Search Documents

By E. S. Machlin

The possibility that formation of voids under creep-rupture conditions may take place by the condensation of vacancies has been investigated theoretically. It has been concluded that nucleation of voids under creep-rupture conditions by vacancy condensation is highly improbable. However, growth of pre-existant voids by vacancy condensation is probable. A number of predictions made in this theory have been verified by the data. It has been predicted and checked that the product of rupture life and steady-state creep rate for preannealed metals and single phase alloys is an approximately invariant quantity, independent of stress, temperature, and atomic number for a given type structure. The direction of the effect of cold work on this product has been predicted and found in agreement with experiment. A number of experiments to evaluate the vacancy condensation mechanism further are described. SEVERAL papers have appeared recently which speculate on the origin of voids formed at grain boundaries under stress.' ' The object of this paper is to examine quantitatively the proposition that the voids produced in a creep test are a result of vacancy condensation. A result of this paper is a theory of creep-rupture. Void Nucleation Application of standard nucleation theory" to the problem of void nucleation leads to the following conclusions: 1—Homogeneous nucleation of voids requires a supersaturation ratio (concentration of vacancies in supersaturated to that in saturated solution) of 400 for a reasonable surface energy of 1000 erg per cm-and 1.4 for the improbably low surface energy of 10 erg per cm. 2—Heterogeneous nucleation of voids at plane interfaces between two phases requires a supersaturation ratio of 2.5 for a typical contact angle of 145 3-—Void nucleation about a solid particle may be accomplished at a supersaturation ratio of 1.17 for a typical value of work of adhesion? of 60 erg per The work of adhesion is the surface work 10 replace two solid-vauor surfaces by a solid-solid interface. enr ' between an oxide and a metal in the presence of a surface active element such as sulphur. Estimates of the supersaturation ratio at which voids are produced in diffusion experiments yield a maximum of 1.01. Inasmuch as the foregoing mechanisms of void nucleation probably will not operate at this level—too low a surface energy is required—the investigatol. is led to the conclusion that voids must already exist. That is, nucleation of voids probably does not occur. Rather, existing submicroscopic voids grow out to visible size. Already existing voids might be produced during solidification or working. Supercritical sized parlicles which contain cracks may act as heterogeneous void nuclei. Gas pockets may act as void nuclei. Experiments are desired to determine the nature of the heterogeneous void nuclei which grow out to voids in both diffusion and creep experiments. Void Growth Void growth might occur in at least two possible ways, depending upon whether the already existing void nuclei are at grain boundaries or within the grains. In the case of a spherical void far from a crystal boundary, vacancies are generated during creep as a consequence of the migration of suitable dislocation jogs' and are also annihilated at sinks. Under these conditions, a steady-state concentration of vacancies is built up in the crystal, defined by the condition that for any differential volume the rate of generation of vacancies in that volume equals the rate of annihilation of those vacancies." This equality would lead to the development of a gradient of vacancy concentration radially outward from the void surface up to a radius where the vacancy lifetime becomes equal for all directions of vacancy migration. The distance over which this vacancy concentration gradient extends equals about 2vD,T* where D, is the vacancy diffusivity and T:' the vacancy lifetime in a crystal outside the gradient in a zone of constant vacancy concentration. The vacancies generated in the region over which the gradient exists will annihilate more often at the void than elsewhere. Approximately a little over one-half the vacancies generated in the gradient zone will annihilate at the void. Hence, the growth rate of the void is given by on where R is the radius of void in centimeters, is the atomic volume, and R is the rate of generation of vacancies, number per centimeter" per second. R D and T* may be estimated in terms of other physical parameters." In particular, R = n.j e/b [3] where n is the average number of vacancy produc-

Jan 1, 1957

By Oliver Bowles

DISCUSSIONS of trade and commerce are generally more comprehensive today than in the past; the problems are approached with a vision unrestricted by national boundaries, and broad enough to comprise the entire world. The extent to which the limited viewpoint that has characterized past ages is yielding to an economy of world-wide scope is exemplified by the Atlantic Charter which blazes a trail in the direction of trade principles that aim to preserve the interest of each individual country in the commonwealth of nations. Its fourth article promulgated the principle that all nations should have access on equal terms to the trade and to the raw materials of the world which may be needed for their economic prosperity. Future developments in reciprocal international trade may have some effect upon the flow of nonmetallic minerals but such effects are not likely to be great because tariffs and trade policies have not affected that flow profoundly in the past. Nevertheless conditions may change and new problems may arise demanding important decisions. Sudden changes are not to be expected, but rather an orderly evolution in which national interests will merit due consideration in establishing broader policies.

Jan 1, 1945

By Mara Kosovac, Sujan K. Kundu

The Iron Ore Co. of Canada (IOC) has developed a computerized plan analysis method for its open-pit iron mining operations which will eliminate much of the tedious manual drafting of pit design plans performed by engineers and geologists at its two major operational areas near Schefferville, Que., and Labrador City, Nfld. The new technique permits analysis of section or bench plans for a specific ore body, based on drillhole information; preparation of a three-dimensional unit profit matrix for pit design purposes, and storage of extensive ore-block information for other applications. Other advantages include enhanced design accuracy through reduction of human errors normally associated with preparation of large data masses, and by elimination of errors inherent in planimeter-prepared ore block diagrams.

Jan 7, 1978

By D. W. Frommer

Processing nonmagnetic taconites by selective flocculation-desliming and flotation requires large volumes of water. If impounded without treatment, these off-process waters require excessively large areas for containment. To discharge the waste water into natural waterways would contribute to stream pollution and likely would not be permitted. In U.S. Bureau of Mines experiments conducted in the Twin Cities Metallurgy Research Center's 900-lb per hr pilot plant, approximately 85% of water requirements for the flotation-based treatment of a Michigan nonmagnetic taconite were met by reclaimed water. Water reclamation of the off-process streams from flotation was accomplished by controlled additions of lime, sodium carbonate, and a synthetic flocculant to reduce turbidities to 51000 ppm equivalent SiO*, while maintaining a Ca(II) content of =16 ppm in the finished effluent. Flotation concentrates of good quality were obtained using the reclaimed water. The cost of chemicals used in water reclamation was approximately equal to the savings in flotation reagents attributed to recycling of the water. Water quality is perhaps as important to flotation as are the reagents used. The character of water is extremely variable, depending on whether the source is a well, lake, or stream, upon the season and temperature, upon prior use, and upon the character of the watershed. All of these factors influence the water hardness and the quantity of other dissolved inorganic salts, turbidity, dissolved and suspended organic matter, dissolved gases, and pH. Frequently, the differences in water quality can measurably influence flotation selectivity, often to the point of spelling success or failure. Water hardness is particularly troublesome in flotation systems employing fatty acids, but other unrecognized constituents may also contribute to peculiarities in flotation behavior. Furthermore, a given water source may be entirely satisfactory in one flotation system, but entirely inappropriate in another. In recent years, society has given more attention than formerly to water use, even in areas where water is plentiful. However, both the demands of a growing population, with increased per capita needs, and also those of industry must be met. As a result, riparian rights must be negotiated with the appropriate government agency or agencies so that consumption of water is often allocated or otherwise controlled. Furthermore, the disposal of off-process industrial and domestic water is coming under the increasing scrutiny of these same governmental units. In these respects, the mineral industry is no exception, so that conservation, water reclamation, and reuse may be expected to assume increasing importance. In 1932, it was stated that, "water reclamation is generally more expensive than the economy in water and reagents resulting from its use. It is employed only if it is urgent to save water."' The economic aspects of this statement may still be true, but the unrestricted use of water is becoming less and less an option of the user. The purpose of this paper is to discuss an investigation conducted by the U.S. Bureau of Mines (USBM), in which water reclamation and treatment were undertaken to develop procedures for, and to assess the effects of, water reuse on the flotation treatment of nonmagnetic taconites. This investigation is a logical extension of previous work described by the author and associates at the Twin Cities Metallurgy Research Center employing selective flocculation-desliming and anionic flotation of silica from low-grade, nonmagnetic iron ores2,8 The requirements for the selective flocculation-de-sliming and the anionic flotation of silica processes determined the direction of the investigation. Previous studies had indicated that pH levels of about 11.0 and 11.8 were required for selective flocculation and flota-tlon, respectively. The calcium content of the water was believed to be of importance in both of these operations, and since Minneapolis tap water with a Ca(I1) content of about 16 ppm had been successfully used, an attempt was made to reclaim the process water at an equal level of dissolved calcium. Additionally, the objective was to nullify or effectively limit the effects of dispersants and fatty acid residuals from prior stages of processing. Last but not least, the system of water treatment had to have the capability of reducing turbidities to workable levels. With about half of the effluent being derived from the selective flocculation-desliming step and carrying about 25,000 ppm of highly dispersed, suspended fines, this last objective appeared formidable at the outset. Procedures for water reclamation were derived, in part, from well-known mineral dressing practices, from past observations and investigations, and from concepts contained in various pertinent publications on water treatment."c These procedures involved: 1) flocculation with lime and poly electrolyte-type flocculants, 2) lime-soda-ash softening, 3) chemical precipitation, and 4) mineral surface adsorption. Control was exercised at various stages of water reclamation by frequent measurements of Ca(11), pH, and turbidity.

Jan 1, 1971

By T. W. Atkins

ATHOUGH the magnesium industry in this country is about thirty years old, not until American industry began to amaze the rest of the world and confound our enemies with the extent and variety of our war production did the industry begin to come into its own. At the outset of the war, only three companies were producing and fabricating magnesium in this country. Today, about sixty companies are producing, casting, forging, extruding, rolling, and stamping this lightweight champion of metals. Experience in alloying, processing. and fabricating the metal gained during the war years is now being translated into hundreds of civilian peacetime applications. In no sense should magnesium be considered as a substitute for other metals. It has come into popular favor because If many unique properties in addition to is being the lightest known structural metal. These attributes are toughness, igidity, corrosion-resistance, and the ease with which it can be machined and worked. Magnesium is the third most abundant element in nature. Sea water, magnesite,

Jan 1, 1946

By D. R. Mitchell

MEETING for the thirteenth time in New York as part of the five-ring circus known as the Annual Meeting A.I.M.E., the Coal Division experienced a wartime boom in attendance. Technical sessions were crowded and whereas 65 seats were set up for the annual luncheon meeting of the Division over 100 members showed up, many of whom had to be fed elsewhere. Possibly the Coal Division should adopt "13" as its lucky number. Discussions at technical sessions, formal and informal, were lively. Those papers containing material directly concerned with the war, or containing information that might be usable for war industries, were enthusiastically received. Some criticism was made in regard to the present method of handling discussions and it was suggested that better success would be had in getting discussions in the record by the use of hired reporters. This is being considered by the executive committee of the Coal Division.

Jan 1, 1943

By Scott Turner

HOSTS of friends will rejoice that T. A. Rickard has been given honorary membership in the Institute. It might well have been done long ago, since, when one reviews distinguished services rendered by individuals to our organization and our profession, it is at once apparent that his name ranks high and that he has merited this distinction for more than three decades. Our by-laws restrict this list to twenty names; "T.A." becomes the sixteenth living member. Young engineers should particularly be pleased; Mr. Rickard has had a career rich in human interest, and full of useful suggestions to the younger men; he has given them good advice and set them a notable example; he, more than anyone else, has shown them how technical writing can be clear and concise; he has inspired youngsters to do their best; he has been their friend. No one has more first-hand knowledge of these facts than the writer of this appreciation:

Jan 1, 1935

By James E. Harding

AT just about the geographical center of the peninsula of Lower California is the El Arco gold mine. It is small and spotty, and three separate attempts to operate it in the past have failed. The only reason the present operation is possible is because of the higher price of gold and because the previous operators had spent about $300,000 developing the property with shafts, four levels, machinery, and a complete mill, all of which was acquired at a bargain price. All the known ore in the mine, to say nothing of the cost of recovering it, is

Jan 1, 1937

By Paul Weir

PRODUCTION METHODS in the bituminous coal mines in the United States are undergoing many changes. Although the primary object of these changes is the production of a better product at a cheaper cost there are other considerations such as the improvement of conditions under which miners live and work. The almost complete unionization of the manual workers in the industry during the past four years has 'brought with it a stabilization of wages on a relatively high basis and of hours of work per day and per week on a relatively low basis. With differentials in wages between producing districts firmly established, and with a nation- wide and uniform application of in-

Jan 1, 1937

By Edward Saibel

The object of this study is to investigate the effect of prior tensile strain on the fracture stress of a metal. This is done in a theoretical manner starting from the point of view developed by the author in his thermodynamic theory of the fracture of metals. The results are compared with experimental findings and a rational interpretation is given to work that shows the variation of fracture stress with prior tensile strain. Theory op Fracture In the thermodynamic theory of the fracture of metals developed earlier,' it was shown that a critical strain energy per unit volume exists. This is characteristic of the material and may be calculated from basic thermodynamic data. When the area under the flow curve reaches this characteristic value, fracture occurs. The general criterion for fracture is expressed in the form « ± u. = JLJW/V [r] where L, is the latent heat of melting of the unit volume, AV/V is the ratio of the change in volume of the unit volume to the original unit volume on passing from the solid to the liquid state, uo is an initial energy density, and J is a conversion factor, which changes energy from heat to mechanical units. As a first approximation, it will he assumed that the stress-strain curve is the straight line that extends from the point of maximum load onward, extrapolated back to the axis of zero strain, for example, line AC of Fig. I. If the point of intersection of the straight line with the axis of zero strain is represented by v., and the slope of the straight line is p, the analytic form of the flow curve is a = (To + pd [2] and the strain energy per unit volume evaluated from Jud6 becomes (u,6 + pa2/2). When this latter term reaches the critical value JLbVIV (designated hereafter by M), it is assumed that fracture occurs. This leads to the following expression for the fracture stress: a; = V«r.2 + iMp [3] The strain at fracture may be calculated from Eqs 2 and 3. It is assumed in this paper that the initial energy density is either zero or that it may be neglected. Furthermore, the complicated states of stress and of strain existing in the necked region of the tensile specimen after "necking" has occurred will also be neglected for the present, so that average conditions will be assumed to prevail. Flow and Fracture Curves LudwigZ attributed to materials two fundamental properties: (I) a resistance to flow and (2) a resistance to fracture. He reasoned that at each instant the

Jan 1, 1948

By Edward Saibel

The object of this study is to investigate the effect of prior tensile strain on the fracture stress of a metal. This is done in a theoretical manner starting from the point of view developed by the author in his thermodynamic theory of the fracture of metals. The results are compared with experimental findings and a rational interpretation is given to work that shows the variation of fracture stress with prior tensile strain. Theory op Fracture In the thermodynamic theory of the fracture of metals developed earlier,' it was shown that a critical strain energy per unit volume exists. This is characteristic of the material and may be calculated from basic thermodynamic data. When the area under the flow curve reaches this characteristic value, fracture occurs. The general criterion for fracture is expressed in the form « ± u. = JLJW/V [r] where L, is the latent heat of melting of the unit volume, AV/V is the ratio of the change in volume of the unit volume to the original unit volume on passing from the solid to the liquid state, uo is an initial energy density, and J is a conversion factor, which changes energy from heat to mechanical units. As a first approximation, it will he assumed that the stress-strain curve is the straight line that extends from the point of maximum load onward, extrapolated back to the axis of zero strain, for example, line AC of Fig. I. If the point of intersection of the straight line with the axis of zero strain is represented by v., and the slope of the straight line is p, the analytic form of the flow curve is a = (To + pd [2] and the strain energy per unit volume evaluated from Jud6 becomes (u,6 + pa2/2). When this latter term reaches the critical value JLbVIV (designated hereafter by M), it is assumed that fracture occurs. This leads to the following expression for the fracture stress: a; = V«r.2 + iMp [3] The strain at fracture may be calculated from Eqs 2 and 3. It is assumed in this paper that the initial energy density is either zero or that it may be neglected. Furthermore, the complicated states of stress and of strain existing in the necked region of the tensile specimen after "necking" has occurred will also be neglected for the present, so that average conditions will be assumed to prevail. Flow and Fracture Curves LudwigZ attributed to materials two fundamental properties: (I) a resistance to flow and (2) a resistance to fracture. He reasoned that at each instant the

Jan 1, 1948

By Henry N. McCarl

Mineral aggregates are those natural and manufactured industrial mineral and rock materials that provide bulk and strength in port- land cement concrete, bituminous concrete mixes, and plaster or stucco surfaces. They may also provide special characteristics such as thermal and acoustical insulation, weight, surface textures, abrasion resistance, and impermeability to various concrete products and mixes. Most aggregates are relatively inexpensive materials, but despite their low unit value, the tonnages consumed each year in the United States and throughout the world make mineral aggregates by far the leading industrial mineral and rock materials both in terms of volume (tonnage) produced and value consumed. The major use of mineral aggregates is in concrete. The low cost, high bulk aggregates tend to keep concrete construction costs at levels competitive with other building materials. Other major uses of aggregates include highway and railroad base or ballast materials, graded fill, and various industrial uses such as metallurgical and chemical fluxes and raw materials-these latter uses are often considered nonaggregate uses of mineral aggre- gate materials. The value of mineral aggregate materials at the production plant varies from less than a dollar per ton to several dollars per ton for most crushed stone and sand and gravel, $2 to $15 per ton for slag and expanded clay or shale aggregate, to as much as $60 to $100 per ton for expanded perlite or vermicu- lite. The more specialized the use, the higher the price-although there are naturally some exceptions to this rule of thumb. The first four parts of "Construction Materials" deal with the utilization of four major mineral aggregate types: Crushed Stone, Light- weight Aggregates, Sand and Gravel, and Slag. While the focus will be on the use of these industrial minerals and rocks there will also be some coverage of sources, mining and production, especially in those cases where they are

Jan 1, 1975

By K. R. Janowski, H. Conrad

As part of a program to establish the effect of crystal imperfections on laser output, a detailed study was made of the dislocation structure of ruby crystals obtained from varioius sources. Using KHSO4 as an etchant, a detailed mapping of the dislocation structure on the (0001) and the (1150) planes was carried out. A less extensive study was made of the rhombohedral planes. The average dislocation density on the basal plane was 1.5 to 3 x 106 cm&apos;2 and on the (1120) planes -5 x 10&apos; cm-2. Howe7!er, considerable variation existed between areas on a given plane. The subboundaries in the basal plane tended to lie along [1100] type directions while those on the (1120) plane tended to lie: a) parallel to the basal plane, b) along truces of the (1101) plane, and c) along normals to the traces of the (0001) planes. The orientations suggest that mang of the dislocations lie on the (0001), (1701), and (1150) planes A Laue back-rellection nnalysis Of c-axis wander in one crystal revealed a gradual increase in misorientation from me end of the crystal to the other, with a maximum variation of 1°35&apos;. Slight etching of a mechanically polished crystal revealed mumerous polishing scratches, suggesting the existence of a plastic flow layer. It is recognized that chromium concentration, lineage, and other crystalline imperfections play a role in the efficiency of ruby lasers.&apos; Consequently, it is desirable to establish in detail the imperfection structure of ruby crystals to be used as lasers. Some exploratory work along this line had already been done by Barnes&apos; and Dils and Martin.&apos;" How- referred to as the morphological system, as described by Kronberg.4 The Miller indices given in the present paper will be based on this morphological system. In this system, the three common growth planes are the (0001), the {1120}, and the {1101}.5 Since these planes are of high stability, it is expected that they are most suitable for study by the etch-pit technique. In the present investigation, a detailed mapping of the dislocation structure was carried out for the (0001) and the (1130) planes. A less extensive study was made of the etch-pit structure on rhombohedra1 planes. An analysis of dislocations in sapphire (the ruby host) was first made by kronberg,4 who postulated that slip on the (0001) plane occurred by motion of dislocations with Burgers vector 1/3 <1150> and that these dislocations might dissociate into quarter partials. An etch-pit technique using boiling phosphoric acid was developed by Scheuplein and Gibbs6, 7 for identifying dislocations intersecting the (0001) planes and the planes near (2021) in sapphire. Al-ford and Stephens8 were able to reveal dislocations on the (0001) and {1120} planes in sapphire and ruby by etching in fused potassium bisulfate (KHS04) at 675°C. The termini of basal dislocations [(000l), <1120>] were revealed by Palmour and Kriegel9 on {1120} and {1010} by thermally etching sapphire. Bond and Harvey10 were able to decorate dislocations in sapphire by adding 1 pet by weight of ZrO2 to the Al2O3 powder used in the growth of the crystals by the Verneuil technique and then heating the grown crystals for 4 hr at 1500°C. They found, using optical transmission microscopy, that many dislocations had straight segments which were parallel to one of the six [1120] directions in the basal plane. Single dislocation lines curved smoothly from one alignment to the other, turning through angles of 60 to 120 deg. Also observed were isolated hexagonal loops, approximately 10 µ in diameter, the sides of which lay along the same directions as did the longer dislocations. MATERIAL AND ETCHING PROCEDURE The ruby specimens used in this study (all containing approximately 0.04 pet Cr) had been obtained from four different sources: Linde Co., Meller Co., Valpey Crystal Corp., and those grown at Aerospace Corp.* For the initial phase of this study, several specimens were cut from the slab shown schematically in Fig. 1 which had previously been cut from a disk boule obtained from the Linde

Jan 1, 1964

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

By W. J., Kroll

MOST people believe that rare metals are always, scarce in nature, expensive to make, and therefore useless despite some miraculous properties which might make them a cure-all. There are&apos; some metals, which are quite frequent in nature, such as zirconium, which are called rare only because our present methods for making them are elaborate, thus forcing the manufacturer to sell them at a high price. There are also truly rare metals, such as gallium, which do not occur frequently in ores, but are easily reducible from their oxides. In these cases the price of the concentration operation is the decisive factor. The distribution of the elements in the earth&apos;s crust is no indication as to the availability of a metal; the concentration operation is the critical factor. Concentration is frequently obtained in the course of metallurgical operations for the extraction of other metals, and the rare metal may be enriched in by-products, flue dusts, mother liquors or precipitates from electrolyte purification as are indium, thallium, selenium, and tellurium. A periodic table of the rare elements may serve as a basis for discussion of their properties and to establish a program. (Table 1.)

Jan 1, 1946

By Alfred Boyles

"Heredity"1 in cast iron has been a subject of much discussion. Numerous experimenters have found that the properties of gray iron may vary greatly without corresponding variations in composition or thermal treatment. The main structural difference in such cases is in the size and distribution of the graphite flakes and the explanations given usually attribute this difference to some chemical element not shown by ordinary analysis or to some physical factor, such as inclusions in the melt. It cannot be said that any of these theories is completely satisfactory. Much remains to be learned about cast iron and for this reason a study of the material was undertaken as a part of the program of fundamental research at Battelle Memorial Institute. A review of the literature indicated that very little systematic work had been done on the mechanism of freezing in cast iron. The experiments described below are largely concerned with that problem. Normal and "Dendritic" Cast Iron As examples of variation in type of structure, photomicrographs of two test bars of cast iron are shown (Figs. 1 and 2) and the composition and properties are given in Table 1. Both are common, unalloyed gray iron. Test bar No. 13 has normal graphite flakes while No. 49 has very fine, lacy graphite arranged in a dendritic pattern, the matrix in both being pearlite. These two types of cast iron are well known to foundry-men and need no detailed description.

Jan 1, 1937

By A. W. Gauger

It is with some trepidation that I approach my subject, for I know that I shall at once incur the suspicion of the mechanical engineer, with his concern for boiler tests and efficiencies; of the mining engineer, with his mechanization problems; and of the chemical engineer with his unit processes. Nevertheless, it must be recognized that the technology of fuels, the systematic body of knowledge relating to the production, processing and utilization of mineral fuels, has grown to such proportions and involves so many widely diverse applications of fundamental science and engineering that it behooves us to stop and consider just what its status is in relation to other technologies, as well as in relation to the present and future needs of the social order. The time has come when technologists, applied scientists and engineers must consider the possible effects that their achievements may have on Society. The development of a machine to - -replace -several hundred men is a fine achievement when considered solely from the point of view of creative endeavor. But what of the men who are displaced by the machine! Does not the responsibility for the development of this machine embrace as well the consequences of obsolescence and technological unemployment resulting from such development? I believe that it does and that we must recognize this fact in our practice of engineering and tech- nology as well as in the training of future engineers and technologists. Magnitude of the Fuels Industry Fuel technology is the body of knowledge that relates to the mineral fuels. The fuels industry is by far the most important of all Our mineral industries. The chart in Fig. I, reprinted from U. S. Bureau of Mines Information Circular No. 6643, indicates the compartive values of metals, fuels and other nonmetallic minerals for the year 1929. Of the grand total of 13¼ billions of dollars in value of minerals at the mines, the mineral fuels contributed 48 per cent. Coal, with 34.4 Per cent, exceeded the value of any other single mineral. In fact, the value of the production of the Pennsylvania anthracite mines alone anand exceeds the value of the gold production of the entire world. Petroleum and natural gas in 1929 contributed 14.3 per cent and 3.3 per cent, respectively, of the total value of world mineral production. So much for the world picture; let us now look at the situation in the United States. Over the 60-year period 1880 to &apos;939, $46,409,727,000 of metal1ic products, $80,788,852,000 of fuels (coal, petroleum, natural gas, natural gasoline) and $27,871,-ooo,ooo of nonmetallic minerals other than fuels were produced. The mineral fuels have contributed 52.7 per cent of the entire mineral wealth produced over this period that has seen such tremendous industrial development in our Our As a matter of fact, our present industrial civilization has been made possible through the use of the

Jan 1, 1942

By A. W. Gauger

It is with some trepidation that I approach my subject, for I know that I shall at once incur the suspicion of the mechanical engineer, with his concern for boiler tests and efficiencies; of the mining engineer, with his mechanization problems; and of the chemical engineer with his unit processes. Nevertheless, it must be recognized that the technology of fuels, the systematic body of knowledge relating to the production, processing and utilization of mineral fuels, has grown to such proportions and involves so many widely diverse applications of fundamental science and engineering that it behooves us to stop and consider just what its status is in relation to other technologies, as well as in relation to the present and future needs of the social order. The time has come when technologists, applied scientists and engineers must consider the possible effects that their achievements may have on Society. The development of a machine to - -replace -several hundred men is a fine achievement when considered solely from the point of view of creative endeavor. But what of the men who are displaced by the machine! Does not the responsibility for the development of this machine embrace as well the consequences of obsolescence and technological unemployment resulting from such development? I believe that it does and that we must recognize this fact in our practice of engineering and tech- nology as well as in the training of future engineers and technologists. Magnitude of the Fuels Industry Fuel technology is the body of knowledge that relates to the mineral fuels. The fuels industry is by far the most important of all Our mineral industries. The chart in Fig. I, reprinted from U. S. Bureau of Mines Information Circular No. 6643, indicates the compartive values of metals, fuels and other nonmetallic minerals for the year 1929. Of the grand total of 13¼ billions of dollars in value of minerals at the mines, the mineral fuels contributed 48 per cent. Coal, with 34.4 Per cent, exceeded the value of any other single mineral. In fact, the value of the production of the Pennsylvania anthracite mines alone anand exceeds the value of the gold production of the entire world. Petroleum and natural gas in 1929 contributed 14.3 per cent and 3.3 per cent, respectively, of the total value of world mineral production. So much for the world picture; let us now look at the situation in the United States. Over the 60-year period 1880 to &apos;939, $46,409,727,000 of metal1ic products, $80,788,852,000 of fuels (coal, petroleum, natural gas, natural gasoline) and $27,871,-ooo,ooo of nonmetallic minerals other than fuels were produced. The mineral fuels have contributed 52.7 per cent of the entire mineral wealth produced over this period that has seen such tremendous industrial development in our Our As a matter of fact, our present industrial civilization has been made possible through the use of the

Jan 1, 1942

By G. F. LOUCHLIN

A FEATURE of the International Geological Congress to be held at Pretoria, South Africa, in the summer of 1929,. will be a symposium on the gold resources of the world. In this connection the U. S. Geological Survey and Bureau of Mines have been asked to prepare a report, showing production in the United States, describing the geology of its principal gold- producing districts, and estimating reserves (a) assuming a continuation of presen6economic conditions, and (b) assuming lower costs. This report will not be completed before April 1, but data thus far assembled are here presented with the hope of profiting by discussion and by information from those well informed on any of the important gold-producing districts. Gold production in the United States rose to a maximum exceeding $100,000,000 in 1915 and then rapidly declined to about $52,000,000 in 1920. Since then it has fluctuated, but on the whole slightly declined. Reviews of the eight leading states afford the following tentative conclusions :

Jan 1, 1929