Search Documents

By Henry M. Howe, Joseph Winlock, Francis B. Foley

This investigation was undertaken for the purpose of determining, in a systematic way, the effect of the rate of cooling of steels, heated to above the transformation range, on their various mechanical properties. This paper gives the results obtained in the investigation of the heat treatment of carbon steels carried out under the auspices of the Committee on The Heat Treatment of Carbon Steels of the Engineering Division, National Research Council. The objects of this committee, of which Dr. Henry M. Howe was chairman, were to increase knowledge of the influence of heat treatment on the mechanical properties of carbon steel. The mcthod pursued was to subject specimens of steel of the carbon contents most used for engineering work, 0.34 per cent., 0.52 per cent., and 0.75 per cent., to various heat treatments, and to test the mechanical properties thus induced. The steels were the same as were used by the committee on fatigue phenomena. This project was financed jointly by the U. S. Bureaus of Mines and Standards; industries and university laboratories have cooperated. A large part of the work was done at Doctor Howe's private laboratory. The committee consisted of F. B. Foley, H. AT. Boylston, H. C. Boynton, G. K. Burgess, H. J. French, J. H. Hall, Zay Jeffries, R. S. Johnston, F. C. Langenberg, H. F. Moore, E. H. Yeirce, H. S. Rawdon, W. E. Ruder and 11. J. Stagg. The work was undertaken at the suggestion of Doctor Howe, who thought, at the outset, that steel in the sorbitic state might have properties which, for most engineering purposes, would be better than those of the usual or pearlitic state. By a systematic variation in the heating

Jan 1, 1923

By Joseph Winlock, Francis B. Foley, Henry M. Howe

This investigation was undertaken for the purpose of determining, in a systematic way, the effect of the rate of cooling of steels, heated to above the transformation range, on their various mechanical properties. This paper gives the results obtained in the investigation of the heat treatment of carbon steels carried out under the auspices of the Committee on The Heat Treatment of Carbon Steels of the Engineering Division, National Research Council. The objects of this committee, of which Dr. Henry M. Howe was chairman, were to increase knowledge of the influence of heat treatment on the mechanical properties of carbon steel. The mcthod pursued was to subject specimens of steel of the carbon contents most used for engineering work, 0.34 per cent., 0.52 per cent., and 0.75 per cent., to various heat treatments, and to test the mechanical properties thus induced. The steels were the same as were used by the committee on fatigue phenomena. This project was financed jointly by the U. S. Bureaus of Mines and Standards; industries and university laboratories have cooperated. A large part of the work was done at Doctor Howe's private laboratory. The committee consisted of F. B. Foley, H. AT. Boylston, H. C. Boynton, G. K. Burgess, H. J. French, J. H. Hall, Zay Jeffries, R. S. Johnston, F. C. Langenberg, H. F. Moore, E. H. Yeirce, H. S. Rawdon, W. E. Ruder and 11. J. Stagg. The work was undertaken at the suggestion of Doctor Howe, who thought, at the outset, that steel in the sorbitic state might have properties which, for most engineering purposes, would be better than those of the usual or pearlitic state. By a systematic variation in the heating

Jan 1, 1923

By Max Kraut

UNTIL VERY RECENTLY the flotation process has not found much application in the treatment of gold ores. No appreciable improvement has been made lately in the technology of this application; but the possibilities of flotation have been more fully appreciated. Excellent results were obtained long ago, but few operators paid much attention to them. For instance, in 1915 extensive experiments were carried out by Mr. Beauchamp and Minerals Separation on ores from the Dutch-Sweeney mine near Jimtown, Calif. The ore contained gold-bearing pyrite and laboratory tests indicated a 10c. tailing on a $6 head. In 1918 a 300-ton flotation mill using Minerals Separation machines was built based on the results obtained. However, when the mill began full-scale operation, mill heads did not come up to expectation, being only $4; also the-tonnage was considerably less than had been expected. Flotation mill tailing assayed 15c., indicating a recovery of over 96 per cent, so that excellent metallurgical results were obtained. The operation was a success but the patient died.

Jan 1, 1932

By H. P. Greenwald, H. C. Howarth

The rapidly increasing use in coal mines of portable auxiliary fans, which are generally 'blowers" employed in connection with canvas tubing, raises questions concerning the hazards of such equipment, especially where the practices are opposed to established methods of ventilating face workings. Half a dozen or more coal-mine explosions and some fires have been attributed to the use of auxiliary fans; moreover, competent mining engineers have found many dangerous installations and methods of use-for example, intermittent running of the fans in gassy mines with consequent accumulations of firedamp at the faces. These facts have led the U. S. Bureau of Mines to issue this recommendation: "In the interest of safety, the Bureau of Mines, Department of Commerce, recommends that auxiliary fans or blowers should not be used in coal mines as a substitute for methods of regular and continuous coursing of the air to every face in the mine." The comparatively recent introduction of new types of mining machines, mechanical loaders, face conveyors, and slabbing machines has encouraged the trial of new systems of face mining, all of which have for their object the rapid advance of the faces. Although the latter has certain economic advantages, in gassy mines the rate at which gas is given off is generally found to increase in proportion to the speed of advance into new territory, which in turn increases the difficulties of efficient ventilation of the face workings. Some of the systems of advance mining being tried in connection with new mechanizing methods practically compel the use of blower fans and tubing, as single narrow places arc now driven 300 ft. or more without crosscuts. In some instances a series of parallel headings are driven without crosscuts pre-

Jan 1, 1928

For many years it has been known that large bodies of iron ore existed in Iron and Washington counties in Utah. The ore is chiefly hematite-both hard and soft-though some magnetite is found. No definite and complete estimate of the iron ore reserves of the state have been made. The U. S. Geological Survey estimated that 40,000,000 tons of ore were disclosed by development work averaging only 35 feet below the surface of the ore. The ore is found along an area about one and a half miles wide by twenty miles long, and for the most part on the eastern and southern slopes or foothills of Three Peaks. Granite Mountain and Iron Mountain. Later estimates by others have gone as high as ore in sight 164,000,000 tons, probable ore 300,000,000 tons and possible ore 1,000,000,000 tons. Whether this last estimate is too great or not there is sufficient iron ore in Utah to justify the starting of an iron industry. Two companies are now mining iron ore in Utah, the Columbia Steel Corporation and the Utah Iron Corporation. The mine of the Columbia Steel Corporation is at Iron Springs a few miles west of Cedar City. About 650 tons, of ore a day is being shipped to the blast furnace at Ironton. The ore is mined by the glory hole method. After being drilled it is blasted to the bottom of the several glory holes and is dropped through chutes into cars on the ore haulage level below. It is then hauled by electric locomotives to the crushing plant, where it is crushed to blast furnace size before going to storage bins. Some of the softer ore is brought to the chutes by Fresno scrapers.

Jan 1, 1925

By Harrison Everett Ashley

(Pittsburg Meeting, March, 1910.) Slimes are usually defined as all material passing a certain-sized sieve, which is invariably the finest sieve employed by each metallurgist in his tests; 100-mesh and 200-mesh have been taken as the limits by different writers in recent volumes of the Transactions ; 150-mesh is common practice. The reader of the first two volumes of Richards 1 is impressed by the inflexibility with which all grinding-arrangements are praised or condemned according as they make little or much slime. Until recently, one of the principal aims of the mill-man was to keep down the slimes. He was obliged to have separate apparatus for sand- and slime-treatment. The latter was sometimes puzzling and erratic. Often it was found most .economical to omit treatment of the slimes entirely, or to store them in immense basins or heaps, waiting for possible future improvements in methods of treatment. Recently, improved processes of agitation and filtration have made possible the successful extraction of values from many slimes. The tendency, when the metal is exceedingly finely disseminated, is to cut out all sand-treatment and to slime everything. These processes have been almost entirely mechanical in their conception, and it is the object of the present paper to show that certain chemical considerations may greatly hinder or assist their successful operation. It has long been a source of dissatisfaction to chemists that their analyses fail to be of much help to the clay-worker; that it is a matter of common occurrence for clays of closely identical ultimate chemical constitution to show the widest possible divergence in physical properties. * Published by permission of the Director of the U. S. Geological Survey. Ore Dressing (1903).

Aug 1, 1910

By W. Griffith

The purpose of this paper is to make public record of new information in regard to the sustaining power of artificial mine-roof supports (not timber props), the result of investigations recently made in the anthracite coal fields of Pennsylvania. First.—By the "Scranton Mine Cave Commission," appointed to investigate the mining conditions under the City of Scranton. Second.—By the "Pennsylvania Mine Cave Commission," appointed by the Governor to investigate the general subject of mine caves in the anthracite region of Pennsylvania. Third.-—By the personal researches and tests made by the author in an effort to secure a better artificial mine-roof or surface support. During the progress of the work of the Scranton Mine Cave Commission, the Engineers for the Commission, Messrs. Conner and Griffith, being aware of the general lack of exact information in the engineering profession as to the strength of the ordinary artificial mine-roof or surface support, and particularly the stronger kinds, such as mine cogs, rock piers, etc., had tests made at the Fritz Engineering Laboratory at Lehigh University, to determine the sustaining power under various compressions of the several kinds of artificial mine supports in use in the anthracite region of Pennsylvania. A report of these tests wasincluded in the report of this Commission, which was published as Bulletin No. 25 of the United States Bureau of Mines, Washington. A similar series of tests, more extensive and more elaborately planned, were subsequently made for the Pennsylvania Minc Cave Commission at the U. S. Government Testing Laboratory at Pittsburgh, Pa. The report of this Commission was made to the Governor, but has not yet been published. The author, during his connection with the Scranton Mine Cave Commission, observed that of all the various devices employed for sustaining the roof of coal mines, the one universally used and the best

Jan 1, 1918

By Jacques B. Wertz

Among the parameters to be considered in the continuous search for new base-metal deposits, there often is a stratigraphic controlling factor that seems instrumental in the localization of ore. In British Columbia, for instance, the Upper Triassic as well as Lower Jurassic volcanics mixed with sediments are a useful indication in the search for copper while, in some parts of Australia, rhyolite bodies seem to be the favorable indicator, and this always within the geosynclinal environment. In Arizona, this stratigraphic factor becomes highly significant and it will be shown here that a large number of ore deposits are to be located around the flanks of ancient calcareous basins or depressions, preferentially corresponding to a certain optimum thickness as revealed by isopachs. The Martin limestone, of Devonian age, is already known for its basal O'Carroll bed which coincides with mineralization at places, and this is a relatively minor control. However, several limestone basins outlined by isopachs are in reality of greater importance as they localize mining districts. Indeed, most mines are found to coincide with a specific thickness of limestone while occurring simultaneously close to major, regional fracture intersections. The regional fractures in question were interpolated and extrapolated from known, important fault expressions, integrating quite well with the existing geology and further confirmed by minor criteria such as contacts, igneous plugs, axes of elongation of batholiths, dikes, etc. Although elements of subjectivity remain, this grid of fractures can be used quite successfully as a working hypothesis in the search for ore. Results of the present study which superposes major structural

Jan 1, 1971

By H. P. Greenwald

THE rapidly increasing use in coal mines of portable auxiliary fans, which are generally "blowers" employed in connection with canvas tubing, raises questions concerning the hazards of such equipment, especially where the practices are opposed to established methods of ventilating face workings. Half a dozen or more coal-mine explosions and some fires have been attributed to the use of auxiliary fans; moreover, competent mining engineers have found many dangerous installations and methods of use-for example, intermittent running of the fans in gassy mines with consequent accumulations of firedamp at the faces. These facts have led the U. S. Bureau of Mines to issue this recommendation: "In the interest of safety, the Bureau of Mines, Department of Commerce, recommends that auxiliary fans or blowers should not be used in coal mines as a substitute for methods of regular and continuous coursing of the air to every face in the mine." The comparatively recent introduction of new types of mining machines, mechanical loaders, face conveyors, and slabbing machines has encouraged the trial of new systems of face mining, all of which have for their object the rapid advance of the faces. Although the latter has certain economic advantages, in gassy mines the rate at which gas is given off is generally found to increase in proportion to the speed of advance into new territory, which in turn increases the difficulties of efficient ventilation of the face workings. Some of the systems of advance mining being tried in connection with new mechanizing methods practically compel the use of blower fans and tubing, as single narrow places are now driven, 300 ft. or more without crosscuts. In some instances a series of parallel headings are driven without crosscuts pre-

Jan 1, 1928

By J. F. K. Brown

ANTHRACITE in 1943, in common with the coal industry as a whole, passed through a year of wage negotiations that seemed endless. In the early months discussion of the United Mine Workers' demands was taken up and carried on continuously until May, finally reaching an impasse when the Union refused to continue at work, while submitting their demands to the War Labor Board. Thus a strike threatened, averted by the Federal Government taking over the industry, effective May 1, by order of the President. An office of the Bureau of Mines was established in Wilkes-Barre under the direction of J. J. Forbes, Mineral Production Security Division, as regional manager, who conducted operations until September, 1943, when the collieries were turned back to the operators. But the miners did not agree with the War Labor Board's award rendered in the fall, resulting in a recurrence of the previously threatened strike. again averted by Government control. In addition to the major upsets, a number of individual suspensions occurred at various mines. In spite of these drawbacks, to which might be added the difficulty of obtaining equipment and the scarcity of man power, the industry by November was only little less than a million tons short of the previous year. and in all probability, finally produced but little less than in 1942. This little less. however, was greatly missed in the market.

Jan 1, 1944

By James H. Hance

Several years ago the writer was connected with the Mint and Assay Service of the Federal Government as Assistant Assayer at the Salt Lake Assay Office. At that time cyanide bars formed approximately half of the bullion purchased by that office. Disagreement in valuat,ion between the producer and the office was not infrequent and to a lesser extent between the Assay Office and the Mint, this latter issue being soon obviated, however, by adopting uniform methods of sampling the bars. A nice problem seemed to offer itself for research and the writer began a series of experiments which were soon terminated, however, by his going into other work, and which he regrets have not since been completed. The results attained may suggest lines of approach to this problem and are, therefore, offered in this article. Frederic P. Dewey, Assayer of the Mint Scrvice, U. 5. Treasury, has had abundant opportunity to study this phase of metallurgy, and has published several articles relative thereto.1 In the last article cited Dewey quotes analyses of cyanide bullion similar in content to that with which the writer worked, and which show some of the variations met with. In the discussion of these papers,2 comparison has been made in terms of copper bullion, but to the writer this seems of questionable value. Copper bullion may resemble silver bullion, but its similarity to gold bullion with little or no silver content is another thing. The freezing-point diagram of Roozeboom, reproduced on page 881 of the discussion cited, is for the gold-silver series as stated. The original problem under discussion, however, is not this alloy but gold with base metals other than copper. As for the statement that the corners are the worst places or

Jan 1, 1916

By J. J. Mulligan, F. F. Colcord, E. F. Kern

The electrolytic separation of silver and gold has been practiced by the refineries in the United States for a good many years, and probably because of frequent visiting between officials of plants and the consequent exchange of views, operations in the various silver and gold refineries are very similar. We find, for instance, they practically all use electrolytes of approximately the same composition, which, no doubt, is more the result of experience than of studies of electrolytes. At the new electrolytic parting plant of the U. S. S. Lead Refinery, Inc., East Chicago, Ind., considerable attention has been given to the composition of electrolytes, especially to their conductivity and their effect on the character of the silver deposit. We are not aware that anything has been recently published on this subject and are, therefore, presenting such data as we have with the idea that, although it will not be wholly new, it may stimulate interest in the subject. Effect of Copper Content on Conductivity The first work was to determine the specific conductivity of silver nitrate and copper nitrate solutions. Concentrated solutions of silver nitrate and copper nitrate were prepared by dissolving analyzed chemically-pure salts in distilled water, and determining the silver and copper in each. Definite amounts of the concentrated solutions were taken, mixed and diluted to a definite volume. The silver and the copper were determined in each of these solutions and the conductivity was then determined. The plotted results are shown in Figs. 1 and 2. The effect of increasing quantities of silver and copper is readily seen. A comparison of the two sets of curves shows conclusively the benefit of holding the copper content of the electrolyte above 5C g. per liter, as its effect is to increase greatly the conductivity in an approximate propor-

Jan 1, 1926

By R. G. Woolery

INTRODUCTION Since 1975, Union Carbide Corporation has been conducting uranium exploration in southwestern South Dakota. This program has resulted in the discovery of an ore body about eight miles north of Edgemont in Fall River County. The site which was previously mined for uranium in the 1950's and 1960's consists of 950 lode claims (approximately 20,000 acres) and is within the Black Hills National Forest. Preliminary development plans indicate that fewer than 200 surface acres will be involved in the mining and heap leaching of the ore. The ore occurs in both the Fall River and Lakota formations. The exploration to date has developed something in excess of two million tons of ore averaging -0.1% U308. About 75% of the ore is expected to be mined from underground with 25% coming from five to seven small pits. The surface mining will be extensions of previously mined areas with a disturbance of 35-40 new acres near 35-40 previously disturbed acres requiring a total reclamation of 70-80 acres. Several options for processing the ore including conventional milling by UCC, conventional milling in joint venture with another producer, and heap leaching are under consideration. This paper is concerned with the preliminary assessment of the heap leaching option based on the limited test work conducted on surface samples and on available cores from the deeper ones. The final design for a commercial operation will not be available until an underground bulk sample has been obtained and evaluated. Union Carbide has been operating heap leach facilities commercially since 1973 at Gas Hills, Wyoming and Maybell, Colorado. During this period, we have made considerable progress in heap construction

Jan 1, 1983

By J. G. Benford, E. B. Stanley

THERE have been numerous papers in the literature1 on the subjects of secondary and tertiary recrystalli-zation in silicon steels. Secondary re crystallization is believed to occur in silicon steel by either a surface-energy phenomenon such as in the usual development of cube texture or by a second-phase phenomenon such as in the usual production of cube-on-edge texture, (110)[001]. Tertiary recrystallization in silicon steel is thought to be a surface-energy phenomenon in which, for example, grains having a (110) plane parallel to the sheet grow at the expense of other grains in the matrix including those having a (100) plane parallel to the plane of the sheet. In all these instances, the orientations involve either a preferred (100) or (110) plane in the plane of the sheet. Until very recently, there had been no experimental evidence reported of the occurrence of a texture by secondary or tertiary recrystallization that involves a (111) plane in the plane of the sheet, although Kohler reported that grains having the (111) plane parallel to the sheet surface can also grow by a surface energy mechanism. Stickels observed a secondary texture in iron described as "near {554}(225)" about 5 deg from {lll}(211).3 Mee reported that in a vacuum-remelted commercial 3 pct Si steel {lll}(hkl) secondary recrystallization took place in a high vacuum and in pure hydrogen.4 Recently in our Laboratory, large-grained structures such as shown in Fig. 1 having an orientation near (111)[211] or (111)[2ii] have been observed. The arrows point to areas of relatively small matrix grains of the kind that the much larger (111) grains consumed while growing. It is of interest that the matrix grains of samples annealed at 2000°F were essentially the same size as those in samples annealed at 2200°F, a matrix-grain-size stability that is characteristic of secondary recrystallization processes. A torque disc taken from Grain 4 of the sample shown in Fig. 1 revealed a very flat magnetic-torque curve, as expected, with a maximum torque of 7000 dyne-cm per cu cm compared to the typical 180,000 dyne-cm per cu cm observed for conventional (110)[001] textured material. A back-reflection Laue pattern for Grain 4 is shown in Fig. 2 and indicates a near-perfect (111)[211] orientation. The other six numbered grains in the sample of Fig. 1 had a similar orientation. The small circles next to each number were the target areas for the X-ray beam. The starting material was an 0.011-in.-thick oriented silicon steel, (110)[001] texture, containing 3 pct Si. It was lightly pickled, cold-rolled to 0.005 in., and annealed 4 hr at 2200°F within a nickel box (not gas-tight) inside a tube furnace through which dry hydrogen was flowing. The samples were heated to 1500°F in 1 hr and then at 60°F per hr to 2200°F. There were other

Jan 1, 1969

By F. F. Colcord

THE electrolytic separation of silver and gold has been practiced by the refineries in the United States for a good many years; and probably because of frequent visiting between officials of plants and the consequent exchange of views, operations in the various silver and gold refineries are very similar. We find, for instance, they practically all use electrolytes of approximately the same composition, which, no doubt, is more the result of experience than of studies of electrolytes. At the new electrolytic parting plant of the U. S. S. Lead Refinery, Inc., East Chicago, Ind., considerable attention has been given to the, composition of electrolytes, especially to their conductivity and their effect on the character of the silver deposit. We are not aware that anything has been recently published on this subject and are, therefore, presenting such data as we have with the idea that, although it will not be wholly new, it may stimulate interest in the subject. EFFECT OF COPPER CONTENT ON CONDUCTIVITY The first work, was to determine the specific conductivity of silver nitrate and copper nitrate solution. Concentrated solutions of silver nitrate and copper nitrate were prepared by dissolving analyzed chemically-pure salts in distilled water, and determining the silver and copper in each. Definite amounts of the concentrated solutions were taken, mixed and diluted to a definite volume. The silver and the copper were determined in each of these solutions and the conductivity was, then determined. The plotted results are shown in Fig. 1 and 2. The effect of increasing quantities of silver and, copper is readily seen. A comparison of the two sets of curves shows conclusively the benefit of holding the copper content of the electrolyte above 50 g. per liter, as its

Jan 2, 1926

R. B. BrinSmade, Ixmiquilpan, Hgo., Mexico (written discussion*).—While agreeing with Mr. Gibson that his net-profit tax is the fairest and best for mines, I believe that the tax he describes can be more accurately defined by another name. In accounting, net profits are usually considered to be the residual of the gross income after operating expenses and the annual charge for upkeep of plant have been deducted. Even the necessary interest on bonds or mortgages should not be subtracted in this calculation, for this interest represents merely that fixed portion of the net profits going as a return to that fraction of the total property value owned by the bondholders. Applying this method of calculation to the gross income of a mining property, we should onIy deduct operation expenses and upkeep of plant to get the net profits on its whole property value. So Mr. Gibson in deducting a further sum, to cover the interest and amortization of the capital expended in mine development and equipment, really arrives at something quite differen't from net profits; which can properly only be defined as the annual value of the mineral in the ground, or the royalty value in miners' parlance. From one viewpoint, Mr. Gibson's first principle, which assesses taxes, "proportionate to the benefits received by the person or property taxed," is identical with his third principle wbich assesses "with reference to the extent and value of the natural resources enjoyed." With one exception, everything of use around a mine represents a cash expenditure, or its equivalent in human labor, and state action has not added an iota to its value. The one exception is what makes the enterprise possible and it includes the mineral deposits and their associated surface; water and other landed rights. These natural resources are origin2!1y the gift of tile people acting through their agent, the state, and it is evident that a tax laid on whatever profits may arise from their enjoyment will be exactly "proportionate to the benefits received by the person or property taxed." Mr. Gibson is mistaken in his belief that the general property tax of the United States has the same incidence as his system of taxing profits, because the general property tax falls not only on land1 value—as does

Jan 1, 1920

By K. E. J. Rapperport, C. S. Hartley

The only slip system observed in zirconium crystals deformed at 77", 575", and 1075OK was (1010) [1210] with a critical resolved shear stress in tension of 1.0 kg per sq mm at 77°K; 0.2 kg per sq mm at 575 °K; and 0.02 kg per sq mm at 1075 OK. The active twin planes were {1012}, (1121}, (11221, and (11233) with varying temperature dependence. A detailed analysis for the slip direction using Laue spot asterism is appended. NeARLY all metals of the hexagonal close-packed structure exhibit basal slip, i. e.,(0002)<1120>- type slip. This is true of magnesium,&apos; zinc,&apos; cadmium,3 beryllium,4 titanium,= yttrium,6 and rhenium.Many of these such as titanium 5&apos;8-&apos;0beryllium,4&apos;" magnesium, and zinc13&apos;14 display other slip modes even at room temperature, and nearly all have been reported to slip on other systems under particular loading or temperature conditions of testing. As is shown in this paper, basal slip was not found at any of four test temperatures from 77" to 1075°K in hexagonal close-packed zirconium under the simple loading conditions of tension and compression, even though in one case the resolved shear stress on the inactive (0002) <llgO> system was twenty-five times higher than the critical resolved shear stress on the active (1010) [1210] system. This result is consistent with prior studies on the active deformation processes in zirconium deformed at room temperature. &apos;&apos;-I7 SPECIMEN PREPARATION A) Material—The zirconium used in this work was of two types: 1) as-deposited reactor grade crystal-bar, and 2) arc-melted and forged reactor grade crystal-bar. Typical chemical and spectrographic analyses of these materials as received, and after hydrogen removal and crystal growth are given in Ref. 17. Crystals of type 1) above have the letter prefix (A) and those of type 2) have the prefix (B) throughout this paper. B) Crystal Growth— he zirconium was machined into rectangular parallelepipeds about 0.2-in. scl in cross section and 2 in. iong. These were hand polished through 4/0 abrasive paper, electropolished, given a hydrogen removal anneal, and subjected to long-time anneals at 840 °C in vacuo to produce usable crystals.&apos;7 A second technique used to obtain large crystals was to cycle the samples two or three times between 1200" and 840°C, allowing them to remain at the higher temperature for about 4 hr and at the lower temperature for 5 days.17 These techniques yielded some grains which occupied the entire cross section of the bar and were as long as 3/4 in. C) Orientation Determination—After the growth of large crystals by thermal cycling, the samples were repolished with extreme care through 4/0 abrasive paper and electropolished. Metallographic examination after polishing showed the surfaces to be free of visible deformation traces. Standard Laue back-reflection X-ray techniques were used to find the crystallographic orientations of selected large grains with respect to a specimen face and edge. Fig. 1 shows the stereographic projections of the stress axes for the crystals used. The sharpness of the spots on the Laue photographs indicated that the crystals were of good quality. EXPERIMENTAL METHODS Nine crystals were deformed in tension at 77"K, nine in tension and five in compression at 300°K in previous tests,17 fifteen in tension at 575"K, and eleven in tension at 1075°K. All specimens were stressed by load increments. After a predetermined load was applied, the specimen was removed from the loading appratus and metallographically examined for deformation traces. An attempt was made to initially stress each bar so that some crystals slipped a small amount and others not at all. This was done to bracket the critical resolved shear stress. One bar of special orientation (B-11) was repolished and annealed at 1075°K for 1 hr after lower temperature deformation, before final deformation at 1075°K. In the other bars the loading by increments, followed by metallographic examination, was continued until the surface distortion would interfere with analysis, or until fracture. One example of a crystal pulled to fracture is shown in Fig. 2. This photograph shows a crystal (B-14C) which was pulled at 1075°K and failed by slip on two (10i0) planes. The approximate orientation of this crystal is illustrated in the figure. Specimens were deformed at 77°K in liquid nitrogen on a tensile machine using an insulated bucket with an internal hook to accept a clamped specimen.

Jan 1, 1961

By J. A. Retty

HOLLINGER CONSOLIDATED GOLD MINES LTD., through two subsidiary companies, has the exclusive right to prospect in two contiguous areas in central Labrador. This paper presents the results of the mineral exploration that has been conducted in these areas to date. One of the subsidiaries of Hollinger. the Labrador Mining and Exploration Co. Ltd., under an agreement with the Newfoundland Commission of Government, holds an area of approximately 20,000 sq.mi., which comprises the western portion of Newfoundland-Labrador and includes the upper basins of the Hamilton and Naskaupi Rivers. (The main area of the deposits so far discovered may be located on a map at about 67° west longitude and 55° north latitude.) The other subsidiary of Hollinger, Hollinger North Shore Exploration Co. Ltd., has licensed from the Province of Quebec an area of approximately 3900 sq.mi. lying directly north of the Newfoundland-controlled area at the headwaters of the George, Whale, and Swampy Bay Rivers. The M. A. Hanna Co., large iron-ore operators of the Lake Superior region, are participating in the project. With the exception of the years 1940 and 1941, field work has been conducted in the Newfoundland area since 1936, and in the Quebec area since 1939. Hollinger assumed the management in 1942. The field base is at Hollinger Lake, some 300 miles north of the tidewater base at Seven Islands, Quebec, which, in turn, is just west of the mouth of the Moisie River, on the Gulf of St. Lawrence. Air transportation is used exclusively to service the operation.

Jan 1, 1945

F. C. HENDERSCHOTT,* New York, N. Y.-I am going to take, as the text of what I shall discuss, a portion of the second paragraph of Mr. Stanford&apos;s paper. It read as follows: "The most vital need of the management is for more brains. The logical course for an engineer ;in charge of an industrial organization is, therefore, to direct whatever forces may be at his command toward the development, training and guiding of-all the brains in his organization. This is easier said than done, for it involves the carrying on toward two objectives, the maximum of productive work and the development of the individuals, who perform it;" and the last sentence of the paper; "Industry has no greater asset than an intelligent workman." The United States of America, at the outbreak of the present war, had the best equipment of any nation in the world. That statement holds not only for our -shops and our transportation systems and our stores and our farms and our homes, but it holds generally.. There was no other nation in. the world that had so good equipment as the United States. There was no other nation in the world that could be called progressive that has such poorly trained workers as the United States. Even Norway, Denmark, Sweden and New Zealand ranked ahead of us. Now that is the, problem, generally speaking, and there was recognition of that fact, a growing recognition which-took form, and one of its forms was what we call the corporation school. Now obviously a corporation has no particular educational functions, but as is said in the closing sentence of Mr. Stanford&apos;s paper, or as is implied, an industrial institution is, after all, the reflection of the aggregate of the efficiency of the individuals who compose that organization. There is no way of getting away from that. If your individuals, from your president down, are efficient, if your individual has developed his brains, if he is a trained man, you have got an efficient organization, and if you haven&apos;t that condition, you have got weaknesses and your organization is no stronger than those weaknesses. I maintain that the same thing holds for a nation; .a nation is as efficient as the collective efficiency of the individuals who compose the nation, and no more so.

Jan 4, 1918

By Rossiter W. Raymond

The formal outline of Mr. Hague&apos;s life and work is embraced in the following statement, chiefly based upon data furnished by him, at my request, shortly before his death. At that time the probability that I would survive to record his death was apparently small; but I urged upon him the duty of providing, whether for me or for my successor as Secretary of the Institute, trustworthy material for the notice which somebody would some day have to write—and which might otherwise be incomplete or incorrect. Mr. Hague, with characteristic promptness and freedom from affectation, did what I asked of him; and I am therefore able to present an authoritative sketch—concerning the details of which I shall add my own comments, and some particulars obtained from friends. James Duncan Hague was born Feb. 24, 1836, at Boston, Maes., where his father, Rev. William Hague, D.D.,an eminent clergyman, then resided. After a preliminary education in private schools, he studied in 1854 at the Lawrence Scientific School of Harvard University; in 1855 and 1856 at the University of Göttingen, Hanover; and from 1856 to 1858 at the Royal Mining Academy of Freiberg, Saxony. In 1859-1861 he was attached as chemist to a South Sea exploring expedition, sent by W. H. Webb, of New York, to examine Jarvis, Baker, and other islands for phosphate-deposits. After the outbreak of the Civil War, he entered the U. 5. Navy, serving for a year as Judge Advocate to the fleet stationed at Port Royal, S. C. In 1863 he became Superintendent of the Albany and Boston copper-mine, in the Lake Superior region, where he was also connected with the earliest development of the Calumet and Hecla property. In 1867 he became the First Assistant Geologist in Clarence King&apos;s famous Exploration of

Jan 1, 1909