Search Documents

By I. Cornet

With the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that the notch sensitivity of magnesium alloy extrusions be further investigated and the influence of various factors upon notch sensitivity be noted. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. The work discussed herein was done under "Restricted" Project NRC-21, reported in Dec. 1943~; it has been released for publica-tion by the O.S.R.D. Scope of the Investigation The notch sensitivity of various magnesium alloy extrusions was determined under axial tension, and also under several conditions of nonaxial tension. Hardness, grain size and other metallographic features were observed; stress-strain data were obtained, and the chemical compositions of the alloys were determined, in order to correlate these quantities with thc notch sensitivity. Notch sensitivity under axial tensile load was determined for a few specimens which had been cold worked to various degrees by tensile prestraining. Magnesium alloy extrusions studied included Dowmetal 0, X, J, and A(. For comparison, extrusions of aluminum alloy 24s-T, cast bars of aluminum alloy 122-T2, and cast bars of magnesium alloy C were also tested. The specified chemical composition of these alloys is given in Table I. All bars tested were within specification limits of composition. Investigation of thc tensile notch sensitivity of various magnesium alloy extrusions, under conditions of axial and eccentric load, showed little or no correlation with stress-strain or other conventional data. Since the many uncontrolled variables present might mask significant relationships, one alloy was selected for intensive study. Magnesium 0 alloy extrusions were subjected to experimental heat treatments, and the ,Changing hardness, tensile strength, microstructure, and notch sensitivity observed. Experimental Techniques and Procedures Tensile Testing Bars used for axial loading were machined with % in.- and with 34-in. minimum diam1 and included specimens with 60" V notches (Fig I and 2). Each V-notched specimen was roughed out carefully and then finished with a honed tool. These Y-notched bars were sampled frequently, sectioned, polished, and examined at 500 X magnification to control

Jan 1, 1949

YEAR OF ELECTION 1913. FRANK DAWSON ADAMS, Montreal, Canada. 1921. WILLIAM CUTHBERT BLACKETT Sacriston, Durham, England. 1920. HENRY STURGIS DRINKER Merion Station, Pa. 1933. KARL EIKERS NEW YORK, N. Y. 1922. FEDERICO GIOLITTI Torino, Italy. 1906. SIR ROBERT A. HADFIELD London, England. 1928. JOHN HAYS HAMMOND New York, N. Y. 1921. FRANK WILLIAM HARBORD London, England. 1917. HERBERT HOOVER Washington, D. C. 1905. HENRI LECHATELIER Paris, France. 1931. WALDEMAR LINDGREN Cambridge, Mass. 1921. C. McDERMID London, England. 1913. EZEQUIEL ORDONEZ Mexico City, Mexico. 1911. ROBERT H. RICHARDS Cambridge, Mass. 1934. T.A. RICKARD Victoria, B.C., Canada 1933. ALBERT SAUVER Cambridge, Mass.

Jan 1, 1934

By H. K. Work, H. B. Emerick

IN the past year the steel industry underwent an abrupt conversion from a war tempo to a highly competitive peacetime schedule. It is still too early to gain a comprehensive picture as to which of the measures in production metallurgy, that made the war effort so successful, will remain in the postwar production of steel, but many of them undoubtedly will fill an important place after the war. Considerable speculation has developed regarding the disposition of the war-born production facilities of the steel industry. These include new open-hearth and electric furnaces, as well as vast numbers of auxiliary, supplementary, and balancing units that increased and speeded up production beyond the normal capacities of existing melting furnaces and finishing mills. Although these facilities were installed primarily to help meet war requirements, consideration was also given, in planning, to their possible peacetime use. The new equipment is generally modern and efficient, and it seems reasonable to suppose that strategically located units will gradually be absorbed by various steel companies to supplement their own facilities, or to replace in kind, obsolete and inefficient equipment now ready to be scrapped. Some, however,

Jan 1, 1946

By Charles Macdonald

WROUGHT-IRON eye-bars for bridges and roofs, designed upon what is known as the pin connection system, have been successfully manufactured in this country for some years. The most approved methods employed have been the hydraulic upsetting process, and by die-forging under a hammer. In upset eyes the fibre of the iron is necessarily much distorted ; and in bars of considerable size, this disturbance seriously impairs the strength of the connection. Mr. Collingwood, in discussing my paper on "Proportions of the Heads of Eye-bars," read before the American Society of Civil Engineers, Jan. 21st, 1874, submitted sketches of certain bars intended for the anchorage of the East River bridge, which had been exposed to the action of sulphuric acid a sufficient length of time to thoroughly cleanse the surfaces, and expose the condition of the fibre. These sketches are here reproduced for the purpose of illustrating the effect of this methpd of manufacture. In Figs. 1, 2, and 3, it will be observed that the fibres at A, and E, have been folded back upon themselves and otherwise twisted and disturbed, in a manner not calculated to inspire confidence in the integrity of the connection. To compensate for this defect, a large excess of metal is thrown into the eye; but a method of manufacture which involves such a necessity, even although it be the one giving the best results thus far, all things being considered, is far from being perfect.

Jan 1, 1879

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period April 1 to 15. William B. McKinley, New York, N. Y Collier Cobb, Chapel Hill, N. C. C. W. Goodale, Butte, Mont. E. P. Fleming, Guayacan, Chile. D. C. Brown, San Luis Potosi, Mex. Albert Sauveur, Cambridge, Mass. W. H. Rettie, Yonkers, N. Y. H. M. La Follette, La Follette, Tenn. Mark B. Kerr, San Francisco, Cal. E. Fleming L'Engle, New York, N. Y. H. W. Turner, San Francisco, Cal. H. Garlichs, St. Louis, Mo. Frank M. Leland, Mackay, Idaho. Henry Hay, London, England. Sir Robert Hadfield, London, Eng. Edward J. Way announces that his agreement as consulting engineer in South Africa for the Anglo-French Exploration Co., Ltd., having terminated, he will engage in professional consulting work with headquarters at 135 Cullinan Buildings, Simmonds St., Johannesburg, South Africa.

Jan 5, 1914

By ALFRED D. FLIWN

ENGINEERING COUNCIL is not "about to die," as some persons are saying. Through a natural and foreseen reorganization, Council is entering a new stage of existence with enlarged power for usefulness. Its early constituents have made it possible for many more of their fellow engineers and men of other technical vocations -to take a- share in its activities, responsibilities and support. A new organization is being set up, but it is really a new embodiment of the same spirit of service. Another step is being taken toward the full acceptance by the technical professions of their obligation to the public and to one another for those services which can -be rendered only through effective organization. A brief retrospect is timely. Engineering Council was established in the spring of 1917, as a department of United Engineering Society in response to requests of its Founder Societies. .It followed various attempts of these societies to deal through joint committees with public questions affect¬ing engineers -and with inter-society affairs. These attempts had very limited results. In the new by-laws adopted by United Engineering Society, the purposes and-powers d-powers of Engineering Council were thus defined: "To provide for convenient cooperation between the four Founder Societies, for the proper consideration of questions- of general interest to engineers and to the public, and to provide the means for united , action upon questions of common-concern to engineers.

Jan 1, 1920

By W. N. Miner, R. O. Elliott

Electrical-resistivity )measurments were made be-trueetz room temperatrive and 1.5 oK on five different stocks of cerium metal, and the results were correlated with the types, amounts, and distribution of the impurities present. Magnesium, which appeared to be distributed as a solute throughout the cerium matrix, was found to have a large effect on the residual resistivity, 1 at. pct Mg being sufficient to increase the residual resistivity by about 10 microhm-cm. The formation of ß by repeated thermal cycling between room temperature and liquid-helium temperature is attributed to the deformation and faulting that occurs during the ? D a transformation. In preparation for starting a proposed study of cerium-rich alloys, we examined samples from severa1 stocks of cerium metal in order to choose the purest stock for future use in making the alloys. Low-temperature electrical-resistivity data were used to gain initial information about the purities of the stocks. Additional information was subsequently obtained from chemical analyses, density measurements, optical metallography, and electron-micro-probe analyses. Cerium that has been annealed at high temperature and cooled to room temperature has the fee crystal structure (? phase) with a = 5.16Å. When cooled further, in the region between about 250" and 150°K, some of the fee phase transforms to the double hcp form (ß phase) with a = 3.68 and c = 11.92Å. The remainder of the room-temperature fee form (and perhaps some of the hexagonal phase) transforms electronically in the vicinity of 100° K to the more dense or "collapsed" fee form (a phase), a - 4.85A, by transferring about 0.5 electron per atom from the 4f level to the valence band. Very little work related specifically to the effects of impurities on the physical properties of cerium has been reported in the literature. Gaume-Mahn1, 2 has studied the effects of calcium, magnesium. iron, silicon, and tantalum on the electrical resistivity and magnetic susceptibility of cerium between 60o and 300°K. Gschneidner, Elliott, and McDonald3 have discussed the effects of total impurity content on the hysteresis of the a —? (reversible) transformation and on the formation of the 4 and "a-? intermediate" phases. Smith and Morrice* have reported the effect of total impurity content on the resistivity of cerium at 4 and 293°K. In none of these reports, however, is it apparent that the distributions of the impurities were determined, L.r., whether the impurities were present in inclusions or in solid solution in the matrix is not mentioned; nor does it appear that the phase purity of the cerium was always considered. In the present study, five different stocks of cerium were involved. One was represented by a single sample of electrowon cerium, which was all that had remained from a stock of high-purity material obtained from the U.S. Bureau of Mines, Reno, Nev., in 1959. The other four stocks were recently purchased from commercial sources and were specified to be 99.9 wt pct pure. EXPERIMENTAL Cerium stocks designated as #1, #2, #4, and #5 were obtained from commercial suppliers for the specific purpose of finding a reliable source of high-purity cerium. Although the purity level of the cerium was specified to be 99.9 pet, the specifications did not include limits as to the amounts of various impurities that would be acceptable. Consequently the chemical analyses of the different stocks varied widely. Stock #3, which had been obtained from the U.S. Bureau of Mines and which was the purest on the basis of chemical analyses, consisted of a single specimen of electrowon cerium. It was included in the examination for purposes of comparison. Table I contains the chemical and spectrographic-

Jan 1, 1968

By W. R. Shimer

IN his valuable report on Finishing Temperatures and Properties of Rails, I Dr. G. K. Burgess, Chief of the Division of Metallurgy, U. S. Bureau of Standards, has begun a line of investigation which should be continued by those interested in the subject, and who have proper facilities for carrying put the work. For the past year or more the Bethlehem Steel Co. has been conducting experiments to learn the effect of rail finishing temperatures on their physical properties and microstructure and the results are here given for the consideration of those interested in the rail situation. . Considerable differences of opinion have been expressed by various authorities, in the past, as to the effect of large or small grain size and high or low finishing temperatures of steel rails on their physical properties and wearing qualities. Low finishing temperatures and, therefore, low shrinkage, have been advocated on the theory that the wearing qualities would be improved. Others have recommended high finishing temperatures. The generally accepted cause for rail failures, due to the development ,of transverse fissures, is excessive wheel pressure on hard rails. One of the causes advanced for hard rails has been that they contain too high per centages of carbon and manganese; another that the rails were finished at too low a temperature, i.e., at or near the critical point. In the experiments herein described the rails were rolled from reheated blooms. All the rail blooms were charged hot in a reheating furnace and brought up to about the original ingot-rolling temperature before rolling into rails. These rails gave better results in deflection, withstood a greater number of drops before breaking, and showed greater ductility, than. rails of identically the same composition and section which were rolled, direct from the ingot. Rails rolled from reheated blooms, finished at somewhat higher temperatures than when rolled direct from the ingot, have a different microstructure, which the writer does not believe is due so much to the difference in finishing temperatures, as to the difference in

Jan 3, 1915

By Rollin E. Hook, Attwell M. Adair

The response of CrzO3 and C~304 to various heat treatments was studied in are-melted iodide chromizim over the temperature range 1000" to 1750°C. These oxides, which are present as impurity phases in this material, were identified by X-ray diffraction teclzniques which were supplemented by optical metallop-aphy. As a function of increasing temperature, Crs04 is first observable in samples annealed at 1300°C and coexists with Cr2O3 (the low-temperature oxide) over a temperature range exceeding 200°C. As the temperature decreases, Cr3O4 dissolves with the concomitant precipttation of Cr2Y2. Both oxides precipitate predominantly at pain boundaries. The reactions which occur are involved with at least ternary equilibria, possibly due to iron which is present as an impurity in arc-melted iodide chromium. HILTY, Forgeng, and Folkman' reported in their investigation of the Fe-Cr-0 system that Cr3O4 (with about 8 pct Fe substituted for chromium) is a primary phase found in alloys with 9 or more pct Cr. They reported that this phase is stable only at high temperatures and that below the liquidus Cr3O4 is disproportionated into Cr2O3 and chromium-rich metal for both Fe-Cr-O alloys and in oxygen saturated pure chromium. Further, they proposed that CrsO4 forms by a peritectic reaction between Cr2O3 and the liquid. On the other hand, Hook, Garrett, and Adair2 found in their investigation of impurity phases formed in "pure" chromium (material consolidated from iodide chromium crystals) that Cr3O4 forms intergranularly and is stable as low as 1500°C which is 375OC below the melting point of chromium. The purpose of the research described herein is to determine the temperature range of stability of Cr3O4, and to show the nature of its decomposition. This further investigation indicates that Cr3O4 undoubtedly occurs in this material as low as 1300°C. The chromium studied was consolidated and fabricated from iodide chromium crystals (ICr-5) and contained Fe r 135 ppm, Si = 20 to 100 ppm, and 0 = 35 to 137 ppm. A complete chemical analysis is given elsewhere.' Annealing was conducted in 1 atm of purified helium and all samples were rapidly cooled (-200°C per sec) by withdrawing them from the furnace hot zone under a high flow rate of helium. The details of the electrolytic-etching technique and electrolytic-digestion techniques for preparation of insoluble residues for X-ray examination are given elsewhere also.' EXPERIMENTAL RESULTS The Starting Material. The as-swaged rod (final swaging done at 900°C) had a wrought grain structure and contained a dispersion of CrzO3 inclusions of maximum particle size of about 2 or 3 p, Fig. 1. The microstructure also contained a dispersed

Jan 1, 1964

Nominating Committee.-On the recommendation of the President, the Board of Directors, at their meeting on Apr. 25,1913, appointed the following Nominating, Committee to nominate officers and directors for next year: John Hays Hammond (Ex-President), Chairman. Robert H. Richards Chairman of Boston Local Section. Richard S. McCaffery, . . . . Chairman of Spokane Local Section. Chester F. Lee Chairman of Puget Sound Local Section. Frederick G. Cottrell, . . . . San Francisco, Cal. Charles W. Goodale Butte, Mont. James W. Maleolmson, . . . . Kansas City, Mo.

Jan 5, 1913

By H.E. Brauer

Among the zinc base alloys used for casting in metal moulds, pnrticularly die casting, those alloys containing aluminum usually together with copper, are probably the most widely used. The reason lies in their desirable mechanical properties and the fluidity and absence of hot shortncss which facilitate ca,sting. Objection to the use of these alloys may be raised on account of the rather frequent instances of failure of a type variously described as disintegration, exfoliation and intererystalline corrosion. In all cases which have come to our kno~vlcdge where the conditionsof service were known, failure has occurred upon cxposurc to moisture and heat varying from a hot moist atmosphere to lligh pressure steam. RIoreover, the alloys described in all such roses contain impurities or alloying metals which the present authors have found to have enormous accelerating effects on intererystalline oxid:~t'ion in zinc-aluminurn alloys. Thus Williams1 experimented with an alloy containing a large percentage of tin exposed in Cuba. Baucr2 reports failure of a boiler plug containing over 1 per cent. of impurities, doubtless lead for the must part, and Rawdon's3 examinations were madc on an alloy containing 0.1 per cent. lead also exyosctl to thc Tropics. No thorough investigation of the nature and cause of this type of failure has been made heretofore, so far as the authors are aware, although Rawdon correctly classified it as internal oxidation. We have, therefore, carried out this investigation in order to det'ermine the exact nature of this phenonienon and the effect of other metals present as impurities or intentional additions in accelerating or retarding it. In the appendix we include a considerable amount of data which may be valuable in selecting an alloy combining good physical properties with high resistance to oxidation. At the time this work was undertaken the best available equilibrium *Investigator, Metal Section, Research Division, The New Jersey Zinc Company. 'H. W. Williams—Jour. Am. Inst. of AIet,als, Vol. 11, p. 221 (1917). 2o. Bauer—ZeiL, fiir i'vletall Kunde, Vol. 12, .No. 7, pp. 129-31 (1920). 3H. S. Rawdon—Trans. Am. Elcctrochcmic.al Society (1921).

Jan 1, 1923

By H. E. Brauer

Among the zinc base alloys used for casting in metal moulds, pnrticularly die casting, those alloys containing aluminum usually together with copper, are probably the most widely used. The reason lies in their desirable mechanical properties and the fluidity and absence of hot shortncss which facilitate ca,sting. Objection to the use of these alloys may be raised on account of the rather frequent instances of failure of a type variously described as disintegration, exfoliation and intererystalline corrosion. In all cases which have come to our kno~vlcdge where the conditionsof service were known, failure has occurred upon cxposurc to moisture and heat varying from a hot moist atmosphere to lligh pressure steam. RIoreover, the alloys described in all such roses contain impurities or alloying metals which the present authors have found to have enormous accelerating effects on intererystalline oxid:~t'ion in zinc-aluminurn alloys. Thus Williams1 experimented with an alloy containing a large percentage of tin exposed in Cuba. Baucr2 reports failure of a boiler plug containing over 1 per cent. of impurities, doubtless lead for the must part, and Rawdon's3 examinations were madc on an alloy containing 0.1 per cent. lead also exyosctl to thc Tropics. No thorough investigation of the nature and cause of this type of failure has been made heretofore, so far as the authors are aware, although Rawdon correctly classified it as internal oxidation. We have, therefore, carried out this investigation in order to det'ermine the exact nature of this phenonienon and the effect of other metals present as impurities or intentional additions in accelerating or retarding it. In the appendix we include a considerable amount of data which may be valuable in selecting an alloy combining good physical properties with high resistance to oxidation. At the time this work was undertaken the best available equilibrium *Investigator, Metal Section, Research Division, The New Jersey Zinc Company. 'H. W. Williams—Jour. Am. Inst. of AIet,als, Vol. 11, p. 221 (1917). 2o. Bauer—ZeiL, fiir i'vletall Kunde, Vol. 12, .No. 7, pp. 129-31 (1920). 3H. S. Rawdon—Trans. Am. Elcctrochcmic.al Society (1921).

Jan 1, 1923

By Hans Lundberg

N OT so long ago, the discovery of an orebody took place only by accident. At the present time mineral deposits, even though concealed, may be revealed by their physical or geophysical characteristics, considered in connection with geological studies. Geophysical methods are based on sound, scientific principles and in no sense partake of the mysteries of "divining-rod " methods. Geophysical methods are divided into two main groups: Group I: Methods where fields of force surrounding mineral deposits are investigated (magnetic, gravitometric, electric) ; Group I1 : Methods where fields of force are applied (produced) and anomalies caused in these fields by mineral deposits are recorded (electric, seismic). By methods belonging to Group I, the investigation of the fields of force may be brought to an astonishing degree of accuracy by means of highly sensitive and delicate apparatus (torsion and magnetic balances) ; at least, in simple cases these methods have proved to be of great value.

Jan 1, 1925

By George Lehman

THE Inspiration Consolidated Copper Co. had an orebody at Miami, Ariz., of close to 100,000,000 tons of low-grade copper ore, and the method of mining this ore most profitably was of great importance. The selection of a method was practically limited to a "top-slicing," a "shrinkage-stope" or a "caving" method. The "top-slicing" method would give a high extraction of the developed ore, at a high mining cost, and the ?shrinkage-stope" or "caving" methods ) a lower extraction of, the developed ore, at a lower mining cost. ORE-DRAWING TESTS To decide on the method to be used it was necessary to know about what extraction of the ore could be obtained by the "shrinkage-stope" or "caving" methods. As no definite information regarding the question was available at the time, C. E. Mills, the general manager, thought that some information could be obtained by experimenting in drawing ore, covered with capping, from an experimental box. Some work had already been done along these lines by W. C. Browning for the Inspiration Copper Co. and by myself for the Live Oak Development Co. The idea was to represent as nearly as possible, in the experimental box, the conditions within an area of caved stopes of caved ore all ready for drawing. That is, the area was supposed to represent a semibroken mass with the capping above it in the same condition and ready to follow the ore downward as it was drawn out of the chutes under the ore. To represent the above condition, in the experimental box, crushed ore from the mine was placed in it to a given height, and red barren capping from the mine was placed on top of the ore.

Jan 9, 1916

By C. C. Harris

The characteristics of some common size distribution equations are critically discussed. A generalized form of several well-known size distribution equations is obtained from a differential equation describing statistical distributions. The equation contains three parameters and can describe the major features of size distributions in the fine and the coarse size regions. A graphical method for its implementation is provided. The application of this and other equations to sets of data are compared both for the quality of fit and from a comminution kinetics viewpoint. If a narrow size range of a brittle material is broken sufficiently to obliterate the feed sizes, but not so severely that excessive secondary breakage occurs, a plot of cumulative fraction by weight undersize (Y) vs. sieve size (X) on a log log grid (sometimes called the Gates-Gaudin-Schuhmann plot)1-3 gives a straight line of slope ~ 1 over much of its range. On closer inspection, deviations in the extreme coarse range covering perhaps 10 to 30% of the total sample may be apparent (frequently, a change in slope from ~ 1 to a value different from unity) together with over-all slight irregular departures from a smooth line. One model of breakage postulates that the same fracture pattern persists throughout all size ranges.4 The fracture pattern is characterized by the slope of the line on a log log grid. Accordingly, a distribution of sizes broken in the manner specified earlier is expected to produce a size distribution having the same slope as that of a broken narrow size range. Additionally, the slight irregularities mentioned above should even out in the summation process, giving a smooth straight line of slope ~1 on a log log plot. This idealized state of affairs does not, however, describe the distribution of a multi-event process such as that for a tumbling mill product. On the average, these curves (plotted again log log) tend to have a slope in the fine region different from and usually less than unity,5 while the coarse size region curves with increasing slope for cases of mild reduction, and with decreasing slope when moderate or severe size reduction has occurred. In addition, there are usually slight irregular deviations from a smooth curve. Most curves display two distinct regions — fine and coarse — and a few curves show one or more intermediate regions. Feed size studies6,7 show an effect which theory is required to explain. For the same material, mill loading and other operating conditions, and the same time of grinding, plotting the dimensionless ratios Y vs. X/(feed size) does not reduce the size distribution data to the same curve. Y vs. X does not correlate the coarse region, but it can provide a crude correlation of the fine region which improves as size diminishes and as grinding time increases. The size distribution in the coarse region is somewhat more dependent on the feed size than is the distribution in the fine region wherein the degree of dependence diminishes as time proceeds; the distribution of sizes in the fine region are determined largely by the nature of the material and the comminution conditions. A comprehensive model of comminution must recognize that several different patterns or modes of breakage can occur in a mill; 5,8,9 that there can be some selection in that some size ranges are broken more than others; and that, while some particles may be the product of a single fracture event, or may even remain unbroken, others result from multiple rebreak-age. Thus, breakage in a tumbling mill is more complex than the Schuhmann4 model admits in that several different types of comminution micro-events* occur rather than just one type, and these events, though different in size scale, are of the same overall pattern as that which is visualized by the model. The concept of an average comminution micro-event has, therefore, a mathematical rather than a physical connotation, at least for tumbling milling. Equations with which to describe particle size distributions have been sought for over half a century.10-13 No equation presently in general use was first derived from an analysis of the statistical mechanics of breakage; whatever theoretical basis the existing

Jan 1, 1969

By Craig R. Barrett, Oleg D. Sherby

The creep characteristics of four pure metals with widely Varying stacking-fault energies (silver, copper, nickel, and aluminum) were evaluated above 0.5Tm. Creep tests were performed under conditions of constant atomic diffusivity and constant stress over the elaslic modulus. The sleady-state creep rate, Es, was found to he a funclion of the THE most common empirical representation of the steady-state creep rate, Es, at high temperatures and intermediate stresses is of the form where a is the applied stress, E is an elastic constant, A and n are constants (n is typically stacking-fault energ, y, such that Es is proportional to y3,5. In addition, it was uncovered that the primary creep strain and the strain to fracture increased with increasing y, and that the ratio of initial to steady-state creep rate decreased with increasing y. about 5), Q is the activation energy for creep (usually equal to that for self-diffusion), and kT has its usual meaning. sherbyl and McLean and ale' have used this expression to correlate creep data for a number of pure metals. An interesting aspect of Eq. [I] is the absence of any dependence on the stacking-fault energy. While most creep data seem to obey the stress and temperature dependence predicted by Eq. [I], when data for several metals are put on a master plot they do not fall on a common line but form a band. The width of this band corresponds to a variation in Es of 102 to l03. sherbyl attempted to explain this band by assuming that a grain-size effect was present which led to the observed variation. On the other hand, Felt-

Jan 1, 1965

By A Andersen

DURING an investigation of the copper-rich portion of the copper-silicon-iron system as part of an extensive research program on P.M.G. alloys, which was begun in 1937 in the research laboratory of the Phelps Dodge Corporation, it became apparent that the binary copper-silicon system below 7 per cent Si needed revision, therefore an investiga-tion was undertaken. Both X-ray methods and microscopic technique were employed. Despite the many investigations that have the clarification of this sys-tem as their object, no two successive reports on the system have agreed in placement of the alpha-phase solubility limit, and uncertainty about the secondary phase first to appear has been voiced several times.3,4,5 It was therefore not surprising, when T. Isawa's6 and M. Okamoto's7 works were reported at the time we were finishing up our experimental work, to find essential disagreement between their results and ours. But when C. S. Smith's latest work on the copper-silicon system8 was published just as we were finishing our laboratory report, it was indeed gratifying to find that the latter's diagram and ours checked in all essen-tial features, except the temperature of the peritectic line above 830° C. Many attempts were made to retain the beta phase during the present investigation, but none was successful. Isawa,6 however, reports that he has been able to obtain X-ray photograms of the beta phase. The structure, he states, is body-centered cubic with a lattice constant of 2.848 A.. at 7.2 per cent Si. Okamoto7 and Smith8 both use the designation Kappa for the hexag-onal phase, and to avoid confusion this designation will be adhered to in the present paper.

Jan 1, 1939

By Gordon E. Agar

Several correlations have been proposed to relate energy consumption and size reduction in comminution, and although these are arrived at from different starting points, it is postulated that they are all statements of the same basic concept. To test this postulate, the dry ball mill grindability of langbeinite was determined, and the results were analyzed according to the various methods. An examination ' of the energy-particle size relationships proposed in the recent past revealed that they had much in common. In fact, the conclusion was tentatively drawn that these expressions were essentially the same, even though they were arrived at from quite different basic premises. The equations attributed to Charles2 and Holmes3 were shown to re- duce to the same single equation, W - A K-3, and the simulated continuous test used by Maxson et al.4 was shown to give the best experimental value of the required empirical parameter, ß. Furthermore, the size distribution parameter a in the Schuhmann equation, y - (x/K)2, was shown to be equal to ß in many cases. The kinetic approach used by Arbiter and Bhrany5 should give the same results as the Maxson test procedure; however, the batch operation used by Arbiter and Bhrany could not produce data that would be as precise as the simulated continuous technique. To test the validity of these conclusions, the simulated continuous method was used to obtain data on the dry grinding of langbeinite. The results are discussed in terms of the various equations and approaches. APPARATUS AND MATERIAL A ball mill with internal dimensions of 17.5 cm (6 7/8 in.) in length by 19.4 cm (7 5/8 in.) in diam was loaded to 50% of its volume with balls 3.2 cm in

Jan 1, 1969

By S. A. Levy, J. D. Wood, J. F. Libsch

A study of the preparation and characteristics of a sevies of Fe-C-N alloys has been conducted. X-ray, microhardness, and metallographic data from a series of single-phase alloys produced by controlled nitriding of carburized foils are reported. The existence of a, y', and E carbonitride has been confirmed and it has been found that y' is the hardest of these three phases. These results have been used to interpret the structures observed in nitrided steels. ThIS paper represents the second phase of a three-part study concerning combined nitriding and induction hardening. The first part' reports the engineering properties (depth hardness, fatigue, corrosion, and tempering resistance) obtained when seven different steels were subjected to the combined surface hardening treatment. The present paper concerns the nature of a series of single-phase alloys prepared by controlled nitriding of carburized foils. The objective was to simulate the various layers present in the as-nitrided steels. A third paper will report data concerning induction hardening of the foils and will attempt to set forth a mechanism for the high hardness obtained with the combined treatment. Studies of nitriding generally fall into three categories. The first were performed with bars using conventional nitriding procedures, thus yielding a nitrogen gradient and a series of phase layers near the surface.2-6 Such studies were complicated by the presence of the nitrogen gradient, for it was difficult to correlate microhardness and X-ray data with chemical composition. There were always complications due to penetration of the X-ray beam which yielded data influenced by underlying layers. Similar difficulty was experienced in taking hardness readings on a tapered specimen or in isolating various layers by machining. A second group of investigations was primarily concerned with establishment of regions in the Fe-N7,9,10 or the Fe-C-N phase diagram.8 These were performed with powder specimens which were nitrided in am-monia-hydrogen mixtures to produce a series of single-phase specimens. Unfortunately, the powder specimens were not amenable to either microstruc-ture or microhardness study. The third was essentially a compromise of the first two. Bose and Hawkes," using 0.005-in.-thick iron foils, were able to obtain microhardness, microstruc-ture, composition, and X-ray data on Fe-N alloys of eutectoid composition by equilibration in ammonia-hydrogen mixtures at 1290°F. To obtain a better understanding of the nitriding process and the characteristics of the phases in ni-trided plain carbon steels, the present investigation was undertaken. The investigation was patterned after that of Bose and Hawkes with the exception that nitriding was performed at 930°F (below the eutectoid temperature), as in the case of conventional nitriding. In addition to gaining some understanding of the source of high hardness of nitrided and induction-hardened steels, found in a previous study,' this investigation was concerned with the possibility of controlling the phases present in a nitrided case through the use of ammonia-hydrogen mixtures. Knowledge of the properties of each phase and the conditions necessary for its production could make it possible to avoid undesirable surface layers in nitriding. EXPERIMENTAL PROCEDURE Specimen Preparation. A specimen thickness of 0.005 in. was selected to insure that a uniform nitrogen concentration could be obtained in a reasonable length of time by equilibration in an ammonia-hydro-gen atmosphere. The starting material was a vacuum-cast ingot of pure iron, the major impurities of which were: C, 0.003 pct; 0, 0.014 pct; S, 0.004 pct; N, 0.003 pct.* 'Compositions are quoted as weight percent except as noted. The ingot was heated to 1500°F in a nitrogen atmosphere and forged to a slab 0.25 in. thick. The material was then reduced to 0.005 in. by alternately cold rolling and annealing in a nitrogen atmosphere at 1600°F. This material was divided into five groups of specimens which, after carburizing, yielded the following carbon contents: 0.003, 0.28, 0.36, 0.46, and 0.74 pct C. The carburizing was performed by the Leeds and Northrup Research Laboratories, using a controlled "carburizing potential" which yielded a uniform carbon concentration throughout the cross section.

Jan 1, 1970

By S. H. Penn

One of the more challenging aspects of the unfolding age of space travel centers about the opportunity for man to use the natural resources of other worlds. The first of the extraterrestrial worlds to be exploited will be the moon. After only a scant few thousand years of scratching the earth's crust, man will embark upon a venture that for centuries has excited the imagination of many (while staggering that of most) and may become a reality within the next decade. There has never been a time when so much money and effort will have been expended to exploit an area about which so little is known. Paradoxically, this effort combines much of the detached objectivity so typical of our analytical time with the proverbial optimism of the indefatigable prospector. As the earliest manned lunar missions will be brief and exploratory in nature, astronauts will not be expected to attempt to exploit any of the possible lunar natural resources. In later missions, with a more extended period of time available for the astronauts to stay on the moon, it may be desirable or even necessary to "live off the land". The resulting exploitation of lunar resources will be intended primarily to reduce the dependence of manned missions upon terrestrial logistic support and to reduce the cost of maintaining lunar bases.

Jan 3, 1966