Search Documents

By E Jak, G Khartcyzov, M Shevchenko

The increasing complexity of ore resources and recycled materials in the feed of pyrometallurgical processes present a technical challenge to the metallurgical engineers working on maximising the recovery of the valuable elements and minimising the environmental impact of the processes. To address this challenge, the availability of computational tools that can predict the mass and energy balance in complex systems is required. Then the accurate description of phase equilibria in the complex multicomponent systems describing the chemistry of the pyrometallurgical processes becomes critical for the correct implementation of the indicated tools and facing the outlined industrial challenges. In the present study the distribution of selected elements (Pb, Zn, Fe, As, Sn, Sb, Bi and Ni) between oxide liquid and metal in the ‘CuO0.5’-CaO-AlO1.5 system in equilibrium with Cu metal at 1400°C (liquidus of CaAl2O4) was experimentally studied using the equilibration and quenching technique followed by the electron probe X-ray microanalysis of the resulted samples. The study covered a wide range of effective p(O2) over the system from 10-11 to 10-3.5 (corresponding to formation of immiscible CuO0.5-rich slag). To avoid loss of volatile elements (Pb, Zn, As, Sn, Sb and Bi), a correlation between ‘CuO0.5’ in oxide liquid and p(O2) in open system was obtained first, followed by studying the volatile elements distribution in closed conditions (Al2O3 crucible sealed in SiO2 ampoule), where ‘CuO0.5’ concentration was used as a marker to evaluate the effective p(O2) over the system. The experimental results were then used for the optimisation of the thermodynamic model parameters of the system as part of the integrated experimental and self-consisting thermodynamic modelling research program of phase equilibria in the Cu-Pb-Zn-Fe-Ca-Si-Al-Mg-O-S-(As, Sn, Sb, Bi, Ag, Au, Ni, Cr, Co and Na) gas/oxide liquid/matte/speiss/metal/solids system.

Jun 19, 2024

The expansion of hydrometallurgical operations, declining ore grades and upwardly spiralling production increases the demand for fresh and recycled water with low levels of contaminants. The minerals industry is also increasingly being forced both by regulatory and cost pressures to reduce the amount of liquid waste they produce. This requires a strong focus on waste reduction by recycling, regeneration and reuse. However, these measures are often not enough in arid countries for a forward progress and expansion of their mining activities.   It is often the case that in the arid and semi-arid countries the only available water is either sea water or underground (brackish to hypersaline) saline waters. Brackish waters can be desalted at a reasonable cost but the desalination of highly saline waters is challenging and expensive.   There are emerging reports that sea water and in some cases hypersaline underground waters are now used by various mining industries as process water. This study explores the possibility of the use of sea water in various mineral processing and hydrometallurgical processes and briefly discusses the benefits and problems related to the use of saline waters at the mine and mill site. Several cases studies and preliminary laboratory test results are presented.

Jun 1, 2010

By D Brouwer, P Wild, B Belle

Due to the steep geo-thermal gradient in Bowen Basin area, as underground coalmines reach increased depths of extraction, the Bulk Air Cooling (BAC) requirements will increase as opposed to cooling the workplace using the ventilation means alone. One such mine has already been using a 4 MW surface BAC plant for the last six years to manage the working temperatures with reduced cooling efficiency as the mine expands. Due to the horizontal nature of the longwall mine layout, distances from the working face to intake shafts are rapidly expanding to over 6 km as opposed to the vertical mine layout of a hard rock mine. To improve the positional cooling efficiency, reduced panel pressure differentials, improved rib emission gas management, and intake dust management, small diameter intake shafts were located on the inbye end of production panels and halfway up the development panels with localised mobile small BAC plants. This paper summarises the results of extensive underground data of this innovative cooling concept for development and retreating longwall face heat management compared to a larger remote BAC plant.CITATION:Belle, B, Brouwer, D and Wild, P, 2017. The use of mid-panel ventilation shafts to improve positional cooling efficiency in a Bowen Basin longwall mine – a case study, in Proceedings Australian Mine Vent Conference 2017, pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By I Gray

While in some cases it is vitally important to measure the virgin stress in rock prior to tunnelling there are a number of cases where such stress measurement is really not required. The concept of having to have a number to put in a numerical model representing a continuum is often quite inappropriate. This paper discusses the cases when virgin stress measurement is required and the most appropriate means to measure it. The techniques discussed cover all of the overcoring systems, hydrofracture and borehole breakout measurements. It also covers the use of rock surface stress measurement, which is easy to perform and should be used to check for changing stress conditions. Unfortunately this technique has been ignored in recent times because engineers are addicted to numerical models requiring far field stresses rather than measuring the real values that exist where they matter – at the tunnel wall. A case is presented in which the measurement of surface stress in a tunnel boring machine tunnel enabled the far field stress to be determined in what must be the world’s largest overcore.CITATION:Gray, I, 2014. The measurement of rock stress for tunnelling, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 153–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

In the UK during the 1990s the energy companies had developed a policy of æDash for GasÆ, building large natural gas power stations to produce more than 30 per cent of the UKÆs electricity demand. The price of imported thermal coal was dropping and the electricity generators were putting pressure on the UK coal producers to produce coal at a reduced cost. Imported coal from Columbia, South Africa, America and Australasia had increased their market share in thermal coal sales to over 50 per cent of a 55 Mtpa market. The pressure on the UK coal industry to reduce costs and improve productivity levels from an ever decreasing resource was high. Companies were benchmarking their operations on the imported coal producers and had to realign their organisations, productivity levels and costs to world best practice, not just technically, but in world class organisational management techniques.

Jan 1, 2005

By J Knoblauch, D, P J. J Strobos, C Foggo

The Sally Malay Project is located 120 km north of Halls Creek in the eastern Kimberley region. Since commissioning, ongoing improvements on the plant have resulted in recoveries now greatly exceeding the initial design targets. The continual optimisation endeavours of the Sally Malay metallurgy department included an automation project that was done in close collaboration with Mintek. In this team effort, several problem areas were addressed and the FloatStar advance control system was successfully commissioned to stabilise and optimise the flotation circuit. The remote location of the Kimberley Nickel Mines operation, fly-in, fly-out roster and the current mining boom makes the acquisition of experienced flotation staff difficult. The implementation of an automated flotation control system reduces this burden and contributes to the training of inexperienced staff. This paper illustrates not only the process control improvements achieved as a result of the installation of the FloatStarÖ advanced control system, but also how it has assisted operational personnel with their understanding of the process.

Jan 1, 2006

By J Pan, C M. Tang, D Q. Zhu, C C. Yang, S W. Li, Z Q. Guo

The short process of electric furnace steelmaking with direct reduction iron (DRI) as raw material is an important process for smelting high-quality and special steels. In order to prepare high-quality DRI, the pellets with basicity of natural basicity and 0.4 were prepared from magnetite concentrate (MR=0.09, MR=0.4) and hematite concentrate (HR=0.02, HR=0.4). Based on the HYL method, the gas-based direct reduction experiments were conducted under the condition of rich hydrogen (H2/CO = 2.6). The reduction index (RI), reduction swelling (RSI), cold compressive strength (CCS), and phase changes of the pellets were systematically studied. The results show that the RI of four kinds of pellets is greater than four in the temperature range of 800~950°C. For the magnetite pellets, at a fixed reduction temperature, the RSI increases and then gradually decreases, reaching a peak between 50 per cent and 80 per cent. Moreover, the RSI enhances with the increase of the reduction temperature. In general, the RI, RSI, and reduced CCS of the MR=0.09 pellets are better than those of the MR=0.4 pellets. For the hematite pellets, the maximum RSI decreases from 23 per cent to 17 per cent during hydrogen-rich reduction, while the compressive strength increases from 500 to 1070 Nꞏpellet-1. The main reason is that the glass phase generated by the increase of basicity adheres to the surface of hematite grains, hindering the contact between reducing gas and particles. As a result, the apparent activation energy is reduced, which is not conducive to the reduction process. In addition, the glassy phase attached to the hematite reduces the migration rate of Fe2+/Fe3+, resulting in a difference in the reduction expansion rate of hematite in the inner and outer layers of the pellet. Thus, concentric cracks are formed inside the pellets, the RSI increases and reduced CCS decreases.

Sep 18, 2023

The N3500 orebody is the northern continuation of the 3500 orebody at Xstrata Copper's Enterprise Mine and occurs at a depth of 1.3 to 1.8 km. At the nearby S3500 orebody, extreme deformation was observed in access drives where there was a high number of bedding planes per metre combined with either graphite or talc infill. The observed failure mechanism was largely controlled by the geometry of the inclined bedding submitted to high horizontal stresses. Due to the anisotropic strength and deformation behaviour of the shale rock mass, traditional isotropic methods of geomechanical property estimation based upon GSI are not appropriate. A numerical modelling approach, based upon the distinct element codes UDEC (2D) and 3DEC (3D), has been developed to accurately simulate the failure mechanisms and deformation observed in the initial infrastructure surrounding the N3500 orebody.

Nov 25, 2010

By C C. Souza, S C. Amarante, A C. Arauj

All major companies now producing iron ore in Brazil currently employ or are planning to employ some sort of concentration method to upgrade their fine sized products (sinter feed fines and pellet feed fines). The criteria for the selection of the most suitable concentration method for each application include a series of parameters; the most important among them being related to ore mineralogy. This paper reviews the concentration operations currently employed in Brazil and shows how ore mineralogy plays a fundamental role in the selection of a given method. Examples involving gravity concentration (jigs and spirals), magnetic separation (Rare Earth wet drums, ferrous wheel, and Jones type magnetic separators) and flotation (especially column flotation) are discussed. Fundamentally important for the selection of a concentration method is the mineralogy of iron-bearing minerals and gangue minerals presented to the feed to the concentration unit operation. For instance, the presence of liberated quartz as the major gangue mineral for a pellet feed size stream generally indicates that flotation will be the best selection for the concentration of that stream. However, even if magnetite is present only in the form of crystal relicts within hematite grains, it may lead to the selection of either magnetic separation alone or a combination of magnetic separation and flotation for concentrating such material. Presence of gibbsite and/or kaolinite as the major phase containing alumina will also affect the selection of the concentration method in all cases. Again for the case of pellet feed size streams, kaolinite does not interfere with flotation whereas gibbsite tends to contaminate flotation concentrate (pellet feed fines) as it is depressed together with iron oxides and hydroxides during the reverse cationic flotation process.

Jan 1, 2002

By C E. Davies

At present the source of virgin iron for steel produced in New Zealand is titanomagnetite extracted from titaniferous beachsands. Some of these beachsand deposits contain extractable quantities of ilmenite as well as titanomagnetite and both minerals represent challenging sources of vanadium and titanium products in addition to iron. This study looks at some theoretical aspects of smelting these ores directly with coal rather than with electric power, and takes into consideration the properties of the raw materials, the thermodynamics of possible process routes and the background of the economics involved.

Jan 1, 1980

By P Duplancic and C R Lilley, R Hudson, D Beck

For deep block and panel caving mines, undercut or extraction level instability can have as much impact on overall recovery as underbreak or the premature ingress of waste. If the area of the mine affected by excessive convergence is small, recovery is usually possible. However, there are several examples of entire blocks that were abandoned prematurely due to footprint collapse. Clearly, such global instability has a major impact on recovery and must be avoided – this is one of the essential tasks for the design team.The design problem is complex. The planning engineer must ensure that the footprint has sufficient capacity to withstand the maturing loads in the cave, accounting for the effects of stress path, geological structures and the rock mass conditions. These are often uncertain and only sometimes quantified.The demand on the footprint will also be influenced by decisions and actions taken during production, especially related to draw, which can worsen a developing problem. Perhaps most importantly, the design decisions that favour stability and lead to lower deformation also negatively impact on idealised cave flow. Many engineers aim to minimise the size of extraction level pillars, to improve theoretical future resource recovery but in fact this can reduce recovery if widespread deformation ensues due to the undersized pillars.In 2014, PT Freeport Indonesia undertook detailed numerical analysis to quantify the effects of variability in rock mass conditions and geological structure on overall footprint performance. The analysis accounted for a range of stress paths and maturing cave loading scenarios sourced from a calibrated whole-of-cave deformation-flow model. The intent was to replicate some of the diversity and distribution of pillar deformation outcomes that may be seen in practice at Freeport.The discontinuum finite element analysis was able to replicate damage localisation around persistent structures, a realistic distribution of drive deformation and show how small areas of instability can evolve into major problems if poorly managed. The limits of pillar size and ground support as solutions to a number of different instability problems was also investigated, showing that pillar size alone was not a sufficient remedy for all adverse circumstances.In this paper, we describe the workflow for numerical analysis of footprint deformation. We discuss the compromises and considerations for balancing the sometimes competing needs for efficient extraction levels pillars, ground support and prudent draw strategy.CITATION:Beck, D, Hudson, R, Wilson, A D, Duplancic, P and Lilley, C R, 2016. An investigation of factors affecting the long-term reliability of extraction level pillars in deep block and panel caves, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 295–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M Haydon

How do you portray a large structurally and stratigraphically complex deposit to return a meaningful resource estimation, and produce a geological model that is useable for planning on a daily basis? The George Fisher Mine is located 22 km north of Mount Isa and forms part of XstrataÆs Zinc Group operations. It is currently a major producer of zinc, lead and silver in the region with an estimated total resource for all categories of 127 Mt at 100g/t Ag, 5.3 per cent Pb and 9.2 per cent Zn (June 2005). Production in 2005 totalled 2 647 492 wet tonnes for 317 699 kg Ag, 140 317 tonnes Pb and 230 331 tonnes Zn from underground operations. George Fisher (GF) consists of two deposits that are structurally complex on a mine scale, George Fisher North (GFN) and George Fisher South (GFS). Regional faulting has resulted in a 2 km long package of variably pyritic shale and siltstone that separates the deposits. This paper looks specifically at GFN. Distinct correlations exist between the two deposits based on stratigraphic matches; however, orebody characteristics, geometry and fault architectures differ significantly between the two. The deposits consist of multiple, sedimentary-hosted, stratiform orebodies from 2 to 25 m wide, separated by waste intervals of variable width. Each ore-waste interval is modelled as an individual geological domain. Structurally, George Fisher North (GFN) contains a series of major late-stage NE faults with dextral offset(s) of up to 130 m. Further complexity is added by NS, NW and NNE striking fault orientations that can produce either a loss or repeat of stratigraphy, local drag folding, orebody attenuation and block rotation. Due to this structural complexity and orebody offsets, domains at GFN are further divided into fault blocks (FB). The GFN model comprises eight FBs over a strike length of 1 km, all of which are modelled independently. As drilling progresses and additional resources are converted, further FBs will be added at major fault offsets to accommodate orebody and model expansion. This will be in addition to what is already a large and time-consuming data set to manage and update. For example, each FB has 18 domains each with two constraining wireframes (hanging wall and footwall). Each wireframe has several sets of point data depending on the type of data available, ie diamond drilling, mapping or interpretation points. This equates to over 1100 separate files to manage. Additional wireframes and files are also required for major structures, daily planning requirements and block model runs. In total some 1500 files are managed, updated and maintained for GFN alone. The ongoing need to expand as a business and optimise production in the current economic climate where there is a global demand for metal has led to an increase in production at GF. This has resulted in a rapidly growing data set and highlights the importance of practical and efficient modelling to achieve a meaningful resource estimate. This paper focuses on the geological modelling, modelling approaches and techniques employed for the GFN deposit.

Jan 1, 2006

By S Jokanovic, J L. Mauk

The Taharoa ironsand deposit covers approximately 16 km2 and is located 144 km south of Auckland on the west coast of the North Island, New Zealand. The heavy mineral-rich sands predominantly contain titanomagnetite, ilmenite and hematite, along with lesser amounts of amphiboles, pyroxenes, and feldspars. Throughout the Taharoa mine site 142 samples were collected of which approximately 25 samples were used in mineralogical analyses of the magnetic, heavy non-magnetic and light non-magnetic fractions. Mineralogical and petrographic analyses confirmed the high abundance of homogeneous magnetite and magnetite containing ilmenite exsolution lamellae which have oxidised to hematite. A limited number of sand samples were collected from Taranaki beaches. Petrography reveals exsolution textures of magnetite and ilmenite (now hematite), and homogenous magnetite grains similar to those observed at Taharoa. Petrographic analyses from previous research projects were also closely investigated in order to make mineralogical comparisons from along the west coast of the North Island and with other potential source areas. The origin of detrital magnetite grains along the west coast of the North Island is generally presumed to be the eroded volcanic cones of the Egmont volcanoes and active and dormant volcanoes of the central North Island. Electron microprobe analyses of magnetite grains from Taranaki beach samples reveal TiO2 values of between 1.5 and 120 per cent. MgO and A12O3 contents also vary widely from 0.75 to 6.5 per cent. This large variability may reflect different volcanic eruptions, the presence of exsolution textures or alternative source areas for these magnetite grains. Geochemical results from the Taharoa mine site correlate with the Taranaki beach samples suggesting that the Egmont volcanoes are certainly one source area. Variability in XRF results, especially Fe and Ti contents (9.04 - 59.22 and 0.80 - 4.64 respectively), from the magnetic and heavy non-magnetic fractions likely reflect the detrital nature of this deposit.

Jan 1, 2003

By G Corbett

Epithermal Au-Ag deposits form in the upper 1 km of the crust and are therefore best preserved in the less eroded Pacific rim arcs, although also recognised elsewhere. Two profoundly different ore fluid types give rise to low and high-sulfidation styles apparent as variations in ore and gangue mineralogy as well as characteristic zoned wall rock alteration. Low sulfidation epithermal Au deposits are derived from near neutral composite magmatic-meteoric fluids and divided into a group with a stronger intrusion association within arcs grading in time and space from: quartz-sulfide Au + Cu, to carbonate-base metal Au, and the epithermal quartz Au + Ag, whereas in strongly extensional settings the influx of meteoric waters promotes the development of chalcedony-ginguro banded Au-Ag epithermal veins. In the presence of continental crust particularly in Latin America polymetallic Ag-Au veins represent a Ag-rich equivalent of carbonate-base metal Au and passes upwards to chalcedony-ginguro Au-Ag style. By contrast high-sulfidation epithermal deposits are deposited from an acidic magmatic fluid which provided characteristic hydrothermal alteration by reaction with wall rocks grading outwards as mineral assemblages dominated by: vughy silica, alunite, pyrophyllite-diaspore, dickite-kaolin and then illite-smectite neutral clays. Au mineralisation is commonly refractory with enargite deposited dominantly later within the silica zone.Exploration for epithermal Au deposits benefits from an understanding of the controls to mineralisation which commonly give rise to the development of ore shoots with widest and highest Au grade ore zones. In low-sulfidation systems a combination of competent host rocks, dilatant structures, higher grade styles of mineralisation and efficient mechanism of Au deposition, contribute towards ore shoot formation. High-sulfidation epithermal Au systems occur in permeable volcanic and breccia host rocks which are linked by major structures to the magmatic source.CITATION:Corbett, G, 2013. Pacific Rim epithermal Au-Ag, in Proceedings World Gold 2013 , pp 5-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By P Donecker

Like all chains, iron ore values chains are only as strong as their weakest link, which in ore processing is often the humble chute. While mechanically the simplest element in the iron ore flow sheet, chutes are often the most problematic and regularly the major cause of unscheduled downtime. Chute designs have remained static for decades, despite the extra demands being placed on them by grade reduction, which impacts chutes in three ways viz: 1. Higher volumetric rates as infeed increases to meet production targets. 2. Higher moisture content as mining goes below water table. 3. Stickier properties as the dilution phase is often clay based. While there is no shortage of ideas and the geometry options are infinite, the fact is that chute design has not kept pace with grade decline and has remained essentially unchanged. One reason cited for this lack of innovation is the difficulty evaluating and de-risking designs. While the power of computers running Discrete Element Method (DEM) models has advanced, the models themselves still need to be ‘calibrated’ with the dynamic properties of the ore. Flow properties commonly measured for bin design are useful for static situations only and were never intended to predict dynamic behaviour as in chutes, a critical qualification lost in the mists of time. So while they always produce a colourful and reassuring animation, DEM models informed by static ore properties often result in wildly inaccurate real world predictions. Responding to this low success rate, many operators are now utilising physical modelling to help reduce risk and avoid the consequences of having an underperforming chute in their value chain. Physical testing, in a dimensionless scale-down of the proposed system (bulk material and chute geometry), addresses the shortcoming of mathematical models designs and when used in combination with DEM is the best option. In the ideal world, the focus of chute modelling should be innovative design concepts aimed at addressing future needs, however in reality the focus is nearly always on modifications to installed chutes that are underperforming even today. This situation can be traced back to design procedures which if informed at all, are based static ore properties. As an industry, we need to break this cycle and become more proactive, which means addressing flaws in the current design process. In 30 years of providing modelling support to the industry, I have looking at hundreds of underperforming chutes in the iron ore industry. This practical experience has led to a unique and unbiased perspective on chute design and their performance in the real world. The knowledge presented in this paper can not only be used to help avoid baked-in problems now, but also help guide and evaluate designs so we can deal with the challenges of our low-grade future.

Sep 18, 2023

By R Razanatsimba, A Galli

A mining company has entered into contractual commitments to supply certain quantities of its product to clients in each time period. Failure to fulfil its obligations would damage its reputation as a reliable supplier. The planned production would normally be sufficient unless major problems such as highwall failures, roof falls, natural disaster, or strikes that interrupt production or delays in obtaining environmental permits, occur. To overcome these difficulties, the company may be able to obtain more of the commodity: from its strategic stockpile (if there is sufficient there); by buying it on the spot market; or for some commodities such as gold and uranium, by leasing it. Two sources of uncertainty, the spot price of the commodity and the occurrence of serious incidents that interrupt production, are considered. For simplicity it is assumed that the commodity price follows a geometric Brownian motion, that productions incidents have a binomial distribution, that they are independent from one time period to another and that they do not affect prices. A branching tree structure is used to model the joint evolution of prices and production incidents. The aim of this research project was to evaluate the companyÆs options for fulfilling its contractual commitments. When evaluating these options, multi-stage stochastic programming with recourse was used to solve this problem because in addition to providing the dollar value of the project, it gives decision-makers the æroadmapÆ to reach the optimal value. That is, how much material should be bought/sold on the spot market, how much to add to/subtract from the stockpile, how much to lease and in the worst case what the shortfall would be, for each time period as a function of the current spot price and breakdown status. A case-study over a five-year period is used to illustrate the proposed procedure. In this study the production would be sufficient to cover the companyÆs contractual commitments unless production incidents occur. Focus is on evaluating the impact of the quantity initially in the stockpile on the value of the project when the commodity market is tight, that is, when only small quantities can be bought on the spot market or by leasing.

Sep 26, 2011

The Phoenix mine on the Mararoa Reef at Norseman, Western Australia, provides an outstanding: AUstralian instance of the recurrence of payable ore beneath the bottom of an abandoned mine, and an interesting and instructive example of the development ofideas with regard to ore recurrence in a particular district. The Mararoa Reef is the most productive of several hypothermal goldquartz vains in pre-Cambrian basic volc81olics which strike northsouth and dip on the average, 45 degrees east. The Phoenix minewas abandoned at 500 ft. vertical depth after producing 342,000 tons of 9.9 dwt. recovery grade (equivalent to nearly half of the total production of the Norseman field) from a 2,500 ft.. long, horizontally disposed oreshoot, which is reported to have had an ore outcrop only 30 ft. in length.Interest in the field was revived in 1933, and by 1941 new ore mined and developed on the Mararoa Reef by Central Norseman Gold Corporation N.L. amounted to approximately 700,000 tons of 6.7 dwt. recovery grade. In the same period another oreshoot of similar size and grade was developed by Norseman Gold Mines N.L., south of the old Mararoa company's site. As shown by the plans, the ore occurs in discontinuous shoots. The intervening area of shear is poor in quartz as well as in gold. Geological work on behalf of Western Mining Corporation Ltd., and Central Norseman Gold Corporation N.L. has been in progress in the mine and in the field more or less continuously from 1913 to 1941 and again since 1946. This paper describes the successive advances in the understanding of the exploratory problem up to late 1941, to which several investigators have contributed. It is published by permission of the Board of Directors of Central Norseman Gold Corporation N.L., owners and operators of the Phoenix and other mines.Development of the Prospect.In 1933 Western Mining Corporation acquired an option over the Phoenix property and adjacent leases. H. E. McKinstryl visited the mine and recognised that the ore occurred primarily on the flatly dipping sections of the vein, as distinct from the steeply dippingsections, in a wide shear zone with reverse movement. Many of the flatly dipping fractures were seen to exhibit tension phenomena and to link one shear plane to the next below on the footwall side. The flat links carried much more quartz than the steeper shears.Later, H. J. C. Conolly, assisted by J. D. Campbell, examined the prospect and by contouring the vein with reference to an inclined...

Jan 1, 1950

By A Suwandhi, H Utama

PT. Indo Muro Kencana (PT.IMK) is a gold mine that is located in Central Kalimantan, Indonesia. Drilling and blasting activity is applied in order to support mining production. Drilling and Blasting (D&B) planning is conducted by its engineers. A drilling and blasting contractor conducts drilling and blasting activity. The objective of this paper is to evaluate the implementation of the scaled depth of burial (Chiappetta and Treleven, 1997) in explosive charging sheet application to increase blast efficiency. The function of the scaled depth of burial is to maintain stemming height above explosive charge in order to prevent the ‘over energy’ condition, to reduce the excessive fly rock possibility, to maintain rock fragmentation (digger’s productivity) and to increase blast efficiency. The focus of this paper is to implement the scaled depth of burial as a reference in D&B planning and practice, especially in designing stemming height. The purpose of this paper is to validate that the scaled depth of burial can be used as an engineering tool in D&B practice in PT.IMK. However, scaled depth of burial cannot applied as an engineering tool to determine stemming height above explosive charge for trim blastholes and secondary blasting area. In general, the implementation of the scaled depth of burial in PT.IMK is applicable for production blastholes (ore and waste blasting). In conclusion, it is clear that scaled depth of burial can be used as an engineering tool to create explosive charging sheet and also to increase blast efficiency (ore and waste blasting) in PT.IMK.

Jun 22, 2022

By M Quinteiro, Å Sundqvist

What is special about being a female mine manager? We do not believe that the challenge is greater for women in managing a mine compared to managerial positions in other male-dominated businesses. The challenge lies in the fact that it is a male-dominated business. Being a leader belonging to a minority creates a situation where competence not only lies in having technical knowledge or general leadership characteristics, but also in acquiring an understanding of the male norm and being able to behave and communicate effectively in the organisation.In order to move towards a better gender balance at senior levels it is important to set measurable objectives on desirable proportions between women and men at management levels within the company. Focus and action are required to achieve this goal. At LKAB, the current target is to reach 25 per cent women in the total workforce by 2020. To date, LKAB has reached 19.4 per cent women in the total workforce, and the number of women in management positions is 19.9 per cent.It is of vital importance to create a non-discriminating working environment to achieve equal opportunities at the workplace, to be able to use the whole workforce as a resource for recruitment of professionals and managers, thereby improving decision-making, productivity, efficiency and profitability.Women as mine managers is not a utopia, but rather an effect of long-term investments in actions that result in equal opportunities for all employees.CITATION:Quinteiro, M and Sundqvist, Å, 2016. Women as mine managers – a utopia?, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016) , pp 43–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By P Moswate, D Phillpotts, S M. Mantsho, P Strobos

A challenge on many industrial flotation circuits is controlling concentrate mineral grades using measurements that are provided infrequently. The mineral grades in concentrate streams are a critical performance indicator in any industrial flotation circuit. Failure to achieve concentrate mineral grade targets has significant financial consequences on a flotation operation. A violation of gangue mineral grade limits by the concentrator may also result in significant penalties.Online grade analysers which can provide reliable real time grade measurements are essential for effective grade optimisation. The Blue Cube MQi analyser (by Blue Cube Systems) has recently come to prominence for its ability to rapidly determine mineral concentrate grades online and has the benefit of operating in-stream. This has provided excellent insight into the actual process dynamics in the flotation circuit, and hence enabled real-time control and optimisation of concentrate mineral grades.MintekÆs Measurement and Control division, specialising in advanced control solutions for mineral and metallurgical industries, has had the opportunity to link the FloatStar Grade-Recovery Optimiser to the measurements provided by the Blue Cube system at the BCL nickel concentrator plant in Botswana. The project focused on stabilising the final concentrate grade while ensuring the final tailings are minimised, resulting in an improved nickel recovery. This site already had the FloatStar Grade-Recovery Optimiser for several years, but the original grade measurement device was unreliable and ultimately failed. The system was reactivated once the Blue Cube system was installed, replacing the old analyser. The positive results show the advantages of combining reliable real time measurements with an advanced process control system.CITATION:Mantsho, S M, Moswate, P, Strobos, P and Phillpotts, D, 2013. The implementation of floatstar grade-recovery optimisation control solutions using Blue Cube Online grade analysers on industrial flotation circuits, in Proceedings MetPlant 2013 , pp 575-582 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013