Search Documents

By Ernest F. Burchard

(Pittsburg Meeting, March, 1910.) IN connection with the work of testing structural materials for the use of the U. S. Government at the laboratories of the technologic branch of the U. S. Geological Survey at St. Louis, Mo., from September, 1904, to April, 1909, and since then at Pittsburg, Pa., large quantities of sand, gravel, and crushed stone have been needed from time to time, besides samples of building-stone, clays, and other quarry-products. In many instances it has been necessary to obtain single samples of sand, gravel, or crushed stone in lots of a car-load or more. For obvious reasons all these collections have had to be made by a representative of the Survey. As the work progressed it was found essential that numerous geologic data should be gathered regarding the materials collected, in order that they might be properly classified as to kind of material, source, geologic age, etc., and that they might be rated according to quantity available, accessibility to transportation facilities, approximate costs, suitability for special purposes, etc., and that notes might be taken regarding undeveloped deposits of possible value. Furthermore, it was desired that the selection of materials for tests should be made broadly, so as to cover, first, the representative types of material, and later, if possible, the typical materials of the more important building-centers in the United States. In order to insure a certain degree of uniformity in this work and economy of effort and expense, it was decided that as much of the sampling as was practicable should be done by a member of the. geologic branch, whose regular field-trips could be combined conveniently with those necessary for procuring materials for the laboratory. During parts of the last three years I have been engaged in field-work of this sort.

Jun 1, 1910

By Chester W. Washburne

At present it is impossible to estimate closely the amount of oil obtainable from a given area of land. However, after the completion of a few properly distributed prospect wells, one can calculate the approximate yield of the sands penetrated, with a probable error of say 50 per cent. Even rough predictions of this kind are of value in large operations. Without wells upon it, one can never be absolutely certain that an area will produce any oil whatever, and one can only indulge in wild guesses of the probable productive area, before the geological structure has been carefully contoured and the top of the basal water plotted on a map. This requires wells. At times it is desirable to form an idea of the possible yield of oil in advance of drilling, as in cases where the price asked for undeveloped land seems too high, but where the probability of finding oil is furnished by neighboring development, supported by the geology. In such cases the most one can do is to make an estimate of possible maximum yield, which may of course far exceed results, and which is of use mainly in the prevention of excessive initial investment. The method is very significant in a general way, as in regions like the Bighorn Basin, Wyoming, where the productive sands in the Cretaceous shale are so few and so thin and fine that they cannot develop very great production, although the high quality of the oil probably will counterbalance this defect sufficiently to give local profit in favorable areas. Reservoir Capacity of Sands.—The porosity of a stratum is the measure of its maximum reservoir capacity for liquids and gases. The porosity may be determined experimentally and must be used in connection with the total volume of the sand.

Jan 1, 1915

By Wittenau, E.

OPERATION of a pilot mill of 100 tons' daily capacity during 1930 and 1931 proved that the copper minerals of the Colorado and Clay sections of the Morenci ore body could be successfully concentrated by the flotation process. Economic conditions caused postponement of further testing work until late in 1938 when the former No. 6 Concentrator at Morenci was converted into an experimental mill of 1500 tons' daily capacity which was known as the Test Concentrator. The Test Concentrator began continuous operation on April 3. 1939, using such crushing and grinding equipment of the No. 6 Concentrator as was appropriate. Modern classifiers and certain flotation machines were installed and later other types of flotation machines, a large grate-type grinding mill. mechanical screens, a short-head cone crusher, and a disk filter were added to the test equipment. Operation was uninterrupted until Dec. 31, 1941.

Jan 1, 1942

By John Branner

FIVE of the geologic horizons that yield oil in other parts of the world are represented in Brazil; namely, the Devonian, Carboniferous, Permian, Cretaceous, and Tertiary. Thus far, the first two have shown no, evidences of being oil bearing within Brazilian territory. Not enough exploring has been done to permit trustworthy comparisons of the relative importance of the Permian, Cretaceous, and Tertiary as oil-bearing horizons in this country. The most important, indeed almost the only, information available relates to the locations of the areas and to the structural features of the several horizons. The theories regarding the physical conditions under which these rocks were laid down, however, I regard of the utmost importance. PERMIAN Rocks of Permian age cover an enormous area in Brazil, extending from Rio Grande do Sul to Maranhão on the north, and to Matto Grosso on the west. These Permian rocks in many places are known to include oil-bearing shales and in some locations contain small veins of gilsonite. The geologic map of Brazil shows that the Permian area is widely distributed, but there is considerable doubt about 'the origin of some of the rocks:. Some of the lower Permian beds in southern Brazil contain marine fossils, but in Minas no fossils have as yet been found in them, and in Bahia, at only one locality have a few Permian plants been found. Indications of oil have been found in the states of São-Paulo, Paraná, and elsewhere farther south, but wells drilled in the Permian of São Paulo near the Morro do Bofete did not find oil. One well has been started, by the Brazilian government, in the Permian of Paraná near Marechal Mallet, close to latitude 26° south, but thus far oil has not been found.

Jan 6, 1922

THE purpose of this chapter is to present a general outline of the basic open-hearth process for the benefit of students, practicing open-hearth operators, and metallurgists who wish to review the subject. The discussion is limited to a description of the sequence and purpose of the operations, illustrated by data and examples. Subsequent chapters deal with more detailed and fundamental studies of the subject. The function of the basic open-hearth furnace is to convert various types of ferrous material into finished steel of given composition and quality. In comparison with other steel-making methods, the basic open-hearth process is one of the most versatile, both from the stand- point of the raw materials that can be used and the types of steel that can be produced. The process can be considered as a sequence involving melting, refining, and deoxidation. In the case of some types of liquid-metal charges the melting stage is not present, but refining and deoxidation in varying degrees are fundamental features of the process. GENERAL DISCUSSION OF THE BASIC OPEN-HEARTH PROCESS The first consideration in open-hearth practice is the type of charge on which the operation is based. This consists of three components-fluxing, oxidizing, and metallic materials. Fluxes. In the basic process the fluxing material is primarily lime, added in the form of either limestone (CaC03) or burnt lime (CaO). This is supplemented by magnesia (MgO) and lime from the furnace bottom and banks. The function of these fluxes is to form a slag with the silica (SO2), manganese oxide (MnO), iron oxides (FeO and Fe203), and phosphorus oxide (P205) that are produced by the oxidation of varying amounts of the silicon, manganese, iron, and phosphorus in the charge during melting and refining. The slag, composed of the basic fluxes and the neutral and acid oxides, floats on top of the steel bath when the charge is melted. The composition of this slag depends on the amount of each slag-forming element present in the charge and on the extent of oxidation of these elements during the course of the

Jan 1, 1944

By J. Walter Snavely

PRESENT-DAY processing in many industries, calcining, sintering, briquetting, beneficiation and nodulizing, increasingly calls for the handling of large volumes of hot bulk materials. Various types of conveyors have been employed. This discussion will cover the factors governing their selection. For temperature ranges up to 400°F, or approximately 200 °C, a wide range of conveyors is available. Special constructions of rubber conveyor belts, steel conveyor belts, vibrating and shaker conveyors, apron conveyors, and drag chain conveyors, all are used successfully. As temperatures go well above 400 2F, however, choice of conveyors is narrowly limited. This paper will consider the problem of handling bulk materials only where the temperatures exceed 400°F. The arbitrary selection of 400 °F as a dividing point undoubtedly can be challenged, as special conveyor belting constructions are available which are suitable for temperatures in excess of 400°F. However, when the relatively short life of such belts and the cost of their replacement, with the attendant down time, are balanced against the reliability and long service life of the properly designed steel constructed units to be discussed, there is little question in any operator's mind that the special belts are more expensive to use. Because the conveyors under study are for the handling of bulk materials, inevitably including a high proportion of fines, obviously wire mesh belts cannot be included for consideration. Even though this type of conveyor is widely used at high temperatures, i.e., for carrying glassware through a lehr, it is unsuited for the conveying of bulk materials, and therefore will be excluded from further discussion in this paper. Preliminary to the study of the conveyor itself is the determination as to whether the material is to be cooled while it is being handled, or whether the processing requires retention of all heat and the maintenance of a given temperature range. In the majority of cases cooling is incidental to or part of the handling process, when the handling, for example, follows completion of sintering, roasting, calcining, refining, or some other process. To meet such operating conditions successfully, the conveying medium used must have: 1—a construction capable of withstanding maximum initial temperatures of the material being handled. 2—a construction providing efficient heat transfer for cooling. 3—a construction providing dependable operation and long life with minimum service requirements, and 4—a construction providing controlled and efficient conveying. Under the usual conditions of cooling during the handling, the construction selected to withstand the initial maximum temperatures does not necessarily involve using alloys, as excellent results can be achieved with normal carbon steels and cast irons, when they are properly applied and proportioned. The earliest and simplest type of conveyor for handling very hot materials is the cast steel drag chain conveyor, still widely used for handling hot cement clinker, as illustrated by Figs. I and 2. Because of the rugged and generous proportions of the chain link design, low carbon steels are entirely suitable for the links. The pins, however, must be alloy steel. The simple, rugged construction of this type of conveyor makes it readily capable of withstanding high initial temperatures, even though the chain is operating buried in the material. The drag-chain type of conveyor has advantages and limitations. Although the efficiency of the heat transfer is relatively poor, the life of the conveyor is reasonably long, and because of its crude simplicity it does not require much servicing. However, as a conveyor, it is limited in capacity, and largely limited to horizontal runs. Furthermore, because of the crude design, heavy weight, and the chain operating at the temperature of the material, greatly reducing permissible operating chain pulls, this type of conveyor is limited to relatively short centers. Another type of conveyor that has been used for very hot materials is the cast pan conveyor. Because of its very generous proportions the cast pan, which is made of either cast iron or malleable iron, can withstand initial maximum temperatures. It also provides efficient heat transfer for cooling. Further, it is on efficient conveyor construction, which can be used for inclines. Because the chain employs rolling friction instead of sliding friction, and is not in the maximum temperature zone, much longer centers are possible. It is this type of conveyor that is frequently used in the casting of various metal pigs, pig iron, and aluminum; it is obvious, therefore, that very high initial temperatures are being handled. With this kind of conveyor the return run is frequently sprayed with water to accelerate heat transfer. The build-up of residual heat in the very heavy cast pans is thus overcome. The outboard roller steel pan conveyor is an improved pan conveyor' which provides high rates of heat transfer and substitutes formed steel pans for the heavy cast pans. It is a very efficient conveying medium. The details of this particular construction are clearly shown in Fig. 3. An early application of this type of conveyor is shown in Fig. 4. In this case the conveyor units are handling roasted phosphate rock at average temperatures of 1000" to 1500°F, and frequent maximum temperatures as high as 1900°F. Several widths are used. The capacity of the unit at a speed of 50 fpm is approximately 30 tph per inch of width at peak loadings, average capacity being about 1/3 of peak loading. The assembled conveyor is shown in Fig. 5, with views of both the top and the underside to show all the construction details. In particular, the following general design principles were carried out in this construction:

Jan 1, 1954

By G. H., Wigton

THE present milling operations of the Chief Consolidated Mining Co. consist- of flotation of oxidized minerals from siliceous ores of the Tintic Mining district, Utah. As the lead, silver, and gold minerals that give the ores economic value are almost entirely oxidized; their successful flotation has necessitated the solution of many new problems. Laboratory effort resulted in the selection of a, natural float for the oxidized minerals. 'By "natural float," I mean that no reagent was added to produce a sulfide film on the osidized minerals before or while subjecting them to flotation operations. As compared to methods involving sulfide filming, the natural float was selected because it promised successful treatment of a larger variety, of ores without change in quantity or kind of reagents, as well as a better economic balance between metal recovery and concentration ratio. In explanation, I can, state that with sulfide filming, the efficiency of the method decreases rapidly with increase of hydrated, iron osides in the ore, whereas with the natural float the same effect has not been noted. Evidence shows that although sulfidizing can produce greater metal recoveries, it yields a concentrate so much lower in grade that no advantage results.

Jan 1, 1928

By J. M. McKenzie

p-n junctions to detect and measure the energy of single quanta of electromagnetic radiation are described. Useful energy range is from 1 kev to several Meu. Achieved energy resolution varies from 30 pct at 6 keu to 0.12 pct at 2 Mev. Parameters affecting the perfornzance of the present detectors and desired of a new material are discussed. DURING the last 6 years semiconductor detectors have been used extensively to detect and to measure the energy of charged particles. These detectors are made from reverse-biased p-n junctions. Electron-hole pairs are created in the depletion region of the junction, Fig. 1. The carriers are separated by the electric field and give rise to a pulse of current in the external circuit. This current pulse is proportional to the number of carriers and hence to the energy deposited in the depletion region by the ionizing event. More recently the discovery of the lithium drift process, first in silicon' and then in germanium,2 has extended the use of semiconductor detectors to the detection and the energy measurement of single quanta of electromagnetic radiation. These detectors now have a useful measurement range extending from the soft X-ray region, about 6 kev, to the hard y ray region of several Mev. Surface-contoured avalanche diodes can be used to extend this range down to 1 kev. There is however a desire for other materials suited to higher operating temperatures, and particularly for those materials with high y ray stopping power. The most important advantage of the semiconductor detector over gaseous and scintillation detectors is the average energy, E, required to form an electron-hole pair. Fig. 2 shows the quantum efficiency for germanium as a function of photon energy.3 At the band-gap energy, 0.7 ev, an electron-hole pair is generated by the absorption of the photon and the quantum efficiency is unity. The quantum efficiency remains constant at unity between 0.7 and 3 ev. It then increases as additional electron-hole pairs are formed by secondary ionization of the initial photoelectron. The rate of increase is about 1 electron-hole pair per 3 ev (actually 2.9 ev for germanium and 3.6 ev for silicon). This figure is constant irrespective of the particle type (electron, proton, a particle, heavy ion) and energy. In an ionizing event an incident particle of energy E will create N = E/e ion pairs. The statistical fluctuation in this number is proportional to &. The fractional energy resolution is therefore proportional

Jan 1, 1968

By Bain, Edgar C.

THE results are presented of an investigation to discover the fundamental atomic conditions existing in Corson's high-copper alloys hardenable by means of silicide solution and reprecipitation. The study attracted the writer because it offered a very convenient example of the general type of hardenable alloys exemplified by duralumin. Sykes' iron-tungsten and iron-molybdenum alloys and the hardenable lead-antimony. SUMMARY OF RESULTS AND CONCLUSIONS In brief, the investigation shows that very perfect crystallinity exists in the solid solutions prepared at high temperature to contain as much dissolved silicide as possible. The lattice parameter of copper is altered very little by the amount of cobalt, nickel or chromium, and silicon dissolved. The hardening by drawing at a temperature to initiate precipitation of excess silicon and metal produces a remarkable change in the atomistics of the solid solution. The old perfection of crystallinity in the solid solution is destroyed and the new atomic spacings are of variable magnitude even in one grain, and a condition in a measure resembling that found in martensite is observed. Were no particles whatever precipitated by the drawing action, still ample causes for hardness would be in evidence in the solid solution alone. The lack of plane continuity in the crystal grains would oppose slip in a very effective manner. Complete annealing restores the crystalline perfection in large measure. In these alloys even the most sensitive methods failed to reveal the characteristic pattern of the silicide precipitated by the anneal, but this was largely to be expected as the amount is relatively small.

Jan 1, 1927

By F. Z. Schellenberg

(Pittsburg Meeting, March, 1910.) SYSTEMATIC exploitation in the Pittsburg coal-seam on a large scale is simple where the boundaries of the property do not interfere by forcing drainage-, ventilation-, and transport-lines of entries to be run to particular confined fronts. A prime condition governing development is the natural direction of the seam's perpendicular cleavage-planes, giving long lines of smooth faces near together and parallel, bearing about 65° to the left of the meridian and therefore crossing the basins. The gradients of dip into the basins change from 10 per cent at the east rim to practical flatness northwestward across the great coal-fields, a hundred miles wide; the clip being halved in rate at each successive crossing-over of an anticlinal crest. Elevations above sea-level on this transverse section, in scope of present development, differ by 1,000 ft. between low trough and high outcrop. Local irregularities of dip are found, but the main feature to be recognized is the pitch of the basins-the general rise northeastward at 20 ft. per mile, from 100 ft, below sea-level at the low point near the. SW. corner of Pennsylvania to 1,500 ft. and more above tide, and the appearance then, at the surface, of the lower coal-seams carried in the next deeper-lying thousand feet of rock-measures; below which series come the oil- and gas-sands of Oliphant's charted column of strata, reaching down altogether 3,000 ft. below the Pittsburg coal-seam. Because of -the general regularity of occurrence of the coal-seam, the mine-map depicting the courses of economic operation to be undertaken and the steps in controlled exhaustion, need be but a projection of two dimensions on the horizontal plane of space, and this for the most part composed of natural, almost unbroken lines, on the face and on the end of the coal, co-ordinating rectangularly.

Jul 1, 1910

By E. C. Bitzer

THE primary object of the work described in the following pages was to simplify the equipment in the separating circuit of the heavy-media process by substituting a spiral classifier for the separatory cone. Mechanical considerations were the leading attraction and the best that was hoped for on metallurgical performance was that the new vessel would give results equal to those obtained by conventional equipment. Tests have demonstrated in commercial operation on iron ore that the mechanical advantages of the spiral separator are about as predicted; also, the metallurgical performance is superior to the cone on the ores treated. Treatment of iron ore involves the separation of two products: a concentrate that sinks and a float product that contains true float material plus a controlled division of interfering middling. The middling material is heavier than the average specific gravity of the separating medium. Recent work with the spiral separator on Tri-State zinc ore showed that the middling material had to be recovered as concentrate because this fraction contained the bulk of the-zinc in the ore. It has been demonstrated that it is possible to make three products with the new separator on an ore such as this: a float tailing, a float middling, and a high grade heavy sink product. It appears from this last work that the new separator has definite mechanica1 and metallurgical advantages over any type of separating cone for treating feed that contains large amounts of material of a specific gravity close to that of the separating medium. However, either type of separator should perform equally well, metallurgically, on feed that is free of middlings. Each series of experiments with the spiral separator as required additional work to fully develop the possibilities of the machine. For this reason the paper is divided into chronological parts. History of Development A drag-type classifier was first proposed as a substitute for the cone separator by Butler Brothers technicians during the initial tests with galena medium at Crosby, Minn., in 1937. The desire for finding a substitute for the cone arose from trouble with interfering middlings and certain operating disadvantages of the cone. The possibility of using a spiral classifier was also suggested at this time by Emmett Butler and C. J. Abrams. However, inability to satisfactorily recover fine galena, which was used as a medium, terminated all development work at Crosby. During the winter of 1937--1938 investigation started on magnetic medium with concurrent s development of the inverted or closed- top cone, which was found necessary to eliminate iron-ore middlings with the float product. About

Jan 1, 1947

IN order to make his work easier, every master of any art whatever keeps always to the road that he has learned or that his skill or good judgment has shown him to be the best. Although there are various methods used in making moulds for guns, depending on whether they are large or small, nevertheless almost the same road is traveled in all. You must first know that it is necessary to make a pattern of wood or clay exactly as the gun is to be, with those ornaments of cornices and rings that you wish to be in the bronze. Let us suppose that you wish this pattern to be of wood. You must try to have for this a piece of fir as long and thick as you wish, dry, solid, and well seasoned, with few or no knots if possible. This should be longer than the gun by the length of the head and foot rests where it is pivoted [83v] so that it can be turned as on a lathe. On the end where the mouth is to be it should project out enough so that you can attach a feeding head at the top of the casting. You can make or have this pattern made round, fluted, spiral, or half fluted, as you like best, making the measurements exactly correct with all care and attention. Then two bearing trestles must be fixed firmly in the ground, one at the head and one at the foot, as is usually done with roasting spits and as you see drawn here. This done, if it is fluted, put the cornice pieces at the place where you wish the mouth to be and at the foot where the fire is applied. These are

Jan 1, 1942

By N. K. Chen, R. Maddin, R. B. Pond

A METHOD has been described by Andrade' for obtaining very rapid grain growth so that single crystals of high melting point metals could be made with comparative ease. The furnace construction was essentially a very thin wire through which was passed an electrical current so that "a high uniform temperature" was maintained. The wire was surrounded by a fused quartz tube from which the air had been evacuated. Andrade applied this method to the growth of single-crystal wires of alpha iron, and Tsien and Chow2 prepared single crystals of molybdenum 0.25 mm diam in this way. In the present report a method is described in which the basic idea of the Andrade furnace is utilized. However, modifications are employed so that large single crystals of molybdenum or of any refractory metals can be grown. Furnace The modified Andrade furnace is shown in Fig. 1, and the detailed drawing of its construction can be seen in Fig. 2. The furnace proper consists of a 2'/2-in. diam fused silica tube, 20 in. long, which is evacuated continuously at the bottom. Two water-cooled copper electrodes hold the specimen by means of collets held in place in the electrodes by set screws. These electrodes serve also to transmit power to the specimen. The lower electrodes can be clamped to the stand, while the upper electrode is fastened in place to the bellows which in turn is further connected to one side of the lever arm, flexibly supported at the top. After the specimen is mo;nted- and the vacuum is secured, the lever arm is adjusted by means of the counter weight so

Jan 1, 1952

By H. M. Chance

The Choctaw coal-field is a direct westward extension of the Arkansas coal-field, but its coals are not like Arkansas coals, except in the country immediately adjoining the Arkansas line. From the base of the coal-bearing rocks up to the top of the coalmeasures, I find a total thickness of at least 8500 feet. This great mass of coal-bearing rocks consists of an alternation of slates, shales, sandstones and coal-beds, with their accompanying under-beds of fire-clay. Only one small bed of limestone was observed. This occurs near the middle of the series; it is about eighteen inches thick, and quite arenaceous. The formation is naturally subdivided by seven or eight thick beds of sandstone, varying from 50 to 200 feet in thickness, the outcropping edges of which form a series of more or less bold " hogback " ridges, the interbedded shales and slate forming the intervening valleys. The base of the coal-series is a massive sandstone, ranging from 100 to 200 feet or more in thickness, lying immediately beneath the Grady coal-bed, which is the lowest known coal. In the district embraced between. the Missouri, Kansas and Texas railroad and the Arkansas State line, this sand-rock usually forms a bold semi-mountainous ridge. This is the ridge through which the St. Louis and San Francisco railroad passes at Bryan station, where the Grady coal-bed is opened and worked, from which point it can be traced westward without difficulty, passing about three miles north of Le Flor on the same railroad, thence west to the " Little Narrows " (which is merely a gap in the ridge), 'and beyond to a point two miles west of the Thompson-McKinney place, where it swings abruptly north for a mile or more, only to resume immediately its westward course, forming for some miles the northern boundary of the valley known as the " Boiling-Springs Prairie," beyond which it trends somewhat

Jan 1, 1890

By AIME AIME

BEFORE proceeding with the papers scheduled for the ore and foundry session*, the teller's report on the election of officers for the ensuing year was presented, a; follows: Chairman. G.C. F. MacKenzie; vice-chairmen, C.S. Robinson, J. T. MacKenzzie, C. E. Meissner; executive committee, A. L. Field, R. F. Harrington, E. F. Kenney lit. Waterhouse announced that the fall meeting will be devoted to alloy steel. This meeting will be held in Chicago the week of Sept. 22 in connection with the National Metal Congress. He also announced that oxygen in steel will be the central idea of the meeting which will be held in New York next February. The first paper, entitled "Sintering Limonitic Iron Ore at Ironton, Minn.," was presented by Perry G. Harrison (T. P. 284), the author. Sintering was first un¬dertaken in 1024 to treat Cuyuna range iron and manganiferous ores low in silica and high in moisture and containing objectionable qualities of fine... A Dwight-Lloyd machine was first installed. This machine was replaced by a larger one having a width of 72 in. The power cost was decreased from about $11.22 per ton of sinter on a 42-in. machine to about X0.14 for the 72-in. machine. The tons of sinter per man-shift was increased from 11.86 to 16.77. Improvements embodied in the larger plant reduced the cost of sintering to $0.41. The analyses of iron ore and manganiferous ore and the sinter produced from these materials was used to show the increase in value at the mine resulting from sintering. Crude iron ore actually unsalable was increased in value f.o.b. mine from a theoretical figure

Jan 1, 1930

By K. H. Coats

This paper presents the development and solution of a mathematical model for aquifer water movement about bottom-water-drive reservoirs. Pressure gradients in the vertical direction due to router flow are taken into account. A vertical permeability equal to a fraction of the horizontal permeability is also included in the model. The solution is given in the form of a dimensionless pressure-drop quantity tabulated as a function of dimensionless time. This quantity can be used in given equations to compute reservoir pressure from a known water-influx rate, to predict water-influx rate (or cumulative amount) from a reservoir-pressure schedule or to predict gas reservoir pressure and pore-volume performance from a given gas-in-place schedule. The model is applied in example problems to gas-storage reservoirs, and the difference between reservoir performances predicted by the thick sand model of this paper and the horizontal, radial-flow model is shown to be appreciable. INTRODUCTION The calculation of aquifer water movement into or out of oil and gas reservoirs situated on aquifers is important in pressure maintenance studies, material-balance and well-flooding calculations. In gas storage operations, a knowledge of the water movemenr is especially important in predicting pressure and pore-volume behavior. Throughout this paper the term "pore volume" denotes volume occupied by the reservoir fluid, while the term "flow model" refers to the idealized or mathematical representation of water flow in the reservoir-aquifer system. The prediction of water movement requires selection of a flow model for the reservoir-aquifer system. A physically reasonable flow model treated in detail to date is the radial-flow model considered by van Everdingen and Hurst.1 In many cases the reservoir is situated on top of the aquifer with a continuous horizontal interface between reservoir fluid and aquifer water and with a significant depth of aquifer underlying the reservoir. In these cases, bottom-water drive will occur, and a three-dimensional model accounting for the pressure gradient and water flow in the vertical direction should be employed. This paper treats such a model in detail — from the description of the model through formulation of the governing partial differential equation to solution of the equation and preparation of tables giving dimensionless pressure drop as a function of dimensionless time. The model rigorously accounts for the practical case of a vertical permeability equal to some fraction of the horizontal permeability. The pressure-drop values can be used in given equations to predict reservoir pressure from a known water-influx rate or to predict water-influx rate (or cumulative amount) when the reservoir pressure is known. The inclusion of gravity in this analysis is actually trivial since gravity has virtually no efFect on the flow of a homogeneous, slightly compressible fluid in a fixed-boundary system subject to the boundary conditions imposed in this study. Thus, if the acceleration of gravity is set equal to zero in the following equations, the final result is unchanged. The pressure distribution is altered by inclusion of gravity in the analysis, but only by the time-constant hydrostatic head. The equations developed are applied in an example case study to predict the pressure and pore-volume behavior of a gas storage reservoir. The prediction of reservoir performance based on the bottom-water-drive model is shown to differ significantly from that based on van Everdingen and Hurst's horizontal-flow model. DESCRIPTION OF FLOW MODEL The edge-water-drive flow model treated by van Everdingen and Hurst1 is shown in Fig. la. The aquifer thickness b is small in relation to reservoir radius rb. water invades or recedes from the field at the latter's edges, and only horizontal radial flow is considered as shown in Fig. 1b. The bottom-water-drive reservoir-aquifer system treated herein is sketched in Fig. 2a and 2b. Here the aquifer

By Norman Weiss, H. W. Kaanta

CUSTOM ores reach across the New Mexican mesa to American Smelting & Refining Co.'s new lead-zinc mill at Deming. The influx of ores justified increasing mill capacity from 12,000 tons per month to 20,000 tons per month with the installation of a second milling section. Deming mill has met a complex material handling problem with the successful instrumentation of modern machinery and knowledge. A tight, compact plant does a big job with the aid of the latest ore moving equipment. Location and Layout The mill is located three miles northwest of Deming in the tumbleweed covered valley of the Mimbres River, 30 miles north of the Mexican border. Deming has a population of 4000 and is about halfway between Lordsburg and Las Cruces and 54 miles southeast of Silver City. The AT&SF and the SP railroads and U.S. Highways 70, 80, and 260, cut across the mesa to the town. Asarco mill station is east of the AT&SF single track, and north of Deming. The nearly level terrain is covered with fine sand supporting only yucca and tumbleweed. Compacted gravel at depth affords excellent foundation bearing. The climate is semi-arid, but the district is underlain by water-bearing strata. Tailing disposal space is plentiful. The Deming site appeared favorable because of easy rail and highway access, central location in a mining district, excellent climate, plentiful water supply, space for all present and future requirements, and proximity to a town. The milling plant is a 250-ft square. The rail spur forms the west side; sampling plant, fine-ore conveyor and bins are on the east; track hopper, primary conveyor, and crushing plant lie on the south; and the mill building completes the north side of the square. Construction The mill site was chosen and the land purchased in 1,946 and 1947. Design began in 1948, and Stearns-Roger Mfg. Co. of Denver started construction in June 1949 completing work in April 1950. Construction is steel and concrete throughout, with main concrete floors supported on cellular steel beams. The building is covered by galvanized corrugated iron, attached to the frame by welded Nelson studs, and made dust tight at the joints with roofing paper and asphalt sealing compound. Crushing and Sampling Custom ores, delivered to the mill by railroad cars or trucks, are weighed on arrival. A Robbins car shaker dumps the ore into a 100-ton capacity steel hopper. Adjacent is a 40-ton truck hopper. Three 36-in. Pioneer apron feeders supply ore from the receiving hoppers to a 36-in. conveyor which runs to the crushing plant. A tramp-iron detector protects the primary crusher except when handling magnetite containing ores. A 2 ½ -in. spaced grizzly precedes the primary Traylor 24x36 in. jaw crusher set at 4 in. A Symons 4-ft cone crusher in closed circuit with 48x78 in. Robbins Gyrex screen completes crushing to 5/8 in. The discharges of both crushers drop upon a common conveyor, which, after gaining sufficient elevation, transfers ore to a return conveyor. This return conveyor passes under a suspended magnet and over a magnetic head pulley to the Gyrex screen. Screen undersize is conveyed by a 20-in. belt to the sampling plant. Crushing rate varies from 60 to 90 tons per hour. Ores containing magnetite and pyrrhotite nullify the magnetic detector and overload the magnets

Jan 1, 1952

By Samuel Daniels

In this paper are given the mechanical properties, determined by the Engineering Division, Air Service, U. S. A., of the 94 per cent. aluminum, 5 per cent. copper, 1 per cent. silicon alloy as sand-cast and as heat-treated commercially to Air Service Specification No. 11,300. This particular alloy was tested both in the cast and in the heat-treated condition. Tension and tension modulus values were obtained from machined and from un-machined test specimens; while data for shear, compression, impact, torsion, and for Brinell and Rockwell hardness were found from machined bars. Specific-gravity tests were made on sanded, un-machined specimens. The metallography of the alloy is useful as a control to heat treatment and presents some interesting peculiarities in regard to the two iron-bearing compounds. THE demand for an aluminum alloy, suitable for sand castings, that may be heat treated to meet requirements of high strength, ductility, shock and corrosion resistance, and ready machineability has led to the commercial development of a proprietary material that contains from about 4 to 5 per cent. of copper, 1 per cent. of silicon, and such impurities as iron, up to a maximum of 0.75 per cent., and manganese, in quantity usually less than 0.1 per cent.1 Magnesium is not generally present, for it tends to nullify the beneficial influence of the added silicon by forming magnesium silicide. The function of the silicon is to minimize casting difficulties and, structurally, to favor the precipitation of (insoluble) iron-bearing skeletons rather than the needles, which prevent full realization of tensile properties from heat treatment by stimulating intergranular fracture. The amount of silicon necessary to counteract the ill effect of iron is equal to or slightly more than the content of iron; the excess of silicon over this ratio, under certain conditions of heat treatment, enters with CuAl2, the principal hardening constituent, into solid solution and contributes somewhat to the strength of the alloy without appreciably impairing its ductility. The schedule of heat treatment of this alloy depends on the design (cross-sections) of the castings and on the nature of the tensile properties desired. Essentially, the process consists in heating the material at about-950° F., quenching in oil or in cold or boiling water, and artificially aging

Jan 7, 1925

By D. M. Warner, Samuel Daniels

In this paper are given the mechanical properties, determined by the Engineering Division, Air Service, U. S. A., of the 94 per cent. aluminum, 5 per cent. copper, 1 per cent. silicon alloy as 8and-cast and as heal-treated commercially to Air Service Specification No. 11,300. This particular alloy was tested both in the cast and in the heat-treated condition. Tension and tension modulus values were obtained from machined and from un-machined test specimens; while data for shear, compression, impact, torsion, and for Brine11 and Rockwell hardness were found from machined bars. Specific-gravity tests were made on sanded, un-machined specimens. The metallography of the alloy is useful as a control to heat treatment and presents some interesting peculiarities in regard to the two iron-bearing compounds. The demand for an aluminum alloy, suitable for sand castings, that may be heat treated to meet requirements of high strength, ductility, shock and corrosion resistance, and ready machineability has led to the commercial development of a proprietary material that contains from about 4 to 5 per cent. of copper, 1 per cent. of silicon, and such impurities as iron, up to a maximum of 0.75 per cent., and manganese, in quantity usually less than 0.1 per cent.' Magnesium is not generally present, for it tends to nullify the beneficial influence of the added silicon by forming magnesium silicide. The function of the silicon is to minimize casting difficulties and, structurally, to favor the precipitation of (insoluble) iron-bearing skeletons rather than the needles, which prevent full realization of tensile properties from heat treatment by stimulating intergran-ular fracture. The amount of silicon necessary to counteract the ill effect of iron is equal to or slightly more than the content of iron; the excess of silicon over this ratio, under certain conditions of heat treatment, enters with CuAl2, the principal hardening constituent, into solid solution and contributes somewhat to the strength of the alloy without appreciably impairing its ductility. The schedule of heat treatment of this alloy depends on the design (cross-sections) of the castings and on the nature of the tensile properties desired. Essentially, the process consists in heating the material at about 950" F., quenching in oil or in cold or boiling water, and artificially aging

Jan 1, 1926

By Fuller, T. S.

THE number of rare or uncommon elements in use in the electrical industry nowadays is large, their application having come about through investigational work in industrial search laboratories and ' educational institutions. Such elements, together with those whose properties are more generally known, constitute Nature's gift to mankind and make possible the intricate devices which further our modern civilization. The' quality of raiaity is one of degree, and obviously depends largely on one's point of view. From the standpoint of quantity measured in the customary units of weight and volume, the amounts of many of the elements required are extremely small, but from the of view of performing some particular function or .other in a manner more satisfactory or cheaply than can be accomplished by any other sub- stance, the use in question may be extremely important.

Jan 1, 1928