Search Documents

By V. Steve Reed, Ed L. Reed

The in situ leach mining process generates a waste stream that is high in sulfates, total dissolved solids, and radium 226. During the mining phase, the volume of the waste stream is relatively low and consists primarily of the bleed stream. During the restoration phase, larger volumes of waste water are generated. These waste streams require environrnentally sound disposal. The low net evaporation rate in the Coastal Bend area precludes pond evaporation as a feasible disposal alternative. Reverse osmosis is a practical method of reducing the volume of the waste water handled, but the concentrated waste stream from the reverse osmosis unit must be disposed properly. Deep well injection into highly saline reservoirs is considered a sound method of disposing of the liquid waste generated by in situ mining in the Gulf Coast uranium district. Thirteen injection wells have been permitted to serve the disposal needs of the leach mining industry in Texas. Of these 13, 11 have actually been drilled. Seven applications are pending. The injection zones for the permitted wells range from depths of 3050 to 6200 feet. Pressure limitations imposed on these wells range from 500 psi to 1350 psi. The following criteria are used to determine the desirability of a disposal well site: 1. A minimal number of nearby, improperly plugged borings which penetrate the disposal zone; 2. Minimal crustal disturbance; 3. Sufficient salinity of the water contained in the disposal zone; 4. Protection of oil and gas producing zones; and 5. Sand of sufficient permeability and areal extent to handle the desired volume without fracturing the reservoir. 1. Improperly plugged borings: During the early part of the century, oil wells, gas wells and test holes were drilled using cable tool equipment, often with a minimum amount of surface casing. Production casing, when it was set, was often partly removed when the holes were abandoned. Thus, wells drilled prior to 1940 frequently have less than 100 feet of surface casing and either no production casing or the upper part of the production casing removed. Additionally, these holes are often plugged only with mud. The close proximity of these holes to an injection well location are a concern in that they can provide an avenue for injection-depth fluids to migrate up the bore hole and jeopardize shallower fresh water reservoirs. Usually, where there are more than 6 or 8 poorly plugged borings in a 2 1/2 mile radius of the well site, it is preferable to examine deeper zones for disposal well potential. The deeper zones are especially attractive where the borings are not in a cluster, which renders monitoring more difficult. Often, even the deeper disposal zones are penetrated by a few improperly plugged borings. When this condition arises, the potential for leakage through the borings can be addressed in the following ways. a. Demonstration that the static head in the boring is higher than the anticipated increase in bottom hole pressure generated at the boring by the disposal well. A 100 psi differential between these two pressures is recommended. The calculated increased pressure at a boring caused by injection should be refined using annual bottom hole pressure measurements in the disposal well. Figure 1 illustrates an injection pressure map which can be overlain on the oil well map to determine the anticipated increase in pressure expected at each oil, gas or abandoned hole. b. Shallow ground water monitoring. A shallow monitor well is drilled next to the boring and both pressure and quality measurements are made periodically in the shallow well. c. Disposal zone monitoring. Recently there has been a tendency for regulators to require disposal depth monitor wells instead of shallow well monitoring. We consider disposal depth monitoring to be a less effective method of monitoring because it provides only indirect evidence of potential problems. Assumptions have to be made for the unplugged borings, such as mud weight, that are not addressed by the disposal zone monitoring program. There is little improvement with this system to that discussed in "a" above. A shallow zone monitoring program, however, yields direct evidence of a developing problem with an unplugged boring. Leakage by the boring will be detected quickly by an abnormal increase in pressure in the shallow well. Quality monitoring will detect upward migration of poor quality fluids. The pressure data provide an early warning of impending leakage; the quality monitoring will detect actual fluid migration.

Jan 1, 1980

By R. A. Oriani

The partial molal volume of hydrogen is one of the parameters that describe the elastic interaction between the solute and the stress fields about inclusions, dislocations, and cracks. As such the partial molal volume is probably of importance in the elucidation of phenomena such as hydrogen embrittlement and hydrogen yield point. A knowledge of this quantity would also be helpful in thinking about the state of dissolved hydrogen in iron. However, because of the very low lattice solubility of hydrogen in iron the usual ways of determining the lattice expansion are not practicable. It is therefore of interest to apply the thermodynamics of stressed bodies to two sets of measurements of the effect of elastic stress upon the permeability of hydrogen in order to deduce a value of the partial molal volume, VH, of hydrogen dissolved in a iron. Beck ..' and previously de Kazinczy, observed that a uniaxial tensile stress increases the permeability of hydrogen in iron and in various steels. Beck et 01. employed Armco iron and A.I.S.I. 4340 steel, whereas de Kazinczy used a steel the composition of which was 0.13 C, 0.23 Si, 0.46 Mn, 0.006 P, and 0.038 S. Upon releasing the stress the permeability increment disappeared if the stress was below the elastic limit. Both investigators employed cathodic charging to introduce the hydrogen. de Kazinczy measured the permeation through a thin-walled tube by collecting the gas, whereas Beck et al. measured the permeation through sheets of various thicknesses by a very sensitive electrochemical technique. Both investigators measured the steady-state permeation at constant rate of hydrogen ion discharge, and Beck measured in addition the hydrogen diffusivity by a time-lag technique which is independent of the boundary conditions. Beck et al. and de Kazinczy found a linear relationship between log (J,/Jo) and the stress, where Ju/Jo is the ratio of the flux of hydrogen when the metal is under uniaxial tensile stress, a, to the flux under zero stress, for the same temperature and charging current. Beck et al. found in addition that the diffusivity of hydrogen is not changed by stress. Both investigators concluded that the observed change in permeability is due to an increase in hydrogen concentration, and furthermore that the increase in concentration is due directly to the thermodynamic effect of stress upon concentration. Accepting this assessment of the situation for reasons given below, one may use the equation3j4 in order to evaluate I/H, the partial molal volume of hydrogen. This equation is valid for the domain of a/E «¦ 1 (where E is the Young's modulus) and under the assumption that hydrogen expands the lattice isotrop-ically. From the data of Beck el al, one calculates V7H - 2.0 cu cm per g-atom, and from those of de Kazinczy one obtains 1.8 cu cm per g-atom. That the increase of concentration with stress is indeed of thermodynamic origin is attested to by the facts that the experimental results conform to the thermodynamic relation, Eq. [I], and that the results are the same whether a pure iron1 or each of two different steels172 is used. Neither of these facts wou1.d necessarily be expected if the effect of stress were, rather, to increase the ratio kn/k, of the kinetic factors of the following competing reactions: H(ads) — H (dissolved) Such a change of kinetics at the surface could be an alternative explanation of the effect of stress on the permeability. Although this writer does not deem this explanation to be the correct one for the reasons given above, it must be admitted that unambiguous proof that the phenomenon has a thermodynamic origin does not yet exist. Two kinds of experiments may be suggested. One is to plate a variety of metals on the input surface of the steel and repeat the stress experiment at a variety of hydrogen charging currents. The other is to employ somewhat thicker specimens in order to be able to apply uniaxial compressive stress. Eq. [I] shows that ln(c,/c,) depends on the sign of the stress, but it is difficult to see a physical basis for which k2/kl would depend on the sign of a. The present value of V^ in a iron agrees with phragmen's5 estimate, which he based on comparisons with the lattice expansion by hydrogen of titanium, zir-

Jan 1, 1967

By S. J. Salat, E. E. Burton

The new Inspiration copper smelter, which introduced unique technological innovations to the copper industry, required a plant material handling system to match. The system has been designed to convey such diverse bulk materials as copper concentrates, copper precipitates, lime, limestone, silica, flue dust, and revert materials. The moisture content in the materials varies from bone dry to a maximum of 25%. Since the summer of I974 when the smelter went into operation, the material handling system ha provided satisfactory and dependable services.

Jan 1, 1981

By A. U. Seybolt

The solubility of oxygen in a iron has been determined in the range between 700° and 900°C. The solubility is a function of temperature and varies from about 0.008 pct oxygen at 700°C to atureandabout 0.03 pct at 900°C. The heat of solution is approximately +15,500 cal per mol. AS pointed out in a recent paper by Kitchener et al.,1 there has been a lack of agreement among many investigators even as to the order of magnitude of the solid solubility of oxygen in the various forms of iron. This lack of agreement is attributable in large part to the difficulties in the determination of a small oxygen solubility; but because the problem has remained so long unsettled, it also indicates a lack of interest which is rather surprising when the demonstrated importance of small amounts of soluble nonmetallic impurities in iron is considered. The work of Kitchener et al. apparently leaves the solubility of oxygen in iron in a satisfactory state, but no attempt was made to investigate the solubility in a iron. The solubility of oxygen in a iron is actually of greater interest, since it is in this form that iron and mild steels are employed ordinarily. That the effect of oxygen in iron is of more than theoretical interest has been well established by Fast,' and more recently by Rees and Hopkins," who demonstrated that oxygen in the range between 0.0008 and 0.27 wt pct has a pronounced effect upon the mechanical properties. Previous Work and Methods Used To report in detail the literature relating to the solubility of oxygen in a iron would require an inordinate amount of space. For those interested in reviewing this work, a bibliography4-13 of the more significant papers is appended. In general, two methods of studying this problem have been used. One is the gas-metal equilibrium method where the H2O-H2-Fe or the CO2-CO-Fe equilibria have been used. The other is the more direct approach of the oxidation of thin strips of pure iron by packing in mill scale or by air or gaseous oxygen at some desired temperature. In this method oxygen is allowed to oxidize the surface and then to diffuse inward until saturation is obtained. In the gas-metal equilibrium method the oxygen dissolved in solid iron at a given temperature is proportional to the ratio of the water vapor-hydrogen pressures or the CO2-CO pressures over the sample for small ratio values. If the ratio becomes higher than a critical value, then an oxide phase makes its appearance (the solution becomes supersaturated). In principle, it is possible to use a series of H2O/H2 or CO2/CO ratios and to find by analysis the corresponding amounts of oxygen in solid solution at constant temperature. At the point where a very small increase in the gas ratio (increase in oxidizing powder) produces a large increase in oxygen content, the solid solubility limit is reached. Alternately, if the critical ratio is known, it is possible to use the procedure of Kitchener et al.1 and to use a ratio which is near but below the critical one. The solubility corresponding to this lower ratio will not be the saturation solubility at the temperature employed, but the saturation solubility can be calculated by multiplying the measured solubility by the critical ratio over the ratio used. However, in the case where oxygen gas is the oxidizing medium, the saturation solubility is not a function of pressure, providing the pressure exceeds the dissociation pressure of FeO in equilibrium with iron. This is 1.2x10-16 mm at 800 °C, according to Dushman." As pointed out by Darken17 in discussing the FeO phase diagram, most of the possible errors tend to yield high values of oxygen solubility. For example, one circumstance which evidently caused the reporting of many high values was the use of finely divided or powdered iron in the gas equilibrium method. Because of the large surface area of such a sample, and the likelihood of some surface contamination if only by exposure to air, the results tended to be high. The direct oxidation method which was used in this work has the advantage in that it is simple and direct, but it suffers from one disadvantage: equilibrium can only be approached from the low oxygen side. The important factors to be kept under control are the following: 1—use of high purity iron to avoid internal oxidation (oxidation of readily

Jan 1, 1955

By S. Oglesby, A. L. Thomas

Until recently, probably the best means of sampling airborne dusts has been the impinger method. Dust-laden air is drawn into a sampling tube, and the particulate matters separated from the air and collected in the liquid in the impinger. A sample of the suspension is prepared on a slide and counted through a projection microscope. This method is simple and reliable, but it does suffer drawbacks. Since the collected particles must be counted visually, results of the dust count are not immediately available at the time the sample is taken. This seriously impedes studying the effectiveness of dust inhibitors, such as water sprays, or making adjustments in equipment. Greatest disadvantage of all, however, is the tedious task of counting particles in the sample. With the growing desirability of taking more samples, the effort involved in making these counts is a real factor in the cost of dust control. Finally, it is generally recognized that impinger dust counts can be related to health hazard only for specific kinds of dust and under similar conditions. This is because the rather complex mechanism of dust damage depends so much on size distribution of the dust. Counts determined by impinger samples cover a limited size range that does not necessarily corre-

Jan 1, 1960

By David A. Thomas, David N. French

The lrnrdness of WC crystals has been measured with the Knoop indenter at loads of 100 and 500 g on the (0001) and (1070) planes. The hardness as tneasitred on the basal plane is 2400 kg per sq mm and shows little anisotropy. The hardness on the prism plane, however, shows a marked orientation dependence, with a low value of 1000 kg -per sq mm when the long axis of the Knoop indenter is oriented parallel to the c axis and a high value of 2400 kg per sq mm when the indenter is perpendicular to the c axis. Slip lines (Ire observed surrounding the microhardness indentations and they show slip on (1010) planes, probably in [0001] and (1120) directions. This slip behavior can be explained by the crystal structure of TVC, which is simple hexagonal with a c/a ralio of 0.976. The hardness anisotropy call be explained by [0001]{1010} and (1130) {10l0] slii) and the resolved shear-stress analysis of Daniels and Dunn. HARDNESS anisotropy is a well-known phenomenon and has been reported for many metals, with both cubic and hexagonal structure.1-6 For hexagonal tungsten carbide, WC, a wide range of hardness values is reported in the literature. For example, Schwarzkopf and Kieffer7 give a hardness of 2400 kg per sq mm and report a value of 2500 kg per sq mm by Hinnüber. Foster and coworkerss give the average Knoop microhardness as 1307 kg per sq mm with a maximum value of 2105 kg per sq mm. Although these values and the structure of WC suggest the likelihood of hardness anisotropy, no such measurements have been made. We first detected a large apparent hardness anisotropy in WC crystals about 75 p large, in over-sintered cemented tungsten carbide. Prominent slip lines also occurred around many indentations. This report presents further observations and interpretations of hardness anisotropy and slip in WC crystals obtained from Kennametal, Inc. Both Knoop and diamond pyramid indenters were used on a Wilson microhardness tester with loads of 100 and 500 g. EXPERIMENTAL RESULTS The carbide crystals tended to be triangular plates parallel to the (0001) basal plane of the hexagonal structure. The side faces were parallel to the ( 1010) prism planes. Specimens were mounted approximately parallel to these two types of faces and metallographically polished. Laue back-reflection X-ray patterns were used to orient the specimens, which werethen ground to within ±1 deg of the (0001) and (1010) planes. The Knoop hardness values measured on the basal plane are plotted in Fig. 1. There is only a small anisotropy, with a hardness range of 2240 to 2510 kg per sq mm. The additional points at angles from 52.5 to 67.5 deg confirm the sharp minimum hardness at 60-deg intervals, consistent with the sixfold hexagonal symmetry. The average hardness of all values obtained on the basal plane is 2400 kg per sq mm. While the basal plane shows only slight anisotropy, the (1010) plane exhibits marked hardness anisotropy, from 1000 to 2400 kg per sq mm. Fig. 2 shows the hardness as a function of the angle between the long axis of the indenter and the hexagonal c axis, the [0001] direction. The minimum and maximum occur when the indenter is oriented parallel and perpendicular to the [0001] direction, respectively. The anisotropy of the prism plane is contrary to that reported for hexagonal zinc and hard- However, the basal-plane anisotropy is similar to these two metals.1'2 To check the accuracy and reproducibility of the measurements, a series of fifteen impressions was made at 100-g load in the same orientation in the same area of the specimen surface. The average for all was 2040 kg per sq mm, with a range of 1950 to 2130 kg per sq mm, giving an accuracy of about ± 5 pct. Thus the slight anisotropy on the basal plane is almost within experimental error. Fig. 3 shows slip lines around the Knoop indentations on the basal plane. The slip traces are in directions of the type (1130). The presence of slip steps on the basal plane indicates that the slip direction lies out of the (0001) plane. Because WC has a c/a ratio of 0.976,' the shortest slip vector is [0001], which suggests slip systems of the type [0001] (1010). Fig. 4 shows slip lines around the Knoop intentations on the (1010) plane. These slip lines are inconsistent with [0001] slip but can be

Jan 1, 1965

By Bernard Rachlin

IN the mineral industry measurement of density or specific gravity of slurries is often necessary or highly desirable. To date the most successful method of measuring the specific gravity of various media is to hand weigh a constant volume sample of the slurry. This method is time-consuming, however, and is intermittent rather than continuous. Most density measuring instruments in use today are variations of three basic systems: air bubble tube systems, radioactive methods, and displacer systems. The high cost of the radioactive cell, combined with the precision electronic measuring that is required, limits the practical utility of this procedure to a small percentage of critical processes. In the air bubble systems clogging of the bubble tubes with solids has rendered this type of measurement completely ineffectual for many applications. Continuous or intermittent purging of the bubble tubes with air or water to prevent tube clogging has been tried but has not been very successful, especially in the heavy media process. The displacer system, which presents the fewest complications of all the density measuring systems, consists only of a metal immersion unit and a means of weighing it. In the past, settling of the solid in the slurry has caused untrue samples and clogging of the media at the bottom of the chamber. It is also important to dampen excessive flow surges such as those caused by reciprocating pumps. The system described here successfully overcomes these difficulties. Description of the Process System: The process equipment, on which the field tests were run, was a

Jan 1, 1957

By Thomas L. Watson

The occurrence of zircon in pegmatites of acidic composition is recorded by many observers both in this country and abroad, and they form one of the most important geologic modes of occurrence of the minera1. As is well known, commercially the most important American locality for zircon is near Zirconia in Henderson County, North Carolina, where many tons of the mineral have been obtained from a kaolinized pegmatite dike 100 ft. wide and traced for 1 1/2 miles along the direction of strike N. 50" E. Zircon may be developed in pegmatites as inclusions in the principal rock-forming minerals, chiefly quartz and feldspar, and as a separate megascopic constituent in the form of grains and crystals not exceeding, as a rule, 2 in. in size, and usually smaller. In the Henderson County, North Carolina, pegmatite, zircon occurs in prismatic crystals with pyramidal terminations measuring up to 30 mm. in diameter, associated chiefly with the feldspar. In some of the apatite veins of Canada, which are closely allied to pogmatite dikes, zircon is reported in crystals upward of 6 in. in length and 2 in. and more in thickness. Zircon in large masses occurs in Virginia in the well-known pegmatites near Amelia in Amelia County, and near Gouldin in Hanover County. Both localities are in the middle eastern portion of the Piedmont Plateau province, and are separated by a distance of about 40 miles in a northeast-southwest direction. The rocks of both areas, including the pegmatite bodies, are in an advanced stage of decay, and the hard and moderately fresh rocks are concealed beneath a cover of variable thickness of rock decay derived by the normal processes of weathering. Exposures, there-

Jan 1, 1917

By E. H. Bronson

PROPERTY of Malartic Gold Fields Ltd. is situa-ated in the great clay belt in the northern part of the Province of Quebec. This belt represents the floor of the glacial lake Barlow-Ojibway. The clay blanket has a gently rolling, almost flat surface, with here and there projecting knobs and ridges that outline the large irregularities of the surface on which the clay was deposited. At irregular intervals glacial eskers dominate the landscape. The ore-bearing country rock is covered by strata of clay, sand, and silt to a depth varying to 40 ft. There are serious structural problems when it is necessary to place loads of unequal intensities on this surface to support buildings and machinery for a modern mining plant. Earlier mining companies and their engineers paid little attention to the science of soil mechanics, partly because they believed it unnecessary and partly because they knew little of the subject. The results are evident in some of the tottering structures in older camps. Careful analysis of soil problems is well worth-while, since cost of foundations may vary from 20 to 50 pct of the final cost of a structure. Low operating and maintenance costs can be achieved only in this way. If it is definitely established that a plant will be in operation for only a few months, this limited time factor will probably influence the design of the foundation, and rightly so. If sensitive and complickted equipment is to be mounted on these foundations and the plant is to operate for several years, there should be a thorough study of foundations and a very careful design. A familiar problem is presented by the difficulty of operating a permanent plant originally designed for a few months' work. The engineer must beware of these hazards and disassociate himself from them if he cannot prevail on the promoter to spend the proper amount for a thorough foundation study. Laws of certain provinces and states hold the engineer equally responsible with the contractor for any 'damage that may be caused to building through inadequate study-ignordnce of the facts is no excuse in the eyes of the law. Types of Soil: The engineer should be familiar with such terms as silt, clay, peat, and varved clay, as well as perpafrost, especially if he is to work in the far northern reaches of the country. He should also be familiar with soil attributes such as porosity, texture, consistency, permeability, compressibility, consolidation, and shearing resistance. The design of any foundation requires an accurate knowledge of the physical properties and location of the soils involved. Older textbooks on the subject outline various empirical methods to determine the carrying power of soil. Tables are given in reference books. The modern ehgineer should be wary of these modes of thinking. He should analyze his problem carefully, calculate to what depth of soil the loads may be transmitted, and then check the bearing value of all soils to that or greater depths. If the strata are water-carrying, he must determine the possibility of this water being accidentally re-

Jan 1, 1958

By R. W. Fountain, W. D. Forgeng, G. M. Faulring

Precipitation of the phase Co3Ti (Cu3Au type) from a Co-5 pct Ti a11oy has been investigated using single-crystal X-ray diffraction techniques. Oscillation and transmission Laue patterns of specimens aged for short-time periods at 600" C indicate the formation of titanium-rich and titanium-poor zones coherent with the {100} matrix planes. Longer aging times at 600° C establish that the equilibrium phase also forms on the {100} matrix planes as platelets. These observations are corroborated by electron metallography; electron diffraction studies show the phase Co3Ti to be ordered. A probable sequence of the precipitation reaction is discussed. A previous publication by two of the present authors reported on the phase relations and precipitation in Co-Ti alloys containing up to 30 pct Ti.1 The results of this investigation established the existence of a new face-centered cubic inter metallic phase, ranging in composition from about 17.0 to 21.7 pct Ti at temperatures below 1000° C The decomposition of the fcc supersaturated solid solution was studied employing hardness and electrical resistivity measurements. The changes in hardness upon precipitation in alloys containing 3, 6, and 9 pct* Ti were found to be associated with an initial increase in hardness followed by a plateau and then a second, more pronounced hardness increase. Investigation of this behavior by electrical resistivity measurements suggested that two different kinetic processes were involved, which, when interpreted in terms of the kinetic relation,2-4 indicated that initial precipitation was in the form of thin plates. On continued aging, the plates impinged during the growth process. The general features of these findings have been confirmed by Bibring and Manenc,5 while, in addition, they report the phase to be ordered. The present investigation was undertaken to provide more definite information on the structural relationships between the precipitate and the matrix. EXPERIMENTAL PROCEDURE Single crystals of a (20-5 pct Ti alloy were prepared from the melt employing the Bridgman technique. Poly crystalline rod, 1/2 in. in diam, prepared from vacuum-melted material, was machined to 3/8- in. diam to remove any surface contamination that may have resulted from hot-working. The crystals were grown under a purified hydrogen atmosphere in high-purity alumina crucibles heated by induction. Considerable difficulty was encountered in attempting to grow monocrystals because of the high melting point of the alloy and the high solute concentration. However, one crystal about 6 in. long was obtained which was essentially a single crystal except for one or two very small grains around the periphery. The as-grown crystal was solution heat-treated for 24 hr at 1200°Cin a purified argon atmosphere and water-quenched. One-quarter-in. slices were taken from each end of the solution heat-treated crystal for chemical analyses, and the remainder of the crystal was mounted and oriented by the back reflection Laue Method. The chemical analysis of the crystal was as follows: Pct Ti Pct 0 Pct C Pct N Pct H Pet CO 5.29 0.08 0.004 0.002 0.0003 Balance By proper tilting of the crystal, it was possible to obtain slices 1/32 in. thick of [loo] and [110] orientation. The solution heat-treated crystal slices were sealed in silica capsules for the aging treatments, with titanium sponge placed at one end of the capsule to act as a getter. All slices were water-quenched from the aging temperatures, the capsules being broken under the water to ensure a rapid quench. Thinning of the slices for transmission X-ray studies was accomplished by a combination of mechanical and electrolytic techniques, the final thickness being about 0.1 mm. Laue patterns of the solution heat-treated crystal indicated that no strain was introduced by the thinning technique. ELECTRON METALLOGRAPHY After X-ray examination, the structural changes attending the precipitation were followed by examination of direct carbon replicas of polished and etched surfaces of the single-crystal slices and extracted phases. The earliest indication of significant structural change was observed after aging at 600°C The structure of a heavily etched, solution-treated crystal is shown in Fig. l(a). Aside from the etch pit pattern, no regularity of background structure is observed. On the other hand, in the background of the specimen heated for 500 hr at 600°C, the etching pattern shows a directionality indicating the influence of minute precipitate particles, Fig. l(b). On electrolytic dissolution of this specimen in 10 pct HC1 in alcohol, a large volume of very small, flattened cubes

Jan 1, 1962

By W. D. Von Gonten, R. L. Whiting

Regression analysis was used to correlate the physical properties of 478 sandstone and 90 carbonate core samples. Porosity, permeability, electrical formation resistivity factor, capillary pressure and the sonic velocity of the shear and compressional waves were measured. Prediction equations for porosity, permeability and electrical formation resistivity factor were found which should be useful in understanding the relationships between the physical properties of porous media in formation evaluation. INTRODUCTION The physical properties of porous media are important to the petroleum engineer and geologist. To evaluate fully the potential and behavior of a subsurface formation such as a petroleum reservoir, certain physical properties of the porous medium must be known. The problem of accurately determining physical properties of subsurface formations has not been solved because many determinations must be made by indirect measurements and because of the difficulties caused by complex pore structure and presence of clays in most naturally occurring porous media. Due to the difficulty in measuring some of the physical properties of porous media, it would be advantageous to be able to predict a certain physical property of a rock from other physical properties of the rock which could be measured more easily and more accurately. Since most potential reservoir rocks are heterogeneous, relationships between the physical properties are very complex and thus far no satisfactory correlations based on theory or laboratory models have been developed. It appears that empirical relationships obtained by measuring the physical properties of a large number of samples of naturally occurring porous media and applying regression analysis to develop equations for one physical property in terms of other rock properties is the best approach. REVIEW LITERATURE The three physical properties used as dependent variables for correlating purposes were porosity, permeability and formation factor. Since formation factor is more difficult to determine, a brief review of the literature is provided on this property. The first work on determining formation factors was published by Archie1 in 1942. He defined this property of a porous medium as F - Ro/Rw......(1) where Ro is the resistivity of the porous medium when completely saturated with a brine of resistivity Rw. Archie found the best correlation between formation factor and porosity was the following equation, where is the porosity fraction and m is the constant characteristic of the rock. The value of m was 1.3 for unconsolidated sand packs, and ranged from 1.8 to 2.0 for consolidated sandstones. In 1950 Patnode and Wyllie2 and De Witte3 observed that the formation factor as determined by Eq. 1 was valid only when the porous medium contained no conductive solids such as clay or shale. When conductive solids are present the formation factor is also dependent on the resistivity of the saturating fluid. Therefore, in samples containing conductive solids the formation factor decreased as the resistivity of the saturating fluid increased. Because of this. the measured formation factor was called the apparent formation factor and was designated Fa. Patnode and Wyllie proposed the following equation,

By W. R. Purcell

An apparatus is described whereby capillary pressure curves for porous media may be determined by a technique that involves forcing mercury under pressure into the evacuated pores of solids. The data so obtained are compared with capillary pressure curves determined by the porous diaphragm method, and the advantages of the mercury injection method are stated. Based upon a simplified working hypothesis, an equation is derived to show the relationship of the permeability of a porous medium to its porosity and capillary pressure curve, and experimental data are presented to support its validity. A procedure is outlined whereby an estimate of the permeability of drill cuttings may be made with sufficient acuracy to meet most engineering requirements. INTRODUCTION The nature of capillary pressures and the role they play in reservoir behavior have been lucidly discussed by Lev-rett', Hassler, Brunner, and Deah12, and others. As a result of these publications the value of determining capillary pressure curves for cores has come to be generally recognized within the oil industry. While considerable attention has been directed toward the subject in an effort to provide a reliable method of estimating percentages of connate water, it has been recognized that capillary pressure data may prove of value in other equally important applications. This paper describes a method and procedure for determining capillary pressure curves for porous media wherein mercury is forced under pressure into the evacuated pores of the solids. The pressure-volume relationships ob- tained are reasonably similar to capillary pressure curves determined by the generally accepted porous diaphragm method. The advantages of the method lie in the rapidity with which the experimental data can be obtained and in the fact that small, irregularly shaped samples, e.g., drill cuttings, can be handled in the same manner as larger pieces of regular shape such as cores or permeability plugs. Based upon a simplified working hypothesis, a theoretical equation will be derived which relates the capillary pressure curve to the porosity and permeability of a porous solid, and experimental data will be presented to support its validity. This relationship aplied to capillary pressure data obtained for drill cuttings by the procedure described provides a means for predicting the permeability of drill cuttings. METHODS FOR DETERMINING CAPILLARY PRESSURES Several techniques have so far been employed in determining capillary pressure curves and these fall into two principal categories: (1) Liquid is removed from, or imbibed by, the core through the medium of a high displacement pressure porous diaphragm (2) Liquid is removed from the core which is subjected to high centrifugal forces in a centrifuge4,'. There are? however, certain limitations inherent in both methods. The greatest capillary pressure which can be observed by method (I), above, is determined by the maximum displacement pressure procurable in a permeable diaphragm which at the present time appears to be less than 100 psi. An even more serious limitation of the diaphragm method is imposed hy the fact that several days may be required to reach saturation equilibrium at a given pressure; hence, the time re- quired to obtain a well-defined curve may be measured in terms of weeks. Furthermore, to date, no suitable technique for handling relatively small, irregularly shaped pieces of rock, such as drill cuttings, has been reported and, therefore, measurements must be made, in general, on cores, or portions thereof. The centrifuge method offers the distinct advantage over the porous diaphragm method of arriving at saturation equilibrium in a relatively short time by virtue of the elimination of the transfer medium for the liquid. The calculation of capillary pressures from centrifuge speeds is somewhat tediousa, however, and the equipment required is fairly elaborate. While there exists the possibility that this method might be adaptable to the determination of the capillary pressures of cuttings, this particular ramification has not been investigated, as far as is known. In view of the limitations of the two principal methods for determining capillary pressures, the apparatus described in the following sections has been devised in order that difficulties previously encountered might be circumvented. MERCURY INJECTION METHOD FOR DETERMINING CAPILLARY PRESSURES Theory The methods described above for determining capillary pressures are characterized by the fact that one of the fluids present within the pore spaces of the solid is a liquid which "wets" the solid, i.e., the contact angle which the liquid forms against the solid is less than 90" as measured through that phase. For these "wetting" liquids the action of surface forces is such that the fluid spontaneously fills the voids within the solid. These forces likewise oppose the withdrawal of the fluid from the pores of the solid.

Jan 1, 1949

By W. R. Purcell

An apparatus is described whereby capillary pressure curves for porous media may be determined by a technique that involves forcing mercury under pressure into the evacuated pores of solids. The data so obtained are compared with capillary pressure curves determined by the porous diaphragm method, and the advantages of the mercury injection method are stated. Based upon a simplified working hypothesis, an equation is derived to show the relationship of the permeability of a porous medium to its porosity and capillary pressure curve, and experimental data are presented to support its validity. A procedure is outlined whereby an estimate of the permeability of drill cuttings may be made with sufficient acuracy to meet most engineering requirements. INTRODUCTION The nature of capillary pressures and the role they play in reservoir behavior have been lucidly discussed by Lev-rett', Hassler, Brunner, and Deah12, and others. As a result of these publications the value of determining capillary pressure curves for cores has come to be generally recognized within the oil industry. While considerable attention has been directed toward the subject in an effort to provide a reliable method of estimating percentages of connate water, it has been recognized that capillary pressure data may prove of value in other equally important applications. This paper describes a method and procedure for determining capillary pressure curves for porous media wherein mercury is forced under pressure into the evacuated pores of the solids. The pressure-volume relationships ob- tained are reasonably similar to capillary pressure curves determined by the generally accepted porous diaphragm method. The advantages of the method lie in the rapidity with which the experimental data can be obtained and in the fact that small, irregularly shaped samples, e.g., drill cuttings, can be handled in the same manner as larger pieces of regular shape such as cores or permeability plugs. Based upon a simplified working hypothesis, a theoretical equation will be derived which relates the capillary pressure curve to the porosity and permeability of a porous solid, and experimental data will be presented to support its validity. This relationship aplied to capillary pressure data obtained for drill cuttings by the procedure described provides a means for predicting the permeability of drill cuttings. METHODS FOR DETERMINING CAPILLARY PRESSURES Several techniques have so far been employed in determining capillary pressure curves and these fall into two principal categories: (1) Liquid is removed from, or imbibed by, the core through the medium of a high displacement pressure porous diaphragm (2) Liquid is removed from the core which is subjected to high centrifugal forces in a centrifuge4,'. There are? however, certain limitations inherent in both methods. The greatest capillary pressure which can be observed by method (I), above, is determined by the maximum displacement pressure procurable in a permeable diaphragm which at the present time appears to be less than 100 psi. An even more serious limitation of the diaphragm method is imposed hy the fact that several days may be required to reach saturation equilibrium at a given pressure; hence, the time re- quired to obtain a well-defined curve may be measured in terms of weeks. Furthermore, to date, no suitable technique for handling relatively small, irregularly shaped pieces of rock, such as drill cuttings, has been reported and, therefore, measurements must be made, in general, on cores, or portions thereof. The centrifuge method offers the distinct advantage over the porous diaphragm method of arriving at saturation equilibrium in a relatively short time by virtue of the elimination of the transfer medium for the liquid. The calculation of capillary pressures from centrifuge speeds is somewhat tediousa, however, and the equipment required is fairly elaborate. While there exists the possibility that this method might be adaptable to the determination of the capillary pressures of cuttings, this particular ramification has not been investigated, as far as is known. In view of the limitations of the two principal methods for determining capillary pressures, the apparatus described in the following sections has been devised in order that difficulties previously encountered might be circumvented. MERCURY INJECTION METHOD FOR DETERMINING CAPILLARY PRESSURES Theory The methods described above for determining capillary pressures are characterized by the fact that one of the fluids present within the pore spaces of the solid is a liquid which "wets" the solid, i.e., the contact angle which the liquid forms against the solid is less than 90" as measured through that phase. For these "wetting" liquids the action of surface forces is such that the fluid spontaneously fills the voids within the solid. These forces likewise oppose the withdrawal of the fluid from the pores of the solid.

Jan 1, 1949

By G. H. Wilson

INTRODUCED in 1946 to serve a need in power-plant operation, closed-circuit TV has been used by well over 200 organizations in approximately 25 different industries. Known as industrial television, or simply ITV, it can be described as a private system wherein the television signal is restricted in distribution, usually by confinement within coaxial cable that directly connects the TV camera to one or several monitors, Figs. 1, 2. The picture is continuous and transmission is instantaneous, permitting an observer to see an operation that may be too distant, too inaccessible, or too dangerous to be viewed directly. Destructive testing or the machining of high explosives can now be conducted hundreds of feet away by personnel who still have close control through the eyes of the TV camera. It is also possible for one man to control operations formerly requiring the co-ordinated efforts of several workers. For example, at a large midwestern cement plant conveyance of limestone from primary crusher to raw mill and loading into five storage bins once necessitated the work of two men, one having little to do but prevent spilling of material by manually moving the tripper on the belt conveyor as occasion required. TV cameras mounted on the tripper now provide bin level indication to the conveyor operator at the crusher position so he is able to control the entire loading operation remotely, Fig. 3. By means of a switch, the picture from either camera is alternately available on a single viewer, or monitor, Fig. 4. Each camera is mounted on the tripper by means of a simple adjustable support and looks down into the bin, which is identified by the number of cross members on the vertical rod. Each associated power unit is located on a platform above the camera, Fig. 5. This centralized control by means of TV often has produced superior results, and in many instances saving in operating costs has been sufficient to write off equipment costs within six months to a year. Where a key portion of a process may be enclosed or otherwise inaccessible, TV again reduces the likelihood of mistakes and permits closer control by making available to the operator valuable information he might otherwise never possess. An example of this can be found at a strip mine where the coal seam lies 50 ft or more below the overburden, which is removed by a large wheel shovel. From his centrally located position the shove1 operator was unable to judge accurately to what extent the wheel buckets engaged the earth. His chief indication of efficiency was the amount of overburden on the belt conveyor as it passed his control point 75 ft from the wheel. Now, two television cameras mounted on the tip of the boom permit the operator to view the wheel from each side and provide him with a close-up view of the buckets so that he can take immediate and continuous advantage of their capacity, quickly compensating for ground irregularities and avoiding obstructions, Fig. 6. While the word television conjures up visions of highly complex and intricate apparatus such as that employed in modern TV studios and transmitting stations, the term industrial television should indicate compact, straightforward equipment. Most present-day ITV systems contain fewer than 25 tubes including camera and picture tubes. The average home television receiver alone requires at least that many tubes. Equipment like that illustrated in Fig. 1 contains only 17 tubes, of which 3 are in the camera. It can operate continuously and dependably, without protection, in any temperature from 0" to 150°F. It consumes less current than a toaster and weighs under 140 lb. Camera and monitor may be separated by 1500 to 2000 ft and by greater distance with additional amplification. This equipment is designed to withstand vibrations up to 21/16 in. and will operate successfully under more severe conditions of vibration and heat when suitable enclosures are provided. Any number of cameras may be switched to a single monitor, and any number of monitors, within reason, used simultaneously. Two types of applications in the mining industry have already been described. A third under serious consideration by several organizations will make use of ITV for remote observation of conveyor transfer points at copper concentrating plants so that evidence of belt breakdown and plugging of transfer chutes can be spotted immediately and costly overflow of material avoided. A television camera will soon be installed to view a trough conveyor near the exit of an iron-ore crusher to indicate clogging of the crusher as evidenced by reduction or absence of material on the

Jan 1, 1955

By E. A. Khopunov, V. I. Revnivtsev

The process of triboelectric separation from the point of view of its potential for selective separation of various mineral particles can be described as "dry flotation." Large scale practical applications of this technique are limited because suitable models which can describe contact charging of mineral particles have not been developed. Among the various concepts a promising one is an attempt to change development in dielectric minerals within the limits of contact phenomenon in semiconductors. Experimental investigations reported in this paper indicate that the charge development is mainly a result of contact electrification of dielectric minerals characterized by "donor" and "acceptor" type energy spectra due to lattice defects.

Jan 1, 1980

By John A. Hosking

The recent activity of numerous foreign mining companies in the once flourishing tin fields in Cornwall, England has resulted in renewed interest in the evaluation of hypothermal tin deposits. These deposits are mainly narrow tabular bodies and are usually steeply dipping. They exhibit thermal zoning the mineralization changing from lead/zinc through copper to tin with depth. The tin zone virtually never exceeds 1,000' in depth and the ore shoots within this zone tend to be erratic and localized. The grade which is presently considered to be economic is about 0.7% Sn. , this means a concentration of about l% cassiterite (the only economic mineral) which, being twice as heavy as the gange, represents only. 5% of the lode volumetrically. Within the lode, only one third may reach this economic grade and values within the shoots can range from 100% cassiterite to zero over a few inches. The enormity of the problem of evaluating such a deposit has not been fully appreciated by the companies involved whose experience has, for the main part, been in larger and more predictable ore bodies. This paper attempts to put these problems into perspective and out- lines the useful applicatations of statistical and computer techniques. It also stresses the need for enlightened interpretation of data by men familiar with the problem and that even in this day and age, educated, intuitive deduction should not yet be relegated to the limbo of alchemy and witchcraft.

Jan 1, 1969

By S. W. Parr

FROM a study of sulfur with reference to its specific combination in coal, published as University of Illinois Bulletin No. 111, 1919, it is now possible to determine the various forms of this constituent with a good degree of accuracy. This fact suggests two questions: (1) Are the same analytic methods applicable to coke? (2) Is there any correlation between the forms of sulfur as it occurs in coal and the residual sulfur found in the finished coke? The answer to the second question might be helpful in answering a still further question as to what chemical route the sulfur travels during the carbonization process. While the special studies along these several lines are by no means complete, a few preliminary statements are herewith presented. They may, at least, prove suggestive of further possibilities from a continuation of research along these lines. There is no reason, chemically, why the analytic methods devised for coal should not apply to coke and a fair amount of experience in connection with such use affords confirmation of this statement. The procedure in the case of coal may be briefly outlined as follows; Combinations of sulfur as sulfate, or sulfides other than FeS2, are readily dissolved without disturbing either the pyrite sulfur or the sulfur that is in organic combination by means of dilute hydrochloric, acid-1 part of concentrated HC1 to 10 parts of water or approximately 3 per cent. acid. Digestion at 60° C. for 24 hr. insures the complete removal of the sulfur thus combined. In freshly mined coal the amount of such sulfur is very small; weathering processes, however, may very materially increase the amount of sulfate present.

Jan 9, 1919

By Paul Billingsley

The Georgetown mining district is located in Deerlodge county, Mont., about 20 miles west of Anaconda. It lies along the divide between the headwaters of Warm Springs creek, draining eastward, and Flint creek, flowing west and north through the Philipsburg valley. The actual divide is formed by Cable mountain, a narrow ridge running north and south, terminating to the south in low hills overlooking Georgetown lake, and to the north in a high, rugged plateau that falls off to the west to the wide valley of Flint creek. On the eastern, or Warm Springs, slope of Cable mountain is the Cable mine, with the Hidden Lake mine a few miles north. On the western slope is the Southern Cross group, with smaller mines, the Twilight, Cincinnati, Red Lion, and Big Bill, at intervals to the northward. The Georgetown mines lie in the hills south of Cable mountain; the Philipsburg mines, of which the Granite Mountain, Bimetallic, Hope, and Trout are the chief, form a separate group to the north, overlooking Flint Creek valley and Philipsburg. (See Fig. 1.) The region ranges in elevation from 5,000 to 9,000 ft. It is, with the exception of the lower valleys, well timbered with small fir and pine, although Cable mountain and the higher summits to the northward rise slightly above timber line. The main valleys have the smooth contours of glaciation, and their mouths are frequently choked with morainal deposits. General Geology. In a very general way the valley of Flint creek coincides in this region with the boundary between the pre-Cambrian slates of western Montana and the folded Palaeozoic rocks of the Rocky Mountain system. The great limestone formations of the Carboniferous and Devonian, lying at flat dips, extend from Anaconda well toward the head of Warm Springs creek, but on the divide the Cambrian appears, closely folded and intruded

Jan 1, 1914

HAVING told you about steel in the previous chapter, it seems to me necessary to speak here of brass for the same reason, for it bears the same relation to copper that steel does to iron. It is the opinion of some concerning both of these that they are true minerals because Pliny in his Natural History calls it aurichalcum and says that it has its own ore; he does not say, however, where it is found, and I have not heard from anyone else that it has been found anywhere, and, surely, if it had been found when he wrote, it would also be found today. Since I have no knowledge other than that gained through my own eyes, I tell you as a certainty that just as steel is iron converted by art into almost another kind of metal, so also brass is copper given a yellow color by art. Surely it was a splendid discovery, for which we must praise the alchemists,* although perhaps whoever discovered it was deceived, thinking that he had made gold from copper. Now, in short, this work requires infinite labor, and is carried out in various places, for instance, in Flanders, Cologne, Paris, and in many other countries, and also in the city of Milan in Italy, where I have seen a

Jan 1, 1942

By Gerald Sherman

IN the southern field of the anthracite region of Pennsylvania, many of the coal seams dip at angles of 40° to 50° from the horizontal. For transportation purposes, "tunnels" are driven across the coal measures and, occasionally, "rock gangways," beside the seams and parallel with them. The use of gangways driven in country rock appears to be increas-ing, as they avoid the maintenance' of long gangways in coal, which eventually are driven to the colliery boundaries, and permit mining from a number of intermediate blocks without interference. The rock consists of slates or sandstones of moderate hardness, which may range into very hard, highly siliceous, fine-grained conglomerates. In this distinctly bedded formation,' the direction of the heading, whether parallel with or across the structure, makes it necessary to distribute the drill holes in a different pattern to break the ground, but does not change loading conditions. In 1932, practically all the mucking was done by hand, and it was the established custom to use four men on two drills for drilling and breaking the ground, and five for loading it, out. A driver and mule was needed in addition, to assemble the rock cars at a siding or branching track in the rear, pending their final disposal. This might occupy the driver's whole time, or if the length of haul were short, he might be able to do other useful work. It was thought possible in 1932 to reduce the cost of driving such headings in rock by mechanical loading, and to investigate this subject a scraper loader was used in a section of tunnel then being driven. Opera-tions while driving 195 ft. of this tunnel using a scraper loader were care-fully observed. Time studies were made of the loading, and records made of the routine of breaking ground, but not in such detail. Tunnels or gangways in the colliery are 7 ft. high above the rails, by 10 ft. wide, which requires a minimum of 8 ft. in height, broken to allow for rails and ties. This cross section is of sufficient size to permit the use of any one of several types of power loaders, but for this demonstration if was found most convenient to use a scraper loader.

Jan 1, 1936