Search Documents

Jan 1, 1932

Jan 1, 1949

By W. A. Thomas

Steam is, and doubtless always will be, the basic power in the anthracite industry, either directly applied through engines and pumps or electrically. The rapidity with which electric power is being applied to the mining and preparation of anthracite leaves little doubt as to its utility and economy. There is practically no operation, except possibly the drilling of hard rock, that has not been successfully electrified and the matter of drilling is handled economically with electrically driven compressors and the standard compressed-air drills. Conservation and the seemingly ever-increasing cost of production, justify careful consideration of the possible results of the more extensive use of electric power in the industry. It is not planned to discuss, herein, the relative economies of individual applications but to consider the relative economy and flexibility of steam and electric power. The reports available for the year 1920 indicate a production of slightly over 80,000,000 tons of anthracite, of which 8,843,500 tons were used for power and heating purposes; in other words, over 11 per cent. of the production was used at the mines. Some of this was used to generate electric power at the mines, about 160,000,000 kw-hr., while 150,000,000 kw.-hr. was purchased from the public utility companies. One large producer, who is buying some electric power and generating some, used over 13 per cent. of the production for power and heating at the mines. Another producer, where considerable electric power is generated on the properties, is using less than 9 per cent. of the output for power and heating. One of the largest producers has a fuel consumption of over 15 per cent. of the output, besides which considerable power is purchased. A careful study of the field indicates that steam-operated plants use upwards of 13 per cent. of the production for power and heating, while electrically operated plants use about 1 per cent. for heating; so that, for steam-power purposes at least 12 per cent., or 268.8 Ib., are used for power out of each ton produced. In the complete electrification of anthracite mining operations, no set rule can be given for the power requirement, in kilowatt-hours per ton, as conditions vary widely in the matter of pumping, ventilation, and transportation, but the following cases are given as a basis of determining a range and a possible average power requirements:

Jan 1, 1922

By Raymond Mancha

A test of any fan requires the determination of such data as fan pressure, air volume handled by the fan, and power input to the fen shaft. When testing operating mine fans of the centrifugal type, test methods have been employed, for the sake of convenience, that permit great latitude in detail of procedure resulting in wide variance in results by different investigators. Some controversial aspects of field fan testing are the result of past failure to define clearly the various forms of fan pressure and to a lack of understanding of the accurate procedure for the measurement thereof. Also, the anemometer for air-volume measurement, although convenient, if carelessly used and maintained is subject to a wide error range with variation in method of application and in instrument accuracy. The appearance of the axial-flow type of mine fan offers the possibility of refinements in field testing that were impractical with the centrifugal fan. First of all, the fan inlet and outlet are more sharply defined, giving closer agreement as to just where the fan begins and ends; thus there is less disagreement as to the proper location for measurements of fan pressure. The area of passage into the inlet of an axial-flow mine fan usually constricts, causing high air velocities with accompanying steadiness of flow. Thus the fan inlet offers an ideal location for accurate air-volume measurements with the pitot tube, the proper use of which is well established by code. Thereby the controversial aspects of such measurements are eliminated. Use of the Pitot tube also facilitates a more accurate measure of fan pressure, since the individual pressures measured can be properly weighted, as will be explained later. Determination of power input to the axial-flow mine fan operating in the field is subject to the same inaccuracies as with the centrifugal fan if the axial-flow fan is also belt driven. However, because of the higher rates of rotation usual with axial-flow fans, direct-driven units are more numerous and it is unnecessary to assume a drive efficiency, thus eliminating one possible source of error. It is the purpose of this paper to define and explain the various types of pressure measurements involved in a field test of an axial-flow mine fan, and to further explain the proper use of the Pitot tube when measuring pressures and volumes. DefinitioN of Fan Pressures The two fan pressures most commonly discussed are fan total and fan static pressure, each of which has the same meaning regardless of whether the fan is blowing, exhausting, or blowing and exhausting, as in the case of a fan with ducts connected to both outlet and inlet. Fan total presscre is the amount by which the total pressure of the air delivered by the fan exceeds the total pressure of the air received by the fan. This pressure is a measure of the maximum amount of the work done on the air by the fan that is available for external use.

Jan 1, 1942

By Raymond Mancha

A test of any fan requires the determination of such data as fan pressure, air volume handled by the fan, and power input to the fen shaft. When testing operating mine fans of the centrifugal type, test methods have been employed, for the sake of convenience, that permit great latitude in detail of procedure resulting in wide variance in results by different investigators. Some controversial aspects of field fan testing are the result of past failure to define clearly the various forms of fan pressure and to a lack of understanding of the accurate procedure for the measurement thereof. Also, the anemometer for air-volume measurement, although convenient, if carelessly used and maintained is subject to a wide error range with variation in method of application and in instrument accuracy. The appearance of the axial-flow type of mine fan offers the possibility of refinements in field testing that were impractical with the centrifugal fan. First of all, the fan inlet and outlet are more sharply defined, giving closer agreement as to just where the fan begins and ends; thus there is less disagreement as to the proper location for measurements of fan pressure. The area of passage into the inlet of an axial-flow mine fan usually constricts, causing high air velocities with accompanying steadiness of flow. Thus the fan inlet offers an ideal location for accurate air-volume measurements with the pitot tube, the proper use of which is well established by code. Thereby the controversial aspects of such measurements are eliminated. Use of the Pitot tube also facilitates a more accurate measure of fan pressure, since the individual pressures measured can be properly weighted, as will be explained later. Determination of power input to the axial-flow mine fan operating in the field is subject to the same inaccuracies as with the centrifugal fan if the axial-flow fan is also belt driven. However, because of the higher rates of rotation usual with axial-flow fans, direct-driven units are more numerous and it is unnecessary to assume a drive efficiency, thus eliminating one possible source of error. It is the purpose of this paper to define and explain the various types of pressure measurements involved in a field test of an axial-flow mine fan, and to further explain the proper use of the Pitot tube when measuring pressures and volumes. DefinitioN of Fan Pressures The two fan pressures most commonly discussed are fan total and fan static pressure, each of which has the same meaning regardless of whether the fan is blowing, exhausting, or blowing and exhausting, as in the case of a fan with ducts connected to both outlet and inlet. Fan total presscre is the amount by which the total pressure of the air delivered by the fan exceeds the total pressure of the air received by the fan. This pressure is a measure of the maximum amount of the work done on the air by the fan that is available for external use.

Jan 1, 1942

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 ROBERY W HUNT 1883 JAMES C, BAYLES 1884-1885 ROBERT H RICHARDS 1886 THOMAS EGLESTON 1887

Jan 1, 1923

(Read at the Amenia Meeting, October, 1877.) THE Committee on a Standard Gauge have been constantly engaged, since their appointment, in the duties assigned to them.§ They have corresponded with different persons interested in the manufacture and use of gauges in this country, and have received from several of them important information. They have also entered into correspondence with the governments of England, France, Germany, and Russia through their Consuls, and with Austria directly. The Consuls of Germany and France * Transactions, Vol. V, p. 575. t Transactions, Vol. III, p. 43. + Transactions, Vol. II, p. 224. §See Transactions, Vol. V, p.,48.

Jan 1, 1878

By S. Floreen, H. W. Hayden

The effects of additions of iridium, rhodium, ruthenium, and platinum on the mechanical properties of Fe-C alloys were determined. Each alloying element significantly improved the toughness. The results support the general correlation that substitutional alloying elements that stabilize austenite are beneficial to toughness, but the reason for this improvement is not obvious at this time. The effects of substitutional alloying elements on the toughness of steel has long been a subject of both practical and theoretical interest. Despite the obvious importance of this subject, there has been little progress toward understanding the mechanisms by which alloying elements influence the fracture behavior. In some cases the deleterious effects of alloying elements have been shown to be due to mechanisms such as embrit-tlement of prior austenite grain boundaries or inhibition of cross slip in the ferrite lattice. In other cases, however, the reasons for the change in properties are not clear. This is particularly true for elements, such as nickel, that improve the resistance to brittle fracture. Several investigators'-3 have pointed out that there is a correlation between an alloying element's phase diagram with iron and its effect on toughness. Those substitutional alloying elements that stabilize austenite generally are beneficial to toughness, while ferrite-stabilizing elements generally are detrimental to toughness. The word "generally" should be emphasized, because exceptions to this rule can be found. Nevertheless, this correlation does offer a starting point at which to try to understand the effects of alloying elements on toughness. Thus far only two austenite-stabilizing elements, manganese and nickel, have been considered. In order to test the validity of this correlation several other austenite-stabilizing elements were evaluated. The noble metals, iridium, rhodium, ruthenium, and platinum, have binary phase diagrams with iron similar to the Fe-Ni and Fe-Mn diagrams. That is, each element expands the austenite field, and also higher concentrations of each element produce martensitic transformations at low temperatures. Presumably then, each of these elements should improve the toughness of steel. The present study was conducted to determine if this were so. EXPERIMENTAL PROCEDURE The alloys were made as l-lb air-induction melts using electrolytic iron and commercially pure noble metals. Each heat was initially deoxidized by a carbon boil, and further carbon was added to attempt to produce a 0.05 wt pct C content in each alloy. Before pouring, a final refining addition of 0.2 wt pct A1 and 0.1 wt pct Ti was made to each heat. The alloys were cast in a copper mold to produce ingots approximately 1 in. in diam and 5 in. long. The chemical compositions of the alloys tested are given in Table I. The residual nitrogen, aluminum, and titanium contents were all relatively constant at 0.003, 0.03, and 0.02 pct, respectively. The carbon

Jan 1, 1968

By C. G. Fink, G. L. Putnam

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution.

Jan 9, 1950

By Jack D. Arthur

The Surface Mining Control and Reclamation Act of 1977, as amended, and related regulations take blasting safety into consideration by requiring compliance with existing state and federal laws. The regulations are based on blasting practices developed by the industry, as well as research and experimentation by the US Bureau of Mines and explosive manufacturers. Residential areas in the proximity of surface mines have made it mandatory that blasting operations be conducted under restrictions and requirements designed to protect the public and structures located within 0.8 km (0.5 mile) of any surface blasting activities. Restrictions against blasting apply where dwellings, schools, churches, hospitals, or nursing facilities are within 305 m (1000 ft) of blasting operations. They also apply where wells, petroleum or gas storage facilities, municipal water storage facilities, fluid transmission pipelines, gas or oil collection lines, and sewage lines are within 152 in (500 ft) of blasting operations.

Jan 11, 1979

Professor Sir John Cadman, K. C. M. G. (1918) D. Se., F. G. S., M. Inst. C. E., was for two years Technical Adviser' of the Chemical Warfare Department and Liaison Officer between British and French Forces. The Cross of Officer of the Legion of Honor was awarded him in 1917 by the President of the French Republic "in recognition of valuable services rendered by him in the cause of the Allies." At the moment, Sir John is Director of the Petroleum Executive and Chairman of the Inter-Allied Petroleum Conference. In 1915, he was Technical Adviser of the Trench Warfare Supply Department and was awarded C.'M. G. in 1916. J. Edwards-Leckie, C. M. G., D. S. 0., went to Valcartier as second in command of the 72d Regiment, Seaforth Highlanders of Canada, with rank of Major, and later sailed for France as second in command of the unit now known as the, 16th Battalion, the Canadian Scottish. He was promoted to Lieutenat-Colonel on Aug. 14, 1915, and returned to England to take command of the 2d Canadian Reserve Training Brigade at Shornecliffe. On Jan. 2, 1916, he was promoted to Colonel. R. G. Edwards-Leckie, Lieut.-Col. of the 72d Regiment, Seaforth Highlanders of Canada (which unit later became known as the 16th Battalion, The Canadian Scottish, and under that name distinguished itself in France), left Canada for "Over There" on Sept. 14, 1914. He was promoted in France to the rank of Brigadier-General on Aug. 14, 1915, and served until severely wounded in February, 1916. He was Acting Chief of the General Staff, Canadian Overseas Forces in England from September to December, 1916. He returned to Canada in May,

Jan 8, 1918

By M. J. Virnig, G. A. Kordosky, K. D. MacKay

LIX 34 liquid ion exchange reagent, one of a totally new class of metal extractants, is discussed in terms of its properties. Specifically, these properties include improved selectivity for copper and greater recovery. Some comparisons to the well known General Mill's LIX 64N have been made. Particular emphasis is given to treating solutions containing very low copper values and high impurity levels.

Jan 1, 1978

T.B.King (Depaytment of Metallurgy, Massachusetts Institute of Technology)— A valuable contribution of the authors is in the factual information which they have been able to gather; this type of information is quite difficult to obtain. In many respects, however, it would have been better if they had not subsequently embarked on a discussion of the chemistry of the converter process. It seems inconceivable that the authors do not refer to the papers of Schuhmann and his associates14 which have set the thermodynamic foundation for the whole copper smelting operation. In addition, a very useful review on the physical chemistry of copper smelting by Ruddle 5 appeared as long ago as 1953. An examination of this literature would have convinced the authors that there is no cause to be surprised at a correlation between the magnetic content and the silica content of converter slags, though they rightly point out that one should distinguish between the total magnetite content of the slag and the amount of magnetite which may be considered to be in solution. It is not true that the lowest melting converter slag is that corresponding to the eutectic between ferrous oxide and silica. The simplest slag system which can be considered is a three-component system, since both ferric and ferrous iron are present. As Schuhmann, Powell, and Michal have shown, there are lower melting compositions than this eutectic in the ternary system. The most unfortunate impression given by this paper is that the driving force for chemical reaction is determined by the heat of reaction: of course the entropy change must be taken into account. It would have been more correct to list, in Table VI, values for free energies of formation. Nor can it be said that the data in Table VI represent the "best available data." They do not corregtond with any of the recent, acknowledged sources. F. E. Lathe and L. Hodnett(author's reply)— We are pleased that Dr. King finds the factual information in our uawer of some interest. Dr. King suggests that it would have been better if our analysis and discussion of the data had been omitted, largely because our list of references is so. incomplete. If he will carefully read our introduction, he will see that the questionnaire was sent out in the hope of obtaining data which would throw light on certain questions relating to the use of converter refractories. We did not attempt (nor would the AIME have published!) a complete review of the literature on copper converting, as Dr. King has apparently assumed, nor indeed a complete analysis of the data submitted, but tried only to find a sound basis for the choice of refractories, taking into consideration common variations in converter practice. We hope our paper indicates that, by raising the silica content of the converter slag and operating at a higher temperature, the normal circulating load of magnetite can be greatly reduced, and the whole reverberatory-converter operation improved to a major degree, with resultant important savings. Under such operating conditions, chrome-magnesite brick may be expected to stand up better than those of straight magnesite. Regardless of the choice as between these brick types, however, we find the cost of converter refractories to be so low in comparison with other converter costs as to justify operation under the more severe conditions suggested. Valuable as are the papers by Schuhmann and associates and the book by Ruddle, we make no apology for omitting reference to them, nor for using heats of reaction without mention of entropy changes or free energies of formation. Our primary object was to interest the practicing copper metallurgist, with whose language we may claim to be fairly familiar; we think it would have been unwise to include the highly theoretical phases of the subject which Dr. King suggests. The interest shown in our preliminary paper presented at the New York meeting in 1956, and the trends in practice whtat we have observed since that time, suggest that we did not wholly miss the target. In conclusion, we sincerely hope that Professors King and Schuhmann will independently review the data obtained in our questionnaire and submit a paper giving their own recommendations as to the choice of refractories and the particular converter operating conditions which will result in the lowest overall cost of copper smelting and converting.

Jan 1, 1960

IN discussing the art of the goldsmith, it is apparent that it is an art requiring skill. He who wishes to be acclaimed a good master therein must be a good universal master in several arts, for the different kinds of work that come to his hands to be done are infinite. Those who work in gold and silver must outdistance all other craftsmen in learning and achievement to the same degree that their materials outdistance other metals in nobility. Therefore, it is necessary first of all to be a good designer, because design is the key that opens the doors not only to the goldsmith's craft but to all others. Then it is necessary that he understand melting and that he know well how to work with a hammer and how to use flat gravers and burins in engraving, as well as files and chisels. He must also possess certain secrets that are needful to the art, which in truth are parts of alchemy, such as softening gold when it is brittle and raw, coloring it when it has little color, soldering, enameling, working in niello, blanching, gilding, and an infinite number of things which must all be known in detail. But above all he who wishes to do this art well must be very patient in working, must know how to mould and how to proceed with the melt and with the file, hammer, chisel, or other implements for bringing his gold or silver work to the final state which he plans. He must also have good judgment in gems and know well how to recognize every [134v] good or defective quality they possess, and to distinguish the false gem from the true, either when set or when unmounted, as there is need; also how to value them both in buying or selling and in satisfying others who seek his appraisal. He should also be experienced not only in the technique of melting but also in the methods of assaying, parting, refining, cementing, and the like, and still many others. But if I wished to tell you of every part

Jan 1, 1942

By C. L. Magee, H. W. Paxton

The effects of testing temperature, frorn 77" to 420" K, and volume fraction of martensite on the micro-plastic response of unaged Fe-31Ni martensite-austenite aggregates have been determined. The kinetics of the aging phenomena which lead to a decrease in the microplastic response were also characterized. These determinations, supplemented by other experimental results, show that at least two mechanisms of plastic deformation give rise to the apparent softness of the quenched structures. Only one of these mechanisms is fully discussed in this paper The transformation of retained austenite to martensite during the application of stress leads, in specified conditions, to large microplastic strains. This deformation behavior cannot be described by normal transformation plasticity theory but is shown to result from the fact that stress-assisted formation of martensite is a possible deformation mode. The present results and further considerations of previous work lead to the conclusion that it is unnecessary to postulate a special work-hardening mechanism to explain the mechanical properties of unaged martensite. It is now generally accepted that dislocation motion can occur in many solids at stresses very much below the L'macroscpic" yield stress, e.g., 0.1 pct offset. This phenomenon has been investigated by a variety of techniques including measurements of elastic limit,' effective static elastic modulus,~ and irreversible deformation following stressing at low levels.3"5 Of particular interest to the work to be described are exper -iments conducted on the deformation of martensite in attempts to decide whether freshly quenched ferrous martensites are "hard" or "soft".6 Muir, Averbach, and cohenl and McEvily, Ku, and ~ohnston' have shown that as-quenched ferrous rnartensites can be plastically deformed at relatively low stresses. A difference between these two sets of experiments exists in that some diffusion of carbon would take place before testing in the experiments of Muir et a1. because the plain Fe-C alloys which they have tested transform to martensite well above room temperature. McEvily et a1. examined Fe-Ni-C alloys with Ms of about -30"~ and tested the alloys directly after quenching to — 195" ~ —a technique which obviates any appreciable carbon diffusion. Unfortunately, a characteristic of the alloys which transform below room temperature is that they do not transform entirely to martensite. The results discussed below will show that, because the transformation of this retained austenite under stress leads to plastic deformation, one cannot investigate the properties of martensite by such experiments. The existence of a second deformation phenomenon, which is not caused by retained austenite, is also established in the present work. In line with a previous suggestion,' it is believed that the second microdefor-mation mode is principally due to the internal stresses generated by the formation of martensite. To avoid confusion in the present report, the evidence we have found for this interpretation will be discussed separately in a brief note.7 EXPERIMENTAL Materials. The alloys were induction-melted and cast under vacuum; the resulting compositions are given in Table I. The ingots were hot-swaged to 2-in.-diam bar and further cold-swaged and/or cold-rolled prior to specimen preparation. The standard tensile specimens were machined from sheet. The gage section was 0.05 by 0.2 by 5 in.; 0.75-in.-wide ends had 0.2 5-in. centered holes for pinloading. The three-point bend samples were 0.075-in. thick and 0.6 in. bide. The distance between the outer loading points was 5.5 in. In order to establish a standard starting condition, all specimens were quenched to 77°K prior to annealing in vacuo for austenitizing. The temperature of the austenitizing anneal was controlled to + 5"~. The testing and aging temperatures were maintained by various liquid baths (nitrogen, 77"~; freon, 130° to 200°K; acetone, 200 to 300°K; silicone oil, 300' to 450°K) to better than il°K. Strain Measurement. The results herein were derived from both uniaxial tension and three-point bending experiments. For bending tests, the stresses and strains reported are those corresponding to the maximum fiber values. Normally, because of the small strains involved, very sensitive strain measurements are necessary to make microplastic measurements. However, because of the magnitude of the dilatation and shear involved in the martensitic transformation, the requirements in the present experiments proved to be less rigorous. In most experiments the plastic strain was evaluated by measuring stress relaxation and modulus defects. In this method, specimens are loaded rapidly to some predetermined load on an In-

Jan 1, 1969

By H. A. Keller

After an absence of over two years, the writer returned to Leadville in March, 1890. The change which had taken place in the conditions of smelting during so short a time seemed almost incredible. Lead-carbonates had been still further replaced by refractory sulphides, and clean dry ores had been crowded out, to a large extent, by magnesian " fines."

Jan 1, 1893

By George B. Clark

More economical methods of rock disintegration are needed for mining and for rapid excavation. Two major systems are drill and blast and mechanical excavation, including tunnel-boring machines. Current drill and blast methods are cyclic and there- fore limited in speed of operation. Boring machines are limited to moderately hard rock due to bearing and cutter wear. The recent development of ANFO, which has reduced blasting costs markedly, was largely fortuitous because of the method of manufacturing AN prills. New slurries and fluid explosives are easy to load and have high energy-pressure characteristics.

Jan 1, 1971

By E. P. Mathewson

THE experiments described in this paper were made at the Washoe Reduction Works, Anaconda, Mont., for the purpose of determining the relative speed of elimination of the iron, sulphur and arsenic during the process of bessemerizing copper-mattes. The samples were taken from a horizontal "barrel" converter, 8 ft. in diameter and 12 ft. 6 in. long, having an average charge of 9 tons of matte, and blown with a 16-1b. air-pressure. All samples were taken with the blast on, turning the converter from its normal blowing-position to nearly verti¬cal, so that a conical mold, with a long handle attached to a horizontal rod, could be introduced from a platform above the converter into the mouth of the converter and a sample taken. The difficulties of taking a sample with the blast on are appar¬ent, and the irregularities of the lines in Figs. 1, 2 and 3 can be readily accounted for by the amount of slag in the samples. On the whole, the plotting of the results gives comparatively uniform lines, considering the conditions. The samples were taken by the regular sampling-force of the works at 10-min. intervals, as shown in Tables I., II and III, which also give the chemical analysis of the samples so taken. The test shown in Table I. was made with a new converter; that of Table II with a converter that had made three charges and had been cleaned out; that of Table III with a converter that bad blown one charge to white metal, and had then been " washed " out and used for the test. In plotting these results, it was necessary to take, as a basis, the percentage of copper in the samples. This basis does not exactly represent the true condition, since the volume is constantly decreasing and a certain quantity of copper passes into the slag, but it is as near as can be obtained in practice. Take, for instance, in Table I., the sample No. 5, which shows : Cu, 59.9;

Jan 1, 1907

[ ]

Jan 1, 1938

PUGET SOUND SECTION SIMON H. ASH, Chairman, I. F. LAUCKS, Vice Chairman, CHARLES SIMENSTAD, Sec.-Treas., 425 Lyon Building, Seattle, Wash. GLENVILLE A. COLLINS, JOHN N. POTT. The Puget Sound Section met at the Arctic Club, Seattle, Wash., on Jan. 20, 1917. Sixteen members and five guests were present. Dinner having been served, the meeting was called to order. A letter from secretary of Associated Engineering Societies was read, requesting payment of this section's assessment to the quarterly budget, and upon motion it was voted that the Secretary-Treasurer be instructed to pay this assessment. It was moved and carried that this section join with the Chemical Society in a meeting. At the, close of the business meeting, Mr. Asa C. Baldwin gave an illustrated lecture on the "Alaska Boundary Survey." On Feb. 24, the Puget Sound Section again held a meeting at the Arctic Club, 16 members and three guests being present. Chester F. Lee, as member of a committee representing this section in the joint council of the Associated Engineering Societies, reported that by lots it had been decided that the term of service of said committee would be as follows: Chester F. Lee, two years; George. Watkin Evans, one year. Following adjournment of the business meeting, Prof. Joseph Daniels, of the University of Washington, delivered a very interesting lecture on "Milling Practice of The Alaska-Castineau Mining Company." CHAS. SIMENSTAD, Secretary.

Jan 5, 1917