Search Documents

The discussion which followed the publication of my paper by the formert has, I think, enhanced its value. It may therefore be of interest to members of our Australasian Institute, who are not members of the Institution of Mining and Metallurgy, if I give a synopsis of the discussion.My attention was drawn to the fact that my paper did not make clear the extent of the improvement in furnace operations, which followed the use of coke of high quality; this comment applied more particularly to the lead content of slag. My failure to supply comparative figures in regard to the lead content of slag was governed by a condition which, I think, is of interest to metallurgists. As a result of industrial...

Jan 1, 1932

By Madgwick J. C

Microaerobic biodegradation oflow-grade manganese dioxide slurry tailings was demonstrated in enrichment cultures treated with dilute molasses at 30°C and pH 5·8. Supplementary nitrogenous nutrients, yeast extract addition and pH adjustment were not required.Continuously stirred, air-limited reactors were superior to still intermittently agitated cultures, in that, at 5 per cent (w/v) MnOz tailings and 5 per cent (w/v) molasses, the yield of 0.12 g Mn++/g molasses, the rate ofleaching of 1·06 g Mn++/l/d and a recovery of Mn++ of 58 percent from MnOz were 2·8 times, 1·7 times and 1·9 times greater, respectively. The best compromise in yield (0·45 g Mn++/g molasses) and rate ofdissolution (0·73 gMn++/l/d) was at 1 per cent (w/v) molasses in a stirred reactor.Where leaching organisms were separated from sterile ore by a bacteria impermeable membrane leaching was shown to be some 20 per cent due to diffusible metabolites and 80 per cent due to a direct contact between the bacteria and the ore particle's surfaces.

Jan 1, 1986

By James JV, Petho SZ

The South Deep surface shaft system is being sunk to a final depth of 2750 in below surface and on completion will be the deepest single drop haft in the world. The shafts will intersect the target reef horizon at 2650 to below surface. In order to negate the requirement for a shaft pillar, which would he extremely large at this depth, the reef horizon in the vicinity of the intersection is currently being mined. A high quality crushed waste/classified tailings backfill is being placed in the longwall stoping panels around the shaft intersection area. This kill limit closure and ride which following shaft reef intersection could have a detrimental effect on the long term shaft stability. This paper discusses underground instrumentation results and numerical modelling exercises carried out to confirm that the shaft system will he stable throughout the life of the mine. Instrumentation projects include closure and ride measured between backfill paddocks and haulage leveling exercises carried out to determine the far field rockmass response to mining with stiff backfill.

Jan 1, 1998

By Dyson N. F

Mixed cobalt-nickel sulphides precipitated from ammoniacal process liquors derived from nickel sulphide concentrates, mattes, and reduced nickeliferous laterites have been characterized.The mixed sulphides are prone to oxidation on standing and are rapidly leached under relatively mild conditions. The kinetics of the leaching reactions are controlled principally by temperature and oxygen partial pressure. Although the samples have different CO:Ni ratios and have undergone varying degrees of oxidation, there is little difference in their leaching behaviour. The results suggest that a single plant would be able to process mixed sulphides of varying composition. Any copper and zinc present in the mixed sulphides as impurities also go into solution and must be removed prior to recovery of the cobalt and nickel in metallic form.

Jan 1, 1981

When xanthates or dithiophosphates are used as collectors in sulphide ore flotation, adsorbed species may be identified by gas chromatography of the volatile products formed during low temperature pyrolysis. For collector additions ,as low as 20 g/tonne of ore, pyrolysis of the flotation products usually gives' an olefin directly related to the particular xanthate or Aerofloat reagent used. The method is able to provide valuable qualitative and quantitative data relating to the extent of collector adsorption and the resulting changes in the hydrophilic or hydrophobic nature of the mineral surface.

Jan 1, 1974

By P Vass, C Butler, J Condon, B Hooper

DeGrussa Copper Mine, resource status 10.2 Mt at 5.7 per cent Cu, 2.1 g/t Au (Sandfire Resources, 2013), commenced concentrate production through its 1.5 Mt/a conventional copper flotation processing plant in September 2012. Geometallurgical assessment during the feasibility study identified potential process-critical ore factors that required further investigation to determine potential impact on processing. Ore characterisation and metallurgical processing performance test work of ore types ensued and subsequently, the first quantitative DeGrussa geometallurgy model was born. Now one year into steady state production, the geometallurgical program has evolved significantly from its infancy and provides valuable insight into ore characterisation and behaviour in the processing plant. This paper details geometallurgical investigations undertaken at DeGrussa to date; from feasibility metallurgical test work through to geometallurgical modelling and management practices, as well as reconciliation between observations at feasibility study level and subsequent observations in production.CITATION:Condon, J, Butler, C, Hooper, B and Vass, P, 2013. DeGrussa Copper Mine, Western Australia - feasibility to first production: a case study in developing a working geometallurgy model from first principles, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 59-66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

Alluvial gold was found in the Terawhiti area, West of Wellington, in the 1850s. This led to the discovery of reef gold. Periods of minor 'gold fever', company flotations, and mining activity occured between 1869 - 1973, 1881 - 1986, and in the late 1880s, with one final company active in 1911 - 1914. 1n the early 1980s, further field work was carried out. No viable mining operations resulted from any of this activity.

Jan 1, 1993

By C D. McCullough, M Gerner

Rarely do opportunities arise allowing closure of a mine site to be planned as a key beneficial land use asset within a new urban growth area; particularly so well prior to cessation of mining.Pit lakes are common mine closure legacies for many open cut mines and may form in open cut mine voids extending below the water table upon closure. Mine closure guidelines increasingly require post-mining land uses of equivalent capacity to premining conditions and that minimise long-term post-mining liabilities and maximise benefits to stakeholders and the environment. However, risks presented by pit lakes are regularly neglected in closure planning or are not able to be addressed to allow beneficial end use of the lake or surrounding land.This paper describes strategic planning initiated by quarry owners ten years before mining ceases. In liaison with the planning agencies, the planned closure of a large 100-year-old limestone quarry pit will form a lake on mine completion, with a well-considered beneficial end use in an urban setting in mind. The quarry pit and adjoining land at Batesford South about the edge of the City of Greater Geelong, Victoria, Australia. Geelong is experiencing growth pressures that necessitate development of a new growth area from about 2025.A multidisciplinary expert team assessed the constraints, opportunities and feasibility of rehabilitating the quarry and pit lake and developing the surrounding land as Geelong’s next urban growth area.The concept is exciting and demonstrates that a former mine site could become a valued home to about 40 000–45 000 people. About 30 per cent of the land will also be developed as an ecological riverine corridor including the pit lake that will become a regionally iconic lake as the centrepiece of an urban development.Our paper outlines technical challenges and how these can be met to achieve closure and beneficial use that meets the social, economic and environmental expectations of contemporary urban planning.CITATION:Gerner, M and McCullough, C?D, 2014. Planning for the future – development of beneficial end use from a quarry pit lake, Victoria, Australia, in Proceedings Life-of-Mine 2014 , pp 99–112 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By McIntosh A. H, Torlach J. A

Since the last paper on mining methods was presented to the Annual Conference of the Australasian Institute of Mining and Metallurgy in 1:960, numerous advances have been made in drilling and blasting techniques at Mount Morgan. This paper describes the drilling and blasting methods being employed in the open cut. The change over to track mounted percussion drills for all types of primary drilling is almost complete and new techniques such as detergent drilling and pressure loading of ANFO are being applied successfully.

Jan 1, 1965

By A K. Raina, V M. S R Murthy

Rock mass response in blasting is an important element to determine the performance of a blast along with its other outcomes. The near-field monitoring for rock mass response analysis is vital for determining the behaviour of a blast; however, due to costly and cumbersome methods involved in such measurements the subject has received scant attention so far and the publications on this account are perfunctory in nature. This paper presents a non-destructive method to monitor the blast-induced pressure in the rock mass at a distance from a blasthole. The methodology of monitoring and a few examples of actual field monitoring are detailed in this paper. The responses of the rock in the near-field of a blasthole under dynamic loading have been documented to predict fragmentation and throw. The proposed method has also been used in limited cases earlier by the author to predict flyrock using a semi-empirical method and trajectory equation. The pros and cons of the method are discussed while throwing light on the actual response and the prediction of fragmentation and throw of blasted rock.CITATION:Raina, A K and Murthy, V M S R, 2015. Measurement of blast-induced pressure in bench blasting and deciphering explosive performance through rock mass response analysis – a methodology, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 501–508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By B A. Webler, P Su, P C. Pistorius

Advanced high-strength steels (AHSS) typically have much higher aluminium concentrations (by an order of magnitude or more) than conventional low-carbon aluminium-killed steels. The resulting lower oxygen activity at the steel-slag interface changes the kinetics and thermodynamics of steelslag reactions. Previous work showed that the rapid transformation of alumina inclusions to spinel inclusions, and spinel to periclase, occurs because of the relatively high concentration of dissolved magnesium. In this paper, experimental results on nitrogen removal by ladle slag are compared with predictions based on the available thermodynamic databases. As in previous work, the kinetics was modelled by assuming mass transfer control, with steel or slag mass transfer limiting. The results show that significant removal of nitrogen by steel-slag reaction is possible.

Aug 21, 2024

By AMIRA P588 Research Team

This contribution summarises new knowledge and data, obtained during a three year ARCAMIRA funded research project, on the mineralogical and geochemical characteristics of hydrothermal alteration associated with low sulfidation, gold-silver epithermal deposits. These data are used to develop exploration vectors for use at both deposit and district scales, plus techniques have been established to distinguish ore grade epithermal systems from barren or low grade systems. Deposits investigated were Ladolam, Papua New Guinea, Gosowong and Mt Muro, Indonesia, Cerro Vaguardia, Argentina and Bimurra and Twin Hills, Australia.

Jan 1, 2005

By J Stipcevich, N Patel, J Faithful5, S Narendranathan, L Tatnell4

ENGIE, the current owner and operator of the Hazelwood Open Cut coalmine, are in the process of rehabilitating the mine site in preparation for mine closure. Bucket wheel excavators (dredgers) used during coal mining operations are in the process of being demolished, which involves the controlled felling of dredger components using explosives. With the mine located in close proximity to the Morwell township and other critical public infrastructure, it is crucial that the use of explosives and the possible implications for mine stability is well understood. The felling of Large Mining Equipment (LME) will apply an impact load immediately to the underlying coal benches with the adjacent coal batters potentially at risk also of adverse slope stability impacts. This paper presents the 3D stability modelling methods employed to successfully assess the potentially adverse stability implications associated with LME collapse.

Jun 21, 2022

By E Nye and T Schroeter, B Muir, M Kitson, M Gonzalez, D Mares

The single track North Strathfield Rail Underpass (NSRU) consists of a dive structure either end of a 148 m long driven tunnel skewed under three live railway tracks. The tunnel is 8 m high, 9 m wide, with a horseshoe profile, excavated by full face using a road header. Ground cover varied between 2.5 m to 3.5 m. Settlements were 5 mm to 15 mm (the latter due to a dyke). A one pass synthetic fibre reinforced shotcrete lining was installed (no lattice girders or steel sets were used). A system of automated robotic total stations was used to provide real time monitoring of the rail track and associated ground formation. No disruption to train services occurred.CITATION:Gonzalez, M, Kitson, M, Mares, D, Muir, B, Nye, E and Schroeter, T, 2014. The North Strathfield Rail Underpass – driven tunnel design and construction, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 369–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By C A. Myburgh, S Craig, K Deb

In focusing on open pit mine scheduling, one of the biggest areas that a mining engineer can add value is in the area of cut-off grade optimisation. It is not atypical to add up to an extra 20 per cent in value by bringing forward higher-grade ore and deferring costs into the future.There are many techniques available to maximise net present value (NPV) when applied to open pit mine scheduling. That in itself raises the question of why so many of these techniques exist. The short answer is that none of these techniques are robust. Every time the problem changes, the algorithms also have to change.Instead of trying to make a problem fit the constraints of an existing technique, there is much to be said for usefully hybridising different approaches. This paper describes an innovative approach where evolutionary algorithms are combined with both local search and linear programming. The goal is maximising NPV through optimisation of cut-off grade policy and extraction sequence for an open pit mine. The cut-off/cut-over grade policy produced caters for multiple processing streams and stockpiles.Finally we demonstrate the quality of the algorithm by comparing some results with a well-known mathematical solution.CITATION:Myburgh, C A, Deb, K and Craig, S, 2014. Applying modern heuristics to maximising net present value through cut-off grade optimisation, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 155–164 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

Support design in jointed or blocky rock masses is often approached by the use of either 'rules of thumb', rock mass classification systems such as the Q-system (Barton, Lien and Lunde, 1974) or RMR (Bieniawski, 1973) or conventional wedge analysis. Generally, this requires that a number of key simplifying assumptions are made and the support system is designed to cater for either a mean, most likely, or worst case scenario depending on the risk tolerance. The design block size is often a major uncertainty and often a worst case block size based on excavation span is used. Thompson and Windsor (2007) state that it is inappropriate to base support designs on the excavation size as these size blocks rarely occur if discontinuity trace lengths are considered. Probabilistic keyblock methods can be used to determine the most likely design block sizes. A methodology is presented whereby JBlock software (Estherhuizen, 1996) is used to estimate potential block sizes as part of the support design process. Using information such as the spacing, orientation and length of discontinuities, it is possible to simulate blocks in the walls of an excavation (Esterhuizen and Streuders, 1998). Keyblock analysis methods (Goodman and Shi, 1985) are used to evaluate whether blocks are removable and whether the chosen support will be sufficient to ensure stability. Data from two mines is used to demonstrate how probabilistic keyblock analyses can be used in support design. Discontinuity data was used to generate 10 000 removable blocks and the design block size statistics were determined. For one mine this information was used to scale blocks in a conventional. Unwedge analysis whilst for the other mine, the point estimate method (Harr, 1987) was applied. The choice of appropriate design acceptance criteria in terms of factor of safety and probability of failure is also considered.

Nov 25, 2010

By J Välivaara

The mining industry will face numerous challenges over the next 10–15 years as new deposits are likely to be more remote and lower grade and existing deposits will be mined deeper. As a result, mines and mining contractors operating in deep-mine conditions will need to focus on the quality of drilling and blasting to minimise unnecessary waste rock excavation to keep costs at an acceptable level. In addition, increased demand for improved safety and operator ergonomics will set greater demands on original equipment manufacturers of mining equipment. Finally, difficulties finding a skilled and experienced workforce, particularly in remote mine locations, have already negatively impacted mines’ ability to achieve high productivity and low operating costs.This paper introduces techniques and shares practical experiences in increasing productivity and reducing the costs of excavation in underground face drilling. The paper uses Sandvik’s new DD422i automated mining jumbo as an example of the type of equipment needed to deliver the features and corresponding benefits for future mine development. Case studies using this equipment are presented to illustrate the points made in this paper.CITATION:Välivaara, J, 2016. Automated drilling features for improving productivity and reducing costs in underground development, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 723–730 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R Minnitt

Two methods of calibrating the parameters K and Alpha for use in Gy’s formula for the fundamental sampling error were investigated. Approximately 480 kg of broken ore from Harmony’s Target gold mine in South Africa was used to compile the replicate samples for two experiments. The duplicate series analysis (DSA) and segregation free analysis (SFA) methods differ in terms of their approach to recovering the sized materials required for the calibration procedure. In this experiment the DSA method split off six more-or-less equal masses of material from a 75 kg lot that was successively crushed to finer and finer fragment sizes. The sublots so formed were split into 32 samples and fire assayed for gold. The SFA method used approximately 250 kg of broken ore crushed to 95 per cent passing 2.50 cm, which was then passed through successively finer screens until a sublot of less than 0.0075 cm was obtained. Each of the 15 sublots obtained in this way were split using a riffle splitter into 32 samples that were fire assayed. A total of 672 fire assays were used in these experiments. The sampling parameters K and Alpha were used for the compilation of a nomogram and to calculate the gold liberation size of the ores. While there are no definitive results in terms of the actual gold grain sizes against which the calculated sizes can be compared, it appears that the DSA method produces more acceptable results.CITATION:Minnitt, R, 2014. A comparison of two methods for calculating the constants K and alpha in a broken ore, in Proceedings Sampling 2014 , pp 165–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By T Elms, R Beckman, M Sampson

"In today’s mining industry, the pressure of reducing costs and increasing production while maintaining high safety standards is at the forefront of operational endeavours. A combination of specific mining knowledge and technological advances has helped enable this notion. Fleet management systems have been developed to enable sites to better measure and manage production to improve operational efficiency.The integral part to managing production is having accurate, readily accessible data. This empowers key stakeholders in the management team to drive production reporting, materials tracking and budget forecasting.If a site does not run a fleet management system, manual input is heavily relied upon for production data, which introduces increased risk of human input error. Errors can drive outcomes that don’t achieve increased production at a reduced cost. Alternatively, a fleet management system can have improved accuracy but involves a high monetary investment. Such an investment is not always feasible for smaller mining operations subject to current industry cost pressures.The Emeco Operating System has been developed in alliance with sites such as the Mungari White Foil Operations by satisfying the criteria of a low intensity hardware installation, material tracking data validation processes, remote monitoring, identification of metrics to improve overall operating efficiency and providing the right information to key stakeholders.Citation:Beckman, R, Elms, T and Sampson, M, 2016. Getting Accurate Mine Information to the Right Teams to Drive Production Improvement, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 203–211 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By P Clark

This paper discusses the challenges, solutions and lessons learnt as tunnelling work continues on the Melbourne Main Sewer Replacement (MMSR) project.The MMSR project is a $220 million dollar project for the Melbourne Water Corporation. It involves the construction of approximately 4.2 km of new sewer from the southern fringe of the CBD through the inner metropolitan suburbs of Port Melbourne and South Melbourne.Of the 4.2 km of sewer currently in construction approximately 2.2 km will be constructed using a 2.95 m diameter Lovat EPB tunnel boring machine (TBM) with approximately 1.9 km of small diameter (300 to 600 mm) reticulation sewers constructed using trenchless techniques.These sewers are being constructed in a dense urban environment, which means that the tunnels and shafts are often in close proximity to buildings and structures. The underground constructionof the sewer is further complicated by the variable geology of the ancient Yarra River delta which includes weathered basalts, the infamous Coode island silt formation and fine loose sands.Some of the key challenges and lessons learnt so far during construction include:· steering and alignment control of the TBM through very soft silt with little residual strength,· development and refinement of a monitoring and alarm system for leaving the machine dormant on a day works only project,· control and measurement of tunnel lining defl ection during ring build and grouting,· prediction and monitoring of surface settlements during tunnel excavation,· improved understanding of the geology and hydrogeology at this previously unchartered area of Melbourne,· consolidation settlement due to dewatering at shafts required careful construction controls, and· ground support and excavation in close proximity to the existing 110 year old sewer which requiredvery detailed risk control measures.

Mar 8, 2011