Search Documents

By C. A. Siebert, G. Sandoz

Oil quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State 'A'— Vapor Blanket Cooling—In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage 'B'—Vapor Transport Cooling— Termination of the 'A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage 'C'—Liquid Cooling—The 'B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the 'B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage ' B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 21/2-in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and I-in. stream height, and (2) a 1/2-in. orifice and a 31/2-in. stream height. In all cases the samples were suspended so that the quenched end was 1/2-in. above the orifice. Some tests were run on an NE 8740, .3,312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been Omitted from this paper. The test bars were machined from 1/8-in. stock to I-in. diam by 4 in. long.

Jan 1, 1949

By G. Sandoz, C. A. Siebert

Oil quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State 'A'— Vapor Blanket Cooling—In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage 'B'—Vapor Transport Cooling— Termination of the 'A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage 'C'—Liquid Cooling—The 'B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the 'B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage ' B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 21/2-in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and I-in. stream height, and (2) a 1/2-in. orifice and a 31/2-in. stream height. In all cases the samples were suspended so that the quenched end was 1/2-in. above the orifice. Some tests were run on an NE 8740, .3,312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been Omitted from this paper. The test bars were machined from 1/8-in. stock to I-in. diam by 4 in. long.

Jan 1, 1949

By J. Kent Smith

THE object of this investigation was to ascertain the effect of varying percentages of beryllium upon pure copper and the properties of the resultant alloys in their softest condition, the effect of heat hardening on them, and the extents to which these properties could be augmented by different combinations of heat hardening and cold rolling. The data compiled in this paper represent partial results of continuing work done by the writer during the years 1930 and 1931, which was a continuation of the unpublished ground work incepted in the laboratory of the Beryllium Corporation of America by H. B. Pulsifer in the year 1926. A short bibliography on beryllium alloys is appended to this paper. It has, of course, long been known that copper subjected to cold work is hardened and strengthened to a considerable extent, furthermore it had been qualitatively noted in previous experiments that copper-beryllium alloys seemed to take on hardness and strength as the result of cold work at a greater rate even than does plain copper. It was decided therefore to endeavor quantitatively to determine such rate of increase, as also the relative increases by combinations of cold working and heat hardening. The results are summarized in Tables 3, 4 and 5. A preliminary series of experiments had indicated that by an exposure to the heat of 575° F. for 2 1/2 hr. age-hardening of a 2.50 per cent beryllium-copper alloy took place. Slab ingots of nine different beryllium-copper alloys were prepared under identical conditions by means of the addition of a previously prepared 12.5 per cent beryllium-copper alloy to well melted and deoxidized pure copper. The ingots were then reduced by hot rolling to 12 gage (about 0.080 in.). These strips were heated to 1450° F. and quenched in cold water, and thus brought to their softest condition. (See Table 1.) Strips were next "precipitation-hardened" by reheating to a definite temperature. Similar strips to those itemized in Table 1 (which had been quenched from 1450° F.) were reheated for varying periods of time at 575° F. The hardness figures show that a metastable condition, of which the range of stability is dependent entirely upon time at the given temperature, begins to be noted in copper samples containing as little as 0.85 per cent beryllium. It is extremely noticeable in samples containing

Jan 1, 1932

By G. Sandoz, C. A. Siebert

OIL quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State `A'-Vapor Blanket Cooling-In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage `B'-Vapor Transport Cooling- Termination of the `A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage `C'-Liquid Cooling--The `B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the `B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage `B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 2 ½ -in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and 1-in. stream height, and (2) a ½ -in. orifice and a 3 ½ -in. stream height. In all cases the samples were suspended so that the quenched end was ½ -in. above the orifice. The steel used was an NE 9450 having the following analysis: [ ] Some tests were run on an NE 8740, 3312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been omitted' from this paper. The test bars were machined from 1 1/8 -in. stock to 1-in. diam by 4 in. long.

Jan 1, 1948

By C. W. Macgregor

The observation of the flow layers, or Luders' lines, produced in mild steel when it is stressed into the plastic range often provides considerable useful information for the study of the fundamental mechanism of the plastic flow of metals. It is a commonly observed fact that as soon as the upper yield point in a mild-st'eel tensile-test bar is passed, an unstable condition develops in the equilibrium, the load on the testing machine drops and if the surface of the bar contains a thin mill scale, the latter begins to flake off rapidly along certain "lines." These "lines" are ill reality traces of wedge-shaped flow layers and are formed by the inter-section of the surface of slip and the surface of the bar. The average plane of the flow layer itself has been found by various experimenters to be inclined at an angle of approximately 45" to the axis of the test bar. In a body of more complicated shape stressed in possibly a different man-ncr, the tangent planes to the flow layers at each point seem in many cases to be inclined at an angle of about 45" to the principal stress direct-tions at the point. As examples of the latter may be mentionecl the logarithmic spirals obtained when a rivet hole is punched in a thin plate, or when a tube is subject,ed to internal pressure only, etc. IIencc if the flow layers are observed from an experiment, the shear-st'ress trajectories —the curves indicating the direct,ions of the maximum shearing stresses in the body—may then be approximately determined. Since the latter curves form an orthogonal family inclined at 45" to the principal stress directions, the family of principal stress trajectories, or the curves irldicating the directions of the principal stresses, may be thus obtained Although the discontinuous type of stress-strain curve at the yield point is commonly observed with test bars of mild steel, more recent experiments have shown that this is by no means the only material exhibiting this interesting phenomenon. A similar effect has been observed in zinc and cadmium crystals, by Becker and Orowai~; in duralumin and other aluminum alloys, by Dawidenkow,~Elam,~ Fell4 an(l others; in copper and copper-alloy crystals, by Elam;~ in brass by Elam;3 in brass wires by deForest;" in higher carbon steels, tungsten steel, and

Jan 1, 1939

By C. W. MacGregor

The observation of the flow layers, or Luders' lines, produced in mild steel when it is stressed into the plastic range often provides considerable useful information for the study of the fundamental mechanism of the plastic flow of metals. It is a commonly observed fact that as soon as the upper yield point in a mild-st'eel tensile-test bar is passed, an unstable condition develops in the equilibrium, the load on the testing machine drops and if the surface of the bar contains a thin mill scale, the latter begins to flake off rapidly along certain "lines." These "lines" are ill reality traces of wedge-shaped flow layers and are formed by the inter-section of the surface of slip and the surface of the bar. The average plane of the flow layer itself has been found by various experimenters to be inclined at an angle of approximately 45" to the axis of the test bar. In a body of more complicated shape stressed in possibly a different man-ncr, the tangent planes to the flow layers at each point seem in many cases to be inclined at an angle of about 45" to the principal stress direct-tions at the point. As examples of the latter may be mentionecl the logarithmic spirals obtained when a rivet hole is punched in a thin plate, or when a tube is subject,ed to internal pressure only, etc. IIencc if the flow layers are observed from an experiment, the shear-st'ress trajectories —the curves indicating the direct,ions of the maximum shearing stresses in the body—may then be approximately determined. Since the latter curves form an orthogonal family inclined at 45" to the principal stress directions, the family of principal stress trajectories, or the curves irldicating the directions of the principal stresses, may be thus obtained Although the discontinuous type of stress-strain curve at the yield point is commonly observed with test bars of mild steel, more recent experiments have shown that this is by no means the only material exhibiting this interesting phenomenon. A similar effect has been observed in zinc and cadmium crystals, by Becker and Orowai~; in duralumin and other aluminum alloys, by Dawidenkow,~Elam,~ Fell4 an(l others; in copper and copper-alloy crystals, by Elam;~ in brass by Elam;3 in brass wires by deForest;" in higher carbon steels, tungsten steel, and

Jan 1, 1939

By James K. Gluck, William E. Galloway, Gary E. Smith, John P. Morton, Christopher D. Henry

INTRODUCTION Surface mining and in situ leaching of uranium have the potential to alter ground-water quality around mines and leach sites. Of particular concern is the fate of uranium and its associated trace elements: molybdenum, arsenic, and selenium. We wish to under- stand the natural processes that control trace element concentrations in ground water and how these processes will influence dispersion of the elements from a mineralized zone, both naturally and during and after mining or restoration. For example, it is commonly recognized that the trace elements are soluble in oxidizing ground water but are insoluble, and can be precipitated, in reducing ground water. Thus oxidizing, metal-bearing water leaving a deposit could re- enter reduced ground, causing the water to be re- reduced and the trace elements to be, reprecipitated. In a sense, this is recreating the original mineralization process. To accomplish the above goals, we have (1) examined the theoretical controls of concentrations based on the available geochemical and thermodynamic data, (2) determined the major ion composition and oxidation-reduction status of Oakville waters because of the influence of these factors on trace element solubility, and (3) determined trace element concentrations and distribution in Oakville ground water. The last approach is used to evaluate how well actual behavior follows predicted behavior. This report focuses on two elements, uranium and molybdenum, because they exemplify the results obtained. The report also is restricted to a regional study of Oakville ground water. Results of more de- tailed study in and around major uranium districts in the Oakville and much of the raw data that support the conclusions in this report are presented in Galloway, Henry and Smith (1980). This report is part of that larger study, which concerned the depositional systems, hydrology, and geochemistry of the Oakville. The U.S. Environmental Protection Agency funded the study, under grant numbers R-805357-01 and R-805357-02. Theoretical controls were determined by reviewing the available literature on aqueous chemistry and behavior of uranium and molybdenum. To aid in under- standing water chemistry, Oakville water analyses were run through a modified version of the computer model WATEQF (Plumer, Jones, and Truesdell, 1976). WATEQF calculates speciation of dissolved ions and determines saturation with respect to a variety of minerals. In the discussion below, ion activity products (IAP) are compared with the equilibrium constant (KT) for various reactions and mineral products. Values of log IAP/KT near zero indicate that the water is in equilibrium with a mineral. Values less than -1 indicate considerable undersaturation and values greater than +1 indicate oversaturation. Galloway, Henry, and Smith (1980) give a more complete discussion of the application of this approach to Oakville water chemistry. Eh-pH diagrams have been constructed or adapted from the literature to predict what form -- dissolved ion or stable mineral species -- uranium and molybdenum assume under various conditions. Construction of the diagrams has followed procedures described by Garrels and Christ (1965). This approach is particularly appropriate because the solubility of the elements is Eh-dependent, and Eh varies greatly within the Oakville aquifer. A number of assumptions or approximations are inherent in the use of Eh-pH diagrams and chemical models such as WATEQF and in the interpretation of water chemistry in general. Both Eh-pH diagrams and chemical modeling rely entirely upon available thermo- dynamic data, including free energies of formation and dissociation constants for various reactions. These values are known to varying degrees of accuracy. Most major ions and minerals are relatively well control- led; however, data for trace metals are much poorer. Thermodynamic data are not available for some minerals, and for other minerals, two or more divergent values exist. By necessity, we have relied on the judgment of others to evaluate thermodynamic data. Calculations by WATEQF and constructions of Eh-pH diagrams are based on an assumption of equi1ibrium. Equilibrium may not be comnon in low-temperature aqueous environments; at best, ground-water composi tion may be in a state of dynamic equilibrium, continuously changing due to changes in environmental conditions. Eh-pH diagrams show what phases are stable at equilibrium under given conditions; they do not prove that the phases actually exist. Many minerals persist or form metastably under conditions outside their equilibrium stability field. The kinetics of reactions, which cannot be evaluated here, are important in determining what phases occur. Kinetics may be less of a problem for ground water that travels and evolves slowly through a semihomogeneous matrix than for many other natural systems. Eh-pH diagrams show equilibrium fields only of phases included. They do not indicate anything about stability relative to phases not included in the diagram. WATEQF, obviously, cannot calculate the degree of saturation of a mineral not included in the program or for which the appropriate ions were not analyzed. Thus, a mineral that was not considered may be the most stable phase under a given set of conditions and may control the solubility of a trace element. Also, this study is limited exclusively to in- organic compounds. Organic material is known to be an

Jan 1, 1980

By G. A. Hellstrand

IN 1915, H. A. Guess, Vice President of American Smelting & Refining Co., in charge of its Mining Department, learned that the Anglo-New-foundland Development Co., Ltd., a pulpwood and paper-mill enterprise, had found upon its large concession in Newfoundland, and had opened up by shaft to the third level and some drifting, a lenticular orebody indicat-ing about 100,000 tons, as an extremely fine-grained sulfide ore, averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Cu, 10 per cent Pb, 18 per cent Zn; and that having sent parcels of this ore to Minerals Separation, Ltd., and various other metallurgical testing concerns without obtaining any success in commercial separations thereon, had discontinued work thereon and let the workings fill. Mr. Guess wrote to the general manager of that company and obtained a few hundred pounds of the typical ore, which he sent to his company's metallurgical testing laboratory at Flat River, Mo., outlining various flotation tests desired thereon, in an endeavor to obtain separation into a commercial lead concentrate and a zinc concentrate. But the art of flotation had not then progressed far enough to treat such ore, the galena and zinc blende being so fine grained that grinding to about 300 mesh was required to release the mineral particles in their gangue. Mr. Guess had flotation and other tests continued upon this ore from time to time with whatever new reagents and flotation devices were evolved as time went on, and finally, in 1925, he succeeded in effecting in his company's testing plant, then at Wallace, Idaho, separations into lead concentrates and zinc concentrates of satisfactory commercial grade. Mr. Guess then proceeded to unwater, examine and sample the property and made with the owners a partnership operating agreement upon the mine itself and a considerable area surrounding it, and in the early summer of 1926 began to prospect for additional orebodies, utilizing for such prospecting geophysical methods, under the direction of Hans Lundberg, methods which up to that time had been little used in mining in the western hemisphere.. This geophysical work found two large flat-lying orebodies of a type precisely similar to the smaller body of the original discovery. The larger orebody, some 3500 ft. west of the original

Jan 1, 1934

By John Rogers

The goal of a detailed quantitative understanding of the variables insulfide flotation in terms of established, or new, scientific principles is still distant, although there has been a good beginning in the past 50 years with more rapid progress since 1930. Advances have paralleled closely those in other branches of surface chemistry and the development of a series of experimental techniques such as contact angle, surface area measurement, radioactive tracers, infrared spectra, electron diffraction, monolayer, and electro- chemical methods of investigation. The second editions of books by Sutherland and Warkl ( 1955) and Gaudin2 ( 19571, are detailed accounts of this progress. The complexity of sulfide mineral flotation systems is indicated by Sutherland and Warkl who list 32 variables of flotation, of which only 22 can usually be controlled by the metallurgist. A consequence of this multiplicity of variables, many of which may be specific to each particular ore, is that ways of floating sulfide minerals from new ores are still developed empirically. How- ever, this review will try to show how the chemistry of the function of frothers, collectors, depressants, and activators in sulfide flotation is being steadily unravelled. Chiefly, it will be concerned with the interaction of pure soluble compounds with individual sulfide minerals, the surfaces of which are often not stoichiometric for several reasons discussed by Plaksin.3 As a result, for example, a freshly cleaved galena surface has cathodic and anodic areas which have different degrees of oxidation and different reactivity to- wards collectors like xanthate. Such complicating considerations should be remembered in the subsequent discussion of pure minerals. THE NEED FOR FLOTATION REAGENTS After considerable controversy it has been established with a few exceptions that unoxidized, uncontaminated sulfides will not float. Moreover all flotation plants recovering sulfide minerals use collectors which are removed from the circuit with the sulfides. Gaudin, Miaw, and Spedden4 have discussed the relation between the crystal structure of solids and the native floatability of the exceptions mentioned above. A second question which has been much explored is the nature of the surface on which a collector like xanthate is adsorbed or reacts. Is this the un- changed surface of the sulfide mineral, or does the adsorption depend on the initial oxidation of the sulfide surface ? Sutherland and Warkl and Gaudin2 discuss the work of Taggart5 and others on this question without reaching any other conclusion than that oxygen was important.

Jan 1, 1962

By S. F. Reiter, R. W. Guard, J. H. Keeler

DURING the last several years the authors have been conducting tests on a tensile machine that autographically records load-elongation data. In certain tests at elevated temperatures on face-centered cubic, hexagonal close-packed, and body-centered cubic materials (binary alloys of nickel, zirconium, and iron), the load-elongation curve as shown in Fig. 1 reaches a maximum load (Pmax,) at relatively small amounts of strain and a large amount of elongation occurs subsequently with a continuously decreasing load, until finally localized necking and fracture take place. This early maximum load behavior has been found without the accompanying evidence of localized necking as has been assumed by some, or of evidence of cracking as observed by others.' This behavior has also been observed by Nadai and Manjoinez whose results are in good agreement with ours. The prior strain, strain rate, test temperature, and crystal structure affect the observations. The influence of prior strain was observed in tests on unalloyed zirconium at 300°C in which specimens containing large amounts of prior strain (cold work) exhibited the type of curve shown in Fig. 1. No localized necking was observed after strain as much as that of point B. Annealed and recrystallized specimens of the same material showed a load-elongation curve with maximum load occurring after considerable strain hardening and at the beginning of localized necking. Interrupted tests (Fig. 2) show no loss in strength because of recovery or recrys-tallization during an interval at temperature without load. Recovery under stress such as found by Wood and Suiter3 in aluminum is now being investigated as one possible explanation. The strain rate is a contributing variable as shown in Fig. 3, a test on high purity nickel. Here the strain rate was decreased by a factor of ten during a test in which the maximum load was reached at a small strain. The slope of the true stress-true strain curve was positive with the more rapid strain rate and negative with the slower strain rate. In many binary ferrites an added effect of temperature has been observed. Fig. 4 shows the load-elongation plots for a binary ferritic alloy containing 2 pct Mo. The slope of the small portion of the stress-strain curve obtained at a strain rate of 0.01 mhr1 changes sign from negative to positive on going

Jan 1, 1955

By J. K. Stanley, R. F. Meel

The recrystallization of cold-worked metals is studied ordinarily by determining the temperatures required for complete recrystallization to occur within a given arbitrary time period, usually within 15 min. to 2 hr. The results obtained are conventionally assembled in a three-dimensional diagram relating this temperature to the amount of cold-work (percentage deformation) and the resultant grain size, though sometimes other modes of representation are emp1oyed.l Such three-dimensional diagrams are not complete, for the number of variables exceeds the number represented. The process of recrystallization is characterized by a time-rate, a fact that is not portrayed upon ordinary recrystallization diagrams. It is known that recrystallization consists in the formation of new nuclei and the growth of these nuclei, a process that continues until the matrix is completely consumed and the original set of grains entirely replaced by the new. This knowledge is old.2 Truly heterogeneous reactions invariably proceed by nucleation and growth; the decomposition of eutectoid solid solutions provides an example about which much is known,3 and freezing, originally studied by Tammann, provides the classic example. Although recrystal- lization is not a heterogeneous reaction within the orthodox meaning of the term, the mechanism of the process is the same. As in eutectoid inversion and freezing, it should be possible to study the rate of isothermal recrystallization as a function of time, and it should also be possible to analyze the isothermal reaction curve into the component rates of nucleation and growth that determine them.* Other methods, not employing the rates of nucleation and growth, have been used to represent the rates of such reactions, but these in general have been artificial and have not led to progress. 4,5 The theory of recrystallization is not in advanced state; if recrystallization data were obtained in terms of the rate of isothermal recrystallization, and in terms of the rate of nucleation and the rate of growth of recrystallized grains, and in particular if the temperature coefficients of these rates were measured accurately, an adequate theory should be more readily developed.27 Such an effort requires proper experimental technique, but especially requires suitable methods of mathematical analysis to convert mcasurements made upon a surface of polish into values for the rate of nucleation and the rate of growth and to combine these into a rate of isothermal recrystallization. These methods are now available for the case of three-dimensional recrystallization (recrystallization of

Jan 1, 1942

By R. F. Meel, J. K. Stanley

The recrystallization of cold-worked metals is studied ordinarily by determining the temperatures required for complete recrystallization to occur within a given arbitrary time period, usually within 15 min. to 2 hr. The results obtained are conventionally assembled in a three-dimensional diagram relating this temperature to the amount of cold-work (percentage deformation) and the resultant grain size, though sometimes other modes of representation are emp1oyed.l Such three-dimensional diagrams are not complete, for the number of variables exceeds the number represented. The process of recrystallization is characterized by a time-rate, a fact that is not portrayed upon ordinary recrystallization diagrams. It is known that recrystallization consists in the formation of new nuclei and the growth of these nuclei, a process that continues until the matrix is completely consumed and the original set of grains entirely replaced by the new. This knowledge is old.2 Truly heterogeneous reactions invariably proceed by nucleation and growth; the decomposition of eutectoid solid solutions provides an example about which much is known,3 and freezing, originally studied by Tammann, provides the classic example. Although recrystal- lization is not a heterogeneous reaction within the orthodox meaning of the term, the mechanism of the process is the same. As in eutectoid inversion and freezing, it should be possible to study the rate of isothermal recrystallization as a function of time, and it should also be possible to analyze the isothermal reaction curve into the component rates of nucleation and growth that determine them.* Other methods, not employing the rates of nucleation and growth, have been used to represent the rates of such reactions, but these in general have been artificial and have not led to progress. 4,5 The theory of recrystallization is not in advanced state; if recrystallization data were obtained in terms of the rate of isothermal recrystallization, and in terms of the rate of nucleation and the rate of growth of recrystallized grains, and in particular if the temperature coefficients of these rates were measured accurately, an adequate theory should be more readily developed.27 Such an effort requires proper experimental technique, but especially requires suitable methods of mathematical analysis to convert mcasurements made upon a surface of polish into values for the rate of nucleation and the rate of growth and to combine these into a rate of isothermal recrystallization. These methods are now available for the case of three-dimensional recrystallization (recrystallization of

Jan 1, 1942

By R. F. Mehl, J. K. Stanley

THE recrystallization of cold-worked metals is studied ordinarily by determining the temperatures required for complete recrystallization to occur within a given arbitrary time period, usually within 15 min. to 2 hr. The results obtained are conventionally assembled in a three-dimensional diagram relating this temperature to the amount of cold-work (percentage deformation) and the resultant grain size, though sometimes other modes of representation are employed.1 Such three-dimensional diagrams are not complete, for the number of variables exceeds the number represented. The process of recrystallization is characterized by a time-rate, a fact that is not portrayed upon ordinary recrystallization diagrams. It is known that recrystallization consists in the formation of new nuclei and the growth of these nuclei, a process that continues until the matrix is completely consumed and the original set of grains entirely replaced by the new. This knowledge is old.2 Truly heterogeneous reactions invariably proceed by nucleation and growth; the decomposition of eutectoid solid solutions provides an example about which much is known,3 and freezing, originally studied by Tammann, provides the classic example. Although recrystallization is not a heterogeneous reaction .within the orthodox meaning of the term, the mechanism of the process is the same. As in eutectoid inversion and freezing, it should be possible to study the rate of isothermal recrystallization as a function of time, and it should also be possible to analyze the isothermal reaction curve into the component rates of nucleation and growth that determine them.* Other methods, not employing the rates of nucleation and growth, have been used to represent the rates of such reactions, but these in general have been artificial and have not led to progress.4,5? The theory of recrystallization is not in advanced state; if recrystallization data were obtained, in terms of the rate of isothermal recrystallization, and in terms of the rate of nucleation and the rate of growth of recrystallized grains, and in particular if the temperature coefficients of these rates were measured accurately, an adequate theory should be more readily developed.27 Such an effort requires proper experimental technique, but especially requires suitable methods of mathematical analysis to convert measurements made upon a surface of polish into values for the rate of nucleation and the rate of growth and to combine these into a rate of isothermal recrystallization. These methods are now

Jan 1, 1942

By R. F. Mehl, J. K. Stanley

THE recrystallization of cold-worked metals is studied ordinarily by determining the temperatures required for complete recrystallization to occur within a given arbitrary time period, usually within 15 min. to 2 hr. The results obtained are conventionally assembled in a three-dimensional diagram relating this temperature to the amount of cold-work (percentage deformation) and the resultant grain size, though sometimes other modes of representation are employed.1 Such three-dimensional diagrams are not complete, for the number of variables exceeds the number represented. The process of recrystallization is characterized by a time-rate, a fact that is not portrayed upon ordinary recrystallization diagrams. It is known that recrystallization consists in the formation of new nuclei and the growth of these nuclei, a process that continues until the matrix is completely consumed and the original set of grains entirely replaced by the new. This knowledge is old.2 Truly heterogeneous reactions invariably proceed by nucleation and growth; the decomposition of eutectoid solid solutions provides an example about which much is known,3 and freezing, originally studied by Tammann, provides the classic example. Although recrystallization is not a heterogeneous reaction within the orthodox meaning of the term, the mechanism of the process is the same. As in eutectoid inversion and freezing, it should be possible to study the rate of isothermal recrystallization as a function of time, and it should also be possible to analyze the isothermal reaction curve into the component rates of nucleation and growth that determine them.* Other methods, not employing the rates of nucleation and growth, have been used to represent the rates of such reactions, but these in general have been artificial and have not led to progress .4,5† The theory of recrystallization is not in advanced state; if recrystallization data were obtained in terms of the rate of isothermal recrystallization, and in terms of the rate of nucleation and the rate of growth of recrystallized grains, and in particular if the temperature coefficients of these rates were measured accurately, an adequate theory should be more readily developed .27 Such an effort requires proper experimental technique, but especially requires suitable methods of mathematical analysis to convert measurements made upon a surface of polish into values for the rate of nucleation and the rate of growth and to combine these into a rate of isothermal recrystallization. These methods are now

Jan 1, 1942

By W. F. Mattes

The manufacture of steel rails in the United States upon a large scale may be roughly dated from the years 1875-76, and the same years witnessed an active movement among the railroads toward the adoption of heavier and improved patterns. In this movement each road was a law unto itself, and the "personal equations " of some scores of engineers were so freely injected into the calculations that patterns were multiplied in the most absurd and mischievous manner, until at length the burden upon the mills became wellnigh unendurable, and called forth a vigorous protest in Mr. Holley's paper,* read before the Institute in February, 1881. There were then regularly manufactured in the various mills of the United States, no less than 119 different patterns of steel rails, subject to current order, of which 64 per cent. were embraced under five weights per yard. Commenting upon these and other figures there given, Mr. Holley stated as the primary object of his paper, " to show that,, while this multiplication of rail-patterns is an annoyance and an expense to rail-makers, it is a source of immense loss to railway companies." Since 1876 the increase in gross annual tonnage upon our leading lines has been very great, and has been accompanied by an increase of wheel-loads and running-speeds. As the average weight of the rails of 1876 was by no means excessive, the growing deman Is of traffic have slowly driven the roads toward stiffer sections, inaugurating a movement that now promises to become epidemic. In 1876 a 67-pound rail was a first-class equipment; to-day everything under 75 pounds is light, and many 80's are coming into use. European practice has long been heavier than ours; in part because the higher cost of sleepers has led to an average of 3-feet spacing, instead of two-feet as with us. The old 84-pound double-header, and Sandberg's 80- and 89-pound rails, respectively 51/4 inches and 591/2 inches high, are reported common on English roads; and he is strongly advocating the general adoption of the 100-pounder shown in Fig. 7, with what success I have not learned, except that the Belgian government has ordered a lot. Mr. Sandberg points out the undesirability of frequent changes of pattern, and the recent rapid growth in traffic-requirements; prognosticates a continuance of this

Jan 1, 1887

By G. F. Jr. Butterworth

THE metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to produce in the stock a physical condition having the requisite properties. The first group consists 'of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat-treated by giving it a quench and a draw. These barrels will be referred to as "heat-treated" barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent. of manganese, show a single very pronounced point between 1300° and 1350° F. (704° and 732° C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure discussed below, Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure, shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under- a low magnification appears

Jan 7, 1919

By Charles S. Barrett, Robert F. Mehl, Shueling Woo

WHEN one solid phase is generated from another, fixed and rational orientation relationships are observed to subsist between the parent and the new crystal. The principle has been proposed' that the relationships obtaining between the same two phases are identical whatever the type of phase change involved, or whichever of the phases may act as parent. Many types of phase changes have been studied: allotropic transformations in pure metals, precipitation from solid solutions, eutectoid decompositions, peritectic reactions, the formation of oxide layers, and others.2 Phase layers generated by diffusion of one metal into another constitute an additional type of reaction. This report provides new data on the orientation relationships occurring between , phase layers formed by diffusion, in the Cu-Zn system, § and furnishes further evidence in support of the principle. MATERIALS AND METHODS The Cu-Zn system is especially suitable for these studies since the high vapor pressure of Zn provides an opportunity readily to create one phase poorer in Zn upon a parent phase richer in Zn by removing Zn by vaporization, or to reverse this process by adding Zn from Zn vapor; e.g., the beta phase can be found as a layer upon gamma by dezincing, or gamma can be found on beta by addition of Zn from Zn vapor. Since orientation relationships are to be sought, requiring crystals large enough for orientation determinations, it is convenient to prepare single crystals or large grains of the parent phase. The samples were prepared from oxygen-free high-conductivity copper and Horse Head zinc by melting under a borax flux in a graphite crucible. Large crystals of beta brass were grown by the strain-anneal method, in plates sectioned from the cast ingots, by the following procedure. Rockwell-hardness indents were made at I cm. intervals-and with various loads, then the plates were annealed for .4 days at 700°C. in Nichrome boxes packed with beta-brass chips and graphite. Surface layers were removed by grinding and etching to a depth of about 1.0 mm., and individual grains were cut out. Crystals of alpha and gamma brass were prepared by freezing, by lowering a graphite crucible at speeds less than one inch per hour through a furnace held at a constant temperature above the melting point. Single crystals were cut out with a jeweler's saw, ground, polished and etched. Care was taken to remove cold worked layers from the finished crystals

Jan 1, 1944

By P. W. George, G. A. Hellstrand

In 1915, H. A. Guess, Vice President of American Smelting & Refining Co., in charge of its Mining Department, learned that the Anglo-Newfoundland Development Co., Ltd., a pulpwood and paper-mill enterprise, had found upon its large concession in Newfoundland, and had opened up by shaft to the third level and some drifting, a lenticular orebody indicating about 100,000 tons, as an extremely fine-grained sulfide ore, averaging about 0.05 oz. Au, 4 oz. Ag, 1.5 per cent Cu, 10 per cent Pb, 18 per cent Zn; and that having sent parcels of this ore to Minerals Separation, Ltd., and various other metallurgical testing concerns without obtaining any success in commercial separations thereof, had discontinued work thereon and let the workings fill. Mr. Guess wrote to the general manager of that company and obtained a few hundred pounds of the typical ore, which he sent to his company's metallurgical testing laboratory at Flat River, Mo., outlining various flotation tests desired thereon, in an endeavor to obtain separation into a commercial lead concentrate and a zinc concentrate. But the art of flotation had not then progressed far enough to treat such ore, the galena and zinc blende being so fine grained that grinding to about 300 mesh was required to release the mineral particles in their gangue. Mr. Guess had flotation and other tests continued upon this ore from time to time with whatever new reagents and flotation devices were evolved as time went on, and finally, in 1925, he succeeded in effecting in his company's testing plant, then at Wallace, Idaho, separations into lead concentrates and zinc concentrates of satisfactory commercial grade. Mr. Guess then proceeded to unwater, examine and sample the property and made with the owners a partnership operating agreement upon the mine itself and a considerable area surrounding it, and in the early summer of 1926 began to prospect for additional orebodies, utilizing for such prospecting geophysical methods under the direction of Hans Lundberg, methods which up to that time had been little used in mining in the western hemisphere. This geophysical work found two large flat-lying orebodies of a type precisely similar to the smaller body of the original discovery. The larger orebody, some 3500 ft. west of the original

Jan 1, 1935

By Frank A. Wardlaw

My subject covers the effect that recent metallurgy has had on operations at the Utah-Delaware mine. This mine is the old Highland Boy mine of Bingham Canyon, Utah, one that has now been in operation for about 30 years. It was first operated by Messrs. Weir and Newhouse as a gold mine, under direction of the Highland Boy Gold Mining Co. The ore was oxidized gold ore and it was treated on the property in a cyanida-tion plant. During the process of development, sulfide ore was found assaying about 5 per cent. copper. It proved to be the discovery of what is yet the largest sulfide copper orebody in the State. The first shipment was made in December, 1896. A smelter was built in Salt Lake Valley to treat this ore and not long after the property was sold to the Utah Consolidated Mining Co. From 1900 to 1924, the mine was a large producer of direct-smelting ore which averaged for many years 4.5 per cent. copper, then later dropped to 2 per cent. copper. During the years 1912 to 1920, direet-smelting lead ore was also mined. In 1918 and 1919 ore developments at depth showed a decided increase in silica content and a porphyry sill so closely associated with the ore that it was impossible to mine the ore clean and it was found necessary to build a copper flotation concentrator at Tooele. The mill had a capacity of 1000 tons a day and made a recovery of 90 per cent., and would have been responsible for a continuance of profitable operations had it not been for a slump in the copper market and the necessary high cost of mining ore on the lower levels. Results of Selective Flotation In 1924 the mine was on the point of a shutadown which had all the earmarks of being permanent; it was being operated at a heavy loss and preparations were made to pull the pumps and salvage the machinery. The plant at Tooele was remodelled for selective flotation by the International Smelting Co. in order to treat custom ores, and incidentally to clean up a possible 10,000 tons of lead-zinc ore which it was thought possible to get in the Utah-Delaware before shutting the mine down. Results were so encouraging that an effort was made to develop more lead-

Jan 1, 1928

By J. Kent Smith

The object of this investigation was to ascertain the effect of varying percentages of beryllium upon pure copper and the properties of the resultant alloys in their softest condition, the effect of heat hardening on them, and the extents to which these properties could be augmented by different combinations of heat hardening and cold rolling. The data compiled in this paper represent partial results of continuing work done by the writer during the years 1930 and 1931, which was a continuation of the unpublished ground work incepted in the laboratory of the Beryllium Corporation of America by H. B. Pulsifer in the year 1926. A short bibliography on beryllium alloys is appended to this paper. It has, of course, long been known that copper subjected to cold work is hardened and strengthened to a considerable extent; furthermore it had been qualitatively noted in previous experiments that copper-beryllium alloys seemed to take on hardness and strength as the result of cold work at a greater rate even than does plain copper. It was decided therefore to endeavor quantitatively to determine such rate of increase, as also the relative increases by combinations of cold working and heat hardening. The results are summarized in Tables 3, 4 and 5. A preliminary series of experiments had indicated that by an exposure to the heat of 575" F. for 2 1/2 hr. age-hardening of a 2.50 per cent beryllium-copper alloy took place. Slab ingots of nine different beryllium-copper alloys were prepared under identical conditions by means of the addition of a previously prepared 12.5 per cent beryllium-copper alloy to well melted and deoxidized pure copper. The ingots were then reduced by hot rolling to 12 gage (about 0.080 in.). These strips were heated to 1450" F. and quenched in cold water, and thus brought to their softest condition. (See Table 1.) Strips were next "precipitation-hardened" by reheating to a definite temperature. Similar strips to those itemized in Table 1 (which had been quenched from 1450" F.) were reheated for varying periods of time at 575" F. The hardness figures show that a metastable condition, of which the range of stability is dependent entirely upon time at the given temperature, begins to be noted in copper samples containing as little as 0.85 per cent beryllium. It is extremely noticeable in samples containing

Jan 1, 1932