Search Documents

By J. S. Koehler, F. Seitz

THE dislocation theory of plastic flow originated in 1928, when Prandtl1 suggested that the internal damping of metals of plastic origin might arise from the motion of a crystalline imperfection. Following this, Dehlinger2 employed a similar imperfection in a theory of recrystallization. The first detailed theoretical discussions were those of E. Orowan3 and G. I. Taylor4 in 1934. The resulting theory was gen- eralized by J. M. Burgers5 in 1939. Mott and Nabarro, in England, and Seitz and Read,6 in the United States, started an extensive examination of the atomic theory of dislocations in the period between 1939 and 1941. However, this development was arrested by the mar and was not taken up again until after 1945. Since 1946, the field has been the object of very intense activity, particularly in the United States and England. Dislocations are beautiful and intricate imperfections; they are sufficiently complicated to account for the great variety of phenomena encountered in the field of plastic flow. Above all, the dislocation concept enables us to understand how a metal or other plastic solid can deform inelastically under very small stresses at temperatures far below the melting point. Suppose we attempt to shear a perfect crystal plastically. This can be done by sliding one entire atomic plane simultaneously through one atomic distance with' respect to the near-

Jan 1, 1954

By Joseph D. McClung, L. G. Austin

INTRODUCTION Run-of-mine (ROM) coal generally falls into two major groups, that from underground mining (continuous mining machines) and that from strip mining. Continuous miners produce a finer product and strip mining a coarser product that is crushed to produce the desired size. Further size reduction depends on the proposed use or uses for the coal. For example, for pulverized coal power plants as a rough general rule, the coal is ground or pulverized to 80% less than 200 mesh (0.075 mrn) before it is blown into the boiler furnace as a coal-air suspension. For solvent-refined coal processes, the desired size is about <30 mesh ( <0.60 mm) ; in fluidized bed uses, the coal is typically < in. ( < 1.6 mm); for Lurgi pressure gasifiers, the desired size is 1-2 1/2 in. (25-63 mm). Coal preparation plants typically work with a coarse size fraction of 6x1 1/4 in. (15Ox32mm). It seems probable that the next decades will see much wider application of coal cleaning before use and that the stages of crushing and pulverization from ROM coal to end use will be integrated with coal cleaning processes. Since different cleaning processes work better with different ranges of coal size and the degree of cleaning possible is inti-

Jan 1, 1979

By J. H. Clemes

The process of leaching silver ores with sodium hyposulphite is comparatively new, and published accounts of the details and losses of the process are as yet very few. The following account of a careful series of experiments to determine the actual loss in this process may therefore be acceptable to members of the Institute. The ore treated was highly calcareous, and the principal sulphide present was iron pyrites. Following is an analysis by Professor Price, of San Francisco, of the ore treated : Per cent. Silica,..........15.13 Sulphur,.........13.31 Arsenic,.......... 9.82 Iron............ 17.33 Alumina,..........1.35 Zinc,...........4.92 Lead,..........1.78 Carbonate of lime,..33.78 Magnesia,.......... 2.58 100.00 Ten tons were crushed dry with a 30 X 30 screen = 900 holes per square inch. In order to feel our way with this ore, two experimental or "pilot" charges were roasted. Pilot Charge No. 1. Treated 1000 pounds in a four-hearth reverberatory. 8.30 p.m.—Entered fourth hearth, remaining there one and onehalf hours; sulphur began to burn. 10 p.m.—Changed to third hearth; ore became red-hot half an hour after entering; the fireplace was kept almost destitute of fuel. 2.30 A.M.—Changed to second hearth. Charge continued, giving off a large quantity of sulphurous fume; the fireplace was kept dark.

Jan 1, 1884

By Holbrook Botset

EXPERIMENTS performed in this laboratory on the flow of gas-liquid mixtures through unconsolidated sands have been described and discussed in an earlier paper.4 In these earlier experiments a definite relationship was found between the liquid saturation of a sand and its permeability to the liquid or gas phase. Furthermore, the nature of the sand, the permeabilities of the sands over a range between 17 and 260 darcies, appeared to have a negligible effect upon the saturation-permeability relation. Likewise experiments indicated that the viscosity of the liquid, or the substitution of an immiscible liquid for the gas phase, had only a very slight effect on the permeability-saturation relation. This con-clusion has since been definitely confirmed by the experiments of M. C. Leverett3 on the flow of oil and water through unconsolidated sands. The sands used by Leverett were of very low permeability (between 6.8 and 1.04 darcies), while the oil-water viscosity ratio varied between 90 and 0.057. Since the sands that constitute petroleum reservoirs are largely con-solidated, although of widely varying degrees of consolidation, it was desirable to extend the experiments on gas-liquid mixtures to consolidated sand. In the study of consolidated sands additional variables are involved, but for the initial experiments the only new variable to be intro-duced was the cementing material.

Jan 1, 1939

By Lloyd Pollish, Robert N. Breckenridge

SUCCESS in any underground mining operation is determined by accessibility of the orebody, which in turn is dependent upon maintenance of passageways to the mining zones and temporary support of the voids caused by extraction of ore. This is accomplished by one or a combination of the following methods: timbering, back-filling, pillaring, or, more recently, rock bolting. Timbering has usually been the principal means of maintaining these underground openings necessary for mining operations. Timber, however, does not prevent ground movement beyond the scope of localized sloughing, which is indicated by the gradual failing of the timber itself. Besides this, timbering has always been a costly process, and with the decline of available supplies of timber close to the mining areas, mining men have constantly sought other methods of controlling ground. Rock bolting is now replacing timbering at an ever increasing rate. Experience has proved that this form of ground support is just as applicable to blocky igneous rock as to stratified rock. Besides preventing sloughing of the walls and back of underground openings, Fig. 1, rock bolting has a stabilizing effect on the surrounding ground in much the same manner that steel reinforcing rods add to the strength of concrete structures. Further, rock bolting is flexible and may be applied to any shaped excavation, whereas timber sets are in a fixed pattern and the ground must often be changed to conform with this pattern. Rock-bolting installations were made in metal mines of the Northwest as early as 1939. An exhaust air crosscut was driven that year in one of the Butte mines of the Anaconda Copper Mining Co. The crosscut was rock-bolted and gunited at the time it was driven and is still being used to exhaust hot humid air from the 3400 level of the Belmont mine. It is interesting to note that no sloughing or caving has taken place in the 14 years it has been open. Even though these early installations of rock bolts were successful, few men recognized their potentiality until recent years, when the coal mines started their programs of mechanization and the great trend toward roof bolting began. In some areas of the Northwest stopes that previously required heavy timbering and close backfilling are now being mined by the more economical cut-and-fill and shrinkage methods. When used in conjunction with timbering, rock bolting increases the efficiency of the operation by decreasing hanging wall dilution and by making it possible to blast larger rounds. Most of the rock bolts installed to date in mines of the Northwest have been the 1-in. diam slot and wedge type, but there has been a recent trend to- ward using the 3/4-in. diam expansion shell bolt shown in Fig. 2. In addition to these commercially manufactured steel bolts, wooden bolts have been used with considerable success by the Day Mines of Wall&apos;ace, Idaho. Installation of the slot and wedge type requires three distinct operations, with tools for each operation: 1—drilling the hole to proper diameter and depth, 2—setting the bolt, and 3—tightening the nut. Holes are drilled and bolts set with pneumatic rock drills. A number of setting or driving tools have been used successfully, but most follow the same general pattern. Usually the driving tool is designed to accommodate a short length of drill steel on one end and the rock bolt on the other end. In this manner the hammering effect of the rock drill is transmitted through the steel and driving tool to the bolt. When machines not having stop rotation are used, slippage is allowed between the driving tool and bolt or between the drill steel and driving tool. The rock bolt nuts are tightened either with pneumatic impact wrenches or with hand wrenches. Impact wrenches are desirable because they are faster and assure adequate tightness. Expansion shell bolts have the following advantages over slot and wedge rock bolts: 1—No special equipment other than a wrench is needed for their installation. 2—Installation is faster. 3—They are removable. 4—Holes need not be drilled to a specific depth as the expansion shell will anchor anywhere along the length of the hole. These advantages are offset somewhat by the lesser strength of the bolt, since expansion shell bolts are generally made from 3/4-in. diam steel as compared to 1-in. diam steel for the slot and wedge type. One manufacturer, however, is now fabricating expansion shell rock bolts from steel of high tensile strength, which gives this ¾-in. bolt a much greater strength than that of the mild steel bolt. Table I illustrates tests made by the Anaconda Copper Mining Co. to determine the proper hole size to use with various types of bolts and to determine

Jan 1, 1955

By John Crawford

MUCH has been written of late regarding the flotation of coal as a means of reclaiming the valuable portion of the fines encountered in nearly all methods of coal preparation. Whether the process be wet or dry, whether the dust be sent through the entire process or removed prior to the cleaning by some such method as screening or aspiration, one of the final products consists of a considerable proportion of -48-mesh material. The percentage of this -48-mesh material depends upon the mining method, transportation, storage, and method of preparation. The ton-nage of this dust material ranges from 1 to 10 per cent of the total output of the cleaning plants. Four methods of disposal are available for this coal: 1. Disposal with the refuse from the plant. 2. Addition, after being reclaimed from the wash water, or dust collectors, without cleaning to the larger sizes. 3. Separate disposal as a pulverized fuel. 4. Cleaning so that addition to the larger sizes benefits the product as a whole. It is also true that flotation in one form or another is the only known way to effectively clean this material. While some processes do a reason-able cleaning job down to and including +100 mesh, by far the greater-majority stop at or short of the +48-mesh size.

Jan 1, 1935

By E. Maxwell, C. J. Bechtoldt, H. C. Vacher

IN the course of an investigation of the properties of metals at low temperature there was occasion to determine the constitution of four iridium-osmium alloys. There is very little information in the literature1 on the constitution of synthetic Ir-0s alloys. Zvyagintzev&apos; s has made a comprehensive study of different natural Ir-0s alloys and concludes that alloys containing more than 32 pct 0s have the close-packed hexagonal structure of osmium, whereas those containing less than 32 pct 0s have the face-centered cubic structure of iridium. The alloys studied in this work were prepared by the American Platinum Works, Newark, N. J., and were received in the form of fragments approximately 1.5 mm average diameter. The fragments had been obtained by crushing ingots made by fusing charges of iridium and osmium under an arc and air cooling. The ingots were not given a homogenizing heat treatment. Sample fragments Table I. Results of X-Roy Diffraction and Microscopic Examinations Phases Present as Determined by X-ray Diffraction Osmium Alloy Close- Iridium Face- Packed Centered Osmium, Iridium, Hexagonal Cubic Mlcro- WtPot Wt Pct Structure Structure scope 0 99.9 None Present 1 23.6 76.4 None Present 1 38.7 61.3 Present Present 2 59.4 40.6 Present Present 2 79.0 21.0 Present Not detected 2 99.9 0 Present None 1 Note: Chemical analyses of the iridium, osmium, and alloys were furnished by the American Platinum Works. of the iridium and osmium used in making the alloys also were included. Several fragments of each metal and alloy were examined microscopically and by X-ray diffraction. For the X-ray method the fragments were crushed further to pass a 270-mesh screen, then sealed in evacuated fused-silica tubes, heated to 1100°C for 18 hr, and allowed to cool in the furnace. Powder X-ray diffraction patterns were obtained from the annealed fragments by means of a Norelco camera having a diameter of 114 mm, and unfiltered cobaIt radiation. For the microscopic examination several fragments in the as-received condition were mounted in Melmac, (American Cyanamid Co.) and ground using the conventional series of abrasive papers. The polishing was done with 0-2 diamond abrasive on a Microcloth (Buehler Ltd.) lap, wet with xylene. After polishing, the surface was etched electrolytically in a 10 pct solution of chromic acid or in a 10 pct solution of potassium cyanide. Both reagents attacked the osmium-rich constituent, whereas the iridium constituent was attacked slightly by the chromic acid reagent and not noticeably by the potassium cyanide reagent. The results of the X-ray diffraction and microscopic examinations are summarized in Table I. Fig. 1 shows the microstructure of a 21 pct Ir-79 pct 0s alloy. The results indicate an appreciable solid-solu-bility range of osmium in iridium as was reported by Zvyagintzev.&apos; The solid-solubility range of iridium in osmium is more restricted, apparently less than 21 pct Ir. This implies a large range of composition in which two phases can coexist that was not reported by Zvyagintzev.

Jan 1, 1955

By D. A. J. Swinkels

The problem of determining oxygen levels in liquid steel to aid in deoxidation control has received general attention for a number of years. Work in this direction started at the B.H.P. Central Research Laboratories early in 1967 with an evaluation of sampling techniques followed by vacuum fusion analysis to determine the oxygen content of the samples (1). It was found that these techniques had a number of drawbacks if they were to be used for deoxidation control. The method of analysis was rather too slow to allow effective control and measured total oxygen level rather than dissolved oxygen. Furthermore, the results were found to be very variable due to slag entrainment in the samples. Attention therefore turned to the galvanic cell method using a solid oxygen ion conductive electrolyte such as cubic stabilised zirconia. The ionic conductivity properties of electrolytes such as (ZrO2) 85 (CaO).15 had been studied by a number of investigators and had already been applied to the measurement of oxygen activity in gases, in lower melting metals such as copper, lead, tin, silver, alkali metals and indeed the first studies in steel had been made (2,3). Since then the results of a number of studies in the development of an expendable oxygen probe for steel have been reported (4-9).

Jan 1, 1972

By J. W. Downey, S. T. Zegler

A study has been made of the occurrence of Phases having the Cr30-type structure in ternary alloys having the general composition where B cept for iron and copper all the B components are known to form binary compounds having the type structure. The occurrence of the struc-ture type in the ternary alloys was investigated using optical and X-ray metallography. The results indicate that iron can replace virtually none of the cobalt in at 900°C, but substitutes for nickel in up to the approximate composition tually insoluble in V3Ni and 2) and exhibit complete solubility. At 100 nickel can be substituted for cobalt in VSCo up to the composition solubility; and 3) in the system , two solid solutions having the type structure occur. At the same temperature, 1000°C, V3Si exhibits limited solubility for V3Co but is completely mis-cible with V3Ga. Lattice parameters have been determined for all the binary and ternary phases. The solid solutions are discussed in terms of the atomic size and electronic factors which are thought to influence the occurrence of Cr30-type phases. The binary compounds V3Co and V3Ni were found to form peritectoidally from o phases and a vanadium, the former compound at a temperature between 1000" and 1050°C, the latter between 800°and 900°C. The substitutions of nickel and rhodium for cobalt in V3Co were determined not to raise the superconducting transition of VSCo to a temperature as high as 2°K. The occurrence and stability of binary intermediate phases having the Cr30- or A15-type structure (space group o;, Pm3n) have been discussed in several recent papers . Vanadium forms the struc -ture at or near V3B stoichiometry with all the mem -bers of the cobalt and nickel groups in the periodic table and also with Au, Ga, Si, Ge, Sn, P, As, and Sb. This paper describes a survey of the occurrence of the CrsO-type structure in ternary alloys having the general composition V3(B, B&apos;) where B and B&apos; are Fe, Co, Ni, Cu, Rh, Ir, Si, and Ga. The purpose of the survey was to clarify the connection between the position of the B partner in the periodic table and its CrsO-type phase-forming tenden~y.~,~ The survey is part of a broader program concerned with the influence of B-partner substitutions on the superconducting transition temperatures of CrsO-type compounds. The transition temperatures, Tc, of some of the ternary Cr,O-type phases found in the survey are also discussed in this paper. EXPERIMENTAL PROCEDURE The alloys were prepared by arc-melting in an A-He atmosphere and were in the form of buttons, weighing approximately 3 g. The metals used in their preparation were received from commercial sources and were in all cases 99.9+ pct pure. The vanadium was spectrochemically pure except for 800 ppm of Si, 200 ppm of Fe, and 200 ppm of Al. For study of each pseudobinary system at least seven alloys were prepared having the general compositions case of alloys containing gallium, melting losses were small, usually less than 0.3 pct of the total weight of the metals charged for melting. Melting losses were somewhat greater for gallium alloys, ranging in general from 0.9 to 5.0 pct. Ternary V-Si-Ga alloys were chemically analyzed and the results are given in Table I. The analyses show most alloys to be within 2 at. pct of the intended composition. Throughout the balance of the paper the intended compositions are used in discussing the alloys. The cast buttons were annealed within evacuated quartz capsules for times ranging from 3 to 6 weeks at temperatures between 800" and 1000°C and water-quenched. The phases present in the annealed and quenched alloys were identified by optical and X-ray metallography. X-ray diffraction photograms were made with powders prepared from the bulk specimens, by the use of a 114.6-mm-diam powder camera with copper irradiation. The lattice parameter of CrsO-type phases and their standard errors

Jan 1, 1963

By A. W. Fahrenwald

THE absolute efficiency of crushing and grinding in a ball mill is not known. A number of investigators have made calculations to this end and have presented efficiency figures. Two factors have prompted further investigation of this subject: (1) the unbelievably low magnitude of the values offered, and (2) a desire to obtain, if possible, true relationships between the relative efficiencies of a ball mill operating under varying conditions. A useful forward step in the study of mill efficiency was made when Martin1 and Gross and Zimmerley2 proved the correctness of Rittinger&apos;s law, and incidentally the incorrectness of the so-called Kick law, and when Gross and Zimmerley3 determined and gave surface values for Tyler sieve-sized quartz. These data are probably accurate throughout the range of the sieve scale, but on -400 mesh (which is the finest sieve available), the surface data, as obtained by the hydrofluoric acid disso-lution method, are of doubtful reliability. Any inaccuracy existing in surface determinations of -400-mesh material, especially when comparing runs in which varying quantities of this product are formed, will cause the resulting relative mill efficiency values to be distorted. Moreover, knowing surface accurately, the efficiency calculations require a surface energy figure. Two such figures are to be found in literature, one by Edser4 and one by Martin.5 Edser&apos;s surface energy

Jan 1, 1931

By C. H. Mathewson

BERYLLIUM, magnesium, zinc and cadmium, together with mercury, constitute a coherent sub-group of the periodic system and these metals, excepting mercury; have been studied in sufficient detail by the new X-ray diffraction methods to prove their common adherence to the hexagonal close-packed type of crystal structure with a progressive increase in axial ratio as we pass through the group from beryllium to cadmium. The first four columns of Table 1 summarize the data on crystal structure of these metals reported in the International Critical Tables.1 The last two columns are based on results obtained in the present investigation. TABLE 1.-Lattice Constants and Twinning Law of the Be-Cd Group of Hexagonal Metals Dimensions of Unit Axial Cell, A Ratio Description of Twinning Element a° c° (c°/a°) Composition Axis Plane Beryllium 2.28(3) 3.60(7) 1.58 {1012} Probably 1 {1012} Magnesium 3.22 5.23 1.621 ,1 {1012} Zinc 2.65(7) 4.94(8 1.86(2) 11012 } 1 {1012) Cadmium 2.98 5.63 1.88(5) {1012} Probably 1 {1012} Twinning has often been observed in zinc and cadmium. The general aspects of this twinning are abundantly illustrated by photomicrographs, diagrams, etc., in the papers by Romig, and Mathewson and Phillips reported to this Institute in 1927.2. A determination of the composition

Jan 1, 1928

By P. T. Gallagher, W. A. Oates

THE partial excess entropy of interstitial solutes in metals, SXS , has usually been interpreted as being principally vibrational ever since the initial statistical treatment of hydrogen in metals by Fowler and Smith-ells. The vibrational entropy is considered being due to the optical modes of the light interstitial atom. Little attention has been given to the magnitudes of the values of SXS&apos;. Leiser and Witte2 and Ebisuzaki and O&apos;Keeffe3 have noted that for hydrogen in metals Si is approximately constant for different metals. On the other hand if it is assumed that the interstitial solute is an isotopic defect then, as shown by McLellan, SXS should vary from metal to metal as follows: where S is the standard entropy of the solvent and Mi, M, are the masses of the interstitial and solvent atoms. respectively. Fair agreement with this equation was found for oxygen in silver and nitrogen in iron4 and for carbon in iron.= Ln a subsequent analysis of metal- hdrogen systems McLellan&apos; found a variation of $&apos; from metal to metal but not in a manner expected from the isotopic impurity equation. However, a possible correlation between the energy of solution, Ei, and sf was noted. Similar correlations have been noted for certain dilute substitutional solid Solutions 7, 8 and recently Kubaschewski 9 has demonstrated a correlation between integral heats and ex-

Jan 1, 1970

By J. J. Scott

During 1967 wage settlements and strikes ran at a high rate and it has been estimated that union gains of 4 ½ % to 5% per year have been attained in many instances. When these events are coupled with the need to operate on lower grade and deeper deposits the need for technological advances in underground mining becomes obvious. Emphasis has been on ways to reduce the number of manshifts required per ton of product. Most significant advances have been made in rapid advance of primary mine openings, development of mobile, rubber-tired, front-end loaders and hauling units, high-speed drilling with rotary and rotary percussive units and a serious look at nuclear devices to break large volumes of ore cheaply. Boring Developments in bit manufacture and metallurgy have allowed continuous boring-type machines to be used on harder formations than was deemed feasible in the past. Hecla Mining Co. has been using raise boring equipment for drilling 9 7/8 in. diam pilot holes in raises which are later reamed in an upward direction to 48 in. diam. The machine used is a J. S. Robbins model 42R raise borer which has been used successfully to drill two relatively long 48-in. diam holes. The first was 520 ft in length at a dip of 76º, and the second was a 785-ft vertical hole.

Jan 2, 1968

By Howard N. Eavenson

Waste of coal, or perhaps more properly the percentage of its recovery in mining, has keenly interested me during an experience of over a half century in coal mining. In the early part of that time and until a few years after World War I the use of better mining plans and supervision resulted in an increased recovery. Since then, and particularly since controlled prices have been effective and mechanized mining has been extensively practiced, the tendency has all been toward lesser recovery in mining. The purpose of this paper is not to criticize the methods being used, which after all are the result of economic forces, nor to point to any particular mining method or to any locality where the best recovery is obtained, but to call attention to the tremendous waste of our national coal resources that is constantly continuing. A possible method of reducing this loss will be suggested, but without any illusions that it will be followed or that such attention will be paid to it. Average Recovery The actual average percentage of recovery of coal in the ground is not known. Many papers giving figures of recovery have been published but no definite base of measurement has been agreed upon by those presenting the data. As an example, the Pittsburgh bed can be considered—it has produced a greater output than any other and has been sold or leased at higher prices in place than any other coal bed. Over a large part of its area where high prices have prevailed it has been customary for many years to draw pillars. In these mines it has been usually assumed that the average recovery was higher than in other beds and percentages of recovery of 85 to 95 per cent are usually said to be realized. In all of these mines, however, it has been customary to leave from 4 to 8 in. in the bottom, and 10 to 16 in. in the roof; thus from 14 to 24 in. of coal has been left in the mines out of a total seam thickness of about 96 in., or 15 to 25 per cent of the total coal. No attempt is made to mine this coal for metallurgical purposes, owing to its impurities, although this unmined coal is of excellent quality and better than much of the coal used for steam purposes. If we add to this discard the coal usually lost in mining and those parts of the bed &apos;that must be left because of bad seam conditions, barrier pillars, reservations for buildings, gas and oil wells, one can easily see that the actual recovery from this bed cannot be more than 65 to 75 per cent. In addition, the rooster or rider or wild coal over the mining bed—often 3 to 4 ft. of coal, high in ash and sulphur but still good steam coal—is hardly ever mined, nor is any attempt made to mine it. It is safe to say that from a broad economic viewpoint not more than 50 to 60 per cent of the fuel value of this great seam is actually being recovered.

Jan 1, 1947

By Howard N. Eavenson

Waste of coal, or perhaps more properly the percentage of its recovery in mining, has keenly interested me during an experience of over a half century in coal mining. In the early part of that time and until a few years after World War I the use of better mining plans and supervision resulted in an increased recovery. Since then, and particularly since controlled prices have been effective and mechanized mining has been extensively practiced, the tendency has all been toward lesser recovery in mining. The purpose of this paper is not to criticize the methods being used, which after all are the result of economic forces, nor to point to any particular mining method or to any locality where the best recovery is obtained, but to call attention to the tremendous waste of our national coal resources that is constantly continuing. A possible method of reducing this loss will be suggested, but without any illusions that it will be followed or that such attention will be paid to it. Average Recovery The actual average percentage of recovery of coal in the ground is not known. Many papers giving figures of recovery have been published but no definite base of measurement has been agreed upon by those presenting the data. As an example, the Pittsburgh bed can be considered—it has produced a greater output than any other and has been sold or leased at higher prices in place than any other coal bed. Over a large part of its area where high prices have prevailed it has been customary for many years to draw pillars. In these mines it has been usually assumed that the average recovery was higher than in other beds and percentages of recovery of 85 to 95 per cent are usually said to be realized. In all of these mines, however, it has been customary to leave from 4 to 8 in. in the bottom, and 10 to 16 in. in the roof; thus from 14 to 24 in. of coal has been left in the mines out of a total seam thickness of about 96 in., or 15 to 25 per cent of the total coal. No attempt is made to mine this coal for metallurgical purposes, owing to its impurities, although this unmined coal is of excellent quality and better than much of the coal used for steam purposes. If we add to this discard the coal usually lost in mining and those parts of the bed &apos;that must be left because of bad seam conditions, barrier pillars, reservations for buildings, gas and oil wells, one can easily see that the actual recovery from this bed cannot be more than 65 to 75 per cent. In addition, the rooster or rider or wild coal over the mining bed—often 3 to 4 ft. of coal, high in ash and sulphur but still good steam coal—is hardly ever mined, nor is any attempt made to mine it. It is safe to say that from a broad economic viewpoint not more than 50 to 60 per cent of the fuel value of this great seam is actually being recovered.

Jan 1, 1947

By Howard N. Evanenson

WASTE of coal, or perhaps more properly the percentage of its recovery in mining, has keenly interested me during an experience of over a half century in coal mining. In the early part of that time and until a few years after World War I the use of better mining plans and supervision resulted in an increased recovery. Since then, and particularly since controlled prices have been effective and mechanized mining has been extensively practiced, the tendency has all been toward lesser recovery in mining. The purpose of this paper is not to criticize the methods being used, which after all are the result of economic forces, nor to point to any particular mining method or to any locality where the best recovery is obtained, but to call attention to the tremendous waste of our national coal resources that is constantly continuing. A possible method of reducing this loss will be suggested, but without any illusions that it will be followed or that such attention will be paid to it. AVERAGE RECOVERY The actual average percentage of recovery of coal in the ground is not known. Many papers giving figures of recovery have been published but no definite base of measurement has been agreed upon by those presenting the data. As an example, the Pittsburgh bed can be considered-it has produced a greater output than any other and has been sold or leased at higher prices in place than any other coal bed. Over a large part of its area where high prices have prevailed it has been customary for many years to draw pillars. In these mines it has been usually assumed that the average recovery was higher than in other beds and percentages of recovery of 85 to 95 per cent are usually said to be realized. In all of these mines, however, it has been customary to leave from 4 to 8 in. in the bottom, and 10 to 16 in. in the roof; thus from 14 to 24 in. of coal has been left in the mines out of a total seam thickness of about 96 in., or 15 to 25 per cent of the total coal. No attempt is made to mine this coal for metallurgical purposes, owing to its impurities, although this unmined coal is of excellent quality and better than much of the coal used for steam purposes. If we add to this discard the coal usually lost in mining and those parts of the bed that must be left because of bad seam conditions, barrier pillars, reservations for buildings, gas and oil wells, one can easily see that the actual recovery from this bed cannot be more than 65 to 75 per cent. In addition, the rooster or rider or wild coal over the mining bed often 3 to 4 ft. of coal, high in ash and sulphur but still good steam coal-is hardly ever mined, nor is any attempt made to mine it. It is safe to say that from a broad economic viewpoint not more than 50 to 60 per cent of the fuel value of this great seam is actually being recovered.

Jan 1, 1946

By R. Sprycha, J. Szczypa, W. Janusz, J. Neczaj-Hruzewicz

INTRODUCTION Because large aqueous suspensions of various fine solids originate during the beneficiation of ores, the Mining Industry constantly requires efficient and feasible dewatering methods. Among the techniques currently in use (1,2), filtration (vacuum, press) and centrifugation are fairly expensive and thus are limited to use with more valuable materials. Furthermore, installations of reasonable size produce only moderate outputs. Therefore, tailings from ore dressing plants are usually treated by sedimentation or settling techniques with a tailings dam as the ultimate sedimentation basin (3). Apart from growing environmental and economic questions, the solid product obtained from the tailings dam basin has in most cases, a rather high moisture content and a persistent semi-fluid consistency. Thus, it is difficult to transport and use further. On the other hand, the solids may be utilized as a filling material, fertilizer, etc. providing they are dry enough and properly granulated. Demands for an improved technique are met to a great extent, by the technique presented in this paper. AGGLOMERATION OF FLOCCIJLATED SLIMES Origin and Qualitative Description of the Process Phenomena of consolidation and pellet formation in flocculated fines were first observed by Yusa and Gaudin (4) while studying rheological properties of flocculated kaolinite. On this basis, methods of separating liquid from solids have been worked out (5-7) and many possibilities for application have been suggested (5,6). Yusa termed the technique "wet pelletization&apos;&apos;.

Jan 1, 1980

By W. Hume-Rothery

IN recent interesting papers,1,2 Bardos et al. have described ternary Laves phases of the type A2(BsSi) and A4(B5Si3) where A = titanium vanadium, niobium, and so forth, and B = manganese, iron, cobalt, or nickel; other more complex formulae have also been established. In these phases, silicon plays the part of the smaller B atom of a Laves phase AB2, and the interatomic distances show that the effec- tive silicon radii lie between 1.16 and 1.21Å, and are thus very much smaller than the metallic radius of silicon for CN = 12. It does not seem to have been pointed out that these small atomic radii are almost the sape as the normal covalent radius of silicon (1.174Å). If, therefore, silicon acts as an acceptor of electrons as suggested by Bardos et al.,1 it appears to do so, not by the building up of a negatively charged silicon ion which would be large, but by the formation of what are very nearly or may be actually normal covalent bonds. Since a covalent bond contains two electrons, its formation would reduce the number of electrons available for bonding in other parts of the structure, and in this way the effect of silicon in stabilizing the o phase at high electron concentrations might be understood.

Jan 1, 1965

By C. E. Birchenall, W. Batz, H. W. Mean

AT temperatures between 1095&apos; and 1347ºC, 13 runs have been made on the diffusion of silicon in iron. In two of the runs the couple compositions were entirely within the loop of the Fe-Si system; the base alloys contained 0.0 and 1.0 wt pct Si. The other runs in which the couples consisted of a 2.3 wt pct Si alloy welded to a 3.7 pct Si alloy were a phase throughout. The alloys were made by melting electrolytic iron and commercially pure silicon. Trace impurities were not determined. The butt welded couples were diffused in an inert atmosphere of argon or hydrogen. After cooling, cuts of two mils or greater thickness were machined parallel to the weld interface. The chips were analyzed for silicon. When the concentration and distance data were examined on the conventional probability plot,&apos; no marked variation of the diffusion coefficient with concentration was indicated over the narrow composition ranges employed. Therefore, a single diffusion coefficient is recorded for each run in Table I. The temperatures and atmospheres of the diffusion anneal are listed along with the compositions of the base alloys. For a iron the silicon diffusion coefficient is given by the equation: D = 0.44 e-48,000/RT where R is the gas Constant and T, the absolute temperature. However, since the scatter in the data is fairly large, the activation energy may be in error by as much as 6000 cal per g-atom. The two ? iron points do not permit estimation of the activation energy with any reasonable certainty. They do indicate that the coefficients reported by Smithells2 and Jost,3 based on the work of Fry,4 are much too high. Although very dilute solutions in iron of manganese,5 nickel,8 cobalt,7 and molybdenum8 give dif- fusion coefficients quite close to those obtained for self-diffusion in iron, the silicon values are considerably higher, though of the same order of magnitude. This seems to be consistent with the fact that the silicon atom is the only one of those listed here which is appreciably smaller than iron. The authors are grateful to the Office of Naval Research for their support of this work under Contract N6ori-47, Task order IV, Project NR 031-184, to J. K. Stanley and the Westinghouse Research Laboratories for the silicon alloys used, to several steel companies for the silicon analyses, and to C. Wells, of the Metals Research Laboratory, Carnegie Institute of Technology, for numerous suggestions during the course of the work. References &apos;C. Wells: Atom Movements (1951) Chapter 2. A.S.M. 2C. J. Smithells: Metals Reference Book (1949) p. 405. Interscience. Pub. Co. 3W. Jost: Diffusion (1952) p. 223. Academic Press. 4 A. Fry: Stahl und Eisen (1923) 43, p. 1039. T. Wells and R. F. Mehl: Trans. AIME (1941) 145, p. 315. "C. Wells and R. F. Mehl: Trans. AIME (1941) 145, p. 329. 7M. F. Hawkes and R. F. Mehl: Trans. AIME (1947) 172, p. 467; Metals Technology (August 1947). .J. L. Ham: Trans. A.S.M. (1945) 35, p. 331.

Jan 1, 1953

By A. J. Goss, M. Tanenbaum, W. G. Pfann

THE purification of two metals, antimony and tin, by zone refining is described, and a reciprocating method of passing molten zones through a straight ingot, which effects a considerable economy of time and apparatus, is discussed. Antimony has been used extensively as a doping agent in germanium and silicon. More recently, it has become important in the preparation of new semiconducting compounds such as InSb, GaSb, and AlSb. High purity is especially necessary in this latter use, since the antimony may comprise as much as 80 pct by weight of the compound. Antimony is generally available in a commercial form of about 99.8 pct purity. Column 1 of Table I is a typical emission spectra analysis of commercially available 99.8 pct antimony. Zone refining has been quite successful in increasing the purity of such samples. Columns 2 to 4 of Table I are analyses of an ingot of the antimony of column 1 after the passage of seven molten zones in an atmosphere of nitrogen. The ingot length was 9 1/2 in.; the mean zone length was 2 in.; convection was the only means of stirring. The column headings are sample locations in inches from the leading end of the ingot. The results illustrate both the merit and a limitation of zone refining. It is seen that four of the five impurities—nickel, arsenic, lead,

Jan 1, 1955