Search Documents

By C. A. O’Connell

Surface exploration drilling at Mufulira started in 1928, with drillhole No. 1 intersecting ore near the eastern fringe of the deposit. Subsequent drilling along strike intersected ore until the western fringe was fixed some 7500 ft west of drillhole No. 1. Further intensive drilling down dip disclosed a large triangle of ore with its apex 3350 ft deep. It contained approximately 11 6 million tons of ore at 4.41% total copper in three superimposed orebodies. The east and west limits of the orebodies were presumed to have a pronounced rake to the north with a strike length of 8000 ft. Subsequent exploration underground seemed to bear out this presumption to the 1150 ft level. In 1947, attention was directed to the area west of the known orebodies in conjunction with plans for increased production and increased depth of the mine workings.

Jan 12, 1962

By R. F. Mehl, R. W. Parcel

THE rate of the decomposition of austenite in eutectoid steels, forming only pearlite, may be expressed fundamentally in terms of the rate of nucleation and the rate of growth of pearlite nodules. This matter has received much attention in recent years. (The basic references are listed in ref. 1; references of particular import to the present work will be given separately.) Systematic data have been developed for plain carbon eutectoid steels.:! Although the physical factors affecting the rate of nucleation, N, in case of plain carbon steels have presumably been identified, they cannot as yet be evaluated quantitatively.' Several somewhat successful attempts, however, have been made to calculate the rate of growth, G. In the latter case the important factors determining the edgewise growth of pearlite have been assumed to be: 1—the interlamellar spacing; 2—the concentration extremes and concentration contours of carbon in austenite in front of the growing pearlite interface; and 3—the rate of diffusion of carbon in austenite.* The only systematic data on N and G for pearlite in alloy eutectoid steels are those for Co-steels;6 there are no data on alloy eutectoid steels in which the alloying element is known to decrease the rate of formation of pearlite, apart from a few scattering data reported earlier' for steels containing manganese. This paper reports a systematic study of N and G for eutectoid alloy steels containing molybdenum and nickel, respectively. In order to provide information of help in understanding the results, new data are presented on the effect of molybdenum on the interlamellar spacing of pearlite, So; data on the effect of nickel on So have already been published.' The alloys used were in five groups: 1—Pure Fe-C-Mo alloys (Table I) were supplied by the Climax Molybdenum Company of Michigan, Detroit. They were made from Armco ingot iron of standard analysis, Acheson graphite, and ferro-molybdenum, melted in silica-lined crucibles in a high frequency induction furnace. The ferromolyb-denum was added to the melted steel, followed in 5 min by 0.08 pct Al. The ingot as-cast measured 23/4x 31/4x10 in.; it was hot-forged at 1150°C to a bar 1 in. sq.

Jan 1, 1953

By Gerhard Derge

THE introductory paper1 of this series described the potential behavior of tin in sodium carbonate and bicarbonate solutions whose pH ranged from 8.4 to 11.2 and demonstrated that significant and reproducible results could be obtained by proper attention to experimental technique. In examining the corrosion of tin under such conditions, it is desirable to know the effects of anions, aside from carbonate, that are likely to be present in commercial materials packaged in tin. Therefore, in this paper the potential behavior of tin in carbonate solutions to which sodium fluoride, chloride, bromide, iodide, sulphate, nitrate, monobasic phos-phate, dichromate, perborate and acetate have been added will be described. For most of the additions, solutions containing 0.001 and 0.01 .moles of the added material were studied. The experimental procedure was exactly the same as that described in the first paper; the pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicar-bonate as follows: pH 0.1 M NaHCO3 8.4 2 parts 0.1 M NaHCO3, 1 part 0.1 M Na2CO3 9.5 1 part 0.1 M NaHCO3, 2 parts 0.1 M Na2CO3 10.0 0.1 M Na2CO3 11.2 The reagents used were all of C.P. grade. The anions studied may be divided into three groups: (1) anions that had little or no effect upon the potential curves-sulphate, nitrate, and acetate; (2) those that helped to prevent corrosion at low pH only-fluoride, chloride, bromide, and iodide; (3) those that helped to prevent corrosion at high pH also-phosphate, perborate, and chromate.

Jan 1, 1939

By Michael B. Kahle, Fred J. Scheaffer

Production scheduling, along with production planning, provides projections of future mining progress and time requirements for the development and extraction of a resource. These schedules and plans are used by management as a means of attaining the following objectives (1) maintaining or maximizing expected profit, (2) determining future investment in mining, (3) optimizing return on investment, (4) evaluating alternative Investments, and (5) conserving and developing owned resources. The first four goals are generally concerned with mining costs, both capital and operating requirements, and as such, play an important role in production planning. However, this chapter is concerned with the fifth management objective of resource development in order to conserve and perpetuate the corporate entity. The following discussion is based on the premise that detailed economic evaluations and market surveys have been performed and analyzed and that the results indi¬cate a viable project.

Jan 1, 1979

By R. M. Brick, M. A. Williamson

Certain features of the response of copper and brass to deformation and recrystallization remain obscure. The textures obtained on rolled sheet are listed by Schmid and Boas1 as: No adequate explanation has been advanced for the presence of the secondary deformation texture of copper and its absence in brass or for the origin of the cubic recrystallization texture of copper.2 A recent publication3 attempted to rationalize the above empirically described annealing texture of brass on the basis of retention of the (110) [112] rolling orientation plus twinning about the central octahedral poles of the usual secondary (110) [115] orientation. The difierence in the textures of annealed copper as compared to 70-30 brass is also shown by the difference in the position of ears for drawn copper, at o° and go", as compared with drawn brasses, at 45o, for all compositions between oo-10 and 70-30.4 Data on indi- vidual crystals are as yet too few to permit of an analysis of these textures comparable to that of mild steel as made by Barrett and Levenson.5 Experimental Methods The materials studied included copper specimens cut from the central, equiaxed crystal portion of a tough-pitch wirebar; brass made from this copper and high-purity (99.99 per cent) zinc including alloys of 7 per cent, 15 per cent, 24 per cent, 29 per cent and 36 per cent Zn and large single crystals of 70-30 bras. Sections 1/4 in. thick of the cast polycrystalline copper and brasses were reduced 40 per cent by rolling, recrystallized to a common grain size of 0.045 mm. and then rolled directly to foil 0.002 in. thick. Hardness readings employing both the Vickers and Rockwell machines were taken at intervals during the reduction. For comparison, similar specimens were cross-rolled—i.e., turned through 90° for each pass—and comparable hardness data were secured. Finally sections from the single crystals of brass were cut to obtain the following initial orientations; these sections were rolled, hardness data secured and a complete micrographic record of structural changes obtained.

Jan 1, 1941

By R. M. Brick, M. A. Williamson

Certain features of the response of copper and brass to deformation and recrystallization remain obscure. The textures obtained on rolled sheet are listed by Schmid and Boas1 as: No adequate explanation has been advanced for the presence of the secondary deformation texture of copper and its absence in brass or for the origin of the cubic recrystallization texture of copper.2 A recent publication3 attempted to rationalize the above empirically described annealing texture of brass on the basis of retention of the (110) [112] rolling orientation plus twinning about the central octahedral poles of the usual secondary (110) [115] orientation. The difierence in the textures of annealed copper as compared to 70-30 brass is also shown by the difference in the position of ears for drawn copper, at o° and go", as compared with drawn brasses, at 45o, for all compositions between oo-10 and 70-30.4 Data on indi- vidual crystals are as yet too few to permit of an analysis of these textures comparable to that of mild steel as made by Barrett and Levenson.5 Experimental Methods The materials studied included copper specimens cut from the central, equiaxed crystal portion of a tough-pitch wirebar; brass made from this copper and high-purity (99.99 per cent) zinc including alloys of 7 per cent, 15 per cent, 24 per cent, 29 per cent and 36 per cent Zn and large single crystals of 70-30 bras. Sections 1/4 in. thick of the cast polycrystalline copper and brasses were reduced 40 per cent by rolling, recrystallized to a common grain size of 0.045 mm. and then rolled directly to foil 0.002 in. thick. Hardness readings employing both the Vickers and Rockwell machines were taken at intervals during the reduction. For comparison, similar specimens were cross-rolled—i.e., turned through 90° for each pass—and comparable hardness data were secured. Finally sections from the single crystals of brass were cut to obtain the following initial orientations; these sections were rolled, hardness data secured and a complete micrographic record of structural changes obtained.

Jan 1, 1941

By P. G. Shewmon, F. N. Rhines

THE determination of the self-diffusion coefficient of magnesium has been made possible recently by discovery1-1 of a radioactive isotope, Mg28 having a half-life of 21.3 hr,1 and subject to manufacture in useful quantity. In the present research this material was condensed from the vapor phase upon a surface of high purity magnesium. The progress of diffusion of the tracer atoms into polycrystalline magnesium was followed by machining layers and measuring the change in the intensity of radiation as a function of the distance of each layer from the surface. The self-diffusion coefficient was found to be 2.1 X 10-8 sq cm per sec at 627°C, 3.6 X 10-9 sq cm per sec at 551°C, and 4.4 X 10-10sq cm per sec at 468°C; the activation energy is about 32,000 cal per mol. Experimental Procedure Since there was no other published measurement of a diffusion velocity in any magnesium-base material, is was necessary to employ a number of new experimental techniques. The short half-life of Mg28 made it necessary to complete the entire experimental procedure within three or four days. This meant that the work had to be done where a cyclotron was readily accessible and that all operations, prior to the diffusion heat treatment, had to be so designed as to minimize their time requirements. Unusual problems were imposed also by the chemical reactivity of magnesium, its high vapor pressure, and the fact that no satisfactory method for elec-trodepositing magnesium on magnesium is presently available. Finally, the machining and handling of the easily air-borne radioactive-magnesium chips involved certain health hazards, resulting in the need for further experimental restrictions. Preparation of Mg28 The Mg28 was produced in the Carnegie Institute of Technology syncrocyclotron by the neutron spallation of chlorine.5 his involved bombarding a 2 gram crystal of high purity NaCl with a beam of 350 mev protons for a period of 2 hr, after which the crystal was dissolved in warm water and the Mg28 was concentrated and purified by chemical means (see Appendix). About 50 microcuries of Mg28 thus were obtained in the form of magnesium oxinate (8 hydroxyquin-olatc?), which was ignited in air to produce MgO. This in turn was reduced to magnesium metal vapor, by the method of Russell, Taylor, and Cooper," in the vacuum apparatus shown schematically in Fig. 1. Here the essential part is a tantalum ribbon, slightly dished to receive the MgO. The ribbon, pre- viously outgassed at high temperature, is heated to about 1700°C by passing an electric current through it, whereupon tantalum oxide is formed, magnesium vapor is released almost instantaneously, and condensed partly upon the diffusion sample. Diffusion-Sample Preparation: Hot-extruded magnesium rod, 21/32 in. round was used in making the diffusion specimens. The magnesium analyzed as follows: 0.004 pct Al, 0.027 pct Fe, 0.040 pct Mn, 0.0004 pct Cu, 0.0002 pct Ni, and less than 0.01 pct Ca, 0.0004 pct Pb, 0.0011 pct Si, 0.001 pct Sn, and 0.001 pct Zn. A brief study of the crystal texture of this material revealed a sharp fiber texture with the (001) plane roughly parallel to the extrusion axis. Cylindrical samples 1/2 in. long by 5/8 in. were machined from this rod, the end faces dressed on 3/0 emery, and lightly etched with 20 pct HC1 in water. These samples then were annealed for at least twice the intended time of diffusion, at the intended diffusion temperature, in order to stabilize the grain structure at about 1 mm average diameter. The annealing treatments were conducted in argon in the same apparatus and in the same manner as the subsequent diffusion treatments, which will be described presently. Thus, a strain-free plane surface was produced, but there remained a layer of MgO which had largely to be removed before the layer of Mg28 was deposited. Most of this layer was taken off by two light passes over 3/0 emery paper. The balance of the oxide and a thin layer of metal were then removed by etching 5 to 10 min in 4 pct nital (4 pct HNO3 and 96 pct ethyl alcohol) made with absolute alcohol. There followed immediately three quick rinses in: 1-49 1/2 pct methanol, 49 1/2 pct acetone, and 1 pct formic acid, 2-50 pct methanol and 50 pct acetone, and 3-pure benzene. This procedure is essentially that of Sturkey.7 The resulting surface, which was of almost elec-tropolished brightness, remained plane and was free of cold work. It could be kept clean by storing under benzene, or in a desiccator; short exposure

Jan 1, 1955

By Carl J. McHargue

Mechanical twins were produced in electron-beam melted columbium by high-speed impact at room temperature and by slow or fast compression at -196°C. The composition plane of the twins was { 112} and the shear direction was <111>. Notches in the twin bands often corresponded to traces of {110) of the matrix and appeared to be untwinned regions. Markings within the twin bands were interpreted as resulting from {110} slip in the twins. THERE has been much work in recent years concerning plastic deformation by glide, and the dislocation theory relating to glide has reached a relatively high degree of development. On the other hand, there have been fewer studies of deformation by mechanical twinning, and understanding of this process is far from satisfactory. This method of deformation is of interest for at least two reasons. First, it provides a mechanism in addition to glide for the relief of stresses, and, in the bcc and hexagonal close-packed metals may result in significant amounts of plastic flow. Secondly, there is the possibility that twins may act as barriers for dislocation movement, resulting in pile-ups which could nucleate cracks. As might be expected, the bulk of the literature on mechanical twinning in the bcc metals is concerned with iron. A good summary of the work done prior to 1954 is contained in the book by all.&apos; Recently the refractory bcc metals have become increasingly important. Limited studies have shown that tantalum,2,3 molybdenum,4,5 vanadium,6,7 tungsten,&apos; and columbium9-11 deform by mechanical twinning under some conditions. Alloys of molybdenum with rhenium and tungsten with rhenium show extensive deformation by twinning at room temperature.I2-l4 Most of these studies have dealt primarily with mechanical properties at low temperatures or have shown the existence of twins, and there is only a small amount of information concerning the conditions under which they form. The subject of the present paper is the formation of twins under stress in columbium with a consideration of their morphology. EXPERIMENTAL PROCEDURE The material used for these studies was taken from an ingot of columbium which had been melted twice by the electron-be am-method. The analysis of the ingot was (in ppm): B < 1, C = 10, Fe < 100, The cast ingot contained very large grains, and it was possible to obtain single-crystal prisms which measured from ¼ to 3/4 in. on a side. A few experiments were conducted on polycrystalline plate which was prepared by rolling material from the same ingot at room temperature and annealing at 1000 in a dynamic vacuum of 10-6 mm Hg. This gave a plate in which the grains had an average diameter of 3 mm. After the specimens were cut from the ingot, the six faces were metallographically polished and elec-tropolished to remove all traces of cold work. Most of the observations were made on the surfaces of the deformed specirllens without further treatment. Occasionally, etching after deformation was desirable. In these cases, an etchant of the composition 50 parts H2O, 5 parts HNO3 25 parts HF, and 10 parts H2SO4 was found to delineate the twins very well. Unless considerable care was taken to ensure the removal of all disturbed metal left by the mechanical polishing, etching failed to reveal many of the features discussed in this; paper. The specimen&apos;s were deformed either by impact or slow compression at 77°K (liquid-nitrogen coolant), 198°K (dry ice and acetone coolant), and 298°K. The impact load was delivered by a hammer except in one case where the load was delivered by a bullet. Slow compression was carried out on a hydraulic testing machine equipped with a chamber to hold the coolant. EXPERIMENTAL RESULTS It has been generally believed that the conditions favoring the formation of deformation twins are large grains, low temperature, and impact loading. In fact, Barrett and Bakish2 found twins in tantalum only after impact deformation at 77°K, and Adams, Roberts, and Smallman10 observed twins in columbium only at 20 For these reasons, the initial experiments of this study used impact loading. Hammer blows caused many bands resembling twins in single crystals a.t 77" but not at 198°K. Only a few slip lines were observed on any of the single-crystal specimens of this study—essentially all the deformation occurred by twinning. The appearance of the twins on the as-deformed surface is shown in Fig. 1. Although both Figs. 1(a) and l(b) are photomicrographs of twins taken at the same magnification and from the same crystal, they are startlingly different in appearance. Fig. 1(a) was taken from the crystal face approximately perpendicular to the shear direction, whereas Fig. 1(b) was taken from

Jan 1, 1962

By H. A. Guess

AT the outset, said Mr. Guess, I may say that although I believe the present engineering courses in the various colleges and universities could be arranged to give the student within the same time limit a broader general education of un- doubted value, still I do not agree with the view held by many that engineers in comparison with those of other occupations-let us say doctors, lawyers, bankers, and so-called business men-seldom arrive at high executive positions. After all, we must remember that engineers are not very numerous as compared with the occupations just mentioned and therefore a lesser number reaching high executive positions stated numerically might be a larger number stated as a percentage. We all know there must be throughout the United States say three doctors to one engineer, but I don&apos;t think that even numerically there are as many doctors in high executive positions as engineers, and it is a fortunate thing for the country that doctors as a class are so busily engaged in alleviating sickness and suffering and in the advancement of medical science that they do not aim particularly for high executive positions.

Jan 1, 1926

US 4,192,851-Recovery of elemental sulfur and the metal values from a complex sulfide ore containing two or more of the metals zinc, lead, copper, silver, gold and/or other metals. A mixture of ore and sulfuric acid and/or spent electrolyte is flowed at optimum temperature and pressure in a quiescent zone to dissolve selected metals and sulfur and coalesce the sulfur. The coalesced sulfur and unreacted sulfides are separated by flowing the leach slurry with an upward velocity component The separated materials are discharged and further processed by conventional methods as war- ranted. H.E. Hirsch, J F. Higginson, EG. Parker, and G M Swinkels, assigned to Sherritt Gordon Mines Ltd. Mar. 11, 1980. 6 pp. (423-28) Filed. 3-14-78 (886,368). Priority. United Kingdom, 3-15-77 (10800/77).

Jan 1, 1982

By W. F. Burns

(Butte Meeting, August, 1913.) ATTEMPTS were made in 1908, at the Great Falls Works, to produce ingots direct from the Butte precipitate by smelting the material in a reverberatory refining furnace. The ingots produced in this manner averaged 99.4 per cent. of copper and 0.40 per cent. of arsenic and antimony. The copper content being considered too low, it. was decided to cast the copper into anodes and to treat the anodes in the electrolytic plant. No. 1 Furnace, in which the precipitate was treated, was a regular cathode refining furnace previously employed in making wire bar, cake, and ingot from electrolytic cathodes. The hearth of the furnace was 24 by 12 ft., having a capacity of 100,000 lb. of cathodes. The furnace was coal fired, and the copper was dipped by means of trolley ladles.

Jan 7, 1913

By H. R. Wheeler

CREATION of a "committee on promotion of student interest in coal mining" has an encouraging implication for the coal industry. It is indicative that mining men, both in the field and in the educational centers, realize that the problems of the industry require the best talent available. Young men are being invited into coal on the premise that it needs them, that it offers opportunity for creative work and the realization of their objectives. In initiating a movement which purports to meet the objectives of any young man who spends four or five years of his life in college, the industry does so with a full realization of its obligations.

Jan 1, 1940

By Charles H. Fulton

CHARLES H. FULTON, chairman, presided at the first session of the Mineral Industry Education Division on Wednesday morning. Reporting for the program committee, Edward Steidle, its chairman, pointed out that its function was not to arrange programs for meetings but to plan a program for the Division to follow in the development of its activities. This was appropriately followed by presentation and discussion of his paper, "Basic Trends in Mineral Industries Education," which, being available in printed form, was only presented in oral abstract. Jay A. Carpenter submitted interesting written discussion that was read, in his absence, by A. M. Smith. Most of the morning was devoted to the discussion of the paper, which was too extensive and ranged too widely to attempt to report in much detail. H. T. Mann, H. P. Hammond, Cadwallader Evans, C. H. Fulton, T. T. Read, D. F. McFarland and P. B. Bucky joined in the discussion, Mr. Hammond making a plea for more unification in mineral industry education, saying that in the study he made for the Society for Promotion of Engineering Education about 35 different curricula preparatory to work in the mineral industry were discovered to exist. He felt that most of the needs of the mining industry could he met by men who had had four years of engineering training of good enough basic quality to permit them to advance along special lines. However, there was apparently a growing demand, as reflected by the increasing number of candidates for the Master&apos;s degree in engineering, for men with more thorough training in the fundamentals.

Jan 1, 1933

G. D. Kneip, Jr., and J. 0. Betterton, Jr. (Union Carbide & Carbon Corp., Oak Ridge, Tenn.)—The authors have contributed to the theory of zone melting by considering the effects of the solidification of the final zone on the distribution curves for the finite length bar. However, they do not consider in sufficient detail the restrictions imposed by the particular metals involved. Eq. 4 has the analytical solution which is equivalent to Pfann&apos;s&apos; equation for normal solidification of the final zone. For distribution coefficients less than one, it is apparent from this form of the equation that, as the solidification approaches completion, the concentration attains extremely large values which are inconsistent with the density of physical materials. The necessary restrictions then are that the solute concentration cannot exceed the density of the alloy, or more frequently, the solubility limit in the solid phase. Secondly, the distribution coefficient cannot be constant from 0 to 100 pet solute unless the liquidus and solidus coincide over this whole region. It would thus be more correct to impose limits on the solubility such as would be indicated by a typical eutectic diagram. Furthermore, in this case the assumption that the distribution coefficient remains constant is more likely to be realized. Eq. 4 should then be replaced by the following C,,(x) =k/L-x [ ?11 3 C11 (x)Ddx - ?11 4 Cn(x)dx= k[Cn (L-l)/k] [ L-x/l]x-1 L-l = x = L-l [kCenterlie/Cn (L-l)]1/k-1 The typical shape for the distribution curve in the final zone is indicated schematically in Fig. 12 for the simple eutectic case. The solidification proceeds according to Pfann&apos;s&apos; expression until the concentration reaches the maximum solubility in the solid phasc. At this point, the concentration changes abruptly to the eutectic composition and remains at this value for the duration of the solidification. The width of the flat region, and the back reflection of this effect into the concentration curve on subsequent passes, depends upon the ratio of the eutectic concentration to the original concentration, upon the distribution coefficient, and upon the number of passes. Similar effects on the concentration curves in the first zone length would be expected in many systems for which the distribution coefficient is greater than one, and where the maximum solubility is not too much larger than the original concentration. The discussers agree with the authors that the assumption that the liquid is uniform in concentration should be considered with caution. Kneip and Better-ton&apos; have shown, however, that in floating zone refining of zirconium, using induction heating, the distribution of iron agrees with theory which assumes a uniform liquid composition. Hence, in this case, the experimentally realized distribution coefficient agrees with the present phase diagram within the experimental uncertainty. L. Burris, Jr., C. H. Stockman, and I. G. Dillon (authors&apos; reply)—The authors are happy to have received the comments of G. D. Kneip, Jr., and J. 0. Betterton, Jr., which provide additional insight into the zone refining process. It is true that the equations developed are inapplicable if the solute solubility in the solid phase is exceeded. However, this restriction on the use of the equations was clearly stated in the paper. A closer approach to

Jan 1, 1957

By Harry H. Power

WORK of the Committee on Education of the Petroleum Division has been under way for approximately-one year. Although some progress has been made, further activities of the Committee are necessary in order to discuss mutual problems more thoroughly by a unified group interested primarily in this field of specialization.

Jan 1, 1944

1. Healthy and active Local Section organizations are vital factors in promoting the vigor and growth of the Institute. 2. Activity on the part of Local Sections should be recognized and stimulated by appropriation of funds from the Institute&apos;s treasury; and these appropriations should be as large as is consistent with the relative needs for other activities. 3. As between different Sections, the amount of such appropriations should be based primarily on the extent of activities as reflected in the number and character of meetings held and the attendance of the members at such meetings. 4. In making a request for funds for any year, the officers of a Local Section should submit a report on the printed form approved by the Directors at their meeting on November 19, 1937. 5. A standing Committee on Local See-

Jan 1, 1943

By D. B. McDyre

THE object of this study was to compare variations in slag volumes with tap changes while maintaining all other factors constant. This meant: 1. Same type of heat (Spec. SAE 1030). 2. Same charging material (3500 lb foundry, 4000 lb bought scrap). 3. Same amount of sand by weight to fix slag line. 4. Same method of melting with the exception of tap changes. 5. Same method of weighing slag after each test. The equipment of the Dodge Steel Co. consists of a 132-ton Heroult furnace lined with silica brick, using three 8-in. electrodes and a 2000-kva transformer, with four tap changes. In the melting practice we use a Fischer Carbanalyzer and a Herty viscosimeter and try to standardize all heats by making necessary carbon and slag adjustment before boil to keep all heats as uniform as possible.

Jan 1, 1947

1. Healthy and active Local Section organizations are vital factors in promoting the vigor and growth of the Institute. 2. Activity on the part of Local Sections should be recognized and stimulated by appropriation of funds from the Insti¬tute&apos;s treasury; and these appropriations should be as large as is consistent with the relative needs for other activities. 3. As between different Sections, the amount of such appropriations should be based primarily on the extent of activities as reflected in the number and character of meetings held and the attendance of the members at such meetings. 4. In making a request for funds for any year, the officers of a Local Section should submit a report on the printed form approved by the Directors at their meeting on November 19, 1937. 5. A standing Committee on Local See-

Jan 1, 1942

1. Healthy and active Local Section or¬ganizations are vital factors in promoting the vigor and growth of the Institute. 2. Activity on the part of Local Sections should be recognized and stimulated by appropriation of funds from the Insti¬tute&apos;s treasury; and these appropriations should be as large as is consistent with the relative needs for other activities. 3. As between different Sections, the amount of such appropriations should be based primarily on the extent of activities as reflected in the number and character of meetings held and the attendance of the members at such meetings. 4. In making a request for funds for any year, the officers of a Local Section should submit a report on the printed form approved by the Directors at their meeting on November 19, 1937. 5. A standing Committee on Local Sec-

Jan 1, 1944

By AIME AIME

TWO papers, "Calcium, Strontium, and Barium Metals," by Charles Hardy and Paul M. Tyler, and "The Mining of Gems and Ornamental Stones by American Indians," by Sydney H. Ball, were presented before the Rare Minerals and Metals group at its session Tuesday afternoon in the Auditorium. Donald M. Liddell, chairman, presided. Mr. Tyler summarized the first paper, outlining the uses, history, occurrence, manufacture, production and trade, markets and prices of the three metals. In discussion, in response to the chairman&apos;s query on "what are they doing in Russia with calcium, strontium, and barium," Guy C. Riddell replied that nothing is being done on a production basis. The great rare metals plant in Moscow is active, however, on other elements. "They are making radium chloride, uranium oxide, vanadium, cadmium, tungsten, molybdenum, selenium, antimony compounds; and mercury, nickel and arsenic are under production at interior plants. The rare metals plant is busily conducting research on beryllium, rhenium, lithium, bismuth, strontium and zirconium. These are the main rare metal activities. Much hard-alloy work. for cutting and facing, is under way:

Jan 1, 1933