Search Documents

By Charles V. Jenkins

The structure of steel, when rendered coarse by over-heating, is made fine by re-heating to a certain temperature, the determination of which has received much attention from eminent metallurgical authorities. Among these, I may particularly mention Prof. D. Tschernoff' [Chernoff], who, about thirty years ago, studied this question in connection with his investigations on the structure of steel in genera1. † Some years later, Mr. J. A. Brinell took up the inquiry, and arrived at many important conclusions, stated in his well-known rules on the treatment of steel. ‡ These two gentlemen, however, based their reasoning chiefly upon the aspect of fractures—a method which, though it affords valuable information, does not readily reveal the different steps by which a change in structure takes place. For further light on the subject, we owe much to more recent microscopic investigations, which have made us better acquainted with the internal structure of metals. Such an investigation, closely connected with the present subject, and made by Mr. John E. Stead a few years ago, was first published in 1898.6

Jan 1, 1903

By J. J. Becker

Changes in magnetic properties with particle size are used to study the precipitation process in a Cu-Co alloy. In particular, the effect of a field during aging in producing anisotropy is shown to occur entirely during the growth of the particles, after precipitation is complete. HEAT-treatment in a magnetic field is done commercially to improve the magnetic properties of a number of materials. These can be divided into solid-solution alloys and precipitation alloys. The Permalloys are representative of the first type, and magnetic annealing greatly increases their maximum permeability. On the other hand, in precipitation alloys such Alnico 5 the important result is an increase in maximum energy product. The effect of the field in all cases is to bring about an additional magnetic anisotropy, uniaxial in nature, which makes the hysteresis loop more upright when measured in the direction in which the field was applied. The structural origin of the anisotropy brought about by magnetic annealing is not well understood. In the solid solution alloys, one possible explanation is based on ordering.' Another possibility is the orientation of like-atom pairs.' The precipitation systems known to respond to magnetic heat treatment are Alnico 2, in which the effect was first discovered," Alnico 5, cobalt ferrite (oxide),' and Cu-Co alloys.3 n these materials, the field affects the precipitation process itself in some way. Although there has been much work on Alnico 5. its nature is still incompletely understood. According to Geisler,' the precipitation reaction is of the

Jan 1, 1959

By Chas Dobbel

THE Chief Consolidated properties are situated in the Tintic mining district of Utah, being included in Juab and Utah Counties, about 70 miles south of Salt Lake City. The drilling referred to in this paper has been carried on in the Chief Consolidated No. 1 mine, the Gemini mine, and the Eureka Hill mine at Eureka, the Grand Central mine, above Mammoth, and the Apex Standard mine just south of Dividend. The occurrence of ore through the district is typically in lenses on bedding or breaks, and in connecting pipes, without accurate geometrical trend so that the ratio between the total length of development in drifts and crosscuts to the square feet of ore exposed is very high. A section of one of the western channels (Fig. 1) through the Tintic district, shows, roughly, the irregularities calling for excessive development work, so typical of the Tintic mines. This irregular trend of the ore constantly calls for excessive cutting up of the whole area for offshoots and the connecting links always present.. In the planning of prospecting and development, no regular system may be laid out without overlooking some orebodies or segments of orebodies. It was with these facts in mind that Cecil Fitch, the general manager of the Chief Consolidated Mining Co., decided that some method of drilling was the more feasible way of successfully cutting up and bringing about the discovery of ore believed to exist; yet this drilling had to compete with a great. margin of cost over crosscutting, as a crosscut in the Tintic district, even though barren, brings out geologic facts that, in many cases, are worth the price of the working itself. Diamond drills met with the success that might be expected in a district that has a reputation for the wear and loss of diamonds; after 6 or 8 months, this method was discarded on account of the high costs. Simultaneously, a small churn drill outfit was set up underground but a few shifts proved its inapplicability. At the same time, the ordinary hammer drill was usd to drive prospect holes with jointed steel.

Jan 9, 1925

By W. G. Jewitt

YELLOWKNIFE, the most northerly Canadian gold mining district, is once more in the throes of a boom. Touched off by spectacular and well-publicized diamond-drilling results on the property of Giant Yellowknife Gold Mines, Ltd., mining companies and the general public are competing for mining claims and for the shares of companies owning mining claims in the area, with little regard for values. Such a stock-market boom has various unfortunate consequences but undoubtedly one beneficial result is that considerable amounts of money are made available for serious development. The Yellowknife mining area lies on the north shore of Great Slave Lake, in the Northwest Territories, at a latitude of approximately 62°30' north. The topography is a low-relief phase of that usual in the Canadian Laurentian shield. Roughly, one third of the surface is lake-covered, one third muskeg or overburden, and one third is bare

Jan 1, 1944

By Walter Kauzmann

ALL viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.[t] Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem -i.e., the dependence of shear rates on temperature, stress, etc.-from the standpoint of recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of applications1 RESOLUTION OF MACROSCOPIC SHEAR INTO MICROSCOPIC MOVEMENTS; RESEMBLANCE TO CHEMICAL REACTIONS Just as any large body is made up of many small units, or atoms, so macroscopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for nonturbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove. In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker,4 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the

Jan 1, 1941

By E. S. Machlin, S. Weing

GRAIN boundary stress relaxation has been the subject of several investigations in recent years, but as yet the phenomenon is not well understood. One of the major difficulties has been the lack of a sufficient amount of data with which to evaluate any proposed mechanism. Little information is available on the effect of small amounts of substitutional solutes on grain boundary stress relaxation. It is with this important phase of the problem that this investigation is concerned. The influence of substitutional solutes on grain boundary stress relaxation has been recently investigated in copper by Pearson: and in aluminum by Dorn et al.' Pearson studied the effect of zinc, gallium, germanium, and arsenic on the relaxation peak of OFHC copper.* The pure OFHC copper decreased the peak intensity and a second peak appeared at a higher temperature. This latter peak was termed the alloy grain boundary peak. At the lowest binary concentration studied, approximately 1 atomic pct, the primary peak was almost completely obliterated. Pearson found that the activation energy calculated from the alloy grain boundary peak for all solutes, irrespective of the concentration, was 44,000 cal per mol. Pearson concluded that the increase in activation energy from 33 to 44 kcal per mol is not continuous but abruptly changes from the lower to the higher value. As no attempt was made to investigate the intermediate range of concentration and hence calculate the possible variation of the activation energy for the initial grain boundary peak, this conclusion is hardly valid. In contrast to these results, Dorn et al. studied the effect of zinc, silver, copper, germanium, and magnesium on the grain boundary stress relaxation of aluminum. No change in the energy of activation was observed for binary alloys of the flrst four solutes, but a linear increase was found for increasing concentration of magnesium. Saturation was not found up to the maximum of 1.6 atomic pct. The energies of activation were obtained by plotting the horizontal displacement of the dynamic modulus curve vs temperature for two vibrational frequencies. As the modulus is proportional to the square of the frequency, this requires the measurement of the torsional frequency over a range of temperature. However, the technique does not lead to an unambiguous interpretation of the grain boundary

Jan 1, 1958

By R. M. Daelen

Mechanical science is severely tested by the demands of the iron manufacture for the varied apparatus needed to transport and to treat raw materials and products. Water has long been a favorite means of transmitting pressure for such purposes, because of its own incompressibility. Further advances in its use are the more to be expected, since mechanical improvements have steadily tended to overcome the difficulties formerly encountered in the employment of great hydraulic pressures. So long as the pressure is not higher than that which requires for plungers, etc., only ordinary stuffing-boxes, with hemp or other similar packing, the necessary arrangements for the production and transmission of the water-pressure without leakage are very simple. But when this limit (which is, for most purposes, 50 kilos to the square centimeter) is exceeded, new conditions of construction arise, which are met in various ways, and which justify a primary division of hydraulic presses into low-pressure and high-pressure respectively. The former are used in lifting and moving weights, and employ pressures as high (in extreme cases) as 100 kilos per square centimeter; but at this point the friction between piston and hemp-packing is so great that the use of cup-leathers is already preferable. Beyond 100 kilos it becomes a necessity. The range of practicable tight packing which follows is considerable, extending to about 1000 kilos; but "high pressure" in practice is from 100 to 600 kilos, and it is to this that the present paper applies. General Classes and Types. Hydraulic transmission at high pressure usually claims consideration in case the solid mechanism, such as levers, cams, screws, and gear-wheels, would have to be too large, would involve too much friction, or could not be suitably adapted to the speed-requirements of the working-tools. Since steam is mostly the primary carrier of

Jan 1, 1893

By B. T., Colley

AS always when metallurgical operations are conducted within or close to agricultural and stock-raising regions, the question of damage due to fume and smoke presented itself when the Cerro de Pasco Copper Corporation's new smelter commenced to operate in La Oroya in 1922, For more than twenty years the Corporation had operated its old plant close to Cerro de Pasco without encountering difficulties from smoke claims, owing to the fact that it was in an open plain where more or less constant air currents carried and dissipated the smoke over large areas, affording ample dilution. But Oroya is in a deep canyon formed by four contributing valleys up and down which the smoke travels for long distances in a more or less concentrated form. Though the altitude of Oroya is more than 12,000 ft., and the surrounding country rises to much greater elevations, nevertheless there exists there a large and important stock-raising industry and also a considerable development in agriculture, consisting of the cultivation of potatoes, barley, etc.

Jan 1, 1945

By W. A. Backofen, G. Y. Chin, W. F. Hosford

The effect of machine stiffness on discontinuous flow and fracture of the 2024 aluminum alloy was studied in tension at 4.2OK. An increase of machine stiffness was found to decrease the amount of elongation and drop in load during discontinuous flow, thereby postponing fracture to larger strains and higher stresses. The possibility of utilizing stiffened tools in deformation processing to suppress shear fracture originating from unstable flow was indicated. The problem of nucleating discontinuous flow and the role of the effective mass of the system in discontinuous flow were also considered. AT low temperatures the plastic flow of metals is often discontinuous, with sudden load drops and elongations.1,3 Basinski1,4 has presented strong evidence that discontinuous flow, at least in aluminum alloys, occurs under nearly adiabatic conditions. During testing the load may drop suddenly and flow become localized when the thermal softening, due to heat generated in plastic straining, is greater than the strain and strain-rate hardening. This instability criterion is more easily satisfied at low temperatures because 1) the volume specific heat is reduced so that relatively large temperature increases are possible in straining, and 2) the flow stress is relatively temperature-dependent. The important role of adiabatic shear in ductile fracture processes has been emphasized,5-1 and consideration has already been given to the influences of thermal and mechanical properties on the tendency of a material to undergo adiabatic shear.17677 By focusing attention on how the mechanical loading system influences low-temperature discontinuous flow, additional insight into adiabatic shear and its effect on fracture may be gained. EXPERIMENTAL PROCEDURE Because of its low thermal conductivity, the 2024 aluminum alloy exhibits a highly consistent discon- tinuous-flow behavior at 4.2°K and was therefore chosen as the material for study. Machined specimens of 0.113 in. diam and 1.125 in. gage length were solution heat-treated at 490°C for 3 hr, quenched into cold water, and immediately immersed in liquid nitrogen until just before testing. Testing was done at 4.2°K by immersion in liquid helium at a crosshead drive rate of 0.03 in. per min. As normally used (hard-machine basis), the spring constant of the testing machine was k = 25,000 lb per in. By inserting beam springs in series with the specimen, this value could be lowered by a factor of about 100. Details can be found elsewhere.? As a result of variable machine stiffness, the actual strain rate ranged from about 3 x 10 5 to 3 x 10-4 per sec from one test to another, as well as within any one test. However, preliminary tests had established that the tensile curves were not altered significantly by this strain-rate variation. Fig. 1 shows a typical load vs plastic-elongation curve for a solution heat-treated 2024 aluminum alloy specimen pulled in the standard hard machine (k = 25,000 lb per in.) at 4.2"K. The elastic extension has been subtracted. Plastic flow proceeded smoothly from yielding at approximately 22,000 psi (load = 220 lb) to a strain of about 4 pct at which point the flow became discontinuous. The magnitude of the load drops as well as the plastic elongation per drop increased with increasing strain until the specimen finally broke abruptly. The load-elongation behavior of a sample tested with a relatively soft machine under otherwise identical conditions is given in Fig. 2. In general, there

Jan 1, 1964

By Charles W. Goodale, William A. Akers

The treatment of silver-ores of too low a grade to justify either smelting or preliminary roasting, and yet not " free" enough to permit of raw amalgamation, has ever been a serious problem. As bearing upon it, the operations of the Combination Mining and Milling Company of Black Pine, Deer Lodge county, Montana, during the past year may not be without interest. It is not claimed that the process to be described is not susceptible of great improvement, nor is any claim of originality made for it; but its use is, as yet, not very general, and it seems to offer a means of profitably working the large class of partially-decomposed argentiferous ores which, by reason

Jan 1, 1890

By I. A. Lange, A. M. Richardson

Although methods for determining shaft lining thickness are well documented, little attention has been given to the design of station breakouts and other related shaft ground support structures. This paper discusses design of selected shaft structures for the Cathedral Bluffs project, a planned 54-kt/d (60,000-stpd) oil shale mine in western Colorado. Design philosophy and construction sequences used in the three completed 520-m (1700 ft) deep, 4.6-m (15 ft) to 10.4-m (34-ft) diameter shafts are described.

Jan 1, 1984

By T. R. Scott

The acid pressure leaching of zinc-lead flotation concentrates from the McArthur River deposit, Northern Territory, Australia, has been studied in a three-stage, continuous, co-current system, using titanium reactors of 6 gal capacity. The starting pulp contained 2.7 lb solids per gal of synthetic spent electrolyte and the final liquors contained 120-125 gpl Zn. Parameters investigated included temperature (95-120°C), oxygen pressure (30-100 psi), acid addition (80-130% of theoretical), and leaching time (35-65 min per stage). Technical factors studied included mixing and pumping of feed, agitation, settling and washing and control mechanisms. The chemistry of liquor impurities, of scale formation in autoclaves and of lead jarosites in residues was studied in some detail. Results indicated that 90-93% zinc recovery could be obtained with a "low- acid" process, using 113°C and 70 psig with oxygen as the favored operating conditions. Residues contained 16-18% elemental sulphur and 15% lead, together with unreacted pyrite and gangue minerals. Pelletizing of residues was impracticable, and alternative suggestions for the recovery of lead, sulphur and silver are discussed. Preliminary estimates for plant and operating costs are given and enable some comparison to be made with conventional procedures.

Jan 1, 1973

By Herman Dykstra, R. L. Parsons

A numerical method for solving partial differential equations in steady state fluid flow is described. This method, known as the "relaxation method," has two advantages over analytical methods: (1) practically any problem can be solved, and (2) a solution can be obtained quickly. A disadvautage is that the solution is not general. The method is applied to core analysis and relative permeability measurement to calculate constriction effects and to calculate the true pressure drop measured by a center tap in a Hassler type relative permeability apparatus. Further applications are suggested. INTRODUCTION Many problems in fluid flow cannot be solved analytically because of the nature of the boundary conditions. For many problems, however. an exact answer is not necessary because boundary conditions are not exactly defined or the parameters describing the porous medium are not accurately known. The relaxation method can be used to obtain an approximate answer easily and quickly for the flow of incompressible fluids in porous media. The method can also be used for other types of problems, such as determining the stress in a shaft under load. or the temperature distribution during steady state heat flow. In this discussion only calculations concerned with the flow of fluids in porous media will be considered. The method was introduced by R. V. Southwell in 1935.' THEORY The treatment given here follows that given by Enimons.2 Consider a porous medium to be replaced entirely by a net of tubes of equal length and uniform cross-sectional area as shown in part in Fig. 1. Assume that the net of tubes behaves exactly like the porous medium which it replaces; that is, the net can be made fine enough to reproduce exactly the porous medium. Assume also that Darcy's Law can be used to calculate the flow from one point to another point through these tubes. The flow from point 1 to point 0 is KA . ------ P-P) .......(11 where a is the distance between points: K is the "permeability" of a tube; A is the cross-sectional area of a tube; is the viscosity of the liquid in the porous medium; and (P1 — P0) is the pressure difference between point 1 and point 0. In like manner the flow can be calculated from points 2, 3, and 4 to point 0. The net flow into point 0 is Qo = KA/µa (P1 + P2 + P33 + P4-4P0) . . (2) MB For an incompressible fluid the net flow into point 0 will be zero or, Q. = 0. This says that at point 0 fluid is neither being accumulated nor depleted. 'Therefore. P1 + P2 + P3 + P4 - 4P0 = 0 .... (3) . If. now. with specified boundary conditions. the pressure i.; known at a finite number of points in a given region, as at the points shown in Fig. 1, Equation (3) will be satisfied at every point. If, on the other hand, the pressure is not known, the pressure can be guessed at these points. Then. unless the guess is perfect. Equation (3) will not be satisfied at all of the points. When Equatiol~ (3,) is not satisfietl. let d = P1 + I?, + P, + P, - If' .,....(4) where 6 is an apparent error and is called the residual at point 0. Equation (4) shows how much the pressure guess is in error at point 0 with respect to the surrounding points. A positive residual means that the pressure is too low, and a negative residual means that the pressure is too high. To bring the residual, 6. to zero in order to satisfy Equation (3). it is necessary to make changes in the pressure guesses. Equation (4) shows that a +1 change in Po will change the residual at point 0 by -4. A +1 change in the pressure at any of the four surrounding points will change the residual at point 0 by +l. Thus it can be seen that a change at any point will affect the residual at that point and the four surrounding points. By changing the pressure from point to point, all of the residuals can eventually be brought nearly to zero and the problem will be solved. This procedure is the essence of relaxation methods and is used to relax the residuals so that Equation (3) is satisfied at every point. The procedure can be most easily explained in detail by solving a simple problem. as Southwell says, "To explain every detail of a practical technique is to risk an appearance of complexity and difficulty which may repel the reader. A

Jan 1, 1951

By R. L. Parsons, Herman Dykstra

A numerical method for solving partial differential equations in steady state fluid flow is described. This method, known as the "relaxation method," has two advantages over analytical methods: (1) practically any problem can be solved, and (2) a solution can be obtained quickly. A disadvautage is that the solution is not general. The method is applied to core analysis and relative permeability measurement to calculate constriction effects and to calculate the true pressure drop measured by a center tap in a Hassler type relative permeability apparatus. Further applications are suggested. INTRODUCTION Many problems in fluid flow cannot be solved analytically because of the nature of the boundary conditions. For many problems, however. an exact answer is not necessary because boundary conditions are not exactly defined or the parameters describing the porous medium are not accurately known. The relaxation method can be used to obtain an approximate answer easily and quickly for the flow of incompressible fluids in porous media. The method can also be used for other types of problems, such as determining the stress in a shaft under load. or the temperature distribution during steady state heat flow. In this discussion only calculations concerned with the flow of fluids in porous media will be considered. The method was introduced by R. V. Southwell in 1935.' THEORY The treatment given here follows that given by Enimons.2 Consider a porous medium to be replaced entirely by a net of tubes of equal length and uniform cross-sectional area as shown in part in Fig. 1. Assume that the net of tubes behaves exactly like the porous medium which it replaces; that is, the net can be made fine enough to reproduce exactly the porous medium. Assume also that Darcy's Law can be used to calculate the flow from one point to another point through these tubes. The flow from point 1 to point 0 is KA . ------ P-P) .......(11 where a is the distance between points: K is the "permeability" of a tube; A is the cross-sectional area of a tube; is the viscosity of the liquid in the porous medium; and (P1 — P0) is the pressure difference between point 1 and point 0. In like manner the flow can be calculated from points 2, 3, and 4 to point 0. The net flow into point 0 is Qo = KA/µa (P1 + P2 + P33 + P4-4P0) . . (2) MB For an incompressible fluid the net flow into point 0 will be zero or, Q. = 0. This says that at point 0 fluid is neither being accumulated nor depleted. 'Therefore. P1 + P2 + P3 + P4 - 4P0 = 0 .... (3) . If. now. with specified boundary conditions. the pressure i.; known at a finite number of points in a given region, as at the points shown in Fig. 1, Equation (3) will be satisfied at every point. If, on the other hand, the pressure is not known, the pressure can be guessed at these points. Then. unless the guess is perfect. Equation (3) will not be satisfied at all of the points. When Equatiol~ (3,) is not satisfietl. let d = P1 + I?, + P, + P, - If' .,....(4) where 6 is an apparent error and is called the residual at point 0. Equation (4) shows how much the pressure guess is in error at point 0 with respect to the surrounding points. A positive residual means that the pressure is too low, and a negative residual means that the pressure is too high. To bring the residual, 6. to zero in order to satisfy Equation (3). it is necessary to make changes in the pressure guesses. Equation (4) shows that a +1 change in Po will change the residual at point 0 by -4. A +1 change in the pressure at any of the four surrounding points will change the residual at point 0 by +l. Thus it can be seen that a change at any point will affect the residual at that point and the four surrounding points. By changing the pressure from point to point, all of the residuals can eventually be brought nearly to zero and the problem will be solved. This procedure is the essence of relaxation methods and is used to relax the residuals so that Equation (3) is satisfied at every point. The procedure can be most easily explained in detail by solving a simple problem. as Southwell says, "To explain every detail of a practical technique is to risk an appearance of complexity and difficulty which may repel the reader. A

Jan 1, 1951

By S. K. Asunmaa, W. D. English, N. A. Tiner, W. A. Cannon

This paper discusses the reaction of metal surfaces with fluorine. Fluorination reactions result in the formation of metal fluoride films which are "passive" toward further reaction of the metal with fluorine. These films are very adherent, and do not easily detach from the substrate metal by mechanical flexing or thermal shock. Exposure of passive films to a humid atmosphere produces hydrated metal fluorides which cause secondary fluorination reactions upon reexpo-sure of the metal surface to fluorine. The surface films formed range from 10 to 30A in thickness and they pow at the expense of surface oxide films. The apparent film formation is completed rapidly in 15 to 30 min on stainless steel and nickel surfaces. On copper and on Monel surfaces, the film at first grows rapidly, then increases slowly over an extended period of time. Passive films are formed at all fluorine pressures in the range from 0.1 to 1.4 atm at room temperature. ALL metals react when exposed to fluorine. These reactions generally produce surface films which consist of metal fluorides. The rate of reaction is largely determined by the extent to which these films are protective. Although there is an extensive literature concerning reactions of oxygen with metals, there are very few investigations reported concerning fluorine-metal reactions. Brown, Crabtree, and ~uncan' investigated the kinetics of the reaction of gaseous fluorine with copper metal which had been freshly reduced in hydrogen. The reaction rate was independent of pressure over the range from 6 to 60 torr. A logarithmic rate law was obeyed in the temperature range from 25" to 300" ~. There was some deviation at higher temperatures which could have been the onset of a parabolic law. The calculated film thicknesses ranged from about two molecular layers, 10A, for 5 hr exposure at room temperature to thirty-five molecular layers for 5 hr exposure at 200" . The authors concluded that no single mechanism could explain all the observations. O7Donnell and spatkowski2 studied the reaction of fluorine with copper at 450°C at pressures from lo to 133 torr. The reaction was found to be pressure -dependent and followed a logarithmic rate law. It was not entirely diffusion-controlled, and fluorine was thought to be the migrating species in the reaction. Miscellaneous metal-fluorine reactions were investigated by Haendler et ~1.~ Reaction products were identified but no rate data were determined. Air Prod- ucts and Chemicals, Inc., have conducted an investigation of reactions between fluorine and various metal powders at room temperature and 85° C. Fluoride film thickness as a function of time of exposure was reported on the assumption that the reaction takes place between fluorine and metal to form the normal metal fluoride. Surface areas of the powders were only estimated so the relative film thicknesses may not be exact. The data showed reaction rates which were generally logarithmic in character, the rate of film growth virtually ceasing after a few hours exposure time for some alloy powders. The effect of moisture on fluoride films was also investigated by measuring additional reaction with fluorine after exposure of passivated powders to atmosperic moisture. The fluorination of iron was studied by 0'~onnell~ at temperatures from 225" to 525" ~ and at pressures ranging from 20 to 200 torr. In all ranges, the reaction followed a logarithmic rate law and was dependent on the square root of the gas pressure. The author concluded that fluorine gas passes through pores in the film. As the film grows, the blocking of pores leads to a rapid decrease in reaction rate; hence a logarithmic rate law is observed. Jarry, Fischer, and Gunther' investigated the mechanism of the reaction of fluorine with nickel at about 600" to 700°C. On the basis of the metallographic examination of fluoride scales growing on the nickel and from separate radioautographic data, it was claimed that fluorine is the migrating species in the reaction. This is in sharp contrast to the growth of oxide films on nickel where it has been shown that nickel ions migrate through the scale to the gas-solid interface to react with oxygen. Few investigations have been reported of the reaction of fluorine with metal oxides. Such investigations should be of great significance for a better understanding of passivation in view of the ubiquitous oxide films on technical alloys. Haendler et al.3 studied the reaction of fluorine with oxides of copper, tin, titanium, zirconium, and vanadium. Copper (I) oxide reacted as follows in the temperature range 150" to 300"~: temperature above 300" ~ was required for the CuO to react to form additional copper fluoride. Ritter and smith7 also investigated the reaction of fluorine with copper (11) oxide. An oxide powder comprised of spherical particles with a fairly high surface area was reacted with fluorine, starting at room temperature and increasing to 100° C over a period of 3 or 4 hr. The initial reaction was slow until the fluoride film thickness reached about to or 15R at which time the reaction rate accelerated, then decreased again. Most of the kinetic data was obtained during this final phase of reaction. The authors conclude that the film grows slowly at first until the stresses developed in the distorted lattice are sufficient to rupture the initial

Jan 1, 1969

By J. P. Savely, D. E. Nicholas, R. D. Call

Progress in the technology of slope design over the past 15 years now permits the selection of rational slope angles if suitable data on geology, hydrology, and rock properties are available for a specified project. Although a full-scale slope design study remains the best course of action, there are situations where an extensive study is not feasible due to time or budget constraints. Two typical examples are: (a) selecting pit slope angles for a preliminary feasibility study at the exploration stage; and (b) coping with a slope failure in an operating mine. In both instances, slope angles must often be chosen on the basis of data that are currently available or can be readily obtained. All too often during exploration programs, a feasibility study is initiated shortly before the decision deadline to drop the property or proceed to purchase. If the only existing data at this point are a few cross-sections at odd angles showing ore and waste contacts or a dog-eared map of the surface geology, there may not be time to collect and organize sufficient information for the design of slope angles. On the other hand, if during the drilling program geologic cross-sections were constructed and the structural data compiled in tabular form, rational slope angles could be computed within the allotted time.

Jan 4, 1977

By Benjamin Tillson

To MOST mine operators, it seems evident that there is a drill-steel problem, although under certain conditions the amount f drill-steel breakage does not appear serious. What is at fault? It may be one or a combination of circumstances. The development of rock drills to the hammer-drill type in place of the old reciprocating piston drill, probably is one important cause for the greater steel breakage. Perhaps the manufacturers of drill steel have failed to realize what alloys are needed for this new service or have overlooked the changes in the art of rock drilling. Although suitable alloys are provided, they may not be so handled in the manufacturing process as to be in the best condition to withstand the demands of rock drilling. The mine operator may be at fault in desiring to use the smallest possible drill-steel section in order that the gage of the drill bits may be correspondingly small and the amount of footage drilled per unit of labor may be greater; or the black-smithshop practice at the mines may need improvement. The miner who uses the drill steel may also require more intensive supervision and education. Again, the manufacturer of rock drills may have failed to study the types of blows the steel alloys will withstand satisfactorily and which their tools are delivering and so he may not know whether or not a different design of rock drill would equal or excel their present drilling speeds without treating the drill steel so severely. All of these hypotheses probably have their supporters. On the other hand, perhaps we are seeking too much service from drill steel and we need a fuller realization of the fatigue strains developed and should prepare to relieve these by a periodic heat treatment of the steels. However, we do not find any proof that any of these suppositions may be held responsible for the drill-steel breakage attendant to mining. The proposed investigation of this matter by the U. S. Bureau f Mines is fully warranted in the promotion of the conservation of labor and material, and the safety of the workmen. The great range of field conditions, as well as the scope of the research, requires the energetic cooperative support of many interests. Various manufacturers of steel,

Jan 5, 1921

By W. S. Ayres

THE boiler from which these stay-bolts have just been obtained was that of the locomotive Catasauqua, Lehigh Valley Railroad, built at the company's shops, South Easton, Pa., in 1864. The iron is Lowmoor, and has been in use nearly ten years. The stay-bolts have become highly crystallized from some cause, and are very brittle, only requiring three blows of an ordinary machinist's hammer to break them. On the other hand, when annealed they are remarkably tough, as shown by the doubled sample. The majority of the broken bolts were found to be along the curve of the shell from a to c, Fig. 6. All of them were broken just inside the shell, and in no case next the fire-box. The fractures seen to have been of slow procedure, beginning at the top of the bolt, gradually working deeper and deeper until the pressure of steam overcame the tenacity of the remaining parts. Unequal contraction and expansion of the parts of the boiler seems in this case to be the only existing cause for a fracture. We cannot, from the data obtained, prove to an absolute certainty the manner in which the combined forces generated by the unequal contraction and expansion of the parts have arrived at their resultant work ; but we can, from these data and from existing circumstances, arrive at what seems to be a fair supposition, and thus at least anticipate the truth. The contraction and expansion in locomotive boilers has a large range between its extremes, and is very variable, both with reference to time and to their component parts. The shell and fire-box do not, perhaps, at any time, contract and expand at the same rate, nor proportionally ; but, on the contrary, owing to the great changes in temperature that take place both in the atmosphere around the shell, and in the fire in the fire-box, their condition is often changed suddenly, and widely from that which they just previously had. This racking tendency produces strains in the different parts, and it is fair to suppose that the continual motion of the two

Jan 1, 1874

By W. S. Ayres

The boiler from which these stay-bolts have just been obtained was that of the locomotive Catasauqtia, Lehigh Valley Railroad, built at the company's shops, South Easton, Pa., in 1864. The iron is Lowmoor, and has been in use nearly ten years. The stay-bolts have become highly crystallized from some cause, and are very brittle, only requiring three blows of an ordinary machinist's hammer to break them. On the other hand, when annealed they are remarkably tough, as shown by the doubled sample. The majority of the broken bolts were found to be along the curve of the shell from a to c, Fig. 6. All of them were broken just inside the shell, and in no case next the fire-box. The fractures seem to have been of slow procedure, beginning at the top of the bolt, gradually working deeper and deeper until the pressure of steam overcame the tenacity of the remaining parts. Unequal contraction and expansion of the parts of the boiler seems in this case to be the only existing cause for a fracture. We cannot, from the data obtained, prove to an absolute certainty the manner in which the combined forces generated by the unequal contraction and expansion of the parts have arrived at their resultant work ; but we can, from these data and from existing circumstances, arrive at what seems to be a fair supposition, and thus at least anticipate the truth. The contraction and expansion in locomotive boilers has a large range between its extremes, and is very variable, both with reference to time and to their component parts. The shell and fire-box do not, perhaps, at any time, contract and expand at the same rate, nor proportionally; but, on the contrary, owing to the great changes in temperature that take place both in the atmosphere around the shell, and in the fire in the fire-box, their condition is often changed suddenly, and widely from that which they just previously had. This racking tendency produces strains in the different parts, and it is fair to suppose that the continual motion of the two

By S. T. Wlodek

The surface and subscale oxidation reactions were followed by means of continuous weight-gain and metallographic techniques over the range 1600" to 2200°F (871° to 1204 °C) for up to 400 hr. Full identification of all scale and subscale reaction products was obtained by electron and X-ray diffraction. At or below 1800°F (982°C) a linear rate of reaction (QL = 46.0 kcal per mole) governed the oxidation process, extending for up to 100 hr at 1600°F (871 "C). During linear oxidation the surface scale consisted of an amorphous SiO2 film overgrown with Cr 2O 3 and NiCr204. This initial linear process was followed, and above 1800°F completely replaced, by two successive parabolic rate laws (Qp = 60 and 57 kcal per mole). This parabolic reaction involved the formation of a complex scale consisting of Cr2 O3 and smaller amounts of NiCr2O4. Parabolic oxidation appeared to coincide with the disruplion of the silica film present during linear oxidation and was followed by subscale (internal) oxidation of crystobalite and NiCr2O4. The balance between the subscale and surface oxidation reactions controls the oxidation of this commercial alloy. The amorphous silica film appears to result in the linear rate and diffusion through Cr2O3 is the more likely rate-limiting step during parabolic oxidation. THE oxidation of a multicomponent composition is a complex phenomenon not presently amenable to a rigorous classical interpretation. Nevertheless, even a qualitative understanding of the scaling and subscale reactions that occur in a commercial composition can illuminate the reactions that limit its high-temperature stability in an oxidizing environment. This study of the oxidation of Hastelloy Alloy X presents the first of a series of studies with the above approach in mind. Hastelloy X exhibits one of the best combinations of strength and oxidation resistance available in a wrought, solution-strengthened, nickel-base alloy. Although during long time exposure some precipitation of M6C and M23C8 carbides as well as a complex Laves phase occurs, the amounts are probably small enough to have no appreciable effect on the chemistry of the matrix. Radavich has identified the oxidation products on Hastelloy X oxidized for 5 min to 10 hr at 1115°F as NiO and the NiCr2O4 spinel. Oxidation for 5 to 15 min at 1500°F produced a scale of spinel, NiO, and a rhombohedra1 phase, probably Cr2Os. Sannier et 2. have reported continuous weight-gain data for Hastelloy X at 1650" and 2010°F and internal-oxidation measurements after 150 hr at 2010°F. In addition, much of the data on binary Ni-Cr alloys recently reviewed by Kubaschewski and okins' and Ignatov and Shamgunova4 as well as studies of binary Ni-Mo alloys5 are also pertinent to the oxidation of this composition. EXPERIMENTAL Continuous weight-gain measurements and metallographic measurements of subscale reactions were the main experimental techniques used in this study. X-ray and electron diffraction backed up by a limited amount of electron-microprobe analysis served to characterize the nature of the scale- and subscale-reaction products. Two heats of commercial sheet of the composition given in Table I and identified as A and B were used in the bulk of this study. Internal-oxidation measurements were made on a third heat of material in the form of a 0.5-in.-diam bar. In order to assure homogeneity, all heats were reannealed 4 hr at 2175°F prior to sample preparation. weight-Gain Measurement. All specimens (1.5 by 0.4 by 0.03 in.) were abraded through 600 paper, electropolished, and lightly etched in an alcohol-10 pct HCl solution. An electrolyte of 150 cu cm H,O, 500 cu cm HsPO4 (85 pct conc), and 3 g CrO3 at a current density of 0.9 amp per sq cm or a solution of 10 pct HaW4 in alcohol used at 4 v and 0.3 amp per sq cm was used for electropolishing. The resultant surface exhibited a finish of 3 ± 1 p rms. Continuous weight-gain tests were made at 1600°, 1700°, 1800°, 1900°, 2000", and 2200°F on auer' type balances capable of recording a total weight change of 110 mg with an accuracy of k0.1 mg. All tests were made in air dried to a dew point of -70°F and metered into the 2-in.-diam reaction

Jan 1, 1964