Search Documents

By R. A. Nadler and

Specimens of Ti-155A (Ti-5Al-1.3Fe-1.3Cr-1.2Mo), Ti-6Al-4V and Ti-4Al-3Mo-1V were hydrogenated, aged to high strength levels, and subjected to notched stress-rupture tests and tensile tests at two strain rates. Both Ti-6Al-4V and Ti-155A were relatively unaffected by hydrogen in amounts exceeding those found in commercially -produced material. Inconsistencies in the data and a relatively low initial level of ductility prevented an accurate determination of the hydrogen tolerance for aged Ti-4Al-3Mo-1V, but there was no evidence that this alloy was any more susceptible to hydrogen embrittlement than Ti-155A and Ti-6A1-4V. THE metallurgical literature has been considerably enriched in the past five years by the publication of the results of many investigations which were concerned with the effects of hydrogen on titanium and its alloys. Although it is not the authors' intention to provide a complete literature survey of this vast field, it is worthwhile to summarize briefly some of the important factors which influence the embrittling phenomenon in a - B alloys. Some of the influencing factors are those of strain rate, temperature, and composition. Hydrogen embrittlement in a - B titanium alloys is now believed to be a strain-induced phenomenon, and whether or not embrittlement occurs at high hydrogen levels depends largely upon whether sufficient time is available for hydride precipitation. This condition is fulfilled by tensile testing at very slow strain rates or by rupture testing smooth or, preferably, notched specimens over relatively long periods. Conveniently, maximum embrittlement occurs at or near room temperature. The presence B - stabilizing elements, in amounts sufficiently small to prevent an all -B or nearly all -P condition, promotes hydrogen embrittlement and this tendency is believed to be related to the amount of a - B interfacial area present. Aluminum, by increasing the solubility of hydrogen in A titanium, greatly reduces the danger of hydrogen embrittlement, while oxygen has been shown to have detrimental effects.' The preceding discussion is based on experimental work performed on annealed a - P alloys. This early work has shown that annealed Ti-6A1-4V and Ti-155A are relatively insensitive to the embrittling effects of hydrogen.' Although no work has been reported on annealed Ti-4A1-3Mo-lV, the alloy would be expected to exhibit somewhat the same insensitiv-ity as Ti-155A. In sharp contrast to the voluminous literature on annealed titanium alloys is the paucity of reported investigations on materials receiving commercial heat-treatment cycles. To date, the most notable contributions in this field have arisen from two separate investigations on Ti-3Mn-1Fe-1Cr-1V-lMo, the so-called 3Mn comple~. These investigations

Jan 1, 1961

By Herbert Clark Hoover, Lou Henry Hoover

DIFFERENT methods of parting gold from silver, and, on the other hand, silver from gold, were discussed in the last book; also the separation of copper from the latter and further, of lead from gold as well as from silver ; and, lastly, the methods for refining the two precious metals. Now I will speak of the methods by which silver must be separated from copper, and likewise from iron.1 The officina, or the building necessary for the purposes and use of those who separate silver from copper, is constructed in this manner. First, four long walls are built, of which the first, which is parallel with the bank of a stream, and the second, are both two hundred and sixty-four feet long. The second, however, stops at one hundred and fifty-one feet, and after, as it were, a break for a length of twenty-four feet, it continues again until it is of a length equal to the first wall. The third wall is one hundred and twenty feet long, starting at a point opposite the sixty-seventh foot of the other walls, and reaching to their one hundred and eighty-sixth foot.

Jan 1, 1950

By Bruno Nordberg

THE high cost of coal in Butte and the development of large amounts of cheap electric power from the Missouri river caused the Anaconda Copper Mining Co. in 1908 to make an investigation as to the possibility of adapting this cheap electric power for the operation of their many large hoisting plants. At this time electric power had already been adopted for practically all other power purposes around the mines, such as pumping, compressing air, etc. The map (Fig. 1) shows the location of the mines of the Butte mining district. These mines are located within a circle of approximately a 1-mile

Jan 9, 1913

By C. C. Furnas

IT is well known that particles of different sizes are not distributed evenly throughout the average charge in an iron blast furnace. Just how great the disparity in particle size in different parts of a single plane in a furnace may be is indicated by the results of some recent investigations1 conducted by the Bureau of Mines on a furnace operating on Lake ores. The wide variations found in gas velocity, gas composition, and temperature from the periphery to the center of the upper charge column were caused by the great variation in particle size of the raw materials used and were also greatly influenced by the methods of charging. This paper summarizes the results of an investigation of the influence of different methods of charging and of the treatment of raw materials upon the size distribution of the solid particles in the blast furnace. A more complete report will appear later as a Bureau of Mines technical paper.

Jan 1, 1929

By Walter Harvey Weed

The Republic of Mexico is traversed by many mountain ranges, and presents a great diversity of climates, soils and geographical features, yet its grander geographic provinces are few and peculiarly well defined. The Gulf plain, the Cen tral plateau, the Sierra Madre, and the lowland or Tierra Cali ente of the western coast are the main features of the geogra phy of the Republic, and in the northern half these provinces are particularly well defined. The Sierra Madre separates the Republic into eastern and western parts, and from the City of Mexico north to the Texas line presents an almost impassable barrier to east and west travel. On the north, the first wagon road pass from east to west is at El Paso del Norte, the site of the Texan city of El Paso. Southward for many hundreds of miles the Sierra Madre, traversed by well-worn trails, over which all travel from the west coast to the interior must pass, is a stupendous barrier to social and commercial intercourse. The Sierra Madre is commonly described as a range or con geries of mountain ranges. In fact, it is, in Chihuahua at least, a great plateau, fringed by mountains on the east, trenched by deep canons in its center, and bordered by a wild and rugged complex of mountains carved out of the plateau on the west. Professional duties took me across this region from Parral westward to the Gulf of California via Guadalupe y Calvo. As it includes some of the great ore-deposits of Mexico, and its geological features have never, so far as I am aware, been described, I have prepared a diagrammatic section made from my observations on a horseback trip across the Sierra, and added such notes as seem to be of general interest.

Jan 1, 1902

By Norman Braly

THE following is not offered as an extended paper on the subject of shaft sinking, but more as a description of the present practice of shaft sinking in the Butte district. The Anaconda company is sinking at present the following shafts: Badger State, Moose, Mountain Consolidated, Mountain View, Pennsyl-ania and Tropic. At the High Ore and Leonard mines the shafts are being deepened by sinking two compartments and will subsequently be enlarged to the full working size by raising alongside the compartments which are now being sunk. The following other companies are also sinking shafts: Butte-Alex Scott, Butte and Zenith City, Boston and Corbin, North Butte Mining Co. (at the Granite Mountain shaft), East Butte Co. (at the Pittsmont shaft), and the Rainbow Lode Development Co. Shaft Timbering. The shafts of the Butte district, generally speaking, are of three compartments arranged in a straight line, and the pump compartment is usually arranged for the use of an auxiliary hoisting cage, as well as for carrying pipe lines and electric wires. The Rainbow shaft is practically square, and of three compartments. The length of the shafts outside of timber will vary from 17 to 22 ft., and the width from 6 ft. 6 in. to 7 ft. Fir timber is used in all shaft work. This may be obtained from the Coast, when it is known as Coast fir, or from Idaho or Montana, when it is known as native fir. The native fir seems to be the tougher wood, but it is hard to obtain clear lumber in the lengths and sizes necessary for shaft work. Some of the shaft timber of the Anaconda company has been treated with creosote as a preservative, but this practice has not come into general use, as the ground of the camp is so heavy that the timbers usually crush before they rot. The size of timber most .used for shaft work is 12 by 12 in., while 10 by 12 in., 10 by 14 in. and 12 by 14 in. are used for some of the special pieces around the shaft. The new Leonard shaft is timbered with 14 by 14 in. wall plates throughout.

Jan 8, 1913

By H. M. St. John

MAINTAINING a satisfactory structure in brass and bronze castings has always been a foundry problem of great practical importance. While metallurgists and scientific investigators have not entirely ignored this matter, it has received less of their attention than has been given to iron, steel and the wrought copper and aluminum alloys. Investigation in this field has probably been discouraged to some extent by the complicated nature of the alloys involved. Hundreds of alloys are in more or less common use, most of them containing copper, zinc, lead and tin in-widely varying proportions. They also contain appreciable percentages of iron and antimony as impurities, and often phosphorus, which has been added as a deoxidizer and fluidifier. Small amounts of sulfur are usually present. It is not uncommon to find nickel, sometimes in rather substantial quantities. Traces of other metals are frequently present. So complicated and variable a mixture obviously offers difficulties in. any investigation of the various factors that influence the structure and other properties of the casting.

Jan 1, 1930

By F. W. Luersson

High carbon, low phosphorus steel can now be made from pig iron containing 0.7 pct P or more, in a commercial sized open hearth furnace. No external heat is required for refining, and steel produced is identical with basic open hearth steel. THE classical Thomas process, which requires liquid pig iron containing over 11/2 pct P, yields a product relatively high in phosphorzs and nitrogen. Unless large quantities of recarburizers are added to the refined steel, the product is low in carbon content. Thus, the Thomas process is not well suited to American raw materials, and its product is often not acceptable according to the standards set by American industry. The shortcomings of the Thomas process have long been recognized; with the advent of low cost oxygen, studies were initiated to develop pneumatic processes which would conceivably overcome the inherent objections to Thomas steelmaking. Several such modified basic pneumatic processes have been tested experimentally in commercial trials during the past decade. Probably the most widely publicized of these developments has been the oxygen converter process as practiced in Austrial,2 and in Canada.8 n this process, oxygen is substituted for air and introduced above the liquid bath in order to increase the heat available to the metallurgical system. This avoids the need for high phosphorus raw materials and gives a product low in nitrogen. In this process, the phosphorus content in the final product depends, to a considerable extent, on the total amount of that element in the burden. The rotary furnace4 which is now in commercial operation at Domnarvet Steelworks, Sweden, is producing low phosphorus steel from iron containing 1.8 to 2 pct P. One or more early slags are removed and by this means high carbon steels of open hearth quality can be produced. At this stage of development there is some question as to the applicability of the rotary process to large heats. Another development has been the use of oxygen in combination with either steam6 or carbon dioxide yn the basic bessemer, thus avoiding the introduction of nitrogen gas into the refining system and giving a product relatively low in nitrogen content. A double slag process has been used in Europe7 in conjunction with a regular Thomas converter, by means of which it is possible to obtain a phosphorus content in the product approaching that obtained in basic open hearth steels. The Turbo-Hearth process:' which uses the side blowing principle so as to produce low nitrogen steel from normal American pig irons, has been developed experimentally in this country. A process fitted to U. S. raw materials All of the preceding processes, with the exception of the rotary furnace, suffer from the common shortcoming that they cannot be adapted to the production of high-carbon, low-phosphorus steels unless large proportions of recarburizers are added. In 1947, a program was initiated by the Inland Steel Company1' to study an oxygen steelmaking process specifically designed to utilize the full range of phosphorus analyses encountered in American pig irons and to give finai products with phosphorus and nitrogen contents comparable to steel produced by the basic open hearth process. Some of the objectives of the proposed process are: 1) the process should be able to accommodate molten pig iron conta;rl;rrg up to 1 pct P., 2) sne process should be subject to close control of carbon analysis, 3) the process should be capable of producing high carbon

Jan 1, 1958

By R. W. Raymond

THE absence of a convenient glossary of terns connected with mining and metallurgy has long been felt by the general public. It is to meet this want, not to furnish a technical manual for experts, that the following glossary has been prepared. It originated in an attempt on my part to revise for publication the manuscript of a compilation prepared from the appendix of Yale's work on Mining Titles and one or two other sources, to serve as an appendix to a new work on mining law, about to be published by Mr. H. N. Copp, of Washington, D. C. This revision soon assumed, contrary to my original intention, the proportions of a reconstruction ; and with the consent of Mr. Copp, and for the purpose of receiving from my fellow-members valuable aid, I presented my still incomplete work as a paper at the Lake Superior meeting of the Institute, inviting from any quarter suggestions of new terms or better definitions to be incorporated in the glossary before its final publication. This invitation was so widely and generously responded to, that I cannot undertake to make in this place' individual acknowledgments to those members of the Institute, and professional colleagues outside of it, who hays favored me with ' assistance and advice. The labor bestowed upon this paper since its presentation, at the Lake Superior meeting has considerably exceeded that of its first preparation, as

Jan 1, 1881

By L. K. Jetter, C. J. McHargue

DEVELOPMENT of preferred orientation in uranium is of interest because of the strongly anisotropic properties of the orthorhombic crystal structure. Harris&apos; reported inverse pole figures for rolled uranium rods which showed <010> and <410>* to be parallel to the rolling direction after On 0.19-in. spherical X-ray diffraction specimens taken from the center of the middle section of each rod, pole distribution data were obtained by the spectrometric method described previously.4 The specimen was rotated rapidly about the axis coinciding with the rod axis in order that a large number of grains could be scanned and was rotated slowly about an axis perpendicular to the rod axis. The variation in the diffracted X-ray intensity was recorded as a function of the latter motion (angle 4). Fiber-axis distribution charts (inverse pole figures) were prepared by the method described by Setter, McHargue, and Williams." After having been corrected for background radiation, the pole distribution data (I vs ?) were normalized. A normalizing factor for each plane has been shown to be Iranaom = f I sin 4 ? 4 and was obtained by graphical integration from the data for that plane plotted as I sin ? vs ?. The axis-distribution charts deduced from the normalized pole densities are shown in Figs. 1 to 3. On these charts, the contours indicate angular positions of equal normalized axis density,

Jan 1, 1958

On the following pages are abstracts of papers published by the Institute during the year 1936 as TECHNICAL PUBLICATIONS and CONTRIBUTIONS, papers in bound volumes appearing for the first time, and papers in MINING AND METALLURGY For abstracts of papers that appeared in bound volumes in 1936 but that were published as TECHNICAL PUBLICATIONS in 1935, see the YEAR BOOK dated January 1936.

Jan 1, 1937

By J. W. Leonard, J. C. Anderson, C. T. Holland

PREPARATION CONTROL IN UNDERGROUND MINING Selective Mining According to district Depending upon the particular geographic loca- tion or seam characteristics, modern raw coal preparation practices can be used to obtain improved product quality and uniformity. Nevertheless, certain coal markets may require only marginal quality while others may require very high quality, and these objectives may be sought by commencing the preparation of coal underground at the "working face." Under- ground preparation involves choosing those portions of the seam which can be cleaned to satisfy predetermined market requirements involving ( 1 ) maintenance of uniformity in chemical quality, (2) elimination of removable impurities, (3) control of sizes and size ratios, and (4) control of moisture. The methods employed to attain these objectives vary widely with the (1 ) seam under development, (2) mining equipment available, and (3) changing trends in the consuming markets. When a mining property is opened and development progresses from one section to another, the (1) petrography of the coal in the seam does not remain uniform, (2) character of roof and floor are subject to change, and (3) character and prevalence of mineral impurities are subject to considerable variation. The quality of coal shipped to market from any mine depends upon intelligent foresight, planning, execution, and supervision. Mining becomes a highly technical art. The quality of coal as determined by chemical and petrographic analysis is without question one of the most important considerations in the development and life of any coal-mining property. Variations in such proper- ties as volatile matter, ash, sulfur, Btu content, and petrography are of considerable interest, and to a limited extent so are such properties as phosphorous content, free swelling index, plasticity, hardness, pressure formation during coking, and ash composition. The maximum and minimum specifications of these characteristics as established by competitive market conditions place definite limits on the marketability of a coal.

Jan 1, 1979

By K. D. Jacob, H. L. Marshall, D. S. Reynolds

All types of commercial phosphate rock produced throughout the world contain fluorine in quantities ranging from approximately 0.4 to 1.3 per cent in the Curacao and Christmas Island phosphates to 3.1 to 4.2 per cent in the phosphates of the United States and North Africa1. For a given type of rock, the fluorine content is usually roughly proportional to the phosphorus content. Significance of Fluorine in Phosphate Rock On the basis of chemical and X-ray diffraction studies, Hendricks and co-workers2 concluded that fluorapatite, Cal10F2(PO4)6, is the essential phosphatic constituent of the commercial types of domestic phosphate rock. On the other hand, Bredig and co-workers3 have recently advanced the opinion, also based on X-ray diffraction studies, that the mineral phosphates usually contain carbon dioxide in the apatite lattice, and that the phosphate rocks of the United States are really fluorcarbonate apatites. However, the domestic types of phosphate rock do not seem to differ greatly from coarsely crystalline fluorapatite in their behavior toward chemical reagents in general, and for the purpose of this paper it will suffice to consider fluorapatite as being the essential phosphatic constituent of these types of rock. The available data1 indicate that the different commercial types of domestic phosphate rock usually contain about 12 to 52 per cent more fluorine than theoretically is required to form fluorapatite with all the phosphorus. Calcium fluoride (fluorite) has been definitely identified in only a very few of the samples that have been examined1,2. Bredig and co-workers4 state that fluorapatite can take into its crystal lattice excess calcium fluoride to the extent of approximately 70 per cent of that theoretically required by the formula Ca10F²(PO4)6 without causing more

Jan 1, 1938

By D. S. Reynolds, K. D. Jacob, H. L. Marshall

All types of commercial phosphate rock produced throughout the world contain fluorine in quantities ranging from approximately 0.4 to 1.3 per cent in the Curacao and Christmas Island phosphates to 3.1 to 4.2 per cent in the phosphates of the United States and North Africa1. For a given type of rock, the fluorine content is usually roughly proportional to the phosphorus content. Significance of Fluorine in Phosphate Rock On the basis of chemical and X-ray diffraction studies, Hendricks and co-workers2 concluded that fluorapatite, Cal10F2(PO4)6, is the essential phosphatic constituent of the commercial types of domestic phosphate rock. On the other hand, Bredig and co-workers3 have recently advanced the opinion, also based on X-ray diffraction studies, that the mineral phosphates usually contain carbon dioxide in the apatite lattice, and that the phosphate rocks of the United States are really fluorcarbonate apatites. However, the domestic types of phosphate rock do not seem to differ greatly from coarsely crystalline fluorapatite in their behavior toward chemical reagents in general, and for the purpose of this paper it will suffice to consider fluorapatite as being the essential phosphatic constituent of these types of rock. The available data1 indicate that the different commercial types of domestic phosphate rock usually contain about 12 to 52 per cent more fluorine than theoretically is required to form fluorapatite with all the phosphorus. Calcium fluoride (fluorite) has been definitely identified in only a very few of the samples that have been examined1,2. Bredig and co-workers4 state that fluorapatite can take into its crystal lattice excess calcium fluoride to the extent of approximately 70 per cent of that theoretically required by the formula Ca10F²(PO4)6 without causing more

Jan 1, 1938

By Herbert Clark Hoover, Lou Henry Hoover

QUESTIONS of assaying were explained in the last Book, and I have now come to a greater task, that is, to the description of how we extract the metals. First of all I will explain the method of preparing the ore1 ; for since Nature usually creates metals in an impure state, mixed with earth, stones, and solidified juices, it is necessary to separate most of these impurities from the ores as far as can be, before they are smelted, and therefore I will now describe the methods by which the ores are sorted, broken with hammers, burnt, crushed with stamps, ground into powder, sifted, washed, roasted, and calcineda.

Jan 1, 1950

Jan 1, 1951

By Dorsey Lyon

INTRODUCTION THE electric furnace has always been found to be especially adapted to melting, refining, and finishing processes throughout its gradual acceptance by metallurgists, as a practical apparatus for conducting metallurgical operations. In the steel industry, the electric furnace is firmly established in the manufacture of steel of the highest grade, equal to crucible steel. For the production of the cheaper grades of steel in large tonnage, the electric furnace gives a higher-grade product than the open-hearth or converter, but due to the high cost of power prevailing in steel centers, considered from the electric furnace standpoint, it is not economical to produce tonnage steel in the electric furnace. As a refining and finishing agent for open-hearth or Bessemer steel, the electric furnace has had some degree of success in the production of tonnage steel. After a study of the use of the electric furnace in the steel industry, it appears that there may be a possibility of its use to advantage for the melting of cathode copper. In the case of copper the problem is not one of actual refining, because the copper if refined properly y the electrolytic method needs no further refining; it needs simply to be cast into a marketable shape. The name" refining". is applied to the present finishing process, because in the operation oxygen and other impurities are removed, which the electrolytic copper absorbs in being melted in the reverberatory furnace. Considering that processes may be positive, negative, and neutral; the electrolytic method would be positive; reverberatory melting of cathode copper, negative; and electric furnace melting, neutral. The electrolytic method produces about as pure a copper as is possible, if operated properly and the anodes are not too impure. The final reverberatory melting of this cathode copper lowers the grade of the final product, due to the absorption of gases and impurities.

Jan 8, 1914

By Robert B. Hoy

To maintain a competitive position in the world market in spite of higher domestic labor costs, the U.S. has been forced to the forefront in developing labor saving devices. This has resulted in automation in our factories, mechanization in our mines, and development of faster and more economical methods of transportation. Since World War II the domestic mining industry has suffered perhaps more than any other sector of our economy. When we assisted our allies-and our enemies-to get back on their feet following the ravages of war we were perhaps overly generous in providing funds and technical assistance to develop foreign mining industries that have since become thorns in the side of our own industry. It has become imperative that domestic industry exert its vigor to meet the challenge of foreign competition. While the domestic industry can meet this challenge of foreign competition in part by protective tariffs, quotas and governmental aid, the most effective way is to maintain technological superiority that will reduce manpower requirements and costs and increase productivity. There is this opportunity both in mineral processing and in mining.

Jan 9, 1962

By Harold Roast

THE object of this investigation was to compare the arsenical antimony-lead alloy with some of the regular bearing-metal alloys. With this end in view, the following tests were made: 1. Chemical analyses to show the composition. 2. Thermal analyses. 3. Macroscopic examination of fractures. 4. Microscopic examination. 5. Tensile tests. 6. Crushing tests. 7. Scleroscope tests. 8. Brinell tests, at temperatures from 80° to 400° F. Tests 3 to 8 were conducted on both sand-cast and chill-cast specimens. For the purposes of this paper the alloys have been numbered from 1 to 6; their composition is as follows: LEAD, ANTIMONY, TIN, COPPER, ARSENIC, NUMBER PER CENT. PER CENT. PER CENT. PER CENT. PER CENT. 1 82.64 12.95 4.40 0.01 none 2 27.54 9.94 59.87 2.65 none 3 77.65 20.75 none 0.13 1.47 4 82.95 16.85 none 0.20 none 5 83.78 15.35 none 0.05 0.82 6 0.15 7.87 84.13 7.85 none The analysis, in the case of the antimony, was made by solution in sulfuric acid and titrated with permanganate. For tin, the ferric-chloride method was used; for copper, the alkaline separations, and the thiocyanate methods; for arsenic, volatilization of arsenic and titration with iodine. The lead, with the exception of alloy 6, was taken by difference.

Jan 2, 1922

By F. R. Hensel

PuRe silver and silver-lead alloys have been studied as to their suitability for bearing~.&apos; A review of the properties of thallium and the silver-thallium constitutional diagram was made by the author to analyze the possibilities of silver-thallium compositions for antifriction materia1s. t The silver-rich end of the diagram as reported in the literatureg-" was found to be sketchy and it was necessary to carry out corisiderable experimental work to arrive at definite conclusions. Some of the results of this work are reported in this paper. Test Materials In the beginning of the work, only fused alloys were investigated. Later, research Table i.—Composition of Fused Silver-thallium Alloys Tested for Antifriction Properties Percentage Alloy No. of Thallium 1533...................... 0.48 1534.................... 1.06 a31 HT................... 2.04 231....................... 2.10 232 HT................... 3.83 Balance 232....................... 4.07 Silver 233 HT................... 5.86 a33....................... 6.38 a34....................... 9.84 a34 HT................... 10.07 was carried out on electroplating methods and diffusion processes. In preparing the fused alloyst care was taken to exhaust the toxic fumes caused by the thaillium content. The compositions of the series of fused alloys are listed in Table I. The silver-thallium alloys were melted in clay-graphite crucibles and cast into preheated steel molds of 3/4-in, diameter. In the cast condition, they showed a cored structure, as indicated by the micrographs of Figs. I to 3. The etching reagent used was a mixture of 2 grams K2Cr207, 8 C.C. H2S04, and IOO C.C. H20. The cored structure is unsatisfactory for the type of corrosion resistance required for bearing applications, and homogenizing experiments were carried out at various temperatures, the results of which are shown in Figs. 4 through 8. The alloys with a lower thallium concentration, which were heated for 2 hr. at 525°C show an almost completely homogenized solid solution type of structure. With higher thallium concentration, the homogenizing temperature was dropped to 475OC. to eliminate the formation of a liquid phase. It is evident that heating for 2 hr. at this temperature did not iesiilt iii complete elimination of the cored structure. As would be expected, cold-working of the cast structure is an expedient in establishing equilibrium conditions. The fine homogeneous grain structure shown in Fig. 7 corresponds to the cold-worked area under the Rockwell ball penetration when the hardness was taken before heat-treatment. A detailed structural study was made on a cast silver-thallium alloy containing 3.67 per cent thallium. Three micrographs (Figs. 9, 10 and 11) show the transition

Jan 1, 1946