Search Documents

By William C. Hagel

Oxygen-18 exchange between gaseous oxygen, held at a pressure of 125 mm Hg in a PL-IORh chamber, and splzeres of a Fe2O3 containing three or less grains was determined from 9000 to 1250°C. Isotope equilibrum on crystal surfaces appears to be quickly established, and the rate-determining factor is self-difiusion confbvrning to the relation D = 2.04 esp(- 77,900/RT) sq cin sec-'. Changing sphere diameters caused no detectable variation in diffusion coefficients. Oxygen ions diffuse faster than cations at low temperatures, but a crossover may occur at about 1150°C. INVESTIGATIONS by Davies et al.' and Himmel et al2 have suggested that the mechanism of iron oxidation above 600°C involves a predominance of cation migration in the wüstite (FeO) and magnetite (Fe301) layers and oxygen-ion migration in the hematite (a Fe2O3) layer. Evidence for little cation migration during hematite growth consists of: 1) the disappearance of radioactive-silver markers, presumed to vaporize from the oxide-gas interface, and 2) a large discrepancy between parabolic rate constants for magnetite oxidation and those calculated from Lindner's3 data for cation self-diffusion, D:, using Wagner's theory.4 Reversing the calculations gave anticipated self-diffusion coefficients, D:, for oxygen ions of 3.6 x 10-9 sq cm sec-1 at 1100°C and 5.9 x 10-10 sq cm sec-1 at 1000°C. Since then Kingery et a1.5 reported three values for oxygen-ion diffusion in polycrystalline, sintered hematite. These were obtained near 1200°C, at an oxygen pressure of approximately 150 mm Hg, and could be represented by the Arrhenius expression, Dg = 1 x 10 11 exp(-146,000/RT) sq cm sec-1. Extrapolation to temperatures below 1100°C infers that oxygen ions are less mobile than cations. This contradicts the aforementioned oxidation evidence and also coble7s study of the initial sintering of hematite. From the latter, apparent diffusion coefficients for the slowest rate-controlling species could be calculated, and fair agreement was found with an extension of Lindner's data for cation diffusion. Fig. 1 depicts such comparisons graphically. Three points have been included for the determinations of Himmel et al. on cation diffusion in large, natural hematite crystals surrounded by pure oxygen at atmospheric pressure. No dependence on crystal log raphic direction was noted. Since the value of 10-l4 sq cm sec-' at 1000°C actually represents an upper limit, one might interpret that there is a small decrease in D: when single crystals are employed. On the whole, however, cation diffusion appears relatively well-defined,* while the few results tension to lower temperatures. After having gained experience measuring oxygen-ion diffusion in certain glasses7 and in the corundum oxide, a Cr2O3, the purpose of this work was to determine D; values for hematite and thus possibly assist a mechanistic understanding of the kinetics of the oxidation and reduction of solid iron oxides. I) EXPERIMENTAL PROCEDURE A) Material. Hematite powder of moderately high purity was received from the Columbian Carbon Co. An accompanying lot analysis listed 0.03 H2O, 0.008 weight percents, with the remainder Fe2O3. Subsequent treatments were ball milling, drying, prepressing, and hot-pressing for 60 min at 1350°C under 5000 psi. Since graphite dies coated with a slurry of alumina were used for hot-pressing, the surrounding atmosphere at temperature was sufficiently reducing to form some magnetite on the outer surface of each cylinder. After removing any attached alumina, a stabilizing anneal of 50 hr at 1300°C in oxygen was added. The final product was nonmagnetic and exceeded 97 pct of the density (5.24 g cm-3) usually given for FezO3. On polishing cylindrical ends, counts were made of the number of grain boundary intercepts per

Jan 1, 1967

By Eric Jette

THE results of an investigation of the ternary system iron-chromium-ilicon were reported in 1936 by the present authors.1 Partly for the sake of theoretical interest, and partly because of the possible commercial importance of these alloys, the present investigation was undertaken to determine the effect of some of the commoner elements likely to occur, deliberately or otherwise, in such alloys if made on a commercial scale. The elements thus added were carbon, nickel or manganese. The alloys studied were, therefore, parts of quaternary systems. This investigation was concerned primarily with the effect of these additional elements on .the alpha-iron phase and the boundary between this phase region and the alpha plus sigma two-phase region. The sigma phase is a ternary solid solution based upon the compound FeCr. The work was performed mainly by X-ray methods, but a number of microscopic examinations were also made and are reported. While isolated alloys in the composition ranges studied may have been discussed in metallurgical publications, no systematic investigation of any assistance to us was found. Of the earlier work, the investigations on the iron-chromium-carbon system and on the chromium carbides by Westgren and his coworkers,2,3 enabled us to identify the carbide phase. Several articles appeared after the present experimental work had been completed. Lucas and Wintrup4 determined the solubility of carbon ill molten iron-chromium-silicon alloys. Tofaute and his coworkers5,6 have made detailed studies of the iron-chromium-carbon system, which will he referred to later.

Jan 1, 1937

By William Fink

THE investigation of aluminum alloy systems prior to 1923 was severely handicapped by the low purity of the best aluminum available. However, by that time, the electrolytic purification of aluminum had been developed by the Aluminum Company of America,(1)? and in May, 1923, there was initiated, under the direction of E. H. Dix, Jr.,(2) a program for the investigation of the aluminum-alloy systems using the purest electrolytically refined aluminum. Up to the present time 15 papers (a) have been published, most of which are on the binary aluminum systems. Work is now in progress on the ternary systems, and it seems probable that most of the future work will be on ternary systems. Therefore this survey of the binary aluminum systems investigated up to the present time (the sixteenth paper of the series) concludes the first phase of this program. Certain qualitative relations between corresponding portions of the various binary diagrams as well as between different parts of the same diagram were noted some time ago by R. S. Archer.(4) In the present . paper these relations and others are considered quantitatively by the application of well-known thermodynamic equations or by newly discovered empirical relations No attempt will be made here to present the history of the develop-ment of the thermodynamic equations defining equilibrium or their application to metallic systems, although a list of references is given at the end of this paper for those who are interested in this phase of the

Jan 1, 1934

By Ralph Arnold

IN OPENING the symposium under the auspices of the Petroleum and Gas Committee of the American Institute of Mining and Metallurgical Engineers, I wish to call to your attention the following, among other subjects, which it is hoped may receive proper attention: 1. The recording of as accurate an appraisal of the oil possibilities of the various countries as is possible, with information as to the immediate availability of their supply. 2. The development of further support for the move-ment to bring about active cooperation among Ameri-can oil companies in their foreign exploration and development work. 3. The furtherance of the efforts of the industry in securing governmental assistance in foreign oil develop-ment: (a) along the lines of a modification of our domestic oil policy, so that we can go to foreign coun-tries and consistently ask fair treatment as to royalties and bonuses; (b) by a closer cooperation between the State and Commerce Departments and the oil industry. 4. The calling of attention to the unjustifiably drastic action of the price-fixing group of the oil industry during the last year or so, with the hope that it will use gentler methods in the future. None of these subjects are new, and some of them have been discussed before various organizations for years. Our justification for again bringing them forward is the hope that by everlastingly harping on them the industry, the Government, and the people who shape the destinies of this country may some time, some how, realize their importance and take effective constructive action.

Jan 6, 1922

By Ken-ichi Hirano, B. L. Averbach, Morris Cohen, N. Ujiiye

The influence of plastic deformation in compression on the self-diffisivity of a iron has been measured in the temperature range of 742º to 885°C. The diffusivity is enhanced in proportion to the strain rate, but this dependence decreases with increasing temperature. The magnitude of the strain is relatively unimportant in this connection. Strain rates from 0 to -2 x 10-3 sec-1 were investigated, with a corresponding increase in diffusivity up to 3 x 103 times. The results are analyzed in terms of vacancy diffusion and the excess vacancies introduced during dejornzntion. It is concluded that grain boundaries are the main vacancy sinks in polycrystalline iron and that the vacancy lifetime is therefore dependent on the grain size. A typical vacancy lifetime at 800°C with a nzean grain-boundary intercept of 0.3 cm is of the order of 1 sec. LATTICE imperfections are considered to be the dominant mechanism of diffusion in close-packed crystals. Vacant lattice sites are usually the most important defect, but the enhancement of diffusion along grain boundaries and other short-circuiting paths has been well documented. Inasmuch as plastic straining produces a variety of defects, it would be expected that the application of stresses sufficient to cause plastic flow during a diffusion run might result in an increase in the self-diffusivity. Enhanced self-diffusion in a iron under compressive creep has been observed by Buffington and Cohen' and subsequent coworkers.2 Lee and Maddin3,4 have also found an enhancement in the self-diffusivity of silver single crystals undergoing torsional deformation. On the other hand, Darby, Tomizuka, and Balluffi5 have not observed any significant diffusion increase in single crystals of silver deformed either in tension or in compression, although the results in this case may have been affected by the occurrence of recrystallization. With poly crystalline silver, however, Forestieri and Girifalco6 have found en- hanced diffusion during compressive creep. A small decrease in the self-diffusivity of zinc single crystals under compressive loading has been reported,7 but the applied stresses in these experiments were too low to cause appreciable plastic deformation. For the cases in which enhanced diffusion has been found, a number of common effects have been noted. Usually, the ratio of the diffusivity during straining, Ds, to the diffusivity in the unstrained condition, D,, varies linearly with the strain rate, and does not seem to be a function of the plastic strain, at least up to ? = 0.2. Values of Ds/Du of the order of 100 have been reported'-4 but the enhancement decreases with increasing diffusion temperature. The activation energy for diffusion decreases markedly with increasing strain rate and approaches a level of roughly one-half the unstrained value. Most of the current explanations of these observations assume that excess vacancies are generated by the deformation, but rather large concentrations of excess vacancies and/or long lifetimes are required by these theories.',',',' Since the original work on iron, there has been an important improvement in the compressive-loading technique.2 The early data were also analyzed without taking into account the motion of the coordinate system in the specimens undergoing plastic deformation. This problem has now been solved by a number of investigators (see Refs. 11, 12, and the appendix of the present paper). Consequently, the strain-diffusion runs on iron for the Ds measurements were repeated and extended over wider ranges of temperature and strain rate. In addition, the original diffusivity data9 on the unstrained iron have been corrected for the divergence of the beam in the counting system and new data points have been added, resulting in somewhat different values for the self-diffusi-vities in a iron.10 The new values for Du are used in this paper. A comparison of Ds and Du confirms the large enhancement in the self-diffusivity of iron during compressive creep, as previously reported.',2

Jan 1, 1963

By Joseph Daniels

The Fritz Engineering Laboratory was built under the direction of John Fritz, and presented by him to the University. A view of the building, looking east, is shown in Fig. 1. The building was started in 1909, and completed in 1910, although all of the equipment was not placed until later. Mr. Fritz gave his personal attention to the details of construction and equipment, and it was his custom to drive over every day to the University from his home in Bethlehem and spend some hours watching the work, offering suggestions, making changes, and planning new work. The result is a building and an equipment which embody his practical ideas. The laboratory structure is of the steel mill-building type, of light-colored brick, 91 by 114 ft., of which a section is shown in Fig. 2 and the floor-plan in Fig. 3. The steel frame carries the roof and traveling crane-way. Ample light has been provided by numerous windows in the side and end walls, in the clerestory, and by a skylight 84 ft. long and 9 ft. wide in the north roof. The main aisle of the building is 49 ft. 2 in. between centers of crane-columns, and has a clear height of 40 ft. The remainder of the width is taken up by two side aisles, 18 ft. high. The laboratory consists of four sections: (1) A general testing-section containing the testing-machinery, a small machine shop, and an office; (2) a cement-testing room; (3) a room for making and storing concrete test-specimens; (4) a hydraulic section.

Jan 1, 1912

By R. E. Smallman, J. C. Terry

J. C. Terry and R. E. Smallman (Llniuersity of Birmingham, England)—In a recent publication53 Wood and Westbrook have reported the results of an investigation of the tensile behavior of fl-phase AgMg alloys. These results agree in broad outline, but differ in the details, with those obtained in the above laboratory and, consequently, some discussion of their paper would seem appropriate. In our experiments, tests were carried out on extruded wires, 2 mm diam, in a hard-beam tensile machine, and while an oil bath was used for the tests up to 150°C, above this temperature the oil bath gave rise to serious contamination of the specimens and hence tests above 150°C were made in vacuo. This procedure is different to that adopted by Wood and Westbrook. The ß-phase alloys exhibit differences in mechanical behavior when they are tested in different temperature ranges. In agreement with Wood and Westbrook, three characteristic ranges are observed which may be classified as low, intermediate, and high temperatures, respectively. Our experiments show that in the low-temperature region, the shape of the stress-strain curves is similar to that reported. However, in addition, it is observed that the temperature at which the low-temperature region ends is markedly dependent on strain rate, and increase with increasing strain rate as shown in Fig. 18. The temperature at which a transition from the low to the intermediate temperature takes place is about 0.4 to 0.45 of the absolute melting point, Tm. This transition temperature coincides with that at

Jan 1, 1963

By Luiz C. Correa da Silva, Robert F. Mehl

A. D. Le Claire and R. S. Barnes (Atomic Energy Research Establishment, Harwell, Didcot, Berks., England)-—This much awaited paper admirably confirms that the Kirkendall effect is a true diffusion phenomenon and likely to be found in all diffusing systems. The most likely explanation put forward so far to account for the shift of interface is that the two components of the system, diffusing in opposite directions, do so with unequal rates so that there is a net loss of material from that half of the diffusion zone rich in the more rapidly diffusing component. This loss is accompanied, and at least partly compensated for, by a closing up or decrease in volume of this latter half of the diffusion zone and an expansion of the other half so as to tend to keep constant the overall volume per atom. This is manifest as a movement of the original interface. If this is a true picture of what is taking place then there are at least two important matters requiring further study."1—The quantitative relating of the observed shift with the independently measured separate diffusion coefficients of the two diffusing species."2—A detailed study of the mechanism and characteristics of the closing up process."We would like first to make a few remarks pertinent to these topics. In connection with the first of these, it is a pity that more and detailed measurements were not made on the Au-Ag system, the only one for which the separate diffusion coefficients of the two species have been measured.'" One of us (A. D. Le C.) has calculated from Johnson's results the shift to have been expected in samples D.2 and D.3. Darken4 showed that the velocity v with which the markers move is related to the separate diffusion coefficients Dau, Dag, by the eauation:"dN"v = (Dag — Dau "dx"dN"where .is the concentration gradient at the mark-ax"ers. Under certain conditions,4, 20 it can also be shown that:"Xm"v = "2t"where x, is the total marker shift after time, t:"dN". . xm = 2t (Dag — Dau) [9]"dX"Johnson measured Dag and DAu in a chemically homogeneous alloy and so his reported figures represent the true or ideal diffusion coefficients"; the same quantities in eq 9 represent the actual diffusion coefficients as would be measured in the presence of a chemical concentration gradient, so we need to multiply Johnson's reported values of Dag and Dau by the"1 before insert-dlogN "ing them in eq 9. 7 is the activity coefficient of Ag at the concentration prevailing near the markers which we shall assume to be - 50 pct. The values of the thermodynamic factor for N = 0.5 and the temperatures at which D.2 and D.3 were annealed were obtained from thermodynamic data quoted by Darken.' aN/ax was computed from the coefficient of inter-diffusion of Au and Ag given by Johnson on the assumption that in the samples D.2 and D.3, the concentration distance curve could be represented by the standard equation:""No is the original difference in concentration between the two halves of the couple, and + is the error or probability function."aN/ax at x = 0 is then given by:"adN/dx "2/nDt"and we assume that this represents the concentration gradient at the markers, although it is probable that the figure is slightly high."When all the appropriate quantities are inserted in eq 9, we find that the expected shifts are: for D.2, 0.0134 cm and for D.3, 0.0119 cm."The agreement between these results and those

Jan 1, 1952

By P. Gordon, A. S. Iyer

IN a paper on the mechanical behavior of heat-treated steel, N. H. Polakowski' put forward arguments to the effect that the stored energy resulting from the deformation of metals should be reduced during the inital stages of subsequent deformation carried out under conditions which produce work softening. At the time (1957) the only energy measurements available as indirect evidence on this point were the results of M. M. Degtyarev,2 some of which Polakowski reproduced in his Fig. 6, and which are again reproduced here in Fig. 1. The solid lines in the upper part of Fig. 1 are Degtyarev's, the dashed Lines Polakowski's prediction of the true trend of the stored energy in copper samples pre-strained in tension and then given various amounts of subsequent compression. The accuracy of this prediction has been borne out by some experiments carried out on American Smelting and Refining Co. copper (99.999' percent Cu) by the present authors. Bars of this copper about 0.4 in. in diam and 12 in. long were prepared by vacuum melting and casting, followed by cold forging and swaging in several stages of about 40 pct reduction in area with intermediate recrystallization anneals. After the final anneal one bar was deformed in tension to 30 pct elongation; the gage length was then cut into several samples which were given axial compressions of various amounts. The hardness of

Jan 1, 1960

By Charles Y. Clayton

A study of the literature shows that the greater part of research work on annealing of cold-worked iron has been for the purpose of studying the effect on grain-size and properties other than hardness. No reference has been found of experimental work of the same nature as that explained in this short paper. The material used throughout was Vismera iron, an iron containing 0.03 carbon and made several years ago by the Inland Steel Co. One-half inch stock was cut into cylinders % in. long. The cylinders were then compressed for 60 sec. in a Reihle testing machine under loads as indicated below: CoMPressiON, Average Length, Series Pounds Inches 1 10,000 0.693 2 15,000 .599 3 20,000 .501 4 25,000 .426 5 30,000 .378 6 35,000 .351 7 40,000 .311 Fig. 1 shows these cylinders after compression. Each series consisted of 17 specimens lettered 0, B, C, D, E, F, G, H, I, J, K, L, M, N, P, Q and R. One specimen of each series was reserved for study of the properties in the cold-worked condition. The other specimens were annealed in a Hump furnace for 1/2 hr. at the following temperatures: TEmpeRa- TempeRa- Letters tuRe,° C. LettERs tuRe °C. B............................... 250 J.............................. 650 C............................... 300 K............................. 700 D............................... 350 L.............................. 750 E............................... 400 M............................. 800 F................................ 450 N............................. 851 G............................... 500 0. . :........................... 900 H............................... 550 P.............................. 950 I................................ 600 Q............................. L000

Jan 1, 1926

By P. M. Budge, William L. Fink, Kent R. Van Horn

The investigation of the phase relations of high-purity aluminum-base alloys is a part of the fundamental research program of the laboratories of the Aluminum Company of America. The results of a number of binary and ternary systems have previously been published in the Transactions of this society. The aluminum end of the binary aluminum-titanium system has been studied. This system has received relatively little attention. To the authors' knowledge, there are two previous papers on this subject. E. van Erckelensl determined the constitutional diagram reproduced in Fig. 1. According to this diagram, the liquidus represents the separation of TiA14, (Ti = 30.7 per cent.). He concluded that this is the composition of the compound, because in his work the eutectic horizontal terminated at 30.7 per cent. titanium and the metallographic examinalion of a sample of this composition revealed only one phase. According to the constitutional diagram developed by W. Manchot and A. Leber,² reproduced in Fig. 2 from data given in their article, the liquidus represents the separation of the compound TiA13 (Ti = 37.2 per cent. ). The composition of the compound was derived in a manner similar to that utilized by van Erckelens. Moreover, Manchot and Leber confirmed the composition of the compound by analysis of the constituent left as a residue after dissolving the alloys in weak sodium hydroxide solution. Although these are the only publications describing the constitution of the system, other investigators have studied the composition of the titanium compound. L. WÖhler3 says that there is a compound TiA13 which was later confirmed by W. Manchot and P. Richter4 and by

Jan 1, 1931

By Robert D. Pehlke, Weldon L. Daines

The reduction of manganese oxide from a basic slag by silicon dissolved in liquid iron at steelmaking temperatures was studied to determine the rate-controlling step for the process. The experiments were carried out under an argon atmosphere in a resistance-heated vertical-tube furnace. The two liquid phases, slag and metal, were held in zirconia crucibles. Sampling and chemical analysis of the slag phase led to time-concentration curves for the system. Results obtained by varying parameters such as temperature, stirring rate, concentration, and melt geometry defined the limiting reaction mechanism. The reduction of manganese oxide by silicon is a fast reaction and reached equilibrium within 90 min. The rate of stirring has a marked effect on the reaction rate, while, on the other hand, the effect of temperature is very small. This identifies the rate-controlling step as diffusion rather than interfaciul chemical reaction. The variation of other parameters revealed that a) diffusion of manganese in the iron phase is the slow step, b) the value of D/6 for manganese in iron at 1550°C is 7x 10-4 cm per sec, c) the energy of activation for the apparent rate constant is 7 kcal per mole, and d) increasing the amount of silicon in the iron decreases the diffusion coefficient of manganese. THE equilibrium relations pertinent to the reduction of manganese oxide from a steelmaking slag by silicon dissolved in liquid iron have been studied, but little is known about the mechanisms that control the rate of the process. The purpose of the present investigation was to study the rate of reduction by silicon and to determine the rate-limiting step. The effects of stirring rate, temperature, composition, and melt geometry were investigated as a means of identifying the controlling step. On the laboratory scale, relatively little work has been done in the area of slag-metal kinetics, primarily because of the problems confronted in attempting to contain liquid slags and metals in laboratory crucibles at steelmaking temperatures. Since graphite is an ideal material for a crucible, several investigations have been carried out on the reduction of various oxides from a slag by carbon in graphite-saturated iron and on the transfer of sulfur between a slag and graphite-saturated iron. Most of this work has been performed in induction furnaces. Studies where the container was not graphite are extremely limited. A single kinetic study of manganese transfer between molten iron and basic slags was carried out by Sano, Shiomi, and Matsushita.' These investigators prepared calcium oxide and titanium oxide crucibles to contain the two-phase system. Only a few experiments were carried out and the results had to be treated qualitatively. Despite the paucity of kinetic data, a large quantity of information is available in the literature concerning the thermodynamics2-12 and physical properties'3-21 of the slags containing manganese oxide and the dilute liquid iron alloys containing manganese and silicon which were involved in this research program. EXPERIMENTAL METHOD A vertical-tube resistance-heated furnace was used in this investigation to study the slag-metal reaction Although most previous slag-metal studies were carried out in induction furnaces, a resistance furnace has several advantages including better control of temperature and stirring rate. Hence, a resistance furnace was selected for this study, and its design is shown schematically in Fig. 1. Slip-cast, fine-grained, low-porosity, lime-stabilized cubic zirconia crucibles were used for the kinetic experiments. The crucibles were 4 1/2 in. high and 2 1/8 in. OD with a 1/16-in. wall. The crucibles were only slightly

Jan 1, 1969

NAME AND OBJECT. SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York ; its corporate name is American Institute of Mining Engineers; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II. MEMBERS. SEC. 1. The membership of the Institute shall comprise four classes, namely 1. Members ; 2. Honorary Members ; 3. Associates ; 4. Junior Members. All members shall be equally entitled to the privileges of membership, except¬ing that Honorary Members, Junior Members, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. The following classes of persons shall be eligible for membership in the Institute, namely : as Members, all professional mining . engineers, geologists, metallurgists, or chemists, and all persons actively engaged in mining and metallurgical engineering, geology, or chemistry ; as Associates, all persons desirous of being connected with the Institute who in the opinion of the Board of Directors are suitable.

Jan 1, 1923

APPLICATIONS for loan contracts for the exploration, development and mining of strategic and critical metals and minerals are now being accepted by the Department of the Interior. The RFC is authorized and directed by Executive Order 10161 to make such loans but the Secretary of the Interior must pass on the necessity for the loan. Applications should be addressed to James Boyd, acting deputy administrator, Defense Minerals Administration, Department of the Interior, Washington, D.C. rather than to the Field Offices of the Bureau of Mines as was first planned. Application forms are not yet available but it has been learned that data accompanying the application should include the known quantity and grade of reserves, the anticipated rate of production, the equipment, supplies, and man power required for the additional production, etc.

Jan 12, 1950

By S. T. Wlodek, John Wulff

Dense, adherent, and ductile coatings of chromium can be applied to Molybdenum by selectively freezing out the chromium solute from a supersaturated copper-or tin-rich liquid alloy. The successful exploitation of this technique depends on the control of variables common to any freezing process. Under the most favorable combimtion of supersaturation, nucleation, and mass-transfey, coatings as thick as 0.004 in. can be obtained. In exploratory experiments it was found that a coating of chromium may be applied to molybdenum by immersing the molybdenum body in a supercooled copper-chromium or tin-chromium melt and selectively freezing out the contained chromium onto the molybdenum body. Supercooling of the liquid metal plating bath can be achieved by cooling, or the maintenance of thermal or concentration gradients in the melt. The technique is similar to conventional dip-plating procedures where the sample is immersed in a molten bath of the pure plating medium, except that in these studies, the plating medium consisted of a dilute solution of chromium in liquid tin or copper. The success of this method requires that the base material to be plated be isomorphous with the coating and insoluble in the plating bath. In addition, the plating bath, while having an appreciable solubility for the coating component, must have negligible solid solubility in the solid plate. Such relationships exist in the molybdenum-chromium, chromium-tin, and chromium-copper systems. Liquid tin and copper are satisfactory as the plating solvent, because although chromium is appreciably soluble in both of these liquid metals, solid inter-solubility is almost negligible, and no compound formation occurs. The same relationships exist between molybdenum and copper or tin except that the solubility of molybdenum in liquid tin or copper is insignificant. It is this combination of solubility relationships, as well as the completely isomorphous nature of the molybdenum-chromium system, which allows the formation of a chromium coating on molybdenum by the selective freezing mechanism. Since the main deterrent to the widespread use of molybdenum for high-temperature structural applications is its poor oxidation resistance, the formation of a dense and ductile chromium coating on molybdenum may well be of commercial significance. In addition, the basic principle of coating formation by selective freezing should be applicable to other metallic or even nonmetallic systems. The precipitation of the solute from a liquid metallic solution, for the formation of a protective coating, has not been previously considered in the literature. Frequently, however, a similar phenomenon has been described in the corrosion of metallic heat exchangers by liquid metals1 wherein temperature gradients in the liquid metal heat-transfer medium result in the formation of layers or deposits of metallic residue2 in the cooler portions of the system. Impregnating techniques using liquid baths have been tried as a plating process. Semchyshen and Barr, for instance, have successfully diffused chromium into molybdenum by immersing the molybdenum specimen in a liquid tin-chromium or copper-chromium alloy. This simple holding technique fails to produce a layer of pure chromium and requires prolonged immersion to allow for the diffusion-activated enrichment of the molybdenum. During the course of this investigation, most of the phase relations published for the copper-chromium4 and molybdenum-chromium4 systems, were found reliable. It was necessary, however, to investigate the solubilities of chromium and molybdenum in liquid tin as well as the solubility of molybdenum in liquid copper. These determinations were made by a simpie weight loss technique on materials of the same purity as used in the plating studies. The results of these solubility studies are given in Tables I and I1 and indicate that although the solubility of molybdenum in liquid

Jan 1, 1961

By T. F. Witherbee

AS the forms of blown-out furnaces are of much interest to ironmasters and metallurgists, the manner of taking the accompanying sections of the Cedar Point stack is here given. The diagrams show the original and also the final shape of the furnace after a two years and twelve days' blast,, during which the following solid materials passed through it, viz.: Coal, 41,000 tons; ore, 57,000 tons; limestone, 30,000; total, 125,000 gross tons. Product, 411/4 tons per day Bessemer pig iron. The apparatus used in taking the sections was a modification of that proposed by Mr. Frank Firmstone,* and consisted of a sliding rule, to follow around the circumference of the stack, which rule was connected by a string to a segment of a circle of 24 inches radius. The segment was carried by an arm which connected it to a huh as a centre, 2 inches in diameter. A second string was wound around the hub, and communicated motion to a pencil-carrier, the pencil of which marked out on paper the exact outline, and reduced it to a scale of & inch to the foot. The whole machine was made in about three hours, with the facilities of a carpenter's shop, and gave in operation every irregularity of the lining. The sections were taken at salient points, by lowering a hanging staging on which the apparatus was placed. Tracings from the paper of the machine were made, and, as in this case several copies were required, the tracings were glued on to thin sheets of basswood, and patterns carefully sawed out with a bracket saw.

Jan 1, 1879

Jan 1, 1889

By O. D. Gonzalez, R. A. Oriani

A thermo-osmosis technique has been used to measure the heat of transport, Q* , of hydrogen and of deuterium dissolved in a iron and in nickel, and of hydrogen in Feo.6Nio.4 in the tempevature range 400° to 600°C. For all these systems, Q* is negative and has a large temperature coefficient; an isotope effect can be established for the solutes only in nickel. The magnitude of Q* is considerably larger than the activation energy, E , for migration in the case of these isotopes in a iron, so that all variants of the Wirtz model must be rejected. The phenomenological definition of Q* is developed to show that Q* is related to the mechanisms by which the activation energy is dissipated back into the lattice, and that Q*/E is a function of the ratios of the mean free paths of electrons and of phonons to the distance of jump of the diffusing atom. A correlation is shown to exist between the sign of Q* in thermal diffusion and that of the effective charge in electro migration, and may be understood as due to the large ratio of the mean free path of electrons to that of phonons. THE study of nonisothermal diffusion in the solid state is of interest because certain aspects of the mechanism of diffusion are made manifest which remain concealed though still present in the isothermal case. The thermodynamics of irreversible processes characterizes nonisothermal diffusion, known as thermal diffusion or as the Ludwig-Soret effect, by a quantity, Q*, called the heat of transport, which essentially measures the sign and the magnitude of the steady-state concentration gradient produced by the imposed temperature gradient. The problem then is to understand the quantity Q* at the atomistic level. There does not exist a theory for the atomistic interpretation of the heat of transport. There are, however, two classes of simple models which seem to afford some physical insight into Q*. Wirtz's model1, z and its subsequent generalizations partition the activation energy, E, for the migration of the atom spatially about the region of the migrating atom, so that Q* is the difference between the portion of the activation energy centered about the original site of the jumping atom and that portion about the arrival site. Clearly, the magnitude of Q* cannot on this model be larger than the activation energy for migration. The model of Oriani3 also considers the spatial distribution of E not only before but also after the atomic jump, and Q* is related to the variation of the spatial distribution of E that is produced by the jump. The simplest kind of system with which to compare the consequences of these ideas is the interstitial solid solution, since one may easily choose a temperature at which only the interstitial component moves, the solvent lattice serving as a completely satisfactory frame of reference. Thus, one avoids complications arising when both species in a binary system move. In addition, one avoids the necessity of knowing the energy for the formation of a vacancy, something which is needed for the analysis of thermal-diffusion data on metals which diffuse by the vacancy-exchange mechanism. However, the number of well-measured interstitial systems is extremely small, and, in particular, there are almost no data in the published literature for the temperature dependence of the heat of transport. If one works with solutes which are gases in the pure state at ordinary temperatures, one may use the technique of thermo-osmosis4 which permits thermal diffusion to be measured over a small temperature difference so that the temperature dependence of Q* can be more easily determined. The choice of dissolved hydrogen in iron and nickel was based on these considerations as well as on the desire to look for an isotope effect associated with localized

Jan 1, 1965

By C. A. Queener, W. L. Mitchell

In recent years bismuth telluride has received considerable attention, primarily due to its value as a thermoelectric material. Since there seems to be little dependence of thermoelectric effect upon crystal orientation1 many of those who have previously worked with this material have been unconcerned with knowing its crystallographic angles to any degree of accuracy. However, when one studies deformation modes, lattice stresses, or the aniso-tropy of mechanical properties of a material, knowledge of the interplanar angles and their relationships as depicted in a stereographic projection becomes essential. Lange2 originally published crystallographic data which described the structure of bismuth telluride as rhombohedral with the space group A more recent work by Francombe3 presented data which corroborated and refined the original findings of Lange. In addition, Francombe established that there is no coexistence of rhombohedral and hexagonal lattices in bismuth telluride as was suggested by Vasenin and Konovalov,4 and that the structure can be treated as a pseu do hexagonal structure with an axial ratio, c/a, of 6.95 for convenience of presentation and study. The interplanar angles and standard projections for several unalloyed hexagonal metals have been previously published,5-9 but the present work appears to be unique in that it presents data for a rhombohedral compound in pseudohexagonal form. As a pseudohexagonal structure, this material has an extremely large axial ratio as compared to the usual range of approximately 1.5 to 1.9 for the hexagonal metals. Since the interplanar angles are a function only of c/a, the angular relations between various planes for Bi,Te3 will be grossly different

Jan 1, 1965

By J. J. Becker

BEAN1 has discussed the magnetic behavior of mixtures of small ferromagnetic particles on the order of 20 to l000A in diam. As he points out, there are three size categories with characteristic properties: 1) Particles large enough to contain many ferromagnetic domains magnetize initially by the motion of domain walls. The initial susceptibility of such particles, if domain-wall motion is assumed to be perfectly easy, depends only on their shape. It is equal to the reciprocal of the demagnetizing factor (and is thus 3/4 tt for a sphere) and is independent of temperature. 2) Smaller particles find it energetically undesirable to contain domain boundaries. They are always spontaneously saturated, and reverse their magnetization only by rotation of their entire magnetic moment. As assemblage of such particles has a remanence which is a large fraction of the saturation of the assemblage; its coercive force is on the order of 2K/1,, where K indicates magnetic aniso-tropy from any source, and I, is the saturation magnetization of the substance of which the particles are made. 3) Particles which are still smaller continue to be single-domain, but the direction of their magnetization fluctuates thermally, as first pointed out by Neel.' They have no remanence and no coercive force and possess the temperature-dependent magnetization curve of a paramagnetic substance with a very large moment. Bean calls this superpara-magnetism. All of these kinds of behavior are observable in alloys consisting of a precipitate of ferromagnetic phase in a nonferromagnetic matrix. Fig. 1 shows a typical aging curve for the room temperature coercive force of a sample of 98 pct Cu-2 pct Co alloy

Jan 1, 1958