Search Documents

By G M. Volkmann

Pipe umbrella support systems – also called canopy tube systems – have been used successfully for tunnelling in challenging ground conditions since the 1970s. Historically, the drilling unit was the limiting factor for pipe umbrella installations – less attention has been paid to pipe couplings and their influence on labour time and load-bearing capacity.This contribution investigates the influence of the type of pipe connection on the load bearing characteristics of a connected pipe and discusses associated influences on design calculations and installation performance. Standard thread connections reduce the effective cross-section and thereby load-bearing capacity in the connection area. To achieve design parameters, over-dimensioning of the un-weakened pipe section is the only way to overcome this limitation. Recently, two new, alternative connection types were designed and developed for connected pipe umbrella pipes. The first one is the nipple coupling, consisting of fitting with a threaded connection that is pressed and welded into the ends of standard tubes. The second type is the squeezed connection, which mechanically connects non-threaded pipe ends, achieved by force-fitted squeezing from the drill rig. Both coupling types have technical as well as operational advantages compared to the common thread couplings, which are the weakest point in the support system.In the following sections significant technical differences are explained, design values given and a site example presented to illustrate the operational advantages of the newly developed coupling?type.CITATION:Volkmann, G M, 2014. Development of state-of-the-art connection types for pipe umbrella support systems, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 333–338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By R Byrnes, P Hensley

The outstanding environmental management initiatives undertaken by Novacoal at its Western Main Site near Lithgow in New South Wales over the past five years are detailed in this paper. These initiatives have been based on a combination of proven and innovative investigation and implementation techniques, close consultation with regulatory authorities and full support by colliery management. The results of these initiatives have enabled the colliery to exceed its pollution control obligations from a base well below industry standards. The initial poor condition of the mine was the result of over 50 years of traditional mining which paid little regard to environmental management. The transformation of the colliery within such a short period, with limited capital, is considered a model for the N.S.W. coal industry.

Jan 1, 1995

By Robertson K. S, Hunter T. C

AEG-Elotherm's electromagnetic dosing channel, or Eldomet, is a recent invention enabling the transport and metering of molten metals. The development of a reliable refract- ory lining, and the use of suitable construct- ion and operating techniques has led to the successful application of the Eldomet for casting copper anodes at Copper Refineries Pty. Ltd.

Jan 1, 1974

By P Craig, I Canbulat, J Naylor, J Emery, A Sykes

Longwall mining is by far the most common method of underground coal extraction in Australia. Industry trends and expectations are placing increasing emphasis on the reliability and productivity of these operations. Longwalls are becoming wider and longer while retreat rates are continuously increasing due to significant improvements achieved in longwall equipment reliability and automation. This increased longwall productivity is placing significant emphasis on the reliability of longwall panel development.Although there have been significant improvements in the reliability of continuous miners and hydraulic drill rigs, the traditional resin-encapsulated bolt installation is still the principal method used in all major coal producing countries around the world. Anglo American realised that an opportunity existed to introduce an alternative roof bolt installation technique called ‘spin-to-stall’ (STS) into Australia. STS was first introduced by Anglo American Coal in South Africa, where it has been successfully used for over a decade, though implementation of South African STS resin in Australia has proven to be near impossible. Therefore, a new STS development project was initiated between Anglo American Coal and Jennmar Australia. This paper summarises the journey of this project, the results achieved and the successful implementation of STS at Grasstree mine.CITATION:Emery, J, Canbulat, I, Craig, P, Naylor, J and Sykes, A, 2014. Development and implementation of spin-to-stall resin at Anglo American’s Australian Underground Coal Operations, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 287–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Mine F. J, Woods P. H

The Top End of the Northern Territory lies in the monsoonal zone and receives rain during the November-April period. Initially, at the start of the wet season, rain storms are localised, but, following the descent of the monsoonal trough from below the equator, widespread rain occurs. Overflow incidents at mine sites tend to arise midway through the annual wet season when excess water accumulated in ponds begins to discharge to the external environment. Remote-access monitoring may be undertaken at mine sites using equipment to continuously measure water quality parameters with storage of the information on a data logger. The data is then retrieved by visiting the site and transferring it to a portable computer or by remotely accessing the system using a telemetry system and transmission via telephone, VHF/UHF or satellite. Such systems are readily available and vary in cost depending on the sophistication of the data transfer system. Available sensors for continuous monitoring include those for conductivity, temperature, pH and other ion selective electrodes, eg nitrate, and water level. Of these variables, conductivity is most useful due to its inherent accuracy and stability of reading. Remote monitoring capability is able to provide: (i) more intensive monitoring of key issues; (ii) more timely information; (iii) correct perspective on the degree of environmental problem; and (iv) information from remote locations, which would be difficult to monitor by more conventional methods. Examples are given for applications of continuously logged measurement of conductivity of waters discharging to drains and in creeks at Pine Creek, Ranger, Nabarlek and Woodcutters mines in the Northern Territory. These applications demonstrate the timeliness of the continuous monitoring technique.

Jan 1, 1994

The intent of this address is to look forward into the 21st Century and present certain thoughts as to how underground coal mining might be conducted. The views in this talk are based principally on the author's experience with mining practices in the United States. It may be difficult to accept, but the 21st Century is a mere 12 years away. What new techniques will be available? To develop an understanding of the way in which technology has been and could be changing, a two- stage analysis is made of mining technology for U.S. Coal. The first phase covers the period 1975 to the present, while the second includes 1960 to 1975. This historical perspective includes a view of underground production by mining methods, considerations of labour productivity, and a review of accident and fatality rates. Several topics are important features of this historical analysis. Among the most significant are: (1) the introduction of Ion-wall mining technology into U.S. underground coal mines, (2) the use of computers to assist in mine planning and design activities, (3) major efforts to improve health and safety performance, with emphasis on underground dust control, and (4) improvements in mining equipment with an eye towards increased reliability and up-time performance. Based on that historical perspective, projections are made in three increments. The first being immediately at the turn of the century, the second being a dozen or so years beyond that, and the third being at the quarter point of the 21st Century.

Jan 1, 1988

By J Kinal, P Steinier

A considerable volume of work exists in the literature examining the electrochemical interactions between grinding media and sulfide minerals. Broadly, most sulfide minerals are more noble than forged steel grinding media used during comminution, therefore a galvanic couple between the media and the sulfide mineral(s) exists, which increases the corrosion rate of the grinding media. The corrosion products of the grinding media, iron oxy-hydroxide species, invariably precipitate on to the surfaces of the sulfide minerals thereby affecting their floatability. This paper explores the science behind these corrosion reactions, and provides an explanation of their impact on the pulp chemistry of sulfide mineral slurries and subsequent flotation behaviour. A number of laboratory and plant case studies are used to illustrate the benefits of changing to a more inert grinding media.

Jan 1, 2005

By J Ashford, Minniakhmetov

Geostatistical simulations are the best practice for uncertainty quantification in non-linear systems. Simulations are currently undertaken on an ad hoc basis in the mining industry due to high requirements in computing environments and advanced geostatistics. In contrast to the estimation process, multivariate simulations can be performed using different methods, tools, and computational environments, similar to data science. For large companies with multiple commodities it is important to have a standard framework to test, build, and run workflows using different methods, applications and computational environments. This work presents an auditable, modular and scalable framework to create geostatistical simulation workflows where the workflow is abstracted from the implementation. Key aspects: automation – workflows should be able to run automatically given updated data (if hands on modelling is not required); auditability – workflows should document key considerations and parameters; modularisation – workflows should permit swapping out components, for example substituting domaining in Leapfrog software with automated domaining using machine learning scripts; scalability – easy, repeatable, portable deployments on diverse infrastructure (for example, experimenting on a laptop, then moving to an on premise cluster or to the Cloud); reproducibility – parameters should be archived to permit re-running and reproduction of workflows in future years; and sensitivity analysis – any component of a workflow should be able to run with multiple scenarios of parameters and data to enable global uncertainty quantification and sensitivity analysis. The presented framework can be used to create different workflows for geostatistical simulations in multiple assets to quantify uncertainty in the value chain for resource categorisation, reserves uncertainty, value of information and robust mine planning amongst others.

Mar 22, 2022

By L A. Balzan, F Nieuwenhuys

GEOSCAN on belt analysers have been widely utilised in iron ore for nearly two decades. Since the first installations in 2003, the availability of accurate and reliable grade data has become standardised across iron ore mines in the Northern Cape in South Africa, where various streams are monitored continuously to ensure the optimal functioning of plants. Assmang Khumani has been at the forefront of technology adoption, and has implemented 19 GEOSCANs at various locations throughout the plant, monitoring run-of-mine, stockyard feed, beneficiation plant feeds, and products. Over the years, collaborative advances in the technology have allowed for numerous benefits and gains to be made. In recent times, there has been a concerted effort on the development of analysis for phosphorus in the material flows, and based on Scantech’s experience in the phosphate industry, this element has now been calibrated to achieve statistically acceptable and repeatable accuracies for real time analysis of this element on many of Khumani’s GEOSCAN analysers. This paper provides an overview of GEOSCAN use at Khumani, while focusing on the development of phosphorus analysis. A case study of analysis results is presented for a range of analysers that have been calibrated for this element, as well as a discussion on the benefits obtained as a result of this analysis.

Nov 8, 2021

By I M. Platten, Y Xie, B W. Cuffley, S C. Dominy

"Geometallurgical programs require the collection of representative samples for geochemical, mineralogical and metallurgical test work. Such protocols must be designed to suit the style of orebody in question. The distribution, proportion and size of gold particles have a direct impact on the effectiveness of sampling and test work protocols, and the gold recovery processes employed. Characterisation studies focusing on ore mineralogy, and gold particle deportment, size and distribution are required. High resolution X-ray computed tomography provides a non-destructive method for analysing the 3D nature of gold in rock samples. It can be used to calculate the modal abundance, particle size and distribution of gold in the sample volume. This paper presents a case study of the imaging of in situ gold particles in a high-grade gold ore. The Nick O’Time reef system comprises laminated quartz veins, which locally bear extreme grades of up to 100 oz/t gold. The mineralisation has previously been characterised from both a mineralogical and metallurgical perspective. Eight visible gold-bearing vein samples were scanned using X-ray microtomography. Microtomographic data were integrated with previous mineralogical and metallurgical test work outputs.CITATION:Dominy, S C, Platten, I M, Xie, Y, Cuffley, B W and O’Connor, L, 2016. Characterisation of Gold Ore from the Nick O’Time Shoot (Tarnagulla, Australia) Using High Resolution X-ray Computed Tomography, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 241–254 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By T Tan, C P. Holmes, C E. Hartford

Transportation of iron ore from the mine to the plant is critical to business success. Ore from the mine may have to be transported across states, countries and even continents to get to the processing plant or export facilities, and ultimately to the client. Numerous transportation steps may result in potential logistical difficulties. Companies are continually seeking ways to increase production rates, decrease delivery times and reduce operating costs. Transportation cost is a major component of the total cost of mining iron ore and therefore requires effective use of transport systems.Bottlenecks in iron ore transport systems, due to material handling issues, can result in loss in profit in the order of millions of dollars per hour. Bottlenecks can be seen anywhere in the transport system where the desired flow rate cannot be achieved. These bottlenecks occur for various reasons such as increasing throughput in a transport system originally designed for a lower throughput resulting in plugged transfer chutes, changing material characteristics (eg finer material, increased moisture content), changing to a new type of material or blend that again alters handleability, or changes in operational philosophy due to equipment availability or process utilisation.Stockpiles may have limited live capacity such that an adequate amount of ore may not be readily reclaimed when required (eg to fill a complete train’s railcars). In bins and hoppers, material may discharge through a central flow channel resulting in the formation of a stable rathole, which can then collapse causing material to flood the downstream system and cause significant downtime for clean-up (eg railcars beneath train load outs). In transfer chutes, bottlenecks can be caused by pluggages or downtime required for the change-out of liners due to excessive wear. In ship loading, long settling or de-aeration time, or material exceeding its transportable moisture limit (TML) may result in further bottlenecks. These bottlenecks all have associated costs because of the need to address their causes and because of the lost opportunities for throughput.This paper will discuss how bulk material technology and proper understanding of material flow characteristics can be applied to mitigate bottlenecks. It will discuss how to predict potential bottleneck locations through a scientific method of analysis and evaluation to determine if an increase in throughput of an existing transport system is possible, as well as whether or not a new material will flow reliably through an existing system.CITATION:Hartford, C E, Holmes, C P and Tan, T, 2015. De-bottlenecking iron ore transportation from mine to plant, in Proceedings Iron Ore 2015, pp 393–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

Study on Pure Mineral Flotation Tests of Low-Grade Phosphate Ore in Zhijin, Guizhou Province, China

Sep 13, 2010

Good morning ladies and gentlemen, and may I thank you for inviting me once again to address your conference. I would first like to welcome you all, especially international delegates and conference speakers. ItÆs a pleasure to be with you all and I hope that you have the time to enjoy the many beautiful sights that the Coromandel and Bay of Plenty have to offer.   Holding your conference in Waihi is particularly apt, especially bearing in mind the conference theme û 'Mining in the Community'. There can be few venues in the world that can boast a world class gold deposit of the likes of Martha Hill located right here in the centre of a rural service town. ItÆs a deposit that has a mining history active now in its third century and that to date has yielded some 7.5 million ounces of gold and 50 million ounces of silver. I doubt that when John McCombie and Robert Lee discovered gold at Martha Hill in 1878 that they had any inkling that their endeavours would be the foundation for a mine that would become such an inseparable part of the economic and social fabric of Waihi for the next 130 years.   This is now my fifth appearance at a New Zealand minerals conference, I especially value such occasions as it allows me to comment on your industryÆs performance over the past year, share my thoughts on matters affecting your industry, and also to give you some feedback from central government.

Jan 1, 2006

By W J Fisher

Northern Australia leads in world-class mineral deposits' is a bold statement. First there must be a starting point. Land north of the Tropic of Capricorn (23¦ 26' 5") will be regarded as Northern Australia covering nearly 40 per cent of the land surface of Australia. As opposed to land south of the Tropic of Capricorn, it should be regarded as Tropical Northern Australia and for the sake of brevity, (TNA) Refer Figure 1. Apart from the tyranny of distance from centres of power and population in the temperate zone, it suffered in the past from the belief that the tropics are unsuited for European workers and from the lack of infrastructure. Outstanding mineral deposits of iron, base metals, gold and diamonds, discovered and developed in the past three decades, provided the substance for the title. There are many world-class mines producing and there are mineral deposits neutralised through Government policy. TNA can maintain its lead in world-class mineral deposits provided Government policy will stop partitioning the land and decreasing that available for exploration. Let's look at what we have that is world-class. In Western TNA iron ore deposits at Paraburdoo, Mt Tom Price, Marandoo, gold at Telfer, diamonds at Argyle. In central TNA uranium at Ranger and Jabiluka, lead-zinc-silver at McArthur River, gold at the Tanami, manganese at Groote Eylandt and bauxite at Gove. In eastern TNA Mt Isa, Hilton, Century zinc-lead, bauxite at Weipa, gold at Kidston, Mt Leyshon, magnesite at Yamba and coal mines in the Bowen Basin. Those mines or deposits stand out yet are only an indication of the numerous lesser mines and of mineral deposits depending for development on market demand and/or changes in Government policy, eg 'The Three Mines' policy. Very large areas of mineral rich structures in the western, central and eastern parts of TNA are concealed below flat lying comparatively young unmineralised sediments. The Great Artisan basin sediments in eastern TNA can and do host oil shale and non metallic minerals. Nearly 40 per cent of western TNA is covered by the Great Sandy Desert. The Canning Track, with a series of 54 wells, was constructed by surveyor Alfred Canning in 1908 - 1910 with great difficulty. It extends 1700 kilometres from Halls Creek in the north to the gold town of Wiluna in the south, through the Great and Little Sandy Deserts. Gold explorers are following favourable structures extending to the north east below the sediments and sand hills covering the track. Half of central TNA's mineral structures are concealed by the Tanami desert and the Cretaceous sediments covering the pastoral regions of the Barkly Tableland and the Daly Waters to Top Springs pastoral areas. The Georgina Basin in the south eastern section is part of the concealment.

Jan 1, 1994

By H A. Linn, K Winn, C W. Lee

The Q-slope method for rock slope engineering was developed to enable engineering geologists and rock engineers to rapidly assess the stability of excavated rock slopes in the field and make optimal adjustments to slope angles as rock mass conditions become apparent during construction of road cuts or benches. An empirical relationship between Q-slope and long-term stable slope angle is now supported through over 500 cases studies from Asia, Australia, the Americas and Europe. This paper presents about the stability analysis by first-ever applying Q-slope method on abandoned quarry wall in Singapore. The 30 m high rock slope which is composed of monzogranite rock was severely damaged by blasting operation. As the rock slope is intended for public view the objective was to retain the natural outlook and without any artificial support application thus manual scaling was carried out to clear the loosed rock blocks. In the end stable slope angle of clean rock face is determined once again by Q-slope method.

Nov 29, 2022

By W B. Edgar, S C. Dominy

High-nugget effect vein-gold systems are generally considered to be one of the most challenging of deposit types to evaluate and exploit. To potential investors and mining companies, they are viewed as high risk because of the associated uncertainties in the grade estimate and general paucity of Ore Reserves at production start-up. However, despite the well-known risks, these deposits often have a grade upside that makes them potentially attractive. The reporting of resource grade is of importance and perhaps even more so is the reporting of the associated uncertainty attached to the grade estimate. The use of the grade estimate supported by a grade range is recommended to achieve more complete and useful disclosure. The definition of the grade range can be somewhat subjective, ranging from opinion based estimates through to data-based estimates and geostatistical conditional simulation. Whichever method used, the over-riding issue must be the provision of enough data of appropriate quality and full disclosure to the public of relevant uncertainties.CITATION:Dominy, S C and Edgar, W B, 2012. Approaches to reporting grade uncertainty in high-nugget gold vein projects, in Proceedings Project Evaluation 2012 , pp 95-108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By G J. Zhang

The shape and particle size distribution of caved ore mass in sublevel caving were investigated in this study. The paper first reviews the main factors affecting the shape and characteristic of caved ore mass in sublevel caving and then through the experimental blast testing with cement-sand concrete models, the shape and particle size distribution of caved ore mass were found out. The experimental results indicated that the shape and particle size distribution of caved ore mass was similar to that of the drawn loose body. This finding presented a new perspective for the future study on the ore drawing theory and on the optimisation of structural parameters of sublevel caving. The structural parameters must meet the principle that the shape of the drawn body is in consistency to the shape of caved ore mass.

Jul 11, 2011

In choosing such a threadbare subject for a paper I fear that I may in some measure be taxing your patience, yet as upon the accuracy with which the work is done depends the result of conclusions drawn as to whether a property will be profitable to work or otherwise. The subject cannot be too well threshed out, and I trust that upon certain points that have come within my own experience I may be able to give 'hints that will prevent others from making mistakes. First as to alluvial. Gold is often found from the grass roots down, often ill particular horizontal bands in the wash, but more generally concentrated either on a true or false bottom. When sampling dry ground for proposed hydraulicing I have obtained accurate results only by taking the whole of the dirt from measured shafts, stacking it as it was lifted on a tarpaulin, and putting the whole quantity through a carefully constructed box. In wet ground careful borings will in most cases give fairly correct results, but where it is possible to sink shafts, that should be done, as a guide is then also obtained as to the nature of the wash, whether it is bouldery, cemented, or free. Sampling in a face is a more difficult work in many respects than in new ground, as so many elements enter into action to spoil accurate sampling. Of course the great thing to avoid is sampling in any place where either natural or artificial concentration has taken place, and very much has to be left to circumstance and the sampler's own judgment. In passing I may mention that I have on several occasions seen diggers deceive themselves in wet ground where they were sinking and coping as best they might with water. They would take a dish of dirt from the bottom of their hole, pan it off, and take the result as a fair yield, and on the strength of it perhaps spend a lot of time and money in tail races and whereas in their sample there had been a process of concentration carried on, the movement and working in the water had caused the gold to work down, and anything like accurate estimations by the method pursued were out of the question.

By M E. Dunphy, P Silversmith

The Reefton Goldfield, both historically and potentially, represents a significant gold producing camp in the Westland province of New Zealand. Some two million ounces of gold have been produced from the Greenland Group host rocks between 1870 and 1951 with the most significant producers being the Blackwater and Globe Progress mines.   Steep terrain, high rainfall, poor outcrop, widespread fluvio-glacial deposits, tertiary cover and sometimes onerous environmental access conditions have proved a challenge to conventional exploration techniques. In addition classic exploration techniques have come up against a desire to reduce exploration cycle time and exploration costs while increasing both quality and quantity of geological information.   The trial, and subsequent implementation, of Wacker sampling has proved a highly successful and effective geochemical tool currently being utilised to target, discover, and define potential economic gold mineralisation in the Reefton Goldfield.

Jan 1, 1997

By T Atchison

In-pit crushing and conveying (IPCC) systems have come under growing scrutiny as a perceived mitigation to fuel and equipment price fluctuations, labour shortages and the need to move everincreasing volumes of material. Individual vendors and delivery organisations are now offering a sometimes confusing array of systems, particularly for the dig and dump side operations.One system does not suit all operations. This paper seeks to document the factors that should be considered in assessing the suitability of different IPCC systems, with a focus on dig side equipment layouts in particular. These factors include the productivity of the systems, interactions with the drill/blast and bench operation sequence, the ease of relocation, flexibility to changes in the reserve, scalability and compatibility with other elements of the system.

Jul 11, 2011