Search Documents

By Gerhard Derge, J. Warren Stewart

Extrusion processes are used in the commercial production of a wide variety of products, as indicated by the review presented a few years ago by D. K. Crampton.' Most writers have confined themselves to a general description of the equipment and products and the engineering aspects of the process. The few studies that have dealt with the metallurgical side of extrusion have been concerned primarily with an examination of the mode of flow of the metal during extrusion. This has been accomplished by the use of composite billets, by scribing grids on symmetrical sections of billets and observing the change of dimensions in the gridwork, or by examining microstructures in extruded sections.2"8 Ariotlier limitation of these original studies is that they were confined to the extrusion of very simple shapes, usually rods having a diameter of about one-fourth that of the billet. Tin is particularly well suited to the extrusion of collapsible tubes and similar shapes in which the extruded section is very small in comparison to the diameter of the billet or slug. In modern production, impact extrusion methods are generally employed, therefore the thickness of the slug is small compared to its diameter. Under these conditions the process differs considerably from the processes that have been most fully described in the literature, and it is known that the quality of the product is very sensitive to slight variations in any one of the many variable factors involved, such as coinposition and structure of the alloy, rate of extrusion, temperature, shape of punch and die. An exhaustive examination of all of the above-mentioned problems promises to produce so many data that it seems advisable to initiate the reports at this time, even though all of the factors outlined have not been examined fully, and to confine this paper to a description of the apparatus and method. Only tin and its alloys with small amounts of copper have been considered. These are the alloys most commonly used in this country for the production of the type of articles already described.

Jan 1, 1940

By Gerhard Derge, J. Warren Stewart

Extrusion processes are used in the commercial production of a wide variety of products, as indicated by the review presented a few years ago by D. K. Crampton.' Most writers have confined themselves to a general description of the equipment and products and the engineering aspects of the process. The few studies that have dealt with the metallurgical side of extrusion have been concerned primarily with an examination of the mode of flow of the metal during extrusion. This has been accomplished by the use of composite billets, by scribing grids on symmetrical sections of billets and observing the change of dimensions in the gridwork, or by examining microstructures in extruded sections.2"8 Ariotlier limitation of these original studies is that they were confined to the extrusion of very simple shapes, usually rods having a diameter of about one-fourth that of the billet. Tin is particularly well suited to the extrusion of collapsible tubes and similar shapes in which the extruded section is very small in comparison to the diameter of the billet or slug. In modern production, impact extrusion methods are generally employed, therefore the thickness of the slug is small compared to its diameter. Under these conditions the process differs considerably from the processes that have been most fully described in the literature, and it is known that the quality of the product is very sensitive to slight variations in any one of the many variable factors involved, such as coinposition and structure of the alloy, rate of extrusion, temperature, shape of punch and die. An exhaustive examination of all of the above-mentioned problems promises to produce so many data that it seems advisable to initiate the reports at this time, even though all of the factors outlined have not been examined fully, and to confine this paper to a description of the apparatus and method. Only tin and its alloys with small amounts of copper have been considered. These are the alloys most commonly used in this country for the production of the type of articles already described.

Jan 1, 1940

By D. J. Cox, J. P. Conway, A. E. Gooch

A two-year test conducted by the USBM's Spokane Mining Research Center (SMRC) has proven the feasibility of the yielding rockbolt, a concept which may prove very useful to the mining industry by providing ground support under a variety of conditions. The yielding rockbolt was originally developed in South Africa3 to overcome the limitations of conventional bolting in rock subjected to high-stress or rock burst conditions. The yielding effect is obtained by fitting the bolt prior to thread rolling with a smooth-bore die of internal diameter slightly larger than the shank diameter but smaller than the rolled thread diameter.

Jan 4, 1977

By Harry H. Power

INDUSTRY has the right to expect the petroleum engineering schools to supply more than the minimum technical qualifications necessary to obtain or discharge the responsibilities of a particular job. The basic training, social and economic orientation, should go far beyond these minimum requirements. Petroleum engineering students should also be well grounded in the history of the oil business so that they may understand the industry's progress since the advent of the Drake well. Furthermore, according to P. H. Bohart, the schools "have a definite duty to help the students form a workable philosophy of life, which includes an appreciation of the service of science to mankind, and a belief in the obligation of the individual who enters a profession to exalt himself by continuing his studies and growth so that he may never cease making contributions to the advancement of science and industry."

Jan 1, 1948

By F. G. Miller, E. B. Wilson

In 1972, coal mine productivity was in steady decline and labor and maintenance costs were spiralling upward. Yet, despite this sad state of affairs, nowhere in the US at that time was there a comprehensive and coordinated coal research and development plan in the offing. The Bureau of Mines had not yet been charged with such a responsibility, and industry was content to rely on machinery manufacturers for innovations. It was during this period that Bethlehem Steel Corp. determined that a new approach to coal mining research was needed for the industry as well as for the company itself. After studying Bethlehem's own mining practices, the state-of-the-art of mining research elsewhere, and development work by manufacturers, a comprehensive research package was presented to company management in late 1972. The ideas and experience of many operating and management personnel in the company contributed to the formulation of the final plan as approved.

Jan 10, 1976

26. G. H. S. Price, S. V. Williams, and G. J.O. Garrard: Heavy alloy, its production. properties and uses. Metal Industry (1941) 599 354s 372. 394. 27. R. Kieffer and W. Hotop: p. 320 of ref 12. 28. F. R. Hensel. E. I. Larsen, and E. F. Swazy: Physical properties of metal compositions with a refractory metal base. Chap. 42, 483, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 29. R. Kieffer and W. Hotop: p. 290 of ref. 12. 30. H. Freundlich: Kapillarchemie. 211 (1923) Leipzig. 31. W. Ostwald: Zisch. f. Phys. Chemie. (1900) 34, 503. 32. G. A. Hulett: Zisch. f. Phys. Chemie. (1901) 37. 385; and (1904) 47, 357. 33. J C. Chaston: Discussion to Price, Smithells and Williams, p. 257 of ref. 4. 34. W. Dawihl: Untersuchungen ueber die Vorgaenge bei der Abnuetzung von Hartmetallwerkzeugen. Ztsch. f. techn. Phys. (1940) 21 336. 35. W. Dawihl and J. Hinnueber: Ueber den Aufbau der Hartmetallegierungen. Kol-loidzlsch. (1943) 104, 233. 36. F. Skaupy: Dispersoidchemische und verwandte Gesichtspunkte bei Sinter-hartmetallen. Kolloidzlsch. (1942) 98, 92; and (1943) 102, 269. 37. F. C. Kellcy: Cemented tantalum car- bide tools. Trans. ASST (1932) 19, 233. 38. E. W. Engle: Cemented carbides. Chap. 39, 436, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 39. W. Dawihl: Zlsch. f. Melallkunde. (1940) 32, 320. 40. P. M. McKenna: Tool Materials (Ce- mented Carbides). Chap. 40. 454. Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 41. G. A. Meerson. G. L. Sverev, B. Y. Osinovskaja: Zhurnal Prikladnoi Khimii. (1930) 139 66. 42. A. G. Metcalfe: The mutual solid solubility of Tunesten Carbide and Titanium carbide- Metal Trealmenl (1946) 13, 127. 43. P. Schwarzkopf: Powder Metallurgy. 196-201 and 354-356 (1947) New York. 44. H. Burden: The manipulation and sintering of hard-metals. Special Rep. No. 38, p. 78. Iron and Steel Inst.. 1947. London. 45. W. D. Jones: Principles of powder metal- lurgy. 150. (1937) London. 46. J. E. Drapeau: Sintering of powdered copper-tin mixtures. Chap. 32. 332, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 47. H. E. Hall: Sintering of copper and tin powder. Metals and Alloys (1939) 10, 297. 48. F. Sauerwald: Present status of powder metallurgy. -.Melallwirlschafl. (1941) 20, 649. 671. 49. H. L. Wain: Powder metallurgy; influence of some processing variables on the properties of sintered bronze. Report ACA-25. Australian Council for Aeronautics (1946) Melbourne. 50. S. L. Hoyt: Constitution of copper-tin alloys. Metals Handhook, 1364. (1939) Cleveland. 51. T. Ishikawa: Studies on the interdiffusion of copper, tin and graphite powders. Nippon Kinzoku Gakkai-Si (1937) I, 226. 52. A. Carter and A. G. Metcalfe. The struc- ture of porous bronze bearings. Special Rep. No. 38, p. 99. Iron and Stecl Inst. (1947) London. 53. R. P. Koehring: Sintering atmospheres for production purposes. Chap. 25, 278. Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 54. C. G. Goetzel: Some properties of sintcred and hotpressed copper tin compacts. Trans. AIME (1945) 161, 569. 55. J. W. Lennox: The production of some non ferrous engineering components by powder metallurgy. Special Rep. No. 38. p. 174. Iron and Steel Inst., 1947, London. . P. Duwez and H. E. Martens: The power metallurgy of porous metals and alloys having a controlled porosity. TP 2343, Metals Tech. April 1948. This volume. p. 848. 57. E. A. Owen and L. Pickup: X-ray study of the interdiffusion of copper and zinc. Proc. Royal Soc., London, Series A. (1935) 149, 283. 58. C. G. Goetzel: Sintered and hotpressed compacts of copper-zinc powder. Chap. 34. 352, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. 98, R. Chadwick. E. R. Broadfield, and S. F. Pugh: Observations on the pressing. sintering, and properties of iron-copper powder mixtures. Special Rep. No. 38, p. 151, Iron and Steel Inst. (1947) London. 60. A. Squire: The properties of iron-copper compacts. Watertown Arsenal Lab. Rep. WAL No. 67101. 61. F. C. Kelley: Properties of sintered iron- comer uowder. Iron Age (Aug. 15. 193) 158 57. 62. G. H. Howe: Sinterinn of Alnico. Iron Age (Jan. 11. 1940) 14.5, 27. 63. R. Kieffer and W. Hotop: p. 359 of ref. 12. 64. W. Hotop: Permanent magnets from sintered iron-nickel-aluminum. Stahl und Eisen (1941) 61, 1105. 65. P. R. Kalischer: Some experiments in the production of aluminum-nickel-iron alloys by powder metallurgy. Trans. AIME (1941) 145, 369. 66. S. J. Garvin: Production of sintered per- manent magnets. Special Rep. NO. 38. p. 67. Iron and Steel Inst. 1947, London. 67. F. C. Kelley: Discussion to P. R. Kalischer. p. 375 of ref. 65. 68. R. Kieffer and W. Hotop: p. 357 of ret, 12. 69. C. H. Howe: Sintered alnico. Chapter 48, 530, Powder Metallurgy, ed. by J. Wulff (1942) Cleveland. Powder Metallurgy Seminar (C. G. Goetzel presiding) C. G. Goetzel—The seminar has been opened by a man who has been active in the field for over fourteen years and has made, since then, some major contributions to the advancement of the art. After having been associated with the Moraine Products Division of General Motors Corporation for over ten

Jan 1, 1949

Jan 1, 1960

By R. Greenwood

The advent of the space age and its promise of interplanetary flight has prompted new ideas for propulsion systems that will allow maximum energy with minimum fuel weight. The use of cesium as the source of energy for such rocket flights has been found desirable. Theoretical efficiency of a rocket fuel is measured in terms of specific impulse, defined as the number of pounds of thrust per pound of propellant consumed per second. Specific impulse is usually expressed in seconds (the number of seconds for which one pound of fuel would produce one pound of thrust) although it is really a measure of total energy, not of power. The most sophisticated chemical fuels have a specific impulse of 300 to 400 sec; liquid hydrogen heated by nuclear reactor has a specific impulse of 1000 to 1200 sec. Specific impulses as high as 20,000 sec, however, are theoretically attainable with the ion rocket, in which free cesium ions are accelerated across a voltage drop and ejected at high velocity.' Characteristics of the system have been sketched by Boden.2 The desirable properties of an ion propellant are: 1) low ionization potential, 2) low boiling point, and 3) high atomic weight. Alkali metals best fulfill these requirements, and Table I indicates the superiority of cesium. The use of heavy complex ions such as UCl3 is ruled out by their instability and other disadvantages.' Despite its enormous superiority in specific impulse, the ion rocket is inherently low-powered, capable of very small acceleration. Application of ion propulsion will be limited to large rockets and spaceships on missions requiring powered flight for weeks or months and employing a separate chemical propulsion system for escape from the earth's atmosphere where power requirements are large but of brief duration. For example, Kraemer and Larson3 considered the case of an unmanned 25,000-lb pay-load placed in a 300-mile orbit by chemical rockets, proceeding thence by ion propulsion to the vicinity of Mars, where it would go into orbit once again. Calculations provide for 8500 lb of cesium for such a voyage. The question of whether such quantities of cesium will be readily available to the space program does not appear to have been considered by geologists and mining engineers. Present Production and Uses Literature on industrial applications of cesium is scanty. The metal is used in scintillation counters, photocells, infra-red detection devices, and as a "getter" in low-voltage vacuum tubes. Production is sporadic and total figures are not published, but the annual consumption is measured in pounds rather than in tons. The few pollucite deposits known, small as they are, can easily supply the present limited demand for gram or pound lots of cesium. Until recently the price of cesium was $2 to $4 per gram, but according to Chemical Engineering, cesium salts are now available at $13 to $27.50 per lb. Geochemical Distribution As a large alkali ion, the cesium ion accompanies potassium in geological processes and tends to be concentrated in the latest crystallizing fractions of potassium minerals in much the same manner as rubidium. Most of the cesium in igneous rocks, therefore, is in the micas and potash feldspars of granites, and especially in granitic pegmatites. The cesium content rises markedly in the micas of the late by-drothermal replacement stage in complex pegmatite~.' Typically, cesium is only 0.5 to 0.01 times as abundant as rubidium in potassium minerals. Rb', with a radius of 1.47 A, is close enough in size to K' (1.33 A) so that rubidium forms no minerals of its own. Cs+ is so large (1.67 A) that only small concentrations can be taken up in potassium minerals; when cesium is present in solution in larger concentration it forms the mineral pollucite, Cs3-Na2A17Si17O48.3H2O, which is known only in pegmatites. In the weathering of igneous rocks, cesium is dissolved, carried to the ocean, and apparently in-

Jan 1, 1961

By F. M. Sandoval, R. E. Ries, J. F. Power

Returning the original soil material to the surface of smoothed mine spoils is a practical means of restoring agricultural productivity. Research has established that high-sodium spoils in North Dakota: (1) must be covered with about 70 cm of soil material to achieve maximum production; (2) top-soil must be segregated and spread separately from subsoil; (3) potential production depends on the quality of the soil material returned; and (4) erosion and upward salt movement must be controlled for sustained production. Erosion is best controlled by reducing final grades as much as possible during the smoothing process followed by prompt establishment of vegetation.

Jan 12, 1979

By E. A. Anderson, P. W. Ramsey, E. J. Boyle

Only a few zinc-rich alloys are in commercial use today, and these depend largely upon solid solution effects for their desirable properties. Typical examples are rolled alloys containing about 1 Per cent of copper, with Or without additions of elements such as magnesium, and die-casting alloys containing about 4 Per cent of aluminum with small amounts of magnesium and sometimes copper." A number of elements are capable of forming alloys with zinc, Which do not enter into solid solution except in limited degree. The Present Paper considers One such system, zinc-titanium, in which alloys having potentially useful properties in the rolled form were found. Zinc-titanium System The zinc-rich portion of the zinc-titanium diagram, as determined by standard methods in this laboratory,3 is shown in Fig. I. The portion of the diagram of significance in the present work extends from 0 to about 0.5 per cent titanium. Gebhardt4 places the eutectic at 0.45 per cent, but the evidence in favor 01 the composition given in Fig. I is considerable. The solid solubility of titanium in zinc is very low indeed and possibly places these alloys in a somewhat different category from the commercial alloys previously mentioned. Alloy Preparation All of the alloys used in this work were prepared with titanium metal of 98.9 per cent purity. In most cases high-purity zinc (99.99 per cent) was used but sufficient work was done later to show that zinc of about high-grade composition would yield approximately equal results. Best practice in alloy manufacture seemed to be to prepare a zinc-titanium hardener by adding about 4 per cent of titanium metal to molten zinc and holding under a boric acid cover, with frequent stirrings, at 750°C, until the titanium had dissolved. The desired titanium content could readily be obtained in the final alloy by adding the calculated amount 01 this hardener. The alloys proved to be quite stable in composition, unless overheated, and, with reasonable temperature control, required no cover or flux to prevent loss of titanium content by oxidatioll, Hot-rollig Tests Three alloys containing, by analysis, 0.05, 0.12, and 0.23 per cent titanium were selected for preliminary study. Slab cross sections a a marked grain refinement* (Fig. 2) in the two alloys of highest titanium content. Cast unalloyed zinc has a columnar grain structure similar to that shown for the alloy of lowest titanium content but without the scatter of small equiaxed grains at the center.

Jan 1, 1944

By P. W. Ramsey, E. J. Boyle, E. A. Anderson

Only a few zinc-rich alloys are in commercial use today, and these depend largely upon solid solution effects for their desirable properties. Typical examples are rolled alloys containing about 1 Per cent of copper, with Or without additions of elements such as magnesium, and die-casting alloys containing about 4 Per cent of aluminum with small amounts of magnesium and sometimes copper." A number of elements are capable of forming alloys with zinc, Which do not enter into solid solution except in limited degree. The Present Paper considers One such system, zinc-titanium, in which alloys having potentially useful properties in the rolled form were found. Zinc-titanium System The zinc-rich portion of the zinc-titanium diagram, as determined by standard methods in this laboratory,3 is shown in Fig. I. The portion of the diagram of significance in the present work extends from 0 to about 0.5 per cent titanium. Gebhardt4 places the eutectic at 0.45 per cent, but the evidence in favor 01 the composition given in Fig. I is considerable. The solid solubility of titanium in zinc is very low indeed and possibly places these alloys in a somewhat different category from the commercial alloys previously mentioned. Alloy Preparation All of the alloys used in this work were prepared with titanium metal of 98.9 per cent purity. In most cases high-purity zinc (99.99 per cent) was used but sufficient work was done later to show that zinc of about high-grade composition would yield approximately equal results. Best practice in alloy manufacture seemed to be to prepare a zinc-titanium hardener by adding about 4 per cent of titanium metal to molten zinc and holding under a boric acid cover, with frequent stirrings, at 750°C, until the titanium had dissolved. The desired titanium content could readily be obtained in the final alloy by adding the calculated amount 01 this hardener. The alloys proved to be quite stable in composition, unless overheated, and, with reasonable temperature control, required no cover or flux to prevent loss of titanium content by oxidatioll, Hot-rollig Tests Three alloys containing, by analysis, 0.05, 0.12, and 0.23 per cent titanium were selected for preliminary study. Slab cross sections a a marked grain refinement* (Fig. 2) in the two alloys of highest titanium content. Cast unalloyed zinc has a columnar grain structure similar to that shown for the alloy of lowest titanium content but without the scatter of small equiaxed grains at the center.

Jan 1, 1944

In 1973, US Borax & Chemical Corp. began investing three days wages and about $20 in training materials in every new employee before having him report to his first job. The result? Accidents involving new employees in the past two years have dropped by more than half from the 1972 level. What made this success possible was safety training done with programmed instruction materials-which, incidentally, US Borax also uses for vocational training.

Jan 4, 1976

By F. M. Sandoval, R. E. Ries, J. F. Power

Returning the original soil material to the surface of smoothed mine spoils is a practical means of restoring agricultural productivity. Research has established that high-sodium spoils in North Dakota: (1) must be covered with about 70 cm of soil material to achieve maximum production; (2) top-soil must be segregated and spread separately from subsoil; (3) potential production depends on the quality of the soil material returned; and (4) erosion and upward salt movement must be controlled for sustained production. Erosion is best controlled by reducing final grades as much as possible during the smoothing process followed by prompt establishment of vegetation.

Jan 1, 1980

By E. J. Bonet, P. B. Crawford

It is fairly common practice to reinject water into the aquifer near the oil-water interface in water-drive reservoirs. There have been many studies of aquifer behavior without reinjection,l-5 but apparently no analytical studies have been made to indicate performance when injection wells are present in the aquifer. The diffusivity equation may be used to describe the pressure behavior in an aquifer. When sources are present it can be written as A general solution of Eq. 1 may be obtained as the sum of two solutions. One is a general solution of the homogeneous equation, obtained by dropping the source term in Eq. 1 and still satisfying the required boundary conditions. Another is a general solution of Eq. 1 satisfying homogeneous boundary conditions.1° The first solution, which corresponds to the aquifer without reinjection, has been given quantitative and qualitative treatment in the literature.l-5,8,9 The latter solution will be treated here. Solutions with variable injection rates are obtained by superimposing solutions with constant rates, so we have considered only the latter. Five cases have been treated here: 1. A linear aquifer of finite width and extent. Water is injected into the aquifer at point xo, yo at constant rate. The pressure along the line x = 0 is maintained at zero pressure. (See Fig. 1.) Equations showing the pressure distribution, rates, velocity and cumulative influx have been developed. Certain numerical results are shown. 2. A linear aquifer of finite width and extent. Water is injected into the aquifer at point xo, yo at constant rate. The rate of production along the oil-water water contact is maintained constant. Equations showing the pressure distribution inside the aquifer are presented. 3. A linear aquifer of finite width and extent. Constant pressures are maintained at opposite ends of the aquifer. Water is injected at constant rates at point xo, yo. Equations showing the pressure distribution are shown. 4. A linear aquifer of finite width and infinite extent. The pressure is maintained constant at the oil-water contact. Water is injected at a constant rate at point xo, YO. 5. A linear aquifer of finite width and finite extent. The pressure at the oil-water contact is maintained constant. Water is injected at constant rate per unit length along a line x,. The Linear Aquifer The linear closed aquifer, performing at constant terminal pressure was selected as the first case to be analyzed. The development of the equations is based on uniform injection per unit of thickness, and gravity effects are neglected. In practical application this condition is probably most closely achieved when the

Jan 1, 1970

By T. L. Joseph

BLAST furnaces are most efficient thermally when the C02 in the top gas is highest. Oxygen introduced in the air blast is converted to CO in the combustion zones. The extent to which CO, generated in front of the tuyères, is converted later to C02 depends upon the ratio of ore to coke in the charge and the degree to which C02, formed by reduction of iron oxides with CO, reverts to CO by the secondary reaction C + C02 = 2C0. About 300 to 400 lb. of carbon1 per ton of pig iron is normally involved in the solution-loss reaction or direct reduction of FeO with carbon, which produces the same over-all results; that is, lower C02 in the top gas. Riche has recently reported a reduction in fuel consumption at slower rates of blowing on two furnaces in spite of higher heat losses per ton of iron. Lower fuel consumption at slow operating rates was due to more complete reduction of the ore that resulted in higher C02 in the top gas and consequently more efficient use of carbon. Kinney3 has reported substantial savings in fuel as a result of crushing and sizing the ore charge. Improvements in practice brought about by sintering magnetite concentrates, flue dust and fine ores have been due to the establishment of conditions favoring more complete reduction of the ore in the upper part of the furnace. The extent to which oxides and fluctuations in composition in pig iron affect the quality of steel and finished product needs further study. There is evidence that more thorough preheating and reduction of the ore in the upper part of the furnace tend to give a better quality of iron. Bogatzkii4 found from laboratory work that the amount of oxygen enter-

Jan 1, 1936

By AIME AIME

SOME 65 members of the Institute, including most of the Local Section delegates and several Directors and officers, were on hand for the Annual Business Meeting of the Institute held in the Engineering Societies Building on Monday, Feb. 21, at 4:30 p.m., immediately following the second session of the Local Section Delegates Conference. President Mathewson presided. The meeting was largely taken up with the presentation of committee re- ports, discussion of which was invited. F. E. Wormser presented the report of the Admissions Committee ; Philip Kraft, Papers and Publications Com-

Jan 1, 1944

By Richard Miller

RECENT studies of creep have made it apparent that plastic deforma-tion may occur in metals under stresses less than the elastic limit as deter-mined from short-time tests. In summarizing conclusions drawn from creep tests by various investigators, Tapsell1 said: "It is evident that if a material has a true elastic range, the elastic limit must represent the maximum stress for no creep." The presence of a. definite elastic limit, represented in single crystals by a critical or threshold shearing stress, is claimed by Schmid2, Elam3 and others who have investigated the plastic deformation of single crystals. However, this "law of critical shearing stress" was deter-mined2 from short-time tests, and the measurement of the deformation was made with apparatus primarily designed to observe large amounts of plastic deformation, not to detect elastic changes. Experimental data recently obtained with highly sensitive instru-ments by A. W. Hanson4 on zinc and by Podaschowsky5 on rock salt indicate that the elastic range in single crystals is considerably narrower than formerly was supposed. Moreover, a theoretical possibility of permanent deformation, under the influence of even the smallest shear stress in single crystals above a certain temperature (Td), has been developed by G. I. Taylor6. This evidence seemed to warrant an examination of the elastic limit in large single crystals by means of creep tests. The first metal chosen for examination was zinc.

Jan 1, 1936

By Arthur E. Granger

IN the early days of the science, and until the recent past, geologists worked as individuals or in small groups. Prior to 1930 perhaps the largest single group under one administrative head was the Geologic Branch (now Division) of the U. S. Geological Survey, which employed at that time (including temporary help) 100 to 150 geologists. Today that same unit employs some 1500. In industry some companies employ as many as 100 geologists in a single department. These numbers obviously pose a need for administration. The basic qualifications for good administration are the same for any group of human beings, but the administration of geologists presents some special problems. Choosing Administrative Personnel: There are two kinds of personnel needs: 1) technical, which requires professional geologists who have proved their capabilities in the field, and 2) clerical and fiscal, which provide the necessary supporting or housekeeping functions. This discussion will be concerned only with the first category, except to point out the need for competent and understanding help from clerical and fiscal people and close relationship between top administration, technical or professional personnel, and the clerical and fiscal groups.

Jan 7, 1957

By W. H. Ode, W. A. Selvig

By plotting fixed carbon against British thermal units of coals free from mineral matter, and ranging in rank from anthracite to lignite, it is found that the coals of higher rank, from anthracite to the higher rank of the high-volatile bituminous coals, inclusive, can be separated into groups according to their degree of metamorphism by reference to their fixed carbon. Such charts show also that the coals lower in rank can be best separated into groups with respect to B.t.u., especially when plotted on the moist basis, that is, coal containing its natural bed moisture. A tentative scheme for coal classification was presented at the October, 1932, meeting of the Technical Committee on Scientific Classification, of the American Standards Association Sectional Committee on Coal Classification. This scheme was sponsored by Subcommittee IV on Tentative Classification of Coals, under the chairmanship of W. T. Thom, Jr. It proposed the grouping of coals according to rank by reference to fixed carbon and B.t.u., on the basis of coal containing its natural bed moisture but free from mineral matter. This scheme proposed classifying coals into four broad classes: (1) anthracitic, (2) bituminous, (3) subbituminous, (4) lignitic. The anthracitic class was divided into three groups designated as meta-anthracite, normal anthracite, and semianthracite. The bituminous class also was divided into three groups, low volatile, medium volatile, and high volatile. The high-volatile group was further subdivided into four subgroups according to moisture content, as fo1lows: (1) less than 5 per cent, (2) 5 to 10 per cent, (3) 10 to 15 per cent, and (4) 15 per cent and more. The subbituminous class was divided into two groups, group 1 including subbituminous coals having calorific values of 10,500 B.t.u. or more, and group 2 including those with less than 10,500 B.t.u. The lignitic class of coal was divided into two groups both below 8,000 B.t.u., the one group consisting of consolidated and the other of unconsolidated

Jan 1, 1934

By T. F. Witheree

The Fletcherville Furnace was built in 1864 and 1865, making its first blast from August until October of the latter year, when it was blown out to prevent its " bunging-up." Repairs were made in time to enable it to be blown in again December 12th, 1865, the blast ending October 7th, 1866. Total product 1921.15 tons iron, an average of 6.8.2.5 tons per day, from ores yielding 44.8 per cent. Consumption of charcoal 223.2 bushels per ton of iron. The furnace journal up to this time shows no record of furnace dimensions, or temperature of the blast, but as near as can be ascertained, they were as follows, viz.: Height of stack, 42 feet. Diameter of bosh, 11 feet. Angle of bosh, 71/2 inches to 12 inches rise, about 58°. Diameter of open tunnel head, 42 inches. Number of tuyeres 3 ; each 3 inches in diameter. Dam 15 inches high. Tuyeres 24 inches high. Tymp 224 inches high. Diameter of steam cylinder, 20) inches. } Diameter of blast cylinder, 64 inches. } Stroke 5 feet. The engine is direct-acting horizontal non-condensing. December 26th, 1866, the furnace was again put in blast, having been considerably altered in the crucible; the height of stack, bosh, and tunnel head remaining as before. Six tuyeres were put in, three in each of the side arches. The hearth or crucible was rectangular in form, 3 feet wide x 31/2 feet long x 64 feet high. Inclination of bosh 58°. Height of tuyeres 26 inches; nozzles 21/4 inches diameter. Temperature of blast estimated to be about 500°.