minimise dust emission from bulk handling and transport operations located in close proximity to residential areas. Lower level dust emissions can be controlled by operational measures such as water addition to products, and use of water spray on stockpile surfaces. Recent research has shown that higher levels of dust emission can be more effectively controlled by understanding and treating the dust characteristics of each individual bulk product. Application of this research, progressively being applied at Australia’s coal and iron ore port terminals and rail transport systems, is achieving compliance with health standards and minimising dust nuisance effects to an acceptable level.

Nov 22, 2011

Open pit mining has considerable damaging effects on the environment of the mining region. These harmful influences have to be controlled during mining operation until mine closure. Different sections of mined land, such as; pit(s), waste dump(s), tailing pond(s), roads, areas for onsite facilities and free land zones which are not mined, have to be reclaimed through treatment of environmental pollution and implementation of a permanent post mining land use (PMLU) after mine closure. Implementation of a permanent optimal post mining land use (OPMLU) is one the most decisive criterion which effects on reclamation procedure, mine closure and their costs. Therefore to define ultimate pit limit (UPL), mine closure and reclamation costs should be entered in the calculation iterations same as the other variable costs of the projects. Estimation of closure and reclamation costs of a mining project is carried out based on the attained OPMLU and the specifications of the mine site. In this paper, a model is developed to provide OPMLU for pit area through fuzzy multi-attribute decision making (FMADM) technique. The model was implemented on a hypothetical copper mine in northwest of Iran as a case study. Lumber production was selected as OPMLU for the pit area. It is finally concluded that through the developed model, OPMLU for different sections of mined land in an open pit mine project is defined. Also closure and reclamation costs are estimated based on the defined OPMLU to achieve a more accurate UPL.

Dec 6, 2010

By T Honeyands, L Jelenich

We are currently witnessing large fluctuations in the relative price of ironmaking raw materials brought on by changes in the dynamics of supply and demand, market conditions, environmental regulations and technical factors affecting the iron and steelmaking process. From a customer perspective, it is the behaviour of iron ores in downstream processing that give them their value; their impact on the sintering or pelletising process and subsequently blast furnace ironmaking. It is therefore important to consider this value when developing projects, making mine planning/cut-off grade decisions and in setting price differentials for differing quality.This paper describes the use of the Marx value-in-use model to quantify the downstream value of lump iron ores. The Marx model consists of heat and mass balance modules for sintering and pelletising and a rigorous two-stage heat and mass balance model of blast furnace ironmaking. Mass balance and cost models are applied for steelmaking, casting and rolling. The use of a heat and mass balance allows accurate comparison of the impact of raw material properties on blast furnace operation. The impact of minor elements, such as alumina, silica and phosphorus, and metallurgical properties on ironmaking is described, and examples are given for the calculation of a lump premium.CITATION:Honeyands, T and Jelenich, L, 2015. Lump ore properties and their impact on value-in-use in ironmaking, in Proceedings Iron Ore 2015, pp 359–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Open pit mining at Bingham Canyon commenced in 1904 and about two billion tonnes of ore have been extracted since then. There remain just under one billion tonnes of ore in the pit and this will be mined by 2015. Because the porphyry system extends below the ultimate pit limits, Kennecott Utah Copper Corporation initiated a study in 1997 to determine the viability of underground mining. The study was initiated at that time because the results were to be used to compare the economics of a further pit expansion to that of an underground mine. If a pit expansion was viable then overburden removal would have to start in the near future. This paper is a summary of the work that was carried out for the underground study. Block cave mining was determined to be the most appropriate method to mine the deposit. Two block cave areas have been planned with a total production rate of 72 500 tpd. Additional sources of ore will come from skarn orebodies that are associated with the porphyry deposit. The geology of the deposits is described together with the geotechnical techniques that were used to characterise the rock in the absence of more detailed data that are normally available. A general description of the mine plan is given along with the reasons for selecting the particular methodology used. The study was completed at the end of 1998 and demonstrated the viability of underground mining at Bingham Canyon. Funds have been approved for further drilling and technical studies, which will lead up to a feasibility study in 2004/5.

Jan 1, 2000

By C J. Unger, T Baumgartl, C J. Bond, P Sabourenkov, V C. Glenn

Social licence to mine is influenced by society’s perception of the mining sector’s ability to effectively rehabilitate mined land and for governments to appropriately regulate that process for the broader community benefit. In Queensland, Australia, many mine rehabilitation personnel working for active coalmines, as either staff, consultants or contractors, belong to the Central Queensland Mine Rehabilitation Group (CQMRG). The CQMRG was established 23 years ago with the aim of sharing informal knowledge related to practical aspects of rehabilitation in order to leave as positive a legacy as possible from mined land. This voluntary group of professionals also includes members from regulatory agencies and civil society. Within the dynamic regional mining environment, mine rehabilitation professionals benefit from sharing their informal knowledge.CQMRG is currently a group in transition. Mining boom and downturn cycles have exacerbated the loss of accumulated knowledge in the core CQMRG membership due to rapid changes in personnel at mines in the region. Additionally, some of the most experienced CQMRG-affiliated rehabilitation practitioners are approaching the end of their careers and want their valuable and less formal knowledge retained. This paper discusses the development of a research project that emerged in response to the anticipated loss of several decades’ worth of valuable knowledge as rehabilitation practitioners in CQMRG left the region or the workforce.CITATION:Unger, C J, Bond, C J, Baumgartl, T, Glenn, V C and Sabourenkov, P, 2016. ‘MRC-wiki’ – a mine rehabilitation and closure knowledge management tool for Central Queensland coalmine practitioners, in Proceedings Life-of-Mine 2016 Conference , pp 39–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By L Chaffey, M Buckland

The minerals industry has enormous potential to positively contribute to sustainable development and many leading companies have concluded that their long-term success is directly linked to their ability to leave a lasting positive legacy. While there are many examples of success, there have been failures as well and much work has been done in recent years to define the role of the minerals industry in sustainable development and identify the key elements for success. In the past, our sector could point to the taxes and royalties it paid, the exports it generated and employment it created and felt confident that its contribution would be recognised and duly acknowledged. This is no longer the case. Critics of the industry have highlighted resource-rich countries that have failed to capitalise on their resource wealth and have arguably lower standards of living than their resource-poor peers û the æresource curseÆ hypothesis. Recent research has done much to clarify the factors that contribute to a countryÆs success or failure and all stakeholders in the industry now need to include these learnings in their approaches going forward. We know that our long-term success relies on embedding a company- wide approach to sustainable development into all aspects of our business operations. In this paper we highlight BHP BillitonÆs experience in the development and implementation of policies and systems designed to enhance our contribution to sustainable development. We detail the business drivers for excellence in this area and the key external codes and initiatives that have shaped our approach. The values-based BHP Billiton Charter, Sustainable Development Policy and associated Health, Safety, Environment and Community (HSEC) Management Standards are central to our approach. Implementation is reviewed through our HSEC audit program. One area in which we have placed particular emphasis is our approach to community development. BHP Billiton has a corporate target to contribute one per cent of its pre-tax profit on a three year rolling average to voluntary community programs. As our profit stream has increased with the minerals boom this is approaching an A$100 million commitment. In our paper we detail how we are working to ensure we maximise the value of this contribution for our communities and our shareholders.

Jan 1, 2006