Search Documents

By K Ehrig, V Liebezeit, Y Li, B Pewkliang, M Smith, E Macmillan

Pre-concentration of low grade ores via the rejection of low/no value materials based on fragment size is the subject of many published papers and studies over the past decade. However, the possibility of upgrading should not limited to low grade ores given the high cost of capital, energy, water, reagents, and ultimately tailings storage across the mining industry. Mining and processing facilities at Olympic Dam consist of an: 1) underground mine where ore is extracted via sublevel open stoping and 2) integrated processing plant located on the surface which produces Cu-cathode, Au-Ag bullion and uranium oxide concentrate. Blasted ore is trucked/trained to underground crushers which produce an ore feed with a product size P80 = -145 mm. Crushed ore is then hoisted to the surface and delivered to the ROM pads via an overland conveyor. The typical copper grade of mill feed is approximately 2 wt%. A rapid assessment of the potential to upgrade Olympic Dam mill feed prior to the ROM pads via rejection of low value materials based on fragment size was completed using existing data. Three separate datasets were utilised to assess the deportment of Cu, U, Au across size ranges of 200 mm down to sub-8 m. Cumulative grade vs cumulative mass distribution graphs for each element were produced. This data clearly demonstrates that Cu, U, Au grades remain constant down to ~212 m, which happens to be the liberation size of the sulfides. Hence, no potential to upgrade the ore stream via rejection of +200 mm - to ~212 m sized materials prior to milling. Mineralisation within the Olympic Dam Fe-oxide Cu-U-Au-Ag deposit (IOCG) occurs as disseminated sulfide grains within granite- to hematite-rich breccias. The typical sulfide grain size is sub-200 m that supports the outcomes of the grade deportment by fragment size study.

Nov 10, 2020

By W A. Peck

Raise boring is the preferred option for constructing ventilation shafts in Australia. The trend has been towards larger diameters and longer single-pass shafts, and if at all possible, reaming through to the surface. The risk of raise failures, due to missed, unforseen or latent ground conditions has therefore been increasing, along with the need for better, more confident stability assessments.While the stability of specific weak zones and structures must be assessed individually, empirical rock mass classification schemes have been successfully used for about the last 20 years to assess general raise stability; eg the McCracken and Stacey method (M&S).Unfortunately M&S, as originally documented in McCracken and Stacey (1989), did not include a database of raise diameter and rock mass conditions versus actual performance. Nor was there a procedure for assessing the risk of failure due to adverse ground conditions. Peck and Lee (2008) published an Australian database of raise bore performance. Raise diameter and ground conditions, in terms of a lower bound Qr value, were presented for 50 cases versus raise performance. This paper updates the 2008 raise performance plot with more and SRF-corrected data. McCracken and Stacey (1989) had previously recommended that additional geotechnical data should be acquired and analysed when the proposed raise plotted on the unstable side of raisebore stability ratio (RSR) = 1.3, but the Australian data used in this study also suggests that all sites with Qr Contributions and sensitivities of various rock mass parameters (RQD, Jn, Ja, Jr, Jw, SRF, time-dependent weathering/deterioration) to raise stability and risk of failure are discussed. Numerous case studies are used to illustrate issues with stability assessments.As raises can now be remotely supported using sprayed fibrecrete, questions of time-dependency are also discussed. In recent times, contiguous piles, ‘mini-piles’ and grouting have also been successfully used to presupport or otherwise improve the stability of near-surface sections of weathered, or poor quality rock masses.

Mar 21, 2011

By J Mauk, J Rowland, S Rabone

Most epithermal Au-Ag deposits in the Hauraki Goldfield are hosted in late Miocene andesites. Broken Hills is an exception, being one of the few economic deposits hosted in rhyolite. Investigation of Broken Hills provides the opportunity to collate structural data that may be compared with that collected from andesite-hosted deposits in order to evaluate the importance of rock type on vein development. The rhyolite host rock at Broken Hills is strongly flow-banded, but this anisotropy does not appear to affect the orientation of mineralised structures. There is a range of structures at Broken Hills: veins, faults, fractures, and large breccia pipes. Veins generally strike north-south, with localised changes in strike and thickness. Slip vectors determined from striations indicate near pure dipslip on the main lode, indicating an extensional tectonic setting. The orientations of vein deflections are parallel to slip vectors. This correlation is common in modern extensional fault arrays where fault growth and linkage produces subvertical deflections in fault orientation (eg TVZ). There are three main types of breccias: 1. Primary breccias related to rhyolite emplacement. 2. Jigsaw type secondary breccias that are that developed during the life of the hydrothermal system. 3. Breccia pipes. Broken Hills was a dynamic epithermal mineralising system.

Jan 1, 2003

By Thompson M

The humble gabion basket is to mine development what the light bulb and safety pin are to eir-ryday life. Gabions provide a flexible, easy to assemble and cost efficient solution for "101" mine and civil engineering development applications.In some instances gabion baskets are still efficiently in use after many years of faithful, maintenance-free service. In other situations, the baskets have been demolished or made redundant within days, either having served their temporary usefulness or negligently destroyed by the operator of heavy equipment. Either way, the gabion basket must surely rate among the top 10 cost efficient engineering construction materials.

Jan 1, 1994

The cloud transform simulation is a technique used to generate realisations of correlated attributes. The principle of this technique is to partition the scatter diagram between the input attributes into several interval classes and derive for each class a cumulative distribution function (CDF) using only the data pairs of the scatter diagram in that class. The simulation then proceeds like a traditional Monte Carlo simulation but using the derived CDF in each class.The cloud transform simulation has the advantage of being a simple and fast technique that is able to reproduce the uncertainty in the relationship between the two input attributes regardless of whether the relationship is linear or not. However, the technique has three major drawbacks. First, the number of classes has an impact on final simulated results and there is not a robust approach to define such number. Second, simulated results exhibit some saw tooth variations that are unrealistic and third the reproduction of the spatial continuity of the simulated attribute is not guaranteed.This paper presents the use of the quantile regression approach in order to overcome the first two disadvantages of the cloud transform simulation. Details of the technique and how it can be coupled with the cloud transform simulation are presented along with a real case study.

Sep 26, 2011

Development of the Boleo Process Flow Sheet and the Direct Solvent Extraction (DSX) Circuit for Cobalt and Zinc Recovery The metallurgical process designed to treat the El Boleo Cu-Co-Zn-Mn ore involves a sulphuric acid leach in seawater under oxidative and then reductive conditions to maximise metal extraction. Copper and cobalt are recovered as cathodes by electrowinning, zinc and manganese as zinc sulphate monohydrate and high quality manganese carbonate, respectively, by precipitation after a number of separation and purification stages. One of the key purification stages of the Boleo metallurgical process is the CSIRO DSX circuit. The DSX circuit was developed using the synergistic solvent extraction (SSX) technology. Initially, a synthetic solution was studied, and by adding 0.4 M LIX63 to 0.5 M Versatic 10 in Shellsol D70, large synergistic shifts were obtained for cobalt (?pH50 4.24) and zinc (?pH50 1.62). After a single contact, the separation factor of metals over manganese reached over 6,000 for cobalt and over 380 for zinc, indicating excellent separation of cobalt and good separation of zinc from manganese, magnesium and calcium. The SSX system was further optimised with the modified synthetic pilot plant solution. The extraction of cobalt and Zn after a single contact was 93 per cent and 70 per cent, respectively, while the Mn concentration in the loaded organic solution was only 0.28 g/L. A proof of principle pilot plant operation was conducted in 2004 and a demonstration pilot plant for final engineering design in 2006 with outstanding performance of the DSX circuit. For the demonstration pilot plant, the overall recovery of cobalt and zinc exceeded 99 per cent with a raffinate containing only 4 mg/L Zn and 1 mg/L Co. The DSX organic system showed no sign of degradation during the pilot plant operation, indicating good chemical stability under the anticipated commercial operating conditions. The DSX circuit will be implemented in the future Boleo processing plant.

Sep 13, 2010

In recent years there have been many changes in mine ownership due to the on-going rationalisation towards larger mining companies. Larger companies inevitably find it hard to manage small mining operations and in many cases smaller mines do not fit corporate resource, production and profit criteria. Smaller companies are more suited to managing these medium or small scale mines and are tendering for the purchase or lease of mines that larger companies wish to dispose of. In addition to these factors there has also been a trend (especially in Western Australia) for mines to continue operating at ever increasing depths. This in turn has led to more mines operating in high stress environments and experiencing damaging seismicity. Assessing the viability of seismically active mines from a takeover or purchase point of view should involve analysing the risk profile of every aspect on mining that could be affected by adverse seismicity. This includes assessing current and alternative mining methods, mine designs, support systems, extraction sequencing, monitoring and blasting. This paper includes discussion on items that need to be assessed when considering the purchase of seismically active mines, with experience gained from some recent studies in Western Australia. In these cases it was apparent that quantification of previous seismic history on itÆs own was a totally inadequate method of assessing minewide seismic risk potential. A more holistic approach is required, taking into account all aspects of relevant data, all the minewide effects of seismic activity and all possible means of mitigating those effects.

Jan 1, 2002

Radioisotope x-ray and neutron techniques of analysis can be used for the determination of a wide range of elements in minerals. The most important applications of these techniques to the mineral industry are for onstream analysis of slurries and solids, and for geological assay.The radioisotope x-ray techniques are the more developed ones and two installations for on-stream analysis are in routine use in mineral processing plants in Australia. Neutron techniques are being developed, and should prove valuable for geological assay of large numbers of mineral samples, for borehole logging, and for specific on-stream analysis when the cost of the equipment is warranted.

Jan 1, 1970

By A K. B Chigwada

Mining organisations grapple with the same problems year after year, wasting incredible amounts of time and money. According to estimates from the International Labour Organization (ILO), over one million work-related deaths occur annually, and hundreds of millions of workers suffer from workplace accidents and occupational exposure to hazardous substances worldwide. Many accident reports cite human failure as a primary cause (Busse and Johnson, 1998). The workers at the Bhopal chemical plant pumped methyl isocyanate into a leaking tank (Morehouse and Subramaniam, 1986). On 3 December 1984, more than 40 tons of methyl isocyanate gas leaked from a pesticide plant in Bhopal, India, immediately killing at least 3800 people and causing significant morbidity and premature death for many thousands more. The company involved in what became the worst industrial accident in history immediately tried to dissociate itself from legal responsibility (Broughton, 2005). Australia is not spared from safety problems either (Lucas, 2022). The ILO Convention 176 (1995) as a response provides that national law should inter alia provide for the supervision of safety and health in mines; the inspection of mines by designated inspectors of the competent authority; the procedures for reporting and investigating of fatal and serious accidents; the compilation and publication of statistics on accidents, occupational diseases and dangerous occurrences; the competent authority to suspend or restrict mining activities on safety and health grounds until conditions giving rise to the suspension are addressed; and worker consultation on matters related to safety and health in mines. This has assisted in getting enough data to define the magnitude of the problem to the mining sector.

Apr 16, 2024

Electro-Flotation Research on Fine Cassiterite

Sep 13, 2010

By J Rutter, D Francois-Bongarcon, M Federov, N Odiar, M Scott

There are two fundamental methods for metalliferous sensing of primary crushed ore available for deployment at operations. These methods can be classed as surface measurement techniques (including XRF, LIBS, NIR, SWIR) or penetrative/semi-penetrative measurement techniques (including PGNAA, PFTNA, GAA, MR). While the individual sensing technologies exploit different physical phenomena to measure metal content, penetrative sensor measurements of grade are often regarded to be superior to surface measurement techniques due to the much larger sampling volume penetrative techniques provide. Surface sensing techniques often utilise simpler, established technologies that have considerable benefits in the speed of analysis, capital costs, ease of deployment, social license to operate and operational safety. This paper investigates whether surface sensing techniques achieve adequate sampling representativity of primary crushed rock mass to provide economic benefit over penetrative sensing technologies for bulk ore sorting applications. The paper details the methodology used to assess whether surface XRF measurements change throughout various stages of comminution, and increased surface exposure, from primary crushed ore (top size of -175mm) to finely crushed product for assay (top size -2mm). The methodology was applied to 2 ore mineralisation styles, across variable metals and grades, to identify any associated opportunities and limitations to surface sensing techniques. The results assist in developing a method to determine if surface sensing and measuring via XRF is an adequate representation of the rock mass for bulk ore sorting applications and identify any associated limitations in particle size distribution, mineralisation or natural deportment strength to guide suitable application of surface sensing techniques.

Nov 10, 2020

This paper covers only the energy uses of natural resources and does not deal with non- energy uses, which in 1975 were of the order of 10 per cent of the total consumption of energy resources. The United Nations `J' Series of Statistics ex- presses each of the various forms of energy in terms of its coal equivalent in metric tonnes and this basis is followed in this paper. One tonne of black coal (referred to as tce) has been taken as the equivalent of the following. 29 X 109 joules or 27.5 X 106 Btu 0.68 tonnes or 4.8 barrels of crude oil 750 cubic metres or 26.5 X 103 cubic feet of natural gas 1 ò5 to 3.3 tonnes of peat or lignite (world average 2.54; Victorian brown coal 3 0) 8055 kWh (at 3.6 X 106 joules or 3412 Btu per kWh at 100% efficiency) 2660 kWh at 33% efficiency of generation 50 grams of uranium present in natural uranium reactors (see note later under nuclear energy) 0.8 grams natural uranium in breeder reactors Nuclear and hydro electricity are expressed as the coal equivalent required to produce, at 33 per cent efficiency, the same amount of electricity. In other words, electricity produced by these sources is converted to its coal equivalent at the rate of 2660 kWh = 1 tonne coal.

Jan 1, 1978

Coal mining ceased at Strongman Mine this year after 70 years of production. Underground mining finished in 2003 and opencast methods began in 1998. During the life of the mine, 8 million tonnes of coal was extracted from two underground mines and 1.2 million tonnes removed through opencast methods. Strongman Mine is within the Grey Coal Fields; various seams have been extracted from the Rewanui Coal Measures. Coal extracted was predominantly of thermal or semi-soft specifications and characterised by low sulphur and low ash.   The area has steep topography, high rainfall (>3000 mm/yr) and is particularly exposed to westerly quarter winds. Strongman 1 and 2 underground mines are located in the steep, narrow valley which leads to the Strongman Opencast at the top of the valley. Subsidence from underground mining combined with spontaneous combustion, has resulted in an underground fire which has had substantial surface effects. Opencast mining in the steep topography resulted in several landslides at the perimeters of the site. These factors, along with water management, topsoil management and erosion control have added to the complexity of rehabilitating the site.   Rehabilitation of the site is well underway, including infrastructure removal, final landform creation and revegetation of the Strongman Opencast footprint (~45 hectares). Some innovative methods of rehabilitation have been trialled. Successful trials such as helicopter-seeding and moss hydro-seeding on highwalls are now routinely used along with traditional revegetation practices. 18 hectares disturbed land has been replanted with 88 000 seedlings, and another 200 000 seedlings are scheduled for planting over the three years. Fire management is an ongoing challenge; however thermal photography shows a steady decrease in hot areas which have been contained by grout curtains.   Mine closure is some time away and will occur after all standards set by Solid Energy and regulatory bodies are achieved.

Jan 1, 2006

By R H. Knight

Uncertainty in prediction and modelling of geological (physical) ore continuity in geometrically complex ore deposits is a key risk factor in mining. Reducing geometric uncertainty of hard-boundary ore/waste contacts and related geological features improves the efficiency of local mineral resource estimation and reserve calculation, mine/stope planning, ore control and in-mine exploration. Detailed underground mapping of serial-level drives provides a continuous record of the characteristics and contact configuration of ore, as well as crucial ore-related geological features that are required to resolve geometrical variability when closely spaced drilling proves inadequate or is cost-prohibitive. The mapping-based approach described in this paper re-establishes the focus on the geology of the orebody by incorporating high-value, detailed geologic mine mapping information. Mapped ore-related configurations and relationships, recorded on a succession of faces or on a series of levels, provide the basis for 3D interpolation and extrapolation of the local geologic continuity of an orebody. Correlative points representing locations of key ore-related geologic features on each face or level are linked by 3D polylines or trajectories forming a coherent geometrical framework. The coherent progression of geometric changes mapped by these trajectories reveals the overall ‘dynamic’ of the geometrical framework, as well as the spatial tendencies of its geological constituents. Distinct sets of ore control trajectories are selected from within the framework and are used in the construction of alternative geological ore continuity models. As mining proceeds, alternative models are evaluated, and are then either refined or rejected. The geometrical framework is used to evaluate theoretical models and practical heuristics, focus exploration targeting and inform and guide all aspects of mine geology in active mines. This approach also lends itself to analysis of global ore continuity in the re-evaluation of mature or abandoned mines. Its use is particularly effective in geometrically complex orebodies such as the West Branch orebody and the orebodies of No 2 mine of the Balmat-Edwards-Pierrepont zinc district, which are used to illustrate the method. CITATION:Knight, R H, 2014. A mapping-based approach to geological continuity prediction using examples from the Balmat-Edwards-Pierrepont Zinc District, St Lawrence County, New York, USA, in Proceedings Ninth International Mining Geology Conference 2014 , pp 65–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

Energy Savings and Technology Comparison Using Small Grinding Media Considering the complexity of minerals, the need for finer grinding is increasing along with the energy cost. However, energy is increasing exponentially when grinding finer with conventional grinding balls. The use of small grinding media represents the best potential to improve energy efficiency. Today, it is possible to use grinding media as small as 1 mm. How do they perform in industrial grinding mills? The use of small grinding media (5 - 12 mm), called Millpebs, in regrind mills proved that finer grinding can be achieved at lower energy consumption. In ball mills, energy savings vary from 10 per cent to 40 per cent compared to 25 mm media. A regrind ball mill with a mix of small grinding media can be as energy efficient as an Isa Mill charged with 2.5 and 3.5 mm beads. In vertical stirred mills, energy savings vary from 30 per cent to 60 per cent. To carry out the same final grind, a vertical stirred mill with Millpebs will consume at least 60 per cent less energy than a ball mill using 25 mm grinding media. More potential savings were identified. To achieve those improvements, some operating conditions must be met: 1) feed size should be less than 250 ¦m; 2) the pulp must be fluid enough; 3) finally, the slurry linear velocity should not be excessive. This paper talks about all those industrial results improvement and operating conditions.

Sep 13, 2010

Development of Grindability Tests Based on Direct Measurement of Energy Nowadays, for the characterisation of the grindability different grindability indices - Bond-work index (Wi), Hardgrove Grindability Index (HGI) or Zeisel specific grindability (Wt) - are used. Generally, the grindability tests are carried out under relatively simplified circumstances, in a special dry batch mill with defined feed size material until prescribed conditions are reached at room temperature. However, in the fine- and ultra fine grinding, which is a frequent task (fly ash, tailings, alumina, etc), a fine material (<50 - 200 ¦m) is usually ground down to the few micrometers. The conventional grindability testing methods and apparatuses (Bond-, Hardgrove-, Zeisel-processes) for their determination, although, are not suitable directly to measure the grindability of such fine materials, since the maximal particle size of the feed material (0.5 - 3 mm) to be tested is much higher. One of the important goals of the research carried out in our Institute was to develop the novel grindability testing methods, which are suitable for the fine and ultra fine grinding, and additionally provide the possibility for the fast determination of the grindability. In order to realise the above aim the conventional Bond- and Hardgrove- mills were modified in order to directly measure the grinding work. In particular, the Hardgrove-mill was equipped with a simple torque-meter (load cell). The Bond-mill was rigged with a digital electric power measurer. The systematic experiments were carried out parallel in both mills using the conventional and the developed methods. Finally the results of both were compared. The measuring results have proved that the Bond-work index can be determined based on the developed methods. The new grindability testing methods were applied successfully in several industrial research tasks for the determination of the specific grinding energy and the Bond-work index. These methods can be also used in the industrial practice for the control of the grinding process.

Sep 13, 2010

Last evening, in Auckland, I heard the Chairman of Heinz US, Dr Tony O'Reilly (who, in addition to Heinz's ownership of our largest food processor, also has substantial personal investments in this country), advocate New Zealand as a 'regional corporate capital'.   Why would someone like Dr O'Reilly hold that view? No doubt, as one of Ireland's great rugby players of the 50s and 60s, he admires at least one thing that we do very well (confirmed again in Dublin over the past weekend). But that's not sufficient to support such a view.   He cited many reasons for preferring New Zealand over, say, Sydney, Australia, calling this 'the most rational in which to locate [an] international headquarters', including û +         we have no capital gains tax; +         a more 'pro-business environment'; +         a 'first class' legal and banking system; and +         a 'simple political system'.   I can find no better 'text for today's address.

Jan 1, 1997

By E Wargem

The optimum mining of an orebody in an underground mining operation is fundamental to the mine’s ability to operate both sustainably and efficiently. The effective mining of an open stope or a cave is largely reliant on the recovery of the initial void created by conventional drilling and blasting. These initial voids are known by various names such as a Longhole Rise, Slot or Winze and can be mined either as a downhole or as an uphole. Regardless of the underground mining method, the process of the design and implementation of this initial void is largely uniform across many operations with various patterns of slot or winze designs used across these different operations. Diligent design, implementation and review strategies in drilling and blasting of these will facilitate cost-effective mining with minimal disruption to mine schedules and production targets. When an operation struggles in opening the initial void in underground mine blasting, it has a negative impact on productivity, mineral recovery, and the overall economics of mining. Near field blast vibration monitoring is a vital tool to use in analysing slot blasts and will provide additional feedback into the reconciliation part of the drill and blast process. It is one that is often overlooked in the mining industry in many operations due to many factors such as lack of skilled personnel, or a lack of required resources. The data obtained from near field blast vibration monitoring can be used to provide additional feedback into blast reviews and help in any drill and blast optimisation projects. This paper highlights key aspects of underground drill and blast reviews and the use of near field blast vibration monitoring for post blast analysis and shares learnings from various projects that the authors have been involved in within Australia and abroad.

Mar 29, 2023

By G J. Lyman, F S. Bourgeois

As the prices of metals slide, financial control of mineral processing operations becomes more and more important. Control of a mineral processing operation implies measurement of grades, recoveries and losses, with every effort being made to recover more product from the same feed. Shareholders become more concerned with the transparency of the operations and the corporate governance.There is only one way to achieve this and this is by sampling and making good use of the results of that sampling. Sampling systems that provide only 'rough' figures are not good enough. Similarly, a competitive position in the marketplace demands close control of product quality. Maximisation of product output demands that the product just meet the specification so that product yield is maximised. Decisions based on precise sampling results carry less risk that those based on imprecise results.This paper reports some recent advances in sampling theory that permit full quantification of sampling distributions, not just the sampling variance as has been possible in the past. These advances can be used together with simulation methods to tie down sampling precisions and develop calculations that quantify decision making risk when using the sampling results. A number of examples illustrate the use of the new advances and a final example indicates the development of risk analysis curves in the coupling of sampling precision to sale of a commodity.CITATION:Lyman, G J and Bourgeois, F S, 2015. Sampling, corporate governance and risk analysis, in Proceedings MetPlant 2015, pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

A good deal of experimental work has been done from time to time on the application of compressed air to the elevation of wet pulp. On account of the flat nature of most of our mill sites elevation of the pulp has to be provided for, and the various methods in vogue show considerable loss of time, in the replaceing of wearing parts. During the last two years the writer has carried out a great many experiments with a view of devising an elevator that will give continuous work with a minimum of wear.The results do not show a high efficiency for the power employed, but the lift is continuous in operation, very cheaply installed, and possesses no wearing parts. The lift was tried working in a bore hole of 8 in. diameter, but in many cases it is more convenient to sink a small well for the purpose. The result to date showed that the most efficiency was obtained when the depth of the wellwas not less than the height of the lift required. The pressure of air required in pounds per square inch was (approximately) half the number of feet to be lifted.In the majority of cases the lift required varied between 20 ft. and 50 ft. and the air pressure required between 10 lbs. and 25 lhs. per square inch. In most existing installations the air compressors in use were delivering air to the receivers at about four times that pressure, and when air so compressed was expanded to perform its work at a reduced pressure, it was apparent that the power exerted in origInally compressing the air above the working pressure required at the lift was absolutely lost.

Jan 1, 1901