Search Documents

By Frank R. Milliken, Robert Goodwin

In September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 60 per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. I, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of which ranged from 62 to 74 per cent recovery. On the basis of these, a 200-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1943

By Robert Goodwin, Frank R. Milliken

In September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 60 per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. I, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of which ranged from 62 to 74 per cent recovery. On the basis of these, a 200-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1943

By W. Arthur White

Underclay squeeze is the plastic flowing of underclay below coal pillars into mined-out entries and rooms. Squeezes may be caused either by wet mine conditions where the moisture is taken up by the clay-making it more plastic-or by the presence of certain clay minerals, such as mont-morillonite, which are plastic when there is enough natural moisture. Under either condition, sufficient stress will cause the underclay to flow. Squeezes may fill an entry or room within several hours, or it may be several months before movement stops. Squeeze areas commonly cover hundreds or thousands of square yards.

Oct 1, 1956

By S. H. Ward, R. A. Barker

THE Juniper Prospect is in Carleton County, N. B., at approximately 46º 31' north latitude, 67º 20' west longitude. During the summer of 1955 an area in west-central New Brunswick was selected for aerial electromagnetic prospecting with American Metal Co.'s helicopter-mounted equipment. Generalized, small-scale government geologic maps had suggested that this area was located along the western border of the northeast-trending granitic backbone of northwestern New Brunswick and might be underlain by the Ordovician-Silurian sediments and volcanics that are the host rocks for the recently discovered sulfide deposits of the Bathurst-Newcastle district.

Jan 1, 1958

By S. H. Ash

lowest fatal injury rate in history conferences stress selling worker on safety international safety conference beneficial

Jan 2, 1951

By William C. Maurer

A survey of 25 novel drills has shown that spark drills have potential for drilling oil wells and blastholes at higher rates than rotary drills. Available laboratory and field data were extrapolated to drilling rates of 70 to 280 fph for full-scale spark drills. Most of the data used in these extrapolations were from small-scale laboratory tests at atmospheric pressure. Accurate extrapolation of the small-scale spark drill tests to full-scale field drills was complicated by the fact that the effect of fluid pressure in the well bore and the effect of spark size were not known. In order to answer these questions and to more accurately evaluate the potential of spark drills for drilling blastholes and oil wells economically, a high-voltage spark discharge system was assembled. This equipment produced powerful sparks (10,000 joules) equivalent to those that would be used on a 100-kw full-scale field drill. These sparks are 100 times more powerful than those previously used on spark drills, thus eliminating extrapolation of the spark size. In addition, a pressure chamber was modified to enable using these sparks to produce craters in rocks at fluid pressures up to 15,000 psi, thus eliminating extrapolation from atmospheric pressure to the high pressure existing in deep oil wells. These tests have provided considerable information for more accurately evaluating spark drills for oil-field drilling. MECHANISM AND THEORY OF SPARK DRILLING Spark-Drilling Mechanism When a high-voltage capacitor is discharged across two electrodes, the dissipated energy produces a high-temperature, high-pressure plasma for a few µsec. When these sparks are discharged in air, they undergo considerable expansion (Fig. 1) and produce low-pressure pulses (103-

Jan 1, 1970

By M. F. Comerford

M. F. Comerford (Smithsonian Astrophysical Observatovy)- The authors' concern about the effects of preferred orientation is justified and emphasizes a phenomenon that can be a source of serious error, but the cogency of their concluding statement bears close examination. They contend that comparison of intensities from parallel planes of the two phases, as proposed by Averbach, Comerford, and Bever,13 leads to incorrect results. The state- ment is based on the fact that, in Fig. 3, intensity measurements at extreme angles of tilt, (2, lead to different values than those given by the average of all the data. The proposed explanation is that unsuspected superpositions of (110), reflections spuriously enhance the martensite intensity. However, it can be shown on appropriate stereographic projections that no superpositions occur which can affect the reflections in question. Hence, the ex-

Jan 1, 1965

By William P. Dyrenforth

The principle of electrostatic separation is discussed and elaborated on by dividing into the three main mechanisms of electrification as applied to separation of solid substances, i.e., (1) contact electrification, (2) electrification by conductive induction, (3) electrification by ion bombardment. Types of equipment used for electrostatic processing are described and the effects of humidity mentioned. Processing of iron ore, titanium minerals, rare earths and cassiterite is discussed and some existing plants are described.

Jan 1, 1978

By John Pew

PRIOR to the development of the bulk-oil carrier, practically all transportation of oil was in barrels and in cans contained in wooden cases; the latter was known as case oil. In the year 1885, approximately two hundred million gallons of petroleum were exported from this country in barrels and about one and three-quarter millions in bulk; less than twelve years later, the shipment in barrels had decreased to nearly one and three-quarter million gallons, while the transport of bulk oil had increased to four hundred eighty-four million gallons. The first modern tanker, the "Glückauf," was built in England in 1886. Her hull, which was 300 ft. long, was divided into compartments by transverse bulk-heads, these compartments being divided by longitu-dinal center-line bulkheads extending throughout the oil spaces. There was a pump room forward of the boiler room, thus providing a cofferdam or safety space. Between the main and upper decks, a narrow trunk extended the full length of the' oil spaces, the trans-verse and longitudinal bulkheads being carried to the upper deck. This allowed for the expansion of the oil from a rise in temperature, and if the tank below the main deck was kept full, the danger of the oil moving with the roll and pitch of the vessel was considerably reduced. Spaces for the carriage of light oil were provided on each side of the vessel outboard of the expansion trunk, while water ballast was carried under the machinery compartments fore and aft. Although vessels previously had been built to carry oil next to the skin of the ship, it is claimed that the "Glückauf" was the first one constructed on the new principle outlined.

Jan 12, 1922

By R. A. Mosser

Production control of aluminum content of low carbon aluminum killed open hearth steels is being achieved by using an oxygen probe unit. Based on the free oxygen content of the bath after block, a preliminary chart for aluminum additions has been established. The aluminum aim is .040%. Controlled aluminum contents will result in eliminating coarse grain heats, high aluminum contents, and a reduction in aluminum costs. By reducing the frequency of high aluminum contents both cleaner and better rolling heats will be obtained. The savings in aluminum costs is an added benefit of lesser importance in comparison to the quality improvements gained by controlled aluminum contents. Although the main goal for the oxygen probe at Republic Steel has been to adapt it for production control of aluminum contents, future usage could be extensive. Immediate plans for using the probe are on degassed material, on fully blocked open hearth heats to improve manganese recoveries and ranges, and on machining grades to control oxygen content. Also by controlling the oxygen content of the steel to as close to equilibrium conditions as possible, cleaner steel will result.

Jan 1, 1972

By Kung-Ping Wang

This is the second installment of two-part article on the Far East. The mineral situation in Hong Kong, Indo-China, Thailand, Burma, Malaya, Indonesia, the Philippines, and British Borneo is covered.

Jan 12, 1951

By Calvin Bjorne, John Keeley

In the face of a highly competitive iron ore market, the Cleveland-Cliffs Iron Co. developed a process now being practiced at the company's Republic mine in Michigan's Upper Peninsula. By this process, a specular hematite crude ore is being beneficiated to produce a high iron-low silica concentrate with a suitable size structure for the production of a high quality pellet. This process involves crushing, primary grinding and primary flotation, followed by regrinding, heating and refloating the primary flotation concentrate. The ores consist predominantly of specular hematite with relatively minor amounts of magnetite and martite in a recrystallized chert gangue. A wide variety of silicates have been identified, particularly in association with intrusives of various description. The more abundant of these are sericite, talc, grunerite and chlorite with some carbonates, primarily calcite.

Jan 6, 1964

INTRODUCTION TO PROBABILITY THEORY The mathematical theory of probability provides the foundation for the interpretations and inferences that can be made from statistical techniques. Probability theory is a broad field of study in itself, and can only be touched on here in order to provide the necessary back- ground for a more complete understanding of statistical analysis. Probability is concerned with the outcome of random events. It had its beginnings in the theory of games of chance which were of great interest to European mathematicians during the last half of the 17th century. The outcome of a random process or experiment is defined as an event. The collection of all mathematical points associated with each event is called the sample space for an experiment. Consider a random experiment having a finite number, n, of possible outcomes, some of which have a characteristic A. What is the probability that A will result from a single

Jan 1, 1980

By David S. Cahn

Pilot-plant and laboratory tests were made on blends of steel plant flue dust and portland cement to determine whether the flue dust could be pelletized for use as a source of iron in dry process cement manufacture. Strength and setting time results showed that an acceptable agglomerate can be made with a Type II portland cement binder. Abrasion-resistant and well-sized pellets were made in a horizontal drum, using a simulated closed circuit, with a binder content of 7.5% and a moisture content below 15%. Pellet quality was found to be relatively insensitive to changes in binder concentration above 5%. Simulations of stockpiling and weathering indicate that little difficulty would be encountered with use of the flue dust pellets in cement plants.

Jan 1, 1972

By Takao Kobayashi

Micro-crack formation zones developed near a crack tip in rocks and ceramics play a significant role in fracture behavior of these materials. In order to study micro- crack formation near a crack tip and its effects on crack behavior, a mica-epoxy composite material was developed. Multi-layer mica flakes were embedded in an epoxy matrix. Under high stress in the vicinity of a crack tip the mica delaminated, simulating the micro-cracking along grain boundaries or crystal planes in rocks and ceramics. A compact tension specimen was fabricated from mica-epoxy composite material. During the test the load and crack opening displacement were measured following the ASTM E561 (R-curve determination) procedure. Through the compliance calibration method the effective crack length and the KR were computed. The experiment clearly demonstrates the formation of micro-cracks and their effects on the overall behavior of the specimen. The paper discusses the significance of micro-crack formation on fracture toughness characterizations, and the advantages of the use of mica-epoxy composite for detailed studies of interaction between the micro-crack formation zone and the specimen geometry and size.

Jan 1, 1982

By William E. Horst, John H. Bassarear

A technique is described which simplifies the standard procedure for measuring the Bond work index of a specific ore and illustrates how to overcome the strict requirements regarding feed size distribution normally encountered in operating plants. Actual results obtained from various process streams in a copper concentrator are presented and the grindability data are discussed in relation to the observed plant performance. This type of information can be used to gain a better understanding of plant behavior and to assist in the evaluation of plant modifications and process control studies.

Jan 1, 1977

By J. Visman

A simplified method of assessing the characteristics of a cleaning unit, including washability curves, yield figures, ash error, separating gravities, and error curve. FOR more than 25 years evaluations of coal cleaning units have appeared in many publications, and during this time considerable progress has been made in developing the theory and techniques of calculating washery results. A variety of characteristics have been defined over the years, many receiving general recognition during the first post-war Coal Preparation Conference in Paris in 1950. Coal preparation has become a science, and the approach to preparation problems is being revolutionized. Formerly, for example, if a coal operator wanted to know the performance of a given cleaning unit for a particular grade of his run-of-mine, he either shipped a carload to the manufacturer for a test run or relied on a report of a test carried out on a coal similar to the one he intended to clean. In modern practice the expensive, time-consuming test work generally can be avoided if the washability curves of the coal in question and the error curve of the cleaner are known. Normally a guarantee can be given on the strength of this information. General acceptance of modern standards has thus reduced the need for pilot-scale models of existing types of coal cleaners. Needless to say, the method requires exhaustive and accurate information on the cleaning unit and on all the additional circumstances affecting its results, information that ultimately can be secured only from actual tests made in the laboratory or in the washery. It is not the purpose of the present discussion to compare the merits of various characteristics, but to describe the general method of calculation, including a method of obtaining data with a minimum of laboratory work. All data presented here were derived from tests made at the plant with portable field equipment, using small quantities of varsol, carbon tetrachloride, and bromoform. It will be explained later that the use of standard fractional ash contents designated normalized ash contents aids considerably in reducing the routine testing of coal cleaners. Like any other statistical procedure, this method has limitations, and it is not recommended for any work in connection with guarantees. Even a varying commodity such as coal, however, will follow the law of large numbers, which is the basic law of statistics, thus allowing simplification of test work without appreciable loss of accuracy. The characteristics needed for evaluating cleaner performance are normally derived from a float-sink analysis of samples of the clean coal and the refuse, followed by ash determinations of the various fractions. Usually a sample of feed is also collected to find its ash content and to make a single specific gravity cut, both in connection with determination

Jan 1, 1955

By Orville R. Lyons, A. C. Richardson

Operating data is presented for a Bird centrifuge used to dewater coal treated at one preparation plant. The data include: (1 ) percentages of solids in centrifuge feed, cake, and effluent and the plant circulating water for a period of four consecutive operating shifts, and (2) screen-sizing data for a number of centrifuge feed, cake; effluent, and combined cake-effluent samples. An evaluation is included of the relationships between fine solids in the centrifuge feed and the total moisture content of the centrifuge cake.

Jan 3, 1950

By Carl R. Christiansen, James J. Scott

Advance mine planning, coupled with good mining practice, can be employed to develop underground space in stone mines for future industrial usage. To assure the developer the maximum return on his investment, initial planning should consider all aspects of the commercial operation, including surface layout, mining, and underground industrialization. The modular concept of mining to compartmentalize the space offers several advantages over conventional methods. Some expenditures can be considered as mining costs with a reduction of profit from stone production while lowering the capital requirements for conversion for usable space.

Jan 1, 1977

By F. E. Marcy

It is not my purpose to write a lengthy article or to attempt the solution of the problem I am presenting, but to call attention to what I believe an important issue, hoping that it may arouse in some one, or in some company, a sense of responsibility. I am referring particularly to modern up-to-date milling plants discharging tailings which under existing conditions cannot be further treated or from which a recovery cannot be made at a profit, but where a quantitative and qualitative analysis shows that a portion of these tailings might profitably be treated at some future time when our metallurgical knowledge has advanced, when we have cheaper power, chemicals, labor or other advantageous conditions. Early Methods In our early milling methods very little attention was given to the care of tailings. It was thought that if the mill could be located by a stream or a river where the final disposal of the tailings could be forever lost sight of, it was highly desirable. We can now see and estimate what was lost in these rich tailings, not recoverable from the streams and the great rivers. Fortunately for many, the depositing of tailings in these streams and rivers was objected to by the farmers and finally prohibited by the State Legislatures. In looking back over our past milling methods, it seems that the first endeavor was to make the maximum amount of money for a particular period, or year, regardless of the future, the depletion of the mine, or the conservation of the total mineral content. The dumping and sluicing of 3000 tons per day, for a period of many years, of a copper tailing carrying 12 lb. of recoverable copper together with its portion of precious metals, the thousands of tons of valuable metal contained in the tailings that have been carried away by Silver Bow Creek, the streams of the Coeur d'Alene, the Flat River and Colorado districts, the enormous quantities

Jan 1, 1918