Search Documents

By D. F. Kaufman, E. D. Levine, L. R. Aronin

ThE primary slip plane in hcp metal crystals can usually be inferred from the c/a ratio. Basal slip is the primary system at room temperature for zinc, cadmium, magnesium, cobalt, and rhenium, all of which have a c/a ratio greater than 1.60. Zirconium and titanium, on the other hand, each with a c/a ratio of 1.59, deform primarily by (1010) [ll20] prismatic slip. The increasing tendency toward prismatic slip in these materials is generally thought to be associated with the increase in atomic density on (10i0) as c/a is reduced. Beryllium, with a c/a ratio of 1.57, would, according to the above scheme, be expected to exhibit prismatic slip. However, in beryllium of commercial purity, the primary deformation mode at room temperature is basal slip.' The ratio of critical shear stress for prismatic to that for basal slip at room temperature is approximately 5:l. The critical shear stress for prismatic slip decreases quite rapidly with increasing temperature, however, and at 500°C the ratio is approximately unity. The apparently anomalous behavior of beryllium has led to speculation that prismatic slip in this material may be restricted by an anisotropic effect of impurities,' and that, if beryllium could be purified to a sufficient extent, prismatic slip might predominate at room temperature. In such a case, the conditions under which basal cleavage can occur would be suppressed, and enhanced low-temperature ductility might result. With the advent of the floating-zone method for purification of beryllium,3 it has become possible to determine experimentally the effects of purification on basal and prismatic slip. Tensile tests were performed at room temperature on single crystals oriented favorably either for basal or prismatic slip. The crystals had been purified to various extents by zone-refining, employing procedures that have been described elsewhere.4 Relative purities of the crystals were estimated by measuring the ratio of electrical resistance at 4.2"K to that at 298°K. Typical values ranged from 0.40 for commercial-purity material to 7.7 X 10"4 for crystals prepared from vacuum-distilled beryllium and subjected to six zone-refining passes. The purity dependence of the critical shear stresses for basal and prismatic slip is shown in Fig. 1. In the purity range studied, the critical shear stress for basal slip is decreased from 1.4 to 0.14 kg per sq mm. The critical shear stress for prismatic slip is decreased from 6.7 to 5.3 kg per sq mm. The decreases in critical shear stress for each deformation mode, therefore, are approximately equivalent. No purification anisotropy is observed. Because of the absolute magnitudes of the critical stresses, the ratio of the critical shear stress for prismatic slip to that for basal slip actually increases from 5:l to 38:l at the highest purity level studied. It is evident, therefore, that basal slip is the primary deformation mode in high-purity beryllium. This fact must be accounted for in any rationalization of the deformation behavior of hcp metals. This work was performed at Nuclear Metals, Inc., under the sponsorship of the U.S. Atomic Energy Commission.

Jan 1, 1964

By Walter J. Karplus, Otto J. M. Smith

The transient response of earth formations may be tlcter.171ined by means of four electrodes mounted coli-rienrly on n sonde. Exponentially decaying current pules are applied to one pair of electrodes and the re.rrrlting voltage transient at the other pair is recorded. It is shown by theoreticol analysis and verified by laboratory experiments that this arrangement readily yields the direct resistivity of the formation and provides valrrable additional information as well. INTRODUCTION Although electrical transients have been employed with moderate success in geophysical prospecting, their application to well logging has received virtually no attention in technical literature. In the conventional direct resistivity logging methods only the zero frequency impedance of the formation under study is measured, and no information is obtained regarding its reactive characteristics. Since the use of certain transients appears to offer some advantages in this respect, experiments were performed on a laboratory scale to investigate this possibility. This investigation was limited to a study of a four-electrode array where both the receiving and transmitting electrode pairs are mounted on a logging sonde, and decaying exponential pulses are applied to the transmitting electrodes. THEORY Given an electrode configuration as shown in Fig. I, located in a homogenous medium of resistivity p, if each electrode has an effective radius, r, which is small compared to the spacing, s and a, it is easy to show by integrating the volume resistivity that the input resistance, Rrw, of the transmitting electrodes is Rxw=p/2pr If a capacitor of capacity C, charged to a voltage Em, is suddenly connected to these electrodes, the resulting current, I(t), will then be The voltage transient, E(t), at the receiving electrodes may then be found by substracting the resulting potential at electrode Y from that appearing at electrode Z. and by inserting Eqs. 1 and 2 Integrating Eq. 4 with respect to tim

Jan 1, 1957

By Neil O. Johnson

In the cyanidation of gold, silver and mixed ores, the solids, suspended in the pulp after fine grinding, primary settling and scries agitation arc subjected to a washing step known, generally, as countercurrent decanta-tion, abbreviated C.C.D The conventional C.C.D. plant consists of a series of separate thickeners—three to five in number—arranged in series on slightly different elevations. Solids settled in the first thickener are pumped at maximum density into the second thickener, where they arc diluted with weak solution overflowing the third. After settling in the second thickener they are pumped to the third, where the process of repulping with still weaker solution is repeated, and so on throughout the system, until they reach the last thickener and are repulped with barren solution or water. Recently there has been developed a new type of thickener, known as the Dorr Washing Tray Thickener, consisting of up to five individual thickeners, which performs in a single unit all the functions of a conven-tional C.C.D plant. Fig. 1 illustrates the essential features. It is a multicompartment tray thickener, in which the trays operate in scries instead of in parallel for countercurrent washing. Feed enters the top compartment via a central, semisubmerged feed well. Strong solution overflows into a peripheral launder. Solids settle to the bottom, are raked to the center and flow into the top of the second compartment, directly below, via an inverted cup and scal. Solids pass downward, compartment by compartment, against a counter flow of wash solution and finally of fresh water. Thus, in accord-:trice with the basic C.C.D. principle, the solids transfer the dissolved metal content to the wash solution and finally are removed by a diaphragm pump from the bottom compartment virtually free of valuable material. Similarly, the wash water, as it flows through the system, becomes increasingly enriched in dissolved metal until it overflows from compartment two and returns to the process.

Jan 1, 1939

By Neil O. Johnson

In the cyanidation of gold, silver and mixed ores, the solids, suspended in the pulp after fine grinding, primary settling and scries agitation arc subjected to a washing step known, generally, as countercurrent decanta-tion, abbreviated C.C.D The conventional C.C.D. plant consists of a series of separate thickeners—three to five in number—arranged in series on slightly different elevations. Solids settled in the first thickener are pumped at maximum density into the second thickener, where they arc diluted with weak solution overflowing the third. After settling in the second thickener they are pumped to the third, where the process of repulping with still weaker solution is repeated, and so on throughout the system, until they reach the last thickener and are repulped with barren solution or water. Recently there has been developed a new type of thickener, known as the Dorr Washing Tray Thickener, consisting of up to five individual thickeners, which performs in a single unit all the functions of a conven-tional C.C.D plant. Fig. 1 illustrates the essential features. It is a multicompartment tray thickener, in which the trays operate in scries instead of in parallel for countercurrent washing. Feed enters the top compartment via a central, semisubmerged feed well. Strong solution overflows into a peripheral launder. Solids settle to the bottom, are raked to the center and flow into the top of the second compartment, directly below, via an inverted cup and scal. Solids pass downward, compartment by compartment, against a counter flow of wash solution and finally of fresh water. Thus, in accord-:trice with the basic C.C.D. principle, the solids transfer the dissolved metal content to the wash solution and finally are removed by a diaphragm pump from the bottom compartment virtually free of valuable material. Similarly, the wash water, as it flows through the system, becomes increasingly enriched in dissolved metal until it overflows from compartment two and returns to the process.

Jan 1, 1939

By J. A. Retty

IN the Labrador iron fields two concessions, totaling nearly 24,000 square miles, have been staked out and commercial-grade deposits delineated. The Newfoundland-Labrador concession, owned by the Labrador Mining and Exploration Co. Ltd., is a 20,000-square-mile tract in the upper basins of the Hamilton and N askaupi Rivers which drain into Lake Melville. The New Quebec licensed area is 3900 square miles, owned by the Hollinger North Shore Exploration Co. Ltd., lying to the northwest of the northwestern part of the Labrador concession. It includes the upper basin of the Swampy Bay River and part of the upper basin of the Whale River, both of which drain into Ungava Bay. Both of the above-named companies are controlled by Hollinger Consolidated Gold Mines Ltd. with The M. A. Hanna Co., of Cleveland, holding a minority interest. When exploration was first undertaken in 1936, the only published map of the area was that prepared by A. P. Low in 1895. It showed only the main watercourses and gave only a rough, general idea of the geology. The numerous lakes of this vast area had to be first sketched and then mapped. Since then, extensive geological and topographical surveys have been conducted by the Labrador company, work which is normally done by Government branches. The object of the work was to examine the area and gradually eliminate unfavorable or less favorable prospecting ground. With this object in view, geological

Jan 1, 1948

By C. P. Walker

Determining the distance to remote objects by observing the time required for sound to traverse the intervening space is an old practice. Attempts have been made to use this method for determining the fluid level in oil wells but as far as the writer is aware it was not found to be practicable, because vibrations in gas in the audible frequency range do not travel as well and as far as low-frequency pressure waves, which are capable of transmitting a greater amount of energy than can be transmitted by audible waves. Wood, in his book "Sound," states that in a given medium the range of sound transmission will vary inversely as the square of the frequency. The fact that the sound from a whistle having a low tone has a much lower attenuation rate than that from a whistle of high pitch is well known. Also, the pressure waves caused by cannon fire often rattle windows at points so distant that no sound of the cannon is heard. In 1932 P. E. Lehr and H. T. Wyatt, of the Shell Oil Co., experimented with the principle of the concussion, or pressure-wave echo, method of determining fluid levels in oil wells. They released compressed gas into the top of the casing, thereby creating a pressure wave, which traveled down the well and back again. Their experiments proved conclusively that, with the proper apparatus for recording the echoes and determining the velocities at which the waves travel, the method could be used successfully for determining fluid levels in oil wells. Wells are often equipped with from one to three tubing catchers and these together with the top of the liner are frequently above the fluid. Each of these obstructions reflects a part of the pressure wave. In such wells there may be, therefore, as many as five pressure-wave reflections. Thus it is obvious that in order to identify the various reflections and to determine therefrom the fluid level in a well it is necessary to obtain a graphic record of these reflections.

Jan 1, 1937

By Neil Johnson

IN the cyanidation of gold, silver and mixed ores, the solids suspended in the pulp after fine grinding, primary settling and series agitation are subjected to a washing step known, generally, as countercurrent decanta-tion, abbreviated C.C.D. The conventional C.C.D. plant consists of a series of separate thickeners-three to five in number-arranged in series on slightly different elevations. Solids settled in the first thickener are pumped at maximum density into the second thickener, where they are diluted with weak solution overflowing the third. After settling in the second thickener they are pumped to the third, where the process of repulping with still weaker solution is repeated, and so on throughout the system, until they reach the last thickener and are repulped with barren solution or water. Recently there has been developed a new type of thickener, known as the Dorr Washing Tray Thickener, consisting of up to five individual thickeners, which performs in a single unit all the functions of a conven-tional C.C.D. plant. Fig. 1 illustrates the essential features. It is a multicompartment tray thickener, in which the trays operate in series instead of in parallel for countercurrent washing. Feed enters the top compartment via a central, semisubmerged feed well. Strong solution overflows into a peripheral launder. Solids settle to the bottom, are raked to the center and flow into the top of the second compartment, directly below, via an inverted cup and seal. Solids pass downward, compartment by compartment, against a counter flow of wash solution and finally of fresh water. Thus, in accord-ance with the basic C.C.D. principle, the solids transfer the dissolved metal content to the wash solution and finally are removed by a dia-phragm pump from the bottom compartment virtually free of valuable material. Similarly, the wash water, as it flows through the system, becomes increasingly enriched in dissolved metal until it overflows from compartment two and returns to the process.

Jan 1, 1939

[†Aaronson, Alfred E., Oil Producer, Pres., Tuloma Oil Cc Tulsa, Okla. '18 ¦Abad, Leopoldo F., College of Min., Univ. of California Berkeley, Cal. '23 ¦Abadilla, Quirico A., Geol. Dept., Cia. Mexicans de Petroleo "EI Aguila," S. A., Edifico "El Aguila," Esq., Calles Aurora y Comercio, Tampico, Tamps., Mexico. '20 ¦Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, 0. '21 Abbott, Clarence E., Gen'l Supt., Iron Mines Div., Tenn. Coal, Iron & R. R. Co., 1405 Minnesota Ave., Bessemer, Ala. '04] [ ]

Jan 1, 1925

By J. J. Egan, A. B. Kinzel

Much work has been done recently in an attempt to analyze the physicochemical mechanism involved in the production of steel by the open-hearth process. This has resulted in reducing the process to a series of interrelated phenomena obeying the usual laws of mass action and diffusion. Of these, the reaction of the iron oxide and carbon in the molten steel is of most interest from a technical point of view as it constitutes the main action in the usual steelmaking processes. A. L. Feild' has formulated a basic differential equation expressing the open-hearth reactions and Herty has done considerable experimental work on the determination of a number of constants involved in the basic open-hearth reaction. In considering the application of the law of mass action to the reaction FeO + C + CO + Fe, the iron will be taken as constant, as is the case in the open hearth and the carbon monoxide pressure will be assumed constant at one atmosphere. From this xy = m at equilibrium, where x is the percentage weight of carbon, y percentage weight of iron oxide and m the weight-concentration equilibrium constant. While it is customary for physical chemists to express equilibrium constants in terms of molar concentrations, the constant is here expressed as the product of the percentage-weight concentrations for ease of comparison with the constants quoted by Herty and by Beild, and for more ready applicability to the open-hearth reactions. Herty and his associates have attempted to calculate the value of this constant from data on open-hearth heats. So many variables affect these results that an adequate calculation presents very great difficulties. A value of 4 X lop2 was first arrived at, but this was later changed to 1.6 X 10-2. Feild, in order-to illustrate the operation of the differential equation of the open hearth, has assumed a value considerably lower than Herty's, namely, 1.0 X 10-2, the largest value consistent with certain theoretical

Jan 1, 1929

By Richard Moldenke

The paper describes the making of pig iron from the Mayari iron ores of Cuba. The outstanding feature f this pig iron is a considerable content f nickel and chromium. As a marked improvement in the quality of castings has been noted when this iron is used in the foundry mixtures, a series f melting tests f mixtures of great variety of composition was conducted with the idea f getting comparative strengths from which the effect of nickel¬chromium could be seen. These tests, on account of their number, and degree of accuracy desired, were made by the crucible melting method. The paper gives the tables of results, a series f curves showing the inter-relation of the elements involved, and a summary of the conclusions derived. THE presence of nickel-chromium in pig iron made from Cuban ores is so well known that the word "Mayan" is unconsciously associated with it. Since 1904, when exploration of the Mayari deposits of iron ore in northeastern Cuba was undertaken, there has been increasing interest in these ores. The TRANSACTIONS contain numerous references to them. This iron ore, which is shipped to the. United States in the nodulized state, has been thoroughly tested and found very valuable; the deposit covers over 25,000 acres and there is in sight over 500,000,000 tons of ore that, by systematic mining, runs practically constant in composition. With nickel and chromium present, also titanium in sufficient quantities to attract attention, as well as extremely low phosphorus and sulfur contents, the iron founder is naturally interested in the utilization of Mayari ore for pig iron for the better grades of finished iron products. The present point of consumption of Mayari ore is at Sparrow's Point, where Mayari pig iron of any desired composition is made. The com-

Jan 9, 1922

Lewis, B. LINDEMUTH, ?New York, N. Y.-I would like to confirm Dr. Howe's supposition that a process could be worked out for steel along similar lines. About 1 ½ years ago, F. D. Carney and myself were working on the elimination of columnar crystals which are particularly evident in nickel steel. We discussed rotation and varying speeds of rotation, but figured that with just rotation the steel would eventually catch-up to the motion of the mold and that the desired effect could not be obtained in that way, so we decided to alternate the direction of rotation. We rigged up in ordinary commercial turntable and on the same mounting attached a blast, furnace and mud gun, which is a simple steam cylinder, and mounted an 18-in. ingot mold on the turntable. The turntable had a stroke of about 10° to 12°, with stops at the ends. The steam cylinder would bang the table against the stops so that the stopping was so violent that it would tend to keep the metal in motion when the mold stopped and thus wash away any crystals that would form. We made quite a few interesting experiments; the results of which were that the columnar crystallization was entirely eliminated. At the same time we cast ingots in a similar mold, allowing the molds to remain stationary; these showed columnar crystals of from 2 to 4 in. in depth. The grain structure of the balance of the ingots, which were rotated, was very much finer than the grain structure of the ingots that were cast and allowed to cool slowly. The experiments were made on a 0.35 per cent. carbon nickel steel, which is probably more susceptible to columnar crystallization than any other. I think that the rolling properties and the forging properties of some alloy steels could be very much improved by a similar method, or some commercial method of casting ingots to eliminate this columnar crystallization.

Jan 5, 1919

By Frank Wartman

RECENTLY Horace Freeman1 obtained a patent on a successful method of conducting a roasting procedure described as to general features by Carl Schnabel2 almost forty years ago. Essentially, the Freeman process of roasting consists in introducing the finely powdered sulfide mineral, suspended in air or any other suitable gaseous medium, into the upper portion of a heated chamber. The stream of suspended particles is directed vertically downward. A counter-current stream of gas introduced at the bottom of the chamber flows upward. The mineral particles are oxidized as they fall through the heated atmosphere of the chamber. All air required for the oxidation may be admitted either at the top or the bottom of the chamber, or may be divided between the top and bottom inlets in any desired proportion. Heat may be recovered by passing the gases leaving the furnace through a waste-heat boiler or other form of interchanger. In speaking of the results obtained in roasting pyrite, Freeman says:3 Steam yield from the boiler exceeds 1 pound of steam per pound of pyrite con-sumed, which pays the cost of operation of the burner. The oxide produced is in the form of fused particles or hollow shells of magnetite, containing about 65 per cent of iron. It contains the gangue material ordinarily produced in flotation concentrate, of course, but it is being found that most of this can be eliminated by magnetic separa-tion, and that the sulfur content, as consistently produced, is below 0.2 percent. This material is especially interesting as a high-grade iron ore, free from phosphorus and low in sulfur. It may be sintered or briquetted. It is even more interesting as a raw material for sponge-iron production, to be directly smelted in electric furnaces without the usual cooling of the iron powder and magnetic separation between the reducing kiln and the electric furnace.

Jan 1, 1933

By J. E. Johnson

OF the many items of information necessary to the successful management of the blast-furnace, few are more important than knowledge of the location and movement of the stock-line: whether the furnace is full and has. been kept so; whether the stock is settling regularly or slipping; and, if slipping, how often it has slipped, at what times, and how far at each time. To obtain these data, a man is sometimes stationed at the top of a. pair of mechanically-filled furnaces, simply to watch and gauge them by hand in the old-fashioned way. - A more recent practice is the suspension of test-rods from ropes leading over pulleys to the ground-level, where the ropes are wound on small drums with graduated peripheries and provided with crank-handles, whereby the skip-man or some other person can quickly and conveniently gauge the position of the stock-line in the furnace. I believe the credit for this great improvement belongs to Messrs. McClure & Phillips of Sharon, Pa., who were, as far as I know, the first to apply it, and who have a patent for it. The valuable indications gained by application of the Uehling pyrometer to the down-comer are Dot to be ignored; but the information thus furnished is somewhat indi¬rect, and there is no scale for the translation of "top-tempera¬tures " into " feet down." Moreover, this apparatus as a whole is delicate, and the cost of its installation and maintenance is high. If the record furnished by the Uehling pyrometer is not in the most desirable form, the test-rods, on the other hand, give no record at all, except through the memory, or notes of a man who, to say the least, is not gauging continuously, and who may omit to report an improperly low stock-line, if it be due to a fault of his own.

Mar 1, 1905

By J. E. Burke, C. W. Mason

IN attempting to study precipitation from a tetragonal lattice using solid solutions of bismuth in tin, it was found that although a Widnmanstatten pattern is observed 1 only a qualitative analysis of the orientation relationships is possible, because of the unusual structural changes that accompany the precipitation process MICROSCOPICAL STUDIES Alloys were made from Chempur tin (Standard samples 42b and 42c, National Bureau of Standards), and bismuth (Kahlbaum C P ) by melting neighed quantities together under palm oil, stirring well, and casting in a heated graphite mold The polishing and etching techniques employed largely govern the visibility of the structural changes The preliminary surfacing operations were similar to those recommended by Villela and Bergekoff,5 through BehrManning 3/o abrasive papers, lubricated by a solution of paraffin in kerosene A rough metallographic polish was next given, using a thin cotton cloth charged with relevigated alumina (maximum particle size of about 4µ) and soap solution, repeated etching and polishing served to remove disturbed metal For high-power examination better preparation was necessary It was found that on such soft metals the threads of the fabric, rather than the abrasive, cause most of the scratching Cotton outing flannel, which had been brushed so that the nap lay down, was fairly satisfactory, but a Heavy grade of silk velvet (not the noncrushable kind) was found to be better, especially after some use A better procedure was as follows The metal lap was warmed slightly, and a 4-in circle of woolen broadcloth was cemented to its center by a thin film of melted paraffin The broadcloth was then moistened with water, and a 30 to 40 per cent solution of sodium hydroxide heated to about 50°C was poured over it, allowed to stand for 1 to 2 min and then washed off It was neither necessary nor desirable to remove all the sodium hydroxide from the cloth, since its etching action aided in the removal of the flowed layer from the sample The cloth was then charged with a paste of the relevigated alumina in water Since this lap did not remove deep scratches, it was necessary previously to polish the specimen on some material such as the silk velvet The sodium hydroxide softens and partly gelatinizes the woolen lap covering, permitting a scratch-free polish, but its action continues, and the cloth deteriorates after about 24 hr This is not serious, because a new lap can be prepared in about 5 min, and only small pieces of cloth are used Etching with a strongly acid solution of ferric chloride was found satisfactory for removing the flowed layer For the final etching, the most satisfactory reagent was that of Taffs,7 the formula for which is FeC13 6H20, 2 grams, HC1, 5 c c , H2O, 30 c c , C2H5OH (95 per cent), 60 c c This etchant reveals differences in com-

Jan 1, 1941

By John V. Beall

Copper production in the. United States in 1972 amounted to 1,658,000 tons according to the USBM. This figure is up over 1971 but falls below 1970 production of 1,719,101 tons. This report is essentially about the status of copper mining operations in the U.S. and is an update and expansion of the report "Southwest Copper-A Position Survey" published in [A=], October 1965. At that time, the trend was toward using larger equipment to mine lower grade ore and toward the expansion of dump leaching practice. That trend continues today but, it is overlain by intensive activity to comply with existing environ¬mental legislation and uncertainty over proposed revisions of venerable laws governing mining. In the U.S. today there is, practically speaking, no excess smelting capacity so that expansion of copper production through the startup of new mines is inhibited. Owners of a large undeveloped orebody would have to decide before going into production whether to sell the concentrates offshore, which has many problems, whether to try one of several unproved chemical processes for producing refined metal from concentrates or embarking on the construction of a traditional pyrometallurgical plant in the face of considerable uncertainty over the pollution standards that eventually must be met. The situation is such that not only is the present rate of U.S. copper production threatened but the ability to meet projected increased demand in the years ahead may have been severely retarded.

Jan 4, 1973

By A. B. Kinzel

MUCH work has been done recently in an attempt to analyze the physicochemical mechanism involved in the production of steel by the open-hearth process. . This has resulted in reducing the process to a series of interrelated phenomena obeying the usual laws of mass action and diffusion. Of these, the reaction of the iron oxide and carbon in the molten steel is of most interest from a technical point of view as it con-stitutes the main action in the usual steelmaking processes. A. L. Feild1 has formulated a basic differential equation expressing the open-hearth reactions and Hefty has done considerable experimental work on the determination of a number of constants involved in the basic open-hearth reaction. In considering the application of the law of mass action. to the reaction FeO +C ?? CO +Fe, the iron will be taken as constant, as is the case in the open hearth and the carbon monoxide pressure will be assumed' constant at one atmosphere. From this xy = m at equilibrium, where x is the percentage weight of carbon, y percentage weight of iron oxide and m the weight-concentration equilibrium constant. While it is customary for physical chemists to express equilibrium constants in terms of molar concentrations, the constant is here expressed as the product of the percentage-weight concentrations for ease of comparison with the constants quoted by Herty and by Feild, and for more ready applicability to the open-hearth reactions. Herty and his associates have attempted to calculate the value of this constant from data on open-hearth heats. So many variables affect these results that an adequate calculation presents very great difficulties. A value of 4 X 10-2 was first arrived at, but this was later changed to 1.6 X 10-2. Feild, in order to illustrate the operation of the differential equation of the open hearth, has assumed a value considerably lower than Herty's, namely, 1.0 X 10-2, the largest value consistent with certain theoretical

Jan 1, 1929

By John M. Kelly

New Mexico produced 39,751,868 bbl. of oil in 1941 and ranked seventh among the oil-producing states. Its 1941 production established an annual record, exceeding the 1940 record year by 854,498 bbl. The average daily production for the year was 108,909 bbl. The average daily non-marginal well allowable for New Mexico on Jan. I, 1941, was 36 bbl.; at the close of the year it was 43 bbl. The average daily pipe-linc runs were approximately 3 per cent less than the allocations of the New Mexico Oil Conservation Commission, which followed closely the recommendation of the United States Bureau of Mines in setting the daily outlet demand. The production in Lea County was 34,333,448 bbl.; Eddy County, 5,009,354 bbl.; and northwestern New Mexico (San Juan and McKinley Counties), 406,306 barrels. The total number of completions in the state was 402, of which 301 were oil wells, 19 gas wells, and 82 dry holes. Drilling during 1941 was 68 per cent of 1940, and the ratio of dry holes to producers, I to 4, was the greatest since 1935. Of these dry holes 43 were drilled in proven fields and 39 were wildcats. One new oil field and one new gas field were discovered as a result of the 1941 wildcatting program. However, numerous extensions were made to the existing fields, which, although they were called extensions to proration areas, were in reality field discoveries, being on separate geologic structures. Southeastern New Mexico Lea County The Monument field was the largest producing field in Lea County, with 6,973,808 bbl. It was closely followed by the Eunice field, with 6,644,181 bbl.; Vacuum field, with 4,800,608 bbl. and Hobbs, with 3,624,159 bbl. Hobbs field, however, still has the largest total recovery, this being 97,407,929 bbl. at the end of 1941. The new oil-field discovery in Lea County during 1941 was the Salt Lake field, T. 20 S., R. 33 E. The discovery well was Leonard-Welch State No. I, NW. NW. of sec. 18, T. 20 S., R. 33 E. This well was drilled to a total depth of 3103 ft. and was completed for an initial production of 250 bbl. per day pumping. The oil is 26" gravity and the producing horizon is in the San Andres limestone of Permian age. The discovery well was completed on June 22, 1941, and since that date four more producers have been completed, with no failures. The area is about 10 miles north-west of the Lynch pool, to which the oil from this field is being trucked because there is no pipe-line connection. The greatest drilling activity during 1947 was in the Maljamar field of western Lea County, with 62 completions, 59 being oil wells and 3 dry holes. The limits of this pool are now being defined on the north and south but to date have not been defined either to the east or west. The total number of 40-acre oil-producing units in the field at the close of the year was 158. On April I, 1941, a pressure-maintenance project was installed at the southern end

Jan 1, 1942

By John M. Kelly

New Mexico produced 39,751,868 bbl. of oil in 1941 and ranked seventh among the oil-producing states. Its 1941 production established an annual record, exceeding the 1940 record year by 854,498 bbl. The average daily production for the year was 108,909 bbl. The average daily non-marginal well allowable for New Mexico on Jan. I, 1941, was 36 bbl.; at the close of the year it was 43 bbl. The average daily pipe-linc runs were approximately 3 per cent less than the allocations of the New Mexico Oil Conservation Commission, which followed closely the recommendation of the United States Bureau of Mines in setting the daily outlet demand. The production in Lea County was 34,333,448 bbl.; Eddy County, 5,009,354 bbl.; and northwestern New Mexico (San Juan and McKinley Counties), 406,306 barrels. The total number of completions in the state was 402, of which 301 were oil wells, 19 gas wells, and 82 dry holes. Drilling during 1941 was 68 per cent of 1940, and the ratio of dry holes to producers, I to 4, was the greatest since 1935. Of these dry holes 43 were drilled in proven fields and 39 were wildcats. One new oil field and one new gas field were discovered as a result of the 1941 wildcatting program. However, numerous extensions were made to the existing fields, which, although they were called extensions to proration areas, were in reality field discoveries, being on separate geologic structures. Southeastern New Mexico Lea County The Monument field was the largest producing field in Lea County, with 6,973,808 bbl. It was closely followed by the Eunice field, with 6,644,181 bbl.; Vacuum field, with 4,800,608 bbl. and Hobbs, with 3,624,159 bbl. Hobbs field, however, still has the largest total recovery, this being 97,407,929 bbl. at the end of 1941. The new oil-field discovery in Lea County during 1941 was the Salt Lake field, T. 20 S., R. 33 E. The discovery well was Leonard-Welch State No. I, NW. NW. of sec. 18, T. 20 S., R. 33 E. This well was drilled to a total depth of 3103 ft. and was completed for an initial production of 250 bbl. per day pumping. The oil is 26" gravity and the producing horizon is in the San Andres limestone of Permian age. The discovery well was completed on June 22, 1941, and since that date four more producers have been completed, with no failures. The area is about 10 miles north-west of the Lynch pool, to which the oil from this field is being trucked because there is no pipe-line connection. The greatest drilling activity during 1947 was in the Maljamar field of western Lea County, with 62 completions, 59 being oil wells and 3 dry holes. The limits of this pool are now being defined on the north and south but to date have not been defined either to the east or west. The total number of 40-acre oil-producing units in the field at the close of the year was 158. On April I, 1941, a pressure-maintenance project was installed at the southern end

Jan 1, 1942

By W. C. Coffin

Fire-brick stoves have become a necessary part of the modern coke blast-furnace equipment, and are also superseding the cast-iron pipe stoves in anthracite- and charcoal-furnaces. The brick stoves in general use are of either the Cowper or Whitwell type, or modifications of these bearing the names of those who invented the alterations from the original types rather than any real departure from then]. All these stoves have approximately the same valve-equipment and follow the same line of operation. The waste gas from the furnace enters at one port and burns in a single combustion-chamber, and the heated products are drawn through the various passe; in the brickwork to a stack of proper height to create the necessary draught. The last passes of these stoves receive a very small percentage of the heat from the gas, owing to their extreme distance from the combustion-chamber; and this chamber also suffers great deterioration in the attempt to force the heat into the farthest passes. At best, about 70 per cent. of the heat taken up is held in the combustion-chamher and the first down-pass of the Whitwell stoves. Mr. Hugh Kennedy, Manager of the Isabella Furnaces, Pittsburgh, Pa., who has had a large experience with the fire-brick hotblast stoves, was so strongly impressed with the fact that but about thirty per cent of the brick of the average stove were doing proper duty as heat-agents, that, after careful study and experiment, he had three 20- by 60-feet stoves constructed with a view of more uniformly heating all the brick. In these the general lines of the Whitwell stove are followed, with the blast-connections unaltered, but gas is introduced at the bottom of each pass, and outlets are provided at the top, so that the gases have a direct natural draught in each pass and the highest heats are obtained at the bottom instead of the top. The natural tendency being toward the reverse condition, the brickwork soon acquires an almost uniform temperature.

Jan 1, 1893

By J. E. Johnson

OF the many items of information necessary to the successful management of the blast-furnace, few are more important than knowledge of the location and movement of the stock: line:—whether the furnace is full and has been kept so; whether the stock is settling regularly or slipping; and, if slipping, how often it has slipped, at what times, and how far at each time. To obtain these data, a man is sometimes stationed at the top of a pair of mechanically-filled furnaces, sim-ply to watch and gauge them by hand in the old-fashioned way. A more recent practice is the suspension of test-rods from ropes leading over pulleys to the ground-level, where the ropes are mound on small drums with graduated peripheries and provided with crank-handles, whereby the skip-man or some other person can quickly and conveniently gauge the position of the stock-line in the furnace. I believe the credit for this great improvement belongs to Messrs. McClure $ Phillips of Sharon, Pa., who were, as far as I know, the first to apply it, and who have a patent for it. The valuable indications gained by application of the Uehling pyrometer to the down-comer are not to be ignorcd; but the information thus furnished is somewhat indirect, and there is no scale for the translation of " top-temperatures " into " feet down." Moreover, this apparatus, as a whole, is delicate, and the cost of installation and maintenance is high. If the record furnished by the Uehling pyrometer is not in the most desirable form, the test-rods, on the other hand, give no record at all, except through the memory or notes of a man who, to say the least, is not gauging continuously, and who may omit to report an improperly low stock-line, if it be due to a fault of his own.

Jan 1, 1906