Search Documents

By Kendall E. Born

Production of crude oil in Tennessee during 1940 was slightly more than 15,000 bbl., a decrease from 1939 of about 36,000 bbl. This sharp decline has been caused largely by curtailed activities in the shallow pools in Clay County, where approximately 3000 bbl. was marketed off the lease during the year as against more than 37,000 bbl. in 1939. The flashy production found in 1938 in the Celina area has been short-lived and the area is essentially abandoned. Failure to find steady production has been the major factor retarding developments in the northeastern Highland Rim area. The Mississippi lime production in Scott and Morgan Counties continued to show a steady decline. The Tennessee production by counties is shown in Table I. Table i.—Oil Production in Tennessee it1 1940 Production. Bbl. Number of County Wells Pumped 1939 1940 Scott............ 4 4,332 3.596 Morgan.......... I: 6,479 5,751 Fentress.......... 3 I,2XX 1,5xz Pickett........... 1 1.2XX Clay............. 8 37.200 3,XXX Developments There were 32 wells spudded in during 1940, four of which were drilling or only temporarily suspended on Dec. 31, 1940. Twenty-eight wells were completed during the year, four of which were commercial producers. The total footage drilled was 3I,214 ft. The more important wildcats are listed in Table 2; the distribution of 1940 oil and gas tests according to physiographic divisions is given in Table 3. Cumberland Platenu.—Thcre was one completion in the coal area of the state, a test that attempted to extend the Mississippi lime production in the Coon Hollow pool to the southeast in Morgan County. This test encountered only slight shows of oil in the producing horizons of the near-by Coon Hollow and Boone Camp pools. Some surface work was carried on by private interests during the year in Scott and Morgan Counties and two wells were spudded in early in 1941 The revival of interest in the Kentucky portion of the plateau will probably result in increased activity in this part of Tennessee during 1941. Several sizable blocks of acreage, some by major oil companies, are held in Scott, Morgan, and Cumberland Counties. Middle Tennessee.—The northeastern Highland Rim continued to be the most active area in the state with 20 completions, although this figure is about one third of the number drilled in 1939. Four oil wells, none with initial productions of more than I00 bbl., were completed in Clay, Fentress, and Pickett Counties. The producing horizons discovered in Pickett and Fentress Counties were in the "Sunny-brookJ' pays of Trenton age. The Clay County producer was an old test drilled deeper in which oil was found at 671 ft. in the upper part of the Stones River group of limestones, a common pay in this area. All four wells were drilled in or close to old shallow production. Deeper testing into the Knox dolomite group in this area was not particularly encouraging, although one well in Fentress County encountered some saturation at 1860 to 1869 ft. in the upper

Jan 1, 1941

By Pol Duwez, Paul Pietrokowsky

Titanium and vanadium form a complete series of solid solutions at temperatures above 885°C. Below 885°C, vanadium is slightly soluble in a titanium (about 1.5 pct V at 650°C) and a two-phase a plus ß region extends to 18.5 pct V at 650°C. The alloys up to 15.0 pct V transform into a supersaturated a solid solution upon rapid cooling from the ß phase. Above 15 pct V the ß phase may be retained. The temperature at which the ß to a' martensite-type transformation takes place decreases steadily from 850°C for 0.5 pct V to 325°C for 12.7 pct V. IN the transition series of the periodic table, the six elements that have a body-centered cubic structure at all temperatures, namely chromium, vanadium, molybdenum, columbium, tungsten, and tantalum, fulfill the conditions required for the existence of complete series of solid solutions with the high temperature (ß) form of titanium. Up to the present time, complete solubility at temperatures above the a to ß transformation of titanium has been observed in the systems Ti-MO,1,2 Ti-Cb,2 Ti-W,³ and Ti-Ta.³ The two remaining elements, vanadium and chromium, have atomic diameters which are not as near that of titanium as the atomic diameters of the four other elements. Both are smaller than titanium and the difference, expressed in percentage of the titanium atomic diameter, is 12.3 pct for chromium and 8.2 pct for vanadium. On this basis, the least favorable conditions for solid-solution formation are therefore encountered in the Ti-Cr system. The early work on the Ti-Cr system4 revealed that up to about 1100°C the solubility of chromium in ß titanium is limited, and an intermetallic phase exists near the stoichiometric composition TiCr2. It was found later' that a continuous series of solid solutions extends across the diagram at higher temperatures, and TiCr2 forms by solid state reaction. It became apparent therefore that complete solubility would also be present in the Ti-V system. The present investigation confirms this possibility. The iodide-refined titanium used in this investigation was purchased from the New Jersey Zinc Co., New York. According to the manufacturer, a typical analysis of this product is 0.0065 pct Mn, 0.0022 pct Fe, 0.0015 pct Cu, and 0.0042 pct Pb. The Vickers hardness number (10 kg load) of the crystalline bar varies between 55 and 80. The vanadium metal was purchased from the Westinghouse Electric Corp., Lamp Div., Bloomfield, N. J. The purity of this metal is probably above 99 pct V. The oxygen content must have been quite low, since a bar about 1/4 in. square could be cold rolled into a ribbon 0.020 in. thick. To prepare the various alloys on the titanium-rich side of the diagram, the titanium rod was machined into cups 1 cm in diam and about 1.5 cm high. Pieces of vanadium, of the proper weight, were cut from the square bars and placed within the cups prior to melting. On the vanadium-rich end of the diagram, single pieces of the metals, in the proper weight pro-

Jan 1, 1953

By J. T. Dewan

An experimental setup is described whereby the responses of Neutron logging instruments have been determined opposite formations of different porosities and under various borehole conditions. The results of these tests are presented in several charts which show how the Neutron log is affected by the following factors: hole diameter, casing, cement, salinity and weight of drilling mud, and position of logging tool with respect to the wall of the hole. The responses in the case of empty holes are also shown. A chart is furthermore presented which shows the shapes of the Neutron log, as a function of logging speed and time constant, at the boundaries between two formations with different porosities. These were derived mathematically using as a basis laboratory determination of the shape of the curve under static conditions, i.e. at very low logging speed. Corrections for the readings made opposite thin beds are given by these computations. The correction is found negligible under usual logging conditions for beds thicker than about 4 ft. INTRODUCTION The Neutron log is used in borehole surveys both for the delineation of porous formations and for the quantitative estimation of their porosities.1,2,3,4,5 It is common practice to calibrate the response of the Neutron log in terms of porosity values for each given geological unit by means of empirical comparisons between the deflections of the neutron curve and the porosity values given by the core analysis in a sufficient number of wells. Usually, the plots of the porosity values vs Neutron log deflections show a definite trend. It is therefore possible to trace an average line across the plotted points. This average line constitutes a calibration curve which can be used to evaluate the porosities from the Neutron logs in the other wells drilled in the same region. Futhermore, when the porosity values are plotted on a logarithmic scale and the Neutron log deflections on a linear scale, the calibration curve is practically a straight line. Accordingly the calibration curves are often determined by simply tracing a straight line between two points corresponding to two widely different porosities. Different choices are made for these two points, depending on local conditions. For example, one point will be defined by plotting the deflection of the Neutron curve opposite a formation known to be very tight, for which an average porosity value of 1 or 2 per cent is assumed. The other point may correspond to shale sections, to which a porosity of around 40 per cent is ascribed. The information provided by the eletrical logs — in particular the Laterolog, Limestone log or Micro-Latero-log — is also very often a help in the calibration of the Neutron logs. Empirical approaches such as these make possible the derivation of fairly reliable porosity values from the Neutron logs in many cases, at least in open holes and in essentially clean formations. There are, however, several causes of uncertainty which may sometimes entail appreciable errors. On the one hand, the Neutron log readings are influenced by the borehole conditions: hole diameter, presence or absence of casing and cement, presence or absence of drilling mud, characteristics of the mud, and position of the logging instrument with respect to the wall of the hole. The amplitudes of the curves opposite thin beds are furthermore atfected by the bed thickness,

Jan 1, 1957

By C. S. Smith, L. H. Beck

KNOWLEDGE of the Cu-Zn constitution diagram was critically examined in 1944 by G. V. Ray-nor,1 who suggested the diagram reproduced in Fig. 1 as the best evaluation of available data. No pertinent work on the constitution has been published since that time, although a number of authors have discussed transformation kinetics and theory. Despite the large amount of work that has been done on the constitution of these industrially important and scientifically interesting alloys, minor uncertainties still exist. For example, it is still not possible to say definitely whether a two-phase region exists between the ordered and disordered forms of the 8 phase. A careful re-examination of the phase boundaries in this part of the diagram was therefore undertaken. Two methods were selected for the new investigation—quantitative metallography for the higher temperatures and precision lattice parameter measurement for lower temperatures. Because of the relatively narrow two-phase regions flanking the ß phase in these alloys, quantitative metallography is particularly suited for their examination, since the relative amounts of the two phases are very sensitive to their compositions. The method, however, is useless below about 350°C because of the inadequate resolution of the two constituents. Below 400°, however, the X-ray diffraction method is applicable, although it is of somewhat lower sensitivity in this system. The changes of composition that occur during quenching from above about 500°C entirely vitiate X-ray measurements at room temperature though they do not affect metallographic area measurements. The two methods overlap and supplement each other admirably. Both methods depend on the attainment of equilibrium composition of the two phases in a more or less intimate mixture and thus avoid the difficult problems of nucleation and long range diffusion involved in the conventional metallographic bracketing method. The alloys were melted from a master alloy made from re-electrolyzed cathode copper and Horsehead 99.99 pct Zn. Melting was done under a cover of either borax or charcoal and the alloys cast into a 7/8 in. sq graphite mold for the a-ß alloys or a 3/8 in. diam cylindrical graphite mold for the ß-? alloys. The a-ß alloys were rolled at 750°C to 5/8 in. sq; annealed for 24 hr at 800°C and quenched; then rolled and swaged at 200°C to 3/8 in. diam rods, annealed 24 hr at 200°C, quenched and cold rolled 2 pct reduction. This treatment was intended to obtain a small grain size and to produce many nuclei of the minor phase for growth on subsequent heat treatment. The unworkable ß-? alloys were given preliminary treatment by sealing in Vycor tubes in vacuum and annealing for 4 hr at 800°C followed by cooling in air. Samples of homogenized alloys were checked spectrographically for impurities, but the principal components were determined on samples subsequent to heat treatment. The impurities analyzed averaged approximately as follows: Ag, 0.0002 pct; Fe, 0.004; Si, 0.0008; Cd, 0.005; Mg, 0.0002; and Pb, 0.002. For metallography, samples of appropriate composition were cut into rods 5/8 in. long, sealed in pyrex tubes in vacuum and annealed for eight weeks at temperatures of 470°C and below, two weeks at 480°, 500°, and 600°C, and 4 hr at 700°C, followed by quenching in cold water. Temperatures were accurate to ±2°C. The cylinders were then machined to 8.7 mm diam and a slice weighing 1.5 g cut with a thin saw transversely from the center of each. This

Jan 1, 1953

By J. W. Whalen

The design, operation and evaluation of an instrumental method for the determination of fluid saturation in porous materials during multiphase flow studies is described. The presence of a magnetic tracer comprising approximately 20 per cent by weight of the aqueous phase is necessary in the utilization of this method. The results of two-phase relative permeability studies on two samples of porous media are presented. The realizable accuracy of the magnetic susceptibility apparatus in fluid saturation determination is estimated to be 2 saturation per cent. The response characteristics of the instrument, together with its simplicity of operation and maintenance are sufficient to recommend its use in routine laboratory studies. INTRODUCTION The problem of fluid saturation determination in laboratory multiphase flow studies characterizing oil recovery processes is one which has been given exhaustive study. Briefly the requirements which are considered essential for a method sewing this purpose are: (1) that the measurement be made external to the porous rock sample under study with no interruption of the fluid flow pattern, (2) the saturation indication must be independent of fluid distribution in the volume scanned by the measuring device, (3) the sensing element should have a small field of definition enabling several independent measurements to be made along the length of a core sample, and (4) the properties of the fluid phases should not be too greatly influenced by required tracer substances. Several methods of saturation determination have found acceptance as meeting most of the above requirements. These include resistivity,1 X-Ray absorption,2,3,4 radiotracers,5,6,7 and neutron8 diffraction The merits of these techniques have been discussed elsewhere in detail and will not be considered here. It may, however. be pointed out that the elaborate instrumentation required by the methods mentioned above, with the exception of the resistivity method (which is undesirable from other standpoints) encourages the development of methods of saturation determination which, while meeting the requirements listed, are simple to operate and maintain. It is the purpose of this paper to describe the instrumentation and evaluation of a technique for the determination of fluid saturation which combines relative simplicity with an accuracy and applicability comparable with methods now in practice. DESCRIPTION OF THE METHOD If the magnetic susceptibility of one of the fluid phases contained within a porous material is sufficiently greater than that of the remaining phases, the fluid content of the material with respect to that phase may be determined by an induction measurement. This may be accomplished by measuring the induced voltage in the secondary of a transformer which contains the porous sample and its interstitial fluids as a portion of the magnetic flux path. Since the fluids used in multiphase flow studies involving petroleum reservoir samples possess uniformly low magnetic susceptibilities, the use of a magnetic tracer in one of the fluid phases is required. In view of the relatively high paramagnetic susceptibility of salts of the transition elements, together with their high water solubility. these compounds become logical choices as tracer materials. Cobaltous chloride, having a specific magnetic susceptibility of 17.5 x 106 cgs electromagnetic units, was used as the tracer material throughout this work, in a concentration of approximately 20 per cent by weight in the aqueous phase. MAGNETIC SUSCEPTIBILITY APPARATUS Basically, the magnetic susceptibility apparatus consists of a transformer serving as the detecting head, a

Jan 1, 1955

By V. Koump, T. F. Perzak, R. G. Olsson

The vate of dissolutioz of carbon in molten Fe-C alloys urns studied by votating- cylindrical g-vaphite sairlples in a stationary crucible containing the melt. The rate of dissolltion was determdined from the change in the bnth co)npositiorz. Alccss-tvansfev coeffi'cients, calcilated with the assurlption that the inte)yacial liquid ulas saturated with carbon, were found to be in agreement with an existing Correlation fov mass transfer jroni votating cylinders. It is corzcllrded tlat, itz the wnge of- Reynolds' numbers itzvestigated (790 to 18,000), the vate of dissolutio of carborz in Fe-C alloys is controlled by tile rate of carbon difirsion from the interface. The dissolution of carbon in molten Fe-C alloys has been the subject of a number of investigations. Most of these investigations have been inconclusive because of poorly defined experimental variables. Two of the more sophisticated studies are summarized below. Dahlke and Knacke' studied the phenomenon by, in part, immersing graphite rods into 0.5 pct carbon-steel for different lengths of time. Since the experiments were conducted in air or in CO atmospheres, the melt was strongly agitated by gas evolution. It was concluded that the change in bath composition as a function of immersion time was in agreement with the assumption that the dissolution process was transport-controlled. The hydrodynamic conditions in these experiments, however, were not well-defined and gave no indication of the nature of the dissolution process at higher fluid velocities. In a recent study Shurygin and ruk investigated the dissolution of carbon in molten Fe-C, Fe-Si, Fe-P, and Fe-Ni alloys. Small graphite disks were rotated in a crucible containing molten alloys under such conditions that only the lower face of the disk was exposed to the melt. The results of this investigation indicate that, over the range of velocities (100 to 1000 rpm) and bulk liquid concentrations (0.7 to 4.5 wt pct C) considered, the dissolution of carbon in the iron alloys is limited by the diffusion of carbon from the interface to the bulk liquid (a transport mechanism). For the particular geometry used by these authors, exact analytical solutions of hydrodynamic and diffusion problems are aailable. Hence the experimental results obtained by Shurygin and Kryuk permit the evaluation of diffusion coefficients of carbon in the four systems investigated. In the present investigation a series of experiments were conducted in which the rate of dissolution of carbon in Fe-C alloys was measured under conditions which permitted wide variation of the fluid velocity and the carbon concentration of the bulk liquid. Graphite cylinders were rotated at different speeds in a stationary concentric crucible containing various molten Fe-C alloys. THEORETICAL DEVELOPMENT In general, the resistance to mass transfer from a solid interface to a turbulent liquid is assumed to reside in a laminar boundary layer adjacent to the interface. If it is also assumed that the diffusion coefficient is independent of concentration, the steady-state rate of dissolution for the case of arbitrary liquid and solid densities can be obtained from the integration of the equations of continuity. The derivation is similar to that used by Lommel and chalmers4 for the case of pl = ps. The solution, expressed in terms where N = rate of diffusion of the solute from the interface. Exact analytical solutions of the hydrodynamic equation for the boundary layer thickness are available for only a limited number of geometries. Consequently, a mass-transfer coefficient, k, is usually

Jan 1, 1967

By G. Y. Chin, A. R. Von Neida

The relationship between crystalline texture and magnetic anisotropy in a Co-10 pct Fe alloy has been investigated by means of X-ray pole .figures, hysteresis-loop tracings, and magnetic-torque measurements. The cold-rolled texture of a sample after 95 pct thickness reduction is of the "brass-type", that is, (110)[112/. At 500°C the cold-rolled material recrystallizes fo a (311)[112] orientation, plus a minor (210) [001] component. This texture persists up to 1400°C, at which point it is replaced by a secondary recrystallization texture, (111)[112]. Magnetic-torque measurements show that the easy axis of magnetization lies along the transverse direction in the cold-rolled material and changes to the rolling direction after primary recrystallization. This change is also reflected in the hysteresis characteristic; whereas the B-H loop along the rolling direction is nonsqunre with a low value of residual induction (750 vs 19,000 gauss at saturation) for the cold-rolled material, the annealed sample exhibits a very square loop with a large value of residual induction (16,000 gauss). Theoretical torque curves calculated from the texture data on the basis of magnetocystalline anisotropy energy compare favorably with the observed torque curves. Values of the crystal anisotropy constant, K1, obbained from these comparisons are in good quantitative agreement with single-crystal data. Furthermore, both the torque amplitude of the poly crystalline material and the magnitude of K1 obtained with a single crystal show an identical temperature dependence over the range from —195° 10 +220°C. It is thus conclzided that the magnetocrystalline anisotrpopy erlergy is chiefly I-esponsible. for the nzagnetic allisotropy of textured Co-10 pct Fe alloy. THE results of a study on the relationship between crystalline texture and magnetic anisotropy of an alloy containing 90 pct Co and 10 pct Fe by weight are reported in this paper. The alloy has an fcc structure: a saturation magnetization of about 19,000 gauss,2 and a nearly zero value of magnetoatriction.3 puzey4 has reported a large crystalline anisotropy constant of -7.4 X 105 ergs per cu cm, indicating the (111) directions as the easy axes of magnetization. Hence, texture variations resulting from cold work and annealing are expected to introduce a magnetic anisotropy in the polycrystalline material through the alignment of these (111) easy directions. In the present study, magnetic anisotropy of both rolled and annealed strips was determined by magnetic-torque measurements and hysteresis-loop tracings The results were correlated quantitatively with calculations based on texture data obtained by the X-ray pole-figure technique. It is established that the magnetocrystalline anisotropy energy is indeed chiefly responsible for the magnetic anisotropy of textured Co-10 pct Fe alloy. EXPERIMENTAL Material Preparation. The alloy nominally contained 90 pct Co, 9.5 pct Fe, and 0.5 pct Mn by weight, the chief impurities being nickel, carbon, and silicon (less than 0.5 pct total). The cast ingot was rolled to strips 10 mils thick and slit to 1 in. in width. After strand annealing at 900°C in a hydrogen atmosphere, these strips were further cold-rolled to various thicknesses down to 0.25 mil (97.5 pct reduction), with samples collected for study of the development of texture and magnetic anisotropy as a function of thickness reduction. subsequently, samples cold-rolled from 100 mils to 0.25 mil were obtained, thus extending the thickness reduction range to 99.75 pct. In addition, 0.5-mil samples cold-rolled from 10 mils were selected

Jan 1, 1965

By A. Soundraraj, S. Singh, R. C. Deshpande

THE detonation of a high-explosive charge having a metal-lined conical cavity (shaped charge) results in a fast-moving jet and a slow-moving slug.1-4 Clark and Bruckner reported the metallographic studies of a cast-iron slug. The present note describes the metallographic studies of a copper slug and discusses the principle of flow involved. The shaped charge consisted of a 5-cm diam cylinder of cast high explosive (60-40 RDX-TNT mixture) having a 45 deg and 0.16-cm thick copper cone. The copper (99.5 pct purity) had a grain size of 0.06 to 0.08 mm diam and a hardness of 65 to 75 Hv. These were fired into a deep container of water and the slugs were recovered undamaged. The longitudinal and transverse sections of the slug were polished, etched, and examined for mi-crostructural changes. Macroexamination revealed a radial grain flow inwards towards the center and a downward component of flow towards the base of the slug. Fig. 1 shows schematically the micro-structural changes observed on the longitudinal section of the slug. The region D near the apex and also along the outer surface of the slug was characterized by the presence of heavily deformed and twinned grains. Some of the grains were having bent or crossed twins, Fig. 2. The grain size in this region was of the same order as that of the

Jan 1, 1960

By D. L. Harris, A. M. Gaudin

THE following results, presented here in condensed form,1 were obtained in a preliminary study of the adsorption of n-hexane thiol, hexyl mercaptan, on sphalerite, zincite, willemite, and quartz, from aqueous solution and from a gas. Interest in this subject was aroused by a Belgian report2 of effective use of hexyl mercaptan for flotation collection of oxidized zinc minerals. The relatively low boiling point, 149°C, of the mercaptan3 suggested the desirability of extending the usual measurements of partition of collector between aqueous solution and gas and between gas and mineral. It is believed that this paper presents the first measurements of this type on a flotation system. Attempts were made to carry out the measurements at equilibrium, but as the work progressed it became increasingly doubtful that this desirable condition had been achieved. To control composition and extent of the gas phase, the apparatus was a wholly-enclosed thermally-controlled glass system. Because of these constraints and the desirability of dealing with pure minerals, a scale of operations was chosen in which a few grams of deslimed mineral were used in each test. It was also necessary to choose a particularly sensitive method for mercaptan analysis, and in fact a method that would permit the experimenters to follow the approach to equilibrium. For these reasons mercaptan marked by radiosulphur 35 was used. An analysis was made for the radiosulphur by a modification of the method of Gaudin and Carr.4

Jan 9, 1954

By Maurice Cook

A procedure of obtaining specimens of lead, tin, and cadmium with a moderately equiaxed structure and a smooth surface suitable for etching without grinding and polishing is described; the advantages of general oblique illumination (as opposed to vertical illumination) in the photomicrography of pure metals .are stated. Using these methods, a statistical study of the changes brought about in deformed lead, on annealing, has been made. The common mode of structural change was found to be recrystallization. Cases of growth of one original grain into another were rare; but if a totally recrystallized specimen was annealed above 200° C., a few large grains appeared and spread over the whole area, except for a certain number of small grains which remain unabsorbed. The temperature needed to produce structural change in lead was found to be lower, the greater the degree of deformation. With tin, an extension of 28 per cent. caused practically no recrystallization at ordinary temperatures, but recrystallization occurred if the specimen was heated to 100° C. In cadmium at low temperatures, the grain size decreased in marked manner as the deformation increased; but at high annealing temperatures, the grain size was comparatively independent of the degree of deformation. THE structural changes in metals brought about by annealing following a deformation at a low temperature has been the subject of many investigations. No less than eleven metals and alloys have been studied in some detail; namely, aluminum,1 tungsten,2 iron,3 copper,4 gold,5

Jan 11, 1924

By W. T. Turrall, M. J. Cook

A discussion of modern developments in beneficiation of fine sizes of anthracite, this paper includes a description of the plant flowsheet, an analysis of operating results, and a summary of fundamentals of mineral separation relative to plant operation. DURING the past several years Lehigh Naviga-tion Coal Co. has installed equipment at Tamaqua and Lansford collieries for cleaning and sizing No. 4 buckwheat —3/32 + 3/64 in. and for recovering and cleaning flotation coal —20 + 200 mesh at Tamaqua colliery. Papers describing some of these installations have been presented to AIME. At Coaldale colliery, however, methods used to clean fine coal were inadequate and inefficient. Management decided upon a thorough investigation of all existing processes before building a plant to treat the combined three sizes mentioned. Investigation, carried out on company property and at other plants, entailed a study of hydrotators, hydroclassifiers, tables, spirals, flotation machines, methods of screening, and methods of dewatering. On the basis of this investigation a flowsheet was designed which necessarily excluded many processes in use, and the writers wish to emphasize that no criticism is implied by omission of processes or machines. A determining factor in selection of many machines was the policy of standardizing equipment wherever possible. Flowsheet and Operational Data The first principle to be considered in designing of any plant is efficiency of cleaning as related to laws of classification. Beneficiation of coal may be described as separation of two materials having different specific gravities. Although there is an inherent ash content even in the purest coal which slightly affects its specific gravity, it is recognized that many particles are true middlings. The percentage of these particles allowable in the final product depends upon the ultimate ash, or specifications of the consumer. Richards in his study of free settling and hindered settling classification' determined that particles of equal size and different specific gravities had unequal settling velocities. He also determined a definite size relationship for equal settling velocities with free settling and hindered settling conditions. Considering the design of machines used to clean No. 4 and No. 5 buckwheat, it may be assumed that both free settling and hindered settling conditions exist and that ratio of size for practical operations is between the established values. The essential factor is that the more efficiently and closely sized the feed is maintained, the more nearly perfect the resulting separation. Flowsheet design was governed primarily by factors related to the 1200 to 1500 tons per hr feed to the main plant. It should be stressed that because of the many sources of supply from mine and stripping, the physical characteristics of this feed varied considerably. The most significant influence was varying percentage of fines, necessitating that all machines be capable of operating under maximum peak load during periods of surge. Since cleaning practice is a wet process, about 9000 gal per min containing 14 to 15 pct solids, or 350 tons per hr, must be treated. This slurry contained all the fines, or —3/32 in., but also percentages of oversize, up to 1 % in., dependent on spills or breaks in screen jackets, a not uncommon occurrence in preparation plant practice. The flowsheet developed is shown in Fig. 1. Circled numbers represent points of sampling. Table I gives operational data including size, ash by size, composite ash, rate of flow in gallons per minute, percent solids dry weight, and average tons of solids per hour. It should be noted that these results are subject to human error in sampling practice. Detailed information reported is a representative evaluation of plant operation.

Jan 1, 1954

By A. G. Metcalfe

Observations at temperature are used to investigate the phase changes in alloys containing more than 50 pct Co and above 1000°C. The nonsuppressible transformations in cobalt above 1120°C and in the intermetallic compound Co2Cr3 are studied. The liquidus and solidus surfaces are determined. Insufficient data is obtained to complete the constitution diagram. A REVIEW of some of the earlier work on cobalt' and on the binary systems with chromium2-4 and with molybdenum,5 showed that one likely source of differences might be attributed to the presence of phases at high temperatures which could not be retained by quenching. Consequently, the decision was made that only methods of examination at temperature should be used in this work. The correctness of this decision was confirmed during the course of the work by the investigation of the martensitic nature of the transformation in cobalt- and by the decomposition of the high temperature form of the phase Co2Cr3 on quenching.' The use of high temperature methods, including dilatometry and thermal etching led to the postula-tion of the existence of a high temperature form of cobalt with a probable hexagonal close-packed structure, transforming from cubic cobalt over a range of temperature from 1119° to 1145°C.8 One of the important pieces of evidence for this transformation was that it was observed in alloys with chromium and molybdenum which were nonmagnetic at this temperature so that confusion with magnetostriction effects was impossible. These results were not reported in this earlier paper, so that the data given here supply further evidence for the existence of a second allotropic transformation in cobalt. High temperature observations are necessarily much slower in producing results than the examination of quenched specimens at room temperature by conventional means such as X-ray diffraction or microexamination. The investigation has only covered a limited part of the field, as a result, extending from the liquidus down to about 1050°C and from the cobalt corner up to 50 pct alloying elements. The differences between the various reported diagrams for the constitution of the Co-Mo and Co-Cr systems have already been mentioned. The best available diagram in the first system is due to Sykes and Graff' which is shown in Fig. 1. Fig. 2 shows the latest Co-Cr diagram due to Elsea, Westerman, and Manning.' A comparison reveals that these are incompatible because of the disagreement with regard to the number of allotropes of cobalt. Elsea, Westerman and Manning took their liquidus and solidus curves from Wever and Haschimoto.2 The temperature horizontal in the two-phase field beneath the eutectic was placed 35" to 39°C higher than in earlier work2,4 with a new interpretation of the nature of this transformation. This interpretation also required a peritectic horizontal at about 1470°C, which has been confirmed here for an alloy with 53 pct Cr. No investigation had been made of the ternary system until after this work had been terminated, when a section at 1200°C was published." In this work a ternary compound was found by the X-ray diffraction examination of quenched alloys. This compound contained less than 50 pct Co, and was thus outside the field investigated here. However, some reactions were found dilatometrically which could not be fitted on the diagram and are now believed

Jan 1, 1954

By W. Mostowitsch, H. O. Hofman

The mineral gypsum, CaSO4 + 2 H2O, has been used for many years as a sulphurizing and basic flux in several smelting-operations. Thus, in smelting oxide nickel-ore in the blastfurnace, it is commonly added to the charge to furnish the sulphur necessary for collecting the metal in a matte, and a base for slagging the siliceous gangue. In the concentration of lead-copper matte in the reverberatory furnace it has been used for years at Preiberg, Saxony,1 for a similar purpose, and for producing at the same time a copper-matte with less than 0.15 per cent. of Fe. The latest use gypsum has been put to is in the blast-roasting process of Carmichael-Bradford.2 The term " blast-roasting," given by A. S. Dwight3 to the Dwight-Lloyd method of roasting and agglomerating: is a happy generic term which covers the ground better than the " lime-roasting " of Ingalls5 or the " pot-roasting " of Austin: in that it leaves the operation independent of the character of the flux and the form of apparatus, and retains the characteristic feature of this class of processes—namely, that of using forced draft. In the Carmichael-Bradford process the dehydrated material, mixed with galena-concentrate, acts as a diluent and a flux. The process differs in this from the Huntington-Heberlein7 and the Savelsberg8 processes, in both of which limestone is used.

Jan 1, 1909

By A. Perry Thompson

I- GeneRal Distribution, AppeaRance, and Relations ........ 563 11. Data fRom MicRoscopic Examination............... 568 1. Criteria for Distinguishing Primary from Secondary Minerals...... 568 2. The Leonard Vein Filling..................... 574 Quartz............................ 575 Pyrite............................ 575 Enargite............................ 576 Covellite............................ 578 Bornite............................ 581 Chalcocite........................... 583 Chalcopyrite.......................... 586 3. The Fault-Vein Covellite..................... 587 The Speculator Ore........................ 587 The East Gray Rock Ore.....,.............. 589 4. Other Occurrences of Covellite.................. 591 111. Conclusions........................... 592 1. The Replacement of Minerals..................592 2. The Character of Mineralizing Solutions .............. 594 I. General Distribution, Appearance, and Relations Mining in Butte has seldom encountered covellite in commercial quantities. The notable occurrences, extending vertically and laterally perhaps several hundred feet, presented scattered, bladed lenses of this mineral in a matrix of quartz, pyrite, enargite, bornite, and chalcocite. But under the microscope covellite is seen to be widespread in the Butte ores, though in such small quantity that megascopic examination will not discover it. In early mining operations covellite was found in the Gray Rock vein, a member of the Blue vein system. As described by Sales,' it persisted as an occasional ore mineral, associated with quartz, pyrite, tetrahedrite, bornite, chalcocite, and minor amounts of sphalerite, from the 700-ft. to the 1,200-ft. level of the East Gray Rock and Diamond mines. Crushed quartz-monzonite and later quartz completed the vein filling between

Jan 1, 1916

By Leo Tarasov

MAGNETIC torque studies of ferromagnetic single crystals have been carried out in a number of laboratories during the last decade1,2 and some work has been reported on polycrystalline material showing preferred orientation. Goss3 used the method extensively in developing electrical sheet with desirable magnetic properties, but he used it as a control rather than as a means of studying the texture. Bozorth4 made a quantitative correlation of a torque curve he obtained from some cold-rolled iron with the texture as determined from X-rays, but did not extend his studies beyond the one specimen. Other studies, which have been reported from time to time 1.5 have also been incomplete in the sense that no effort was made to study a whole series of samples, differing only in degree of cold reduction, or in the annealing temperature, in order to ascertain the effect of such treatments on the texture as revealed by torque measurements. It is the purpose of this investigation to make such a study, mainly in order to see how useful the method can be made when used under favorable circumstances and to find what kind of a correlation can be expected between magnetic and X-ray studies of texture. Before proceeding further, it is desirable to say a little about single crystals, so as to make clear the concepts involved in magnetic torque measurements.

Jan 1, 1939

By Tedsen L. F., Dorn J. E., A. E. Flanigan

since aluminum-alloy sheet may be used occasionally at moderately elevated ternperatures, the effects of temperature on the mechanical properties are of interest. Recently the short-time tensile properties of several high-strength materials have been studied at temperatures up to 3750°F.l This paper deals with stress-rupture and creep properties at the same temperatures. The work was done at the University of California as a portion of the project NRC-548. It was financed by the War Production Board and was supervised by the Office of Production Research and Development. This paper has been released for publication by the latter agency. The following materials were studied, all in the form of 0.040-in. sheet: Alclad 24s-T Alclad 24s-T8I Alclad 24s-T86 Alclad 75s-T R3oI-T (clad) Specimens were loaded in tension in the cross-grain direction. Testing temperatures included 94°F., 2II°F., 300°F., and 375°F. Stress levels were selected to cause rupture in times ranging from several minutes to 1000 hr. In each test the following data were obtained: (I) fracture time, (2) elongation at fracture, (3) the complete strain-versus-time curve (creep curve), (4) creep rate (defined in a later section). Materials Materials for specimens were obtained from the manufacturers' commercial

Jan 1, 1947

By Tedsen L. F., Dorn J. E., A. E. Flanigan

since aluminum-alloy sheet may be used occasionally at moderately elevated ternperatures, the effects of temperature on the mechanical properties are of interest. Recently the short-time tensile properties of several high-strength materials have been studied at temperatures up to 3750°F.l This paper deals with stress-rupture and creep properties at the same temperatures. The work was done at the University of California as a portion of the project NRC-548. It was financed by the War Production Board and was supervised by the Office of Production Research and Development. This paper has been released for publication by the latter agency. The following materials were studied, all in the form of 0.040-in. sheet: Alclad 24s-T Alclad 24s-T8I Alclad 24s-T86 Alclad 75s-T R3oI-T (clad) Specimens were loaded in tension in the cross-grain direction. Testing temperatures included 94°F., 2II°F., 300°F., and 375°F. Stress levels were selected to cause rupture in times ranging from several minutes to 1000 hr. In each test the following data were obtained: (I) fracture time, (2) elongation at fracture, (3) the complete strain-versus-time curve (creep curve), (4) creep rate (defined in a later section). Materials Materials for specimens were obtained from the manufacturers' commercial

Jan 1, 1947

By Donald Ofte, L. J. Wittenberg

The absolute viscosity coefficients and activation energies for viscous flow of bismuth, lead, and zinc are reported. The viscosities were measured in an oscillating cup viscosimeter from nearly 1000°C to within 1 deg of the melting point of zinc; 2 deg of the melting point of lead; and in the supercooled condition of bismuth, 9 deg below the melting point. Two methods of relating the change in the viscosity coeflicient with temperature were compared. From the plot of the logarithm of viscosity (77) as a function of reciprocal absolute temperature (1/T), the equations of the lines which fit the data are: AS a part of the Reactor Fuels and Materials Research program at Mound Laboratory, precise measurements of the physical properties of liquid metals are of interest because the desirability for a low vapor pressure liquid coolant in high-temperature nuclear power plants has focused attention on the properties of the liquid metals.' Also, a clearer understanding of the liquid metal state can be achieved when better measurements are available. For these reasons, the viscosity values of certain liquid metals have been determined. The viscosities of the liquid metals, bismuth, lead, and zinc are measured in an oscillating cup viscosi-meter. In this apparatus the liquid is sealed in a right-circular cylindrical cup which is attached to a torsion fiber so that the system forms a torsion pendulum. The damping effect of the molten metal upon the normal oscillations of the torsion pendulum is a function of the viscosity of the liquid. This method is advantageous because of the small amount of sample required (8 to 10 cc), the ease of remote operation of the apparatus in a vacuum system, and the containment of the liquid metal in a hermetically sealed, nonreactive, tantalum crucible. With the liquid metal sealed in the crucible, loss of liquid by vaporization and chemical reactions with atmospheric gases are prevented. Additionally, an absolute viscosity determination is obtained which avoids the sources of possible error in a relative measurement. The difficulties in a relative method include the repetitious cup calibrations, and the uncertainty inherent in the practice of calibration of the apparatus at room temperature and extrapolation to the high temperatures necessary for the investigation of most liquid metals. The oscillating cup viscosimeter was first described by Meyer in 1891.2 The first complete mathematical treatment offering an absolute measurement of viscosity with this type of apparatus was proposed by Andrade and chiong3 in 1936 for an oscillating sphere filled with a liquid. This solution was modified to include a right circular cylinder by Hopkins and Toye4 in 1950, and R. Roscoe5 in 1958. Roscoe's treatment for the calculation of the viscosity of a liquid at a particular temperature from the logarithmic decrement and period of oscillation of the torsion pendulum was used in this investigation. A detailed description of the method of calculating the viscosity from these measurements has been reported earlier.' This calculation has been programmed for the IBM 704 and IBM 1620 computers for expedition of the otherwise laborious calculations. APPARATUS The cutaway view of the apparatus in Fig. 1 shows the suspension system within the high vacuum enclosure. The low residual gas pressure. maintained between 1 x 10-4 and 5 X 10-6 mm Hg during a determination, avoided both air drag on the pendulum and

Jan 1, 1963

By Haydn H. Murray, Sam H. Patterson

The term clay is somewhat ambiguous unless specifically defined, because it is used in three ways: (1) as a diverse group of fine-grained minerals, (2) as a rock term, and (3) as a particle-size term. Actually, most persons using the term clay realize that it has several meanings, and in most instances they define it. As a rock term, clay is difficult to define because of the wide variety of materials that compose it; therefore, the definition must be general. Clay is a natural earthy, fine-grained material composed largely of a group of crystalline minerals known as the clay minerals. These minerals are hydrous silicates composed mainly of silica, alumina, and water. Several of these minerals also contain appreciable quantities of iron, alkalies, and alkaline earths. Many definitions state that a clay is plastic when wet. Most clay materials do have this property, but some clays are not plastic; for example, halloysite and flint clay. As a particle-size term, clay is used for the category that includes the smallest particles. The maximum-size particles in the clay-size grade are defined differently on various grade scales. Soil investigators and mineralogists generally use 2 micrometers as the maximum size, whereas the widely used scale by Wentworth (1922) defines clay as material finer than approximately 4 micrometers. Some authorities find it convenient to use the term clay for any fine-grained, natural, earthy, argillaceous material (Grim, 1968). When used this way, the term includes clay, shale, or argillite, and some argillaceous soils. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, the term is generally understood by those who use it. Clay is an abundant natural raw material, and it has an amazing variety of uses and properties which will be discussed in this chapter. Clays rank among the leading industrial minerals in both tonnages produced and total value. Their importance is indicated in Table 1, which lists the 1978, 1979, and 1980 production and values according to the US Bureau of Mines (Ampian, 1980). Statistical data summarizing world production of kaolin, bentonite, and fuller's earth are compiled by the US Bureau of Mines (Ampian and Polk, 1981). The total world bentonite production in 1980 was 6,625,204 st of which the United States produced 4,184,619 st. The total fuller's earth produced in the world in 1980 was 1,952,600 st of which 1,534,000 st was produced in the United States. The total world kaolin production in 1980 was estimated at 22,971,000 st. Approximately 13 million tons of this total was produced in two countries, the United States and the United Kingdom. World production data on ball clay, fire clay, and miscellaneous clays are not available. As industrial minerals, clays are a complex group that consists of several mineral commodities, each having somewhat different mineralogy, geologic occurrence, technology, and uses. In this chapter these commodities are organized as follows: (1) bentonite and fuller's earth; (2) kaolin, ball clay, halloysite, and refractory clays; and (3) miscellaneous clay and shale. Bentonite and fuller's earth are grouped together because they are closely interrelated. Though bentonite is a term based on mineral composition and fuller's earth is a term based on use, the two are virtually inseparable, because much, but by no means all, clay sold as

Jan 1, 1983

By L. F. Tedsen, A. E. Flanigan, J. E. Dorn

SINCE aluminum-alloy sheet may be used occasionally at moderately elevated temperatures, the effects of temperature en the mechanical properties are of interest. Recently the short-time tensile properties of several high-strength materials have been studied at temperatures up to 375°F. This paper deals with stress-rupture and [ ] creep properties at the same temperatures. The work was done at the University of California as a portion of the project NRC-548. It was financed by the War Production Board and was supervised by the Office of Production Research and Development. This paper has been released for publication by the latter agency. The following materials were studied, all in the form of 0.040-in. sheet: Alclad 24S-T Alclad 24S-T8I Alclad 24S-T86 Alclad 75S-T R301-T (clad) [ ] Specimens were loaded in tension in the cross-grain direction. Testing temperatures included 94°F., 211°F., 300°F., and 375°F. Stress levels were selected to cause rupture in times ranging from several minutes to boo hr. In each test the following data were obtained: (I) fracture time, (2) elongation at fracture, (3) the complete strain-versus-time curve (creep curve), (4) creep rate (defined in a later section). MATERIALS Materials for specimens were obtained from the manufacturers' commercial

Jan 1, 1946