Search Documents

By A. P. Svenningsen

DURING the work at the test mill in Morenci, it was determined that a suitable feed for the ball mills could be made by a single pass through a short-head cone crusher. These crushers did not require a closed circuit delivering only a screen product to the mills, such as is the practice in some concentrators. By no means does this mean that the practice in these other concentrators is wrong, but just that the Morenci ore can be most economically crushed and ground in this manner. Therefore, the design of the secondary crushing plant was simply a problem of taking 25,000 tons of ore per 16 hour day from the primary crusher, this ore ranging in size from fine particles to 10 or 12 in., and reducing it to minus 3/4 in. Inasmuch as outages must be contended with in any crushing plant, it was assumed that the crusher would operate at full capacity for approximately only twleve hours per day, which is three-quarter capacity for the 16-hour shift. With this in mind, it was necessary to design a crushing plant which would average approximately 1600 tones per hour for the 16-hour day, or 2000 tons per hour for slightly over 12 hours per day.

Jan 1, 1942

By M. K. Yen

The distortion of crystal structures referred to as "biege gleitung",1 "local curvature"2-4 and "deformation bands"5,6 is believed to be an unavoidable characteristic of deformed single crystals. The presence of asterism on Laue photograms of Al single crystals either deformed by pure shear7 or extended in a condition relatively free from the grip effect2 indicates strong evidence substantiating this point of view. The type of localized bending described in connection with the bending test of Al single crystals by Yen and Hibbard8 could conceivably exist either microscopically or submicroscopically in all types of deformation. The purpose of this note is to extend this idea to the postulate of a hypothetical "microbending site," as applied to the mechanism of slip in a general sense. The mosiac structure, as postulated by Darwin,9 is that crystals were actually composed of small blocks which have a linear dimension 10—4to 10-6 cm on the edge and deviate from each other by an angle of about one-tenth of a degree. The following discussion is based on the assumption that when slip is propagated from one mosaic block to the adjacent one, bending of the lattice at the region of their boundary is produced in order to maintain the continuity of the gliding process along a certain slip plane. Consider a two-dimensional diagram of two ideal mosiac blocks on the cross-section perpendicular to the slip plane and containing the active direction of slip. When an external force is applied, the localized bending or "microbending site," would be generated at the region as illustrated in Fig 1A at point B. A schematic diagram of a "microbending site," generated at a mosaic boundary, is illustrated in Fig IB. It may be seen that once the curvature of the bending site reaches sufficient magnitude, the interaction force encountered by pairs of atoms symmetrical with respect to the center of the bending is equal but opposite in sign. Consequently, the overall energy required to displace the atoms near the center is approximately zero.10"12 Based upon the finding that the misalignment between two mosaics is 0.1 degree,9 the assumption is made that "microbending sites" may possibly exist in the region where one plane will have one more row of atoms than an adjacent plane. It is probable that the origin of the bending site will be where the distance between two mosaic boundaries is "2d" as shown in Fig 1A at point B, where " d" is the interatomic distance. Thus, the distance between two "microbending sites" is in the range of about 600 interplanar spacings. In the case of aluminum, the spacing between two octahedral planes is about 2.33 A. The distance between two bending sites will be approximately 2.5 X 10"5 cm. It is interesting to note that according to Woods13 these values approach closely the size of the domains of a cold-worked metal whose minimum

Jan 1, 1950

By J. W. Downey, M. V. Nevitt

MUELLER and Knott' have reported that Ti2Cu has the Si2Mo-type (Cllb) structure. The lattice parameters of Ti2Cu and the positions of the titanium and copper atoms are given by them as follows: ao = 2.944A; co = 10.786A 6 atoms per unit cell: 2 Cu (a) 000; 1/2: 1/2, 1/2 4 Ti (e) 002; 1/2, 1/2, 1/2 + z 00 -2 ; 1/2. 1/2. 1/2- z where z = 0.341 We have found eight other binary compounds which appear to be isostructural with Ti2Cu. All of them involve the combination of a titanium group element with a copper group element or a titanium group element with palladium. The compounds and their lattice parameters are given in Table I. The alloy samples were prepared by arc melting metals having a purity of 99.9 pct or better. They were homogenized for 72 hr at 900°C in evacuated capsules and quenched in tap water. Filings were prepared, and these were reannealed for 4 hr at 700°C, also in evacuated tubes. The lattice parameters were determined by a least squares Bnalysis of the back reflection lines of patterns made with cobalt radiation. It was not possible to make a precise determination of the lattice parameters of Zr2Au because the filings underwent rapid oxidation at room temperature. The evidence supporting the large tetragonal cell containing 6 atoms involves the presence of the reflections 002, 101, 004, 112, 114, 202, and other reflections with higher indices for which I = 3n. Three or more reflections corresponding to these indices, which cannot be indexed on the basis of a small body-centered tetragonal cell containing 2 atoms, are observed in the patterns of all of the compounds listed in Table I. They are strongest and most numerous when the components have large differences in their atomic scattering factors, as is the case in Ti2Pd, Zr2Cu, and Hf2Cu. The values of the z parameter should be regarded as approximate They were selected on the basis of the best agreement between the observed intensities of two pairs of closely spaced powder pattern lines (004): (112) and (114): (202) and the corresponding intensities calculated for several values of z. An ordering scheme was assumed in which titanium, zirconium, or hafnium atoms occupy the titanium positions of Ti2Cu, and copper, silver, palladium, or gold atoms occupy the copper positions. Calculated and observed intensities of the aforementioned lines and the other lines of the patterns are in satisfactory agreement, but a refinement of the z parameters and a final confirmation of the ordering arrangement must await a more detailed study. It is interesting to note that in transition metal systems at A2B stoichiometry the Si2Mo-type structure competes for stability with two other fre-

Jan 1, 1962

By Ramesh Malhotra, Hubert E. (Deceased) Risser

THE WORLD Coal, as a source of energy and as a source of coke for the smelting of iron ore, has contributed significantly to the development of every major industrial nation of the world A number of other materials-oil, natural gas, wood, waste materials, water, and, in some applications, nuclear materials -can be used satisfactorily for the generation of heat and energy, but no generally acceptable and economic substitute has been found to supplant coke in iron ore smelting in conventional blast furnaces. In the development of many nations, coal provided the initial source of energy for industrialization Although coal provided more than 60% of the world's energy each year between 1902 and 1929, oil and natural gas have surpassed it as a source of energy in more recent years (Ref. 38, pp. 439, 441). Despite the rapid rise in importance of other fuels, a considerable amount of the total energy consumed is still supplied by coal. In 1972, coal supplied 32.1 % of the total world energy (Ref. 49, pp. 2-3). To produce this energy, 2.4 billion metric tons of coal were consumed-a 16.0% increase over the amount consumed in 1962. A further worldwide increase in the amount of coal used to supply energy is projected. According to Dr. Karlheinz Bund (Ref. 37, p 145), by the year 2000 world coal consumption could amount to 5 billion mt. Coal Resources and Production The world's coal resources are estimated to be about 10,872 billion mt. Of this amount, 1,297 billion mt are classified as measured reserves (Ref. 50, p. 57). In Table 13.A.1 the estimates of measured reserves and total resources, recent production, and the ratio of measured reserves to production of major coal-producing countries are shown. About 90% of the world's total coal resources are estimated to be in the USSR, the United States, and China. The United States ranks second in the world in coal resources, but in measured reserves, it ranks first. Because of the difference in rate at which available coal resources are being exploited, the ratio of measured reserves to actual production varies widely among areas and countries. France and East Germany have the lowest reserve to production ratios, 49.5 and 60.1, respectively. In Mexico, where currently less than 5 million mtpy of coal are produced, the ratio is 1257 For all countries producing more than 200 million mtpy of coal (except East Germany), the ratio ranges from 350 to 670. For the United States, the ratio is 669.7. In Table 13.A.2, distribution of the world's coal resources by area is shown. More than 97% of the total resources lie in the northern hemisphere, with Asia, including European USSR, having 63.4%. Only 1.9% of the total coal resources are estimat-

Jan 1, 1976

By D. A. Elgillani, M. C. Fuerstenau, M. C. Kuhn

The species responsible for flotation when xanthate is added as collector for pyrite is dixanthogen. Measured oxidation potentials of these systems show that xanthate should be oxidized to dixanthogen, and the presence of dixanthogen on the pyrite surface is confirmed by infrared absorption. Zeta potential measurements are presented and related to collector adsorption. In spite of the normal presence of pyrite in most sulfide ore deposits, only a modest amount of study has been devoted to the xanthate-pyrite flotation system in the absence of activators and depressant~.'-~ As a result, little is known about the mechanism of xanthate adsorption on pyrite. From the few studies that have been made, however, a number of significant observations have been forthcoming. For example, the dependence of flotation response on the state of oxidation of the surface was noted in two studies — one conducted by Plante and Sutherland4 and a later one by plaksin.~ In another study, Gaudin and wilkinson3 found that ferric xanthate was not present on a pyrite surface. In a later investigation, however, Gaudin' and his colleagues did extract a small amount of ferric xanthate into benzene when pyrite was ground in an evacuated mill with water, benzene, and xanthate. This quantity was apparently

Jan 1, 1969

By Orville R. Lyons, A. C. Richardson

During the past few years there has been a growing demand by coal operators for detailed information about the performance characteristics of the various dryers now being manufactured, preferably in such a form that the information could be used to determine the type of dryer best suited to a particular drying problem. A few operators have been desirous of going even further, because they are of the opinion that present-day dryers are not properly designed and that fundamental studies of dryer design should be undertaken. This growing demand for a method of dryer evaluation and the indicated need for fundamental research resulted in the sponsorship by Bituminous Coal Research, Inc. of a project at Battelle Memorial Institute to investigate the thermal drying of coal. In investigating this problem, the most feasible method of attack appeared to be a survey of active operations to determine the present status of the thermal drying of coal. Data were obtained, usually by actual plant tests with the cooperation of the various preparation engineers and their staffs, for 9 screen-type dryers, 8 rotary-type dryers, 3 continuous-pallet-type dryers, 2 flash-type dryers, I tray-type dryer, and I cascade-type dryer. The testing program provided: (I) data for 24 coal-drying operations, (2) information about the inherent characteristics of the coals dried, (3) information about the previous treatment that the coal had received, and (4) information about operating costs. The data obtained through the dryer survey and relationships determined from the data make it evident that all of the types of dryers included in the survey can be operated with the same degree of effectiveness if each type of dryer is used to dry the sizes of coal for which it is best suited. It should be noted that it is usually undesirable and often impossible to dry different sizes of coal in one type of dryer. By use of the data in the report, any prospective dryer user, having determined the surface moisture percentage and screen-size analysis of the coal to be dried, the tons of water to be removed per hour, and the final surface moisture percentage desired, should be able to determine with a fair degree of accuracy: (I) the difficulty of the drying problem, (2) the approximate cost of drying, (3) the required dryer inlet gas temperature and volume and exhaust gas temperature and volume, (4) the type of dryer to use, and (5) the size of dryer required. The method of testing the dryers and determining the difficulty of drying can be used by operators already having dryers to check the performance of their particular dryer and determine whether they are operating effectively. Considerably more information was obtained from the survey of thermal drying than was anticipated when the survey was first considered. However, a great deal of work still remains to be done in the field

Jan 1, 1949

By J. S. Aronofsky, H. J. Ramey

Potentiometric model studies of the five-spot water flood to determine the influence of mobility ratio upon injection or production histories are described. The results suggest a method for the correlation of data from field pilot tests for the estimation of an effective mobility ratio and its effect upon field water floods. The effect of the well spacing-to-well radius ratio upon production histories is presented. A method of accounting for this factor is suggested. The influence of injection (or production) rates and injection and production well pressures upon production histories is shown. The five-spot well pattern was investigated for water-to-oil mobility ratios of 0.1 to infinity. INTRODUCTION It has been well established that mobility ratio has an important effect upon flood patterns.1,2,3,4,5 It should be equally apparent that injection and production histories must also be influenced by mobility ratio. However, none of the articles referred to above mention the importance of being able to predict the effect of well pressures (or injection rates) during the entire time history of a waterflood operation. A complete description of production histories (the terms "injection" and "production" are synonymous for the steady-state model under consideration) would provide values for well pressures and interface positions at any time for a specified injection rate. conversely, if the waterflood problem is specified in terms of a constant injection well pressure, then it would be desirable to know the injection rate and interface positions at any time. This paper describes the results of potentiometric model studies which were used to analyze the influence of mobility ratio on injection or production histories. A method is presented for calculating production histories over a range of ratios of well spacing-to-well radius. The basic method described in this paper to evaluate production histories is to: (1) determine interface position as given in Ref. 1, and (2) measure electrical current and voltage drop for each interface position. It should be mentioned that the current state of knowledge on flood patterns as affected by mobility ratio shows that significant discrepancies exist between the results of various investigators2,3,4,5. It is beyond the scope of this paper to discuss the reasons for such discrepancies. However, the method of determining production histories presented in this paper could be applied to any of the swept-area patterns presented in the literature. All results given in this paper are based on a set of swept areas obtained by the potentiometric method. Potentiometric analyzer technique is adequately described in the literature, but the basic assumptions involved in work of this nature bear repetition. It is assumed that: 1. A distinct oil-water interface exists in the reservoir; only water is mobile in the region behind the interface (water zone) and only oil is mobile in the region ahead of the interface (oil zone). 2. There is a fixed mobility value, (k/µ) w associated

Jan 1, 1957

By S. K. Sarkar, B. Dr. Singh

INTRODUCTION India like USA has traditionally relied on bord and pillars as dominant underground method. Coal has generally been mined at shallow depth from relatively thick and horizontally bedded coal seams. These' factors contributed towards large scale adoption of bard and pillar. After nationalisation of coal industry in two stages in 1971 and 1973, large scale mechanisation and modernisation programmes were undertaken. Longwall mining was identified as one of the major that area for increasing underground coal production. The idea to introduce longwall mining was mooted to increase productivity and to promote conservation and safety. The nationalised coal industry has already worked about twenty longwall faces with different types of support. The tempo of introducing longwall is catching up and a number of longwall programmes with, Self advancing supports of different types and Capacity are in active stage of implementation. The country has not yet started producing mechanised Supports and therefore supports and machineries are being imported from U.K. and other countries of the continent. The of the major problem faced in the longwall projects is to choose suitable type and capacity of supports. The suppliers and manufacturers of these supports are not competent enough to choose and offer the right type and capacity of supports as their knowledge and information about Indian strata conditions are extremely limited. The Central Wining Research Station (Q.!RS), has undertaken a research programme for evaluating the rock mechanical conditions obtaining in the proposed longwall locales and has worked out a method for selection of proper type and capacity of supports on the basis of projected strata behaviour at the proposed locale. STRATA CCNTROL FAILURES Indian coal industry had made some attempts to introduce longwall caving in the early fifties after a working group set up by the Government of India had recommended its adoption to increase productivity and to modernise mines. Approximately 20 longwall faces were tried in the major Indian coalfields of Jharia, Ranigunj and Karanpurr between 1951 and 1968. The supports used consisted of 20T hydraulic props or 35140~ friction props. A number of these faces had suffered total strata control failures and a large number of support elements were lost. The Central Mining Research Station initiated a research programme to analyse these failures in the general background of behaviour of Indian coal measure strata at longwall faces. All the available data regarding the cases of failures were collected and physico-mechanical properties of overlying roof rocks were determined in the laboratory. Simultaneously, observations were continued to establish the behviour pattern of Indian coal measure strata at longwall faces. These studies were helpful in analysing the occurrences of collapse. BEHAVIOUR OF INDIAN COAL MEASURE STRATA The coal measure strata encountered in the principal Indian coalfields of Jharia, Ranigunj and Karanpura are in general strong in nature however, the immediate roof (mostly up to 1.5 to 2 m) in most of the cases is weak and false bedded shale. MI idea about the strength properties of immediate and overlying roofs may be obtained from the following table.

Jan 1, 1982

By Orville R. Lyons, A. C. Richardson

DURING the past few years there has been a growing demand by coal operators for detailed information about the performance characteristics of the various dryers now being manufactured, preferably in such a form that the information could be used to determine the type of dryer best suited to a particular drying problem. A few operators have been desirous of going even further, because they are of the opinion that present-day dryers are not properly designed and that fundamental studies of dryer design should be undertaken. This growing demand for a method of dryer evaluation and the indicated need for fundamental research resulted in the sponsorship by Bituminous Coal Research, Inc. of a project at Battelle Memorial Institute to investigate the thermal drying of coal. In investigating this problem, the most feasible method of attack appeared to be a survey of active operations to determine the present status of the thermal drying of coal. Data were obtained, usually by actual plant tests with the cooperation of the various preparation engineers and their staffs, for Q screen-type dryers, 8 rotary- type dryers, 3 continuous-pallet-type dryers, 2 flash-type dryers, I tray-type dryer, and I cascade-type dryer. The testing program provided: (I) data for 24 coal- drying operations, (2) information about dried, (3) information about the previous treatment that the coal had received, and (4) information about operating costs. The data obtained through the dryer survey and relationships determined from the data make it evident that all of the types of dryers included in the survey can be operated with the same degree of effectiveness if each type of dryer is used to dry the sizes of coal for which it is best suited. It should be noted that it is usually undesirable and often impossible to dry different sizes of coal in one type of dryer. By use of the data in the report, any prospective dryer user, having determined the surface moisture percentage and screen- size analysis of the coal to be dried, the tons of water to be removed per hour, and the final surface moisture percentage desired, should be able to determine with a fair degree of accuracy: (I) the difficulty of the drying problem, (2) the approximate cost of drying, (3) the required dryer inlet gas temperature and volume and exhaust gas temperature and volume, (4) the type of dryer to use, and (5) the size of dryer required. The method of testing the dryers and determining the difficulty of drying can be used by operators already having dryers to check the performance of their particular dryer and determine whether they are operating effectively. Considerably more information was obtained from the survey of thermal drying than was anticipated when the survey was first considered. However, a great deal of work still remains to be done in the field

Jan 1, 1948

By F. S. McNicholas

IN the writer's opinion the term "block caving" has been rather loosely applied to a general principle of mining, and therefore detailed classification of caving methods and draw, together with the characteristics required for each method, will fill a desired need. Selection of caving method should be made only after a study of all governing conditions, such as size of orebody, lateral and vertical extent of ore-body, attitude, treatment demands, possible resultant pressures, and cost and profit comparison of methods. Successful caving methods can be classified under six main headings: (1) Full-protected block caving, (2) semi-protected block caving, (3) unprotected block caving, (4) full-panel caving, (5) half block-panel caving, (6) block-panel caving. The methods and factors governing choice of method are shown in Table I. Full-protected Block Caving Full-protected block caving consists of develop-ing, undercutting, and drawing to exhaustion a block of ore of predetermined size without coordination of mining or draw with adjoining areas. The block is mined and drawn as an independent unit (Fig. 1). Full-protected block caving demands that mining and draw cannot be done against unconsolidated capping in adjoining caved and exhausted blocks. Two sides of block are against solid. Caved capping must be allowed to consolidate for a suitable period, usually not less than one year. Pillars may be left in lieu of consolidated capping (Fig. 2). The advantages of full-protected block, caving are: (1) A definite area is developed, mined, and drawn as a unit so that all work may be completed, the block drawn to exhaustion in the minimum length of time, and the area then abandoned. (? Production is not restrained because of coordina1, on with adjoining areas. (3) Records of draw and caved reserve of ore are good. Upon abanwnment of the block, accountability for production is closed out with no carry-over to adjoining areas. The disadvantages of full-protected block caving are: (1) Side dilution from the draw adjacent to the consolidated capping may be serious, particularly where capping does not consolidate sufficiently in the allotted time. (2) Boundary weakening is needed on the solid sides of the block except in weak rocks. (3) Maximum cantilever and compression effect to aid caving and fragmentation may not be secured since the draw should proceed from the solid to the consolidated capping to minimize side dilution. However, undercutting from the loose (caved capping) to the solid with a slight initial draw in the same manner will develop cantilever effect. (4) A period of at least one year, more is usually desirable, must be allowed for caved capping ,to consolidate before mining the adjoining block, depending upon the characteristics of the capping. (5) Capping may not consolidate sufficiently in the time that can be allowed. Full-protected block caving is indicated where: (1) The ground is weak and heavy and workings

Jan 1, 1952

By D. A. Dukelow, G. Derge

THE Fe0-Mn0-Si0, system has many properties of fundamental interest besides its occurrence in steel-making. The system is the simplest ternary complication of the FeO-SiO, binary whose electrochemical properties have been explored. Therefore, knowledge of the conformance of Fe0-MnO-SiO, melts to Faraday&apos;s laws, as investigated by current efficiency measurements, would be of particular value in interpreting the observed variations of electrical conductivity, while at the same time furthering understanding of this type of molten oxides. Pertinent to the present study are conductivity data of FeO-SiO, and Fe0-Mn0-SiO2, and current efficiency data of FeO-SiO,. Concerning conductivity measurements, Inouye, Tomlinson, and chipman&apos; studied the specific conductivity, a, of molten wüstite as a function of temperature and oxide addition. Liquid FeO in equilibrium with an iron crucible was found to have a o whose magnitude and positive temperature coefficient were undeniably semiconductor in nature (o1400°C = 269 ohm-1cm-&apos;). Additions at 1400°C of 5 mole pct MnO decreased o to 227 while a similar addition of SiO2, dropped o to 125. Additional SiO2 produced an exponential decline of o. It was reasoned that because wüstite is known to be oxygen excess and since there is no pronounced change in oFeO upon melting, that UFeO(L)is p-type semiconduction. Björling2 gives o data for the ternary FeO-MnO-SiO, using fayalite, 2 FeO-SiO,, as the base substance. Upon addition of tephroite, 2 MnO-SiO, he noted a small decrease in o. Taking his data for 1400°C with one-half of the fayalite replaced by tephroite, o shows a decrease of some 40 pct relative to o for fayalite, i.e., 5 ohm-&apos; cm-&apos; to 3. In line with this observation, Mori and Matsushita3 reported that substituting MnO for FeO in the silicate de- creased o slightly except at high SiO, contents where the decrease was somewhat larger. Investigating the ionic nature of FeO-SiO2 melts, Simnad, Derge, and George4, found the anode current efficiency, C,, as calculated from iron anode weight loss, was temperature invariant and in general increased with SiO2 concentration. The authors suggested the possible presence of electronic conduction to explain why C+ < 100 pct. Fig. 4 includes their results as curve (b). EXPERIMENTAL METHOD Apparatus—Fig. 1 is a schematic section of the electrolysis cell used in all the current efficiency runs. The melt was contained in an iron crucible that rested on an alundum ring. A centered silica tube came within 1 in. of the surface of the melt and initially served as a thermocouple well and then as the guide for the anode.

Jan 1, 1961

By H. W. Hitzrot, R. H. Limons, L. V. Fegan

The testing of a new method for measuring pellet-bed temperatures in the traveling-grate or shaft furnace is presented in this paper. This method, using silver-palladium alloy wires as indicators, overcomes disadvantages existing in the methods based on the use of thermocouples which are costly and time-consuming. The authors have developed and tested a new method for measuring pellet-bed temperatures in the traveling-grate or shaft turnace through the use of silver-palladium alloy wires as indicators. This method overcomes the disadvantages of existing methods, which, based on the use of thermocouples, are generally costly and time-consuming. For example, in the case of the traveling-grate furnace, the installation of an instrumented pellet, together with its attached thermocouples, requires stopping the furnace, with resulting loss of production time. As for temperature measurement in the shaft furnace by the existing method, the movement of the shuttle-car feeder seriously interferes with both the actual insertion and the resulting distribution of continuously fed thermocouples. The authors have overcome these difficulties by using, as temperature indicators, a range of silver-palladium alloy wires that can be easily recovered, after firing at any desired location in a pellet furnace. Silver-palladium wires having specific melting points from 2000°F to 2500°F are enclosed in ceramic capsules. Each capsule is placed in a ni-chrome wire basket filled with a sample of green pellets, the baskets being the means for recovering the capsule after firing. After the encapsulated wires have been exposed to the firing cycle, the alloy wires are examined to determine the maximum temperatures attained by the pellet sample. This method gives accurate, rapid determinations of maximum temperatures attained during pellet induration in either the traveling-grate or shaft furnace The new method has the following advantages over existing methods: 1) it is less expensive; 2) no furnace downtime is required; 3) the testing units can, be made in quantity in advance; 4) measurements can be made in rapid succession at all desired locations; 5) measurements of maximum firing temperatures are more accurate; 6) on the basis of points 4 and 5, the new method gives a more reliable picture of the correlation of pellet quality, petrographic textures and maximum temperatures, thus providing a more effective quality-control tool. A disadvantage of the method is, of course, that the measurements are not continuous and only maximum temperatures are determined. TEST PROGRAM Preparation of Materials: CALIBRATION OF ALLOYS - In the following discussion the term "bead point" (see Fig. 1) refers to the temperature at which each alloy begins to melt and form a bead. Fig. 2 gives the bead point curve for silver-palladium alloys. Before the alloys are used in plant tests, the bead point of each alloy should be determined in the laboratory to verify the alloy compositions. Once a given alloy has been calibrated, it can be

Jan 1, 1965

By I. Hawke, K. Barron

I. Hawkes (Postgraduate School in Mining, University of Sheffield, Sheffield, England) — The photoelastic stressmeter is proving to be a very practical tool for &apos;in-situ&apos; measurements in the fields of civil and mining engineering and Barron&apos;s article has therefore come at a very opportune time, supplementing as it does, the considerable amount of laboratory and field data which is being accumulated.1,2,3 There are however several points relating the application of Barron&apos;s conclusions to the practical use of the meter which require further elucidation. EASE OF READING If the photoelastic stressmeter is to have a wide application, the fringe orders must be easily measured. The system adopted by the writer and his colleagues at Sheffield for the uniaxial stress case is to read the fringe order at the 45 point, 0.20 in. from the center (11/4 in. diam meter). This procedure has been recommended because the fringes not at this point form a very distinct &apos;eye&apos; which is obvious even to those who have had little experience with photoelastic fringe patterns. Barron points out that this point can also be used up to a stress ratio of 0.33 and in practice this is normally done. In biaxial fields above a ratio of 0.33 the &apos;eye&apos; is no longer apparent and the fringe order must be ascertained at some other point. The writer and his colleagues experimented at various points and finally chose a point at a distance 0.175 in. (11/4 in. diam meter) on the minor stress axis and fixed this point on the meter by inserting a collar of this diameter. This procedure enables the &apos;eye&apos; technique to be used for uniaxial stresses as the &apos;eye&apos; falls outside the collar; any other technique for biaxial patterns would require lines to be engraved on the meter itself and reading difficulties would be experienced by all but the most highly trained. It is interesting to point out that in a great many field applications ranging from underground pillars to building foundation piles the stresses measured have been uniaxial. In such cases, reading the fringe order has been simple even for unskilled persons. SENSITIVITY The photoelastic stressmeter acts as an inclusion, and as such its theoretical behavior is as described by Barron&apos;s mathematical analysis. When considering its practical application, however, it must be remembered that rocks and concrete are not mathematically ideal substances. The theory relates the fringe order in the meter to the stresses and the E (Young&apos;s Modulus) and the µ (Poisson&apos;s Ratio) values of the surrounding material. There is of course no unique E or µ value for rocks or concrete. These values change both with stress level and time load application sometimes to the order of 300%. We at Sheffield have very accurately calibrated the photoelastic stressmeter in a wide range of materials and have also measured the average E values for these materials. The results prove that the meter sensitivity

Jan 1, 1965

By Edward Martinez

The literature on the beneficiation of serpentine asbestos ore states that the specific gravity of the rock containing fiber and the fiber itself is the same so that specific gravity cannot be used as a basis for separation. An investigation of particles of asbestos ore ranging in size from 4 mesh to 5 in. revealed that the fiber-bearing particles generally had a lower specific gravity compared to essentially barren particles. The difference in specific gravity was sufficient to make an effective gravity separation of ore particles and reject a low grade tailings product. The results of laboratory tests are described that lead to the running of pilot plant tests with 20-ton ore samples using a heavy media separator. These tests indicated that a large amount of low grade material could be rejected from the raw ore at a coarse size. Although the process used is a wet separation, it can be added to a conventional dry asbestos mill. A gravity preconcentration would allow the mining of lower grade ore, increase the life of the mine, increase the value of the feed to the fiber recovery section, and decrease maintenance costs by removal of low grade tailings early in the flowsheet.

Jan 1, 1975

By H. R. Ogden, A. G. Imgram, D. N. Williams

The effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. Increasing the chromium, vandium, or aluminum content increased the strength of quenched structures with chromium being the most effective strengthener. Appreciable aging response was obtained with low chromium alloys, but high chromium alloys age softened rather than. hardened. High vanadium contents had a similar effect. Aluminum additions shifted the aging behavior toward that observed in lower chromium alloys, enabling high chromium alloys to be age hardened. DURING the course of titanium alloy development many a and a-ß alloys have been evolved to commercial status. However, only one all-ß alloy has achieved this same stature. This is the Ti-13V-11Cr-3Al alloy. It is characterized by a very sluggish ß-phase decomposition reaction such that very slow cooling rates can retain the 0 phase at room temperature. In addition, very high strength levels can be obtained by long-time aging treatments. Combinations of cold or warm working followed by aging produce even further improvements in strength. This paper describes the results of a research program in which the effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. EXPERIMENTAL PROCEDURES Electrolytically refined, high-purity titanium was used as the alloy base for these studies. Iodide chromium, electrolytically refined vanadium granules, and high-purity aluminum sheet were used as alloying additions. The compositions of interest were melted as 250-g ingots in a direct current arc melting furnace under a flowing atmosphere of argon. The ingots were hot forged to 3/4-in.-diam bars, vacuum annealed for 6 hr at 1800°F to reduce residual hydrogen content, and then hot swaged to 1/4-in.-diam rods. Fabrication history, and interstitial analyses after fabrication are given in Table I. All specimens to be heat treated were sealed in Vycor capsules under a partial pressure of argon. Samples used to define the ß transus were quenched from temperatures ranging from 1350° to 1100°F after holding at temperature for 15 min. Samples for aging studies were quenched from above the ß transus temperature and then aged for up to 64 hr at 750°F and for 100 hr at 850°, 900°, and 950°F. The effects of straining prior to aging were also investigated. The results of these studies were used to select the heat treatments for the tensile specimen blanks. Heat treatments of the tensile specimens are described in Table 11. Alloys were aged after solution heat treatment or after solution heat treatment and cold swaging to 50 pct reduction in area. Standard 0.125-in.-diam tensile specimens were machined from the heat-treated blanks. All tensile tests were performed in a Baldwin-Southwark uni-

Jan 1, 1963

By G. H. Anderson

Cadmium-coppeR precipitate, a byproduct of the purification stage of the zinc plant, is composed mainly of zinc, cadmium and copper in varying amounts depending on the efficiency of precipitation and the cadmium and copper contents of the impure solution treated. The composition range is approximately: cadmium 10-12 pct, copper 6-8 pct, and zinc 3&35 pct. As received at the cadmium plant, the precipitate is a dark gray to black press cake produced by filter pressing the flocculent cadmium-copper precipitate formed when impure zinc solution is agitated with zinc dust. The details of the cadmium-copper precipitation are to be found in the paper "Electrolytic Zinc at Risdon, Tasmania," by W. C. Snow. Transactions AIME, 121, 501. The treatment, in addition to recovering cadmium as metal, yields a copper product as a residue for realization and recovers in solution for return to the zinc plant, the excess of zinc dust used during purification. The recovery of cadmium metal is approximately 200 tons† per year, but, with the amount of copper residue recovered, varies with the zinc production tonnage, composition of the original concentrates, degree of roasting and other operational factors. The operations involved in the recovery of the foregoing materials are carried out in a building adjacent to the purification section of the zinc plant and can best be described by dividing the process into the following stages: 1. Oxidation and Grinding of the cadmium-copper precipitate. 2. Leaching and Filtering. 3. Precipitation of cadmium. 4. Oxidation and Grinding of the precipitated cadmium. 5. Leaching oxidized cadmium precipitate and Purification of leach solution. 6. Electrolysis. 7. Melting, Casting and Packing. A feature of the process is the use of two distinct solution circuits. Spent electrolyte from the zinc plant circuit containing about 10 pct sulphuric acid is used as the primary solvent of the cadmium and zinc present in the oxidized precipitate. When the cadmium is later separated by precipitation and filtering, the filtrate, originally zinc plant spent electrolyte and now fortified in zinc, is returned to the zinc plant. The precipitated cadmium, after oxidation, is redissolved in spent electrolyte from cadmium electrolysis which solution is in closed circuit within the cadmium plant except for discards to the zinc plant circuit as mentioned in Section 5 hereinafter. (Fig 1.) Details of the various operations follow. I. Oxidation and Grinding of the Cadminm-copper Precipitate The precipitate having had a preliminary drying by compressed air in Dehne filter presses in the zinc plant is trucked to a storage platform of sufiicient length to store 3 to 4 days&apos; production separately. After 48 hr exposure to atmosphere, oxidation is sufficient to enable all cadmium and zinc but only a portion of the copper to be dissolved in dilute sulphuric acid. The oxidized precipitate is shovelled into trucks and, after weighing and sampling, is broken in size by means of

Jan 1, 1950

Map

Jan 1, 1958

By J. Kent Smith

Vanadium is generally spoken of as a rare element; but, even in the light of our resources as known a couple of years ago, this description could be accepted in a qualified sense only. In fact, vanadium is very widely distributed, being a constituent of most clays, while even caustic soda has been shown to contain almost regularly a minute proportion of it, although the quantity in each case is so small as to render impracticable the extraction of the metal therefrom with profit. The opening-up of a large deposit of vanadium sulphide ore in South America has put a new phase on the commercial outlook of vanadium, the technical value of which for the improrement of steel has been proved by rigorous scientific investigation. This sulphide ore has the following analysis: Per Cent. Vanadium sulphide,.39.84 Molybdenum sulphide,.1.57 Nickel sulphide,.........1.49 Iron sulphide,.........4.07 Arsenic sulphide,.. nil. Copper sulphide,.. nil. Manganese sulphide,..nil. Free sulphur,..30.57 Phosphorus,...nil. Silica,....13.60 Alumina,..........2.46 Combined water, 5.00 Carbonic acid, Lime, magnesia, potash, soda and unaccounted for, 100.00 Being a free-burning ore it is calcined with ease, losing 45 per cent. of its weight in the process. The calcined ore has the following analysis:

Jan 1, 1908

By John Burns

THE object of this chapter is to present data concerning the effect of the introduction of relatively slight amounts of carbon and nitrogen into supersaturated solution in iron. The study is confined to the alpha temperature range of both the Fe-C and Fe-N systems. The age-harden-ing characteristics of these two systems are considered. These data are compared to those of other age-hardening alloy systems and a "classifica-tion" is essayed. A.-RELATION OF LATTICE PARAMETER AND ELECTRICAL CONDUCTIVITY TO CHANGES IN PHYSICAL PROPERTIES DUE TO AGING OF FE-C ALLOYS Since Whiteley1 in 1927 showed that some of the iron carbide that is normally present in slowly cooled low carbon-iron alloys disappears on rapid cooling from just below the A1 point, interest has been manifested in the possibilities of age-hardening in these alloys. Masing and Koch,2 and at the same time and independently, W. Koster,3 proved these alloys to be age-hardenable. A. A. Bates4 a little later also published an interesting paper on changes in physical properties due to the aging of low-carbon steels. Many other papers have appeared showing changes in physical properties in specific instances due to this same phenomenon.

Jan 1, 1934

By Howard Scott, Henry S. Rawdon

The method of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallog-raphists. The usual procedure1 2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas (chlorine, hydrochloric acid or similar gas) for a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being admitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo. The studies of Rosenhain, Humfrey, and other workers 4, 5, 6, 7, 8 dem-

Jan 1, 1922