Search Documents

By James J. Bean

HE task of measuring the specific gravity of the -*- operating medium in a heavy-media separation system has never presented a particularly difficult problem because the medium is fairly stable and the overflow of the separatory vessel, as well as its underflow, can be sampled easily and accurately and the specific gravity of the suspension determined easily by weighing a known volume. However, while this method is simple and accurate it does require the operator to take the sample by hand and to weigh it and there is considerable temptation to avoid the periodic sampling if everything seems to be going well, or if something is occupying the attention of the operator. Furthermore all operators do not sample in exactly the same manner and considerable practice is required for two operators to be able to "check" each other to the last few hundredths, particularly if the sample is cut underneath the drainage screen where location of the point of sampling and load on the screens tends to influence the determination. While none of the above presents much of a problem, we have all recognized that some mechanical method of continuous measurement and recording would be advantageous since the operator would merely have to glance at the meter to check the gravity and to have an indication of the trend of any changes. Also if the instrument were of the recording type, a permanent record would be available for the guidance of the superintendent. The Eagle-Picher Mining and Smelting Co. was the first heavy-media user to actually install such a recording meter. In 1946 they installed in their Central Mill at Cardin, Okla., a specific gravity recorder manufactured by the Bristol Co. of Water-bury, Conn. R. A. Barnes, of the Bristol Co., working with E. H. Crabtree, Jr. and Elmer Isern, of Eagle-Picher, made the application and worked out the problems of sampling and measuring. Their attempts to measure the specific gravity of the medium in the cone itself were not entirely successful and they resorted to an outside sample tube for actually making the determination. Because of the particular flowsheet used, it was possible to tap off from the medium return pipeline a stream of medium and divert it into the sampling tube, which was provided with a constant level overflow and a spigot underflow, and into which the bubbler tubes dipped. The Eagle-Picher installation was successful and its possibilities were recognized by the Mineral Dressing Laboratory of the American Cyanamid Co. It was decided to install a similar unit in the heavy-media pilot plant to investigate further its possibilities. Chief among these was the continuous record which it was felt would be proof of the steadiness of the gravity in a heavy-media cone, something which is not always appreciated by POtential users. Because the heavy-media pilot plant is required to operate at a wide range of specific gravities, it was realized that the unit would have to record all gravities from 1.25 to 3.50, and do it to the nearest 0.01. It would not be necessary to record all of this wide range on a single chart and the method selected was to have 4 bands, each band range overlapping the other a small amount and calibrated so that with standard charts one division would represent 0.01 sp gr. A shift from one band to another could be arranged without alteration of the instrument itself, being accomplished by a simple change in the bubble-tube lengths, as described later. Accordingly, a recording type instrument was purchased and installed. Because there were some advantages in doing so, the first installation attempted to measure the gravity of the cone proper by placing the bubble tubes in the cone. This was not at all satisfactory and the second scheme utilized a fixed vertical screen at the surface of the cone, and an external sample-tube arrangement. We were particularly anxious to make this work as we felt it would be advantageous to measure the top level of medium where the separation was actually being made, but we were doomed to disappointment because it was impossible to keep the screen clean of float. Since the top gravity of the cone is the most convenient place to sample for control, a launder about 2 in. wide was installed longitudinally beneath the

Jan 1, 1951

By James J. Bean

HE task of measuring the specific gravity of the -*- operating medium in a heavy-media separation system has never presented a particularly difficult problem because the medium is fairly stable and the overflow of the separatory vessel, as well as its underflow, can be sampled easily and accurately and the specific gravity of the suspension determined easily by weighing a known volume. However, while this method is simple and accurate it does require the operator to take the sample by hand and to weigh it and there is considerable temptation to avoid the periodic sampling if everything seems to be going well, or if something is occupying the attention of the operator. Furthermore all operators do not sample in exactly the same manner and considerable practice is required for two operators to be able to "check" each other to the last few hundredths, particularly if the sample is cut underneath the drainage screen where location of the point of sampling and load on the screens tends to influence the determination. While none of the above presents much of a problem, we have all recognized that some mechanical method of continuous measurement and recording would be advantageous since the operator would merely have to glance at the meter to check the gravity and to have an indication of the trend of any changes. Also if the instrument were of the recording type, a permanent record would be available for the guidance of the superintendent. The Eagle-Picher Mining and Smelting Co. was the first heavy-media user to actually install such a recording meter. In 1946 they installed in their Central Mill at Cardin, Okla., a specific gravity recorder manufactured by the Bristol Co. of Water-bury, Conn. R. A. Barnes, of the Bristol Co., working with E. H. Crabtree, Jr. and Elmer Isern, of Eagle-Picher, made the application and worked out the problems of sampling and measuring. Their attempts to measure the specific gravity of the medium in the cone itself were not entirely successful and they resorted to an outside sample tube for actually making the determination. Because of the particular flowsheet used, it was possible to tap off from the medium return pipeline a stream of medium and divert it into the sampling tube, which was provided with a constant level overflow and a spigot underflow, and into which the bubbler tubes dipped. The Eagle-Picher installation was successful and its possibilities were recognized by the Mineral Dressing Laboratory of the American Cyanamid Co. It was decided to install a similar unit in the heavy-media pilot plant to investigate further its possibilities. Chief among these was the continuous record which it was felt would be proof of the steadiness of the gravity in a heavy-media cone, something which is not always appreciated by POtential users. Because the heavy-media pilot plant is required to operate at a wide range of specific gravities, it was realized that the unit would have to record all gravities from 1.25 to 3.50, and do it to the nearest 0.01. It would not be necessary to record all of this wide range on a single chart and the method selected was to have 4 bands, each band range overlapping the other a small amount and calibrated so that with standard charts one division would represent 0.01 sp gr. A shift from one band to another could be arranged without alteration of the instrument itself, being accomplished by a simple change in the bubble-tube lengths, as described later. Accordingly, a recording type instrument was purchased and installed. Because there were some advantages in doing so, the first installation attempted to measure the gravity of the cone proper by placing the bubble tubes in the cone. This was not at all satisfactory and the second scheme utilized a fixed vertical screen at the surface of the cone, and an external sample-tube arrangement. We were particularly anxious to make this work as we felt it would be advantageous to measure the top level of medium where the separation was actually being made, but we were doomed to disappointment because it was impossible to keep the screen clean of float. Since the top gravity of the cone is the most convenient place to sample for control, a launder about 2 in. wide was installed longitudinally beneath the

Jan 1, 1951

Coal Transport Via Pipe Line Claimed Feasible Moving coal via pipe line is a project proposed by the U. S. Bureau of Mines. A pipe line 100 miles long capable of transporting 5000 tons of coal a day with water could be built for about $10 million. The cost of moving the coal 100 miles would be between $1.28 and $2.01 a ton.

Jan 9, 1951

By A. U. Seybol

Eight binary iron alloys were examined after ion nitriding experiments to determine the behavior of the following elements: Al, Mo, Mn, Si, Ti, V,Cr, and C. Only Al, Cr, Ti, and V additions caused hardening in binary iron alloys. A few steels were examined to see the effect of Cr, Cr + Al, Cr + Ti, and Cr + V. It is suggested that a useful new class of ni-triding grade steels might be those containing about I pct V. The nitriding of steel, first described by Fry1 about 45 years ago, rapidly attained commercial application with very little knowledge of the fundamentals involved. While Fry,' in describing the status of nitriding in 1932, apparently correctly postulated hardening by precipitated nitrides, the details of the nitriding process were not understood, nor has the situation changed much since that time. It is also interesting to note that the compositions of some typical nitriding steels given by Fry at that time have changed little in the intervening years. Currently used nitriding steels owe their surface hardening to either chromium (as in 4340 steel) or aluminum plus chromium as in the Nitralloy grades, where both CrN and AlN appear to contribute to harden ing. Titanium additions have been studied experimentally, but thus far titanium steels have not won wide commercial acceptance. This subject will be expanded later. The orthodox ammonia nitriding process has been reviewed very adequately many times as in Jenkins3 and Case and VanHorn,4 and their is no need to outline the process here. Ion nitriding is not as well-known, although there have been several descriptions5-9 of the process given, sometimes with comparisons with the ammonia process. Most of these papers are primarily concerned with a description of the equipment, or of the physics or electrical engineering aspects of ion nitriding, but Noren and Kindbom9 gave the results of a metallurgical investigation using both processes. In brief, ion nitriding is carried out in a vacuum chamber from which the air is exhausted and replaced by a N2-H2 mixture, typically containing 10 to 20 pct N2, at about 5 to 10 torr pressure. While ammonia gas has also been used in ion nitriding, there is no evidence that ammonia makes any improvement in the ion nitriding process. A few hundred volts dc is applied between the grounded container wall (positive) and an insulated center post supporting the work (negative) to be nitrided. A glow discharge is created in the ionized gas, accelerating positive nitrogen ions to the work. These ions contain enough energy to form the normally unstable Fe4N "white layer", thus establish- ing surface nitrogen solubility characteristic of the a Fe/Fe4N equilibrium. This creates a substantial concentration gradient, driving dissolved nitrogen into the steel. The temperature employed is in the same range (around 500" to 550°C) as in ammonia nitriding, but because of factors which are not understood at present the nitriding time is ordinarily considerably reduced in ion nitriding. Other advantages have been cited,9 but it is not the purpose of the present work to contrast the two processes. The present objective was to examine the behavior of binary iron alloys during ion nitriding with respect to the microstructure, hardness level, and depth, and to examine some of these factors in steels as well. In this way it was hoped to be able to find out something about the individual role of these elements in steels. While all the work was done by ion nitriding, there seems to be no reason why any conclusions reached would not equally apply to ammonia nitriding, excepting only the kinetic aspects of the process. Another objective was an exploration of the critical-ity of the ion nitriding variables: gas composition, pressure, temperature, and time. EQUIPMENT AND MATERIALS The equipment used was substantially as described by Jones and Martin.8 The vacuum tank was about 12 in. in diam by about 18 in. high, and consisted of water-cooled stainless steel, with a single small window at the top for viewing inside. This sat on a heavy mild steel base equipped with the main pumping port, pressure control port, and vacuum gaging. A series of variable resistances was interposed between the glow discharge and a large-capacity -40 amp variable primary transformer feeding a 1000-v transformer, but 600 v were about the maximum ordinarily used. With the small l-in.-round, 4-in.-thick discs used for nitriding, the electrical load was usually about 500 v at 0.8 amp. The specimen temperature was controlled by a stainless-steel sheathed chromel-alumel couple, whose junction was in the steel stool upon which the flat discs were placed. These were ground through 400 Sic paper. Cycling of the temperature controller caused -0.2 amp variation in ion current, providing an ample control band. The binary iron alloys were made from vacuum-melted hydrogen-deoxidized electrolytic iron and alloys of 99.9 pct purity. Cast ll-lb-square tapered ingots were forged and hot-rolled to about 11/4-in.-diam rounds. Discs of 1/4 in. thickness by about 1 in. diam were machined from the rods for nitriding specimens. The following alloys were prepared: 1 pct each of Mn, Mo, Cr, Ti, Al, V, Si, and an Fe-0.8 pct C alloy. EXPERIMENTAL VARIABLES Of the variables total gas pressure, nitrogen partial pressure, temperature, and time, only nitrogen partial pressure was found to be critical to the operation. A critical nitrogen partial pressure was found corre-

Jan 1, 1970

By A. R. Kinkel

The Shasta copper-zinc district of northern California lies in the foothills of the Klamath Mountains at the northern end of the Sacramento Valley. It contains two main areas of base-metal ore deposits, the East Shasta and West Shasta districts shown in Fig. 1. The East Shasta includes the area from the Afterthought mine, near the settlement of Ingot on U. S. highway 299 East, to the Bully Hill mine, on the north side of the Pit River, 9 miles to the north- west. The West Shasta, a well-defined northeast- trending district about 8 miles long and 2 miles wide, west of the Sacramento River, Fig. 2, is the western part of the ore-bearing area formerly known as the Shasta copper belt. Referred to in the older writings as a copper arc, this belt was thought to form a crescent extending entirely around the head of the Sacramento Valley, the convex side to the north. Recent studies by the U. S. Geological Survey in cooperation with the California State Division of Mines show that there are two districts, one at each end of the so-called copper arc, which are distinct in geologic structure and ore occurrences, and that there is only sporadic and unconnected copper mineralization between them.

Jan 2, 1955

By John M. Hartman

On May 19th, 1857, an English patent was granted to E. A. Cowper for heating air or other gases under pressure by means of a regenerator inclosed in an air-tight iron case, having between the regenerator and case a lining of brick. This patent provided for heating the stoves by a separate fireplace, or by gas direct from the blast furnace. A number of forms of interior arrangement of the brickwork are shown in the drawings; also hollow poppet valves with hollow stems, and a pipe inside of the stem for circulating the water; the valve seats have coil cast in them for water circulation to keep them cool; slide valves, with snake coil cast in the discs, are shown, and the use of cold air for cooling the valves is also described. The combustion-chamber of these stoves was central, and openings mere provided at the top and bottom to get into the stoves. These Cowper stoves are all circular in section. November loth, 1865, an English patent was granted to Thomas Whitwell for regenerative stoves for heating air or gas, provided with cleaning openings at the top and bottom capable of being closed with firebrick plugs and doors. The drawings show a rectangular stove inclosed in an iron case. The interior brickwork has numerous upand-down passages through the stove, but there is no claim on the interior construction. March 3d, 1868, an English patent was granted to Charles Cochrane for a slide valve to be subjected to high heats. The disc of this valve was hollow, and had a circulation of water through it by the two hollow stems that operated it. The valve-seat was detachable and had a coil cast in it, through which water circulated. The valve and seat were placed on an incline to the body to cause the valve-disc to lie on the valve-seat. A cap was placed on the bottom of the body to get at the interior readily. January 5th, 1870, an English patent was granted to Siemens, Cowper and Cochrane for the construction of regenerators in firebrick stoves, with numerous vertical passages of sufficient size to allow a brush to pass through and clean them. These passages had slight projections on the sides to tarn the air over and over as it passed through. A claim also covered the use of horizontal passages connected at each end alternately, and the use of blasts or jets of air,

Jan 1, 1880

By Joan M. Hartman

ON May 19th, 1857, an English patent was granted to E. A. Cowper for heating air or other gases under pressure by means of a regenerator inclosed in an air-tight iron case, having between the regenerator and case a lining of brick. This patent provided for heating the stoves by a separate fireplace, or by gas direct from the blast furnace. A number of forms of interior arrangement of the brickwork are shown in the drawings; also hollow poppet valves with hollow stems, and a pipe inside of the stem for circulating the water; the valve seats have coil cast in them for water circulation to keep them cool; slide valves, with snake coil cast in the discs, are shown, and the use of cold air for cooling the valves is also described. The combustion-chamber of these stoves was central, and openings were provided at the top and bottom to get into the stoves. These Cowper stoves are all circular in section. November 10th, 1865, an English patent was granted to Thomas Whitwell for regenerative stoves for heating air or gas, provided with cleaning openings at the top and bottom capable of being closed with firebrick plugs and doors. The drawings show a rectangular stove inclosed in an iron case. The interior brickwork has numerous up-and-down passages through the stove, but there is no claim on the interior construction. March 3d, 1868, an English patent was granted to Charles Cochrane for a slide valve to be subjected to high heats. The disc of this valve was hollow, and had a circulation of water through it by the two hollow steins that operated it. The valve-seat was detachable and had a coil cast in it, through which water circulated. The valve and seat were placed on an incline to the body to cause the valve-disc to lie on the valve-seat. A cap was placed on the bottom of the body to get at the interior readily. January 5th, 1870, an English patent was granted to Siemens, Cowper and Cochrane for the construction of regenerators in fire-brick stoves, with numerous vertical passages of sufficient size to allow a brush to pass through and clean them. These passages had slight projections on the sides to turn the air over and over as it passed through. A claim also covered the use of horizontal passages connected at each end alternately, and the use of blasts or jets of air,

Jan 1, 1880

By C. M. Young

Wherever salt is extracted from the ground as an artificial brine produced by pumping down fresh water to dissolve the salt, subsidence of the overburden is a possibility, though apparently few cases of such subsidence have been noted and detailed records are wanting. This description is intended as a record of subsidence that may permit the forcasting of similar occurrences in other cases; the data were supplied largely by R. B. Lee, city engineer of Hutchinson, Kans. About eleven years ago, ground movement occurred at a neighboring salt plant, when the surface assumed the form of a shallow funnel. Movement was probably due to a flow of sand into a well through a poor seal or a broken casing. The salt deposit increases in thickness from the east until at Hutchinson, where the subsidence occurred, it is about 310 ft. thick. The interbedded layers of shale vary in thickness from mere traces to about 7 ft. While knowledge of the shale content of the beds is not exact, the log of a shaft 3 miles east of Hutchinson indicates that shale forms about 25 per cent. of the total thickness. This shaft does not reach the bottom of the salt by about 60 ft., but there is no reason to think that the lower part of the bed is different from the upper. Logs of wells sunk to the bottom are not sufficiently detailed to be of much value. Above the salt is the shale of the well-known Red Beds. The thickness of this is variable, principally because of its eroded surface, but at the mine it is 340 ft. This shale is variable in character and strength, but contains no strong members of limestone or sandstone. If the support is removed, very probably it will subside. The Arkansas River flows across the salt district and Hutchinson is situated on the flood plain. Between the top soil, which is about 8 ft. thick, and the shale is 60 to 100 ft. of water-bearing sand and gravel. The process of removing salt, at least in the case of the earlier wells with which we are concerned, is as follows: An 8-in. hole is put down through the sand and gravel by means of a drive pipe, which is bedded in the shale. Prom the top of the shale, a 6411. hole is drilled through the shale, to, or nearly to, the bottom of the salt. Casing is put in to a depth of about 140 ft. to shut off a water-bearing layer in the shale.

Jan 1, 1927

By William Kent

(Read at the Amenia Meeting, October, 1877.) IN a paper by Mr. Frank Firmstone, published in vol. iv, of the Transactions of the Institute, on "Comparison of Results from Open-topped and Closed-topped Furnaces," the regularity of the average grade of pig iron produced by the furnace under different conditions is expressed by means of a curve or diagram. The object of this note is to show that the graphic method, or that of representing variations by plotted curves or diagrams, is capable of a much more extended application to blast-furnace records, making a valuable auxiliary to the "furnace .book," and that by it the practical metallurgist may obtain at a glance information concerning the variations of the furnace during long periods, which could be found in the furnace book only after a tedious search. Plate XII is a graphic record of an anthracite blast furnace for one month. The table on page 554 gives the figures obtained from the furnace book, together with a record of temperature of the atmosphere, barometric pressure, and moisture in the air, which was obtained from a meteorological observatory not far from the furnace. In the records of a furnace, two of the variable qualities are final results, viz., the quantity of pig iron produced, and its grade; all the other variables are antecedent causes which produce the final results. Of these variable causes which contribute to the quantity of product and its grade, some are partially under the control of the furnace manager, others depend upon the state of the atmosphere, and still others are accidental. Of the first class are the character of the materials charged, and their relative proportions, their mechanical conditions, as wet or dry, large or small pieces, etc., the revolutions of the engine, the heat and pressure of blast, and the distribution of the charge. Of the second class are the number of pounds of air blown into the furnace for each stroke of the engine, the amount of moisture in the air, and the condition of the chimney draughts. These vary largely with the season of the year. Of the third. class is the leaking of a tuyere or a temporary stoppage. To keep a record of this kind for a whole year, it is only necessary to procure a sheet of common profile or cross section paper, about 38 inches long and 8 or 10 inches wide, with cross lines ruled about 0.1 of an inch apart. The vertical lines, or those in direction of the

Jan 1, 1878

By William Kent

In a paper by Mr. Frank Firmstone, published in vol. iv, of the Transactions of the Institute, on " Comparison of Results from Open-topped and Closed-topped Furnaces," the regularity of the average grade of pig iron procluced by the furnace under different conditions is expressed by means of a curve or diagram. The object of this note is to show that the graphic method, or that of representing variations by plotted curves or diagrams, is capable of a much more extended application to blast-furnace records, making a valuable auxiliary to the " furnace hook," and that by it the practical metallurgist may obtain at a glance information concerning the variations of the furnace during long periods, which could be found in the furnace book only after a tedious search. Plate XII is a graphic record of an anthracite blast furnace for one month. The table on page 554 gives the figures obtained from the furnace book, together with a record of temperature of the atmosphere, barometric pressure, and moisture in the air, which was obtained from a meteorological observatory not far from the furnace. In the records of a furnace, two of the variable qualities are final results, viz., the quantity of pig iron produced, and its grade; all the other variables are antecedent causes which produce the final results. Of these variable callses which contribute to the quantity of product and its grade, some are partially under the control of the furnace manager, others depend upon the state of the atmosphere, and still others are accidental. Of the first class are the character of the materials charged, and their relative proportions, their mechanical conditions, as wetor dry, large or small pieces, etc., the revolutions of the engine, the heat and pressure of blast, and the distribution of the charge. Of the second class are the number of pounds of air blown into the furnace for each stroke of the engine, the amount of moisture in the air, and the condition of the chimney draughts. These vary largely with the season of the year. Of the third class is the leaking of a tuyere or a temporary stoppage. To keep a record of this kind for a whole year, it is only necessary to procure a sheet of common profile or cross section paper, about 38 inches long and 8 or 10 inches wide, with cross lines ruled about 0.1 of an inch apart. The vertical lines, or those in direction of the

Jan 1, 1879

By William R. Barton

Iron and steel slag represent man's most successful attempt to date to profitably utilize a solid waste. Its consumption represents a solution to a solid waste problem and also represents tonnage of natural aggregates that will not have to be mined with concomitant disturbance of the land. Slag has been produced as long as iron has been made; but until a little more than 50 years ago, it was mostly a waste product to be disposed of with as little effort and cost as possible. Huge piles of waste slag were generated over the years of iron and steelmaking. Sporadic use was found for small amounts starting with slag (from Catalan forges) used for road bases by the Roman Empire. The first recorded sustained commercial use was, as is often the case in man's history, for making war. Some profit- conscious munitions maker in the 16th century realized that he could make cannon balls of slag instead of the more precious iron. Other small-volume uses gradually developed: cast building blocks, slag-lime mortars and cements, slag wool, ballast, road base, and, finally, in concrete. But it was not until after World War II that the true potential of blast-furnace slag as a construction aggregate was really recognized. Now nearly all blast-furnace slag produced is used, and much of the earlier stock- piles in the U. S. have been reduced or entirely consumed. Steel slag for aggregate use has been in commerce for only the past 10 years, and use has increased rapidly (10-50% per year) during the past 5 years as blast-furnace slag supplies became depleted. However, much remains to be accomplished in determining character and optimum conditions of use for various types of steel slags before such slags will realize their full use potential. Although slag represents only 2% of construction aggregate materials used in the U.S., its production involves certain features that make its production record far more important than national tonnage figures would indicate. Its source is in iron and steel production and concomitantly slag availability is restricted to those areas where iron or steel is produced. In such areas, it often represents one of the principal aggregates marketed and, because of special properties that make slag a selected aggregate for certain uses, the tonnage imbalance may be overcome by the importance of its contribution to quality or special characteristics of end products. The location and number (Fig. 1) of slag plants handling this annual production is governed by the geographic makeup of the iron producing industry. Prior to the period marked by World War 11, most blast furnaces were in the Great Lakes area-Pittsburgh, Cleveland, Chicago, Gary, Buffalo, Detroit, Youngstown, and Toledo, with exceptions at Baltimore, Bethlehem, and Birmingham. Since that time, iron and steel facilities have been established in Texas, Utah, and California. Today 85 slag plants in 15 states provide employment for almost 2000 persons. The slag plants also recover almost 4 million tons of slag-encrusted iron each year for return to the blast furnaces. Much of the success in developing uses for slag can be attributed to the efforts of the National Slag Association founded in 1918. Since then, it has conducted numerous field and laboratory investigations to demonstrate the properties and uses for slag and slag products. These investigations have resulted in total recognition of blast-furnace slag as a construction material of consequence. The American Society for Testing & Materials Designation C125 recognizes blast-furnace slag as "the nonmetallic product consisting essentially of silicates and aluminosilicates of

Jan 1, 1975

By C. Y. Clayton

In connection with certain cooperative work carried on between the Ordnance Department of the U. S. Army, the U. S. Bureau of Mines, and the U. S. Geological Survey during the year 1918, it was the writers' privilege to make metallographic examinations of a great many test bars and other pieces of nickel-steel gun forgings. The material studied came from many different steel plants throughout the country and consisted both of forgings that had been accepted by the Ordnance Department and those that had failed to pass the specified physical tests. In general, these tests require a minimum tensile strength of 95,000 lb. (42,091 kg.)! an elastic limit of 65,000 lb. (29,483 kg.), an 18 per cent, elongation, and a 30 per cent. reduction in area. An average chemical composition of the steel studied is 0.38 per cent. carbon and 2.9 per cent. nickel. The steel was of both basic electric and basic open-hearth manufacture. The object of the metallographic work was twofold: to assist in detecting defects in the steel and, if possible, to suggest remedies for the same; and to obtain as much information as possible in regard to the relation of the microstructure of the metal to its physical properties. The grcatcr part of the investigation was devoted to defective metal that failed to pass the ordnance specifications. Many types and kinds of more or less serious defects thus came under observation, but most of these were due to the attempts by the manufacturer to meet the enormous demand for ordnance steel with more or less inadequate equipment, and were soon remedied. Two defects, the so-called "flakes" or "snowflakes" and a certain "fibrous" or "woody" fracture, were encountered so frequently and were so disastrous to the steel that the greater part of the study was devoted to them. As a result much information as to their nature and their effects upon the steel and something in regard to some of the conditions that favor their development has been obtained. The purpose of the present

Jan 1, 1920

By J. F. Myers, R. J. Tower

"THERE is nothing new under the sun." All over the world, mineral-dressing engineers are working at their problems, no two of which are alike. Each encounters equipment and process problems. Many devise simple ways and means of overcoming their difficulties. Many of these problems are quite common in the industry, yet, since no one human being seems capable of thinking of everything, these problems at some plants often are looked upon as necessary evils. The purpose of this symposium is to gather together, from competent engineers, devices and practices that have been useful to them. Most of the ideas contributed are not new, yet there is no plant operator, old timer or youngster, who will not find some idea herein that will give him a suggestion for improving his operation. Space does not permit a complete elaboration on all of the contributions offered. Each item is summarized, but this will be ample for those skilled in the art of mineral dressing. A list of contributors appears at the end of the paper, and the superior number at the end of each item identifies its source. GENERAL EQUIPMENT A signal light to show that a steel bin, containing relatively fine, moist ore, is full, can be made by suspending a copper rod in the bin to a sufficient depth to ensure ample contact with the ore. One wire of a 32-volt circuit should be attached to the rod and one to the side of the bin. Sufficient current will flow to make the signal light burn. A 110-volt circuit could be used, but 32 volts ensures safety.10 Fig I shows a circular bin for crushed ore. It is a concrete structure footed on the ground, using no supporting columns. Tailing from the sink-float was used for aggregate. Cross conveyors for discharging ore are not required, nor is a tripper for filling. Segregation is minimized by drawing from different gates. An exhaust fan on top of the bin eliminates condensation due to temperature of the ore.21 A beam with an adjustable point of suspension near the center permits rigging rolls for removal in a very few minutes. This makes unnecessary the lacing of the cable through the hub bolts on one side, around the shaft on the other, and the trouble of balancing the load.8 The ratchet handle on a Symons crusher may be replaced by a drum with a cable wound on it. When the cable is pulled by a crane or hoist it causes the drum to revolve and thus screws or unscrews the bowl. This reduces handwork and materially shortens the time required for the job.3 To spread ore feed from an apron feeder over a belt conveyor, place a heavy steel bar about midway between the top

Jan 1, 1947

By H. J. Denning, M. W. Brabbins, A. K. Isaac

The quality of a coalface floor is the essential element that enables powered supports to generate their designed loads in control of coalface strata. The paper introduces a technique for the appraisal of coalface foundation stability. A criterion of support efficiency, viz., the support pressure increase/strata convergence, is included in case study data obtained from investigations in the South Wales Coalfield, U.K.

Jan 1, 1984

By Samuel H. Dolbear

THE purpose of a technical report is to record facts, usually collected by investigation, and to interpret these facts in understandable language. The audience may range from a small shareholder without technical knowledge, to a highly trained engineer or geologist. If the client is a mining company with technically trained executives, the report writer's problem is relatively simple. The writer will then be appraised not only for his conclusions, but for clarity of language and organization of the report. If the writing is bad, the construction careless, and there is a failure to clearly convey to the reader the facts and the author's conclusions, the report is a failure and the writer may have damaged his professional character. Spoken words die quickly, written words may constitute a permanent record and if they are badly composed they may rise up to damn the author. "A good measure of an author's understanding of his subject is his ability to express it clearly in plain words." Good English Teachers in the fields of mineral technology have frequently complained that even in post-graduate groups there is an appalling indifference to their appeals for good English. Some have even noted a student's belief that the use of refined English is effeminate. If those with such immature beliefs could measure the pay-check damage arising from the use of "sloppy" language, they would realize that precision and refinement in English may be quite as important as technical accuracy. When the reader audience is without technical knowledge simplicity in treatment becomes especially important. If one is engaged in consulting work, in government service, or in any field where reports have public distribution, the language employed should be technically adequate but simple enough to be understood by non-technical readers. For example, one may use the term "visual" in place of "megascopic." Technical language can be so obscure that it cannot be understood even by highly-trained students. In the March-April (Vol. 47-No. 2) issue of Economic Geology, Nicholas Vanserg ridicules these extremes and quotes various paragraphs from published material, such for example: "However, lattice orientation unaccompanied by cognate dimensional orientation can never be attributable to growth from an isotropic blastetrix." "The temperature declines because of cessation of the exothermic chemical and mechanical equilibriopetal processes." These he calls "good geologese" and they are calculated not only to baffle the reader but to impress upon him the erudite character of the author. Revision In some cases, difficulty arises from the fact that the writer is too close to the subject and unconsciously assumes that his reader is equally familiar with the background of the report. It is difficult for the writer to regard his work objectively and to determine to what extent it is likely to be understood. Every important manuscript will gain in clarity if the author will have it reviewed by an informed reader. But the writer must not be oversensitive to criticism and should not treat his composition as perfect and beyond the possibility of improvement. The first draft of a report always requires revision, regardless of the care used or the ability of the writer. Three or four revisions are not uncommon. The first draft usually requires expansion in places, the deletion of non-essential material, and language changes to promote clarity of expression. This should be done by the author after a lapse of time, even if only overnight, in which his mind has been occupied on some other subject. Possible improvements are always more visible. The manuscript should be passed on to another reader for further suggestions. Organization of Material The engineer should study available reports and library references before going into the field. If the previous reports have been responsibly done and can be accepted as correct, then much field time can be saved. It is, of course, customary to make some on-the-ground checks to confirm earlier reports, particularly those relating to ore reserve which may have undergone changes. Report writing requires time and expense, but nevertheless, the basic reasons for conclusions should be presented even in the case of a worthless property, for it may prevent a duplication of the work. If the mine examined is obviously of no further interest, no useful purpose can be, served by preparing a report in detail. In one case an engineer travelled all the way to South America only to find that the mine had been grossly misrepresented and was valueless. His cabled report "Nonsense" is a case of over-simplification, but it served his company's purpose. The first step in report organization should be the selection of subjects. This should be done at the mine, and the data collected for each subject should be reviewed in considerable detail on the ground. Otherwise one may find that he has failed to collect some essential details not readily obtained after he has returned to headquarters. If the property to be described is undeveloped, then many of the subject titles are automatically eliminated. Usually no useful purpose is served by an attempt to calculate the cost of production under such circumstances, although the cost of exploration

Jan 1, 1952

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 *ABBOTT, CHARLES W., Min. Engr. Pioche, Nev. ?08 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94 *AOTT, ROBERT R., Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 || ARAHAMS, ALEXANDER I., Student.. .67 E. 93rd St., New York, N. Y. '13

Jan 1, 1917

By J. H. Scaff, W. G. Pfann

The effects of impurities on the electrical properties of silicon are discussed in a companion paper by Messrs. Scaff, Theuerer, and Schumacher.' It was shown that an ingot of silicon which contained boron and phosphorus in certain concentrations consisted partly of p-silicon and partly of n-silicon2 and that the common boundary between these regions was the source of a photo-voltage. These features were ascribed to the segregation of boron and phosphorus during solidification of the ingot. Because of different rates of segregation the first portion of the ingot to freeze contained a molar excess of boron over phosphorus and hence was p-silicon. The last-solidified region contained a molar excess of phosphorus and was n-silicon. This paper is concerned with the microscopic examination of such ingots. The microstructures are rather unusual in certain respects and their study has helped to show how the segregation of minor elements modifies the electrical properties of silicon. The microstructures of ingots prepared from two lots of silicon, designated 1 and 2, will be described. These lots were obtained from the Electro Metallurgical Co. Both contain 99.8+ pct silicon, but they differ in impurity analysis. For each lot will be shown the microstruc-ture of a slowly cooled ingot, for which the time of solidification is 6 min., and that of a rapidly cooled ingot, for which the time of solidification is 2 min. The ingots were prepared from 45 g charges of silicon. When an alloy freezes a cored structure is generally produced because of insufficient diffusion to remove concentration differences established during freezing. As a result of coring the first portion of a crystal to freeze is usually poorer in solute than equilibrium requires, while the last material to solidify is richer. In a columnar grain, growth is principally unidirectional and coring can produce a concentration gradient along the entire grain. By carrying the picture of the coring process from a single grain to an entire ingot in which columnar grains are aligned more or less radially, one can easily see that a composition gradient could be established between the outside and center of the ingot. This, to a considerable extent, occurs during the solidification of a slowly cooled ingot of silicon. Slowly Cooled Ingot In slowly cooled ingots of both lots of silicon, columnar grains which are approximately radial in direction and longest at the top of the ingot enclose a region in which the shapes and align- ment of the grains are considerably less regular. The central region is last to solidify and contains cavities and inclusions. The sketch of Fig 1 illustrates some of these features, as well as others which will be described below. If a polished section of an ingot is etched in a mixture of 2 parts of 20 pct HF and 98 parts of HNO3 the p-n barrier becomes visible. The overall shape of the barrier in a slowly-cooled ingot is roughly oval, as may be seen in Fig 1. The proportion of n-silicon, that is, the region enclosed by the barrier, is considerably greater in ingots of lot 1 than in those of lot 2. A sample about 34 x 1/8 X 1/8 in. was cut from a slowly cooled ingot of lot 1 with its long direction extending from the top of the ingot to the porous region. Thus its upper half was psilicon, its lower half n-silicon. A longitudinal face was polished and etched in the acid mixture. The areas of interest are identified in Fig 2. A band of parallel markings extends across the sample in the columnar region. These striae are roughly parallel to the upper surface of the ingot and cross grain boundaries with only slight deviations. They are quite distinct in the n-silicon,

Jan 1, 1950

By J. W. Goss, M. J. Coolbaugh

A survey of literature published in the U.S. on grouting indicates that most such work has been done to stop water flow in mines and for stabilizing foundations of various man-made structures. Apparently San Manuel is one of the first mines in this country to use grout extensively underground for the strengthening and stabilizing of ground about drifts, shafts, and stations.

Jan 3, 1961

On July 25, the first copper ore From American Smelting & Refining Co.'s Mission open pit nine was sent into the new 15,000-tpd concentrator : three clays later, the first rail cars containing the Mission concentrate were sent north to the smelter at Hayden, Ariz. Thus two y,ears after stripping was started, Asarco's new mine, located south of Tucson. went on stream several months ahead of schedule. The plant, designed and constructed by Western Knapp Engineering Co., is expected to be operating at full capacity about September 1. with present plans calling for the copper concentrate from Mission to be shipped to Asarco's smelters at Hayden and El Paso.

Jan 9, 1961

By H. Conrad, V. V. Damiano, G. J. London

A method is described for producing single crystals of high-purity beryllium, Be-4.37pct Cu, and Be-5.24 pct Ni. These crystals were prepared for testing in compression parallel to the [0001] by orienting and lapping to within ±3' of arc of the (0001). Microstrain testing apparatus is described along with c axis compression results for ingot purity beryllium, twelve-zone-pass material, and the above-mentioned alloys. Results show no measurable plasticity for the ingot purity material from -196" to 400°C, although some surface traces of (1122) slip was observed at 200°C and above. The twelve-zone-pass material shows substantial microstrain plasticity at 220°C with slip on (1122). Both alloys show significant plasticity at room temperature and above with slip also on (1122) planes. THE two slip systems which normally operate during the plastic deformation of beryllium in the vicinity of room temperature are:' basal slip (0001)(1120) and prism slip . Pyramidal slip with a vector inclined to the basal plane has been reported for elevated temperatures,'-a but occurs near room temperature only at very high stresses.~ A summary of the available data on the effect of temperature on the critical resolved shear stress for slip on these systems has been compiled by Conrad and Perlmutter.~ It has been postulated6'7 that one of the principal factors contributing to the brittleness of poly crystalline beryllium at temperatures below about 200°C is the difficulty of operating pyramidal slip with a vector inclined to the basal plane. Hence, detailed information on the operation of such a slip system is important to understanding the brittleness of beryllium. The operation of pyramidal slip with a vector inclined to the basal plane is best accomplished in beryllium by compressing single crystals in a direction parallel to the c axis. In such a test the resolved macroscopic shear strzss on the basal and prism planes is zero and (1012) twinning which is favored by tension along the c axis does not occur. Hence, in c axis compression of beryllium the normal deformation modes are inhibited and the operation of pyramidal slip with a vector inclined to the basal plane is favored. In the present investigation, c axis compression tests were performed on beryllium single crystal as a function of temperature (77" to 700°K), purity (commercial and twelve zone pass), and alloy content (4.37 wt pct Cu and 5.24 wt pct Ni). Presented here is a description of the test techniques employed and the gross mechanical behavior observed. A detailed analysis of the slip traces developed on the surfaces of the deformed specimens during these tests and the results of electron transmission studies of the deformed crystals are given in a separate paper.B PROCEDURE 1) Materials and Preparation. Single crystals about 1 in. diam were prepared of the following materials: commercial-purity beryllium, high-purity beryllium, and two beryllium alloys, one with 4.37 wt pct Cu and the other with 5.24 wt pct Ni. The commercial-purity single crystals were obtained by cutting specimens from large-grained ingot of Pechiney SR material, which is approximately 99.98 pct pure. The high-purity crystals were prepared by floating-zone refining (twelve passes) a rod (7 in. by 1 in, diam) of Pechiney SR grade cast and extruded beryllium. Although an absolute chemical analysis of the zone-refined material was not established, mass spectro-graphic analysis, emission spectrographic analysis, and y activation analysis indicated that it contained in atomic fractions about 5 to 10 ppm each of carbon and oxygen, 1 to 5 ppm each of nickel and iron, and about 1 to 2 ppm of copper, with the remaining residual impurities being less than 1 ppm. Further indication of the purity of this material is provided by the critical resolved shear stress for basal slip, which was approximately 300 psi. The starting material for the alloy single crystals was 1-in.-diam floating-zone-refined (six passes) rod of Pechiney SR grade beryllium. Two such rods were wrapped respectively with sufficient weight of wire of high-purity copper (99.999 pct) or nickel (99.999 pct) to yield a 5 wt pct alloy. A seventh floating-zone pass was then applied to each of the rods to accomplish the initial alloying and an eighth pass for homogenization. Analytical samples were taken from regions of the rod immediately adjacent to where the mechanical test specimens were cut; these indicated 4.37 wt pct Cu and 5.24 wt pct Ni. 2) Crystal Orientation. To avoid the occurrence of basal slip during c axis compression testing, it is necessary to load the crystals as nearly parallel to the c axis as possible. Preliminary c axis compression tests indicated that plastic flow and/or fracture occurred at stresses of the order of 300,000 psi; hence on the basis of a critical resolved shear stress for basal slip of 300 to 400 psi, the maximum crystal misorientation permitted is about 4 to 5' of arc. Since this accuracy cannot be obtained using the usual back-

Jan 1, 1969