Search Documents

By H. L. Talbot, R. S. Young, A. Golledge

THE differentiation of, oxidized forms of lead from lead sulphide in complex products by chemical analysis is of considerable importance to certain mining and metallurgical companies. A method for the separation of "oxide" lead, (non-sulphide), from sulphide lead, based on the solubility of the former and virtual insolubility of the latter in concentrated ammonium acetate solution, has been employed for many years in the industry.1,2 Unfortunately this solvent, while satisfactory for lead sulphate and carbonate, is without action on lead phosphates or vanadates, with the result that at Rhodesia Broken Hill Development Co. where these latter minerals are present, they have counted as sulphides when using this procedure. For the control of operations in the new concentrator it became necessary to have a closer check on sulphide lead than could be obtained by the only current method of differentiating this constituent from oxidized lead. For some time this problem has engaged our attention, and after a large number of solvents had been tried, the following procedure was evolved. Like all methods depending on selective solution in a complex material, it will not give 100 pct separation into oxide and sulphide portions. Because of the ease of oxidation of galena this is almost an impossibility. Our procedure will, however, give a recovery of 99-100 pct of the oxidized lead, contaminated with very small quantities of lead sulphide, and a corresponding recovery of 97-98 pct of the sulphide lead. The procedure is simple and reproducible, and gives results quite satisfactory for routine control purposes. EXPERIMENTAL For this work standard samples of the following pure lead minerals were obtained from Broken Hill, Northern Rhodesia. These were hand-picked specimens, and were carefully ground to - 200 mesh. Since it was realized that a fair-sized sample would be necessary for this work to thoroughly test the large number of procedures we had in mind, a compromise had to be effected between a few grams of very pure minerals and a large sample of lower grade material. For this work the presence of gangue was not deleterious, so long as the oxide lead minerals did not contain lead sulphide, and vice versa. Table I shows the lead minerals used, and their total lead content, both theoretical and actual. Apart from the pyromorphite the minerals are seen by analysis to be quite pure. Many solutions were tried in an effort to dissolve the oxidized lead minerals and

Jan 1, 1947

By John F. Abel

A good mining engineer is supposed to make a good mine. What then makes a good mining engineer? There certainly are a lot of answers to that question. The answers depend on whether you are one, work for one, or employ one. There are several cliches about mining engineers, and there is some truth in them-as there usually is in any stereotype. Hollywood chose Jeff Chandler to portray a mining engineer in Foxfire. The image here was of an almost one-man mining operation. When Chandler picked up a jackhammer, cradled it in his gut and started drilling out a tunnel round, it gave one the hives. I would have liked to see him finish just one round that way. There are limits to what even the most hairy-chested of us will try. We can assume that Hollywood feels it needs to over- draw any profession to add impact.

Jan 1, 1970

By Cornelius Kelley

THE American producers of silver are keenly alive to the importance of the silver problem and its vital effect on the mining industry in Montana and other States where precious-metal mining constitutes a basic industry. There are so many ramifications to the subject that one is tempted, no matter from what angle an approach is made, to digress along lines that inevitably lead into a maze of social, economic and financial problems, through which no clear pathway is marked, and regard¬ing which no definite opinion can be expressed, as the ultimate solution is dependent upon the policies adopted and carried out by the more important Governments with reference to their fiscal requirements and currency systems. The situation may be summarized in two questions First, what, if any, plan have the silver producers, as being the most directly interested, to offer in meeting the situation which will confront the industry upon the termination of purchases of domestic silver under the Pittman Act? Second, what, if any, assistance can be extended by the Government in connection with the problem? In answer to the first inquiry, while the matter has been the subject of discussion among the principal producers, they have been unable to formulate a defi-nite plan, principally because they have been and are dealing with a subject embracing many unknown fac-tors; and second, it has been felt that before any plan is adopted there should be indicated the extent to which cooperation on the part of the Government may be depended upon to enable a proper study of the situation to be made. In order to explain these rather cryptic statements, a general review of the situation may aid. Whatever differences of opinion there may have been in the past upon the subject of bi-metallism or the establishment of a fixed ratio between the coinage value of gold and silver, it will probably be conceded that it would be neither wise nor expedient to attempt a revival of this discussion, nor to undertake to solve the question by the adoption of such a remedy. Issues of contro-versial economics must be avoided, if possible-political economics will destroy rather than assist constructive effort.

Jan 2, 1923

GENTLEMAN: The year 1928 was another in the history of the Institute which was marked by quiet growth and steady progress. The total membership as of December 31, 1928, was 8703 as compared with 8438 on December 31, in 1927. Again the main increase has been in Members and the number of Junior Associates is less. As will be seen also by the Treasurer's report, the increase is reflected in larger receipts for dues indicating that fewer have had to be dropped for non-payment. There has been a gratifying increase in the number applying for reinstatement and it seems clear that interest in and attachment to the Institute has notably increased. The year was signalized by the merging of the Rocky Mountain Club with the Institute which brought to our roll one hundred and forty who were not previously members from among the men who have made the West. It also brought to the Institute a strong tradition of good fellowship and a fund of over $100,000, the interest from which is to be expended so far as may be, for purposes beneficial to the Western states. The Endowment Committee expects to see other and similar funds entrusted to the Institute and the Board has already appointed a special committee to consider all projects for expenditure of the revenue from them. It is felt that with the organization and personnel available in the Institute even modest revenues can be made to yield large returns in the way of scientific and technical knowledge. Within the year also, a third great Division has been organized within the Institute, building on the foundation of the old Iron and Steel Committee. The new Division signalized its independence by joining the Lake Superior Mining Institute in a visit to the Menominee Range in September and by furnishing material for a special volume of 353 pages, "Iron and Steel" Technology in 1928," printed and distributed in December. The Institute of Metals Division held its fall meeting with good attendance as one feature of National Metal Week at Philadelphia in October, and published its volume of Proceedings, running to 836 pages, in August. "Petroleum Development and Technology in 1927," 844 pages, came out in June and recorded the work of the Petroleum Division. A most interesting Fall meeting was also held by the Division at Tulsa,

Jan 1, 1929

By C. K. Leith

MANGANESE is one of the minerals which is principally consumed in countries other than those of origin. Nearly 85 per cent of the pro-duction is used by the United States, England, Germany and France, and roughly a third of the total is used by the United States alone. On the other hand, over 85 per cent of the world production comes from Brazil, Russia, India, the Gold Coast of Africa, and the Sinai Peninsula. It follows from this fact that practically all manganese moves across international boundaries in raw or alloy form, and much the larger part of this movement is for considerable distances and is ocean borne. There is no indication that any one of the principal consuming countries can develop even approximately adequate supplies of its own. Under abnormal war conditions, with high prices and changes in metal-lurgical methods, only 35 per cent of the needs of the United States was met from local sources, and under our recent tariff only 11 per cent. There are thousands of manganese deposits scattered about the world, but only a very few which can figure largely in supplying requirements on a modern scale. The known reserves, together with highly probable extensions and explora-tions now under way, indicate no shortage from a world standpoint for many decades to come. The production and marketing of manganese is going steadily into fewer and stronger hands. The steel in-dustry uses over 90 per cent of all the manganese mined, and is acquiring control of a considerable part of the production in all of the principal fields-the Germans in Nikopol, the English in India and Gold Coast, the Americans in Georgia, India, Gold Coast and Brazil. Some of the controlling companies are of international scope. Concentration of commercial control is a notable tendency. A natural consequence is the growing un-easiness of smaller consumers the world over about their ultimate supplies and desire to know more definitely how and where manganese supplies will be controlled in the future. The sources of supply are few enough to warrant the belief that more or less monopolistic ele-ments of control are not impossible.

Jan 5, 1927

By Jerome Alexander

It is an outstanding fact of Nature that many of the practical properties of substances are dependent, not on their ultimate chemical composition, but on the kind and degree of aggregation of their constituent particles. Thus, a granite boulder is unmoved by wind or water, but if reduced to a fine dust it will be blown about by the wind and washed away by the rain. Carbon in one crystalline state of aggregation (diamond) is the hardest known substance, whereas in another crystalline state (graphite) it is so soft that it is used as a lubricant. Laying too much stress on the mere chemical analysis of substances is apt to obscure the fact that the nature of the aggregation of their particles is always a factor of importance, and sometimes the most important factor. Colloid chemistry deals with matter in a very fine state of subdivision; its sphere begins with particles just a little smaller than a wave length of light and extends down until they blend into molecular dimensions. With particles of this size, such phenomena as surface tension and adsorption, which depend on the development of free surface, become enormously magnified. Thus a cube of 1 cm. edge has a surface of only 6 sq. cm.; but if it is reduced to colloidal dimensions by being cut up into cubes each having an edge of 0.01 µ (0.00003 mm.), it will yield one million, million, million (1,000,000,000,000,000,O~) such cubes, having a combined area of 600 sq. m., or 21,274 sq. ft. The tiny force with which a drop of rain clings to the window pane becomes a factor to be reckoned with, if the surface involved is increased millions of times. From the colloid-chemical viewpoint, metals and alloys may be regarded as jellies or sponge-like structures,. the viscosity or stiffness of which at ordinary temperatures is exceedingly great; and like all jellies their properties are dependent on the composition and degree of dispersion of their constituent phases. These, in turn, depend on chemical composition, mutual solubility, speed of chilling, subsequent mechanical and heat treatment, etc. In fact, in preparing metals and alloys for practical use, we remove undesirable constituents (as in the conversion of pig iron into steel), add desirable constituents (as in

Jan 1, 1919

By James F. Lewis

The death of Josephus Flavius Holloway, for twenty-one years an active and beloved member, and twice a Vice-President, of the Institute, cannot be allowed to pass without some expression on the part of his brethren of mingled grief and gratitude—grief that we have lost his genial and inspiring presence ; gratitude that we have been privileged to know one who lived " To make the world within his reach Somewhat the better for his being, And gladder for his human speech." The present sketch of his career and character is offered as a sincere, though inadequate, expression of these feelings. Mr. Holloway's father, Joseph T. Holloway, born, in 1796, in Sunbury, Pa., and yielding in his youthful prime to the prevailing impulse of his generation, started alone, with knapsack

Jan 1, 1897

By D. J. Carney, J. Chipman, N. J. Grant

G. Derge—With the development of this last weapon, there is not much of a chance for hydrogen. It is certainly a very interesting paper, and it gives us more confidence in sampling liquid steel for hydrogen than we have ever had before. This satisfactory work gives considerable confidence to all of the chilled methods of sampling which should be more or less successful depending upon the degree of chilling obtained. J. T. MacKenzie—How do you handle a nonmagnetic specimen in that device? D. J. Carney (authors' reply)—I left that out in going over the analytical procedure. For the 18-8 steel, what was done was to get some iron wire which was degassed. One turn of wire was made around the sample; it was inserted into the analytical apparatus, and that was enough to allow the magnet to pull the sample and drop it in the furnace. Other methods could be devised for this apparatus to do the same thing. This was just a quick method. C. E. Sims—This method of sampling and analysis is very ingenious, and the results obtained attest to a satisfactory degree of accuracy. It was noted in the paper that the samples are satisfactory only when there is a complete absence of pipe. This should be empha- sized, particularly in view of the fact that they are cut off under water. Some reservations are held in regard to the adequacy of the method of sample storage prior to analysis. Cooling on dry ice undoubtedly slows down the rate of diffusion to a marked degree, and it obviously suffices when the analysis is made within a few hours. All of the samples, except some of high-nickel steels, were analyzed within 12 hr. It is still unknown how long this method would be safe. In the work at Battelle Institute, it was impracticable always to start analysis within 12 hr for various reasons. Some samples did not reach the laboratory for several days, and some were held as long as a month before analysis. During this period, they were held over mercury, and the gas evolved at room temperature was collected and analyzed. It should be mentioned that both the mercury and the container must be kept very clean.

Jan 1, 1951

By J. S. Ll. Leach, J. B. Cohen, M. B. Bever

IN the work reported here, the heats of formation of a copper-rich Cu-Sn (a) solid solution and of the Cu.Sn (0 phase were measured by tin solution calorimetry. An approximate determination of the heat effect attending the precipitation of 6 from a supersaturated a solid solution was also made.

Jan 1, 1955

ALMOST all the hazards productive of accidents are present in churn drill operation-exposed electrical cables, open machinery, moving parts located overhead, exposure to weather, and movement of heavy machinery-all are part of the job. But, a check list of danger spots and full use of countermeasures will produce maximum safety here, as on any other operation.

Jan 8, 1953

By Nicholas Kowall, K. L. Clark

Maximum furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. Work oF Other Investigators In I938, Burns, Moore and Archer published & curve? that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the rallge found in construc-tional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only o.2o per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E 43xx steels, His procedure consisted of chill-casting a test bar that was large enough to give a a that could be prepared for Brinell indentations. The test piece was quenched immediately after solidi fication was complete and hardness readings were taken, so that the carbon content could he read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. Experimental Work Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By K. L. Clark, Nicholas Kowall

Maximum furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. Work oF Other Investigators In I938, Burns, Moore and Archer published & curve? that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the rallge found in construc-tional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only o.2o per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E 43xx steels, His procedure consisted of chill-casting a test bar that was large enough to give a a that could be prepared for Brinell indentations. The test piece was quenched immediately after solidi fication was complete and hardness readings were taken, so that the carbon content could he read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. Experimental Work Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By W. W. Weigel

THE mines of the St. Joseph Lead Co. in St. Francois County, Missouri, form a roughly triangular area of about 45 square miles. Locally this is known as the Lead Belt. The four operating mines in the area at present are the Federal, Leadwood, Desloge, and Bonne Terre, in decreasing order of mine area and daily production. Mining began in 1864 and has been carried on in the district continuously since that time. [ ] As a group, the Lead Belt mines now handle 20,000 gal. per min. of water, average head about 465 ft., against a normal daily ore tonnage of 21,200 tons. For a six-day operating week this gives a ratio of 6 ½ tons of water per ton of ore. Total average pumping in 1931 was about 15,000 gal. per min. Since that time a large area of virgin territory has been opened, much of which has had temporary flush flows. About 75 per cent of the water enters in certain restricted very wet areas. Production figures are given in Table I. The figures by divisions for 1931 and 1941 are not exactly comparable, as there were several transfers of pumping loads from one division to another during that period of time. GEOLOGY The basement formation in the Lead Belt area consists of the pre-Cambrian rhyolite porphyry and granite. Overlying this is the La Motte sandstone, of Middle Cambrian age, which offers a good medium for circulation of water. It varies in thickness up to 400 ft. Above this is the Bonne Terre dolomite, approximately 375 ft. thick, which in turn is overlain by the 150-ft. Davis shale. The formations above this, present in the Lead Belt in small areas only, are of minor importance. The ore bodies occur as large, horizontal tabular masses or as long, narrow runs; they are found throughout the Bonne Terre but largely in the lower 150 ft. The rather indefinite contact with the La Motte is a favorite ore horizon. Mining is entirely by open stope and pillar breast systems. To the south, west, and north of the district, sandstone outcrops are few and limited. Heavy faulting bounds the district on those sides and probably there is little if any artesian circulation from those directions. To the east, the La Motte rises to an outcrop area of about 40 square

Jan 1, 1943

By A. W. Allen

THE technological study of the treatment of gold and silver ores has been largely responsible for the phenomenal strides which have marked the progress in this branch of metallurgy during recent years. In no other application of science to industry is system more imperative at every stage; correct formulation of result is only second in importance to efficiency of operation. Progresss in method has been largely the result of individual initiative, aided by the work of technical journals and metallurgical societies. There still remains a field for profitable discussion, and it is my intention to deal with some inconsistencies of expression common to a number of writers on the subject; and also to draw attention to the false impressions created by a statement which may, possibly, be only unintentionally misleading. I also take the opportunity of tracing the source of both metallurgical and economic result; and to question the desirability of the methods usually employed in arriving at a final statement. In the first place, I wish to deal with the question of extraction. This term may mean anything or nothing, and it is often used to mislead. In a report of a mining engineer as to the result of operations subsequent to the remodeling of a treatment plant prominence was given to the statement that the extraction had amounted to 91 per cent. On examination it was found that only a small percentage of the so-called extraction was calculated on actual bullion return, a proportion being figured from the gold left in the zinc boxes, and not recovered. In addition to this, a proportion of the extraction was said to be due to gold in concentrate. As there was no concentrating apparatus on the property and as concentration did not form a part of the scheme of treatment the matter was investigated, with the result that the concentrate, of lower gold content that the original ore, was found to be the result of an inefficient pumping system which failed to provide for the whole of the battery product delivered to it. The balance was stacked and, although itself of no marketable value, the gold content was allowed to form a basis of extraction figures.

Jan 7, 1914

By R. S. Shoemaker, F. W. McQuiston

MAGMA COPPER COMPANY San Manuel Division The San Manuel Division of Magma Copper Company is located about 40 miles north of Tucson. Tons of ore milled in 1973 .were approximately 19 million at a rate of 63,000 tons per day. From this, about 42,600 tons of copper concentrate was produced as saying approximately 1.070 MoS2 and 28.5% Cu. As with many copper ores, the San Manuel ore contains a small amount of gold, but in this particular case, much of the gold follows the molybdenite. Separation of the molybdenite from the bulk sulfide concentrate by flotation produces a moly concentrate containing 9170 MoS2, just under 1.070 Cu, and 0.44 oz Au per ton. Cyanidation of this material for gold recovery is the only practice of its kind known to the authors of this Monograph. After thickening, the final moly concentrate is filtered for subsequent repulping with cyanide and lime. Gold dissolution takes place in three agitators in series with the pulp from the agitators being filtered in two stages in disc filters. Between filtration stages, the cake is repulped with barren solution. Filtrate from both filters is the pregnant solution. The Merrill-Crowe recovery unit is comprised of two solution tanks and the usual clarifying filter, vacuum tower, zinc dust feeder and Merrill precipitate press. Because of the presence of finely divided sooty chalcocite in the molybdenum concentrate, the cyanide consumption of 55 pounds per ton is extremely high. A compensating factor, however, is the low copper, moly concentrate produced. Precipitation of the gold from the highly copper-contaminated solution requires 0.56 pounds of zinc dust and 0.28 pounds of lead acetate per ton, high figures when compared to normal cyanidation practice. The Merrill- Crowe precipitate assays approximately 28.5% Cu, 8% Zn, 156 oz Au and 197 oz Ag per ton. The San Manuel cyanidation plant is an outstanding and innovative development.

Jan 1, 1975

By Henry Rogatz

Oil.—During the year 1938, there were 434 oil wells drilled in the Texas Panhandle, increasing the daily initial production by 192,706 bbl. —that is, 229 fewer oil wells drilled than in the previous year, with a decrease in total daily initial production of 129,626 bbl. The total daily potential of the field on Dec. 1, 1938, as determined by the Texas Railroad Commission, was 1,250,645 bbl., an increase of 210,663 bbl. over the previous year. On Dec. 1, 1938, the daily allowable of 82,466 bbl. was assigned to the field to be produced from 3931 wells. The total amount of oil produced for the year was 23,227,170 bbl. The total proven productive area includes 148,298 acres. This is 30,248 acres more than for last year, and represents a more accurate calculation of the areas and not new discoveries. Gas.—There were 103 gas wells drilled during 1938, having a combined open flow of 3,166,300,000 cu. ft.; that is, 65 less than the number of wells drilled in 1937, with a decrease in the open flow of 3,144,488 cu. ft. per day. Pipe-line Gas.—The pipe-line companies withdrew 230,307,854,000 cu. ft. of gas (a daily average of 630,980,000 cu. ft.). The total withdrawals by pipe line decreased 5,624,481,000 ft. from that of 1937. Natural Gaso1ine.—Throughout the greater part of the year, 46 gasoline-extraction plants processed 1,376,186,000 cu. ft. per day, a total of 502,308,010,000 cu. ft. for the year. This gas yielded about 275,875,000 gal. of natural gasoline. The total daily capacity of all the plants is 2,519,500,000 cu. ft. During the latter part of 1938, one of these plants was shut down, leaving 45 plants operating at the close of the year. Carbon Black.—Thirty carbon-black plants operated during 1938, burning 266,881,000,000 cu. ft., or a daily amount of 731,180,000 cu. ft. This produced approximately 400,000,000 lb. of carbon black. During the year one plant was dismantled and two plants were shut down.

Jan 1, 1939

By Henry Rogatz

Oil.—During the year 1938, there were 434 oil wells drilled in the Texas Panhandle, increasing the daily initial production by 192,706 bbl. —that is, 229 fewer oil wells drilled than in the previous year, with a decrease in total daily initial production of 129,626 bbl. The total daily potential of the field on Dec. 1, 1938, as determined by the Texas Railroad Commission, was 1,250,645 bbl., an increase of 210,663 bbl. over the previous year. On Dec. 1, 1938, the daily allowable of 82,466 bbl. was assigned to the field to be produced from 3931 wells. The total amount of oil produced for the year was 23,227,170 bbl. The total proven productive area includes 148,298 acres. This is 30,248 acres more than for last year, and represents a more accurate calculation of the areas and not new discoveries. Gas.—There were 103 gas wells drilled during 1938, having a combined open flow of 3,166,300,000 cu. ft.; that is, 65 less than the number of wells drilled in 1937, with a decrease in the open flow of 3,144,488 cu. ft. per day. Pipe-line Gas.—The pipe-line companies withdrew 230,307,854,000 cu. ft. of gas (a daily average of 630,980,000 cu. ft.). The total withdrawals by pipe line decreased 5,624,481,000 ft. from that of 1937. Natural Gaso1ine.—Throughout the greater part of the year, 46 gasoline-extraction plants processed 1,376,186,000 cu. ft. per day, a total of 502,308,010,000 cu. ft. for the year. This gas yielded about 275,875,000 gal. of natural gasoline. The total daily capacity of all the plants is 2,519,500,000 cu. ft. During the latter part of 1938, one of these plants was shut down, leaving 45 plants operating at the close of the year. Carbon Black.—Thirty carbon-black plants operated during 1938, burning 266,881,000,000 cu. ft., or a daily amount of 731,180,000 cu. ft. This produced approximately 400,000,000 lb. of carbon black. During the year one plant was dismantled and two plants were shut down.

Jan 1, 1939

By F. A. Kjellin

The problem of smelting steel by electricity attracted years ago the attention of inventors, and as early as 1879 C. W. Siemens constructed his first furnace for the smelting of metals, especially steel. His furnace was of the arc type in which the voltaic arc was formed between a carbon electrode and the metallic content of a crucible, the length of the arc being regulated by an electromagnetic device. This electric furnace, as well as others of similar construction, has the inconvenience that the source of the heat—the voltaic arc—possesses a temperature of 3,700' C., which is much

Jan 1, 1904

By John Tyssowski

In 1925, Harry Howard Stout, then metallurgist for Phelps Dodge Corporation, while investigating the cleaning of cathode copper by various gases at elevated temperatures below the melting point of the metal, observed in the laboratory that particles of pure copper heated in a closed tube filled with hydrogen seemingly "stuck together." By further investigation he found that there was actual crystal growth across the boundaries of the particles of pure metal; in other words, there was a complete new crystal realignment and growth throughout the newly formed copper mass. It was coalescence, not adhesion; the several particles had become one unit. From this discovery has been developed the coalescence process, whereby copper of cathode purity is squirted out in semifabricated form from an extrusion press, by the application of about 3000 tons pressure on a 10-in. piston. Stout decided that cathode copper produced by electrolytic deposition was the logical source of the pure copper required for the coalescence process, but as there was no way of reducing the ordinary tough commercial cathodes to the small particles required he was confronted by a serious problem at the outset. Under his direction, this problem was solved by William H. Osborn and Harry Howard Stout, Jr. They developed the process and technique for producing cathode copper in brittle, friable form, and to them must be given the greater part of the credit for this phase of the development program as well as for that relating to the gas cleaning of the cathode particles. Concurrently, the three metallurgists worked on the problem of effecting a complete union of the cathode particles. Adequate washing was all that was needed to free the particles from electrolyte solution and slimes. A press was designed to produce briquettes of the proper porosity and density, and a method was devised of removing surface oxidation from the particles of cathode, by treatment in an atmosphere of deoxidizing gas at an elevated temperature. The temperature was determined at which the surface cleansing and preheating could be done in one operation, and for this a charging and preheating furnace in which there is maintained a positive pressure of deoxidizing gas atmosphere was designed. And finally, a method of feeding the heated briquettes of deoxidized cathode copper into an extrusion press without contamination from the air was evolved. For the final stage, a press was required because not only heat but pressure was required to obtain complete growth of the new crystals between the cathode particles as well as the elimination of all voids or non-coalesced areas. All essential stages of the process are protected by patents or patent applications in the United States and principal foreign countries, and the copper is produced on a commercial scale.

Jan 1, 1941

By John Tyssowski

In 1925, Harry Howard Stout, then metallurgist for Phelps Dodge Corporation, while investigating the cleaning of cathode copper by various gases at elevated temperatures below the melting point of the metal, observed in the laboratory that particles of pure copper heated in a closed tube filled with hydrogen seemingly "stuck together." By further investigation he found that there was actual crystal growth across the boundaries of the particles of pure metal; in other words, there was a complete new crystal realignment and growth throughout the newly formed copper mass. It was coalescence, not adhesion; the several particles had become one unit. From this discovery has been developed the coalescence process, whereby copper of cathode purity is squirted out in semifabricated form from an extrusion press, by the application of about 3000 tons pressure on a 10-in. piston. Stout decided that cathode copper produced by electrolytic deposition was the logical source of the pure copper required for the coalescence process, but as there was no way of reducing the ordinary tough commercial cathodes to the small particles required he was confronted by a serious problem at the outset. Under his direction, this problem was solved by William H. Osborn and Harry Howard Stout, Jr. They developed the process and technique for producing cathode copper in brittle, friable form, and to them must be given the greater part of the credit for this phase of the development program as well as for that relating to the gas cleaning of the cathode particles. Concurrently, the three metallurgists worked on the problem of effecting a complete union of the cathode particles. Adequate washing was all that was needed to free the particles from electrolyte solution and slimes. A press was designed to produce briquettes of the proper porosity and density, and a method was devised of removing surface oxidation from the particles of cathode, by treatment in an atmosphere of deoxidizing gas at an elevated temperature. The temperature was determined at which the surface cleansing and preheating could be done in one operation, and for this a charging and preheating furnace in which there is maintained a positive pressure of deoxidizing gas atmosphere was designed. And finally, a method of feeding the heated briquettes of deoxidized cathode copper into an extrusion press without contamination from the air was evolved. For the final stage, a press was required because not only heat but pressure was required to obtain complete growth of the new crystals between the cathode particles as well as the elimination of all voids or non-coalesced areas. All essential stages of the process are protected by patents or patent applications in the United States and principal foreign countries, and the copper is produced on a commercial scale.

Jan 1, 1941