Search Documents

By G. H. Tausch, J. R. Dublin, T. A. Huber

Simplified equipment and techniques have been developed to permit cementing a completion interval in a well and recompleting higher, lower, or at the same depth in such a manner as to: 1. Eliminate the need for a conventional drilling or workover rig. 2. Eliminate mud and other cement contaminants which have long interferred with ideal cementing. 3. Eliminate need for drilling out cement. 4. Provide a more satisfactory recompletion. 5. Provide a more economical recompletion. This technique involves the use of a small-diameter, lightweight, tubing extension which is run on a wireline and set in a landing nipple previously installed in the tubing string. Low squeeze pressure and small cement volumes, with their attendant cost reduction, are successfully used when wells are completed and reworked with salt water or other penetrating fluids. Relatively low-water-loss cement is an integral component of the technique which provides that excess cement be reverse-circulated from the well to leave the casing void of cement when recompleting lower or in the same interval. Substantial cost reductions are realized by using the simplified or low-pressure cementing technique, and the ratio of successful squeeze-cement operations has been increased. Squeeze-cementing or recementing is the act of filling a channel behind casing or filling holes purposely placed in the casing. To obtain a satisfactory squeeze-cement job, it is necessary only to fill the channel or the perforation holes with a cement filter cake and to allow it to harden in that position. In the past, the presence of mud in a well has been considered the chief deterrent to obtaining a good cement bond and satisfactory cement job; however, late developments in squeeze-cementing have made it possible to eliminate cement contamination or interference. Since it is possible to form a cement filter cake with a small pressure differential, squeeze-cementing with high pressures may not be necessary in most cases. The amount of cement needed to fill the annulus about the casing and even to fill part of the casing, if necessary, is generally small in quantity. Use of low squeeze-cementing pressures and small quantities of cement provides the following advantages: 1. Longer effective life of well tubing, casing, and other equipment; and less chance of costly equipment failure due to excessive pressure. 2. Monetary savings effected by elimination of retainers and specal squeeze-cementing tools. 3. Monetary savings effected by use of small quantities of cement and fewer squeeze-cementing operations. 4. Future surface squeeze-cementing equipment may be smaller and more economical to operate and maintain.

Jan 1, 1955

By G. F. Jenkins

The word asbestos is a broad term that has been accepted and applied to a number of fibrous mineral silicates found in nature. They are incombustible and can be separated by mechanical means into fibers of various lengths and thicknesses, but differ in chemical composition and other properties. It is generally recognized that there are six varieties of asbestos; the finely fibrous form of serpentine known as chrysotile, and five minerals of the amphibole group, i.e., amosite (not fully recognized as a mineral species name but accepted in asbestos terminology), anthophyllite, crocidolite, tremolite and actinolite. (Figs 1-4.) Physical and Other Properties The structures of asbestos fibers have been studied intensely in recent years. X-ray diffraction patterns 1 to 15 have been used as a means of identification and classification. The amphibole group structures have been fairly well established while the serpentine group has been the subject of many investigations during the past six years. Low-angle X-ray scattering techniques5 have shown that the chrysotile fibrils are "hexagonally close packed" and parallel to each other, having cross-sectional diameters varying from 180Å* units to 300Å units, while the amphibole fibers are many times larger in cross section. The electron micrographs of chrysotile asbestos (Figs 1-4) have also indicated that the fibrils might be in the form of a hollow tube. This point has been the subject of considerable controversy by a number of investigators.7 to 16 Density measurements17 made on a sample of high quality Arizona fiber did not indicate that the fiber had a hollow tube structure; however, the so-called "sheet structure" of the fibril could be distorted in such a way that it gives the appearance of a hollow tube in the electron microscope. It is of interest to quote one investigator, F. L. Pundsack,17 in this connection: Although the empirical composition of chrysotile is 3MgO.2SiO2.2H20, the true unit cell[#] composition is best represented as Mg12(OH)16Si8O20. This cell has dimensions of a= 5.3Å, b = 9.2 Å, and c = 14.6 Å where the "a" direction is the fiber axis. The calculated density of this unit is 2.56 g/cc, a value in close agreement with experimentally determined density values for chrysotile. The exact manner in which the unit cells of asbestos are stacked together to build up a single fiber of chrysotile is not known, but from various

Jan 1, 1960

By R. J. Corfield

MODERNIZATION of the entire electrical system and improvement of Rotation process efficiency is the twofold goal of the improvement program underway at the Arthur and Magna concentrators of the Utah Copper Div., Kennecott Copper Corp. Copper ore from the Bingham pit goes to these two concentrators where an interlocking program calls for complete electrical modernization and increased flotation process efficiency through additional capacity and flow scheme revisions. Flotation plants at the two mills are essentially duplicates, and while this article deals with the changes at the Arthur mill similiar improvements are being made at the Magna mill.

Jan 3, 1953

By Richard McCaffery

THERE has been some discussion among blast-furnace operators regarding the relative merits of tuyeres of the converging type and tuyeres designed in an attempt to produce a diverging jet of air. An article1 on Progress in German Blast Furnace Practice indicates the interest in this subject abroad. This article illustrates a diverging type of tuyere which is shown here in Fig. 1A. The design appears to be rather poor as regards known properties of air flow. The adoption of this. tuyere, the article states, resulted in a decrease of blast pressure of about 4 lb. per sq. in. and an increase of the output of the furnace. If the improvements mentioned are due entirely to the change in tuyere design, the subject of tuyere design seemed worthy of investigation and this paper is a report of such work. Because of the gain in efficiency brought about by the use of a diverging tuyere in the German plant, it was thought desirable to investigate the shape of the air streams issuing from various-types of tuyeres to ascertain whether the gain was due to the tuyere itself or to the distribution of the air in the furnace. Since it is difficult to do experimental work on a full-sized furnace, or even on full-sized tuyeres, and because of the equipment available for the work, it was decided to carry out the work on scale models of tuyeres. Therefore, in this work, single tuyeres were used and the blast discharged into the atmosphere. The shape of the air stream was determined by means of a Pitot tube suitably supported in the air stream at various positions. The air was. furnished by a Roots blower driven by a 10-hp. direct-current motor having field control, and capable of discharging 250 cu. ft. per min. with a pressure on the discharge of 4 in. of mercury. A modern blast furnace with 21-ft. hearth requires about 50,000 cu. ft. per min. of free air at from 16 to 23 lb. per sq. in. pressure, depending upon the type of burden. This pressure is the total pressure required to force the air through the burden and through the tuyeres. Upon computation the pressure drop through the tuyeres is about 1 to 2 lb. per sq. in. By making the tuyeres to a one-fifth scale, and by using a pressure of 1.5 in. of mercury, the shape of the air streams should be

Jan 1, 1931

The following list of corrections has been compiled from the thirty-five volumes, with some additions: VOLUME I. Page 160. The first two sentences of the second paragraph should read as follows : " For No. II we find that 2.33 percent. A1,08 take 4.07 per cent. 8109, leaving 3.48 per cent. 8102 free, which requires 3.25 per cent. CaO." Page 160, line 14, 3.79 should be 3.25; and in the 15th and 18th lines, 48.44 should be 46.98. VOLUME VI. Page 59. The discharges of the miners' inch per second, given as .2624 and .2499 cubic feet, should be .02624 and .02499, respectively. The discharges per minute, hour, etc., are correctly given. VOLUME VIII. Page 214. 16th and 25th lines, ferric carbonate should be ferrous carbonate. Page 486, 16th line, 10,000 should be 5,000. [ ]

Jan 1, 1907

By R. S. Dean

THE commercial production of electrolytic manganese on a small scale commenced in 1939. The writer made a short report on the progress of production and utilization in MINING AND METALLURGY for January 1941. Progress during the last two years, naturally, has been more rapid. In June 1940, Congressman (now Senator) Scrugham presented a proposal to Congress for an appropriation authorizing erection of a pilot plant for "the production of metallic manganese by electrolytic or other means." As a result of this, a pilot plant, having a capacity of a few hundred pounds per day was built at Boulder City, Nev. Subsequent appropriations permitted expansion of the plant to about a ton per day. Much has been learned in this plant about electrolytic manganese, and the product even in its small way has found war uses of considerable importance. Meanwhile, the Knoxville plant of the Electro Manganese Corporation, the sole commercial producer, was expanded to about 4 tons per day to supply needed material for the war program. Other proposals for commercial plants have not been favorably received by the War Production Board. The Bureau reported on one such proposal by the American Alloys and Chemical Corporation. PRACTICE AT BOULDER CITY The present practice, as carried out at Boulder City, which is being described in more detail in a current paper by the Bureau staff at Boulder City, starts with a manganese dioxide ore containing about 20 per cent manganese. Currently this ore comes from the Three Kids deposit near Las Vegas. The steps for the production of electrolytic manganese, in general, are as follows: I. The manganese in the ore is reduced to MnO. 2. The MnO is dissolved from the ore in spent electrolyte, which contains about 38 to 47 grams per liter of free sulphuric acid, 135 grams per liter of ammonium sulphate, and 10 to 12 grams per liter of Mn as sulphate. In the leaching step the manganese is built back up to 32 to 36 grams per liter of Mn as sulphate; the pH is adjusted to neutral by means of gaseous ammonia and passed through thickeners. 3. The electrolyte is purified by adding H2S, which precipitates the heavy metals. After filtering, ferrous sulphate is added to the solution and oxidized with air and the solution is filtered and clarified on a precoat filter. 4. The purified catholyte is electrolyzed in a diaphragm cell using stainless-steel cathodes and lead-silver anodes. The current density is about 45 amp. per sq. ft. Current efficiencies of 60 to 65 per cent are regularly obtained.

Jan 1, 1944

By W. P. Saunders, W. R. Hibbard, G. H. Eichelman

Interest in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,' has resulted in the application of similar heat treatments to other eutectoid transformations. Studies o f the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5t6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported5 as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. Preparation of Alloys The copper-silicon alloy equilibrium diagram is shown in Fig 1. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutec-toid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct) Smith6 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker's commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.' Following the casting techniques of Krynitsky, Saunders and Stern,s the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under thc melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X K in., was annealed at 750°C for 21 hr and furnace cooled, About }{& in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. and The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1949

By Thomas W. Dawson

The H. C. Frick Coke Co. has used belt conveyers for handling coal for the last eighteen years but, until recently, only for small tonnages and over short distances. The first installations were outside the mines for distributing coal to various parts of plants. A belt conveyer was put in service at Colonial No. 4 Mine in November, 1906, to carry coal from the main hoisting shaft to a storage bin serving two blocks of beehive ovens on the other side of the valley; it was in constant service until the Colonial No. 4 ovens were abandoned less than a year ago. This conveyor was in an overhead gallery that spanned our sidings and yard tracks and the main line of the Pennsylvania Railroad. It was a crude installation, from the viewpoint of present conveyor engineering practice. It had no mechanical feeding device, the coal simply ran through a gate in the side of a bin on to the belt; but one belt on this conveyor lasted eleven years. This conveyor is about 300 ft. long center to center of pulleys. It operated at a speed of 250 ft. 'per min-and carried about 400 tons per day. On this basis, the belt life of eleven years means that not over a million and a quarter tons was carried by the belt. whi1e: this is not a large tonnage, the cost per ton was much less than by any previous method in use for supplying coal to ovens located at a distance from the main shaft. The next belt conveyor was installed at Bridgeport Mine in 1907. It carried about the same daily tonnage as the first, delivering from the hoisting shaft to a coke-oven bin. Very few data were kept on this conveyor. It also operated until the coke ovens at the plant were put out of blast and the coal taken to the Clairton byproduct plant by river. In 1916, work was started to equip the Bridgeport, Palmer, Gates, and Ronco mines to load their entire output on the river for transportation to the Clairton byproduct plant, which was then being built. These mines were all operating at that time and had a large area of coal available for river shipment. The Monongahela Railroad was located between the hoisting shaft and the river at each of these plants and, therefore, had to be crossed at each location to deliver coal to the river. After careful study, it was decided to transport this coal from the hoisting shaft to the river at each of these plants by belt conveyors.

Jan 1, 1925

By H. O. Hofman

Discussion of the paper of H. O. HOFMAN and JOHN BLATCHFORD, presented at the New York meeting, February, 1916, and printed in Bulletin No. 109, January, 1915, pp. 91 to 97. ROBERT H. RICHARDS, Boston, Mass.-I should like to ask Professor Hofman whether he is able to roast his stibnite without any comparatively large amount of loss of antimony? H. O. HOFMAN, Boston, Mass.-Yes. The last statement I made was that the loss of antimony, during those tests, increased with the temperature, and that up to 372° C. there was no loss whatever in antimony, also that it increased to 4:2I per cent. with 545° C., the highest temperature that we obtained in our small furnace. ROBERT H. RICHARDS.-I should like to ask a second question, and that is, is it not true that stibnite can be roasted more completely than any other sulphide?

Jan 5, 1916

By R. G. Fenish

THE B-Ni system was chosen for this study because of the great interest being shown in boron-fiber-strengthened composite materials. Boron fibers were obtained from Texaco Experiment, Inc. They average 4.2 mils in diam with a 0.5-mil tungsten wire in the center. In order to make the diffusion couple, the fibers were included in the nickel matrix by electroforming. The samples were placed in a preheated furnace for the desired temperature and length of time. Sectioning and polishing the samples revealed concentric rings as shown in Fig. 1. The average penetration distance, X, was calculated by measuring the radius of the second phase (the white shell in Fig. 1) and subtracting the original radius. The second phase was identified as NiB by X-ray diffraction. This allows the kinetics of the formation of the phase NiB to be calculated by Eq. [I], which is taken from Hoffman:"

Jan 1, 1967

By Arthur Tauber, Horst Kedesdy

FERRITES are sintered metallic oxides of the spinel structure type1 and belong to the class of soft ferromagnetic materials. Similar to a ceramic, they can be formed and fired to a dense body, exhibiting a high electrical volume resistivity ranging from 102to 107 ohm-cm as compared with 10-6 ohm-cm for some of the metallic magnetic materials. This high resistivity, with resulting low eddy current losses, finds special application at high frequencies. The dispersive susceptibility of ferrites at microwave frequencies has also led to many applications in this field. Ferrites are used in low frequency applications where high resistivity with high permeability is desirable. During the last few years ferrites exhibiting rectangular hysteresis loops have been developed for computer and magnetic memory systems. The general formula for ferrites is MeFe2O4 where Me is a divalent metal ion such as Ni, Zn, Mg, Mn, Cu, Cd, and Fe. Only two of these ferrites are nonferromagnetic, namely, those with Zn and Cd. Solid solutions can be formed between different ferrites, and it is of interest to note that solid solutions of a ferromagnetic ferrite with a nonferromagnetic ferrite yield much better magnetic materials than the basic ferrite body. In general, it can be said that the solid solution formation between ferrites has widened the field of ferrite synthesis and has led to methods of preparing materials with a large variety of magnetic properties. During the last two decades the synthesis of ferromagnetic oxides has been the object of extensive research, but commercial production has been started only within the last ten years. Along with more fundamental studies, there remains the never- ending task of developing ways to realize the optimum characteristics of materials in large-scale production. Ordinarily, to produce a ferrite material it is necessary for the constituent oxides to be mixed intimately, pressed, and then fired at temperatures above 1000°C. Ferrite Synthesis: Formation of a basic ferrite by solid state reaction from Fe2O3 and a monoxide such as NiO, under normal atmospheric conditions, is governed by a progressive diffusion of cations between adjacent particles of the constituents. Firing temperature, furnace atmosphere, and cooling can vary the magnetic properties, however. If, for example, a dioxide, a sesquioxide, or an oxide of the Me3O4 type is substituted for the monoxide, the reaction mechanism becomes more complex and extremely dependent on atmospheric conditions and firing cycles. For this reason reproduction often

Jan 1, 1958

By C. E. Arnold

A brief description of this installation was included in a recent paper by H. Kenyon Burch.l The purpose of the present paper is to amplify Mr. Burch's description, as it is felt by the writer that the subject merits more than passing attention. In making a comparison between the common method of hoisting men in mine shafts, and elevator practice in high buildings, the former shows to great disadvantage both as regards safety measures and smoothness of operation. It is surprising that in view of the inducements offered, the step of applying the building equipment direct to the mine shaft has not been taken before, as in many respects the conditions of service are similar, and the objects to be attained are identical. Even without doing this, it is certain that safety to life and limb in the usual method of hoisting men underground can be greatly enhanced by the application to the mine hoist of some of the features of the building elevator. In the case under consideration, the elevator cage runs in a vertical, concrete-lined shaft compartment 5 ft. 11 in. by 5 ft. 6 in. (1.8 by 1.68 m.) in section and 585 ft. (178 m.) deep, while the counterweight runs in the pipe and ladder compartment of a twin shaft 102 ft. (31 m.) distant. The section of the division of this compartment occupied by the counterweight measures 2 ft. 4 1/4 in. by 3 ft. 101/2 in. (0.72 by 1.18 m.), and the counterweight is made in the form of a small cage which suffices to carry two men for the purpose of making inspections or repairs in the pipe and ladder way. The hoist is designed to carry a load of 7500 lb. (3401.94 kg.), ex-clusive of the cage, which weighs 7500 lb., at a maximum speed of 800 ft. (243 m.) per minute. It is installed in the main hoist and compressor building about 220 ft. away from the elevator shaft and is driven by a 160-hp. direct-current motor which is served by a 190-hp. motor generator set. A small direct-current generator mounted at the end of the motor generator set furnishes the current for the controller magnets, brake and fields of the hoist motor and generator. The drum, which is 72 in. (1.83 m.) in diameter, is driven through the medium of a single reduction herringbone gear. A Francke flexible coupling connects the

Jan 1, 1918

No. 484.-A mining engineer and geologist of long and varied experience in North and South America is open for an engagement. Exploration and development work preferred. Rare minerals a specialty. No. 485.-Member, mining engineer, technical graduate, married, age 28, exempt, with 9 years experience at gold and silver, copper, lead, and coal mines, 4 years with present employers, is open for engagement as mine superintendent or foreman, or in charge of cyanide plant. Boston or New York interview after Oct. 10. Present position, day foreman at producing gold-silver mine in Montana. References. No. 486.-Member, age 34, married, varied experience in iron, copper, nickel, talc, etc., principally as surveyor, mine and surface geologist, and superintendent of explorations, is open for engagement. Preference, connection with some eastern consulting engineer or firm of engineers. No. 487.-Member, mine superintendent, 18 years' experience in the West and in the Lake Superior districts. Thorough business and technical training. Personal interview, preferably Chicago.

Jan 10, 1918

By Galen H., Clevenger

THE first and most important thing that affects the majority of lead producers in the Rocky Mountains and the western mining regions is that zinc in an ever-increasing degree is inseparably associated with the lead. The Sullivan mine in British Columbia is not only a great lead mine, but also a great zinc producer. This mine could not reach its full measure of productiveness, nor was its great value established, until a reasonably good physical method was developed for separating the lead from the zinc prior to the recovery of each metal by an appropriate process. The western metallurgists and also metallurgists in other parts of the world have long faced the lead-zinc problem. This for many years stimulated a great deal of experimental work looking toward the development of a physical or chemical method of separating lead and zinc in concentrated form from complex ores. Space will not permit of going into this work in detail, but it is sufficient to say that with but few exceptions the western lead smelter continued smelting charges many times too high in zinc for the most efficient operation of lead furnaces. The zinc was not only lost, as the zinc content of many a western slag dump bears mute testimony, but the cost of lead smelting was increased by reason of the presence of the zinc. The owner of the ore under these circumstances could be paid nothing for the zinc and, indeed, he was penalized for it

Jan 1, 1926

By Otto H. Henry, Edward L. Badwick

Up to the present time, according to Hansenl and Haughton,² the constitution of the bismuth-indium system has not yet been published. The generally accepted value for the melting point of indium, as listed in most scientific journals and textbooks, is 155°C. Recently, however, H. M. Davis3 has determined a new melting point for indium of 157.3²C O.l°C. Since bismuth has been used in preponderance as an alloying element in the majority of low-melting alloys, and indium has been used with considerable success in lowering the melting points of low-melting alloys, 4,6 an interest has been developed in the application of these two metals, making a complete knowledge of the constitution of its alloys desirable. In this investigation, the melting point of indium reported by H. M. Davis has been found to be substantially correct. A value of 157. ²°C ± O.5°C was determined. The two eutectic compositions have been placed at 34 and 50 pct bismuth with their respective eutectic temperatures as 72.4°C ± 0.5°C and 90°C ± 0.5°C. The bismuth-indium phase diagram has been determined by thermal and microscopic analysis and is shown in Fig I. Thermal Analysis Granulated bismuth and indium shot, having a guaranteed purity of 99.99 and 99.95 pct, respectively, were melted in a carbon crucible by means of a laboratory heater. To minimize oxidation of the alloys, a heavy mineral oil (Nujol) having a high- flash point was used. A platinum-platinum rhodium thermocouple of fine wire encased in a thin-walled Pyrex glass tube, about 1/8 in. in diameter, was connected to a type K potentiometer for temperature measurements. The thermocouple was calibrated against the melting points of tin, bismuth, and the silver-copper eutectic and the boiling point of water. Since the temperature readings could be reproduced to 0.²°Cl and the accuracy of the temperature standards in this range is slightly better than 0.5°C, it scems reasonable to assume that the temperature readings are reliable to approximately 0.5°C. The cooling rate could be controlled by varying the amount of insulation surrounding the crucible. Three or four layers of asbestos paper, 1/16 in. thick, sufficed to give a cooling rate of from I° to ²°C per minute. Undercooling was slightly noticeable. This condition was minimized by vigorous stirring, since the advantage of using slower rates was too small to justify the greater expenditure

Jan 1, 1947

By Otto H. Henry, Edward L. Badwick

Up to the present time, according to Hansenl and Haughton,² the constitution of the bismuth-indium system has not yet been published. The generally accepted value for the melting point of indium, as listed in most scientific journals and textbooks, is 155°C. Recently, however, H. M. Davis3 has determined a new melting point for indium of 157.3²C O.l°C. Since bismuth has been used in preponderance as an alloying element in the majority of low-melting alloys, and indium has been used with considerable success in lowering the melting points of low-melting alloys, 4,6 an interest has been developed in the application of these two metals, making a complete knowledge of the constitution of its alloys desirable. In this investigation, the melting point of indium reported by H. M. Davis has been found to be substantially correct. A value of 157. ²°C ± O.5°C was determined. The two eutectic compositions have been placed at 34 and 50 pct bismuth with their respective eutectic temperatures as 72.4°C ± 0.5°C and 90°C ± 0.5°C. The bismuth-indium phase diagram has been determined by thermal and microscopic analysis and is shown in Fig I. Thermal Analysis Granulated bismuth and indium shot, having a guaranteed purity of 99.99 and 99.95 pct, respectively, were melted in a carbon crucible by means of a laboratory heater. To minimize oxidation of the alloys, a heavy mineral oil (Nujol) having a high- flash point was used. A platinum-platinum rhodium thermocouple of fine wire encased in a thin-walled Pyrex glass tube, about 1/8 in. in diameter, was connected to a type K potentiometer for temperature measurements. The thermocouple was calibrated against the melting points of tin, bismuth, and the silver-copper eutectic and the boiling point of water. Since the temperature readings could be reproduced to 0.²°Cl and the accuracy of the temperature standards in this range is slightly better than 0.5°C, it scems reasonable to assume that the temperature readings are reliable to approximately 0.5°C. The cooling rate could be controlled by varying the amount of insulation surrounding the crucible. Three or four layers of asbestos paper, 1/16 in. thick, sufficed to give a cooling rate of from I° to ²°C per minute. Undercooling was slightly noticeable. This condition was minimized by vigorous stirring, since the advantage of using slower rates was too small to justify the greater expenditure

Jan 1, 1947

By W. J. Millard

VAGUE rumors and stories have been heard, from time to time, about the diamond and gold deposits of southern Venezuela. It is perhaps appropriate, at this time of revived interest in gold mining, to publish a few facts in regard to this country, which has been undergoing exploration since the fifteenth century. Gold and diamonds are found principally in the State of Bolivar which lies in southeastern Venezuela and is bounded by British Guiana on the east and Brazil on the south (see Fig. 1). The famous Mt. Roraima is situated at a point where these three countries meet in a common point (see Fig. 2). Some gold is also found in the southern part of the territory of Amacuro. Good oil prospects exist in the northern part of this same territory. Diamonds are found on the Caroni river from Rio Paragua to the village of Guri. Another small district is on the headwaters of the Cuyuni river. Quartz veins containing gold are chiefly exploited in

Jan 1, 1931

By J. N. Hobstetter, J. J. Becker

Deformed copper single crystals exhibited, upon annealing, a recrystallized twinned grain with a twin plane parallel to an active deformation plane, rotated approximately 22" about its pole, or else did not recrystallize at all. If extraneous deformation was not carefully removed, no simple orientation relationship was found. RECRYSTALLIZATION textures have been a subject of practical interest for many years, but any real understanding of their formation will have to start with a study of the recrystallization of carefully deformed single crystals. Some efforts have been made in this direction,'-' but much more experimental information is needed before a satisfactory picture of the crystallography of recrystallization can be formed. This paper reports a few results in copper single crystals. The crystals studied in this investigation were grown by the Bridgman method," and their orientations determined by the back-reflection Laue technique." Some specimens were simply deformed in compression, others were sheared, and still others tested in a rotating-grip device, in attempts to remove end constraints. The details of their deformation behavior are described elsewhere.' The deformed specimens were annealed and the orientations of the recrystallized grains were determined optically, as described by Barrett and Levenson.8 Compressed Specimens Specimen 17-A, whose orientation is given in Fig. 1, was compressed to a total of 19 pct. As observed before,' increasing deformation took place by increasing density of slip lines in initially formed clusters, with little if any formation of new slip clusters in unslipped areas. The specimen was then etched in nitric acid until its length had been reduced from 0.766 to 0.735 in. It was annealed at 1000°C, in increments of a few minutes. After 63 min, two small grains had appeared in the center, Fig. 2. They were found to be twinned with respect to each other (AB, Fig. 4). After 30 min more, the specimen was completely recrystallized. A typical view of it is given in Fig. 3. A summary of all orientations found is given in Fig. 4, in which the prominent grain G is in (001) standard projection, and the poles of the active slip planes after deformation are indicated by SP (primary slip plane), CrSP (cross-slip plane), and CnSP (conjugate slip plane). All the orientations found were related through seven orders of twinning. A "family tree" of these twins is given in Fig. 5. Furthermore, the BG twin composition plane lies close to the cross-slip plane

Jan 1, 1954

By Otto H. Henry, Edward L. Badwick

Up to the present time, according to Hansen1 and Haughton,2 the constitution of the bismuth-indium system has not yet been published. The generally accepted value for the melting point of indium, as listed in most scientific journals and textbooks, is 155°C. Recently, however, H. M. Davis3 has determined a new melting point for indium of 257.3°C ± 0.1°C. Since bismuth has been used in preponderance as an alloying element in the majority of low-melting alloys, and indium has been used with considerable success in lowering the melting points of low-melting alloys,4,5 an interest has been developed in the application of these two metals, making a complete knowledge of the constitution of its alloys desirable. In this investigation, the melting point of indium reported by H. M. Davis has been found to be substantially correct. A value of 157.2°C ± 0.5°C was determined. The two eutectic compositions have been placed at 34 and 50 pct bismuth with their respective eutectic temperatures as 72.4'C ± 0.5°C and 90°C ± 0.5°C. The bismuth-indium phase diagram has been determined by thermal and microscopic analysis and is shown in Fig I. THERMAL ANALYSIS Granulated bismuth and indium shot, having a guaranteed purity of 99.99 and 99.95 pct, respectively, were melted in a carbon crucible by means of a laboratory heater. To minimize oxidation of the alloys, a heavy mineral oil (Nujol) having a high flash point was used. A platinum-platinum rhodium thermocouple 0f fine wire encased in a thin-walled Pyrex glass tube, about 1/8 in. in diameter, was connected to a type K potentiometer for temperature measurements. The thermo-couple was calibrated against the melting points of tin, bismuth, and the silver-copper eutectic and the boiling point of water. Since the temperature readings could be reproduced to 0.2°C, and the accuracy of the temperature standards in this range is slightly better than 0.5°C, it seems reasonable to assume that the temperature readings are reliable to approximately 0.5°C. The cooling rate could be controlled by varying the amount of insulation surrounding the crucible. Three or four layers of asbestos paper, 1/16r, in. thick, sufficed to give a cooling rate of from 1° to 2°C per minute. Undercooling was slightly noticeable. This condition was minimized by vigorous stirring, since the advantage of using slower rates was too small to justify the greater expenditure

Jan 1, 1947

By C. R. St. John, R. W. Lindsay, Charles R. Austin

Many of the factors influencing the creep behavior of ferrous alloys have been investigated and reported upon in the literature, including such variables as grain size, steelmaking practice, nature and stability of the microstructure, and the effect of alloying elements in steels. However, with respect to the latter, the microstructures involved are usually heterogeneous and as a result the effect of the addition is related to its effects on the various phases present in the microstructure. In the instances where this structure consists of ferrite and carbide, the behavior of the alloy addition will be related to its action in strengthening ferrite and in opposing temperature softening of ferrite as well as coalescence of carbide. The present paper is the third in a series comprising a comprehensive review of investigations on the properties of iron binary alloys.l,2 Its purpose is to describe the results of isolating one microstructural phase, namely ferrite, and studying its creep characteristics in both the unalloyed and alloyed conditions. This should aid in establishing to a large degree the importance of ferrite in the creep behavior of steels consisting of the previously mentioned ferrite-carbide aggregate. In view of the fact that the present investigation deals only with the effects of silicon, manganese, chromium, molybdenum, nickel, and cobalt, and to a certain extent with the effects of carbon, the review of previous literature will be confined to these elements. Practically no references were encountered dealing with the influence of these elements on the creep characteristics of the isolated phase. However, various contributions have dealt with the creep behavior of low-carbon steels alloyed with the elements under consideration. A particularly concise review in this respect is given by Bullens (Battelle)= and much of this material has been drawn upon. The definite improvement in creep resistance and high-temperature strength conferred by molybdenum is well known. Published suggestions by the A.S.M.E.4 permit of an increase of some 2000 to 5000 lb. per sq. in. in permissible design loads over a temperature range from 650" to IOOO °F. as a consequence of additions of 0.40 to 0.60 per cent of this element in carbon steels of the order of 0.25 to 0.35 per cent carbon content. Babcock and Wilcox Tube CO.5 has published data showing the pronounced increase in stress necessary to cause one per cent creep per 10,000 hr. when additions of 0.5 or I per cent molybdenum are made to a plain carbon steel. These data apply to temperatures over a range from 800° to1000°F. 4

Jan 1, 1945