Search Documents

By D. H. Wertz, R. R. Furlong

Dry room equipment at Donora Zinc Works is of the design which prevailed at the time the plant was built in 1915. It consists of 11 adjoining rooms, each being 99 ft long, 11 ft wide, and 7 ft high and having a capacity for 1040 retorts. Heat is supplied by steam coils beneath the slatted wood floor and by warm air ducts at the ceiling. Drying practice is about the same as that generally followed in the industry except that, under normal zinc furnace operations, the maximum drying time is 45 days. During certain seasons of the year the drying process was seriously affected by varying weather conditions which frequently resulted in a scrap loss of 5 to 7 pct. Because of these unfavorable conditions, which caused uneven drying and strains in the retorts, increased retort failures in the zinc furnaces were recorded. Regulation of temperature and humidity under all conditions appeared to be the logical solution of this problem. Controlled drying had been developed for a number of ceramic products and investigation of several such drying processes in this area revealed favorable results. Along with control of drying conditions and the attendant decrease in scrap losses, plant operators also reported a material reduction in drying time. Another factor affecting the decision to proceed with this development was the drastic change in market conditions for retort clay. Curtailment of shipments from the chief source of supply made it necessary to proceed with blending of other available clays, but quality of these clays was questionable for adequate retort life in the 24 hr furnace cycle. Rapid furnace testing of new mixtures was desirable but impossible with the prolonged drying schedule. Therefore development of a controlled drying process for zinc re- torts offered the solution to the problem of rapid testing of retort mixtures. Description of Process and Equipment The freshly extruded retort is cylindrical in shape, 58 in. long, 9 in. id and has 1 1/8 in. side walls. One end is closed and approximately 2 in. thick. The moisture content of this "green" retort is about 17 pct which means a necessary removal of 30 lb of water per retort. Retorts are set on the slatted floor of the dry room with the closed end down. The controlled drying process depends upon the circulation of a large volume of conditioned air at low velocity. To provide for uniform distribu-

Jan 1, 1950

By Thomas M. Drown

The use of bromine as an oxidizing agent, particularly for sul phur, has become very general in analysis, replacing the stronger oxidizing acids. The object of this paper is to describe briefly the experience which we have gained with this reagent in the laboratory of Lafayette College in the oxidation of metallic sulphides. Most of the simple sulphides, as blende, pyrite, etc., when exposed to the combined action of an alkaline hydrate and bromine, and finally to hydrochloric acid, are completely and promptly dissolved. The procedure is as follows: The very finely pulverized mineral is first treated, in a beaker, with a solution of sodium hydrate of a spe cific gravity of 1.25, and heated ; bromine is then cautiously added to supersaturation, and finally hydrochloric acid to acid reaction. If any of the sulphide is not taken up, the same operation may be re peated. It is necessary, however, that the mineral be very finely pulverized. Instead of using the pure bromine, a saturated solu tion of bromine in potassium bromide may be used with equally good effect. The process is advantageously simplified by making a saturated solution of bromine in the concentrated alkali. This is done by pouring bromine into a solution of sodium hydrate, of the above given specific gravity, until no more is taken up, and then adding a little of the sodium hydrate solution until the liquid does not give off free bromine. The procedure with this solution is as follows: The pulverized mineral is moistened with, say, 10 cc. of the solution, and heated, then hydrochloric acid added to just acid reaction. Two more additions of the alkaline solution, in amounts of 20 cc. each, are added at intervals of about ten minutes, each addition being followed by hydrochloric acid. The total amount of the alkaline solution (containing the bromine) used is, therefore, 50 cc., and the amount of hydrochloric acid should not exceed that necessary to make the solu tion acid after each addition of the alkali. The mixture should be kept hot. After the final addition of acid, the contents of the beaker is taken to dryness and heated in an air-bath to 110° to 115°C., to render silica insoluble. The dry mass is then taken up by hydro' chloric acid and water and, after filtration, the sulphuric acid is pre

Jan 1, 1880

By W. Mont Ferry

It is impossible to speak in exact terms of the effect that selective flotation has had, is having, and may have on the State of Utah. Its results enter into the economic structure of the state in so many ways and its ramifications are so widespread, that every line of industry is affectcd. Some effects can be definitely determined; others can be reasonably approximated; but the effect as a whole can not be set out in exact figures. Utah is essentially a mining state; mining is its basic industry and always will be. Agriculture, equally a basic industry, and of course, equally vital, can be practiced on only 6 per cent. of the 85,000 square miles of its area. It follows, therefore, that the economic future of this state depends upon a development of its natural resources. About 6 or 7 years ago, the mining industry in Utah was at a low ebb. This condition was caused partly by postwar conditions and other temporary causes, but prevailed also, which was most important, because the direet-smelting ores of the state were being rapidly exhausted and the cost of treatment of complex ores was almost prohibitive. Furthermore, the wet concentration of low-grade ores was unsatisfactory and did not result in producing a good smelting product. On visualizing this situation, one of the large smelting companies in the valley had the courage, ability and faith to develop and expand the principles involved in selective flotation of complex ores. This example has been followrd by other smelting and reduction companirs and the result has changed the entire aspect of the mining industry in Utah. The utilization of the zinc in the low-grade, lead-zinc-silvrr ores was the principal prob1t.m to be solvcd. The average yearly production from the State of Utah for the 10 years beginning 1914 and ending 1923, was something less than 10,000 tons of zinc corlcentrates. This period includes the world war, when abnormal priccs stimulated production. In 1924, selective flotation began to be practiced on a considerable scale, replacing concentration by gravity and bulk flotation which had been used generally until this time. Production and Value of Zinc Concentrates The production of zinc concentrates during 1924 was approximately 24,000 tons, or twice the average yearly production of the previous 10

Jan 1, 1928

By T. W. Watson, D. R. Flynn

,Measurements are reported for the thermal conductivity of four heat-resistant alloys which were measured at the National Bureau of Standards. Data are given for two samples of AISI Type 316 stainless steel covering a combined temperature range from -150° to + 800°C. The thermal conductivities of three samples of AISI Type 347 were measured over the temperature range from -150° to +150C. Thermal conductivity values are given for Carpenter 20 stainless steel from 100" to 800" C. Data are given for Inconel 702, in both the solution-annealed and the age-hardened condition, over the temperature range from -150" to +800C. SINCE 1958 the National Bureau of Standards, at the request of other government agencies or private laboratories, has carried out measurements of the thermal conductivity of a number of metals and alloys. This paper presents available thermal conductivity data obtained in this way on samples of four heat-resistant alloys. The data presented for Carpenter 20* stainless steel are, to the best of our knowledge, the only thermal conductivity values which have been reported for this alloy to date. Although thermal conductivity values for AISI stainless steels 316 and 347 have been reported by previous investigators, the present data are believed to be of particular interest because, for each alloy, the effect on thermal conductivity of small changes in chemical composition can be observed. The data on Inconel 702' are of interest, not only for

Jan 1, 1969

Technology has no recognized rank in what is called polite literature; the subject-matter of engineering is not supposed to lend itself to artistic treatment; we are the hewers of wood and drawers of water to the high-priests of learning that live on the cold summit above our humbler dwellings. Therefore the hierophants smile at the notion of 'style'- “that curiously personal thing”--in technical writing. The "great art" of Pater, the "inevitable phrase" of Raleigh, the "note of distinction" that Arnold demanded are said to be beyond the scope, as they are supposed to be beside the need, of a writer on geology or engineering. This is a narrow view. Science, no less than belles lettres, calls for the best exercise of the human intelligence; the art of writing should be employed as skilfully and as earnestly in a description of the structure of the Sierra Nevada, or of the construction of a tunnel through the range, as in a rhapsody welcoming the rosy fingers of the dawn. The idea still lingers that fine writing does not befit technology, even though the masters of the Victorian period- Huxley, Tyndall, Ruskin-proved that science is worthy to be arrayed in the best robes that the looms of thought can weave. At the beginning of these lectures I quoted Barrie's remark touching the inability of the scientific man to express himself. That imputation has been passed to the technologist, whose utilitarian pursuits are supposed to make him too clumsy for the refinements of human speech. We may not have acquired the self-consciousness of those writers on Art whose "power of expression is so cultivated that their sensual caterwauling may be almost mistaken for the music of the spheres"; nor can we imitate the politicians, who have the ability to speak far beyond anything that they may have to say; but we too have a litera-

Jan 1, 1931

By A. Kavetsky, W. J. Whiten

Data from ball mills with a wide range of diameters are analyzed using detailed mathematical/ numerical models. Analysis shows the relative power inefficiency of large ball mills is due to their inefficient breakage of coarse particles. The models developed can be used to scale-up mill behavior. The behavior of large mills at Bougainville and Pinto Valley is compared. It is concluded that the mills are equally inefficient at grinding coarse particles. Differences in coarseness of total mill feed are shown to account for the fact that Pinto Valley mills achieved design throughput whereas Bougainville mills did not.

Jan 1, 1985

JOHN B. HASTINGS, Los Angeles, Cal. (written discussion *).-This, paper is so admirable for its brevity that one hesitates to enter into discussion. The cycle of eruptives makes one wonder, "Where's the basalt?" and the youthfulness of the Idaho flows suggests they may yet come. Veins and Dikes.-Veins and dikes seem to be closely aligned in the minds of some authors, while to me they appear quite distinct, the first representing quiet, long-continued action, typified by metasomatic replacement, far removed from volcanic action; the latter, sudden and cyclonic, emanating from the heart of vulcanism. The rock openings occupied by both types were formed by kindred forces, but in the one they were closed for indefinite periods before invasion by the solfataric solutions, and in the other their formation and occupation were simultaneous. Open Fissures.-I do not believe in the existence of open spaces of discission that may be occupied by veins. Occasionally they occur; I found one with. a machine drill 350 ft. below surface, fortunately in an adit; the water spouted for 12 ft. in a 6-in stream for nearly 24 hr. It was only a flattish fissure, 6 in. wide, crossing the perpendicular vein, and indicating how tabular veins of ore might be formed. The practical absence of open fissures should be a joy to miners. We all know the misgivings with which we feel about for an old winze having only 30 ft. of water in it, in an unsurveyed and inaccessible part of a mine. It is said that veins are sometimes formed in open spaces left by Protuberances of the walls, which meet after having been displaced; but I believe that in such circumstances there would be sufficient attrition and brecciated material to fill the fissure, though perhaps loosely. Parts of veins may possibly have been formed in originally open spaces, but if so, the spaces were made by solution shortly preceding the deposition of the veins. That total solution of rock adjacent to a fissure may occur under favorable conditions is proved by the existence of large bodies of sulphide which contain only a few per cent. of silica; while on the same level, and in other levels above and below, all being within the same ore shoot, assays may show as much as 50 to 60 per cent. of silica, although the gold, silver and copper assays may be almost identical in all the

Jan 1, 1918

Bellows Connector Fabricated of chemically inert Teflon, the new bellows type connector has many pipe line applications where vibration, expansion and electrolysis exist in the handling of corrosive liquids or gases and solvents. The new connector is electrically non-conductive, flexible even at 94°F and as strong as 480°F as at 70°F, according to the manufacturer. This bellows connector serves as a [ ] vibration dampener as well as an expansion joint and connects misaligned couplings and insulates flanges electrically. End flanges of the joint are French-type envelope gaskets made integral with the joint for easy assembly between companion flanges and a tight, leak-proof seal on installation. Circle No. 1

Jan 1, 1952

AN earthquake caused an upheaval in Japan, started fires which destroyed large parts of Tokio, Yokohama and Hakone, and with tidal waves and other consequences extinguished some 68,000 lives and much property right at the beginning of September." Also on Sept. 1, the Italians, offended by the murder of members of the Albanian frontier commission by Greeks, occupied the Island of Corfu, which was viewed as an act of war by Italy against Greece. An appeal by the Greeks to the League of Nations was flouted by the Italians. One of the consequences of these affairs was to throw discredit upon the League of Nations and to excite doubts whether it would be able to survive. On Sept. 19, Greece made the formal apology to the Allies collectively and following that the Italians with-drew from Corfu. During this month also the embroilment between Italy and Jugoslavia over the matter of Fiume came again into prominence. In Bulgaria there was a communist uprising which was promptly put down by the government. The whole country was put under martial law. On Sept. 13 there began a military revolution at Barcelona, in Spain. On Sept. 14 the king of Spain accepted the revolution and charged the leader with the formation of a new government. Cosgrave was reelected president of the Irish Free State, without there being any disorder. Great Britain paid the remainder of her silver debt to the United States, thus writing finis to the Pitman Act. The position of Germany went from bad to worse during September. The mark has become valueless and the business that is being conducted is largely on a gold basis once more, in terms of dollars and pounds sterling. Chancellor Stresseman announced Sept. 24 that the German government had decided to abandon pas-sive resistance to the French and Belgians immediately and unconditionally.

Jan 10, 1923

By Valentin R. Garfais

The world's petroleum production in 1928 is estimated at 1,322,896,-000 bbl., an increase of about 62,000,000 bbl. over 1927, as compared with an increase of over 133,000,000 bbl. in the previous year. The daily average was close to 3,600,000 bbl., of which the fields on the American continent produced about 84 per cent. The most important development during the year has been the partial success of the attempts to temporarily control production without appealing to legislation and, as a consequence, the increasing realization that, in order to reach a permanent cure for this situation, some form of legislation is necessary to' make possible the conservation of the oil supply and the stabilization of the industry. The importance of such a control over American production is not merely local but worldwide, as the American oil supply is now and for years to come will be the controlling factor of the industry. United States.—Production in the United States, which in 1927 increased about 15 per cent. over the previous year, remained practically stationary in 1928, the total being estimated at 902,000,000 bbl., or 68.2 per cent. of the world's output. This uniformity in production during the last two years was due primarily to the curtailment of output from wells already drilled, it being estimated that the available or shut-in production at the end of the year was close to 500,000 bbl. per day, or equivalent to the combined production of Venezuela and Russia, the countries ranking second and third. Venezuela.—With a production estimated at 106,000,000 bbl., Venezuela has trebled its output in the last three years. The increase in 1928 was 43,000,000 which placed this country as second in rank, a position which it should easily maintain for years to come. The output could have been considerably larger had not the oversupply in the United States made it advisable for Venezuelan operators to enter into tentative conservation agreements. Russia.—In Russia, production has doubled in the last five years, and reached a new peak in 1928 with an output estimated at 87,800,000 bbl., or an increase of 10,000,000 bbl. over the previous year. Difficul-

Jan 1, 1929

By J. Tarwater

The torsional testing of cylindrical medium-carbon steel specimens, heat treated to a high strength level, revealed a stress-strain relationship that was dependent on the direction of torsional plastic pre-strain. This Bauschinger effect was observed in prestrained specimens both with and without subsequent elevated-temperature strain aging. Yield stresses in strain-aged specimens exceeded those of simply prestrained specimens and the difference in stress was greater when the prestrain direction opposed the test direction. This behavior is discussed in terms of the classical dislocation pile-up using Cottrell's equation, A plastically prestrained strain-hardenable member, loaded in a direction opposite to the direction of prestrain, produces a stress-strain relationship differing appreciably from the curve representing reloading in the prestrain direction. This phenomenon, referred to as the Bauschinger effect, will be discussed in terms of the stress differences ob- served at a specified strain. The effect, dating back to the 1880's, was first attributed to grain boundary stresses. When later work revealed that the effect was also present in single crystals, revised theories attributed the diminished applied reverse stress to assistance from internal long-range stresses. These stresses have been associated with dislocation pile-ups or with dislocation arrays having analogous stress patterns. The stress patterns are subject to alteration by interaction with interstitial solute atoms and acceleration of the interaction may be accomplished with elevated-temperature strain aging. As discussed herein, the interaction showed a directional effect with regard to the applied stresses necessary for small plastic strains. Aside from the rigorous Bauschinger stress-strai relationship, which compares prestrained members, it is interesting to compare the stress-strain curve of a member being prestrained with that of a prestrained member being reverse loaded. For small strains which are a fraction of the prestrain deformation, the applied stresses of the reverse reloaded member are smaller. However, as the reverse strain approaches the prestrain value, the stresses approach equivalence. It has been reported1 that the stress required to return a prestrained specimen to its initial "zero" position generally exceeds the prestrain stress because of the work hardening occurring on potential slip systems during prestrain.

Jan 1, 1963

By E. H. Rose

The question is often pondered whether the flotation process is still an art or has become a science. The fact is that flotation is a science in so many variables that only art can blend them. It is demonstrable that no less than one hundred variables are involved in any flotation operation, most of them immeasurable on a routine basis. The behavior of every one of them is always governed by orderly and unchanging law, as no man can doubt. There is nothing truly indefinite about that behavior; the only indefiniteness is in our knowledge of it, either in general or from hour to hour in the circuit. In dealing with a simultaneous equation in, say, one hundred variables, all not only affecting the outcome to some degree but many influencing each other as well, it is small wonder that the mineral-dressing profession presents a case history of debate and controversial opinion. The statement of the subject of this symposium—a symposium on flotation machines—seems to delimit and define the matters to be considered and at least the general nature of the conclusions sought. Nevertheless, in such a meeting it is not possible to meditate upon all the variables that do in one way or another affect performance of flotation machines. To attempt it would be much like trying to operate a hundred-ring circus. Perverse variables being what they are, one could expect the elephant in ring 36 to squirt a trunkful of water at the tightrope performer in ring 37 to ruin that artist's act, just as our learning to depress pyrite in the early 1920's ruined the act of the formerly faithful old Callows. Honest Disagreements Selective flotation dates from 1922 or 1923, when several plants established their regular flotation operations on a selective basis. Since then, two decades of efforr have gone into the development of better and better flotation machines. Many have come and gone. The competition has simmered down to perhaps a dozen machines, each one of which is staunchly defended by some operators as being the best for their particular jobs, and as scornfully dismissed by at least a few others elsewhere as being positively the poorest for theirs. These disagreements are honest disagreements, honestly arrived at after plenty of sweat. In many a flotation plant, one machine has been tried out against another under conditions as fair as they could possibly be made. Sometimes the results are on a par but more often one machine shows a consistent and unmistakable margin of superiority over the other. In equally honest and enlightened tests, machine A may win over machine B in one place, and machine B over machine A by as great a margin in another. This paper purposes to identify some of the more prominent reasons why this is so,

Jan 1, 1947

By E. H. Rose

The question is often pondered whether the flotation process is still an art or has become a science. The fact is that flotation is a science in so many variables that only art can blend them. It is demonstrable that no less than one hundred variables are involved in any flotation operation, most of them immeasurable on a routine basis. The behavior of every one of them is always governed by orderly and unchanging law, as no man can doubt. There is nothing truly indefinite about that behavior; the only indefiniteness is in our knowledge of it, either in general or from hour to hour in the circuit. In dealing with a simultaneous equation in, say, one hundred variables, all not only affecting the outcome to some degree but many influencing each other as well, it is small wonder that the mineral-dressing profession presents a case history of debate and controversial opinion. The statement of the subject of this symposium—a symposium on flotation machines—seems to delimit and define the matters to be considered and at least the general nature of the conclusions sought. Nevertheless, in such a meeting it is not possible to meditate upon all the variables that do in one way or another affect performance of flotation machines. To attempt it would be much like trying to operate a hundred-ring circus. Perverse variables being what they are, one could expect the elephant in ring 36 to squirt a trunkful of water at the tightrope performer in ring 37 to ruin that artist's act, just as our learning to depress pyrite in the early 1920's ruined the act of the formerly faithful old Callows. Honest Disagreements Selective flotation dates from 1922 or 1923, when several plants established their regular flotation operations on a selective basis. Since then, two decades of efforr have gone into the development of better and better flotation machines. Many have come and gone. The competition has simmered down to perhaps a dozen machines, each one of which is staunchly defended by some operators as being the best for their particular jobs, and as scornfully dismissed by at least a few others elsewhere as being positively the poorest for theirs. These disagreements are honest disagreements, honestly arrived at after plenty of sweat. In many a flotation plant, one machine has been tried out against another under conditions as fair as they could possibly be made. Sometimes the results are on a par but more often one machine shows a consistent and unmistakable margin of superiority over the other. In equally honest and enlightened tests, machine A may win over machine B in one place, and machine B over machine A by as great a margin in another. This paper purposes to identify some of the more prominent reasons why this is so,

Jan 1, 1947

By Porter W. Shimer

As is well known, cast-iron borings are a mixture of small particles of iron with more or less of finely divided graphite, separated from thc surfaces of these small particles during the process of boring. The amount of graphite thus mechanically mixed is, in all cases, quite large enough to cause serious difficulty when the problem is to obtain an average sample of a given lot of borings for carbon determination. This difficulty arises from the necessity of obtaining a uniform mixture of the heavy and comparatively coarse borings with the finely divided and light graphite, and of removing a sample for analysis without disturbing the uniformity of this mixture. It was first sought to overcome this difficulty by having the horings made very fine, so that they might have more nearly the size of the particles of graphite. It was not practicable, however, to secure this uniformity of size, since much of the graphite is in the form of the finest dust. At all events, the duplicate determinations of rarbon in these fine borings, made with every precaution by combustion in oxygen, frequently showed differences too large to be accounted for in arty other way than by imperfect sampling. Very coarse borings were also tried with the idea that the graphite separated from these large and heavy pieces would perhaps be inappreciable ; but it was found that quite enough was separated to vitiate the results. Various methods of mixing were tried, both in the bottle and on glazed paper ; but in all these mixtures it mas found that duplicate samples seldom colitained the same proportion of the mechanically mixed graphite; and when they did, there could be no certainty that it was the true proportion. All this was shown many times over by the failure of duplicates to agree closely, the differencheing sometimes so much as 0.20 per cent. It was finally clear that nothing was to be hoped from these methods. Even if we could secure a perfect mixture containing in every part its due proportion of graphite, it would run a great risk of being destroyed the moment a spatula was inserted to remove a sample: for the least agitation causes some of the graphite to fall through between the coarser borings.

Jan 1, 1886

By Robert M. Dreyer

Although lateritic ore deposits are relatively flat-lying, surficial ore bodies, the evaluation of lateritic bauxite and nickel deposits is among the most difficult problems confronting an economic geologist. Laterite is a soil formed under tropical conditions resulting in the concentration, within the soil zone, of certain trivalent metals - principally iron and aluminum, but also, locally, nickel and manganese. The soil zone is divided into two parts: (a) the true soil or lateritic zone and (b) the zone of partially altered bed rock or saprolite. Whereas bauxite generally is confined to the lateritic zone, some nickel deposits occur in both the laterite and saprolite zones. The evaluation of bauxite and lateritic nickel deposits thus has both similarities and differences. These ores have been formed by supergene, soil-forming solutions moving downward through zones of widely varying permeability within the weathering rock. Because the permeability varies widely, both vertically and laterally. the extent of weathering may vary greatly within short distances. Because the weathering process varies widely, the degree of metal concentration may also vary widely. It is not at all uncommon for a laterite to change, within a few centimeters, from a virtually valueless rock to a high grade ore. Moreover, the depth of weathering, and hence the depth and form of the ore profile, vary greatly. Obviously, for this type of deposit, a few grab samples or a few drill holes are virtually worthless. The evaluation of such a deposit requires a sophisticated statistical study based on thousands of carefully selected samples. As a rule of thumb, the cost of evaluating a large bauxite or lateritic nickel deposit will be about one cent per ton of ore in the ground. Thus, the cost of evaluating a several hundred million ton deposit may be considerable. The following factors must be considered during the evaluation: Type of Sampling: The best and most reliable samples for the evaluation of lateritic ores are taken along large, vertical channels in hand-dug pits. Where labor costs are high, some form of drilling may be used in place of pitting, but it is always wise to choose a drilling procedure after checking drilling results against a series of pit channel samples. The drilling may not reproduce exactly the results from pit channel samples, but it may be possible to derive a constant correction factor. If the physical character of the laterite varies within the deposit, it may, of course, be necessary to change the type of drilling, the correction factor or both. In some areas, it has been found empirically that augers, chum drills, vacuum drills, rotary drills, or core drills yield satisfactory results. The problem is to find which drilling technique gives results most similar to channel samples through the heterogeneous sequence characterizing the laterite in a given area. In lateritic nickel deposits, the drilling characteristics of the lateritic and saprolitic portions of the deposit are very different. Within the saprolite, the major nickel values are commonly found in weathered zones within less altered boulders - a type of occurrence which makes sampling very difficult.

Jan 1, 1979

By G. C. Gardner

A new correlation of blast penetration in model and operating blast furnaces is presented which overcomes objections to prevzous correlations. It is shown that the tuyere diameter is only of small importance in determining the magnitude of the penetration. The data from operating furnaces correlate satisfactorily with the data from models whose cross section is a segment of a circle. A bubble-shaped gas space called a "raceway" normally exists in front of the nose of a blastfurnace tuyere. The periphery or "wall" of the raceway is well defined and is composed of densely packed charge particles. The blast. issuing as a jet from the tuyere, entrains gas from the raceway, in the usual manner of a jet, as it flows to the opposing wall. There it divides and flows back around the walls to be entrained once more. The blast must, of course, eventually leave the raceway and pass up through the charge column, but before it does it may, on the average, make several circuits of the kind described and in doing so it carries with it charge particles, which, because of their fast and circulating motion, suggested the name of "raceway". A fuller description of the raceway may be found elsewhere."' Here it is only necessary to mention, in addition, the measurement which characterizes its size. If an iron bar is pushed through the opened peepsight of a tuyere, .as far as it will go with ease, it will be stopped by the relatively impenetrable opposing raceway wall arid the distance that the bar has been pushed from the tuyere nose is called the "penetration". This measurement may be of practical importance and has; been the subject, with considerable success, of several attempts at correlation with other variables2-5 as stated in the next section. There is still, however, a serious objection to the most recent correlation,3 which is overcome by the correlation proposed in this paper. It will be shown that the objection is not trivial, in that the new correlation will attribute considerably different importance to the variables affecting the magnitude of the penetration. The data to be treated were made available by Wagstaff and are the same as those used in his correlation. They include measurements taken on small models, in which a cold air blast was used and no combustion occurred, and they also include data from operating blast furnaces at Wheeling and Fairless. The information from the blast furnaces will be shown to be in substantial agreement with those models whose plan views are segments of a circle and which are thus like segments of a blast furnace. First, Wagstaff's most recent correlation3 will be discussed and the objection will be given. Then the new correlation will be developed and its implications considered. CORRELATION OF J. B. WAGSTAFF Wagstaff's correlation is where and D — the penetration D,-the internal tuyere diameter V —the blast velocity in the tuyere

Jan 1, 1961

By Ernest Darby

IF the correct balance between fuel and air is maintained in an open-flame furnace,1 little chemical action may be expected between the products of combustion and the metal being melted. Physical changes in the metal are the object of the melting operation, and indirectly, under certain conditions, may be the cause of subsequent chemical actions. If sufficient heat has been introduced into the metal to bring about the change from the solid phase to the liquid phase, and still further from the liquid to the vapor phase, the metal vapor in all probability will be carried from the furnace by the exhaust and rapidly combined with the oxygen of the outside air. The charge being melted in the furnace may contain elements which are chemically inactive at normal temperatures but which will form compounds at the elevated temperatures of the metal bath, or even at a lower degree. Such indirect chemical actions are very confusing and often lead to incorrect conclusions regarding furnace atmospheres. In the open-flame furnaces used in the melting of bronze, the furnace atmosphere is spoken of as being either neutral, oxidizing or reducing in its effect upon the metal. A neutral atmosphere, as mentioned, is generally considered as the atmosphere of the furnace that will produce melted bronze, neither oxidized nor gassed. It is in effect an atmosphere which is not directly the cause of any chemical action. In such an atmosphere absolutely pure metals may be melted and poured without the absorption of gases or the formation of metallic oxide. The metal has undergone a simple, physical change.

Jan 1, 1930

By J. C. Bayles

THE most unsatisfactory occurrences in the experience of a manufacturer are those from which he suffers damage and learns nothing useful. That there are such incidents, and that they occur with annoying frequency, is unfortunately true. An accident which can be understood and explained always carries some consolation with it. However bad the copnsequencee, one finds comfort in reflecting that they might have been worse, and that the knowledge of how to avert a more disastrous calamity from the same cause is worth what it cost. But when an accident occurs, which remains unexplained after anxious days of investigation and sleepless nights of reflection, and which is as liable to occur twice or twenty times, as once, very little satisfaction of any kind can be extracted from it by the most philosophical victim. Three such incidents have come under my notice in one establishment. Fortunately none of them were attended with very serious consequences, as no one was hurt, and the damage to property was slight; but in each instance, loss of life and great destruction were escaped by so narrow a margin as to make them extremely disquieting. I have recorded them in the hope, that from the experience of others maybe gained what my own careful investigations have failed to reach-—satisfactory explanations. The first of these curious occurrences was the bunting of a 16-inch pipe carrying air under a compression of about 1 pound. The pipe was made of light galvanized iron with soldered seams. Into it a rotary fan-blower delivered air, and from it smaller pipes were carried to the furnaces. The blower was run continuously. Neither the main pipe nor its branches had any connection with the gas conduits. Both air- and gas-pipes delivered into the furnaces; but although the gas was under much higher compression than the air, there appeared to be no good reason why, having free escape in case of leakage, it should ever make its way back into the air-pipe. One warm afternoon in June the main air-pipe exploded with great vio-

Jan 1, 1891

By V. S. Tuman

In the first part of this paper, an estimate is made of the magnitude and extent of the thermal stresses which result from mud circulation. Our study is made for the period of relaxation, i.e., when the drilling operations are terminated and mud circulation is discontinued. In the second part, we have shown how the thermal stress can affect the wave propagation. An example is worked out for a Carbondale sandstone (Illinois basin). It is concluded that, in extreme cases when differential temperature is about 100°F, the travel time will be affected by about 2 microsec/ft. For more refined permeability studies, such corrections would be desirable. MAGNITUDE AND EXTENT OF THERMAL STRESSES RESULTING FROM MUD CIRCULATION When geological beds are penetrated by boreholes, it is observed that the formation temperatures increase with depth; however, the temperature profile varies considerably from place to place. During drilling operations, mud pumped from a pit at atmospheric temperature absorbs heat from the lower beds. As a result, the drilling fluid returning to the surface is at a higher temperature than the surrounding beds. The temperature gradient in a well depends on the rate of mud circulation and other factors; normally, this temperature gradient is smaller than the natural gradient in the formations. (See Fig. 1.) The temperature difference between the mud column and the surrounding beds gives rise to therma1 stresses (which are also important in the phenomenon of fracturing), and it is expected that they will affect the transit time of the sonic front in velocity logging.1 It is evident chat beds near the surface will undergo various cycles and will have a complicated dynamical and thermal-stress history. A limestone bed which is just penetrated will act as a source of heat, warming up the cold mud pumped down a few minutes earlier from the surface pit. The same limestone bed a week later will act as a sink, absorbing heat from the drilling mud which has already warmed up sufficiently to be at a higher temperature than the bed in question. No doubt a large section of the hole will undergo a heat treatment, which will make the calculation of the exact magnitude of the thermal stresses very difficult. In the solution of wellbore thermal equation, it is assumed that the rock around the wellbore is elastic and isotropic, and that the system is radially symmetrical. A complete dynamical solution of the thermal stresses set up at different horizons during the drilling operations would require a comprehensive history of the mud circulation, the surface temperature of the pit and the number of hours in which mud was not circulated. CONDUCTION OF HEAT AND THERMAL EQUATION OF STATE

By E. C. Wright, P. W. Mumma

This paper describes some properties of steels in the composition range 0.10 to 0.30 per cent carbon and 1 to 7 per cent chromium. It is well known that some steels of this type develop high tensile strengths upon receiving comparatively simple heat treatments, such as ordinary air cooling from appropriate temperatures, with or without subsequent tempering treatments. These high strengths are frequently associated with unusual toughness as measured by the Izod or Charpy impact test. The chromium content, in addition to imparting the above properties, enhances the resistance to corrosion and improves the strength and oxidation resistance at elevated temperatures. Moreover, these steels have good forging and fabricating properties, as evidenced by the fact that several thousand tons of seamless tubing have been made during the past five years from steels containing 0.10 to 0.25 per cent carbon and 5 per cent chromium. Composition and Properties of Materials Tested Twelve 15-lb. induction furnace heats of the compositions shown in Table 1 were prepared, using low-carbon open-hearth steel base melts

Jan 1, 1933