Search Documents

By L Snyman, S Webster and J Samosir

Northparkes is located 27 km north of the township of Parkes in central New South Wales, Australia. The operations consist of underground block cave mines and an ore processing plant, which produces high-grade copper and gold concentrate. Production is currently sourced from the E48 Lift 1 block cave mine and open cut stockpiles. Mining commenced at Northparkes in 1994 as an open cut operation. Underground block cave mining began in 1997. Northparkes was the first mine in Australia to use the highly efficient block cave mining method, which relies on gravity and natural rock stresses to fragment and recover the ore.The E48 extraction level is located approximately 581 m below surface and consists of ten extraction drives and 214 drawpoints. Several stress measurements carried out at various levels in both E26 and E48 indicated a low underground regional stress environment and a low to moderate stress state in the E48 orebody. The E48 block used a post undercut strategy that was initiated in 2009, with production commencing in September 2010 and cave-through to the surface occurring approximately four months later in January 2011. Changes to the cut-off grade and fixed prices meant that Northparkes was able to develop an additional two drives to the north of the existing cave and one additional drive to the south. Modelling of the cavability of the additional drives indicated that the cave would not readily propagate to sufficient height of draw to mobilise the ore and tended to arch over to the existing cave shape. Based on modelling and a desire to reduce the risk of the project, preconditioning was adopted. Along with the requirement of safely hydrofracturing an active cave, a measure of the success of the preconditioning was desired. Few block cave operations have developed extension drives adjacent to existing caves.This paper summarises the lessons learnt from the development of this extension project, with a specific focus on ground control and monitoring.CITATION:Snyman, L, Webster, S and Samosir, J, 2016. E48 cave extension at Northparkes, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 111–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

In this, the centennial year of The Institute, it is appropriate that the history of the Institute in New Zealand be recorded. I am indebted to John Dew, compiler of the centenary publication æMining People A Century - Highlights of the First Hundred Years of The AusIMM 1893 - 1993Æ, for many of the early historical references in this paper. In July 1892 the Amalgamated Mining Managers' Association of Australasia held its annual conference in Ballarat, Victoria, Australia, when it was suggested by the delegate from Broken Hill that the time had arrived for the establishment of an Australasian Institute of Mining Engineers. Resulting from this meeting at Ballarat, a Provisional Committee was formed at Broken Hill with the object of forming The Australasian Institute of Mining Engineers having the following objectives. To promote the arts and sciences connected with the economic production of the useful minerals and metals, the welfare of those employed in those industries by means of meetings for social intercourse, and the reading and discussion of professional papers with the circulation by means of publications amongst its members and associates the information thus obtained.

Jan 1, 1993

Newcrest Mining Limited (NML) owns and manages the Ridgeway Gold Mine (RGM) located outside Orange in the state of New South Wales. RGM is a new underground sublevel caving (SLC) operation that is ramping up production to 4 Mtpa. The success of the SLC method at RGM is strongly influenced by production drill and blast practices. Distinguishing features of the Ridgeway SLC operation include choke blasting against broken rock, drawpoint brow preservation, loading of blastholes with different in-hole bulk emulsion densities, precharging of production rings and routine drawpoint fragmentation assessment. These areas are described in the context of RGMÆs required blasting objectives, production drilling and charging activities and innovative practices.

Jan 1, 2002

By P Rowe

New Zealand Steel's Taharoa titano-magnetite mine, south of Auckland, set two national load records when it transported around 2000 t of mining equipment three kilometres overland on time, under budget and without safety incident. It was the first time in New Zealand that four platform trailers were assembled end-to-end to transport a load. It was also the first time that a single load of 1000 t was transported on platform trailers. The need for the relocation of all equipment was realized five years ago. It took two years of planning and specialist advice to relocate the mine's 250 t dredge, 500 t surge bin, 1000 t concentrator plant and ancillary equipment from the Southern Mining Region across a specially designed haul road to the Central Mining Region. The project was carried out during a six-week shutdown in early 2001. Two dry docks were constructed, one at each end of the relocation route. The equipment was floated into a dismantling pond that was interconnected with the dry dock in the Southern Region. Through pumping, the water levels were controlled to allow transfer of the separated units from the dismantling pond into the dry dock. Once drained, sets of self-elevating platform trailers were used to transport the main units, one at a time, between the dry docks. Five prime movers were used to pull the loads. At the receiving end, the units were off-loaded in a dry dock interlinked with ,the first mining pond. The equipment was relocated because the reserves in the Southern Mining Region were mined out. A natural watercourse û the Wainui Stream û defines the northern boundary of the Southern Region and the objective became to relocate the mining plant to the other side of the stream and re-establish in the Central Region. The project team selected the trailers as the most effective means of transporting the equipment, particularly given the non-invasive means of crossing the Wainui Stream. Negotiations with prime contractor Tranzcarr Heavy Haulage Ltd commenced in mid-2000. The remainder of 2000 was spent in developing concepts with the contractor, detailed designing, preparing the dry docks, haul road and initial mine plan for the Central Region. These activities occurred with no conflict to the normal site production.

Jan 1, 2001

By T Smith, J Hatley

With the increased focus on the need for more uranium mines, this paper presents the design process currently underway for the development of the Millennium deposit in northern Saskatchewan, Canada. This deposit, located 630 - 750 m below surface, will be accessed by two shafts and will be mined by blasthole stoping methods at less than 500 t/d. Mining grade will approximate two per cent U3O8 and mine life is expected to be six to seven years. The project is a joint venture between Cameco, AREVA and JCU. This paper discusses in detail methods used to predict worker radiation exposures, the methods used to monitor the work environment and procedures unique to the uranium industry necessary to minimise worker radiation exposures.

Jan 1, 2008

A discussion on simulation tools to aid the development of robotics platforms is presented. The focus of the work is towards mining robotics platforms where operations are typically in unstructured, unpredictable environments and a high degree of dependability in their operations is required. It is argued that a test-based development approach leads to more robust solutions and faster development cycles than traditional single-track field-only development and that the key enabling technology for this development paradigm is the judicious use of simulation tools. The future direction of simulation for use in online applications such as active planning and as a means to assist tele-operation in high latency communication applications is also brief y considered together with the requirements for a useful simulation environment in terms of the simulator architecture. Finally, a case study is presented on the application of the discussed methodologies to an unmanned ground vehicle (UGV) for earth-moving tasks, which is being developed in an accelerated time frame with a transient development team.

Dec 6, 2010

Recent literature is reviewed with emphasis on the design and scale up of mixers. Most important aspects of mixing have resulted from the study of Newtonian fluids and only a minor attempt has been made to extend the work to non-Newtonian materials.The rheology of non-Newtonian materials is outlined and the typical behaviour of mineral slurries is indicated.The importance of flow velocity, flow pattern, and fluid turbulence is discussed with relation to suspension of solids and rate of reaction.Data on experimental leaching of ore from Mary Kathleen, Queensland, show the effect of different mixing impellers.In conclusion, factors involved in the selection of a mixer are presented with emphasis on economic appraisal after pilot experimentation.INTRODUCTIONThe subject of mixing has attracted considerable attention during recent years, but relatively little work has been undertaken for the study of non-Newtonian materials. Most work has been restricted to Newtonian fluids because there are less inconsistencies in such study.Mixing, by definition, implies blending or combining, and ranges from gentle mixing which blends the contents of a large tank in 24 hours to violent mixing which completely homogenises the contents of a tank within seconds. Metzner and Otto (1957) have pointed out the present lack of knowledge on the degree (or quality) of mixing. Apart from this fact the design of mixers for Newtonian materials would seem to be reasonably certain.Both capital and operating costs rise rapidly with increasing mixer size. Therefore the design, or selection, of a mixer is a matter for economic consideration in the overall aspect of plant design and operation.

Jan 1, 1961

By D Craw, S Clearwater, S Hammit, C Smith

Prior to rehabilitation, plant cover on quartz gravel overburden at Wangaloa coal mine was highly patchy. Stabilisation techniques have since considerably altered the condition of the main overburden yet deposits in the east and west remain largely intact. On the eastern overburden, three distinct zones of revegetation have naturally developed: Zone 1 represents a dense plant cover, Zone 2 a patchy cover and Zone 3 a sparse cover of isolated plants. Aerial photographs show much of the eastern overburden was deposited between 1940 and 1960s. Yet we found that the temporal scale of deposition did not wholly account for the differences observed in vegetation development. To investigate other influential factors, we set up 12 study plots using four replicates in each vegetation zone. The diversity and density of plants in each plot were measured to quantify the degree of vegetation development. Samples from the substrate in each plot were collected using soil cores to a depth of 10 cm. Cores were analysed for indicators of nutrient availability, metal content and physical composition. We found that substrate chemistry varied between individual study plots, but showed little difference overall along the vegetation gradient. Substrate physical differences were much greater. The ratio of coarse quartz pebbles: fines was considerably higher in Zone 3 than other zones, and within zones where plants were not growing. Bulk density also increased successively from Zone 1 - 3. We found clear evidence for the reversed stratigraphy of excavation superimposed over the time scale of deposition, and the corresponding nature of fine particles. The rate of revegetation was therefore highly dependent upon the substrate composition of the last surface deposit from the dumping truck. Our data suggests an optimum ratio exists between inert coarse material and a fine matrix for progressive natural vegetation development on mine substrates.

Jan 1, 2004

Python Underground Processing Plant Critical Design The use of continuous gravity recovery in combination with a controlled breakage fine crushing and screening system followed by flash flotation has been incorporated into the Python processing plant. This provides miners with a flexible, robust, low cost, low energy pre-concentration process for the recovery of gold and/or heavy minerals. The Python plant incorporates fine crushing utilizing either High Pressure Grinding Rolls or Vertical Shaft Impactors in combination with the InLine Pressure Jig and Flash Flotation to continuously liberate and recover the valuable minerals. The use of these technologies has enabled a narrow, transportable pre-concentration plant to be produced which can easily be installed and operated in underground drifts and tunnels.

Sep 13, 2010

By S G. Li

Mine intelligent ventilation is an important guarantee to realise intelligent mining. It is the integration of the Internet of Things, big data, artificial intelligence, internet, cloud computing with ventilation technology, forming a complete ventilation system with intelligent perception, intelligent decisionmaking, intelligent emergency response and airflow control. In order to fully grasp the progress and trends of mine intelligent ventilation research in western China. The paper based on literature analysis and field application research, comprehensively expounds the main research and practical results of mine intelligent ventilation in western China, mainly analyses the development status of key technologies such as accurate and rapid determination of mine ventilation parameters, intelligent analysis and decision-making of ventilation and intelligent regulation of ventilation equipment, and introduces the field test or application of mine intelligent ventilation technology in western China. It lays the foundation reference for related research and improving the intelligent level of mine ventilation.

Oct 12, 2022

By R WOODS

The interaction of, flotation collectors with sulphide mmerals takes place at the solid-solution interface. The electrochemistry of the processes which affect this interface are discussed. The interaction of xanthates with sulphides is an electrochemical process, xanthates being electro-oxidized to chemisorbed xanthate and dixanthogen.The role of oxygen is to provide a cathodic process to allow the anodic oxidation to occur. The hydrophobic condition of the mineral surface is brought about by the presence of the oxidized xanthate species. The action of reagents which can activate or depress the flotation of sulphides is discussed briefly.

Jan 1, 1972

This paper discusses the impacts that advances in metallurgy and process engineering have on minerals project execution. Ausenco's business is focused on integrating minerals processing technology and the delivery of cost effective processing plants that exceed client performance expectations. The metallurgical development is a small but critical part of this process. Metallurgical development and innovation outcomes need to be transformed into an engineered solution and that solution converted into an operating plant in a cost conscious and competitive environment. Including new or innovative processes in a project flow sheet increases a project's technical and commercial risk. However, it also gives the project, and/or the engineering company, a potential advantage over projects using mainline practices. Managing the balance between risk and opportunity has been a cornerstone of Ausenco's success in recent years. Some advances in "technology" that are discussed in the paper include: larger capacity equipment new flow sheet concepts simplification of process interfaces, and more effective project strategies The common theme is that having a new idea can be the easy bit, putting it into operation effectively involves numerous people, many interfaces and strong project management.

Sep 13, 2010

By A Proudman, J Isles, R Lawolo, G Forster

PT Nusa Halmahera Minerals (PT NHM) is an Indonesian joint venture company owned by Newcrest Mining Limited (75 per cent) and PT Aneka Tambang (Persero) (25 per cent). PT NHM operates two underground gold mines, Kencana and Toguraci at the Gosowong mine site in North Halmahera District, North Maluku Province, Indonesia.Due to several major stope overbreak events at Toguraci, the mining method and sequence was reviewed. The method was changed from a bottom up Avoca stoping approach using waste rock as fill material and leaving sill pillars, to a top down open stope method using paste fill without sill pillars.The revised mine plan originally had stoping progressing from the current level to the base of reserves followed by extraction of the sill pillars in the upper levels at the end of mine life. Geotechnical modelling was conducted on the revised mine plan and it was recommended that the sill pillars be taken early due to the risk of them overstressing and being difficult to recover if left until the end of mine life. The backfill material above the sill pillars is unconsolidated run-of-mine development waste rock or unconsolidated rock fill (URF).Due to earlier attempts to extract sill pillars under URF not being successful in the upper areas of the mine, it was stipulated that the URF above the five remaining pillars must be consolidated prior to stoping. Cost benefit analysis showed this to be justifiable due to the high-grade nature of the ore locked up in the pillars.Grout was initially planned to be injected in one pass through self-drilling anchors (SDA) in a 2.5 m pattern. Initial attempts to do this failed due to the SDA aperture and grout consistency. A modified method was employed using poly pipe installed into open holes that were drilled through the sill pillar and into the URF from below. Repeated application at each location ensured full grout consolidation. Drill holes were used to confirm grout thickness as well as add more grout. Design thickness was based on stress analysis.Despite different URF types being present due to varying quantities of fines, the process was similar for each area. The presence of paste in the URF of one target affected the quantity of grout it received.With a design thickness of 4–5 m of consolidation in the URF, depending on stope width and dip, each consolidated pillar (to date) maintained integrity during the stope operation. Some fall of material was anticipated; however, quality assurance / quality control (QA/QC) during grouting, staged stope extraction and careful blast design minimised fall of material.CITATION:Proudman, A, Isles, J, Lawolo, R and Forster, G, 2017. Rock fill consolidation for the extraction of sill pillar stopes at Toguraci gold mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 199–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By R Symes

The Fosterville Goldmine in Victoria Australia employs the BIOX« Process to liberate gold from its sulfidic flotation concentrate through bacterial oxidation. Gold occurrence is primarily as submicron particles in pyrite and arsenopyrite and has been described as being in æsolid solutionÆ and therefore not amenable to direct cyanidation. Once liberated by the oxidation process, the gold is then available for cyanide leaching. During the oxidation process it has been found that a portion of the liberated gold becomes suspended in the liquid phase in what appears to be a colloidal state. This liquid becomes a waste stream during washing of the oxidised solids and the suspended gold is therefore lost. A method was previously developed using an addition of quebracho tannin to significantly reduce this loss by formation of an iron-tannin precipitate which captures the gold which then reports to the cyanide leach circuit with the oxidised concentrate solids onto which it is adsorbed.This paper discusses the development and plant trial of a second processing step to further enhance gold recovery by use of flotation tailings essentially as a source of extra surface area to capture residual tannin-iron precipitate and its associated gold not recovered in the first step.CITATION:Symes, R, 2012. Recovery of colloidal gold from oxidised concentrate wash liquor - Further improvement, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 383-388 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

After some 50 years of worldwide research in relation to coal pillar mechanics and design as well as numerous workshops and technical papers related to these issues there is still some significant disagreement as to the approach one should adopt in the assessment and design of a coal pillar. Of course there are many different types of coal pillars that fulfil a wide range of roles at any particular mine and in this instance it is appropriate to have a 'tailored' approach for each pillar type in relation to the role it fulfils. However where it can become very difficult for the mine operators is when various researchers or consultants use or recommend significantly different approaches for the same type of pillar fulfilling the same role. By 1999 two pillar design techniques had been developed specifically for the Australian underground coal mining industry (ie The University of New South Wales Pillar Design Procedure, UNSW PDP and Analysis of Longwall Tailgate Serviceability, ALTS) and several other pillar design techniques were being practiced by individual consultants. The Australian industry hoped to resolve the issue of what technique to use for each pillar type and role, when it funded UNSW in 2000 to develop a 'Systems Approach to Pillar Design'. The findings of the abovementioned project were published in 2005 and while every attempt was made by UNSW to include the views of various local and overseas researchers and consultants it would be fair to say that a unified approach to pillar design in Australia was not adopted as a result of that project. This is the experience of one country where there has never been one central group solely undertaking such research in relation to pillar design (such as the Chamber of Mines in South Africa). This paper explores the Australian experience in terms of pillar research and what that experience may offer to researchers in Australia and other countries. At the First Australasian Ground Control in Mining Conference (2003) the first 'update' of the ALTS Design Methodology (ie ALTS II) was presented. In subsequent years the ALTS database was continually updated and significantly expanded such that it now includes detailed information in relation to both the tailgate (148 cases) and maingate belt road (58 cases). In addition to tailgate roof support and chain pillar design, the current version of ALTS (referred to as ALTS 2009) includes a maingate belt road roof support design module. This paper is also intended to update and summarise the development and application of the ALTS Design Methodology for longwall gateroad design over the last decade both directly and in the context of coal pillar research conducted in Australia over the last 15 years.

Nov 25, 2010

Ledcap Pty Ltd has developed two software tools for assisting in the determination of life-of-mine (LOM) trucking requirements. The first tool generates haul paths and the second calculates truck travel time over these paths. The two step approach allows the paths to be viewed and if required edited, to better represent the actual site haul routes.The first tool automatically creates haul paths between the mine bench and the dump. To do this the user supplies a master haul route and a scheduled block model. The master haul path and the block model are interacted to create multiple haul routes, one for each pit/dump bench pair in each scheduling period. Each path carries with it a record of the scheduling period it represents and the dry tonnage hauled over the path in that period.The second tool calculates truck travel time over the path. Data from the manufacturer's rimpull and retarder curves are used to calculate accelerations and speed over each segment of the haul path. As the paths are derived from digitised representations of mine haul routes the path f les often have over a hundred segments. This detailed representation of the haul route allows the software to automatically adjust speed for different radius corners and accurately simulates the changing accelerations over the gradient changes that occur in real life mine ramps. Rolling resistance can be specified at a global level, at a segment level and at a period level. This allows rolling resistance to be changed seasonally as well as spatially.Life-of-mine trucking studies attempt to calculate an accurate answer from extremely variable inputs. This paper will detail the features of the two software tools and how the tools provided in the software can assist the mine planner to have greater confidence in their life-of-mine trucking requirements and the subsequent production capacity inputs to their scheduling calculations.

Dec 6, 2010

By A Gerdes, H BrStz, E GSbler, D Davis, F Henjes-Kunst, S Dewaele, T Graupner, T Oberthnr, M Sitnikova

Following the United Nations initiative to fingerprint the origin of conflict materials, the German Federal Ministry for Economic Cooperation and Development has decided to fund a pilot study on coltan ores. Since 2006, our working group has been investigating columbite- tantalite (coltan) mineralisation, especially in Africa, also within the wider framework of establishing certified trade chains. More than 300 samples were obtained from the worldÆs major coltan producing areas. Special attention is, however, directed to samples and concentrates from Ta-Nb-Sn provinces in Africa: Democratic Republic of the Congo, Rwanda, Mozambique, Ethiopia and Namibia. Using state of the art analytical tools, we investigate mineralogical and chemical parameters obtained from columbite-tantalite ores and concentrates in order to distinguish between ore provinces, likely even down to the deposit scale. Methods employed include fully automated electron microscopy (mineral liberation analysis), electron microprobe analysis (major and minor elements), laser ablation plasma-source mass spectrometry (trace elements and U-Pb dating), X-ray fluorescence spectroscopy (bulk major and trace elements), X-ray diffraction analysis (mineralogy and structure) and thermal-ionisation mass-spectrometry (U-Pb dating). Major and trace element concentration patterns, mineral assemblages in the ore concentrates, and zoning characteristics in the different pegmatites from Africa distinctly differ from each other. Furthermore, the following age populations are evident:Archaean (>2.6 Ga);Palaeoproterozoic (1.9 - 2.1 Ga);early Neoproterozoic (æKibaranÆ; 0.98 - 0.93 Ga); andlate Neoproterozoic to early Palaeozoic (ca 0.5 Ga). Currently, we focus on the resolution of the fingerprinting system from region via ore province down to deposit scale. Our preliminary analytical results indicate that a certification scheme including fingerprinting of sources of coltan ores is feasible.

Jan 1, 2008

This paper presents an overview of a program PC-BC developed for application to the design and evaluation of block cave operations. Conventional mine planning software tools are not well suited to the evaluation of this type of deposit. The paper looks at the modelling approach as applied to a block cave mining project. The following steps are described:Initial preparation of data including block models, draw point footprint geometry and draw cone geometry. Computation of individual draw point reserves. Procedure for modelling of vertical mixing of material within each draw point and subsequent determination of the best height of draw for each draw point based upon an economic cut-off value. Smoothing of draw heights amongst neighbouring draw points to produce a realistic draw envelope. Mineable reserves within the envelope are then computed. Tools for preparation and evaluation of various production schedules. This includes definition of draw rates, and rates for commissioning new draw points. In an operating mine, the capture and analysis of daily draw tonnages is important. How PC-BC accommodates this is described as well as the processes for depleting the draw column reserves. In the 12 years since the program was first developed, it has been used on a number of projects for feasibility studies and operating mines. Some practical examples of the use of the program in these projects are presented. Finally, some commentary on the sensitivity of various parameters is presented. Particular emphasis is placed on the overall footprint design.

Jan 1, 2000

By W Shamu

The mechanical properties of rock samples of identical lithologicalcomposition may vary significantly due to existence of materialdiscontinuities. Laboratory tests were carried out to determine the effect of material discontinuities on rock sample mechanical properties. The investigations consisted of detecting discontinuities, observing the failure mechanisms during uniaxial compressive strength tests, and analysing of the factors affecting the strength. A non-destructive testing method has been adopted to assist in thedetection of discontinuities. Laboratory testing proved that fractures leading to failures initiated on the detected discontinuities. The location, orientation, size, density and extent of the discontinuities contribute to different modes of failure and these affect the mechanical parameters of rock samples. Four modes of failure were distinguished for hard and brittlecylindrical rock samples. These modes were referred to as simple shear failure, multiple shear failure, multiple fracturing and vertical splitting. To evaluate the effect of discontinuities on mechanical parameters, the ratio of uniaxial compressive to tensile (Brazilian) strength was calculated and analysed for the different modes of failure. It was found that the value of the ratio depended on the mode of sample failure. The lowest value of the ratio was observed for shear mode of failure and the highest for vertical splitting mode of failure.

Jan 1, 1999

A description of:1. Air-lock at No. 14 Upcast shaft.2. Pit-top gates at Dudley winding shaft.3. Safety rider employed in sinking No. 18 shaft.1. AIR-LOCK AT No. 14 SHAFT.Some time ago it became desirable to raise and lower the McBride tunnel men to save them walking the inclined tunnel, about a mile in length, with a dip of nearly 600 ft., and a maximum gradient of 1 in 4. The main Upcast shaft, No. 14, was, therefore, equipped for winding the men. As this shaft was the main ventilating shaft for the McBride tunnel mine, it was necessary to take the greatest precautions against leakage of air. The writer therefore devised the concrete structure shown in Plate 1.The structure, as shown, surrounds the shaft inside the poppet legs. As the men are wound on double-decked cages (twelve men to each deck) provision is made at both top and bottom for the two decks to be loaded and emptied simultaneously. The doorsover the sky shaft, shown in the drawing, have been cut out and the sky shaft has been close-timbered with a double layer of T. and G. flooring boards, with building paper between, nearly up to the thimble frame, a small hole only being left for the winding rope topass through. The space between the ramps is glazed with plate glass to allow the winding-engine driver a good view of the pit top.The men are wound from two levels, 302 ft. and 611 ft.2. PIT-TOP GATES AT DUDLEY WINDING SHAFTTo minimise the shock to cage, couplings and rope when winding quickly, the writer devised the apparatus and arrangement shown in Plate n.

Jan 1, 1928