Search Documents

By F. W. Bowdish

Analysis of data on the equilibrium exchange of sodium ions from salt solutions for calcium ions, from various fractions of an oxidized calcareous iron ore from Lorraine, France, strongly suggests that the calcium may be attached to the solid by only one of its bonds. Nearly equal values were found for the equilibrium expression from data covering concentration ranges of 1000 fold for the salt and 235 fold for the ion-exchangeable calcium. Differences indicated between the exchangeable calcium contents of the slime and the sandy portions of the ore, as well as the equilibrium relationship itself, are of importance in the flotation of the ore. During an experimental program on the flotation of oxidized calcareous iron ores from Lorraine, France, ion-exchangeable calcium was found in the ore. Because this source of calcium ions, if not controlled, could thwart all efforts at flotation, an extensive study was made of the phenomenon. The part of that study reported here was to obtain data on the equilibrium established between ore solids and solutions of sodium chloride, and to analyze the data to try to understand better the physical chemistry of the exchange. The ore contains oolites of goethite and quartz grains embedded in a matrix consisting of calcite and a brown cement believed to be the residue from oxidation of the silicate minerals found in fresh unoxidized ore. When ground, a substantial fraction of the ore becomes a fine slime in which is concentrated more than half of the alumina content of the ore. It is believed that the alumina occurs as unidentified clay minerals with which most of the ion-exchange capacity of the ore is associated. A preliminary experiment on the exchange of ions from the ore for sodium ions from solutions of NaCl showed that calcium was about ten times as abundant as magnesium in the exchange solutions. Thus calcium was the predominant ion in causing difficulties with flotation, and it was the only one for which data was obtained in this study. It is believed that the omission of magnesium ion exchange from consideration does not invalidate the results. It is possible, however, that inclusion of magnesium in the analyses and calculations or its prior elimination from the samples would have improved the consistency of the results. EXPERIMENTAL Data about the equilibrium exchange of sodium from solutions for calcium from the solids were obtained using two different samples of material. The solids

Jan 1, 1963

By Harlowe Hardinge

AN extensive recent trip throughout the mining districts of the Southwest, Central West, an Northwest,' reveals a numbes of interesting conditions that have influenced operators, in both large and small mills, to modify their flow sheets insofar as they pertain to crushing and grinding. The changes made and planned for the future should be of interest. It is interesting to note when traveling through the country, how ideas change and practice is modified, and it is rather amusing to see how milling methods seem to run, more or less, in cycles. New ideas and developments are brought about which run through the industry and are taken up by many of the best and most well informed operators. Some of them will change, sooner or later, back to their old practice; for, like everything .else, what will work well in one place will not necessarily be suited to another. On the other hand, it is often difficult to establish. other practices known to be of value, owing to the natural resistance to make a change, but on the whole, the western mill men seem to be more alive to possible benefits of various modifications than any other engineers with whom I have come in contact in all parts of the world. Mill men in other parts of the world always keep in con- tact with what is being done in the western part of the United States, but it does not necessarily follow that those in the western part of the United States are always right. Some of these changes that have been made and afterward abandoned will be referred to later.

Jan 1, 1929

By Fred D. Gustafson

With the postwar emergency for new housing and for new industrial buildings, much research has been done on lightweight aggregates for use in concrete and plaster. The trend toward lighter weight aggregates to relieve the dead load on the higher, steel frame- work buildings started toward the end of the last century. Progressively the requirements be- came more stringent, crushed bank slag, weighing 80 lb per cu ft as com- pared to 100 lb for crushed rock, was supplemented in some sections by foamed slags and expanded shales weighing from 40 to 60 lb per cu ft. In other sections cinders were used weighing from 40 to 50 lb, including sand. Sections favored with more recent vulcanism turned to pumice weighing from 30 to 60 lb, whereas other localities made use of diatomite, from 28 to 40 lb. Exfoliated vermiculite weighing from only 6 to 10 lb per cu ft came into use. As the search for lighter weights in aggregates continued so did the search for other desirable properties such as nailability, ease of cutting or channeling, and good insulation to both sound and heat. This search eventually led to a widespread interest in the expansion of perlite, or similar volcanic glasses, with the result that in 1946, the Office of the Housing Expediter' listed eleven firms reporting the operation of processing plants either on pilot or commercial scale producing aggregates weighing from 2 to 16 lb per cu ft.

Jan 1, 1949

By R. E. Allen

THERE was once a time when a practical oil man would appraise or buy a producing property on the basis of from $200 to $500 per barrel of average daily settled production. Curtailment-has, for the present at least, caused a virtual abandonment of the "barrel -of settled production" as a yardstick of, oil property value and in its place has come the "barrel of allowable production," which, although an artificial thing, is nevertheless now the principal factor governing the rate of ?pay out? or investment return. The potential production of a well, settled or otherwise, is of less importance in determining the present worth of a well than is the rate at which it may be produced. Speaking only of true potential for the moment, it is obvious that of two similar wells having the same potential, the one having the highest rate of allowable production would be worth proportionately more than the one of lesser allowable. The discount factor for deferred return and risk can easily vary the present values of the two wells by as much as 20 per cent when allowable rates are not greatly different.

Jan 1, 1934

By AIME

IN the parlance of Hollywood, it was a super-colossal meeting. In the more restrained language of engineers, the Institute's 75th Anniversary Celebration attracted the largest crowd ever; was the longest Annual Meeting ever held, occupying a full week; had more important papers, more important people, more of an international flavor, and more glamour than ever before. And in the minds of those who came to the big city from the wide open spaces, one other record should be mentioned: for those not on an expense account, it was the most expensive affair ever staged by the Institute! To state the attendance down to the last digit for a meeting such as this is impossible. The total names registered on cards, plus those who attended the Annual Banquet but were not otherwise registered, came to 3149. But a few were registered twice, and probably a still larger few did not register at all, but just dropped in for a session or two in which they were interested. It would appear that 3200 would be about as close an estimate of attendance as could be made, and that is some 300 more than came to the biggest Annual Meeting of the past-in 1944. A considerable number of members brought their wives, but most were delegates at large.

Jan 1, 1947

By A. E. Bibb, F. W. Kunz

A platelet form of zirconium hydride was found in zirconium and ZY-1 wt pct U single crystals containing hydvogen in the range of 50 to 100 ppm. The habit planes for the hydride plateletg in the zirconium crystals were found to be {1012}, {1121}, and (1122) while the habit planes in the ZY-1 wt pct U crystals were {1121), {1123}, and (1.231). With the exception of the {1231} plane, these have been identified as the twin planes in zirconium. The different effect of hydridc on the mechanical puoperlies of zirconium at high and low strain rates has been explained in terms of the defornzation mechanism and the habit planes of the hydride. ZIRCONIUM and zirconium-base alloys are considered for many nuclear reactor applications, where the pick-up of hydrogen is a distinct possibility, if not an unavoidable occurrence. An excellent example of this is the absorption of hydrogen by zirconium and its alloys during aqueous corrosion, where as much as 30 pct of the hydrogen produced by the corrosion reaction is picked up by the metal. Under the proper conditions, the absorbed hydrogen would precipitate as zirconium hydride and consequently alter the mechanical and physical properties of the zirconium-base alloys. The knowledge obtained from a study of the crystallographic aspects of the hydride precipitation is necessary for the interpretation of the observed changes in the mechanical and physical properties. The deleterious effect of hydrogen on zirconium-base materials is not always observed in normal slow tensile loadings at or above room temperature, but becomes immediately obvious under impact loading, where the energy absorbed decreases with increasing hydrogen content,' and in notched specimens where triaxial loadings are attained.2 This effect is of serious consequence in the applications of Zr where shock loads or high strain rates are experienced. The purpose of this investigation was to determine the crystallographic planes of the Zr and Zr-1 wt pct U matrices upon which zirconium hydride will precipitate and to correlate these with the observed mechanical property data. PROCEDURE Crystal Growth—Single crystals of Zr and Zr-1 wt pct U alloy were used in this investigation. The Zr crystals were made from sponge that had a typical analysis as shown in Table I. Large grains were grown in this material by rapid cooling an arc-melted charge in a button furnace. This operation undoubtedly lowered the volatile impurity concentration below those listed in Table I. Back-reflection Laue patterns of these large grains showed the presence of considerable substructure and lattice distortion within each grain. It was found that an 18-day anneal in an argon atmosphere at 840°C (a high a heat-treatment) followed by furnace cooling, resulted in the further growth of the large grains and removed the detectable substructure ana lattice distortion. Equiaxed crystals with a cube edge of approximately 1/4 in. were produced in this manner. Large crystals of Zircaloy-2 (1.5 wt pct Sn, 0.15 wt pct Fe, 0.1 wt pct Cr, 0.05 wt pct Ni) also were produced by this technique but the large amount of substructure formed could not be removed by annealing. The Zr-1 wt pct U solid solution crystals were produced from an alloy rod consisting of Westing-house-Foote hafnium-free crystal bar zirconium and depleted uranium. The chemical analysis of the alloy is also given in Table I. Three-inch sections were cut from an 0.120-in.-diameter alloy rod and tapered to a fine point on each end. The samples were sealed in evacuated Vycor tubes, homogenized for 5 hr at 1000°C in the ß-phase field, and slowly lowered in a gradient furnace into the a phase (800°C), annealed for 60 hr at this temperature to produce grain growth and furnace cooled. This technique produced large grains approximately 1/2 to 3/4 in. long over the entire cross section of the rod, which were free of observable substructure. Metallographic examination up to X1000 did not show the existence of any second phase in these grains. Crystal Orientation—All crystals were abraded on fine emery paper to produce two flat surfaces 90 deg to each other. The crystals were analyzed by the standard Back-Reflection Laue technique to obtain the crystal orientation with respect to the abraded surfaces. The Back-Reflection Laue Photograms of all crystals used were clear and sharp indicating that the crystals were free from any substructure that could be detected by these means. Hydriding—Only samples containing four to five grains were used for hydriding. Samples that exhibited fine grained patches were discarded. The samples were hydrided using the following technique. After etching in 48 vol. pct HNO3, 48 vol. pct H2O, and 4 vol. pct HF (48 pct) solution, the specimens

Jan 1, 1961

By F. Ernest Brackett

Much new data on the flow of gases have been discovered by recent experiments by the United States Bureau of Mines and others. Although additional investigation is still desirable, the information now collected seems sufficient to attempt a tentative coördination of the friction factors. This study is confined entirely to fluid friction when the density throughout the duct is so nearly constant that it may be so considered. In the subsequent discussion the following notation is used: v = mean velocity of fluid in duct, feet per second. v' = mean velocity of fluid in duct, meters per second. R = hydraulic radius of duct, feet. R' = hydraulic radius of duct, meters. S = the hydraulic slope. P = pressure absorbed by friction, pounds per square foot. p = pressure absorbed by friction, pounds per square inch. p' = pressure absorbed by friction, kilograms per square centimeter. A = sectional area of duct, square feet. O = perimeter of duct, feet. L = total length of duct, feet. L' = total length of duct, meters. d = diameter of a cylindrical duct, inches. w = density of the fluid, pounda per cubic foot. g = specific gravity of the fluid compared with water = w % 62.4. C, k and B, coefficients for formulas using English measures. C' = metric coefficient, v' = C'R'S. n = coefficient of roughness for English or metric units. The basic formula for the flow of all fluids at constant density appears in the three following forms, which may be denominated: (a) The slope formula, v = CRS (b) The ventilation formula, " n = (c) The pipe formula, C is Kutter's coefficient, which is extensively applied to the flow of water in ducts and channels of all kinds; E is Atkinson's coefficient, used principally with air in ventilation problems; B is a coefficient conveniently adapted to studying the flow of water, gases and vapors in pipes. 312

Jan 1, 1927

PRESIDENT Mrs Oliver Bowles 5000 Massachusetts Avenue N W. Washington 16, D C FIRST VICE-PRESIDENT RECORDING SECRETARY Mrs David E" Park Mrs Thomas T Read 115 East 67th Street 9 Windmill Lane New York 22, N Y Scarsdale, N Y

Jan 1, 1951

By G. R. St. Pierre, A. J. Wilhelem

In connection with the reduction of hematite or magnetite to metallic iron, it appeared desirable to study the rate of reduction of each oxide to the next lower oxide under conditions which excluded all other condensed phases. For this purpose, pellets of Fe,O,, Fe,O,, and oFeOo were prepared. A gas train for the preparation of Ar-Hz-H20 mixtures was employed to establish a continuous flow of a controlled atmosphere over a pellet suspended on a balance. In this manner the following individual reduction steps could be studied: For example, pellets of hematite were reduced solely to magnetite by adjusting the gas atmosphere such that it was oxidizing to wustite. In other words, the reaction was complete when the hematite pellet had been totally converted to magnetite. The pellets were prepared from Baker Chemical ferric oxide. The ferric oxide powder was moistened and handrolled. Air sintering at 950°C produced Fe,0, pellets with a density of 3.65 g per cm3. The pellets ranged in size from 0.6 to 1.2 cm diam. The magnetite and

Jan 1, 1962

By Frank L. Gaddy

Falls of roof account for over 50% of the fatalities that occur in coal mines in the U.S. Thus, roof control is one of the more important phases of underground mining. In reality, the control of roof influences the system of mining and is a major determinant of the width and spacing of working places, operations at the mining face, ventilation control, and surface subsidence. Frequently, the control of roof is the largest single cost item. Roof control is a never-ending task, not only at the working face and throughout sections where men are working, but along haulways and airways that must be maintained for the life of the mine. This is because roof, even the best of roof, slowly deteriorates, so it must be frequently examined, with corrective support applied when needed. As coal is excavated, stresses are set up in the roof became the previous equilibrium is upset, resulting in pressures that cause fractures and slight, movements that are, frequently, hard to detect. Unless the immediate roof, in the excavated area, is given support by artificial means, it might fall or there might be a succession of falls, varying from a thin scale to several feet, depending on the nature of the top. Exceptions to this are those rare mines, or sections of mines, with hard, strong, nonweathering roof that requires no support. GENERAL CLASSIFICATION OF ROOF There are two broad types of roof as far as support is concerned, the immediate roof above the coal and the main roof. Artificial support for mining purposes is only concerned with the immediate roof as nothing except large blocks of solid coal, or massive concrete, will support the main roof. The immediate roof is generally a few feet thick but can vary from inches to 20 ft or more. There are examples of where there is no immediate roof as the massive main roof lies directly on the coal bed, but this is rare. Impossibility of supporting the main roof and all of the cover

Jan 1, 1973

By T. H. Aldrich

(San Francisco Meeting, October, 1911.) THERE are two conditions generally prevailing upon the earth-those within atmospheric influence, tending towards oxidation, and those away from atmospheric influence, tending towards reduction. Practically all mineral substances from mines of any depth are in a reducing condition. Since the cyanide process, in order to dissolve silver or gold, requires that the prevailing conditions under which it operates shall be oxidizing, and the materials usually acted upon being of a reducing character, it becomes necessary to supply oxygen to the solution carrying the cyanide. This oxygen is usually supplied through the medium of dissolved air in the solution, or through the medium of various chemical compounds, which upon combining with the solution or the ore give off a part of their oxygen. Strange as it may seem, practically all mineral substances are partly soluble in water, especially water carrying alkali or cyanide. The greater the surface exposed and the finer the material is ground, the greater will be the rate of dissolving of the reducing agents from the ore into the cyanide solution. In most cases, if the solution carrying the ore particles is agitated with air, the air will dissolve into the solution faster than will the reducing-agents; but in some cases the reducing-agents will dissolve more rapidly on account of easy solubility or greater surface exposed. It is a dissolving race between the oxygen from the air and the reducing-agents from the ore, and if the reducing-agents predominate, cyanide will not dissolve the gold from the ore. In many cases it will dissolve some of the gold, because in a mass of irregular shape some of the gold particles might be exposed upon the outside surface of a particle of rock;' but if the solution had to penetrate through cracks, the side-walls of which were lined with reducing-agent-

Feb 1, 1912

By C. A. Heiland

The new geophone described herein was developed by Charles H. Hull, instrumentmaker of the Colorado School of Mines, and the writer. The first geophone was invented during the war for the purpose of detecting enemy sapping or underground mining operations and for locating enemy artillery. It is based on the principle of the seismograph—a heavy lead mass suspended by one or two diaphragms, which are clamped to an air-tight case. When the ground vibrates during the transmission of sound waves, the case moves with it while the so-called steady mass remains practically motionless. Attached to the top of the casing is a hose leading to an earpiece shaped like a stethoscope. When the mass and the diaphragm move up and down in the case, the air is compressed and rarified in the inside; thus the vibration is communicated as sound wave to the human ear. The geophone combines a surprising simplicity of construction with an extreme sensitivity. Other listening instruments were developed during the war, adaptations of the telephone and the microphone—that is, instruments operating through the medium of electricity—of which the so-called seismicrophone, an adaptation of the carbon-granule microphone receiver, probably has found the greatest application, but such instruments apparently have not proved as useful as the simple geophone despite obvious advantages arising from the use of electricity. The carbon receivers were more subject to extraneous noises and to what is called "frying," and they did not offer the advantage possessed by the geophone; namely, the simultaneous use of two receivers, which makes it possible to determine the location of the source of sound. During the war, the U. S. Bureau of Mines made a study of the geophone and of the propagation of sound waves through rock. These studies have been continued, as the earlier results proved the possibility of using the geophone in various non-military ways, principally in mining, and the results of these studies have been published.'

Jan 1, 1932

By Frank L. Antisell

Certain physical and chemical properties of copper are so intimately related that a change in variation of the physical properties indicates a certain chemical change. The standard specifications of copper of the American Society for Testing Materials are based upon physical characteristics with one exception, namely, the copper contents. The physical standard includes electrical properties, defects in the "set or casting," variation in dimensions, weight, etc. Paragraph 4 of the specifications states, " Wire bars, cakes, slabs and billets shall be substantially free from shrink holes, cold sets, pits, sloppy edges, concave tops, and similar defects in set or casting." Shrink holes and concave tops indicate both physical and metallurgical defects; cold sets, sloppy edges, etc., indicate physical defects only; small pit holes may be indicative of either or both physical and metallurgical defects, depending on conditions under which they originated. To the refiner, a copper casting, no matter how made, is known as a "shape," irrespective of whether it is wire bar, ingot, cake, slab, billet, etc. As practically all shapes are cast in an open mold, that is a mold without cope, the surface of the shape cools in contact with the atmosphere and has a coating of oxide. Certain phenomena of the surface indicate the adaptability of the metal for forging or rolling. The writer believes that it is much simpler to produce shapes that are metallurgically correct than those that are mechanically satisfactory. When copper is to be rolled into thin sheets or drawn into very fine wire, the slightest physical defect becomes evident. It is, therefore, of the utmost importance to consider every characteristic of the shape and ascertain the physical and chemical relationship. Pitch and Set.—The appearance of the surface of the copper when cooled is considered as to its "pitch," or the general contour of the surface of the shape (which may vary from a concave to a convex); and the '" set,"' or the detail appearance of the surface of the shape (the wave-like structure). When the shape presents a concave surface, it is known as "low pitch;" a convex surface is known as "high pitch" or "tough pitch;" and a level surface is called "flat pitch." The set of the copper is, in a very large measure, directly related to the pitch; and so intimately are

Jan 1, 1921

By R. McDonald, B. C. Maine

CERRO'S power system consists of three main hydroelectric plants and one steam-electric plant. These are located on the eastern slope of the main Andes range at altitudes between 12,000 and 13,000 ft. The hydroelectric group utilizes the watershed which extends for about 150 kilometers south from Cerro de Pasco, divided into two catchment areas which lie adjacent. The northern area serve,, the medium-head plant of Mal¬paso. while the southern area provides for the high-head plants at Pachachaca and Oroya. The rainfall, as registered at the rain gauging stations of the three hydroelectric plants, averages 33 in. per year; all these stations are subject to the same hydrological conditions, and the bulk of precipitation occurs between October and March. Rainfall during the dry season, April till September, has no appreciable effect on the total annual runoff. Table 1 shows the storage capacities of the main reservoirs of the hydroelectric group. The four plants are tied together electrically by a 50-kv. transmission network, the system being 3-phase 3-wire at 60 cycles with a solidly grounded

Jan 1, 1945

By H. L. Teichman, E. M. Sipprelle

ENACTMENT' of Public Law 290 by the 78th Congress authorized the U. S. Department of the Interior, Bureau of Mines, to conduct an experimental program to develop the technology for obtaining oil from oil shale. In adopting and later extending this legislation, the Congress recognized the impending necessity of supplementing ground petroleum reserves with synthetic fuels. Under the provisions of this legislation, the Bureau of Mines, among other things, was charged with the responsibility of developing mining techniques, methods, and equipment for mining the oil shales of the Green River formation of Colorado, Utah, and Wyoming. The oil shales of western Colorado are apparently richer, more accessible, and more amenable to exploitation than elsewhere in the Rocky Mountain region. The site chosen for the Bureau's Experimental mine is about 10 miles west of Rifle in northwestern Colorado. It is within a 1000-sq-mile area from which, it has been estimated, 300 billion barrels of shale oil could be produced from a 500-ft measure near the top of the formation. One hundred billion barrels of this amount could be produced from the Mahogany ledge, a 60 to 100-ft section near the bottom of the 500-ft measure. This ledge is considered to have economic importance at present. The Green River formation was laid down as sediment in the bottom of vast, shallow inland lakes during Eocene time. The deposit is flat-lying, and there are no faults, fissures, or local rolls. Oil shale is actually a strong, tough magnesium marlstone, which will stand unsupported over relatively wide spans. These and other natural physical characteristics favor mechanized, low-cost mining, which is essential for establishment of an oil-shale industry. It was realized from the outset that an extensive research program would be necessary to develop mining methods, equipment, and techniques for a mechanized, low-cost operation. The program was designed to include research. into all the productive phases of mining, such as drilling, blasting, loading, transportation, and maintenance of the mine structure. The methods, equipment, and techniques developed as a result of this research have established a production of 116 tons per man-shift total labor at a direct cost of $0,292 per ton. Another important phase of the research program that has received little publicity because of its theoretical nature is study of the roofstone behavior and determination of mine structure stresses. This paper purposes to discuss this phase of the research program. Preliminary studies of the physical properties of the Green River oil-shale formation were made in the Barodyramics Laboratory at Columbia University during the latter part of 1945 and the early part of 1946.* The purpose of these studies was to determine the maximum size of unsupported underground openings that would be commensurate with safety and still permit the use of large, efficient mining equipment. Also to be determined were the pillar support to extraction ratio and the shape, size, and spacing of supporting pillars. Selected samples of possible roofstones near the top of the Mahogany ledge, as well as representative samples of different rock types found within the ledge, were obtained from the Bureau's oil-shale mine for these studies. The maximum safe unsupported roof span calculated from this work was 200 ft. Using a safety factor of four, it was theoretically determined that openings 60 ft wide could be advanced under a roofstone at the top of the Mahogany ledge. To support the overburden, 60-ft-sq pillars would be left in a checkerboard pattern. From visual observations made of core samples through the selected roofstone at the oil-shale mine, it was determined that the roofstone was actually a plate 6 to 8 ft thick. Because the calculations were theoretical and allowance had to be made for unknown cracks and fractures in the formation, openings 50 ft wide and pillars 60 ft sq were originally contemplated in the Bureau's Experimental mine. This would be the minimum allowable width that would permit use of large underground mining equipment. For lower mining costs and greater efficiency larger openings were desirable. Different but analogous approaches were made to the problem at the Bureau of Mines Applied Physics

Jan 1, 1951

By H. L. Teichman, E. M. Sipprelle

ENACTMENT' of Public Law 290 by the 78th Congress authorized the U. S. Department of the Interior, Bureau of Mines, to conduct an experimental program to develop the technology for obtaining oil from oil shale. In adopting and later extending this legislation, the Congress recognized the impending necessity of supplementing ground petroleum reserves with synthetic fuels. Under the provisions of this legislation, the Bureau of Mines, among other things, was charged with the responsibility of developing mining techniques, methods, and equipment for mining the oil shales of the Green River formation of Colorado, Utah, and Wyoming. The oil shales of western Colorado are apparently richer, more accessible, and more amenable to exploitation than elsewhere in the Rocky Mountain region. The site chosen for the Bureau's Experimental mine is about 10 miles west of Rifle in northwestern Colorado. It is within a 1000-sq-mile area from which, it has been estimated, 300 billion barrels of shale oil could be produced from a 500-ft measure near the top of the formation. One hundred billion barrels of this amount could be produced from the Mahogany ledge, a 60 to 100-ft section near the bottom of the 500-ft measure. This ledge is considered to have economic importance at present. The Green River formation was laid down as sediment in the bottom of vast, shallow inland lakes during Eocene time. The deposit is flat-lying, and there are no faults, fissures, or local rolls. Oil shale is actually a strong, tough magnesium marlstone, which will stand unsupported over relatively wide spans. These and other natural physical characteristics favor mechanized, low-cost mining, which is essential for establishment of an oil-shale industry. It was realized from the outset that an extensive research program would be necessary to develop mining methods, equipment, and techniques for a mechanized, low-cost operation. The program was designed to include research. into all the productive phases of mining, such as drilling, blasting, loading, transportation, and maintenance of the mine structure. The methods, equipment, and techniques developed as a result of this research have established a production of 116 tons per man-shift total labor at a direct cost of $0,292 per ton. Another important phase of the research program that has received little publicity because of its theoretical nature is study of the roofstone behavior and determination of mine structure stresses. This paper purposes to discuss this phase of the research program. Preliminary studies of the physical properties of the Green River oil-shale formation were made in the Barodyramics Laboratory at Columbia University during the latter part of 1945 and the early part of 1946.* The purpose of these studies was to determine the maximum size of unsupported underground openings that would be commensurate with safety and still permit the use of large, efficient mining equipment. Also to be determined were the pillar support to extraction ratio and the shape, size, and spacing of supporting pillars. Selected samples of possible roofstones near the top of the Mahogany ledge, as well as representative samples of different rock types found within the ledge, were obtained from the Bureau's oil-shale mine for these studies. The maximum safe unsupported roof span calculated from this work was 200 ft. Using a safety factor of four, it was theoretically determined that openings 60 ft wide could be advanced under a roofstone at the top of the Mahogany ledge. To support the overburden, 60-ft-sq pillars would be left in a checkerboard pattern. From visual observations made of core samples through the selected roofstone at the oil-shale mine, it was determined that the roofstone was actually a plate 6 to 8 ft thick. Because the calculations were theoretical and allowance had to be made for unknown cracks and fractures in the formation, openings 50 ft wide and pillars 60 ft sq were originally contemplated in the Bureau's Experimental mine. This would be the minimum allowable width that would permit use of large underground mining equipment. For lower mining costs and greater efficiency larger openings were desirable. Different but analogous approaches were made to the problem at the Bureau of Mines Applied Physics

Jan 1, 1951

By J. M. Weehuizen

Complete details are given of the drilling method by which two shafts were sunk at the new Beatm'x mine of Staatsmijnen in the Netherlands. The nature of the rock strata in the Dutch mining district determined choice of the drilling rather than the freezing method. Data for each step and details of the equipment used are given in the illustrations. Staatsmijnen was founded in 1902 with government financial backing, but it is run as a private enterprise, on a commercial basis, with the normal fiscal obligations. The company now has four mines in operation with annual outputs amounting to 7 1/2 million tons of coal. In 1952 it was determined that a new mine—the Beatrix—would be opened. Details of the shaft-sinking operation are described in this paper. SHAFT LOCATION The coal-bearing carboniferous rock in the Dutch mining district is overlain almost completely by soft water-bearing strata, which at the site of the new shafts are about 1600 ft thick. The sinking of the new shafts through this soft water-bearing overburden (Fig. 1) is a costly and time-consuming affair. From the two availaible sinking methods: 1) Poetsch's well known freezing method or 2) the drilling method of Honigmann-de Vooys, the latter was preferred, not only because of its relative cheapness, under the prevailing conditions, but primarily because by using the drilling process, a special type of shaft lining of steel, concrete, and bitumen could be used. The new shafts, located 330 ft apart, have an inner diameter of 18 ft, 4 1/2 in. The boreholes, which have a diameter of 25 ft and which were drilled through nearly 1600 ft of overburden and some 100 ft of carboniferous, each contain more than 29,000 cu yd—by far the largest in the world. DRILLING METHOD The drilling method is based on the use of mud-flush—a thin mixture of clay and water—to keep the borehole filled during the entire drilling period and during insertion of the lining (Fig. 2). The pressure of the mudflush against the borehole wall is greater than that of the water in the surrounding

Jan 1, 1961

By AIME AIME

Council.* PRESIDENT OF THE COUNCIL. ROBERT W. HUNT CHICAGO, ILL. (Term expires February, 1907.) VICE-PRESIDENTS OF THE COUNCIL. WILLIAM P. BLAKE TUCSON, ARIZ. THOMAS F. COLE DULUTH, MINN. IRVING A. STEARNS WILKES-BARRE, PA. (Term expires February, 1907.) HENRY AL HOWE NEW YORK, N. Y. J. B. GRANT DENVER, COLO. JAMES D. HAGUE NEW YORK, N. Y. (Term expires February, 1909.)

Jan 1, 1907

By A. S. Odeh

During the last few years, several authors1-6 have advanced mathematical solutions, both exact and approximate, to the pressure behavior of a well producing from a region bounded by a circular discontinuity. The most recent solutions were reported by Carter, and by Bixel and van Poollen. Varter solved the appropriate equations analytically. Bixel and van Poollen reported a numerical solution and provided correlation charts for the interpretation of flow tests; their method uses an overlay technique and is valid for wide ranges of mobility and storage capacity ratios. The mobility ratio is defined as the ratio between k/p of the two zones, and the capacity ratio is defined as the ratio between $c of the two zones. We have developed independently an analytic solution, programmed for the CDC 1604, that agreed with Carter's.'1 The same differential equation, assumptions, boundary, and initial conditions were used. We ran 30 drawdowns and 30 buildups of a unit capacity ratio and of varied mobility ratios. We also varied the radial distances to the discontinuity, and the radii of drainage. We examined the results and obtained correlations that were simple to apply and useful in flow test interpretation. The results and the correlations reported here in graphical form allow the determination of the mobility of the two zones and the radial distance to the discontinuity. They eliminate the need to fit field data to a curve as is required in the overlay technique.6 Thus, the advantages of the present correlations are that they require less effort and they provide a unique answer. They also provide guidelines for selecting the parts of the flow test plot to be used in the interpretations. Moreover, the results obtained from the programmed analytic solution define the time intervals where the approximate solution reported by Hurstl and discussed by Larkin2 are applicable. Normal buildup and drawdown plots resulted in an early straight line, a long transition zone and a late (second) straight line. However, the second straight line will not occur if the drainage radius is not at least 10 times the radial distance to the discontinuity. The mobility of the imer and outer zones can be calculated from the slopes of the first and second straight lines, respectively, by the normal methods of the flow test analysis. We found that the radial distance to the discontinuity may be determined from the abscissa value for the point of intersection of the extensions of the two straight lines. Results similar to some of these were reported by Adams et aL7 The approximate solution compared favorably with the exact one during the first and second straight-line periods. However, during the transition zone, deviation occurred between the two solutions. Discussion of Figures Figs. 1 through 7 summarize the results of this investigation. On Figs. 3 through 7 there appears the equation of each respective plot. In this paper the mobility ratio M is defined as klp2/kzpl, where subscripts 1 and 2 refer respectively to the inner and outer zones, and dimensionless time = t, = 6.32 X In the investigation, M ranged from 0.25 to 50;

Jan 1, 1970

By E. Northcott, F. N. Oberg

By electrostatic separation, course Florida pebble phosphate, too lou-grade to find a ready market, can be upgraded to a satisfactory saleable product. Pebble running from 60 pct bone phosphate of time may be upgraded to 73 to 77 pct BPL depending on the mineralogical. structure of the pebble and the nature of the silica innpurity. High-grade concentrates from Florida pebble phosphate deposits have long been recovered by wet methods. When work was begun in the field, only the coarse pebble (generally +1 mm) was re- covered. In the 1920's a froth flotation process was developed to separate quartz from the finer phosphate fractions, but this method proved unsatisfactory for treating the intermediate fraction (—1 mm +35 mesh). Consequently various other processes were adapted, including agglomerate tabling and spiral separation of reagentized feed. Today the three processes are used—washing and screening for coarse pebble, tabling or spiraling for intermediate sizes, and flotation for —35 mesh material.

Jan 1, 1959