Search Documents

SEC. 1. The membership of the 'Institute shall comprise six classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6, Rocky Mountain Members. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members.

Jan 1, 1932

By N. Mao

This paper presents the results of a research effort to develop a technique for estimating in situ stresses by measuring stress-induced velocity anisotropy around a borehole. Relevant parameters required to make the estimate were identified and measured in the laboratory on a 35.6 cm (14.0 in) cube of Nugget sandstone with a 10.2 cm (4.0 in) diameter hole, under biaxial loading. Two pairs each of radially and tangentially polarized transducers were placed inside the hole with displacement directions either parallel or perpendicular to the principal stress directions. With this configuration, relative travel times were measured by both a pulsed phaselocked loop technique and a cross correlation of digitized waveforms. The biaxial velocity data were used to back-calculate the applied stress. The standard deviation of the differences between the calculated and applied stresses is 0.62 MPa (90 psi) for a stress level up to 8.63 MPa (1250 psi).

Jan 1, 1984

By B. B. Rath, Hsun Hu, R. S. Cline

FOLLOWING the techniques used by Beck and co-worker~ "~ the characteristics of selective growth in the recrystallization of a zone-refined aluminum single crystal, rolled 80 pct at -78°C in the (110)[112] orientation, have been studied. The material was 99.999+ pct pure. The as-grown crystal had a resistance ratio, R(298°K) /R(4,2°K), of approximately 5000. The method of preparation of the single crystals and the necessary precautions in handling them during rolling in order to avoid recrystallization in locally distorted regions were described in an earlier paper.3 The rolling texture of this zone-refined aluminum crystal is practically identical with that of less pure aluminum crystals rolle! in the same orientation, i.e., a very sharp (110)[112]. Random nuclei were provided by artificial nuclea-tion by abrading one face of the rolled crystal on 600-grit emery paper in a random fashion. The thin layer of disturbed metal recrystallized at room temperature into fine grains almost immediately. An X-ray diffraction pattern was taken from the abraded surface of the crystal, and the relative intensities of the various reflection peaks were compared with those obtained from a powder specimen. As shown in Fig. 1, the relative intensities of the various peaks from the recrystallized layer varied somewhat from experiment to experiment, depending presumably on the abrading technique. However, the texture of the recrystallized layer produced by this method is nearly as random as that of a powder specimen. Fig. 2 shows the texture determined from the "growth side" (face opposite the abraded surface) of the crystal after it was kept at room temperature for 100 hr. The specimen was only partially recrystallized, as shown by the remaining deformation texture. The new orientations are derived from the recrystallized grains grown through the thickness of the crystal from the "nucleation side" (the abraded surface). Fig. 3 shows the texture after complete recrystallization produced by annealing at 60°C for 1 hr. The arrows indicate 40-deg rotation around the (111) axes of the deformation texture. The microstructure of a completely recrystallized specimen is shown in Fig. 4. As shown in Figs. 2 and 3, the texture of the re-crystallized grains grown from the nucleation side to the growth side is essentially the same as that observed in less pure aluminum' (99.994 pct) and dilute alloyz crystals rolled in the same orientation. How-

Jan 1, 1968

By George Comstock

THESE notes should be considered as a further discussion of Mr. S. W. Miller's paper on "Some Structures in Steel Fusion Welds."1 In that paper and the resulting discussion; several conflicting opinions were expressed as to the identity of the needles or small crystals present in oxyacetylene and electric welds. An interesting specimen of an electric weld examined by the writer seems to afford new evidence regarding the needles, that may be worth presenting at this time. The specimen consisted of a piece of 3/8 -in. (9.5-mm.) steel plate, about 2 ¼ by 1 ¾ in. (5.7 by 4.5 cm.) in size, on which some iron had been deposited by arc-welding to a depth of about 3/16 in. (4.7 mm.). The weld appeared to be a very good one, with no noticeable break or boundary between the plate and the deposited iron. Sections for microscopic examination were cut in three planes at right angles to each other through the deposited metal, two of these sections also extending through the steel base. After polishing in the usual way, the microscope showed that the deposited metal was full of very small, round, gray, oxide spots, while the steel plate contained quite a number of alumina inclusions and a little slag. The sections were etched with nitric acid in ordinary alcohol, and structures similar to those described by Mr. Miller were then displayed. Fig. 1 shows the typical appearance of the deposited metal, which was quite uniform in all three of the planes examined. The round dark-gray spots are oxides, and the pale angular crystals are evidently what, Mr. Miller called cementite and Mr. Jeffries martensite, while Dr. Ruder and Prof. Boylston suggested that they might be nitride. The boundary between this structure and the steel base was sharply defined under the microscope. Fig. 2 shows the structure of the plate just under the weld; this is almost martensitic and resembles a coarse-grained casting. This coarse cast structure soon became finer as the distance from the weld increased, finally, becoming very fine, with numerous small particles of sorbite. This very fine structure, shown in Fig. 3, became coarser in turn and finally merged into the original normal structure of the steel plate, shown

Jan 1, 1919

By Robert D. Gunn, John E. Boysen, Dennis D. Fischer

The second underground coal gasification experiment conducted by ERDA's Laramie Energy Research Center at a site near Hanna, Wyo., was completed on Jul. 30, 1976. During the experiment production reached 0.32 blm3/d (12 M cu ft/d) of 6.9 w/m3 gas (175 Btu per cu ft). Approximately 6100 tonnes (6700 tons) of coal were gasified during the experiment. Energy return ratios of 4.5 to 5.3, coal gas thermal efficiencies of 76 to 89%, and overall process efficiencies of 65 to 74% were achieved during the second Hanna experiment. This paper describes the experiment and the results obtained with emphasis given to the determination of the energy recovered relative to energy consumed in conducting the test. Data from this determination are compared with previously published data from the first test conducted at Hanna during 1973-74.

Jan 1, 1978

By M. R. Tek, K. H. Coats, D. L. Katz

The performance of a gas reservoir su,bject to water drive is often affected by interference due to gas procluction or injection in neighboring reservoirs adjacent to a common aquifer. Field data available on production-pressure behavior of several reservoirs indicate that prediction of reservoir performence must include the effects due to mutual interference. A method developed to predict the performance of two or more interfering gas reservoirs, subject to specified production-iniection .rchedule.s, is presented. The method involves the comhinatiorz of the theory of unsteady-state water movernent with appropriate meterial balance consideration.s. The procedure which extends M. Mortada's treatment for interfering oil reservoirs makes use of his dimen-.sionless pressure drop quantities. prevented graphically in the literature. In order to evaluale the predictive accuracy and practical field applicability of the theory, the method has been applied to analyze the performance of two actual gas reservoirs in mutual interference. The calculations were performed on an IBA4 704 computer. The predicted performances were alro calcltlated with the interference effects ignored. The results show that considerably better agreement between calculated and observed behavior ic. obtained when the interference effects are included. INTRODUCTION Fluid communication between any number of oil or gas reservoirs adjacent to a common aquifer results in mutual interference effects on their production-pressure behavior. The theory, application and interpretation of pressure build-up behavior of oil wells, drawdown tests on oil or gas-producing formations and behavior of several storage reservoirs indicate ample experimental evidence of mutual interference. A method developed to compute the behavior of interfering oil reservoirs was published several years ago by Mortada.4 Studies conducted during the recent years on underground storage of natural gas clearly indicated the need for extending Mortada's work to the case of interfering gas reservoirs. The adoption of appropriate material balance equations in conjunction with the unsteady-state pressure interference theory yields pressure-explicit equations. Their solution, their application to a specific case history and an over-all evaluation of the developed method through the comparison of predicted and observed field performances were the main objectives of this study. DEVELOPMENT OF MATHEMATICAL RELATIONS The diffusivity Eq. 1 governs planar, radial, unsteady-state compressible liquid flow through a porous medium. ?p/?r2+1/r ?p/?r=µFc/k ?p/?t (1) The 1iterature1,2,3 contains derivations and solutions of

Sec. 1. The membership of the Institute shall comprise six classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members. All shall be equally entitled to the privileges of membership, excepting that no member of any class whom residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the claw of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members.

Jan 1, 1941

Sec. 1. The membership of the Institute shall comprise six classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members. All shall be equally entitled to the privileges of membership, excepting that no member of any class whom residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the claw of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members.

Jan 1, 1939

By E. C. W. Perryman

IN spite of the large amount of work which has been carried out on the recrystallization of aluminum and its alloys, there has been no complete investigation of the recrystallization characteristics of A1-Mg alloys. The most complete investigation is that reported by Bungardt and Osswald' who, working with commercial-purity materials, found that the temperature both of beginning and of complete recrystallization increased with magnesium content up to about 2 pct Mg, then decreased with a further increase in magnesium up to 5.0 pct, and thereafter increased again. Michaud and Segolz working with 99.93 pct A1 also found the temperature of beginning of recrystallization to decrease as the magnesium content increased from 2.13 pct to about 4.5 pct. Chossat3 using aluminum of 99.99 pct purity found that 0.12 pct Mg had no effect but that 0.4 pct Mg increased the recrystallization temperature by about 30°C. That no effect was found for 0.12 pct Mg does not agree with the later results reported by Demer and Beck4 who found that 0.025 pct Mg in 99.99 pct A1 increased the time for complete recrystallization and furthermore increased the activation energy for the recrystallization process. Kratz" using 99.997 pct A1 found that 0.5 pct Mg increased both the temperature of beginning and of complete recrystallization by 100°C. Chadwick and Hooper" working with commercial-purity material found that 1 pct Mg increased the temperature of complete recrystallization by about 40 °C for cold reductions in the range 17 to 72 pct. With smaller amounts of cold work produced by stretching (10 pct strain), they found no significant effect of magnesium. The latter result agrees with that obtained by Williams and Eborall' who found no effect of 2 pct Mg on the recrystallization temperature of commercial-purity aluminum strained 10 pct or less by stretching. Experimental Procedure Material Used: The chemical analyses of the materials used throughout this investigation are given in Table I. Fabrication: The alloys were cast in iron molds which had been washed thoroughly with alumina. After scalping, the ingots were annealed for 16 hr at 450°C, pressed, annealed at 450°C for 16 hr and hot rolled to 0.25 in. After hot rolling, the slabs were alternately annealed and cold rolled to 0.036 in. Cold-rolling reductions between intermediate anneals were kept at about 30 pct and a high intermediate annealing temperature of 450°C was used so as to obtain, as nearly as possible, similar starting grain sizes for the different materials. All intermediate anneals were done in a salt bath and were followed by cold-water quenching so as to retain all the magnesium in solid solution. The final cold reductions investigated were 20, 30, 40, 50, 60, and 80 pct. The initial grain sizes, that is, the grain size before the final cold reduction, were all very similar. Annealing Procedure: Specimens, 1 in. sq, were cut from the 0.036 in. sheet and annealed in a salt bath, the temperature of which was controlled to k2"C. Separate specimens were annealed for different times at 350°, 375", 400°, and in one or two cases at 415°C and after annealing were quenched in cold water. The time taken for a specimen to reach temperature was approximately 5 sec. Metal-lographic examination after annealing showed that no precipitation of Mg+413 occurred during cooling. Procedures Used for Determining Recrystallization Characteristics: All specimens were electrolyti-cally polished and etched by the method described previously1° and polishing was continued until about 0.002 in. had been removed from each side of the specimen. Using this technique, the smallest recrys-tallized grain which could be observed with cer-

Jan 1, 1956

By C. N. Reid

In the course of annealing studies on molybdenum, it has been observed that a carbide precipitates preferentially on internal and external surfaces. The evidence for this is as follows. Electropolished bend specimens prepared from two grades of commercial molybdenum were loaded in a closed but unsealed tantalum can, and were annealed for 1 hr at 2000°C under a vacuum of 1 x 10-4 torr. The compositions of these materials are summarized in Table I. The samples were then slowly cooled at an average rate of 10°C per min, and were examined when cool. The surfaces of specimens prepared from Molybdenum A were consis- tently clean and featureless, except for thermally etched grain boundaries, see Fig, l(a). On the other hand, Molybdenum B had surfaces containing many needle- and featherlike markings, see Fig. l(b). These features were present in all surface grains, and within a given grain belonged to families

Jan 1, 1965

By E. T. Cox

The Albion phosphate-district embraces a territory about 4 miles wide and 6 miles long, in a northerly and southerly direction, situated in Levy county, Florida. The Florida Central and Peninsular railroad, running from Fernandina, a shipping port on the Atlantic, to Cedar Keys, on the Gulf of Mexico, passes through the center of the district. The post-office and railroad station is in the town of Albion. The physical features of the district present a series of white aqd whitish-gray sand-hills and ridges, rising about 130 feet above tide-water. The sand lies in a loose body, like that seen on the ocean beaches. In places the hills have the appearance of sand-dunes, such as are seen along the Platte river, in Nebraska. Beneath the sand are found the phosphate-deposits, which are partially exposed in places, but, for the most part, lie buried to a depth of 15 feet and more. In this district the phosphate is designated as " hard rock,"

Jan 1, 1896

By Moshe Sheinkin, Douglas E. Julin

Large tonnage operations face many problems in adequately planning ahead for future years production. In order to maintain desired levels of production, such problems as source of tonnage, man- power and equipment requirements, tailings disposal and water requirements must be anticipated. Of course, before any of these problems can be analyzed, daily tonnage requirements and its source must be determined. Looking ahead for one year or even two or three is usually not sufficient time to adequately prepare an area for production. Because of the sequence of mining and the multilevel nature of the 42,000 tpd Climax mine in Colorado long-range planning must be on a ten-year basis. By using a ten-year base, adequate time is allowed to gain access and prepare a new level for production. Usually eight years will be required for this phase of the initial mine preparation. Once production has been started on a level and access to the area is available, three years is usually sufficient to prepare a new block for production as long as it follows in the normal sequence of mining.

Jan 4, 1967

The following specifications, proposed by a sub-committee of the American Society for Testing Materials, are still to be adopted and subsequently submitted to the International Association for Testing Materials. Standard Specifications for Pig-Iron and Castings. I. Analysis.—It is recommended that all purchases be made by analysis. II. Sampling.—In contracts where pig-iron is sold by chemical analysis, each carload, or its equivalent, shall be considered as a unit. At least one pig shall be selected at random from each two tons of every carload, and so as to fairly represent it. Drillings shall be taken so as to fairly represent the fracture surface of each pig, and the sample analyzed shall consist of an equal quantity of drillings from each pig, well mixed and ground before analysis. III. Allowances and Penalties.—III all contracts, in the absence of a definite understanding to the contrary, a variation of 10 per cent. of silicon, either way, and of .01 in sulphur above the standard is allowed. A deficiency of over 10 per cent. in the silicon, up to 20 per cent., and a further increase in sulphur up to .01 over the above allowance subjects the shipment to a penalty of 1 per cent. in the price for each element so affected. IV. Base Analysis OF Grades. —In the absence of specifications the following numbers, known to the trade, shall represent the appended analyses for standard grades of foundry pig-iron, irrespective of the fracture, and subject to allowances and penalties as above. Silicon Sulphur Grade. Per Cent. Per Cent. No. 1,...2.75 0.035 No. 2,.2.25 0.045 No. 3,........1.75 0.055 No. 4,.1.25 0.066 Cast-Iron Pipe and Special Castings. I. Description of Pipes.—The pipes shall be made with hub- and spigot-joints, and shall accurately conform to the dimensions given in Tables Nos. I. and 11. They shall be straight and shall be true circles in section, with their inner and outer surfaces concentric, and shall be of the specified dimeneions in outside diameter. They shall be at least 12 feet in length, exclusive of socket. For pipes of each size from 4-inch to 24-inch, inclusive, there shall be two standards of outside diameter, and for pipes from 30-inch to 60-inch, inclusive, there shall be four standards of outside diameter, as shown by Table No. 11.

Jan 1, 1905

By A. Wadood M. A. El Rabaa, William A. Hustrulid, William F. Ubbes

The spatial distribution of the deformation modulii around the CSM/ONWI test facility was determined using an NX version of the CSM cell. Approximately 840 modulus measurements were made in six rings (each ring containing seven holes each 6 m in length) of boreholes. These parallel rings were spaced at 2.4 m intervals along the room. Contour plots of the modulii revealed that the depth of the blast damage zone varied both with perimeter position and distance away from the opening. The maximum depth of disturbance appeared to be of the order of 60 cm. At locations removed from the opening, the variability in modulus was quite high reflecting the presence of joints, faults, shear zones and foliation. A comparison of rock mass modulii (ER) with those obtained from the laboratory testing of core (E), revealed that ER [=] 0.5 E.

Jan 1, 1982

Sec. 1. The membership of the Institute shall comprise six classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members. All shall be equally entitled to the privileges of membership, excepting that no member of any class whom residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the claw of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members.

Jan 1, 1936

NEW MEMBERS The following list comprises the, names of those persons who became members during the period June 10 to July 10, 1914: Members ALDRICH, HAROLD W., Supt. of Leaching Plant, Washoe Red. Wks., Anaconda Copper Co., Anaconda, Mont. AYER, FRANK ASHTON, Mine Foreman.. ..Detroit Copper Co., Morenci, Ariz. BELL, ARTHUR F. L., Chief Engr., Associated Oil Co.., 817 Sharon Bldg., San Francisco, Cal. BERGMAN, JULIUS GUSTAF, Mech. Engr., Chief Draftsman, Arizona Copper Co. Morenci, Ariz. BURT, CURTIS F., Min. Engr., Pittsburg-Dolores Mining Co., Rockland, via Yerington, Nev. CALLAWAY SCOTT DAVID, Chem La Harpe Smelter Co., La Harpe, Kan. CAMPBELL, W. C., Min. Engr 4 Princess St., Roodeport, Transvaal, So. Af. CARROLL, GEORGE A., Genl. Mgr Kildare Min. Co., Manson, B. C., Canada. CARUTHERS, JOHN LYTLE, Min. Engr., Asst. Engr., St. Louis, Rocky Mountain & Pacific Co.. Raton. N. M.

Jan 8, 1914

By L. R. Velho, N. A. D. Parlee, J. Gani

THE unsteady-state type of gas-liquid metal diffusion cell1 has found considerable application.2"4 Cells of this general design can function as steady-state cells if allowed to operate long enough to reach steady state. This report tells of some success in the adaption of this type of cell for steady-state work, using the 0-Ag system in which the mass transfer of the gas "species" is basically controlled by diffusion in the liquid. The gas, e.g-., O2, is maintained in the cell tube'-3 at 1 atm pressure, Fig. 1, by buret and sensitive oil manometer. The gas, after diffusing through the stagnant metal, escapes at the annular metal surface around the tube at a lower constant partial pressure, in this case that of O2 in slowly flowing air, 1 atm.

Jan 1, 1970

[based on o report by HUBERT E. RISSER] There is a tendency among laymen to relegate America's coal industry to Pennsylvania and West Virginia, completely overlooking-or unaware of- the vast reserves, both those developed and those untapped, situated in the 1.4 million square miles between the Appalachians and the Rockies. At the 1965 AIME Annual Meeting, Hubert E. Risser, Principal Mineral Economist of the Illinois State Geological Survey, presented an interesting picture of the wealth of mineral fuels occurring in that area. In his talk entitled "Trends in Mineral Fuels in the Central United States", Mr. Risser underscored the fact that "more than half of the nation's known reserves of each of the three major fuels-oil, gas and coal-lie within the Central area." The highlights of his speech, with emphasis on the coal situation, are excerpted below.

Jan 6, 1965

A LARGE proportion of the steel that is melted and refined in the United States and poured into ingots is made in basic open- hearth furnaces. The capacity of these furnaces varies over a wide range with a large majority falling within limits of 50 to 200 tons (Fig. 1) The two general types of furnace design used are stationary [ ] and tilting furnaces, the former being much more common. The fuel burned in such furnaces is either one of several types of gas, or a liquid fuel such as oil or tar, or a combination of gas and liquid fuel. GENERAL FEATURES OF FURNACE CONSTRUCTION The design of a modern stationary furnace built to burn liquid fuel and with a capacity of 175 tons is shown in Figs. 2 to 4. The cross- section of the furnace at the tap hole is illustrated in Fig. 2, which shows the bottom construction, sloping back wall, and the rigid steel

Jan 1, 1944

By I. E. Rosenzweig

THE problem considered in this paper is as follows: An arbitrary horizontally stratified area is given. The electrical properties of this area are characterized by a function p(z) (Fig. 1), which shows the relationship between resistivity p of thes oil and the depth z. For such general case the apparent resistivity p* will be computed, by FIG. 1.-GRAPH OF FUNCTION p(z) FIG. 2.-GRAPH OF p(Z) FOR n HOMO-GENEOUS LAYERS. earth-resistivity measurements carried out by any given configuration of electrodes. General solutions of this problem appear to be very important for interpretation of field results of resistivity measurements, concerning structural investigations. Such solutions have been given by many authors for the special case of a finite number of homogeneous layers (Fig. 2)1-4 as well as for the more general case of continuously rang-ing resistivities. 5-8

Jan 1, 1939