Search Documents

By J. P. Zannaras

If we assume that testing of the model started at time t1, that time t2 was the instant at which the elastic limit of the material was passed at the points of the maximum stress, and that at time t3 the failure of the model was completed as shown in the typical photograph (Fig. I), then actually the photograph shows the final results of what took place between time t2 and t3. By the principle of similitude all conclusions drawn from the behavior of the model were applicable and valid for actual mine roofs up to the time t2 after time t2 motions and friction came into play during the destruction of the model. The events between t2 and t3 and the photograph itself are not representative of the events expected in an actual mine roof unless corrections imposed by the principle of similitude are made. It can therefore be stated that all conclusions and observations of the author from the photographs are applicable only to his small-scale experiments and not to actual mine roofs. Without investigation of the true stresses or the combined maximum stress induced in the beds it has been assumed by the author that failure occurred solely due to bending stress caused by loading of the beds. (The author states that D was taken to be the theoretical strain given by elementary beam theory.) Fig. 1 shows that the beds were clamped together. This clamping was necessary to prevent slipping of the beds due to the horizontal shear. However, this clamping caused an uncontrolled and undertermined com-pressive stress S at the end of the beds, and this com-pressive stress caused a true tensile stress ?S (? PoiS-son ratio). This true tensile stress combined with the tensile stress produced at the end of the beds due to loading (fixed beam uniformly loaded), and the horizontal shear which is maximum at the end appears to be the most probable maximum stress produced in the beds. It is therefore evident that the author in performing this experiment has introduced stresses in the model not existing or dissimilar to actual mine roofs, and therefore his conclusions may be applicable to his small-scale experiments but inapplicable to actual mine roofs. Louis A. Panek (author's reply)—The discusser's difficulty is related to mechanics of materials rather than similitude. The effect of time did not enter into the tests in any way, being simply excluded from consideration in this study, because all quantitative results entering into the design equations are based on measured (between time t1 and time t2) bending strains that are well below the breaking strain (i.e., in the elastic range) for the model material. Time does not become a significant factor until the rock stress reaches 80 to 90 pct of the breaking stress." The objective of this investigation was not to predict that bolted roof will fail after time t, but was instead to develop a safe roof, that is, roof in which the bending strain is much less than (say less than 50 pct of) the breaking strain. The models tested to failure had no direct bearing on the design equations. Although for some rocks time may influence the magnitude of stress or strain at which fracture occurs, breaking stress or breaking strain values were not employed for any purpose in this investigation. Tests to failure were made only to obtain additional evidence regarding the behavior of the bolted laminae' as evinced by the locations of the cracks. As stated in the last paragraph of the paper, if one wishes to predict the time or stress conditions for which the roof will fail, additional information is required. The reason for clamping the laminae is to make them behave liked clamped beams, which closely approximate the clamped-plate condition of the actual mine roof beds (Ref. 5, p. 1; Ref. 6). The writer has previously demonstrated that the bending stresses induced by centrifugal loading in a clamped model beam are in agreement with those predicted by theory;' hence clamping has no significant effect on the bending ,trains measured during a test. Moreover, actual ,in, roof beds are likewise subject to a clamping effect due to weight of superincumbent strata carried by the pillars or ribs on each side of the opening. It is emphasized that this study was restricted to evaluating only the reinforcing effect produced by the bolts. Procedures employed in the experiments and in the data analysis were such as to deliberately exclude the effects of other factors. The objections offered are therefore invalid,

Jan 1, 1957

By Robert Keeney

Before the outbreak of the war in 1914, the only electric-furnace smelting plant operating on a commercial basis west of the Mississippi River was an electric pig-iron plant in California; rare metal ores were not smelted, concentrates of molybdenum, tungsten, uranium, and vanadium ores being shipped east for reduction. Practically no- chrome ore was being mined, and only comparatively small amounts of manganese ore. Today there are two electric smelting plants in California, one in Washington, one in Iowa, and four in Colorado; two plants are under construction in California, and one in Montana. Ores of manganese, chromium, molybdenum and tungsten are now smelted in the West, and although uranium and vanadium concentrates are still shipped to the East, they will probably be treated in western plants in a short time. The four electric-furnace plants in Colorado are listed in Table 1. TABLE 1.-Electric Smelting Plants in Colorado Capacity, Company, Location Kilowatts Products . Tungsten Products Co Boulder 800 Ferrotungsten, ferromolybdentun. Boulder Tungsten Production Co. . Boulder 400 Ferrotungsten. Ferro Alloy Co Utah Junction 1200 Ferrochrome, ferrotung-sten. Iron Mountain Alloy Co Utah Junction 3000 Ferromanganese. Power for all of these plants is supplied by the Colorado Power Co.

Jan 8, 1918

By Albert J. Phillips

IT is a privilege and a pleasure to deliver this, the Twenty-sixth Annual Institute of Metals Division Lecture. Eleven years ago C. A. Edwards addressed this audience on the subject "Gases in Metals." In spite of this relatively recent presentation, I propose to, present to you some quantitative considerations of industrial significance on the separation of gases from molten metals because recent observations and measurements, presented in the literature, have made it possible to evaluate mathematically the gases or gas-forming elements and to develop an understanding of the mechanism of gas separation that should permit, in many cases, the control of this baffling phenomenon. DEFINITIONS Before becoming involved in the subject it seems desirable, for the sake of clarity, to state certain definitions and axioms: I. We are dealing only with gases that separate from the molten metal either during cooling or in the transition from liquid to solid. Gases injected by the liquid stream and trapped in the solidified metal, or those forced into the solidifying metal from the mold due to either thermal or cher4ical effects are not considered. Neither are we concerned with the separation of gases within the metal after solidification is complete for the data on this subject are at least complete enough to permit the practicing metallurgist to satisfactorily control the phenomenon. 2. Only where there is a decrease in solubility or a change in equilibrium of either a gaseous element or an element that reacts to form a gaseous compound, can there be a separation of a gaseous phase from the liquid or solidifying metal. 3. The amount of gas separating from the liquid during solidification can be computed directly from the amount of the element contained in the liquid when freezing commences less the amount of the element found in the solid either as a separate solid phase or in solid solution. 4. There can be no separation of gas bubbles unless the told pressure of the gases in the liquid meld exceeds atmospheric pressure plus the hydrostatic pressure of ' the liquid metal head. (In addition, pres- sure resulting from surface tension in- creases the total pressure requirement for initial gas separation. Probably the remarkable differences in appearance caused by different gases in the same host metal are influenced greatly by the rate of diffusion of the gas in the liquid metal balancing the decrease in pressure as the gas bubble size increases and the surface tension effect decreases. Thus hydrogen with its high diffusion rate in liquid copper separates in the form of relatively coarse cavities for a given rate of heat extraction.) 5. Gas separation can take place at less than atmospheric pressure in the voids created by the shrinkage from liquid to solid, but since the voids are not caused by the gas the presence of gas in the voids is of importance only where it

Jan 1, 1947

By J. Murray Riddell, Grover J. Holt, Arthur E. Anderson

Out of the depths of each business cycle we emerge with a stimulus for greater efficiency and a realization of progress in industrial technique. The recent years have not been an exception to this rule, and in retrospect we sense that significant advances have been made in mining practices on the Mesabi Range, with emphasis on speed of production and economy of operation. A survey of such changes does not reveal anything that is fundamentally or basically new, but it is apparent that ideas and machines that have found wide application in industry elsewhere, with necessary modifications, are being put to productive use in mining iron ore. Innovations in transporting and conveying ore from the open pits stand out with greatest prominence, so that, in the main, it will be with these features that this paper will treat, in the review of progress made to this date. The late years have witnessed the development of small deposits for open-pit operation, the cleaning up of pits nearing exhaustion, and in two large operations the approach to the limit for haulage by steam locomotives, owing to grades, making it necessary to recover the ore in slopes, track benches and below the power-shovel limit by a milling and scram operation. For several years small standard-type dump trucks have been used in clean-up or scram operations within the pits, but during the season of 1936 the first effort was made to use heavy truck haulage in the transportation of stripping and iron ore. The new units in use today vary from 15 to 20 tons in capacity, and are equipped with powerful gasoline or Diesel engines and supplemented by trailers or wagons on rubber or crawler treads. The Diesel engine finds favor with most operators because of fuel economy. These units develop upward of 125 hp. in the 15-ton trucks. The speed of these trucks varies from 2 miles per hour in Pow gear to 35 in high gear. The transmission affords 12 speeds forward and 3 speeds in reverse.

Jan 1, 1940

By J. Murray Riddell, Arthur E. Anderson, Grover J. Holt

Out of the depths of each business cycle we emerge with a stimulus for greater efficiency and a realization of progress in industrial technique. The recent years have not been an exception to this rule, and in retrospect we sense that significant advances have been made in mining practices on the Mesabi Range, with emphasis on speed of production and economy of operation. A survey of such changes does not reveal anything that is fundamentally or basically new, but it is apparent that ideas and machines that have found wide application in industry elsewhere, with necessary modifications, are being put to productive use in mining iron ore. Innovations in transporting and conveying ore from the open pits stand out with greatest prominence, so that, in the main, it will be with these features that this paper will treat, in the review of progress made to this date. The late years have witnessed the development of small deposits for open-pit operation, the cleaning up of pits nearing exhaustion, and in two large operations the approach to the limit for haulage by steam locomotives, owing to grades, making it necessary to recover the ore in slopes, track benches and below the power-shovel limit by a milling and scram operation. For several years small standard-type dump trucks have been used in clean-up or scram operations within the pits, but during the season of 1936 the first effort was made to use heavy truck haulage in the transportation of stripping and iron ore. The new units in use today vary from 15 to 20 tons in capacity, and are equipped with powerful gasoline or Diesel engines and supplemented by trailers or wagons on rubber or crawler treads. The Diesel engine finds favor with most operators because of fuel economy. These units develop upward of 125 hp. in the 15-ton trucks. The speed of these trucks varies from 2 miles per hour in Pow gear to 35 in high gear. The transmission affords 12 speeds forward and 3 speeds in reverse.

Jan 1, 1940

By C. O. Rison

HIGH explosives, particularly nitroglycerin, have been used in torpedoes for the purpose of shooting oil and gas wells for more than 60 years. The early history of the oil industry in Pennsylvania is not clear as to who actually torpedoed the first well, although in 1865 the Roberts Torpedo Co. procured a patent covering the process. Gunpowder was first used, although nitroglycerin was substituted shortly afterwards. Wells are shot for the purpose of increasing the flow of oil and gas A shot-hole in the producing horizon, with its contributory fissures and fractures, increases the area of and stimulates drainage into the hole. The shot-hole also acts as a collecting basin from which the oil is pumped. As a rule, hard or close-grained sands or limes are shot, other more or less porous and soft formations usually do not require shooting. and might be injured by blasting. Shooting is also resorted to in mechanical trouble such as straightening crooked holes, sidetracking pipe or tools, and for severing frozen strings of casing or drill pipe. Explosives arc also used sometimes to extinguish oil or gas-well fires although that work, which involves unusual conditions and methods, does not properly come within the classification of oil-well shooting. Some Factors to Be Considered in Shooting Wells Although nitroglycerin has been used extensively for more than half a century in shooting oil and gas wells, there is still a great deal of uncertainty as to the proper method of shooting or the amount of explosive required to produce best results in a particular formation. The possibility of shooting unproductive or cavey formations above or below the productive horizons, shooting into lower water, destroying casing seats, and the splitting or collapsing of casing strings, are factors that require consideration. The engineering departments of a number of the larger oil companies are making a study of methods of shooting, and the amounts of liquid nitroglycerin or other explosives required in shooting various productive

Jan 1, 1929

On the following pages are abstracts of papers published by the Institute during the year 1934 as TECHNICAL PWLICATIONB, CONTRIBUTIONS, m bound volumes and in MINING AND METALLURGY. For abstracts of papers that appear In bound volumes in 1934 but that were published as TECHNICAL PWLICATIONS m 1932 or 1933, see the TRANSACTIONS for 1932 and the YEAR BOOK dated January, 1934. Many of the TECHNICAL PWLICATIONS have been reprinted In bound volumes Information regarding this disposition, and number of pages in each paper, may be found m the list beginning on page 92 Volume numbers are given as listed at the beginning of the index, page 99 The abstracts are grouped as follows:

Jan 1, 1935

The objective of the mission was basically to study the utilization of engineers and engineering technicians and their interrelationship in the Soviet Union. Beginning with their graduation from the engineering institutes and technicums, we hoped to learn how the graduates started out in industry, what their training on the job was, what sort of work they did, and how they worked themselves up within their profession. However, it turned out that, as our host was the Ministry of Higher and Secondary Education, most of our visits were to educational establishments. Our itinerary covered Moscow, Leningrad, Kharkov, Rostov, Baku, and Tashkent, with a side trip to Samarkand. In all, we visited 13 technical institutes, three technicums, and five industrial plants or enterprises, as they are called there. Our trip was one of only four weeks. Our observations were limited by the few cities and enterprises we were permitted to visit. Nevertheless, we did come back with some definite impressions and conclusions which we feel should be of interest to engineers, educators, and those concerned with the relative economic and technical power of the USSR and the U.S.

Jan 9, 1960

DEVELOPMENT of a chemical process for the extraction of pure metals from mill concentrates or metal scrap has progressed beyond the pilot plant stage and may prove an important adjunct to present smelting and refining methods if initial commercial operations prove economically successful. Developed by the Chemical Construction Corp., the new process involves the treatment of oxide and sulphide ore concentrates by chemical methods, instead of the usual smelting and refining techniques. Several of the many applications are now scheduled for commercial use. Refiners using the new process will prepare ore concentrates by standard flotation methods, introduce the concentrate as a slurry into an autoclave along with water and an acid or ammonia. From the resulting leach solution, recovery of individual metals is made by use of suitable reducing agents. By varying conditions during treatment, different metals in the ore are produced separately as pure powders, which may be pressed into forms ready to market, or in the case of copper, extruded as rods or pipe. The reagents are generally recovered. By manipulating the variables during reduction, selective separation of nickel, and/or cobalt, and/or copper can be made simultaneously. The separation is a continuous operation. Low metal prices are not immediately in view because of the tremendous demand at this time. However, reduced metallurgical treatment costs will allow economical mining of orebodies with lower metal content, permitting increased production to meet demand. Although the practical horizon for use of the new process appears to be limitless, one factor may enter into its employment. Just how low grade a concentrate can be economically used is unknown. In addition, for present practical considerations, only metal below zinc in the electromotive series may be processed. Each commercial application requires specific technique adaptation and pilot-plant data for engineering design. A nickel-cobalt-copper process has been researched and piloted in collaboration with Sherritt Gordon Mines, Ltd., for the firm's Lynn Lake properties. In addition, processes were tailored for cobalt concentrates of Howe Sound Mining Co., and National Lead Co., in view of the urgent need for this specific metal. Major General William N. Porter, president of Chemical Construction, says of the new process, "piloting experience has shown that production cost, from ore concentrates to pure metals should be considerably below current costs." Other savings may be realized by cutting transportation and personnel costs, and by reducing the time lag between mining and pure metal from months to a matter of hours. First commercial use of the process will start sometime this summer. Chemico is slated to finish building a $2.5 million cobalt refinery for Howe Sound Mining near Salt Lake City. The plant is expected to raise world cobalt production by 40 pct. The plant will process 35 tons of 20 pct cobalt concentrates from Howe Sound's Blackbird mine near Cobalt, Idaho, daily. Yearly production is expected to reach 2000 tons of pure metal, about one half of U. S. consumption in 1950. Steps in the Howe Sound application of the process are: 1. Acid oxidation leach. 2. Filtration (residues thrown away are insoluble compounds-gangue, iron, arsenic). 3. Cementation (for Cu removal because Cu content is too low for recovery). 4. Reduction from ammoniacal solution. 5. Separation of Co and Ni as mixed metals (95 pct Co and 5 pct Ni). 6. Recovery of ammonium sulphate. Under construction at the Fredericktown, Mo., mine of National Lead is a $5 million refinery sched- [ ]

Jan 1, 1952

W. ROWLAND Cox,* New York, N. Y. (written discussion?).-The process described by Mr. Malcolmson undoubtedly represents a great stride toward conservation of our natural resources. Without discussing the subject from an economic standpoint, I wish further to emphasize the fundamental principles of the Smith process in order that its economic value may be fully appreciated. The process is essentially a means of producing an ideal fuel, as regards its combustion qualities, by the removal of the so-called volatile matter from the coal, in the form of byproducts, which have value for other purposes far in excess of their fuel value. In other words, coals which contain. large amounts of gas, tar, and ammonia, and are not suitable for domestic or industrial fuel, or for treatment in byproduct coke ovens or gas retorts; because they possess poor coking qualities, can he prepared for commercial use by the. Smith process with a very high degree of efficiency. Much work has been done along this line, both in this country and in Europe, in developing a means of preparing coal, as the economic advantages have long been recognized. To the best of my knowledge, the Smith process is the only one that has proved its commercial adaptability. Distillation of coal at 900° to 1000° F. (480° to 540° C.) yields a large amount of tar and oils. The residue of the distillation, however, is a very friable semi-coke, wholly unsuitable for use as a fuel, unless it can be charged directly into a byproduct gas producer. The problem which confronted the inventor was then to convert this carbon residue into a commercial product, and it is in this step that the Smith process has overcome the obstacles which prevented a number of other methods from becoming commercially practicable.

Jan 10, 1918

By H. Y. Bassett

THIS paper attempts to show the various major operations used in nonferrous tube mills and does not necessarily represent the current practices at the two plants of the Wolverine Tube Div., of Calumet and Hecla Consolidated Copper Co. Inc. The operations now utilized in the production of tubing are quite varied and show the continual interest and advance metallurgically and mechanically to produce the best quality at the lowest cost. Naturally, any advance or lowering of cost is dependent on large production runs, which mean longer machine running time with maximum worker productivity. Standardization of tube sizes and elimination of unnecessary alloys are therefore very necessary, otherwise the development of costly new production machines would be of little benefit to the consumer as a whole. It should be noted that in such a short presentation it is impossible to describe in any detail the major operations. The short descriptions, it is hoped, will enable all who are interested to obtain a general idea of present, day practices in the copper tube producing field. Fig. I is a flowchart or sequence of operations showing the steps usually employed in tube production. RAW MATERIALS Quality starts with the raw material, and it is absolutely necessary that raw material be controlled and held to rigid specifications. Little need be said, however, regarding the raw materials for the casting of bars or billets, as the material always is purchased and checked against the various governing A.S.T.M. specifications. CASTING Casting, as is indicated in Fig. I, is quite varied and for convenience can be classified into two groups: The casting of solid billets, and the casting of hollow tubes, each of which is the base for subsequent operations. In the melting of the raw materials various types of furnaces are used, and the selection of any one is dependent on many factors outside the scope of this paper. However, as of general interest, a short description will be made of each. Induction Furnace (Low Frequency) This is popular in the melting of copper-base alloys, Fig. 2. In the induction furnace the principle of an inefficient transformer is used for the production of the necessary melting heat. The primary coil is.arranged around a transformer core made of high permeability silicon steel sheet. The secondary circuit is through a melting channel around the primary coil and opens into a hearth which contains the main charge. The heat is generated only in the melting channel, but because of the stirring action there is a constant flow of metal around the channel, which when mixing with the charge causes very rapid melting. The volatilization losses are very low as the furnace atmosphere above the charge is heated only by the heat from the melting metal. The stirring action, however, makes the use of any slag cover difficult. Such furnaces- must be started with molten

Jan 1, 1951

AT the fall meeting of the Iron and Steel Division, Oct. 4, 1934, in New York, a symposium was held on Slag Control in the Making of Iron and Steel. The chairman was J. H. Nead and the vice chairman, G. B. Waterhouse. The latter presided at both morning and afternoon sessions. The papers and discussions were presented in the order in which they appear on the following pages. To meet space requirements, much of this material has been considerably condensed. CONTENTS [ ]

Jan 1, 1935

By Dean Goodermote, Carla S. Stone

I Introduction Coal fuels China. Roughly 70 percent of all commercial energy demand is supplied by domestic coal production and with the recent Chinese opening to the West, the Chinese Coal Industry may figure prominently in the export market as well. Because of the importance of China's coal industry to the future of China and the Pacific Rim energy balance, this paper reviews the industry and offers some cautious projections for its outlook. II Energy's Position in the Current Political and Economic Climate Traditionally, Chinese society has been dominated by the policies of its most important government leaders. Deng Xiaoping, Vice Chairman of the Communist Party is the current leader of China. Deng and his proteges are pragmatists. Although China's government structure is based on Marxist/Leninist tradition, Deng and his followers are promoting experiments with market economics and expanded relationships with Western Countries, which have encouraged foreign investment in China. Energy companies represent just one type of industry that is interested in helping the Chinese to develop their abundant natural resources. Although China's leadership is committed to a program of economic modernization, that program currently is experiencing what the Chinese government terms "readjustment". Readjustment cuts back in imports due to deficient foreign exchange and deemphasizes heavy industry, while it encourages agricultural and consumer goods output and, most imporant, energy production. Increased Chinese coal and oil production is essential both to fuel industry and, equally important, to provide foreign exchange. If sufficient energy production is not forthcoming, then economic growth will be severely retarded. China's 1979 per capita GNP of $260 is only slightly better than the weighted average achieved by low income countries of $230. (1) Delays in growth could lead to social unrest, threatening the position of the current leadership. Since there is no institutionalized mechanism for leadership succession and policy continuation, it is reasonable to assume that leadership changes could result in energy policy changes. III Energy Consumption Energy production is important to China's future economic health as highlighted by the World Bank. If China's economy grows rapidly, 5 percent to 6 percent during this decade, the Bank noted, a significant energy shortfall could occur as early as 1985. This state of affairs contrasts sharply with China's current position as a net hydrocarbon exporter. (2) To assure a healthy economic future, China's leadership is attempting to reduce its rate of increase in energy demand through conservation as well as to boost energy output. A massive conservation promotion program has been underway since 1979 and there is much room for improvement. China's industrial sector is only about half as energy efficient as is U.S. industry. (3) During the last two decades, each percent of increase in GNP has been accompanied by a 1.8 percent of increase in energy consumption. (4) This compares rather poorly with the United States where a less than one-to-one relationship exists. IV Energy Supply The short term prospects for oil production are uncertain. Production increases were rapid in the 1960's and early 1970's, averaging 20 percent annually, but most of this increase came from one field, Daquing. Now that Daquing's production has peaked and the offshore potential has yet to be developed, petroleum production has maintained a plateau of 2.1 million b/d, at least temporarily, of which approximately 15 percent is exported. (5) Output

Jan 1, 1982

By Robert S. Schecter, Mark P. Walsh, Michael J. Humenick

In recent years in situ leach mining has emerged as a viable technology for the recovery of uranium from strata in South Texas which contain relatively low concentrations of uranium ore. Because the ore bodies lie within ground-water aquifers, a significant determinant in the economics is the requirement that such aquifers be protected from contamination. Since ammonia is one of the constituents of the leach solutions now being field tested, one environmental problem to be resolved is the removal of ammonia at the end of mining. A second related question is the fate of the ammonia which is not removed by the restoration procedure. This paper considers the displacement and migration of ammonium in a flowing electrolyte with concomitant ion exchange. The ion exchange is an important feature since, during the solution mining phase, ammonium saturates the mineral exchange sites and must be removed from these sites. A mathematical model is used to simulate this process and the model is tested against the results of laborator.y experiments. It is found that the simulations are adequate if an appropriate selection of parameters is made. The model is then used to investigate the effect of cation composition and concentration of the restoration medium as well as dispersion on the overall effectiveness of the process. It is concluded that increasing the concentration of monovalent ions in a solution containing a mixture of both monovalent and divalent ions decreases the adsorption selectivity of the divalent ions with respect to all monovalent ions including ammonium. Thus increasing the ionic concentration of a restoration fluid by increasing the concentration of a nonselectively adsorbed (with respect to ammonium) ion may have a very limited benefit.

Jan 1, 1979

By Baxter C. Madden

Stress corrosion is defined and certain examples are illustrated. A number of test methods, to determine the resistance of materials to stress corrosion, are being developed at Wright Field. The criterion as to the validity of a method is stated. Three types of specimens and the method of stressing each type are described. Five different corrosive conditions are set forth. The results of tests to date, although too few for any general conclusions to be arrived at, are presented. The program for the continuation of the investigation is indicated. A bibliography is included. The development of the method of loading a cantilever-type specimen, so that a nearly constant stress at a large deflection may be realized, is presented as Appendix I.

Jan 1, 1945

By William G. Pariseau, H. Douglas Dahl

Recent subsidence legislation indicates that mining engineers would be welt advised to be able to predict and control surface damage caused by mine subsidence. To date, such an ability is practically nonexistent. Model analysis is suggested as one of the alternative paths available which might yield fruitful results. Similitude requirements developed for a self-loaded body in static or quasi-static equilibrium indicate that complete similitude without centrifuging is an impracticability. However, a pilot experimental study which used a simplifying assumption to correctly model mine subsidence has produced results in qualitative agreement with field observations. The purpose of this paper is to present a discussion of the various approaches that can be taken in the study of mine subsidence phenomena. Particular attention is focused upon the rational selection and use of laboratory models. Broadly interpreted, mine subsidence is the deformation of the rock mass enclosing a mine. Depending upon a number of factors, the movement of the subsiding rock mass may disrupt gas and water lines or other buried utilities, damage surface structures such as buildings and bridges, dislocate streams, roads, and rail lines, aggravate acid mine drainage and fire problems, and generally mar the landscape. It is clearly a problem that no mine manager can safely ignore. It is also a problem that will grow with the general population increase. In the following discussion, a summary review of past and present approaches to subsidence studies is given. The possibilities of duplicating subsidence phenomena in laboratory models are examined, and an analysis of a particular type of model is presented. Some preliminary results obtained from a model of the particular type analyzed are then discussed. REVIEW OF PREVIOUS WORK Historically, subsidence investigations have been empirical studies in the field and laboratory or theoretical analyses of mathematically idealized media. Empirical and theoretical work in the United States has generally lagged behind investigations abroad. In the United States, field studies are mostly pre-World War 11. These are summarized in the Mining Engineer's Handbook. ' Field studies in Europe are more recent and more extensive. Those made in Great Britain are summarized in the Subsidence Engineers Handbook2 and represent observations made at 157 different collieries. Such studies by themselves are of limited usefulness as are all empirical studies. One can never be certain that conditions at one mine will be similar enough to those at another to warrant the drawing of like conclusions. European subsidence formulas rely heavily upon the "angle of draw" and "critical area" concepts. The angle of draw is defined as the angle between a vertical line through the face, and another line extending from the face to the surface at the point where movement is zero. The critical area is defined in relation to the least extraction necessary to produce maximum subsidence. Fig. 1 illustrates the angle of draw and critical area concepts. First and second "limits of influence" are also shown. The angle of draw and associated critical area concept are obviously not well defined, being dependent upon the accuracy of the surface survey. In Great Britain, the angle of draw has increased through the years from about 26 to 35°. In the United States, zero and negative angles of draw have been reported. In the authors' opinion, these purely geometrical concepts represent an oversimplification of subsidence phenomena and their use, in the United States at least, should be discouraged. Empirical observations of laboratory models containing layers of earth, sand, clay, and plaster were made by Fayol (cited by Peele) as early as 1885. An outgrowth of his work was the "dome theory," a verbal description of what is assumed to occur in subsiding rock masses. The dome theory has since fallen into disrepute. Theoretical analyses worthy of the name treat a subsiding rock mass as a deformable body. In these analyses, the actual rock mass is replaced by an idealized material that deforms according to a simple stress-strain relationship. The stress equations of equilibrium expressing the Newtonian laws of mechanical action and the geometry of strain furnish additional equations that must be satisfied. A loading criterion-generally understood, and in some cases stated explicitly-completes the theory.

Jan 1, 1969

Jan 1, 1957

By W. B. Finkeldey, C. H. Mathewson, C. S. Trewin

This paper was prepared upon request as a contribution to a symposium covering the manufacture, properties, and uses of the important non-ferraus metals. In approaching a subject as broad as this, there is a natural desire to build up a comprehensive and finished production which shall constitute a dependable source of information on all questions properly belonging to this branch of metal technology. There are, however, a number of circumstances, apart from the mere routine of labor and thought involved, which operate rather effectively against the possibility of completing such .an ambitious program at the present time. First of all, as far as any public record of results is concerned, the commercial rolling, drawing, and forming of zinc with relation to changes of structure and properties—and this we consider to constitute the clement~ of metal technology—might as well be an unpractised art. We have never seen a published photomicrograph showing the structural characteristics of either hard or soft sheet or strip, although the structure of castings has been frequently described, and other coarse-grained structures resulting from hard-hammering and annealing have been reproduced. Thus, an author in this field must proceed to his task without much assistance from the literature, and the outcome can represent only a personal estimate of principles, facts, or findings, and not a summary or survey of progress in the entire field as determined by varied experience, practice, and settled opinion.

Jan 1, 1921

By Henry S. Rawdon

The structure of wrought iron as usually described by metallographists and workers in metal in general is that of a fairly pure iron. Impurities, if present, are usually considered as being in solid solution in the crystals of the ferrite matrix or as forming part of the ever present "slag streaks." Attention is herein directed to one type of these dissolved impurities; to the detection of such impurities, particularly in low-grade irons, and to their possible influence on the physical properties of the metal. The attention of the Bureau of Standards was first directed to wrought iron of the peculiar and unusual characteristics to be described later, in material which had failed in service and was submitted for test. The examination was extended to other grades of wrought iron, to see whether such features are of common occurrence in this class of material. MICROSTRUCTURE OF WROUGHT IRON Usual Structure The general microstructure of wrought iron is so well known that a detailed description of it here is needless. There is shown in Fig. 2 the structure of a sample of Swedish iron which illustrates well the matrix of ferrite crystals in which are embedded the slag threads so characteristic of the puddling process and the subsequent working of the material. The usual commercial product contains varying amounts of the impurities commonly associated with iron and steel, i,e,, manganese, phosphorus, silicon, and sulphur together with small amounts of carbon. Of these, the larger part of the phosphorus and some of the silicon present are held in solid solution in the ferrite while most of the remaining impurities, other than carbon, exist in the in closures of slag. Aside from the discontinuities introduced by the slag streaks the ferrite matrix has the microstructure and appearance of a pure metal. No definite orientation of the various crystals or grains is apparent; deep etching of the specimens reveals no intracrystalline features (i.e., within the grains) other than those noted in " pure " metals in general (etching pits).

Jan 1, 1918

By F. G. Smith

A FEW years ago, the writer encountered a, problem that, at first, seemed to be due to peculiar conditions affecting grain growth. Large cups made from heavy metal failed in the first drawing operation in the process of making seamless tubes. The metal, as cast, appeared to be sound and strong; it rolled successfully and withstood the first cupping operation, but on the first draw it failed, with a crystalline fracture. The failure appeared in the slightly worked part of the bottom of the cup, and microscopic examination revealed exceptionally large grains. Knowing the general conditions governing recrystallization of brass, which were later published by Matthewson and Phillips, an investigation was outlined with the idea of including various conditions under which new grains might form, and which would include the effect that a previous anneal might have upon the anneal following. These conditions were produced by annealing specimens of brass at five different temperatures, indenting them with a 10-inn. ball under four different pressures, and then reannealing at each of the five temperatures five specimens each of which had been annealed at one of the five temperatures.

Jan 8, 1919