Search Documents

By M. L. Samuels

In a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000' C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallo-graphic charaeteristics. The data, which related specifically to tempering temperatures of 550°, 650" and 710" C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemical composition. 2. The temperature of maximum softening spread over a range from about 650" C, to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at sub-eutectoid temperatures. 4. The mode of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hi. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Deterrnirlation of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000" and 850" C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

By B. S. Norris, Charles R. Austin

IN a recent paper the authors1 discussed the reactions to tempering of hypereutectoid steels quenched from 1000° C., as revealed by studies on changes in hardness, electrical resistivity, coercive force and metallographic characteristics. The data, which related specifically to tempering temperatures of 550°, 650° and 710° C., for varying periods up to 125 hr., permitted the following important conclusions: 1. The rate of softening of the steels at the temperatures examined differed markedly although the steels were of "similar" general chemical composition. 2. The temperature of maximum softening spread over a range from about 650° C. to the eutectoid inversion. 3. The divergence in behavior was ascribed, at least in part, to a profound difference in tendency to graphitization on annealing at subeutectoid temperatures. 4. The node of spheroidization of the cementite, as revealed by metallographic studies, also varied considerably in the different steels. The purpose of the present investigation is to pursue further the study of the difference in behavior of the steels on tempering over a wider range of temperature. To this end the following features have received particular attention: 1. Comparison of temperatures of maximum softening of the various steels when the quenched samples were tempered for 5 hr. and for 75 hr. followed by furnace cooling and by quenching in water. 2. Determination of the effect of quenching temperature, prior to tempering, on the rate of softening. Quenching temperatures of 1000° and 850° C. were used in the investigations. 3. Examination of the microstructures obtained with the various heat-treatments employed.

Jan 1, 1938

By E. H. Dix

All commercial aluminum contains small percentages of copper, iron, and silicon as unavoidable impurities. The purest metal obtainable commercially, special grade high purity ingot, contains a maximum of 0.50 per cent. impurities of which the usual minimum amount of copper is 0.01 per cent.; silicon, 0.12 per cent.; and iron, 0.20 per cent. This grade is too costly for most purposes. The two standard grades, Nos. 1 and 2, containing a minimum of 99.0 and 98.0 per cent. aluminum, respectively, are more generally used. Other grades of secondary aluminum often contain as high as 3 or 4 per cent. of impurities, which include 1 per cent., or more, of zinc. Specifications for high-grade aluminum-casting alloys generally allow a maximum of 1.7 per cent. for total impurities. The S. A. E. Specification No. 33, which is intended to cover alloys made from secondary aluminum ingot, gives the iron maximum as 1.5 per cent. and the maximum for silicon (including manganese and tin) as 0.75 per cent. The effect of even relatively small amounts of impurities on the physical properties of ingot aluminum is shown by the following cornparison of two lots of aluminum, which may be taken as representative of special grade and grade No. 2 ingot, respectively. AnalysEs Special Grade, Gbade No. 2, Per Cent. PeR CBnt. Copper................................. 0.01 0.32 Silicon................................. 0.12 0.32 Iron................................... 0.42 0.82 Aluminum.............................. 99.45 98.54

Jan 1, 1923

By E. H. Dix

All commercial aluminum contains small percentages of copper, iron, and silicon as unavoidable impurities. The purest metal obtainable commercially, special grade high purity ingot, contains a maximum of 0.50 per cent. impurities of which the usual minimum amount of copper is 0.01 per cent.; silicon, 0.12 per cent.; and iron, 0.20 per cent. This grade is too costly for most purposes. The two standard grades, Nos. 1 and 2, containing a minimum of 99.0 and 98.0 per cent. aluminum, respectively, are more generally used. Other grades of secondary aluminum often contain as high as 3 or 4 per cent. of impurities, which include 1 per cent., or more, of zinc. Specifications for high-grade aluminum-casting alloys generally allow a maximum of 1.7 per cent. for total impurities. The S. A. E. Specification No. 33, which is intended to cover alloys made from secondary aluminum ingot, gives the iron maximum as 1.5 per cent. and the maximum for silicon (including manganese and tin) as 0.75 per cent. The effect of even relatively small amounts of impurities on the physical properties of ingot aluminum is shown by the following cornparison of two lots of aluminum, which may be taken as representative of special grade and grade No. 2 ingot, respectively. AnalysEs Special Grade, Gbade No. 2, Per Cent. PeR CBnt. Copper................................. 0.01 0.32 Silicon................................. 0.12 0.32 Iron................................... 0.42 0.82 Aluminum.............................. 99.45 98.54

Jan 1, 1923

By Robert M. Lewis

Can wet-ground mica be produced from mica schist ores, and if so, would its properties be comparable with products now on the market? This was the problem which prompted the development of a flowsheet for the beneficiation of mica schist. The fine-ground mica industry relies on weathered pegmatites and alaskite ores as sources of raw material. The mica concentrates obtained from these ores are relatively clean and require moderate beneficiation to meet color and bulk-density specifications. Mica obtained from mica schist is iron-stained and decrepitated and requires additional beneficiation to produce a wet-ground mica product. Despite these adversities, there are several advantages to be gained by mining and processing mica schist ores. The mica content of these ores is considerably higher than that of the pegmatites and alaskite ores now being mined, often containing in excess of 40% mica. This higher-grade mica feed should promote a lower mining and milling cost. The mica schist ores with their higher mica content would mean less tailings to handle; however, there would have to be a means for disposing of acid and sulfate wastes. A flowsheet was developed whereby mica could be recovered from mica schist ores and beneficiated in a way that would result in a high-quality end product.' The essential phase of the process involves using reducing reagents to increase the magnetic susceptibility of iron contaminants which then can be removed with a magnetic separator. General Treatment Procedure The mica is floated by either of two methods, an amine float in an acid circuit' or the U.S. Bureau of Mines (USBM) amine-fatty acid float in an alkaline circuit' The flotation mica is ground in a pebble mill to liberate contaminated particles and expose iron-stained surfaces. The concentrate is then conditioned with a reducing reagent and passed through a Frantz Ferrofilter for the removal of magnetic material. The nonmagnetic product is acid-leached to further reduce the iron contamination. The leached material is then ground to product size and checked for specifications. Discussion of Flowsheet and Its Development Flotation: The mica is concentrated by flotation using either of two methods: an amine float in an acid circuit, or the USBM amine-fatty acid float in an alkaline circuit.' The writer does not wish to elaborate on the relative merits of the two flotation procedures; however, after investigating ores from various localities, it was felt that the amine float in an acid circuit was more consistent when using a standard procedure. Iron Reduction and Magnetic Separation: This phase of the flowsheet may be considered the key to the process. It was developed when it became apparent that hot acid leaching had just about reached its maximum effective¬ness for color improvement. S. C. Sun and William Hirsh in "Hydrochloric Acid Leaching of Iron From Pennsylvania Aluminous Clays,"` reported iron extraction for -20-mesh minerals of 82.20% for hematite and only 33.46% for magnetite. The test procedure employs a 19% hydrochloric acid solution, 104°C temperature, and 10% solids. It was felt that magnetic removal of some of the iron contaminants before leaching therefore would be advantageous. Since the iron minerals present as contaminants vary in magnetic susceptibility, it was decided to experiment with reducing reagents as a means of influencing their magnetic properties. Zinc hydrosulfite or sodium hydrosulfite were the reagents used throughout the tests. The procedure developed consists of conditioning the mica concentrate in a closed container at approximately 5% solids with a reducing reagent. Approximately 10.0 lb of zinc hydrosulfite per ton of mica concentrate is used. The ferric iron is reduced to the ferrous state (magnetic) and oxidation is retarded by isolation from the atmosphere in a closed container. After the desired conditioning time has elapsed, the material is passed through a Frantz Ferrofilter where the magnetic particles are retained and discarded as

Jan 1, 1972

By D. O. Noel, E. B. Gebert, J. D. Shaw

IT. is, of course, expected that manufacture of the various metal powders should involve numerous methods adapted to the specific characteristics of the metals themselves. Several methods for powdering a particular metal may be available, but the physical characteristics of the powder as produced by the several methods may be quite different. In the final analysis, the application of the metal powder dictates the physical properties that the metal powder must possess, and this, to a very large extent, will determine which of several possible methods of. manufacture is adopted. Sometimes powder of the same metal is produced by more than one method, each powder having specific characteristics .that make it particularly suitable for its application. For purposes of classification, the various methods of powdering metals can be grouped as follows: 1. Machining. 2. Milling (by ball mills, stamps, attrition mills, etc.). 3. Shotting (pouring molten metal into water, air, etc.). 4. Granulation (by stirring molten metal while solidifying). 5. Atomizing (disintegrating by steam, compressed air, etc.). 6. Condensation of metal vapor. 7. Reduction of oxide powders. 8. Chemical precipitation. 9. Electrolytic deposition. 10. Sintering (for producing alloy powders). 11. Formation of an alloy followed by dissolving or otherwise removing one of the alloying constituents. MACHINING Turnings, cuttings, filings, etc., are, of course, produced as by-products in machine work of various kinds, and find certain applications as metal powders. For example, iron powder so produced is used extensively as a reducing or precipitating agent and as a constituent in certain hard-finish cements.

Jan 1, 1938

By V. S. Rood, J. A. Norden

The general system of workings at the Utah-Apex is similar to that found in many of the western metalliferous mines. There is a vertical three-compartment shaft extcnding to the surface, from which the various levels have been driven to the orebodies. The 1000-ft. (305-m.) level, about 3/4 mile long, was driven as a haulage and drain adit. Geology The formation is a flat north-dipping series of alternating limestone and quartzite beds. Extensive north-south faulting and fissuring have taken place, resulting in the formation of large replacement orebodies in the crushed zones in the limestone. The orebodies are irregular in shape and size, but follow closely the trend of the mineralizing fissures. The ore consists of galena, pyrite, sphalerite and small values in silver and gold. Large masses of non-commercial pyrite are frequently found in or adjacent to the orebodies, and more or less pyrite is found for some distance in the walls of the orebodies. Lenticular bodies of a black pyritic shale also occur in the zones where extensive faulting has taken place. Mining Methods and Condition of Workings Geological conditions, mentioned before, have made the ground extremely heavy. In mining above the 1000-ft. level, square-set and filling methods were used, but not altogether successfully. The crushing of timbers extended even into the filled portions of the stopes. The filling material itself, consisting of limestone, shale, and pyrite, possessed swelling qualities which added to the difficulty of maintaining

Jan 1, 1920

By Marcel R. Daly

In a preceding paper1 the writer has pointed out some apparent relationship between the distribution, on the surface of the globe,, of the known hydrocarbon deposits and the disposition of the principal zones of deformation of the earth's body (geosynclines). He wishes to present some further remarks on this subject. Petroleum deposits, or their derivatives or descendants, are found through the whole range of sedimentary strata, from the pre-Cambrian to the Quaternary. For instance, the prc-Beltian (Shuswap) series of the Canadian Cordillera are interbedded with limestones which are sometimes rich in carbonaceous matter (Sicamous limcstone); and the Beltian system of the same region contains layers of argillitcs and dolomitic limestones which are equally high in carbon content.2 This carbon may be interpreted as the last remnant of hydrocarbons previously contained in the rocks. On the other hand, the actual formation of hydrocarbons under conditions that would eventually permit their deposition in modern sediments is conceded by some geologists.3 Between these two extreme limits, bitumens are found indifferently in all sedimentaries. Thcy constitute a continuous series, some kind of a large family, whose individual members may be entitled to a community of origin and probably represent the different stages of evolution of the primitive, parent matter. The kinship between petroleum and such substances as asphalt, ozocerite, manjak, grahamite, albertite, etc., is well known; and E. H. Cunning-gam-Craig has recently shown how intimately shale fields and oil fields are connectcd.4 For this reason, no distinction is made in the present

Jan 1, 1918

"No true conception of the Park City mining district can be obtained without first giving consideration to the part it has played as a consistent producer of mineral wealth. Its position in this regard is almost unique in the annals of a lead silver camp. For over fifty years it has been a continuous producer of lead and silver and for twenty years it has added to the world's supply of zinc. Few camps with its productive history are so little known to the mining fraternity for the reason that its life has never been punctuated by periods of ""boom"" which serve to attract general attention, neither has it been the field of operation for promoters who temporarily focus attention upon their scene of action. Its history is one of legitimate mining operations. These were at first carried on by a number of smaller companies. A period of consolidation followed and at the present time the entire production of the camp is in the hands of two major companies and one smaller company. These are flanked by a number of prospecting properties, which are at this time actively engaged in the search for ores and later events will doubtless put some of them in the producing class.A technical discussion of the ore occurrence and mining operations in the camp will be the subject of a paper to be read before this meeting of the Institute. The mission of this article is to supply a ""Baedeker"" where Baedeker is lacking.The town of Park City is a typical, up-to-date, western mining camp which owes its existence as a town of 4,500 inhabitants solely to the mining industry. The camp is located 7,000 feet above sea level, thirty-two miles east of Salt Lake City. It is situated on the Victory Highway seven miles from its junction with the Lincoln Highway and has the benefit of excellent automobile communication with the metropolis of the state. Both the Denver and Rio Grande and the Union Pacific Railroads give daily train service to the camp and effectively solve the transportation problems of the mining companies."

Jan 1, 1925

By Leon Keller, William R. Van Slyke, James Stukel

Two 4-ft wide DSM screens were installed during 1957 in one unit of the two-unit heavy media cy- clone section of the Holman-Cliffs concentrator at Taconite, Minn., following successful laboratory test work on a 1-ft screen. The two screens materially reduced the amount of media sent to the magnetic separator cleaning circuit. Wear life was good and fine size capacity was high. Briefly, the Holman-Cliffs heavy media cyclone plant uses -65 mesh magnetite as media and 10-in. diam., 30º Ni-Hard cyclones as separatory vessels. Feed to the plant averages 130 long tons per hr of -1/8 in. +65 mesh material. The conventional heavy media circuit uses drum or spiral type separatory units and treats +l/8 or 3/16-in. material. The medium is generally -65 mesh ferrosilicon. Ore and media are readily separated by screening at about 6 mesh. At this size, capacity is high and wear and maintenance are not excessive. The heavy media cyclone plant requires an efficient separation between +65 mesh ore and -65 mesh media. To reduce costs, however, the separation was made at a coarser size with the result that the media was un- duly contaminated and it was necessary to clean large tonnages of media and ore in magnetic separators. Due to the high capital cost of these units, their number was kept to a minimum and, consequently, they were overloaded. As a result, the separation between magnetic media and nonmagnetics was not sharp and the magnetite losses were high.

Jan 10, 1958

By D. L. Katz

A PHASE diagram showing boundary curve and quantity of liquid in the two-phase region was determined for a mixture of natural gas and natural gasoline in the region of its critical conditions. The tempera-tures and pressures of phase measurements were in the range of 85° to 212° F. and 1300 to 2600 lb, per sq. in., respectively, with the critical conditions at 169.5° F. and 2615 lb. per sq. in. abs, Color phenomena were observed in the region of the boundary curve from 102° to 192° F. Approximate densities of the single-phase and two-phase regions and analysis of the system are included. Boundary curves between the single-phase and the two-phase regions have been determined for several binary mixtures containing hydro-carbons. 2,3,4,6,7,10,11,12,14 These investigators did not report the relative amounts of liquid and vapor within the two-phase region. The equilib-rium values obtained from the dew-point and bubble-point data can be used to compute the lines showing percentage of liquid on the pressure-temperature phase diagrams but the positions of the lines near the critical temperature and pressure are uncertain. Relative amounts of vapor and liquid were obtained for a gasoline and a naphtha' within the two-phase area but not in, the region of the critical temperature and pressure. The bubble-point and dew-point lines, as well as the percentage liquid lines within the two-phase region, were determined by visual observations in glass apparatus.

Jan 1, 1939

By R. G. Garlick, M. Garfinkle

It was observed for several bcc metal crystals that the Knoop hardness anisotropy was dependent essentially on the direction of the lung axis of the indentor alone and not on the plane of indentation. The generality of this observation was tested for an fcc md an hcp metal and an ionic crystal. For cubic crystals, this observation was valid; for the hcp structure, however, the planes of indentation did have an effect on the hardness anisotropy, although this was not nearly as significant as the direction of indentation. Because the direction of indentation is the only significant crystal-lographic parameter necessary to describe the hardness anisotropy, it is possible to represent the anisotropy of single crystals on the standard stereographic triangle. THE commonly observed1, 2 periodic variation of indentation hardness with crystallographic direction on the high-symmetry planes of various single crystals has been inadequately related to the physical or mechanical properties of the crystals examined. In fact, the hardness anisotropy curves for the various planes of a particular metal crystal, as is illustrated in Fig. 1, are uncorrelated and appear in the literature3, 4 as unrelated observations. Attempts to correlate hardness anisotropy curves with specific physical properties can be generally divided into either mechanistic or nonmechanistic approaches. A nonmechanistic approach would be to devise a mathematical expression that could describe the various hardness anisotropy curves. Such a relation could then be compared with the known anisotropy of various physical properties to determine which contribute to the observed hardness anisotropy. No such mathematical expression has been found in the literature.

Jan 1, 1969

By R. R. Kimpel, L. G. Austin

An equation is derived describing fragment size for single fracture of brittle solids. It contains the equations of earlier workers as special or approximate cases and, in addition, is capable of describing coarse distributions in which a few large particles are produced on fracture. The equation can be fitted well to single fracture experiments where over-breakage is avoided. In 1956 Broadbent and callcottl described a method of analyzing the unit operation of grinding, applicable to homogeneous breakage of brittle materials. In essence, the grinding process was split into two parts: 1) the fractional amount of a given size which is selected for grinding per unit time, 2) the size-weight distribution of the fragments produced by breakage of this certain size (primary breakage distribution function). The theory was formulated using matrix algebra. They attempted an experimental verification of the theory using an assumed primary breakage distribution but the results were not very satisfactory. Austin and Gardner2 showed that this assumed distribution was widely different from experimental values and that it led to the poor agreement of predicted size-weight distributions with experiment found by Broadbent and Callcott. In addition, Austin and Gardner2,3,4 reformulated the original approach in terms of differential equations of grinding and demonstrated that the approach led to a very satisfactory description of the grinding process, providing that the descriptive parameters were measured experimentally. Recent work5 has substantiated these findings and the distribution functions of several materials ground under different conditions in different mills have been determined experimentally. The fraction underweight versus size used by

Jan 1, 1965

By J. D. Shaw, E. B. Gebert, D. O. Noel

It is, of course, expected that manufacture of the various metal powders should involve numerous methods adapted to the specific characteristics of the metals themselves. Several methods for powdering a particular metal may be available, but the physical characteristics of the powder as produced by the several methods may be quite different. In the final analysis, the application of the metal powder dictates the physical properties that the metal powder must possess, and this, to a very large extent, will determine which of several possible methods of manufacture is adopted. Sometimes powder of the same metal is produced by more than one method, each powder having specific characteristics that make it particularly suitable for its application. For purposes of classification, the various methods of powdering metals can be grouped as follows: 1. Machining. 2. Milling (by ball mills, stamps, attrition mills, etc.). 3. Shotting (pouring molten metal into water, air, etc.). 4. Granulation (by stirring molten metal while solidifying). 5. Atomizing (disintegrating by steam, compressed air, etc.). 6. Condensation of metal vapor. 7. Reduction of oxide powders. 8. Chemical precipitation. 9. Electrolytic deposition. 10. Sintering (for producing alloy powders). 11. Formation of an alloy followed by dissolving or otherwise removing one of the alloying constituents. Machining Turnings, cuttings, filings, etc., are, of course, produced as by-products in machine work of various kinds, and find certain applications as metal powders. For example, iron powder so produced is used extensively as a reducing or precipitating agent and as a constituent in certain hard-finish cements.

Jan 1, 1938

By D. O. Noel, E. B. Gebert, J. D. Shaw

It is, of course, expected that manufacture of the various metal powders should involve numerous methods adapted to the specific characteristics of the metals themselves. Several methods for powdering a particular metal may be available, but the physical characteristics of the powder as produced by the several methods may be quite different. In the final analysis, the application of the metal powder dictates the physical properties that the metal powder must possess, and this, to a very large extent, will determine which of several possible methods of manufacture is adopted. Sometimes powder of the same metal is produced by more than one method, each powder having specific characteristics that make it particularly suitable for its application. For purposes of classification, the various methods of powdering metals can be grouped as follows: 1. Machining. 2. Milling (by ball mills, stamps, attrition mills, etc.). 3. Shotting (pouring molten metal into water, air, etc.). 4. Granulation (by stirring molten metal while solidifying). 5. Atomizing (disintegrating by steam, compressed air, etc.). 6. Condensation of metal vapor. 7. Reduction of oxide powders. 8. Chemical precipitation. 9. Electrolytic deposition. 10. Sintering (for producing alloy powders). 11. Formation of an alloy followed by dissolving or otherwise removing one of the alloying constituents. Machining Turnings, cuttings, filings, etc., are, of course, produced as by-products in machine work of various kinds, and find certain applications as metal powders. For example, iron powder so produced is used extensively as a reducing or precipitating agent and as a constituent in certain hard-finish cements.

Jan 1, 1938

By Thomas H. Leggett

In speaking of the mining and economic conditions prevailing at the present time on the Rand, it is not my intention to go into the details of the mining practice, since this has been already well described both in the Transactions' and elsewhere,2 but rather to take a more comprehensive view of the industry and its surroundings as a whole, marking its general development and the lines of its future progress. In a paper entitled Deep-Level Shafts on the Witwaters-rand, with Remarks on a Method of Working the Greatest Number of Deep-Level Mines with the Fewest Possible Shafts,' presented to this Institute in August, 1900, I drew attention to the great cost of sinking the very deep vertical shafts that were then being seriously proposed as necessary for the development of the deeper areas, pointing out the strong advisability of working this ground by means of inclines to be sunk from the existing shafts of from 3,000 to 4,000 ft. in vertical depth. In this paper it is stated (p. 975): '" In short, practice upon the Rand now tends towards fewer vertical shafts and more underground inclines, especially for the very deep mining about to be undertaken." In consequence, the 6,000-ft. vertical shafts, at one time so much discuesed, have never been started, and they do not now seem likely ever to be. The necessity of placing all deep shafts further apart in order to make them control and exhaust larger areas was also dwelt upon. This economy wae vitally necessary for both

Jan 1, 1909

By L. D. Godshall

A great deal has been written of late regarding the loss of silver in assaying; very discordant results have been published by different writers, and much uncertainty exists concerning even approximate losses in a careful determination of silver, as represented by a fire-assay. In the present paper it has been the aim of the writer to determine as accurately as possible the losses sustained by silver, under certain specified conditions, during the process of cupellation. Such losses are well known to be due to absorption by the cupel and volatilization. The conditions, however, which govern these losses are not believed by the writer to be so well understood. The most important of these are : 1. The effect of variable quantities of silver used. 2. The temperature of cupellation. 3. The character and quantity of impurities in the lead button. 4. The weight of the lead button. 5. The nature of the cupel. The following experiments were made for the purpose of demonstrating, as nearly as possible, the total loss of silver in cupellation under the most favorable conditions to be obtained in commercial assaying. Chemically pure silver and pure lead were taken. The latter was obtained from test-lead, first melted into a bar, from which pieces of the desired weight were cut and accurately weighed. The experiments recorded in this paper were planned by the writer, but executed throughout by Mr. J. N. Walker, whose ability as an accurate, careful and painstaking assayer is too well known and recognized throughout the West to require any further endorsement from me.

Jan 1, 1897

By Alan R. Grant

The Cascade Range of Washington can be considered metallogenetically to be primarily a copper province. Structural and chemical data compiled from examination of numerous copper occurrences in the Cascades indicate a marked parallel of physical conditions for sulfide deposition. In probable order of significance, the environmental criteria are as follows: 1) adjacent or subjacent, postregional metamorphism high-level intrusive activity, most commonly in the time range from 15 million years to 30 million years; 2) transverse northeast trending structural belts which obliquely cut the northwest regional trend of the range; 3) potassium-silica wall rock alteration; most important of the alteration suite of silicates are orthoclase secondary biotite and quartz; 4) the intersection of northwest trending and northeast trending structures. The varying geologic environments in the Washington Cascades present a complex setting for the sulfide deposits. The North Cascades are comprised of predominantly pre-Tertiary metamorphic rocks invaded by Tertiary calcalkaline intrustive rocks. The Central Cascades, lying south of the North Cascades, exhibit a younger, higher level geologic environment comprised of predominantly early to middle Tertiary volcanic rocks and subordinate sedimentary rocks which are intruded by Tertiary calc-alkaline igneous rocks. Although the Tertiary Cascade intrusions are dominantly quartz dioritic, copper mineralization is commonly found in rocks of quartz monzonite to granite composition. These acid rocks appear to be the product of late stage magmatic K alteration of the original quartz diorites. Sulfide concentrations are considered to be in part dependent on the degree of K-silicate activity and the intensity of transverse structural deformation.

Jan 1, 1973

The Library of the above-named Societies is open from 9 A.M. to 10 P.M. on a11 week-days, except holidays, from Sept. 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by for- warding copies of mining reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 8, 1916

By J. Husson, R. Iffly, M. Gondouin

A systematic variation of well deliverability, as reflected from isochronal back-pressure tests performed at regular intervals, has been observed in some gas condensate wells producing at high rates. The same effects have been obtained using a numerical model of gas and condensate flow which takes into account secondary gasoline deposited in the pore space as a result of pressure reduction, and non - Darcy flow of gas in the vicinity of the wells. Matching calculated values with previous test results has been possible, and future predictions have been obtained. An application of this method to the Hassi Er R'Mel gas-condensate field in Algeria is tentatively shown. INTRODUCTION Flow capacity of gas wells is generally derived from an analysis of back-pressure tests. The empirical equation q = C (?p2)n used by Rawlins and Schellhardtl can be derived rigorously assuming that steady-state radial flow of a dry gas of constant viscosity and compressibility is established during each flow period of the well tests. Furthermore, when Darcy's law applies in the entire flow region, the theory predicts that the exponent n is equal to 1. In low-permeability reservoirs, it was soon discovered that the time required to reach a stabilized flow often exceeded the duration of the flow periods normally available for testing wells. Consequently, transient gas flow had to be considered instead of the steady-state assumption previously used. This led to the isochronal testing procedure established by Cullender2 which has largely replaced conventional back-pressure testing. For dry gas fields, this method yields definite values of C and n equivalent to those of the empirical equation. These values should remain constant for each well as long as the permeability of the formation and the characteristics of the gas (viscosity and compressibility) do not change appreciably. This is the case when reservoir pressure remains -close to the original value and when the formation near the wellbore remains free of plugging. Under those conditions, stabilized flow potential curves of gas wells can be established from a single sequence of isochronal flow and shut-in periods. An analysis of a pressure build-up following a longer production period provides additional data on the transmissivity (k h/ u) of the reservoir, and eventually on the 'drainage radius rd of the well, which can be related to the value of C so that future performance of the well can be predicted using the concepts developed by A. Houpeurt.3 At high flow rates, Darcy's law no longer applies in the vicinity of the wellbore, and inertial effects in the high velocity gas flow introduce additional pressure drops. As a consequence, exponent n of the backpressure tests becomes smaller than 1, and a slight curvature of the log-log plot of ?p2 vs q can be predicted when going from very low to high rates of flow (Elenbaas and Katz).5 The effects of variations of viscosity and compressibility with pressure on the radial flow of dry gas in an infinite reservoir were taken into account by Jenkins and Aronofsky.7 Numerical solutions of the transient flow of an ideal gas in finite radial reservoirs were presented by Bruce, Peaceman, Rachford and Rice.8 In the case of gas condensate wells, however, the presence of gasoline in the pore space as soon as reservoir pressure is reduced below the dewpoint pressure further complicates the interpretation of flow tests so that the prediction of stabilized well performance becomes very difficult. Field observation shows that both C and n derived from isochronal tests vary in time, even when reservoir pressure has not changed appreciably. Such a variation cannot be attributed to any change of the gas characteristics, and must result from the effect of a gasoline saturation on the gas flow.