Search Documents

By W. E. Keck, Paul Jasberg

THERE is a considerable tonnage of iron ore in the Menominee Range of Michigan that is unsalable only because it has too large a content of sulphur. Beneficiation of such ore is economically desirable, as a relatively large quantity of finished concentrate would be obtained (deleterious sulphur mineral content being generally less than 5 per cent) and because large blocks of such ore have been developed incidentally during search for low-sulphur ore. Research on the flotation beiieficiation of these high-sulphur ores consisted of: (1) a study of the flotative properties of the principal minerals in a nearly pure state, (2) flotation of synthetic mixtures of these pure minerals and (3) application of this experimental information to samples of the ores. Gypsum in iron ores is extremely deleterious; but when sufficiently free from impurities it is a valuable commodity. In 1934, the United States produced 1,500,000 tons of calcined and uncalcined gypsum valued at $13,700,0001. Of this quantity and value, Michigan produced approximately 19 per cent4. Thus this investigation may also prove to be of interest in connection with the gypsum industry if minerals separation, such as flotation, becomes necessary in the future processing of gypsum. Data on the flotative properties of gypsum would also be of interest to the science of flotation because such information has been extremely limited. The technical literature reveals one reference to the flotation of gypsum, in which was discussed the use of the mineral, with several others, to determine the relation between the floatability of minerals and the pH of the flotation solution2. This investigation necessarily was not comprehensive in regard to gypsum, but it did show that the mineral could be floated with oleic acid under varying pH conditions.

Jan 1, 1937

By Thomas Fraser, H. F. Yancey

The jig may be termed the standard coal-washing machine. Although exact figures on the relative tonnages of coal treated by the various coal-cleaning processes are not available, it is known that a large part of all the coal given special cleaning treatment is handled by jigs. This wide use of the jig warrants a special study of its performance. In this paper are presented the results of an analysis of work done by a three-compartment jig in treating bituminous coal from the Thick Freeport bed in Allegheny County, Pa. Certain systems of washing coal require sizing before washing, while others treat unsized coal. The prevailing practice, however, for the preparation of coking coal from the more easily washed coal is to treat an unsized or natural feed of about — 1 in. size and smaller. Under such conditions, the minimum size of particle that is beneficiated has long been and is still a matter of discussion and conjecture. In a careful laboratory investigation J?ngstl concluded that the practical limit of settling of fine coal is reached at from 0.02 to 0.008 in. On the other hand, Hancock2 has found that single-compartment jigs, used in preparing coal for the domestic market, usually allow most of the heavy (refuse) particles smaller than 1/4 in. to go into the washed coal. He also states that it is impossible with the ordinary coal jig to make any noticeable improvement in the quality of the coal finer than 20 mesh (about 1/30 in.). Because of its importance in coal cleaning, the work described in this paper was undertaken for the purpose of obtaining information on this subject, as a part of the general coal beneficiation program being carried out by the Bureau of Mines.

Jan 1, 1925

By H. F. Yancey

THE jig may be termed the standard coal-washing machine. Although exact figures on the relative tonnages of coal treated by the various coal-cleaning processes are not available, it is known that a large part of all the coal given special cleaning treatment is handled by jigs. This wide use of the jig warrants a special study of its performance. In this paper are presented the results of an analysis of work done by a three-compartment jig in treating bituminous coal from the Thick Freeport bed in Allegheny County, Pa. Certain systems of washing coal require sizing before washing, while others treat unsized coal. The prevailing practice, however, for the preparation of coking coal from the more easily washed coal is to treat an unsized or natural feed at about -1 in. size and smaller. Under such conditions, the minimum size of particle that is beneficiated has long been and is still a matter of discussion and conjecture. In a careful laboratory investigation Jüngst1 concluded that the practical limit of settling of fine coal is reached at from 0.02 to 0.008 in. On the other hand, Hancock2 has found that single-compartment jigs, used in preparing coal for the domestic market, usually allow most of the heavy (refuse) particles smaller than 1/4 in. to go into the washed coal. He also states that it is impossible with the ordinary coal jig to make any noticeable improvement in the quality of the coal finer than 20 mesh (about 1/30 in.). Because of its importance in coal cleaning, the work described in this paper was undertaken for the purpose of obtaining information on this subject, as a part of the general coal beneficiation program being carried out by the Bureau of Mines.

Jan 4, 1925

By J. Szekely

The paper discusses simultaneous heat conduction and diffusion. These problems may arise in slag-metal kinetics and in connection with rapid heating or cooling of specimens. A mathematical formulation is given and it is shown that the transients due to either the variability of the diffusion coefficient with temperature, or thermal diffusion, are unlikely to be important for molten or solid metals and slags. The negligibility of these effects is due to the large values of the ratio thermal diffu-sivity/molecular diffusivity. In many problems relating to transport-controlled metallurgical kinetics the diffusion process is accompanied by the transfer of heat; large-scale metal refining or metal reduction may be quoted as examples. It has been shown that due to turbulent mixing in these systems the relevant transport phe- nomena are best described in terms of "surface renewal models" which require the solution of the unsteady-state diffusion equation.1-1 Problems involving simultaneous diffusion and heat conduction are also encountered in the laboratory in connection with rapid heating or cooling of specimens. The effect of variable temperature on diffusion may be twofold: a) in the absence of "cross effects" the problem, due to variable temperature, is that of diffusion with a variable diffusion coefficient; b) if the Soret Effect is nonzero, thermal diffusion must also be taken into account in the formulation. Although information is available on thermal-diffusion transients in a steady-temperature gradient,4'5 little work has been done on the effect of unsteady temperatures on either the diffusion coefficient or on thermal diffusion.' In the following a formulation is given and solutions presented with a view of examining the areas where these effects may be important.

Jan 1, 1965

By G. R. Fritterer

Investigators in the field of temperature measurement have long sought a thermoelectric couple fulfilling the following requirements: 1. It should be useful up to and including high industrial temperatures; i. e., 1000 to 1800 C. 2. Its thermoelectric variation with temperature should be linear and be maintained after heating to high temperatures for long periods of time. 3. It should be reproducible; i. e., different couples of the same elements should have similar calibration curves. 4. Its thermoelectric power should be large so as to allow the industrial use of rugged recording instruments. 5. Chemical reactions with, and physical changes within the elements of the couple should not alter its calibration. No thermocouple proposed to date exhibits simultaneously all of these characteristics, whereas the couple about to be described fulfills all requirements to a satisfactory degree. New Thermoelectric Materials A thorough survey of the literature on thermoelectricity revealed that present-day thermocouples could not meet the specifications mentioned above because their thermoelements are metallic. Metals have a marked tendency to deteriorate chemically and their melting points limit their use to low temperatures. Refractory substances, however, are usually resistant to chemical attack and are quite stable at high temperatures. Hence a survey of refractory substances having thermoelectric possibilities was made. One class of thermocouples considered was that in which carbon and a carbide of some metal or nonmetal were the thermoelements. Previous investigators neglected to study this field but certain recommendations were made by them for the use of couples in which carbon served as one element. These proposals are listed in Table 1. The couples suggested are unsatisfactory because of their low thermoelectric powers, the low melting points of their metallic elements, etc. The

Jan 1, 1933

By M. F. Trice

PYROPHYLLITE is a hydrous aluminum silicate (A12Si4O10(OH)2)1 that occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.1 The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey,2 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, "are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. SOURCES At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This

Jan 1, 1940

By C. E. Cannon, R. C. Craze

This paper discusses the results of a study of reservoir pressures in the Gulf Coast area of Texas and Louisiana, showing the general relation of the reservoir pressure to its subsea depth, as well as excessive reservoir pressures that have been encountered. The latter are particularly important in mud-control work, and the data show why it is necessary to use muds having a relatively high density in many of the deeper wells drilled in this area. Only a comparatively few of the wells drilled in the Gulf Coast that have encountered excessive pressures are discussed, but as far as is known those omitted fall within the range of pressure observed by the writers. Measurement of Pressures The following methods were used to determine the values of the original pressures: 1. Estimation of original pressure from subsequent pressure behavior of fields. This method is not precise, and was used only in a few of the older fields in which better methods of obtaining original pressures were not available. Only normal pressures were determined by this method. 2. Measurement of shut-in pressures soon after completion of the first producing well. With one exception, all pressures measured by this method were normal, this well having a pressure slightly higher than normal. 3. Measurements of pressure in connection with drill-stem tests. 4. Estimates from the maximum hydrostatic head of mud that failed to prevent flow from the high-pressure formations into the hole. This method is not exact, tending generally to indicate low pressures. Normal Pressures All pressure measurements available are plotted in Fig. 1, with original pressure at the water-oil contact as abscissa and subsea depth as ordinate. All producing fields fall close to the solid line, which passes through the origin and has a slope of 0.465 lb. per sq. in. per ft. By way of compari-

Jan 1, 1938

By Charles W. Bauer

Most of the aluminum produced in the United States today is derived from foreign bauxite deposits. Earth Sciences, Inc. initiated a program to evaluate domestic non bauxite sources for alumina in the 1960's. In the initial evaluation of alunite, domestic resources were not sufficient to support development. An exploration program led to the discovery of large deposits of alunite in Utah and several other western states. Identification of alunite is difficult as both its physical and chemical characteristics are similar to the minerals with which it is associated. Most of the significant alunite deposits in the western United States are replacement type deposits. These deposits have formed as a result of hydrothermal alteration of volcanic, sub-volcanic, and igneous rocks. Typical alunite deposits contain between 30 and 50% alunite and 50 and 70% quartz, with minor amounts of other minerals. Four mineralogical zones are common in these systems. They include a siliceous zone, a quartz-alunite zone, a kaolinite zone, and a chlorite-montmorillonite zone. Total US reserves of alunite were estimated at 20 Mt fat 30% alunite) by the US Bureau of Mines in 1941. More recent work by the US Geological Survey estimates reserves of 252 Mt and potential resources at 1.4 Gt. Reserves and resources estimated for 23 properties on which field work has been done by ESI are considerably higher. Most of these properties have reserves and potential resources of several hundred million metric tons. The combined demonstrated reserves of these properties are estimated to be about 650 Mt. Inferred reserves are estimated at 2.5 Gt and potential resources at 8 Gt. It appears that the US has sufficient reserves and resources for alunite to be considered as a potential nonbauxite source of alumina.

Jan 1, 1982

By Robert Hunt

The American Institute of Mining and Metallurgical Engineers was the first American technical organization to consider steel-rail specifications and sections. If I am not mistaken, the first contribution on those subjects to the Proceedings of the Institute was presented by Prof. Thomas Egleston, in 1874, and was entitled "Investigations on Iron and Steel Rails made in Europe in the Year 1873.1" The next contribution was Dr. C. B. Dudley's report of his investigation for the Pennsylvania Railroad of the wear of steel rails in their tracks, in 1878, which contribution led to a very memorable discussion that extended through several meetings.2 In 1880, Mr. C. P. Sandberg3 presented an article on rail specifications and inspection and rail sections. This was followed, in 1881, by A. L. Holley,4 in his exhaustive report on the then used American rail sections. The next contribution, I believe, was made by myself' at the Buffalo meeting, in 1888, on steel-rail specifications, which I followed,6 in 1889, by a paper on steel-rail sections. Since that time there have been numerous contributions to the Transactions of the Institute in relation to the manufacture of steel rails. The American Society of Civil Engineers officially took up the investigation of the relation of rail sections to the wear of car wheels in 1888. In the prosecution of this work, the Society appointed a special committee, whose labors extended through several years and resulted in an exhaustive report to the Society in 1893.7 Later, another committee was appointed to consider specifications for the manufacture of steel rails; the labors of this committee extended over a period of several years, a final report8 being made in 1910. It was my fortune to be the secretary of both of those committees.

Jan 9, 1919

By Archer Wheeler

The Boston & Montana Reduction Works at Great Falls, Mont., was formerly the reduction works of the Boston & Montana Consolidated Copper & Silver Mining Co., and continued as the reduction plant for the independent company until .June 1., 1910, when the consolidation of a large number of the operating companies of Butte was effected. It then became merged in the Anaconda Copper Mining Co. as the Boston Montana Reduction Department of the Anaconda Copper Mining Co. The history of copper converting at this plant, while not covering the entire period of the commercial use of the process in this country, does cover by far the larger part of it, and as the operations and appliances of the process have undergone many changes during the time, it may, perhaps, be of some interest to put the record of these changes into permanent form. The plan followed in the preparation of this paper has been to give first a brief chronological record of the principal events and changes and then, even at the risk of some repetitions, to give more detailed account, of some of these changes under separate headings. The headings for the complete paper are as follows: 1. General Chronological Review. 10. Development of Different Classes 2. Mechanical Manipulation of Converters After Class I. 3. Casting of Finished Copper. 11. Basic Lining. 4. Tamping of Linings. 12. Number and Size of Tuyeres. 5. Early Acid Linings. 13. Cast Copper Tuyeres. 6. Acid Linings With the Use of Ore. 14. Efficiency of Air. 7. Introduction of Flux Through the 15. Size of Converter Mouth. Tuyeres 16. Height of Converter. 8. Bottom Blast. 17. Summary. 9. Disposal of Converter Slag.

Jan 8, 1913

By Frederick Rhines

THE investigations of Wyman1 have demonstrated that copper deoxidized with several of the commonly used agents that confer immunity to ordinary hydrogen em-brittlement can still be embrittled if it is annealed alternately under oxidizing and reducing conditions. During the oxidizing cycle, oxygen diffuses into the copper and frequently deposits a subscale composed of the oxide of the residual deoxidizing agent. Upon subsequent reduction with hot hydro-gen, the copper becomes ruptured along the grain boundaries to a depth sharply limited by the previous penetration of oxy-gen as delineated by the inner boundary of the subscale. Obviously the sensitivity to this kind of hydrogen embrittlement is engendered by the introduction of oxygen during the oxi-dizing anneal, but beyond this the mecha-nism of the process, and hence the controlling factors, remain obscure. There are several possibilities: (I) oxygen dissolved in the copper matrix of the subscale may, upon cooling prior to the hydrogen anneal, precipitate as cuprous oxide which is subse-quently reduced by hydrogen as in the familiar case of hydrogen embrittlement; (2) oxygen in solid solution in copper may itself confer susceptibility to embrittlement by hydrogen; (3) the normally refractory oxides such as those of aluminum, silicon and titanium may themselves he reduced by hydrogen when in contact with copper; or (4) the precipitated oxides of the sub-scale may be complex compounds such, perhaps, as Si02-Cu20, which are partially reduced by hydrogen. These possibilities have been examined, and it has been con-cluded that the first three and possibly the fourth are operative collectively or indi-vidually under more or less predictable conditions.

Jan 1, 1940

By John C. Calhoun, F. W. Gooch, J. P. Everett

The results of two sets of displacement experiments are reported. In the first set of experiments various solutions of sugar in water were displaced by other solutions of sugar in water. In the second set oils were displaced by water. Each set of experiments was performed on a linear system made of cemented silica sand grains. These displacement tests were made to evaluate the behavior when the ratio of fluid viscosities between the displacing and displaced phases was varied. A further consequence of the test results is a comparison between displacement behavior when the displaced and displacing phases are miscible as with sugar solutions and when they are immiscible as with oil and water. INTRODUCTION Buckley and Leverett1 have presented a theory for the displacement of oil by gas or water based upon the relative permeability concept. This theory presents the displacement of oil as occurring in two phases, an initial or primary phase preceding the breakthrough of the displacing phase and a subordinate or secondary phase during which both oil and the displacing phase flow simultaneously through the same porous section. These authors gave the results of calculations to show that the percentage of oil displaced during the primary phase by water drive would be dependent upon the ratio of the viscosity of the oil to that of the water. No experimental evidence was reported by these authors to substantiate their theory. Qualitatively, however, it has been found to be in agreement with many observed field results. Laboratory investigators have been in general agreement in reporting for air or gas drive2,3 a small primary phase of production and a large secondary phase. Reported investigations on water drive3,4,5 have shown instances where both primary

Jan 1, 1950

By R. S. McCaffery, R. G. Stephenson

The statistical analysis of blast-furnace data was undertaken to determine some of the relations which exist between the variables involved in furnace operation, and particularly to show the effect of variation of slag composition on such economically important factors as coke consumption, daily tonnage of pig iron and sulfur elimination. It' was desired to correlate the results obtained in commercial practice with those predicted from a study of the quaternary system lime-alumina-silica-magnesia. This paper presents the results of a preliminary study of blast-furnace daily operating reports, and is intended to indicate the suitability of our method of attack and something of the results that may be expected from an extended statistical examination of such data. It has been shown that blast-furnace slags are not composed of oxides, as reported by chemical analysis, but are actually composed of several compounds, each made up of two or more of the oxides present.' These compounds persist in the liquid state, and the properties of a slag are the properties of a mixture of these compounds, and not of a mixture of the ultimate oxides. The oxides lime, alumina, silica and magnesia make up 94 to 96 per cent. of the usual blast-furnace slag, and assuming that we may neglect the remainder of the components, we may determine the minerals present, and their relative proportions, from a study of the quaternary system involving these four oxides. Operating reports from 15 furnaces were available for this investigation. Complete slag analyses for one slag per day were available, per-mittling the calculation of the mineral composition of the slags used. Basic, malleable and foundry irons, with silicon varying from 0.75 to 4.50 per cent. were included in the reports for this examination.

Jan 1, 1931

By J. J. Gilvarry

Recently, Gilvarry1,2 has given a rigorous derivation of the proper distribution function for fragment size in single fracture, based on a closely defined physical model and deduced strictly by the laws of probability. The physical point of departure is Griffith's theory of brittle strength, identifying sub-microscopic flaws as the cause of the low strength of a solid in comparison with values implied by cohesive energies. Gilvarry and Bergstrom,4-7 and Gilvarry8 have compared the predictions of the theory with experiment, and have found excellent agreement, in general. The purpose of this communication is to sketch the extension of the theory to the case of comminution, and to indicate the applications to some examples in nature. The present treatment represents an amplification of a brief discussion appearing elsewhere. 9 Although the basic ideas of the Griffith theory are perfectly general for rupture of brittle solids, it was originally formulated with very brittle materials such as glass in mind. Moreover, Griffith's original experimental work was carried out on glass specimens. Recently, however, the theory has been extended by race" to apply directly to rocks. This extension makes the theory immediately applicable to the materials generally of interest from the standpoint of comminution. GENERAL CASE To obtain the distribution function for fragment size in single fracture, three assumptions are made, that: 1) Fracture proceeds by activation of preex-istent Griffith flaws in the volume, faces, and edges of a fragment; 2) the distributions of flaws of these three types are independent of each other; and 3) activated flaws of a particular type are distributed at random, individually and collectively, in the sense of Fry.11 The last assumption implies that each distribution is separately of Poisson type.

Jan 1, 1964

By C. E. Arnold

A BRIEF description of this installation was included in a recent paper by H. Kenyon Burch.1 The purpose of the present paper is to amplify Mr. Burch's description, as it is felt by the writer that the subject merits more than passing attention. In making a comparison between the common method of hoisting men in mine shafts, and elevator practice in high buildings, the former shows to great disadvantage both as regards safety measures and smoothness of operation. It is surprising that in view of the inducements offered, the step of applying the building equipment direct to the mine shaft has not been taken before, as in many respects the conditions of service are similar, and the objects to be attained are identical. Even without doing this, it is certain that safety to life and limb in the usual method of hoisting men underground can be greatly enhanced by the application to the mine hoist, of some of the features of the building elevator. In the case under consideration, the elevator cage runs in a vertical, concrete-lined shaft compartment 5 ft. 11 in. by 5 ft. 6 in. (1.8 by 1.68:m.) in section and 585 ft. (178 m.) deep, while the counterweight runs in the pipe and ladder compartment of a twin shaft 102 ft. (31 m.) distant. The section of the division of this compartment occupied by the counterweight measures 2 ft. 4 ¼ , in. by 3 ft. 10 ½ in. (0.72 by 1.18 m.), and the counterweight is made in the form of a small cage which. suffices to carry two men for the purpose of making inspections or repairs in the pipe and ladder way.

Jan 12, 1917

By J. Chipman

There is no better way of paying tribute to the memory of a scientist than by developing and carrying forward those ideas which he has contributed to science and which are for us the very essence of his immortality. For a lecturer who has not had the great privilege of stdying under Professor Howe or 'ven of knowing him in person, these ideas must be transmitted through the printed word. It is our great good fortune that Professor Howe left to us a rich heritage of publication, not only in his classic monograph on the "Metallography of Steel and Cast Iron" but in a wealth of earlier hooks and papers in the transactions of this Institute arid of other scientific and engineering bodies. An outstanding characteristic of this published record is the great breadth of interest and of vision which it portrays. His was riot a narrow specialization in only the scientific aspects of ferrous metallographg. On the contra1y many of his important contributions had to do with a far broader field of metallurgicial endeavor. He insisted that his students be well grounded in 1 he fundamentals underlying the whole field and not led into the narrow groove of specific applications. Among his first major publications we find papers on copper smelting, extraction of nickel, the efficiency of fans and blowers, thermic curves of blast furnaces, the cost, of coke, and the manufacture of steel. These are the papers of a metalhurgical engineer and it was among engineers that Henry Marion Howe made his early and well-merited reputation. These early engineering contributions display very clearly the strongly sctientific inclination of their author. The classic work on "The Metallurgy of Steel" published in 1890 contains a thorough and critical discussion of all that was known at the time concerning the alloys of iron and of what we would now call the physical metallurgy of steel. In addition it describes steel-making processes in use and some that had become obsolete, and points out in critical fashion the reasons for success and failure. Steel mill design and layout were included as well as some pertinent discussion of refractories. The book is indeed an embodiment of one of Howe's outstanding characteristics—breadth. It is both the science and the engineering of steel production as known in that day. One of Howe's earliest technical papers was entitled "What is Steel?" That was nearly seventy-five years ago when many new processes and new kinds of steel were being developed. The time was ripe for such a question and the answers which Howe was able to give were helpful in understanding the phenomena of heat treatment. Twenty-five years ago Professor Sauveur repeated the question as the title of the first Henry Marion Howe Memorial Lecture. It seemed to him that this question, "What is Steel?," had served as Howe's motto throughout the remainder of his life. Today I shall present for your consideration a question of another sort: "What is Sletallurgy?" Perhaps it is not too much to hope that in the answer we may obtain a clearer and possibly broader view of the nature of our science and our profession. The time is ripe for giving careful consideration to what we mean by metallurgy. If our Metals Branch is to become in fact an American institute of Metallurgical Engineers, it is essential that we understand what is meant by metallurgical engineering. I am convinced that the best interests of the profession have not been served by a narrow interpretation of these terms. We must now place emphasis on the breadth of metallurgy as a science and as an engineering profession. With its usual brevity and wit. Webster's dictionary definesmetallurgy as "the science and art of extracting metals from their ores, refining them and preparing them for use." I shall riot assume that the words "science" and "art" and "metal" are so well understood as to require no defining but others among our contemporaries are better qualified than either your lecturer or the dictionary to present the broad meanings of these terms. When we say that metallurgy is among the oldest of the arts we are not classing it with painting or sculpture or music but rather with the making of tools or weapons or the building of bridges or chariots or cathedrals. In short we are saying that metallurgy is among the oldest of the engineering professions. The question " What is metallurg ? " has been one of rather more than ordinary concern to those of us who have the task of developing a curriculum for the education of students in this field. This development has been going on in a number of universities over a period of some years. but there seems to be as yet no unanimity as to what such a curriculum should contain. I believe there is fairly complete agreement that it must be founded upon sound

Jan 1, 1950

By N. Nakanishi, C. M. Wayman

The effect of small copper additions on the mar-tensitic transformation behavior in Au-47.5 at. pct Cd was studied by measuring electrical resistivity as a function of temperature. The transformation behavior was found to change and transformation start (M,) temperatures for both the ß to ß' and ß to ß' transformations were depressed substantially by the addition of small amounts of copper. Both M, temperatures were lowered approximately 70°C per at. pct Cu. Copper also had the effect of narrowing the transformation hysteresis region (resistivity us temperature), and for the alloy Au-47.5 Cd-1.5 Cu there was little or no hysteresis; in this alloy, the reverse transfmmation upon heating apparently occurs below the thermodynamic equilibrium temperature, To. THE ß phase in the Au-Cd system occurs at the electron/atom ratio 3/2, and is similar to other ß phases in alloys based on copper, silver, or gold. It is of the CsCl type, in which a considerable degree of long-range order persists to the melting temperature.' The phase boundaries of the ß phase are not known precisely below 300° C, but at room tem- perature the phase exists from approximately 46 to 52* at. pct Cd.2 At low temperatures, the ß phase transforms in a diffusionless (martensitic) manner. Alloys having a composition near 47.5 pct Cd transform upon slow cooling to an orthorhombic3 phase, ß', at - 60°C. Alloys having a composition near 49.0 pct Cd, transform at - 30°C into a phase, ß", which has been recently identified as trigonal.4 Alloys having compositions near 48.5 pct Cd will transform into both the 0' and 0" phases over a range of temperatures. The progress of transformations can be observed

Jan 1, 1963

By A. J. Strauss

The solubilily of lead in PbS as a funclion of lemperature has been investigated by means of Hall coej'icient (RH) measurentents OIL samples prepared by annealing and quenching Bridgman-grourz single crystals, which contain excess lead incorporated during /heir growth from the mell. For sufficiently long annealing times and sufficiently rapid quench rules, the samples obtained consist of n-lybe PbS snturated with In the semiconducting compounds PbS, PbSe, and PbTe, the point defects associated with the presence of lead in excess of the stoichio metric composition are shallow donors. The defects associated with the presence of excess nonmetal are shallow acceptors. lead at the annealing teuiperatiire, together luilh a dispersed second phase of lead microprecipitates. Due to the retrograde solubility of lead, the measured free carrier concentration (n = l/eR77) decreases with decreasing annealing tewperature (T) from- 2.4 X 10 em-3 for 1l85OK to 1.3 X 1018 cm-3 for 623°K. The dala are well-represented by the equation n =(1.08 x 102) exp[ - (0.37 ev.)/kT] cm-3 For most undoped samples of these compounds, the carrier concentration at room temperature and below is determined primarily by the stoichiometry, since the concentration of either excess lead or excess non-metal is large compared to the concentrations of intrinsic carriers and electrically active impurities. Therefore the dependence of composition in temperature and partial pressure can be investigated by means of Hall coefficient measurements, even though the deviations from stoichiometry do not exceed 0.03 at. Pct

Jan 1, 1968

By T. S. Fuller

Various phases of the embrittlement of solid copper containing oxygen by the action of reducing gases at high temperatures are familiar to readers of metallurgical literature through the work of many experimenters. In 1900, Heynl recorded observations of copper being heated in hydrogen with the development of fine cracks, the result of the formation of steam within the metal through the action of hydrogen on the copper oxide usually found in copper. Archbutt,2 in 1905, published the results of experiments, showing that all oxygen can be removed from copper by heating to redness, for several hours, in hydrogen. Intercrystalline cracks and extreme brittle-ness developed. Archbutt attributed the brittleness to the reduction of oxides present in the copper. Bengough and Hil1,3 in 1910, encountered the now well-known embrittlement at the outset of their investigation and stated in their paper: It soon became evident that the effect of any heat treatment depended largely on the presence or absence of reducing gases in the atmosphere of the furnace, as well as on its temperature. Hence it became necessary to adopt a somewhat elaborate scheme of heat treatment. The authors found embrittlement in separate experiments due to both hydrogen and carbon monoxide and concluded that: "The gases ruin the alloys after being heated to about 650" C. in their presence." Ruder,4 in 1916, reported the results of a series of experiments made by heating commercial and deoxidized copper in hydrogen, carbon monoxide, carbon dioxide, and steam. In agreement with other writers, he found that copper containing oxygen was made brittle by reducing gases, while the deoxidized metal remained unaffected. In the case of

Jan 1, 1926

By Franz Wever

ACCORDING to Tammann,1 the explanation of the effect of mechanical deformation in producing changes in the properties of metals is one of the most important problems of physical metallurgy, taking rank with the study of the constitution of alloy systems; and this problem has long attracted-the attention of practitioner and scientist alike. Its solution was not advanced materially until Tammann2 set up his translation hypothesis with its crystallographic basis, while other hypotheses, such as the amorphous metal hypothesis of Beilby3 and Rosenhain,4 have been shown by more intensive studies to be less and less satisfactory. The principles of the Tammann translation hypothesis have proved to be useful even up to today and in spite of all of the recent accumulation of experimental data, while the differences of opinion which have arisen relate to the extent to which the hypothesis accounts for the observed changes in properties and to what extent further assumptions are necessary. Stimulated by the proposals of Tammann, there soon developed a lively experimental activity which aimed at the elucidation of the structural or crystallographic changes produced by the mechanical deformation of metals. Parallel movements of crystal "blocks" along definite crystal slip planes had already been observed by lowing and Rosenhain5 in 1900, in metals which had been moderately deformed but without shedding light on the crystallographic nature of the processes accompanying more severe deformation. The solution of this important problem was not advanced until a much later date, or until the methods of X-ray crystal analysis had become available. Shortly after the discovery of the diffraction of X-ray by crystals, symmetrical diffraction effects were

Jan 1, 1931