Search Documents

By R. V. Wheeler, W. Francis

Of the methods that have been used for studying the chemical composition of coal, attack by reagents has not, in general, yielded much information. Most of the reagents used have been strong oxidants such as nitric acid or Schulze's solution. The use of a milder oxidizing agent, such as air at low temperatures, enables progressive changes in the character af the coal substance to be studied and thus helps toward an understanding of its constitution. British bituminous coals frequently have a banded structure. These bands (of four types) can be separated one from another and have been found to possess markedly different chemical characteristics, even when taken from contiguous portions of the same lump coal. It has been found convenient to give each of the ingredients of banded coal a distinctive name, more or less descriptive of its appearance, and the study of the chemistry of bituminous "coal" in England has resolved itself into a study of each ingredient separately. The coal chosen for this work was taken from the Top Hard seam at East Kirkby colliery, Nottinghamshire, a detailed chemical analysis of which has been recorded by Baranov and Francis.' The banded structure was well marked and the bands could readily be separated. The research was confined to the brilliant vitreous bands (vitrain), the dull hard bands (durain) and the "sooty partings" main); for previous work had shown that the fourth type, to which the name clarain has been given, is intermediate in character, chemically, between vitrain and durain. The method of experiment was, briefly, to draw a slow current of moist air through weighed samples (50 gm.) of the three ingredients, vitrain, durain, and fusain, in the form of powder (through a 60-mesh and on a 90-mesh sieve) contained in glass tubes which could be maintained at a constant temperature during prolonged periods. After passing through the coal, the air bubbled into a measured volume of

Jan 1, 1925

?AARONSON, ALFRED E , Vice-Pres , Mid-Co Petroleum Co, Mid-Co Bldg, Tulsa, Okla '18 ABADIE, EMILE R, Min Engr Address wanted '76 || ABADILLA, QUIRICO A, Geol Dept, Cia Mexicana de Petroleo "El Aguila," S A, Edifico "El Aguila," Esq, Calles Aurora y Comercio, Tampico, Tamaulipas, Mexico '20 ABBOTT, CLARENCE E, Gen'l Supt, Iron Mines Div, Tenn Coal, Iron & R R Co, 1405 Minnesota Ave, Bessemer, Ala '04 ABBOTT, LOUIS BENJAMIN, Chief Engr, Consolidation Coal Co, Elkhorn Div, Jenkins, Ky '15 ABBOTT, ROBERT R Met Engr, Peerless Motor Car Co, Cleveland, Ohio '12 ABE, ASAKA Fujita Min Co, Dojima, Osaka, Japan '14 ABEEL, GEORGE H, JR, Cons Min Engr, 635 St Paul Ave, Los Angeles, Cal '18 ABEL, ALBERT E, Asst to Pres, Valley Mould & Iron Corpn, Sharpsville, Pea '19 ABEL, W D, Min Engr Forum Bldg, Sacramento, Cal '19 ABELL, O J, Pres & Treas, Abell-Howe Co, 332 South Michigan Ave, Chicago, Ill '19 ABERNATHY G E Willow Springs, Mo '20

Jan 1, 1923

By G. Bruggeman, K. G. Kreider

Grain boundary dij]usion coefficienls were measured in tungsten between 1400° and 2200° C and can be expressed by the equation sq cm per sec This activation energy confirms some eavlier estimates made .from tungsten sintering experiments. Grain boundary diffusion was found to occur in sub-bozrndavies having -misorientations of less than 10 deg. The actiuation energy for this subboundavy diffusion is equal to that for dijjusion in incoherent grain boundaries with in the limits of error. This is shown to be consistent with the dislocation model of Low-angle boundaries wheve diffusion occlcvs along- the dislocation 'YPipes" comprising -tile boundary. RECENT investigations of the sintering of tungsten powders all report activation energies which are considerably less than the activation energy for tungsten volume diffusion. Kothari' reports a value of 100 * 5 kcal per mole, Hayden and Brophy' obtained 90 kcal per mole, and Vasilos and smith3 found 110.7 kcal per mole from their sintering studies. Since most determinations of the activation energy for volume diffu-sion4-' fall between 120 and 160 kcal per mole (the true value seems most likely to be nearer 150 kcal per mole), the conclusion is drawn that the mass transport leading to densification during sintering is accomplished by grain boundary diffusion. This interpretation is consistent with various diffusion models of the sintering process. 10-12 Vasilos and Smith calculate diffusion coefficients from their data which fit the equation D * 1.36 x 10* exp(-llO,700/HD However, no direct measurements of tungsten grain boundary diffusion have been made. Furthermore, considerable disagreement exists between the directly measured values of tungsten volume diffusion.'-' In order to corroborate the inferred results of the sintering experiments concerning grain boundary diffusion and to provide accurate diffusion data essential to the analysis of the kinetics of creep, oxidation, precipitation, and so forth, the present work was undertaken to measure self-diffusion in single-crystal and polycrystalline tungsten between 1400" and 2200°C. It is within this temperature range that tungsten sintering is done, the re crystallization of tungsten occurs, and the widest application of tungsten as a high-temperature material will probably be made. EXPERIMENTAL PROCEDURE Radioactive WlE5 was produced by irradiating tungstic acid in a neutron flux of 1.2 x 1012 neutrons per sq cm per sec for 36 hr. A 2-week waiting period was allowed for the decay of w"~ also produced by the irradiation. (w"~ has a half-life of 24 hr.) The half-life of the remaining isotope was determined to be 75 days confirming the presence of w lE5 and the absence of any undesired radionuclide. Specimens 4 in. in diam and $ in. thick were cut from polycrystalline swaged tungsten rods (recrystal-lized) and from Linde single-crystal rods. Chemical analyses of these materials appear in Table I. Actually upon closer examination, the single-crystal specimens were found to consist of several subgrains separated primarily by tilt boundaries in which the misor-ientation ranged from 3 to 10 deg. Thus, it was possible to measure boundary diffusion coefficients in these low-angle subboundaries as well as in the incoherent boundaries of the polycrystalline specimens. The two faces of each specimen were ground flat and parallel within 0.0001 in. The radioactive tungstic acid was dissolved in concentrated ammonium hydroxide, placed on the ground flat of the specimen, and evaporated to dryness. The oxide was then reduced in hydrogen at 1000°C resulting in a layer of wlE5 approximately 1 p thick. The diffusion anneals were performed in vacuum in a tantalum resistance furnace. Time at temperature ranged from 10 hr at 1400°C to 2 hr at 2200°C. The penetration profile was determined by measuring the residual activity after successive removal of surface layers by grinding on metallographic polishing paper. Extreme care was exercised to insure that sections were always taken normal to the diffusion direction; this was verified repeatedly by checking that front and back surfaces of the specimen remained parallel. The activity was measured with an end-window Geiger-Mueller counter. The sides and edges of the specimen were well-shielded to eliminate possible effects due to surface diffusion. The weight of the

Jan 1, 1968

By R. P. Abendroth

This study is concerned with the kinetics of selective oxidation of chromium in a commercial Fe-Cr-Ni alloy. Selective oxidation of chromium in this alloy, by use of a low oxygen-potential atmosphere, leads to the formation of a compact, protective layer of Cr2O3. This layer serves to protect this alloy from gross scaling when it is subsequently exposed to severe oxidizing conditions at high temperature. The interaction of low oxygen-potential atmospheres close to equilibrium with Fe-Cr and Ni-Cr alloys has been studied by others."' These studies werk concerned with the surface-structure variations under slightly oxidizing conditions. NO detailed study was made of the oxide scale formation kinetics, however. The alloy samples were cut from 0.012-in.-thick sheet, with an apparent surface area of 7.1 sq cm. These sheet samples were abraded through 4/0 metallographic paper, and washed in alcohol and acetone. The analysis of the sheet alloy is (in weight percent): 42 pct Ni, 5.5 pct Cr, 0.09 pct C, 0.18 pct Al, 0.36 pct Si, 0.26 pct Mn, balance Fe. The weight gain vs time data were obtained with a 2-g capacity fused-silica spring—cathetometer system. The spring deflection was optically magnified ten times before being read by the cathetometer. A sensitivity of about 0.01 mg was attainable. The spring was enclosed in a water jacket maintained at 60°C to minimize the effect of temperature changes. The sample was suspended from the spring with a fused-silica hangdown and was positioned in the thermal center of a mullite furnace tube. Sample temperature was read with the aid of a thermocouple placed outside the mullite tube and an inside vs outside temperature calibration. Temperature change during the course of a run was ±0.25°C, with a temperature gradient of less than l.O°C over the length of the sample. Total temperature uncertainty was no more than ±3.0°C. Alignment difficulties between the hangdown and radiation shields in the furnace tube required that the sample be positioned in the furnace when cold, and heated with the furnace until the temperature stabilized at the desired point. This required 5 to 6 hr, and was carried out in Matheson ultrahigh-purity hydrogen. Oxidation was started, after evacuation, by introducing a hydrogen-water vapor mixture, obtained by saturating hydrogen with water vapor at 31.00o ± 0.02oC. Oxidation was continued for 90 min. Gas flow was 300 ml per min during heat up and oxidation. Since only several milligrams of oxide are formed on each sample, chemical analysis of the oxide is difficult. A representative analysis is: 80 pct Cr2O3, 5 pct Fe2O3, 3 pct Al2O3, 4 pct MnO, 7 pct SiO2, 1 pct or less NiO. X-ray diffraction analysis of the oxide as formed on the alloy gives rhombohedra1 Cr2O3, and barely distinguishable amounts of a cubic spinel phase, and possibly AlZOs and SO2. The identification of these latter two compounds is by no means certain. The spinel phase could be based on iron or manganese as these elements are present in significant amounts in the oxide. The results of the kinetic studies using 31°C dew-point hydrogen-water vapor mixtures were found to conform to a parabolic rate law. In many cases the parabolic plot consisted of two intersecting straight lines, defining an early and a late rate for a particular run, and in the other cases the parabolic plot consisted of one straight line for the entire run. The slopes of the various straight lines were determined by the method of least squares. Reproducibility of the data was good enough for multiple runs at the same temperature such that the value given for the rate constant is the average for two or more closely similar values, rather than widely varying values of the rate, where more than one determination is indicated in Table I. The exhibition of only one or of two rate constants during a run can happen at the same temperature. Thus, Table I shows that at 11'74°C a single rate constant was obtained from one sample, while other samples oxidized at the same temperature gave an early and a late rate constant. It should be noted that the single rate constant corresponds very closely with the early rate constant. This is also true at 1153°C. The time at which the late rate started to appear was variable, usually occurring 20 to 40 min after oxidation had started.

Jan 1, 1964

By Charles S. Barrett, Frederick N. Rhines, Robert F. Mehl

The solid solutions which aluminum forms with copper, and with magnesium and silicon, are not extensive, and accordingly could not be expected to form Widmanstatten figures profusely nor with great ease. A study of the Widmanstatten figures in these systems seemed desirable, however, because of the interest which these alloys bear towards age-hardening theories resulting from the necessary relationship between the age-hardening phenomena and the atomic processes leading to the formation of Widmanstatten figures.' Alloys of Aluminum with Copper The most accurate determination of the solid solubi1it.y of copper in aluminum seems to be that by Dix and Richardsoq2 whose results are represented in Fig. 1. According to this work, aluminum dissolves 5.6 weight per cent of copper at 548", and less than one per cent at room temperature. Judging from the constitutional diagram, this solid solu-lion on cooling tends to precipitate the compound CuA12, and this conclusion has been confirmed experimentally by Schmid and Wassermann.

Jan 1, 1932

By Louis J. Demer, Paul A. Beck

As reported in a previous publication,1 isothermal grain growth in high purity aluminum and in an aluminum alloy with 2 pct magnesium can be adequately described by means of the empirical relation: [ ] or in some cases, by the simpler relation, [ ] Here, D is the average grain size after an annealing period t. The annealing period includes the time for complete recrystallization R, and the time for grain growth [to]. DA is the grain size as recrystallized, n is a parameter depending on the temperature and on the material. The effect of 2 pct magnesium in solid solution was to decrease D, and to increase R, A and n at a given temperature. The present work was undertaken in order to investigate the above listed effects of magnesium in solid solution, as functions of the magnesium content. The work also includes the study of certain anomalous effects observed in the recrystallization and grain growth of the 2 pct magnesium alloy at 350°C. EXPERIMENTAL PROCEDURE The method of producing the ingots used in this work was described in detail1 and need not be reproduced here. The materials used were high purity aluminum, furnished by the Aluminum Co. of America, of lot analysis shown in Table I and magnesium from a high purity distilled stock of magnesium crystals. [ ] Ingots were prepared for a series of binary aluminum-magnesium alloys of increasing alloy content. The numbers used to designate these ingots and their magnesium contents by chemical analysis are given in Table 2. [ ] The analyses showed no difference in composition between the top and the bottom of the ingots. Spectrographic analysis of the ingots for elements other than magnesium showed, within the limits of accuracy of the method, no increase in impurities over the amounts given in the lot analysis for the high purity aluminum in Table I. Careful microscopic study of ingot 21 in the as-cast condition, at magnifications up t0 1500X, revealed a cer-

Jan 1, 1948

By B. S. Butler

Introduction. THE New London copper mine, about 81, miles east of Frederick, Md., was visited by the Writers for a few hours in the spring of 1909 and the following brief notes on ore specimens collected are presented as a contribution to studies in chalcocite ores. For certain data on the structural and areal geology of this portion of Maryland the writers are under obligation to the unpublished notes and maps of Arthur Keith. The detailed study of the ores is the work of B. S. Butler. The deposit here discussed has many similarities to those of the Virginia district of Virginia and North Carolina, which have been described y Graton1 and Laney2, except that in the deposits of the New London mine chalcocite is by far the most important ore mineral, while in the Virginia deposits bornite is commonly-the most important sulphide. In the New London occurrence calcite is the most important gangue mineral.

Jan 7, 1914

By John Treweek

FOR many years the Homestake Mining Co. has devoted serious attention to the elimination of accidents, and ground is steadily being gained in this direction. In accident prevention work it is line-plunging with perfect teamwork and not the spectacular forward pass that brings progress toward the goal. In both surface plants and under- ground workings we regard "good housekeeping" as a first requisite for safety as well as efficiency. Under this term are included all types of safety guards and protective devices as well as cleanliness and orderliness it working places. Perhaps the most important factor in safety work is to arouse and maintain employee interest. The general morale and contentment of employees is of particular importance.

Jan 1, 1938

By J. E. Sherborne, P. H. Jones, E. C. Babson

A study of the Chapman zone in the Richfield field, Orange County, California, indicates that the quantity of oil recovered by present methods will be only a small portion of the oil originally in place. Since the volume of residual oil is believed to be of large magnitude, an experimental water-flooding operation has been initiated in order to determine whether water-flooding offers promise as an economical method of recovering some of this residual oil. A single injection well was drilled between old producing wells, and a water-treating plant using alum flocculation and chlorination was designed and built. Water has been injected into the input well for six months at rates in excess of 100 bbl. per day. Production from one of the neighboring wells has increased materially, the oil production having risen from 7 to 30 bbl. and the water From I to 40 bbl. per day. While definite conclusions regarding the economic success of water-flooding in the Chapman zone are not justified at this time, it has been demonstrated that water can be injected into the zone on a sustained basis and that this water will displace appreciable quantities of oil from the sand. Introduction As a result of an investigation of subsurface conditions in the Chapman zone of the Richfield field, it was concluded that ultimate oil recovery from this zone would probably be low and that natural water encroachment was so localized as to be of little importance from a recovery stand- point. Furthermore, it was found that in many portions of the zone the wells were approaching an unprofitable level of production. When these data were presented to the management of the Union Oil Co.; their reaction was that an attempt should be made to develop methods of recovering at least a portion of the large quantity of oil remaining in this zone. After some investigation, it was decided that wafer-flooding offered the most likely means of accomplishing this end, but reservoir conditions in the Chapman zone differ so widely from those encountered in any of the flooding projects described in the literature that it was difficult to evaluate the probability of success. Despite encouraging results from laboratory tests, it was not even certain that water would displace an appreciable volume of oil from the Chapman sand under reservoir conditions. Therefore, it was decided to initiate a small-scale project, for two purposes: first, to determine whether water would displace oil from the Chapmall sand and, second, to obtain information and experience for future operations if water-flooding appeared to be a promising method of secondary recovery. Reservoir Data The Chapman zone is the upper of the two producing zones in the Richfield field, being found at depths from 3000 to 3700 fi.. The productive portion of the zolle consists of a large irregularly shaped sand body, which is more than 400 ft. thick at the top of the structure. As the margin of the field is approached, the sand is replaced

Jan 1, 1945

By A. S. Yue, A. G. Guy

A study was made of the effects of a prolonged flux of zinc atoms through the a solid solution of zinc in copper. The experimental arrangement consisted essentially of a copper disk about 0.01 in. thick, at one of whose surfaces a gaseous atmosphere containing zinc atoms was maintained, and at the other surface a gaseous atmosphere with a minimum of zinc atoms was maintained. During prolonged theothersurfaceexposure at high temperatures the zinc content of the copper disk gradually built up to the steady-state concentration distribution and then remained at this value. The concentration-distribution curves for various conditions were determined by chemical analyses. The results showed that the condition of steady-state diffusion was achieved. The diffusion coefficients calculated from the experimental data, although not of high precision, agreed with the values obtained by other workers using unsteady-state methods. Relatively slight porosity developed in the specimens in the course of diffusion. A LTHOUGH most diffusion studies have been made under unsteady-state conditions, it is known' that the steady-state method is often superior with respect to the directness and accuracy of interpretation of the data. Steady-state diffusion of gases through metal diaphragms is well known. Also, Harris' and Smith" have used the steady-state method in studying the diffusion of carbon in aus-tenite. The accepted mechanism in this system involves the motion of the interstitial carbon atoms in the rigid framework of the lattice of iron atoms. Thus, there is little difficulty in visualizing the steady flow of the small carbon atoms through the austenite. The situation in substitutional diffusion is quite different. Here the atoms are comparable in size, and it is not evident how a steady flow of one of the atoms through the solid solution might be achieved. At the time the present research was started, it was known that a previous exploratory attempt to produce steady-state diffusion in a substitutional alloy, the Au-Ag system,' had been unsuccessful and had indicated that perhaps there were basic difficulties that could not be ovei-come. Therefore, the present research began as a study of the effect of a prolonged flux of metal atoms through a substitutional solid solution. Eventua.lly, it was possible to produce actual steady-state diffusion in the system chosen for study, the a Cu-Zn alloys. Experimental Procedure The aim in the experiments was to maintain a high zinc content, about 30 pet, at one surface of a copper sheet, and to maintain a low zinc content, near 0 pet, at the opposite surface. The zinc would then diffuse into and through the copper, first building up to the steady-state concentration distribution and then maintaining this distribution. The three types of specimens that were used are shown in Fig. 1. In type A specimens the copper disk through which diffusion occurred was welded to the top of a cylindrical molybdenum tube, the bottom of which also was sealed by welding. At the diffusion temperature the brass chips in the molybdenum container were the source of the zinc vapor which maintained the lower surface of the copper disk at 30 pet Zn. The upper surface was maintained at 0 pet Zn by the vacuum in which type A, and also type B, specimens were diffused. Since the molybdenum container was impervious to zinc vapor, it was intended that the only path of escape for the vapor from the brass chips would be through the thin copper diffusion disk. However, it was found that small leaks often developed at the welded joints during the diffusion treatment, and in most specimens some of the zinc was lost in this manner. Although even small losses of this kind were a serious handicap in attempting to determine the flux through the disk, they did not prevent the maintenance of satisfactory boundary conditions for the attainment of the steady-state condition. Type B specimens differed from type A in having a weight of about 300 g supported on the copper disk by 15 to 20 short quartz rods. This change was made when it was observed that the copper disk was being bowed upward by the difference in the pressures acting on its two surfaces. Since the grain-boundary cracking which occurred in the bowed specimens could be attributed largely to the accompanying creep,3 it was desirable to minimize this effect. The counterweight was effective in significantly decreasing both bowing of the disk and cracking at grain boundaries. Type C specimens differed considerably from the others in that the low-zinc atmosphere at one sur-

Jan 1, 1959

By A. L. Blomfield

THE Golden Cycle Mining and Reduction Co. operates its custom mill at Colorado Springs on Cripple Creek ores exclusively. These ores are straight sulpho-tellurides, with practically no base metals such as Pb, Cu, Zn, As, or Sb. Upon entering the mill, the ore all passes through the sampler to storage bins, where beds of 5000 tons each are made to insure uniformity in roasting. CLASSIFICATION OF ORES For efficiency, it has been found advisable to separate the ores into two classes according to their line content. Other constituents have their effect, such as alumina and magnesia, but, speaking generally, these are roughly proportional to the line, which, as CaO, is used as the indicator. Class A contains not more than 2 per cent. CaO and comprises about 66 per cent. of the ore treated. Class B contains over 2 per cent. CaO, and comprises 34 per cent. of the ore treated. Typical analyses of both classes are as follows: Class A Class B Insol 56.70 75.90 Al203 2.30 3.40 Fe 3.26 3.48 CaO 1.57 5.12 S 1.79 1.80 Mg0 0.21 1.08 Ignition loss 3.20 6.50 99.03 97.28 The beds of each class of ore are made as large as possible with the available ore as it comes in, to avoid changing from one bed to the other any oftener than necessary. Each roaster will handle 50 percent. more of class A ore than of class B, with practically the same results. This necessitates changing the rate of feed for each new bed and tends toward a poor roast and loss of tonnage at each change.

Jan 8, 1918

By AIME AIME

THE 1944 Chairman of the Institute of Metals Division might be classed as metallurgically ambidextrous ; he is teacher of theory and practice of both nonferrous and ferrous metallurgy, and he is consultant on brass and on highspred steel. Arthur Phillips was born in Troy N.Y. and attended the New Haven Connecticut high school. Upon graduation he entered Yale, receiving a degree in metallurgy in 1913. At that time Professor Mathewson was starting his plan of '"co-operation with the metal industries in metallographic work at the Hammond Laboratory of the Sheffield Scientific School, Yale University, and Arthur Phillip, became the first co-operative graduate student, working in the laboratory of the Bridgeport Brass Co., and receiving his Masters of Science degree in 1915. A little later, when the department of metallurgy at Yale was expanded. Me. Phillips was appointed assistant professor. In 1928 he was made associate professor, and in 1934 he was promoted to full professor.

Jan 1, 1944

By H. F. Winham

THE history, development, subsurface geology, production, economics and estimated reserves are discussed in this paper. The Magnolia structure is an anticline with a known maximum structural relief at 372 ft., and the areal extent of the producing acreage is 4494 acres. Production is obtained from the Smackover oölitic lime and 116 successful wells have been drilled. The field, which was developed on 4o-acre spacing, has been under strict control. It is believed to be producing with a strong water drive. To date it has produced more than eighteen million barrels and the estimate of ultimate recovery is 220 million barrels. EARLY HISTORY The Magnolia field is in Columbia County, Arkansas, T. 17 S., R. 19 and 20 W. Various geologists had long been interested in this general area, and as early as 1921, John F. Magale was able to define a surface structure. The first wildcat, one of the first in Columbia County, was drilled in 1923 by Mid-States Oil Co., in sec. 10, T. 17 S., R. 20 W. This well was about 1 ½ miles northwest of the Kerlyn Oil Company's discovery well and was based on surface geological work done by jewel and Dobie. Subsequently, several shallow wells that were not carried below the Upper Cretaceous beds were drilled in the immediate area of the discovery well, but none of them contained any commercial showings of oil or gas. In the latter part of 1935, Elam and Magale (or Southwood) Garrett No. I was located in sec. 13, T. 17 S., R. 20 W., ¾ mile east of the discovery well. It was drilled to a total depth of 4018 ft. in the lowermost Glen Rose beds but failed to obtain any showings of oil or gas. Interest had been stimulated in this general area, however, by the discovery of several oil fields, mainly Glen Rose oil production in the Rodessa field in Louisiana in 1935, Smackover lime production in Snow Hill in May 1936, production from the Cotton Valley formation in Schuler in 1037, and Smackover lime production from the Buckner field in November 1937. With this background and subsequent seismic work, which was carried on partly because the old shallow wells drilled in the township had shown evidence of closure in the Upper Cretaceous beds, the discovery well, Kerlyn Oil Company's Barnett No. I, sec. 14, T. 17 S., R. 20 W., was originally projected to a total depth of 6300 ft., to test the equivalents of the Morgan sands of the Cotton Valley series, then producing at Schuler. The well was carried to a total depth of 6325 ft. and tested the objective beds without finding commercial production. In the meantime, however, one well had found production in the Jones sand and another in the Smackover lime at Schuler. Kerlyn immediately made arrangements to deepen the Barnett well to the Smackover lime. The top of the Smackover lime was encountered at 7618 ft. and the well was cored and drilled to a depth of 7740 ft.

Jan 1, 1942

By AIME AIME

THE convention which met in Washington at the call of the Joint Conference Committee was called to order at ten o'clock on Thursday morning; June 3, by Richard L. Humphrey, temporary chairman, member of the American Society of Civil Engineers, who made a brief statement of the reason for the meeting. Lieut. Col. Charles W. Kutz, Corps of Engineers, U. S. A., and Engineer Commissioner of the District of Columbia, then welcomed .the engineers composing the convention on behalf of the District of Columbia and, the Washington engineers. Although an elaborate program had been prepared on which were many well-known speakers on interesting and important topics, , it was voted to intersperse this to fill in the usual and unavoidable hiatuses in the business program of such a convention[ Calvert Townley, president of the American Institute of Electrical Engineers, was elected permanent chairman, and J. C. Hoyt, of Washington, was elected secretary of the convention. The following committees were appointed: Consti¬tution and by-laws, Richard L. Humphrey, chairman; resolutions, Philip N. Moore, chairman; and program, F. H. Newell, chairman. Then, Gardner S. Williams, member of the, A. S. C. E. and the Grand Rapids Engineering Society of. Grand Rapids, Mich., and one-time member of the American Association of Engineers, offered the following resolutions:

Jan 1, 1920

By MARSHALL D. DRAPER

CHINA is one of the large producers of the world's tin. About 95 per cent of the total Chinese production comes from the Kotchiu district in the southern part of the province of Yunnan. Yunnan occupies the southwestern part of China, bordering on Burma,. Siam and. French Indo-China. From the British port of Hong Kong,' small steamers sail southwest at about four-day intervals, reaching Haiphong in French Indo-China in two or three days. This, one of the principal ports in Indo-China, is a modern French city of some 50,000 population which, with its tropical surroundings, has much natural beauty. It is a few miles from the sea on the Red River, which has its source in China. Both at Haiphong and Hanoi, the capital of Indo-China, sixty-three miles north of Haiphong and also on' the Red River, there are foundries, shipyards, machine shops, cement and brick plants and various similar industries.

Jan 1, 1931

By AIME AIME

THE climax of the various programs and entertainments in connection with the holding of the World Engineering Congress* in Tokyo in October was the complimentary dinner given by the visiting members of the Institute to our members in Japan. At the same time President Bradley conferred an honorary membership on Baron Takuma Dan, the vice-president of the World Engineering Congress.

Jan 1, 1930

By Victor Rudenno

Feasibility studies for mining projects traditionally involve in their final stages a lengthy process of repetitive trial and error discounting, in calculating the discounted cash flow rate of return resulting from the respective yearly after-tax cash flows. Also, probability analysis and sensitivity analysis (in particular) require extensive additional calculations with each change of any project parameter . These inefficient repetitive procedures have two unacceptable results: 1. they are not flexible enough to allow ready analysis of dependent parameters , and 2. they require resort to high-capacity centralised computing facilities with their inherent impersonality, rather than a convenient and available desk calculator - a factor of particular importance to top mining management. Such problems can be overcome if the mining project can be represented by a reasonable straightforward mathematical economic model. The most flexible and appropriate model has been found to be one in which a maximum and minimum value for each of n parameters are supplied to a program which determines a large number of systematic combinations of parameter events and then statistically analyses them to determine the resulting coefficients of the model. In this paper the authors discuss the selection of the most appropriate type of model and outline the steps followed in its development and application.

Jan 1, 1977

By R. R. Estill

THE rank of the Ruhr coal ranges from a high volatile bituminous coal to an anthracite, depending to some extent on the original depth of the seam. The average Ruhr coal corresponds to a soft bituminous American coal of a coking quality. The average thicknesses of individual coal seams being mined are also comparable (59 in. against 65 in. in the United States). However, consideration of seam conditions and mining conditions other than those just mentioned emphasizes differences rather than similarities with United States soft coal. In general, the Ruhr seams now being mined are much more folded and inclined than American seams. Dips of 20' and 30" are common in seams now being worked, and 30 pct of the coal reserves in the district are in seams dipping more than 35". Only on the tops and bottoms of folds do we find rather flat coal seams. In addition to the folding there is extensive displacement by cross faulting plus a certain amount of strike faulting of an overthrust nature, which results locally in doubling or omission of seams. Because of the long history of mining in the Ruhr, nearly all coal lying near the surface has long since been mined out, and we find that the average depth of mining is at present about 2300 ft below the surface. Deep mining, folding, and faulting result in seam conditions requiring a great deal more roof support than one finds in American soft coal mines. In fact only in the anthracite district and the Rocky Mountain and Pacific coal fields do we find somewhat similar conditions. It is easy to say, therefore, that the problem of mechanization of coal cutting and loading in the German mines is quite different from that which we have so effectively met in America with our mobile cutters and loaders, duck bill loaders, and a room and pillar system of mining our drift and slope mines. Partly because of more limited coal reserves, the traditional German mining system is largely the longwall method, which gives an almost complete coal recovery. Backfilling must be extensively practiced to protect the longwall faces, the over and underlying seams and workings, and especially the surface industrialized areas and barge canals. The German engineers have accordingly concentrated their efforts on the design of cutters, loaders, and conveyors suitable to longwall methods rather than room and pillar methods. Undercutters with cutter bars like American models have been in use in the Ruhr since well before World War 11. In 1941 they accounted for 8.5 pct of the production. This percentage, of course, includes coal which was undercut but nevertheless had to be broken down with air hammers or with explosives. The most common of these cutters is the Eickhoff Standard cutter (see fig. 1). This machine does about 95 pct of the undercutting in the Ruhr today, and is available with either compressed air or electrical power and in at least four different sizes. A variation of the cutter is this one with two cutter bars (fig. 2). At the end of 1947 about 200 of these machines and similar cutters were accounting for 13.2 pct of the total production, a production which was, however, only 60 pct of the 1941 production rate, so that the actual cutter tonnage was only up to a small amount over 1941. In 1941 about 3 pct of the production was accounted for by shearing machines making their cut perpendicular to the longwall face. They were similar to those used in the States. These machines are today considered obsolete and now account for only 0.7 pct of the total production. They are located at only a few mines and at present do not seem to have much of a future in the Ruhr. For the future, the Ruhr miner is looking forward to rather extensive mechanization of face work, with two major types of equipment being developed almost simultaneously. On one hand there is the development of cutter loaders for use in relatively hard coal. They represent the further extension of ideas developed after relatively long experience with the Eickhoff cutter. On the other hand there has been since 1942 an intense interest in the Ruhr in the development of face-stripping methods, particularly by the Kohlenhobel (coal plow) and its modification. At the end of 1947 these cutter loaders, Kohlen-hobels and scrapers together were actually accounting for only about 1.4 pct of total production while air hammers still broke 77.1 pct and as much as 1.2 pct was actually broken by hand picks. However,

Jan 1, 1951

By R. R. Estill

THE rank of the Ruhr coal ranges from a high volatile bituminous coal to an anthracite, depending to some extent on the original depth of the seam. The average Ruhr coal corresponds to a soft bituminous American coal of a coking quality. The average thicknesses of individual coal seams being mined are also comparable (59 in. against 65 in. in the United States). However, consideration of seam conditions and mining conditions other than those just mentioned emphasizes differences rather than similarities with United States soft coal. In general, the Ruhr seams now being mined are much more folded and inclined than American seams. Dips of 20' and 30" are common in seams now being worked, and 30 pct of the coal reserves in the district are in seams dipping more than 35". Only on the tops and bottoms of folds do we find rather flat coal seams. In addition to the folding there is extensive displacement by cross faulting plus a certain amount of strike faulting of an overthrust nature, which results locally in doubling or omission of seams. Because of the long history of mining in the Ruhr, nearly all coal lying near the surface has long since been mined out, and we find that the average depth of mining is at present about 2300 ft below the surface. Deep mining, folding, and faulting result in seam conditions requiring a great deal more roof support than one finds in American soft coal mines. In fact only in the anthracite district and the Rocky Mountain and Pacific coal fields do we find somewhat similar conditions. It is easy to say, therefore, that the problem of mechanization of coal cutting and loading in the German mines is quite different from that which we have so effectively met in America with our mobile cutters and loaders, duck bill loaders, and a room and pillar system of mining our drift and slope mines. Partly because of more limited coal reserves, the traditional German mining system is largely the longwall method, which gives an almost complete coal recovery. Backfilling must be extensively practiced to protect the longwall faces, the over and underlying seams and workings, and especially the surface industrialized areas and barge canals. The German engineers have accordingly concentrated their efforts on the design of cutters, loaders, and conveyors suitable to longwall methods rather than room and pillar methods. Undercutters with cutter bars like American models have been in use in the Ruhr since well before World War 11. In 1941 they accounted for 8.5 pct of the production. This percentage, of course, includes coal which was undercut but nevertheless had to be broken down with air hammers or with explosives. The most common of these cutters is the Eickhoff Standard cutter (see fig. 1). This machine does about 95 pct of the undercutting in the Ruhr today, and is available with either compressed air or electrical power and in at least four different sizes. A variation of the cutter is this one with two cutter bars (fig. 2). At the end of 1947 about 200 of these machines and similar cutters were accounting for 13.2 pct of the total production, a production which was, however, only 60 pct of the 1941 production rate, so that the actual cutter tonnage was only up to a small amount over 1941. In 1941 about 3 pct of the production was accounted for by shearing machines making their cut perpendicular to the longwall face. They were similar to those used in the States. These machines are today considered obsolete and now account for only 0.7 pct of the total production. They are located at only a few mines and at present do not seem to have much of a future in the Ruhr. For the future, the Ruhr miner is looking forward to rather extensive mechanization of face work, with two major types of equipment being developed almost simultaneously. On one hand there is the development of cutter loaders for use in relatively hard coal. They represent the further extension of ideas developed after relatively long experience with the Eickhoff cutter. On the other hand there has been since 1942 an intense interest in the Ruhr in the development of face-stripping methods, particularly by the Kohlenhobel (coal plow) and its modification. At the end of 1947 these cutter loaders, Kohlen-hobels and scrapers together were actually accounting for only about 1.4 pct of total production while air hammers still broke 77.1 pct and as much as 1.2 pct was actually broken by hand picks. However,

Jan 1, 1951

By Robert Bell

The Tar-Sands" is the name which has been given to the extensive horizontal deposit of fine Cretaceous sand, blackened by tarry petroleum, which forms the banks of the last or lowest 130 miles of' the Athabasca river before it terminates in Athabasca lake. The Cretaceous strata, to which these sands belong, extend northwesterly from Dakota all the way to this lake and for 500 miles beyond it. The Athabasca river forms the uppermost section of the Athabasca-Mackenzie, one of the great rivers of the world. It rises on the Pacific side of the Rocky mountains, westward of Edmonton, and flows north of east to a point called Atha-basca Landing, 100 miles north of Edmonton, where it turns northward and runs about 280 miles before it falls into the west end of Athabasca lake. The section of this river-system which discharges the lake just named into Great Slave lake, is called Slave river, and below the latter lake it becomes the Mackenzie river. Along the section of 280 miles of the Athabasca river above mentioned, the Cretaceous strata consist of bluish-gray and drab-gray marls, on top, from Athabasca Landing to Drowned rapid, 110 miles down stream; then heavily bedded gray sandstones, 225 ft. in greatest thickness, underlying these, form the banks for about 40 miles further. The strata appear to be horizontal, but they really dip very slightly to the southward. At Drowned rapid, we see the first of the tar-sands resting on almost horizontal beds of bluish-gray limestone of Devonian age. In some places the limestone is associated with shaly or marly bands. Notwithstanding the great hiatus between the two series, the horizontal tar-sands lie conformably upon the almost level upper beds of the limestone wherever the two formations are seen together, all along the river, throughout a

Jan 1, 1908