Search Documents

By Stephen Royce

[PAGE Ground Movement Adjacent to a Caving Block in the Climax Molybdenum Mine (TP 2000 by JOHN W. VANDERWILT, Min. Tech., May 1946. Discussion by STEPHEN ROYCE and the Studies of the Design of Shaped Explosive Charges and Their Effect in Breaking Concrete Blocks (TP 2157 by GEORGE B. CLARK, Min. Tech. May 1947. Discussion by PHILIP B. BUCKY, V. H. CLARK, E. D. GARDNER, M. H. HAWKINS, H. L. WALKER, and the author) 2 See TP 2377, Min. Tech., May 1948 for discussion of San Manuel ProsPect (TP 2255 by H. J. STEELE and G. R. RUBLY, Min. Tech., Sept. 1947. Discussion by L. KENNETH WILSON, ELDRED D. WILSON and the authors)] Ground Movement Adjacent to a Caving Block in the Climax Molybdenum Mine STEPHEN ROYCE•-It is interesting to note from B, Fig 2, how closely the subsidence limits approximate to the 60° angle of draw, which is so commonly found to rule in large scale rock subsidence. The tension cracks shown at B are commonly found in the initial stages of subsidence movement and spread like a halo about subsidence limits as movement extends. These tension cracks usually grow into escarpments later on. Apparently from the illustrations and description given, a system of vertical fractures is the predominating weakness in the wall rock at Climax, and therefore both tension cracks and escarpments are prevailingly vertical in attitude. The illustrations in Mr. Vanderwilt's article seem to conform to the general rule that yield by subsidence is heralded by tension cracks which foreshadow the appearance of the subsidence scarps which are both described in the paper and shown in Fig 2. The difference between the B side and the A side of Fig 2 is apparently caused mainly by the vertical fracturing which controls subsidence at Climax as compared to the relatively homogeneous rock formation at A upon which the original figure in Peele's Handbook was based. The draw at B is exactly 60°, while the draw at A is a little flatter. The influence of the vertical fractures explains the difference. The surprising feature is the relatively small deviation from the general 60° draw line, which is about the average of rock subsidence experience. The influence of local fracture systems, faults and bedding in controlling subsidence all the way from extremely low angles of draw to vertical is rather fully discussed in the Peele's Handbook article referred to. The more illustrations of subsidence there are published the better will be our knowledge. The general principles are pretty well established. The wide local differences reflect the effect of local conditions. This paper is a very valuable contribution to the subject, and for the benefit of the mining industry, it is to be hoped that there will be many more such clear and concise presentations. Particularly block caving is apt to be of greatly increasing importance in the future of a mining industry that must meet high labor costs. More examples of block caving from small scale to large scale operations like those at Climax will serve a vital need. JOHN W. VANDERWILT (author's reply)-I would like to thank Mr. Royce for his discussion; however, in his comments the meaning of subsidence, draw and tension cracks is not entirely clear. As used in my discussion of subsidence at Climax, subsidence refers to movements involving appreciable downward displacement. Tension cracks indicate only

Jan 1, 1947

CALAMINE is one of the semiminerals that have great similarity to the metals. It is a very heavy mineral earth of a yellowish color. It is found in Germany near the lead mines and in Italy in a mountain between Milan and Como. It is also found, as I have heard, in other places, as at Fosini in the territory of Siena. I believe that it is almost certain that some exists there because there are many other kinds of minerals there- about, although none is mined there in these times. But this does not mean that it could not be mined or that there is not some there that is real. Someone says that he med to melt what he could find with copper [36v]

Jan 1, 1942

By L. C. Morganroth

Discussion of the paper of L. C. MORGANROTH, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 475 to 481. DAVID B. REGER, Morgantown, W. Va.-I notice in the third paragraph of the first page of the paper, that in mentioning the clays of the Pottsville series, the author says: "The bed of clay found in the latter formation is unique in that flint clay is practically restricted to it. (A variety of flint clay is occasionally found in these upper deposits but this is in such small amounts as to be negligible."). If the author wishes to confine himself to the fire clays of Pennsylvania, as the title seems to indicate, I have nothing to say, but if he wishes to include a discussion on fire clays of the adjoining States which the. subsequent paragraphs of his paper seem to indicate, then I wish to call attention to the fact that there are large and extensive deposits of fire clay in the Allegheny series, immediately overlying the Pottsville in the northern counties of West Virginia. These fire clays have been studied carefully, and described in several reports of the West Virginia Geological Survey, first in the report on Ohio, Brooke, and Hancock Counties, in the northern part of the State; described later ,in the report on Monongalia, Marion, and Taylor Counties, and in the report on Preston County, which followed. In these latter counties (Monongalia, Marion, Taylor, and Preston) there are some beds of fine fire clay, varying in thickness from 6 to 10 or 12 ft., with a content of only 2 or 3 per cent. of fluxing ingredients, and these are of the typical Savage Mountain appearance and also have the typical Savage Mountain fracture. They have been prospected, but not mined a great deal. Several of them have been tested in blast furnaces and furnaces for other purposes, in glass-manufacturing plants, also for firebrick, arid have been found to be very good. They are simply awaiting development, and I merely want to call attention to the fact that there are plenty of them in the Allegheny series still above the Pottsville in West Virginia. There are two or three valuable seams which I have seen in person and have had analyzed in our laboratory.

Jan 5, 1916

By G. B. Pryde

IN laying out a new mine, provision should be made for the ultimate recovery of as much coal in any given bed as is consistent with safety and economic mining. Though each mining district, if not each individual mine, has problems that make the adoption of any hard and fast rule impossible, certain basic principles are adapted to practically all conditions. One of the most vital is the provision for barrier pillars of ample dimensions to protect all haulage and permanent airways during the life of the property. Where conditions permit, room or butt entries should be driven on the strike or slightly to the raise and rooms turned at right angles to said entries. The width of rooms and room pillars is governed by conditions prevailing in the mines under consideration. A safe rule is: In advancing, extract not more than 25 to 35 per cent. of the entire seam; in exceptionally thick seams, considerably less than 25 per cent. should be taken. Rooms usually vary in length from 250 to 350 ft. (76 to 106 m.) with a barrier pillar of not less than 80 ft. between the last crosscut in rooms, and entry and room crosscuts should be driven on sights; room crosscuts should be driven at right angles to the direction of the rooms. In mines under excessively heavy cover or where roof conditions are bad, rooms should be driven narrow and a barrier pillar left at every fifth to tenth room. This barrier should be of such dimensions that one or more rooms, with pillars of usual dimensions, may be turned through it when the barrier is no longer required. Two of the advantages of such a barrier are the protection of the panel against peaking of roof load during pillar extraction and the easy closing of the entry in case of fire.

Jan 2, 1921

By R. B. Basham, C. W. Macune

Very small anomalies in oil well temperatures are detected and measured by recording the difference in temperature existing between two thermally sensitive elements which are Spaced several feet apart on a small diameter carrier and lowered into the bore hole. The elements operate in a balanced electrical circuit, sending only a reference signal to the surface as long as normal gradient temperatures are encountered. When either element enters a temperature disturbance, the circuit is unbalanced and produces large recorder deflections for minute anomalies. The system is highly sensitive to small changes in thermal gradients caused by gas or fluid movements and to the boundaries between beds of different thermal conductivities. Typical logs show successful applications of the process to locating gas and water leaks in casing, gas entry. and gas-oil contact. INTRODUCTION Temperature measurements in oil wells have been made for many years in the search for additional sub-surface data. It has been generally agreed that many conditions in the bore hole cause temperature anomalies which, if located and measured, could yield useful information. But it has been recognized also that many of the irregularities, such as those produced by small water and gas leaks in casing, might be very small and therefore difficult to detect with certainty.' Although tem-perature measurements have been made which show anomalies of less than one degree deviation from normal gradient temperatures, the results are usually uncertain and unconvincing. The general practice, therefore. has been to apply temperature surveys only to well conditions known to produce appreciable disturbances, such as large gas movements and cement hydration. The recent demand for additional data has focused attention on the problem of making dependable temperature measurements in the many instances when anomalies are small but none the less significant. It was for the purpose of detecting these minute irregularities in bore hole temperature that the program described in the following text was undertaken. It is emphasized that this presentation is not offered as a complete study, for the process is still partially experimental. But it is believed that the results obtained thus far will be of interest to the industry and will indicate some of the system's potential usefulness. DIFFERENTIAL MEASUREMENT The chief value of differential measurement lies in the fact that a difference between two factors can be measured with a scale of values best suited to that difference, a scale that might be cumbersome or impractical if applied to the factors themselves. When it is known that all factors will be nearly equal in value, and therefore the differences consistently small, it is possible to select a scale which will permit very accurate measurement of the differences. This advantage is in contrast to the difficulty of measuring small increments of a single variable, where the increment must be measured by a large scale which is suitable for measuring the entire factor. Gradient temperatures are usually measured under this latter condition where temperature measuring apparatus must have a scale extending over the range of expected temperatures, say 50' to 25O°F, and it becomes almost impossible to detect small irregularities of less than one degree. The use of large strip chart recorders and divided multiple ranges tend to amplify the small anomaly and make it more pronounced. But the instability of instruments, both

Jan 1, 1952

By Adolf Gurlt

It has long been known that minute quantities of foreign substances, when alloyed with steel, are capable of materially altering its physical properties. Thus, half a century ago, Faraday and Stodart, in England, discovered in the famous Indian steel, known as " wootz," small quantities of aluminum, from 0.0728 to 0.693 per cent., and attributed its extraordinarily good quality to the presence of such minute quantities of that metal. Since aluminum is now produced by electrolytic means on a large scale and at low cost, its addition to cast-steel has been frequently recommended of late. Chromium was alloyed with steel fifty years ago by the celebrated French metallurgist, Berthier, of Paris, and has recently been successfully applied to the same purpose by Holtzer, of Terre-Noire. In 1860 titanium was alloyed with crucible steel by Robert Mushet, of Coleford, the alloy containing up to 0.50 per cent. of titanium, which was extracted from Norwegian ilmenite. The titanium-steel was much vaunted by him for its excellent qualities. Rhodium, a very rare metal of the platinum series, was maintained by Berthier to improve steel materially in strength and hardness. Manganese has always been held by Sheffield steel-melters to provide steel with excellent qualities, and this influence was quite recently investigated by H. M. Howe and L. Campredon. Nickel was tried as an addition by Berthier, not to speak of gold, silver and platinum ; and nickel-steel has recently been brought into prominence by J. Riley and others, who recommend it for its great strength and toughness, particularly as material for armor-plates.

Jan 1, 1894

By O. L. Kowalke

During the last few years the use of base-metal thermocouples has increased very considerably in various industries, due to the necessity for more precise control of temperatures. The base-metal couple has the advantages of being robust to a surprising degree, cheap as compared with platinum couples, sufficiently accurate for most operations, rapid in indicating changes in temperature, easily renewed or repaired, and of generating a much higher electromotive force than the noble-metal couples. There are, however, some factors, such as indicating and recording instruments, the insulation on the elements, the constancy and homogeneity of the wires, and the resistance to oxidation in the furnace, that limit the. Usefulness of the temperature-measuring device. It is the purpose of this paper to discuss in what manner these factors affect the usefulness of the couples.

Jan 9, 1919

By D. H. Bacon

Nearly all men are too busy with their own affairs to keep informed of the progress in other lines. From time to time we read statistics showing the development in some industry that astonish us; but the feeling of surprise soon fades: to be followed by others that likewise pass away. A short resume of what has been done in one line may be of interest. Down to late in the fifties the ore-product of Lake Superior mas handled over a mule-tram-road to Marquette; now the Duluth, South Shore and Atlantic, the Chicago and Northwestern, the Wisconsin Central, the Duluth, Superior and Western, the Duluth, Mesabi and Northern, the Duluth and Iron Range and the Lake Superior and Ishpeming railroads serve the shippers. Down to nearly 1870 a 700-ton ship was an enormous craft, the loading of which required two days; the unloading being seldom accomplished in that time. In 1871 the largest ore-barge carried 1050 toils and made twelve trips per season. Now the cargoes reach 5000 tons, the loading requiring less than three hours, and the unloading ten hours. Now the mines cover more land than was familiar to even the " timber-cruiser " when the Jackson mine was opened. The annual shipments have grown from a few thousand to 10,000,000 tons, and the ability of the mines to produce is not taxed. Lake-freights are at one-eighth, and rail-freights at one-quarter, of early prices. The deeper waterways, commodious locks and large ships of to-day are in a greater measure due to the movement of ore than to any other cause. Great savings have been made in each detail of each department. The only item of cost that has not been lessened, I am glad to say, is the money paid to men. Wages, measured by what they will buy, are as high

Jan 1, 1898

5. The medal committee may invite nominations from the membership of the Institute, such nominations to be accompanied by an argument in favor of the award and details sufficient for a proper citation to be drawn. This medal has been awarded as follows: 1927—David William Brunton. 1929—John Hays Hammond. 1928—Herbert Hoover. 1930-Daniel C. Jackling. Miscellaneous Prizes Many of the Local Sections have established or administer prizes for the best paper presented within the year by any junior member. Annual Lectures Howe Memorial Lecture The Howe Memorial Lecture, in memory of Henry Marion Howe, Past President of the Institute, was authorized in April, 1923, as an annual address to be delivered by invitation under the auspices of the Institute by an individual of recognized and outstanding attainment in the science and practice of iron and steel metallurgy or metallography, chosen by the Board of Directors upon recommendation of the Iron and Steel Division. The following were the Howe lectures and lecturers for the years indicated: 1924 What is Steel? By Albert Sauveur. 1925 Austenite and Austenitic Steels. By John A. Mathews. 1926 Twenty-Eve Years of Metallography. By William Campbell. 1927 Alloy Steels. By Bradley Stoughton. 1928 Significance of the Simple Steel Analysis. By Harry D. Hibbard. 1929 Studies of Hadfield's Manganese Steel with the High-power Microscope. By John Howe Hall. 1930 The Future of the American Iron and Steel Industry. By Zay Jeffries. Institute of Metals Lecture An annual lectureship was established in 1921 by the Institute of Metals and it has come to be one of the important functions of the Annual Meeting. A number of distinguished men from this country and abroad have served in this lectureship. The roll is quoted below: 1922 Colloid Chemistry and Metallurgy. By Wider D. Bancroft. 1923 Solid Solution. By Walter Rosenhain. 1924 The Trend in the Science of Metals. By Zay Jeffries. 1925 Action of Hot Wall: a Factor of Fundamental Influence on the Rapid Corrosion of Water Tubes and Related to the Segregation in Hot Metals. By Carl Benedicks. 1926 The Relation between Metallurgy and Atomic Structure. By Paul D. Foote. 1927 Growth of Metallic Crystals. By Cecil H. Desch. 1928 Twining in Metals. By C. H. Mathewson. 1929 The Passivity of Metals, and Its Relation to Problems of Corrosion. By Ulick R. Evans. 1930 Hard Metal Carbides and Cemented Tungsten Carbide. By 8. L. Hopt.

Jan 1, 1930

[Steel, iron which is malleable at least in some one range of temperature, and in addition is either (A) cast into an initially malleable mass ; or (B) is capable of hardening greatly by sudden cooling ; or (C) is both so cast and so capable of hardening. Variety A includes also molten iron which, if cast, would be malleable, as do its two sub-varieties, "ingot-iron" and "ingot-steel." (Tungsten-steel is malleable only when red-hot.)] does not seem to fit perfectly the requirement that it shall include all known varieties of steel and exclude everything else. The first requirement, that it shall be malleable at some temperature, is also possessed by some varieties of gun-iron—that is, mottled castriron, of which cannons have been made in the past by the South Boston Iron Co. and others. Gun-iron also meets the requirement (A) in being cast into an initially-malleable mass. The malleability was indeed not great, nor mas it made use of except to demonstrate the quality of the iron, but it approached in measurable degree that of some of the alloy-steels. As for requirement (B), some puddled-irons having from 0.2 to 0.3 per cent. of carbon may be hardened greatly, although this property is [lot utilized.

Jan 1, 1909

By William Hume-Rothery

MR. CHAIRMAN, LADIES AND GENTLEMEN: I need not say how much I appreciate the honor of being asked to lecture to you, and how much I would thank you for your kind invitation. It is encouraging to feel that the abnormal restrictions of the war have been relaxed sufficiently to allow a free exchange of scientists between our two countries, and I hope that some of you will be persuaded to go to England, and to visit us at Oxford, so that I may repay a little of the kindness I have received from you. As this is one of the first lectures since the end of the war, I have thought it well to describe some of the advances in the theory of alloys which were made in the years between the two World Wars. From the point of view of theoretical science, these years have been of outstanding interest in the history of metallurgy. They have been years in which the development of new and more accurate experimental methods has led to the revelation of many new facts. At the same time, the theoretical developments have enabled some of these facts to be viewed as parts of a general scheme, and we may say that some of the foundations of metallurgical science have been laid. This work was naturally stopped by the Second World War, and it can therefore be reviewed as one definite stage in the development of our Science. To illustrate the new advances, I shall deal mainly with the alloys of copper and silver, since these have revealed many of the general principles. SOLID SOLUTION At the beginning of our period, the first steps in X-ray crystal analysis had been taken, and copper had been found to crystallize in the face-centered cubic structure (Fig I). The determination of this structure naturally was of immense importance in the understanding of our subject, because it meant that we were at last in a position to appreciate the underlying structure out of which the crystal of copper was built. The earlier science of metallography had shown that in many alloys of copper the addition of a second metal in not too large proportions resulted in the formation of a homogeneous alloy which was regarded as a solid solution of the one metal in copper. Fig 2, for example, shows the so-called equilibrium diagram of the copper-zinc alloys, and here you will see that there is a solid solution of zinc in copper extending to something of the order 35 to 40 at. pct zinc.

Jan 1, 1947

By Arthur G. Metcalfe

Arthur G. Metcalfe (SOLAR)—Three explanations to account for mechanical nucleation effects are considered in the paper, viz., theories based on fragmentation, agglomeration, and pressure-wave mechanisms. The authors show that none of these mechanisms will explain the results observed with tin and Sn-Pb alloys. A fourth mechanism of nucleation enhancement was developed during work at Armour Research Foundation on casting of beryllium and, although presented briefly on various occasions, the theory has never been discussed adequately. It is believed that this theory will explain many of the observations. Classical homogeneous nucleation theories assume that embryo nuclei are formed in the melt as a result of compositional and/or thermal fluctuations. Stable nuclei are formed when a critical size is reached such that the decrease in free energy for conversion of this volume of melt to solid offsets the increase of surface, energy. The assumption is made that the average properties of liquid and solid metal can be used. In practice this assumption is invalid and indeed is contrary to the postulation of thermal and compositional fluctuations in the melt. Actually the conditions favoring embryo formation bring the seeds of its own destruction—the thermal and compositional fluctuations leave the embryo surrounded by atoms of higher thermal energies and/or by solute atoms that depress the melting point. Any mechanical method of dispersing this destructive

Jan 1, 1964

By S. S. Clarke

THE opening of sheet-ground mines in which the ore beds are only from 7 to 9 ft. thick led the Commerce Mining and Royalty Co. to con-sider mechanical loading, in order to avoid the high cost of hand shovel-ing in such mines. Scraper loaders were chosen because the capital investment would be comparatively low; because they are small enough to be used in low working faces, and because they can be mounted on a mobile carrier.

Jan 1, 1939

By W. A. Olds, H. F. Yancey, M. R. Greer

John Griffen (Consulting Engineer, Pittsburgh)— This paper presents much data offering tentative answers to many technical questions that have been raised by the employment of dense-medium processes and, particularly. by use of the drum-type vessel. It is to be hoped that the Bureau of Mines will publish complete detailed data for the 50 or more tests so that it may be studied and analyzed by everyone interested. Such study will take considerable time and effort. The writer is therefore obliged to confine his discussion to a few points he has noted as being open to question. The data in Table VI which shows the recovery efficiency for the 1 to ½-in. fraction as 100 pct raised a question concerning the accuracy of these calculated figures; washability data on the washed coal and refuse show that such a figure is impossible. When the ash content of the misplaced material in the washed coal is higher than that of the misplaced material in the refuse, recovery efficiency must be less than 100 pct. A etudy of the data In Tables 111, IV, V, and VI suggest that this error probably arose from slight errors in calculating the data in Table V and more probably from the small scale used in plotting the washability curves from the Table V data. Using the size consist data and the weight and ash percentages of individual gravity fractions of each size as given in Tables 111 and IV and the reported recovery of 80 pct of washed coal, a revised Table V was calculated, carrying weight and ash percentages to hundredths of a percent instead of rounding off at tenths. This washability data for each size of Belling-ham reconstituted feed was then plotted on large scale washability curves. From this data the new Table XIV was prepared, which agrees very closely with data shown in Table VI except for two important values, theoretical yields and recovery efficiencies. As will be noted the recovery efficiencies in Table XIV are significantly lower than those given in Table VI. A study was then made of the data showing distribution of the specific gravity fractions to washed coal and refuse. This study indicated that when this distribution was based on the fractions as tested at 0.1-sp gr intervals the number of points obtained were insufficient to establish the distribution curves with reasonable precision, which in turn would affect the accuracy of the values for the specific gravity of separation and the error areas. The data in Tables III and IV of the paper and curves prepared therefrom make it possible for the specific gravity fractions to be subdivided further. This was done using 0.05-sp gr fractions and the distribution data so obtained is given in Table XIV, with resulting values for the specific gravity of separation and the error areas. The writer believes that the derived values shown on Table XIV are more accurate than the correspond-

Jan 1, 1955

By William E. Ford, Edward Salisbury Dana

430. The more important of the special properties of a mineral species with respect to heat include the following: Fusibility; conductivity and expansion, especially in their relation to crystalline structure; change in optical characters with change of temperature; specific heat; also diathermancy, or the power of transmitting heat radiation. The full discussion of these and other related subjects lies outside of the range of the present text-book. A few brief remarks are made upon them, and beyond these reference must be made to text-books on Physics ant1 to special memoirs, some of which are mentioned in the literature (p. 305).

Jan 1, 1922

By A. J. W. Schwandt

Magmont is a venture jointly owned by Cominco American Incorporated of Spokane, Washington and Dresser Minerals, Division of Dresser Industries, Houston, Texas. Cominco American assumed direction of the operation in 1961 and completed exploration, preproduction planning and development, and is now the operating partner managing the operations. The plant has a rated capacity of 4200 tpd and produces in excess of 60,000 tons of lead per year. [ ]

Jan 1, 1970

A three day international mining convention was held At the city hall of Nelson, B. C., June 19-21. It was held under the auspices of the Nelson-Slocan and British Columbia Mining Men's Club, the Northwest Mining Association of Spokane, the Kootenay Mine Owners' Association, assisted by the Spokane Chamber of Commerce, the Vancouver, Chamber of Mines, the City of Nelson, the Associated Boards of Trade of Eastern British Columbia and the Nelson Board of Trade. The technical program was in charge of Columbia Section, American Institute of Mining and Metallurgical Engineers and Western Branch and Kootenay-Boundary Branch, The Canadian Mining Institute. The first day was given over to the judging of mining exhibits and manufacturer's displays; the organization of a branch of the Canadian Mining Institute, and the reception of visitors from Spokane. On Friday afternoon a joint session of the Canadian Mining Institute and the American Institute of Mining and Metallurgical Engineers was held.

Jan 8, 1919

By Roy C. Kirkman

Dear Editor: It is with great pleasure that I read Mr. Howard M. Wells article in the December 1978 issue of MINING ENGINEERING entitled: "Optimization of Mining Engineering Design in Mineral Valuation." Mr. Wells very adequately presents the case and point that there are a great number of variables which must be analyzed during an economic evaluation of an FUND RESOURCE, such as copper or uranium. I wish to take this opportunity to suggest that, given today's economic climate, decision making takes place under conditions of uncertainty and that this uncertainty justifies our need to examine each one of the parameters entered into the evaluation model. It is my contention that the influence of the tonnages and grades as well as their distributions, have the most profound effect upon the results of an evaluation. Everyone concerned with the evaluation of FUND RESOURCES realizes that as metal prices decline or stagnate with sharply rising direct operating costs, cutoff grades (Gc) must increase according to the equation below which Mr. Wells uses: Gc = Total Operating Cost/(Market Price X 20 X Recovery) However, historically, we have seen cutoffs move dramatically lower in both the copper and uranium industries for the past decade. Henceforth, this established the metals industry most important argument for processing greater tonnages of lower grade materials from disseminated deposits (refer to paper by Kirkman, Roy C.). These disseminated deposits, created by either concentration processes (uranium) or dispersion processes (copper, gold, molybdenum), have log-normal grade distributions (Fig 1). Gross profits are rising, but unit profits are falling. The industry has created longevity through economy of scale, i.e., mining vast tonnages of low grade. In order to develop the great tonnages necessary to prove economic viability, we must examine alternatives at the low-end of the tonnage grade relationship. Notice from [Fig. 2] that as we move further to the right away from line A-B drawn tangential to the average grade curve at 45°, total profits will increase (given fixed annual production capacity) and unit profits decrease. The theoretical optimum operating point is where: [ ] At this point my observation is that slight shifts in production capacity bring about greater changes in profitability due to greater grade changes. Therefore, the best financial risk evaluation is obtained by totally revising the mining engineers methods and fixing the financial parameters such as discount and interest rates. A 10% shift in either of these two parameters will not cause near the same variance in economic viability as will a change on the GRADE-TONNAGE curve [(Fig. 2)].

Jan 1, 1980

By D. Perry, G. W. Binkley, G. K. Dumbauld, F. A. Brooks

A new cementing technique has been developed which is particularly applicable to permanent-type well completion operations. The technique makes use of the accelerating effect of calcium chloride on setting time and strength development of cement cake deposited in squeeze cementing. An unique feature is that the accelerator is applied after the unaccelera-ted cement slurry has been squeezed and the excess has been reversed from the well. Laboratory data on the accelerating effect of calcium chloride applied to the fi1ter cakes of three low-water-loss cementing compositions demorzstrate that the procedure results in relatively rapid development of strength and impermeability of the cement cake. Simulated squeeze-ceinenting tests made in the laboratory likewise corroborated the practicality of the procedure. The laboratory tests showed that a newly developed oil-emulsion cemerzting composition is more susceptible to acceleration of set than are modified cements containing high percentages of bentonite. The acceleration procedure has been used successfully in field operations. INTRODUCTION Nature of Problem In squeeze-cementing operations, a substantial amount of time is consumed in waiting on the cement to develop strength after it has been squeezed into the well. Frequently, an interval of 18 to 24 hours or longer is required for the development of strength sufficient to prevent failure of the cement during subsequent operations in the well. Reduction of this waiting-on-cement time offers appreciable savings both in time and in money. A particular type of squeeze-cementing operation to which an increasing amount of attention has been given is encountered in permanent-type well completion operations wherein perforations are to be squeezed off1. In this procedure, it is customary to pump the cement slurry down the tubing and out into the perforated section through a retractable extension pipe. Squeeze pressure is then applied, which forces the cement slurry into the perforations and causes the build up of a compact filter cake of cement within the perforations. The excess slurry remaining in the hole is then removed by reverse circulation. The extension pipe is then retracted, and, if a new interval is to be perforated, a perforating gun is run through the tubing. The newly perforated interval may then be tested by swabbing. In such operations, it has been customary to allow approximately 20 hours or so for hardening of the cement squeezed into the perforations. This time interval is usually measured from the time that the cement is reversed out of the hole to the time that subsequent swabbing is started. If the cement has not developed strength at the commencement of swabbing, the pressure differential caused by swabbing results in failure of the squeeze job. At the time that the work described in this report was initiated, particular consideration was given to the reduction of waiting-on-cement time in squeeze cementing by the permanent-type completion technique. Consequently, much of the experimental work was directed to this specific objective, though the process which was developed for acceleration of strength development has possible application in other than permanent-type completion operations. Method of Attack Although quick-setting cements

Jan 1, 1957

By A. W. Ashbrook

The constraints which are being imposed on metallurgical operations in respect to the environment and worker hygiene are having a substantial influence on the various processes which are being studied and developed for future use. The unit process of solvent extraction can be no exception. It is therefore vital that sufficient be known about the effects of a solvent extraction process in terms of its environmental and hygiene impacts before the process gets to the construct- ion stage. The purpose of this section is to bring these matters to the readers' attention, and to indicate, albeit briefly, some of the problems, and what we know about the effects, of SX processes from an ecological point of view. Hydrocarbons Petroleum hydrocarbons are bio-degraded to form C02; several factors may limit the rate of bio-degradation, which are as follows:

Jan 1, 1978