Search Documents

By R. A. Feemster, C. M. Rader

Because of the necessity for taking regularly occurring open-flow tests in prorated high-pressure oil fields, much gas is turned to atmosphere by way of vertical vent lines leading away from the oil and gas separator. In the past, measurement of such gas has been accomplished by several methods, usually by use of the open-flow Pitot tube. The use of the closed-flow Pitot tube has been avoided apparently chiefly because the ordinary vent-line hook-up makes it necessary to apply the instrument closer to a bend, valve, or obstruction in the pipe than is recommended by rules of good practice. The many advantages that would result from the application of the closed-flow Pitot tube prompted investigation of the actual effect upon quantity rate of flow measurements computed from data obtained with the tube in a normal working position, which is closer to the tee at the base of the vent riser than is usually considered as giving highly accurate results. An effort Was first made to compare the results thus obtained to those under ideal conditions and at high velocities To make this comparison, knowledge of the characteristics of gas flowing at very high velocities is essential. Research for such information indicated that little or no work had been done that would give data necessary for such a comparison, therefore the problem was changed to a test designed to determine the relationship between quantity rates of flow as measured by an orifice meter and a Pitot tube placed at the center of a pipe eight diameters from a tee or ell at the base of a vent riser, through which gas is flowing under low pressures at very high velocities. To determine this relationship, a series of tests was run on a number of 8-in. iron-pipe vent riser., in which the Pitot tube data were taken at the position as stated above. Gas from a wet-gas gathering system was passed through an orifice meter setting and thence to atmosphere by way of the vents. Data were taken simultaneously from the orifice meter and Pitot tube from which computations for comparisons were made. The actual method of comparison is discussed later in this paper. Since Pitot-tube information is usually given in general terms, and not readily usable, it will be the purpose of this paper to discuss the applica-

Jan 1, 1934

By R. V. Ramani, Robert Stefanko

The more stringent ventilation requirements of the 1969 Act have created a greater need for improved network analyses. More air is required at the last open crosscut (9000 cfm) and for the first time a minimum quantity is specified for the face (3000 cfm). Severe restrictions are placed on both belt and track haulage, and the intake air cannot contain more than 2 mg per cu m of respirable dust, to be reduced to 1 mg later. Larger tonnage and longer life mines are the trend today, necessitating multiple fans and shafts. Yet relatively little engineering goes into designing the mine ventilation system. In this paper a ventilation system is designed for a typical Pittsburgh block system, manual calculations are made and then checked by a computer solution. The computer is the ideal tool to try out proposed changes on paper to insure that the entire mine is properly ventilated and no costly adjustments need be made by dumping air. While it is theoretically possible to solve complex ventilation network problems by hand, it is not practical to do so because of the tremendous man-hours required and the many opportunities for errors. Thus the digital computer is indispensible to the ventilation engineer and newer improved ventilation programs are being developed to more realistically model mine ventilation networks. Suggested ventilation changes to comply with the new regulations are also critically evaluated.

Jan 1, 1973

By E. G. Banks

This paper is presented in the belief that metallurgists and chemists will be interested in the practice of grinding in tube-mills in connection with stamps, especially since the records of working here given extend over a lengthy period of time (since May, 1905). The ore from the Waihi mine—more especially that produced in the upper levels—contains a large proportion of hard, chalce-donic quartz, and the gold exists in an exceedingly fine state, conditions which necessitate very fine crushing in order to obtain a high extraction of the precious metal. Before the introduction of tube-mills at the 90-stamp Waihi mill, it was found necessary to stamp through 40-mesh (1,600 holes per sq. in.) woven wire-screens, having a fairly high discharge. The pulp then graded : Per Cent. Per Cent. On 50-mes11, .- 0.1 On l20-mesh ..8.77 On 60-mesh, . 8-74 On 150-mesh,.... 7.48 On 80-mesh,... 16.06 Passed 150-mesh,... 55.19 On 100-mesh,.... 3.66 The stamp-dnty was 2.89 short tons per stamp per day, or a total of 260 tons daily. Although the extraction on this pulp was: gold, from 88 to 90 per cent., and silver, from 74 to 78 per cent., it was recognized that finer grinding of the sands would prove beneficial, provided a machine could be found to do this work economically. Various grinding-mills and pans were tried, but without satisfactory results, the particles of sand being so hard that the capacity of any of the machines was too small to be economical. The results of grinding in tube-mills in other countries were so satisfactory that three tube-mills mere erected at the Waihi

Jan 1, 1908

By Raymond Franz

Of the many types of capital equipment found in a surface operation, draglines and mining shovels are probably subjected to the most severe service. Yet, some excavators have seen a generation or more of continuous service-proof, if any is needed, of their ruggedness. To keep these expensive pieces of machinery operating, a continuing maintenance program which includes field weld repairs is essential. During an excavator's working life, minor cracks may appear in parts of the steel structure, caused by fatigue and sometimes material defects-defects so small they could not be detected during manufacture.

Jan 6, 1978

By K. V. S. Sastry, V. P. Mehrotra

A laboratory investigation was carried out to study the influence of asphalt, bentonite, and corn starch binders on the pelletization kinetics of coal fines and on the quality of the resulting pellets. Pellet quality was evaluated in term of the compression strength, impact resistance (drop test), abrasion resistance, and resistance to severe weather conditions. The amount of binder addition did not significantly influence the pellet growth kinetics. However, the pellet quality varied markedly depending upon the type and the amount of binder wed. Experimental results are explained on the basis of the mechanism of interaction between the coal particles and the binders. Of the three binders tested, corn starch proved to be the best in all respects but for the resistance to water penetration. Finally, a combination of corn starch (imparting strength) and asphalt emulsion (imparting resistance to water penetration) was found to yield the best quality coal pellets.

Jan 1, 1983

By L. R. Flint, W. L. Freyberger, W. J. Howarth

W. L. Freyberger (Director, Institute of Mineral Research, Michigan Technological University, Houghton, Mich.)-The authors are to be complimented on their theoretical analysis of a column flotation process, and the comment I wish to make is not related to that analysis, but to the use of the word "countercurrent" to describe that process. Strictly speaking, the process the authors have described is countercurrent only in the sense of particle-bubble contact. That is, as solid particles and air bubbles pass through the column, the leanest flotation feed (the tailing) comes in contact with the greatest concentration of mineral-free bubbles. However, air bubbles alone do not comprise the complete extracting phase in a flotation system. A second component of this extracting phase is the collector, which is really the extractant inducing transfer of mat-

Jan 1, 1972

By Donald L. Everhart

Beginning in 1906, data has been compiled on the distribution of uranium in phosphate de- posits. Particular emphasis has been placed on uranium in phosphate by a number of geologists and geochemists in the US Geological Survey in research sponsored by the US Atomic Energy Commission (now Nuclear Regulatory Commission) and the US Department of Energy (DOE) during the 30-year period from 1951 to 1981. A comprehensive study of uraniferous phosphate resources the United States and the Free World was completed, under the auspices of DOE, in 1979. Apatite is the main carrier of uranium in phosphate. Uranium generally replaces calcium in the mineral lattice. In marine phosphorite throughout the world, the uranium content is characteristically in the range of 0.005 to 0.02% by weight. Phosphorite takes in uranium by structural substitution in apatite or other mineral phases, by absorption, or by the formation of independent mineral phases. Apatite derived from the interaction of ground water, guano and limestone is typically relatively low in uranium content-in the 0.001 to 0.005% range. In primary accessory apatite of igneous rocks, as well as magmatic and metasomatic apatite segregations of alkalic rocks and carbonatite, uranium content is generally between 0.001 and 0.01%. In all these phosphate deposit types, secondary enrichment of uranium through

Jan 1, 1983

By David Keys

APPLIED geophysics is the youngest child of that old branch of learning, that has been known from Aristotle's time as physics-the constitution and laws of nature. The mother science, with the help of mathematics, has given birth to many children, who, on becoming of age in the scientific sense, wedded more practical applications which later became known as electrical engineering, physical chemistry and acoustical engineering. Some vigorous sons still retain the family name, among which the most recent to take its place as a division of science is geophysics, which deals with the physics of the earth. Geophysics in its broad sense has many departments-meteorology, oceanography and seismology, to mention only three. Within the past 20 years, however, a special interest has arisen in the application of physical principles to, problems in geology, mining and civil engineering, with the consequent rapid growth of what has now been called "applied geophysics." Applied geophysics in this narrower sense is the application of experi-mental and theoretical physics to determine variations: and discontinuities in underground structures that cannot be ascertained from surface inspec-tion. It seems evident, then, that the physics department is the natural place in a university where the principles and methods involved should be taught and developed, for the physicist will also have had the requisite training in mathematics that the proper understanding of many methods now used will require. A knowledge of the procedure and principles, however, is not sufficient for the successful application of geophysical, methods. One may know the dynamics of flight of golf balls and of impact and yet not play a par game of golf ! The proper selection and use of the right club to suit the circumstances of the lay of the ball and an acquaintance with the possibilities and limitations of the strokes as well as the practical execution of the play is essential to a successful game. So, also, in the application of geophysical methods, it is important for the geophysicist to use the best device under the conditions presented, to know the limitations of the conclusions deduced from his physical measurements and to make the proper interpretation of the results. A knowledge of geology will be of great aid in coming to the correct con-

Jan 1, 1938

By J. B. Scuffham, G. A. Rowden

The use of ammonia as a leaching agent has been well-documented but only recently have its advantages been fully exploited on a commercial basis. When compared with conventional sulfuric acid leaching processes, the major advantage of ammoniacal systems is their ability to reject iron and many acid consuming gangue materials. Although metallic copper, nickel, zinc, etc. are dissolved rapidly in ammoniacal liquors at ambient temperature in the presence of air the sulfide ores of these metals are more resistant to this treatment. Sherritt Gordon Mines in Canada treats sulfide concentrates at its Fort Saskatchewan plant under pressure with ammoniacal am- monium sulfate solution to solubilize the non-ferrous metal values. Typical leach operating conditions are 80-95°C and 115- 128 psig. Although the metals present in the ammonical solution could be recovered via solvent extraction techniques, Sherritt Gordon Mines currently operates a pressure reduction process using hydrogen to yield metal powders directly from the ammoniacal solution. The basic Sherritt Gordon technology has been applied world wide for the treatment of nickel/cobalt concentrates.

Jan 12, 1973

By Robert W. Zimmerman

POROUS SOLID COMPRESSIBILITIES There are four different compressibilities associated with porous solids, each relating the fractional change in either bulk volume or pore volume with the change in either pore pressure or confining pressure. These will be referred to as Cbc, Cbp, Cpc, and Cpp, with the first subscript denoting the relevant volume, and the second subscript denoting the relevant pressure. They are defined as: [ ] Note that minus signs are included in two of the definitions so that each of the compressibilities will always have a positive value. In general, each compressibility depends on the elastic moduli of the matrix material, the porosity, and the exact geometry of the pores. Taking the latter factor into account calls for separate analysis for each different pore shape, which of course can only be attempted for a few relatively simple cases. But lower bounds for each of the four compressibilities can be found, independant of pore structure, in terms of only the porosity (0) and the elastic moduli of the matrix material (any pair chosen from K, E, G and V). The first step is to find relationships between the four compressibilities, starting with the following observation: If a porous solid made of a linear elastic, isotropic and homogeneous matrix material is subjected to uniform hydrostatic pressure of magnitude P on its external and all of its internal (pore) surfaces, the state of stress in the solid will be exactly the same as that which would occur

Jan 1, 1982

By LeRoy Scharon, P. Uhley

TEST gravity surveys were made in the Washington County barite district of Missouri on properly owned by the Baroid Sales Division of the National Lead Co. This property is located just northeast of Richwoods in the northeastern corner of Washington County, Fig. 1. The area to which the surveys were confined comprised approximately 5000 acres, of which some 525 acres were surveyed gravitationally. Gravity observations were made at 2600 points within the area, observations being confined to relatively clear and gently sloping ground. Part of the area was heavily wooded, and the terrain too rugged for either the occurrence of a commercial barite deposit or a feasible gravity survey. The relief along the central drainage, Ditch Creek, was about 140 ft, the maximum difference in elevation being 400 ft in a distance of 3½ miles. The purpose of the test gravity survey was to determine whether the gravity method of geophysical prospecting might be applied in the exploration for barite deposits in the Washington County barite district, since a satisfactory systematic procedure had not been devised to explore and ultimately determine barite ore reserves with desired accuracy. No previous geophysical work with respect to barite is known to have been done in this area. Stratigraphy: The formations over which the barite deposits occur' are Paleozoic in age, representing rocks involving sandstones and dolomites unconformably underlain by pre-Cambrain granites and rhyolite porphyries. The areas covered by the granite survey were directly underlain by almost

Jan 1, 1955

By Albert Sauveur

SOME writers believe that when austenite transforms completely into pearlite on slow cooling through the thermal critical range, such transformation does not imply the formation of any of the so-called transition constituents: martensite, troostite and sorbite. Might it not be claimed with as much justification that when water freezes it does so suddenly, solid ice being obtained without passing through the intermediate stages of ice and water? Obviously, regardless of the speed of solidification, this would be erroneous. Before reaching the completed solid condition, this must of necessity pass through an unbroken series of stages when the system consists of mixtures of water and of ice, the former decreasing and the latter increasing in amount. Are not these "transition" stages in the freezing of water similar to the transition stages occurring in the transformation of austenite into pearlite? To clarify, let us consider in Fig. 1 the mechanism of the transformation of eutectoid steel from its austenitic to its pearlitic condition as it cools slowly through its thermal critical range. It is generally admitted that this transformation is the result of two distinct phenomena: (1) the allotropic change of gamma iron into alpha iron and (2) the crystallizing out of solution of the carbide Fe3C. Whether this crystallizing of Fe3C implies also its formation is immaterial for our purpose. In other words, whether it is the carbon in atomic dispersion which is present in gamma iron or molecules of Fe3C has no bearing upon the matter to be discussed. The transformation of gamma iron into alpha iron cannot take place suddenly. It must of necessity be progressive, regardless of the speed with which it may take place. At A, for instance, there would be present AB gamma iron and BC alpha iron. The distance MN does not refer to falling temperature, but to the passage of time. It may be assumed that the transformation takes place at a constant temperature (the Ar321 point). In a similar way, the crystallization of Fe3C out of the austenite solid solution must be progressive as depicted between M and N. At A there would be present AB gamma iron, BC alpha iron, CD carbon dissolved in gamma and in alpha iron and DE Fe3C. This condition may be described according to individual preference as martensite or troostite. To sum up, can the metal pass from condition

Jan 1, 1931

Prof. J. W. Richards, South Bethlehem, Pa. (in reply to several questions):—The cut representing some of the round briquettes which were under test shows that, at the brcaking-stresses, they break into lumps, and do not disintegrate into powder. The process is simplicity itself. I have followed the different processes for sintering iron-ores and flue-dust, am interested in all of them and wish them all success; but this process appealed to me strongly by its simplicity. It is in line with a method which I once tried to work out myself, but which never came to anything, namely, the agglomeration of fine iron-ores by means of Portland cement. As small an amount as 5 or 6 per cent. of Portland cement will enable fine ore to agglomerate and set into a briquette, but when I came to estimate the cost, I found it was a little too high. The Schumacher process, curiously enough, does not work well on iron-ore, but flue-dust thus treated does harden and give a strong briquette. In my attempts to find a reason for this difference, it has occurred to me that possibly the particles of flue-dust had been coated over with some sublimed silica, which might be an agent in the setting. But I found by experiment that neither sublimed silica, nor ordinary silica, nor ordinary alumina, would briquette. Chemically pure iron oxide briquetted quite hard; but the application of pressure is a necessary part of the operation. If simply moistened with the solution and allowed to stand it does not set hard, but the more pressure applied to it the hardcr it sets. Evidently the flue-dust particles must be pressed very close together in order to get the small proportion of active material wet, so that the particles shall act at their points of contact; for it is evident that only at the points of contact does the cementing action take place. The reactions are facilitated by considerable pressure, bringing the acting particles close together, and may go on with

Jan 1, 1913

By Kichizo Niwa

A LTHOUGH studies on the roasting of ferrous A sulfide have been carried out by several investigators, some disagreements still remain among those results. Schwab and Philinis1 have measured the rate of oxidation by a precise thermobalance and have concluded that the rate is controlled by diffu-

Jan 1, 1958

By Thomas M. Drown

AT the meeting of the Institute in New York,, in February, 1880,* I described a process of determining sulphur in metallic sulphides, with especial reference to the determination of pyrites in coal. The process, as then described, is as follows : A solution of sodium hydrate, of 1.25 specific gravity, is saturated with bromine. If an excess of bromine is used it must be neutralized by the addition of a :little more sodium hydrate. The pulverized mineral or coal is moistened with 25 c.c. of this solution and heated, then hydrochloric acid is added cautiously to just acid reaction. This operation is repeated with another 25 c.c. of the alkaline solution, and again rendered acid. The mixture should be kept hot. The contents of the beaker or dish are then * Transactions, American Institute of Mining Engineers, vol. viii, p. 569.

Jan 1, 1881

By Mourad Aissa

From our previous work (Gardner, Aissa, and Verghese, 1982) on determining the residence time distribution of ball mi 11s from radiotracer data taken in closed-circuit operation without interruption of the process, it occurred to us that the data taken for this purpose also contained information on the breakage rates of all the sizes present. It is the purpose of the present work to evaluate methods to obtain breakage rates from this data. A numerical solution for the impulse injection and subsequent detection of radiotracer in a closed-circuit linear comminution process is developed and used with typical breakage parameters, residence time distribution, and classifier functions to study and evaluate these methods.

Jan 1, 1984

By Eizo Yabuuchi, Yukito Imanaga

INTRODUCTION In treatment of mine drainage, it is well known that the neutralization by calcium carbonate is far better than by slaked lime because of cheaper cost and better precipitability of its deposit. However, in case of iron ion contained in the mine drainage consists of ferrous salt, the ferrous salt must be oxidized to ferric salt before neutralization, because the ferrous salt does not react with calcium carbonate. At Yanahara Mine, during the period of 1950 through 1956, ferrous ion in the mine drainage had been oxidized to ferric ion, simultaneously neutralized by adding calcium carbonate into the aerated drainage. During the period of 1961 through 1974, after passing through many kinds of treating methods, the neutralization had been carried out by addition of calcium carbonate into the drainage after oxidized its ferrous ion to ferric by using nitrous gas as an oxidizing catalyzer. Meanwhile we had made an experiment on the oxidation of ferrous ion by utilizing iron bacteria, and developed a method which oxidized ferrous ion in large quantities briefly by cultivating and concentrating iron-oxidizing bacteria. Since 1974, we have been operating successfully for treating the drainage at Yanahara Mine by means of utilizing these bacteria.

Jan 1, 1976

By James Aston

INDICATIVE of the practical importance of the achievement of James Aston , recipient of the Robert W. Hunt Medal for 1930, is the following prosaic item from the financial columns of a recent issue of a New York newspaper. "According to private advices from Pittsburgh, production costs of the A. M. Byers Co. for 1929 were reduced about $5 a ton by the use of the Aston process for making wrought iron pipe. A greater saving is anticipated for 1930, when more of the company?s requirements will be produced by the new method."

Jan 1, 1930

By Milton E. Wadsworth

Hydrometallurgical processing of ore deposits by solution mining or in situ techniques requires the interfacing of technologies as diverse as hydrology, geology, chemistry, and rubblization. This synthesis represents one of the main challenges to in situ processing due to the inherent complexity and vocabulary of these well-developed technologies, and to the general lack of appreciation for the depth of knowledge and endeavor in each separate field. No better example of the need for such interfacing of technologies exists than that of solution mining. How well these technologies interface depends upon the size of the operation and its financial capability to use the information and technology available. It is inconceivable that any one individual can optimize each potential contribution alone; consequently, some areas are usually neglected or simply are not fully appreciated. When one examines what must be done at a future date to develop and exploit a remote solution mining system, it becomes obvious that each discipline must effectively communicate the needed background information to make the project a synthesized whole.

Jan 12, 1977

By R. W. Raymond

(Reprinted With some additions and changes from the Engineering and Mining Journal)] THE death of Prof. Samuel Benedict Christy on the 30th of November,. at the age of 61 years, cuts short a brilliant and influential professional career. He was born in San Francisco, Aug. 8, 1853, and was graduated as Bachelor of Philosophy at the University of California in 1874. For the five years that followed, he studied mining and metallurgy as a post-graduate in the same institution, serving also as instructor in analytical chemistry, and becoming in 1879 instructor in mining and metallurgy¬a position which he held until 1885. During this period he became known also by his contributions to technical literature, the earliest of which, perhaps, was his report on the Monte Diablo coals (in 1875); but the first which drew my attention to him was an exceedingly able discussion (in 1879) of the genesis of the quicksilver deposits of California, in which he followed with much acuteness and originality the lead of Professor Becker, who had been teaching at the University of California. The notion of the thermo-aqueous formation of such deposits was then new; and the laborers in a field now familiar to every student deserve the credit due to pioneers. For some years the subject of quicksilver seems to have occupied much of Christy's attention. In 1877, he described the mines and works at Almaden, Spain; in 1884, the Imperial quicksilver works at Idria, Austria; in 1889, the New Almaden mines of California. But his great work was the creation of the school, of mining and metallurgy at the University of California, which may be said to have begun with his occupancy of a full professorship of these branches. It is not necessary here to recount the early difficulties and perils of the University, and its long struggle for academic independence of political control or interference. The battle is over, and the institution is now upheld by the intelligent loyalty of the citizens of California, without regard to party. But while the issue was uncertain, the development of special schools of applied science was scarcely practicable. Doctor Becker and William Ashburner had given up the school of mines as a hopeless task when Christy, younger and less experienced, took it up. As he wrote me in February, 1901-

Jan 4, 1915