Search Documents

By Mack H. Shumate

1 Raw coal from Truax-Traer Coal Co.'s Burning Star Slope mine, Jackson County, Ill., is brought to the surface by the new 42-in. slope belt haulage conveyor at the rate of 850 tph. The loading system shown above employs four storage tracks, two tail tracks for loading, and four 25-hp hoists, operating in pairs, and coupled to two dolly cars to move the trains of cars through the tipple. The system has a capacity for loading 1800 tph. One operator is needed to load on each of two shifts. A third man working for a few hours on night shift sets up for the morning cycle. Railroad crews bring in empties placing them in the storage yard, twenty cars to the track. Trains of empties are pulled through to the tail track and loaded on the return; hoists at opposite ends pull the trains in each direction. [ ] 2 Pairs of hoist drums are interconnected electric- ally by a Trench lay cable buried between the tracks. When one hoist operates moving the cars, the tail hoist idles with brake released. The operator, situated in the tipple over the cars, views the storage yard at the end of the first shift (left). When returning loaded cars to yard, four or five cars are held on the dolly to couple the next string of empties. Empties are ready for loading on the tail track (right). Differing from a gravity system in which empty and load tracks are on a slight grade, this system is designed for 80 railroad cars for a two-shift operation and one rail service per day.

Jan 6, 1962

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board, the Institute itself has five major awards to make annually for excellence in technical papers, as follows: The Robert W. Hunt Medal, The Hadfield Prize, The J. E. Johnson Jr., Award, The Lewisohn Platinum Prize to senior members, and the President's Prize to junior members. ROBERT W. HUNT MEDAL The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes; first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to. a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A sub-committee of three to five including the Chairman of the Iron and Steel Committee, shall be appointed by the iron and Steel Committee annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the. award be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5. The recipient of the award shall be designated "The Hunt Medallist." SIR ROBERT HADFIELD PRIZE Sir Robert Hadfield has offered an Institute prize of $1000 for researches with regard to the different forms of combination of carbon in iron and steel. Until within a few weeks no paper has been submitted which could compete for this prize. If the paper in hand should not meet the requirements, the donor has suggested that the prize be transferred and offered for: (a) the determination of the hardness in metals in connection. with super-hardness, (b) in consideration of questions of fuel economy, (c) in consideration of questions of industrial development and labor. J. E. JOHNSON, JR. AWARD This award is made from the income of a fund of $3000 donated by Mrs. Margaret Hilles Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practise, vice-chairman of the Institute's Iron and Steel Committee, and a frequent contributor of papers to the Institute's TRANSACTIONS.

Jan 1, 1925

By G. C. Wallick, W. R. Foster, J. G. Savins

Inasmuch as the differentiation and integration methods represent different modes of rheological analyses, a dual scheme of analysis using both methods should lead to a generalized method of data analysis. A dual differentiation-integmtion method of analysis is applied here to the Poiseuille flow of a variety of ideal Generalized Newtonian and viscoplastic models. Using machine-processing techniques, the result is a spectrum of response patterns which are expressed in terms of certain derivative functions. It is shown that these characteristic functions form the basis of a highly-sensitive analytic technique for optimizing the selection of the most appropriate functional relationship between shear rate and shearing stress. INTRODUCTION In the first paper of this series, Savins, Wallick and Foster1 presented an historical review of the salient features of the differentiation method of rheological analysis in Poiseuille flow, and also indicated how the method could be applied to problems involving plane Poiseuille flow. It was shown that the differentiation and integration methods, although basically not incompatible, do represent different modes of rheological analysis. This suggests that valuable background information regarding the probable response characteristics of real data obtained with the differentiation method can be obtained from an integration method-differentiation method analysis of the response of a variety of ideal rheological models. The present paper describes how this dual method of analysis has been applied to suites of idealized models representing a wide variety of Generalized Newtonian and viscoplastic behavior which have received attention at various places in the literature.

By M. P. Nackowski, Armond H. Beers, W. T. Parry

Three hundred soil samples were collected on a one-mile grid in a 400-square mile area of the Oquirrh Mountains, Utah, including the Bingham-Lark, Ophir, Rush Valley, and Mercur mining districts. The soil samples were analyzed for copper, lead, zinc, silver, molybdenum, manganese, and iron by X-ray fluorescence using arsenic as an internal standard. Anomalies coincide in most cases with the mining districts. However, in the Mercur district no anomalies were detected. Also samples collected one mile from the Bingham mine barely reflect this major producer. No samples were collected within the Bingham mine area.

Jan 1, 1973

By P. E. Schauer

During the initial nine-year deple-tion of the McKamie-Patton pool gas-condensate reservoir, the pressure behavior and fluid analyses indicated pressure maintenance by gas injection would be attractive relative to continued pressure depletion. As a result, a gas cycling program was inaugurated in Aug., 1949, which has since maintained reservoir pressure. In order to evaluate the benefits of this program, the recoveries for natural depletion and for cycling followed by blowdown were determined by calculating the fractional balance of the molar quantities of vapor and liquid remaining in the reservoir and produced at the surface for various stages of depletion. The results of the investigation show theoretical ultimate recovery due to the cycling program will be 42 per cent greater than would be realized under pressure depletion type operation. INTRODUCTION The benefits of gas injection pressure maintenance programs in condensate reservoirs have been recognized and qualitatively described in several papers1-8 during the past 15 years. Some of these papers also describe methods for calculating the increased recovery realized from cycling; however, as a rule, hypothetical reservoirs were used as examples".'.. This paper presents an evaluation of the pressure maintenance program for the McKamie-Patton condensate reservoir and includes a description of the fractional balance method employed to determine the benefits. Reservoir Development and Characteristics The McKamie-Patton pool, Lafayette County, Ark., was opened in June, 1940, with production obtained from the oolitic Smackover lime at a depth of approximately 9,300 ft. The structure is an anticline 8 miles long by 1 to 2 miles wide, and is one of many productive Smackover structures in Southern Arkansas. Of predominant importance is the condensate-bearing gas cap portion of the reservoir, which covers approximately 4,000 acres, attains a maximum thickness of some 200 ft, and has an average thickness of 90 ft. Development of the cap was accomplished with 21 wells drilled on 160 acre spacing. An isopach map of the cap is shown in Fig. 1. In addition, an oil rim is present along most of the periphery of the pool. Production practice includes field separation of black oil, and a high pressure gathering system which carries total well stream from gas cap wells to a plant where condensate is separated and the gas is processed for recovery of natural gasoline, butane, and propane. Since the gas contains appreciable hydrogen sulfide, it is removed by amine contact, after which free sulfur is produced by the Claus process. Core analyses from 1,767 gas cap formation samples averaged 14.2 per cent porosity and 379 md dry air permeability. Connate water was restored on seven samples of gas cap rock by air-brine capillary techniques, from which the interpreted water saturation averaged 28.17 per cent. During the early life of the field, it was believed the recovery mechanism, based on several of the other regional Smackover reservoirs, might be a natural water drive. However, subsequent production and pressure history revealed that the gas cap would not be produced by water drive, but would behave as a closed reservoir. In this respect, during the nine-year period of natural depletion from initial production to Aug., 1949, the cap production of 84.3 billion

Jan 1, 1958

By D. L. Abata

This paper discusses recent technology dealing with the use of computer graphics in the mining industry. It presents a newly developed computer software package specifically designed for use in underground mining operations. This software package, developed under a US Bureau of Mines contract, 1) displays mine ventilation schematics and other representative illustrations for a real time data acquisition system and 2) uses the Bureau-owned Minefire and Ventilation Code for display of ventilation and contamination predictions on the microprocessor system. The package uses a unique system of display indexing that provides a simple yet efficient method of recalling a series of mine schematics detailing an underground operation and an alarm acknowledgment scheme that provides an effective method of identifying problem areas that may exist in the mine network. The package was written in Fortran for a 64-kilobyte, Z80-based microprocessor computer.

Jan 1, 1986

By C. L. Colburn

Discovery is the first step in the location of the claim. The provision of the Revised Statutes (2320) is, " No location of a mining claim shall be made until the discovery of the vein or lode within the limits of the claim located." Strictly speaking, discovery may be defined as the finding of ore or metalliferous rock in place in a well-defined vein. This definition was too strict, so discovery extended later to cover such indications of the pregence of ore, within rock in place, as would justify an experienced miner in spending his time and money with a reasonable expectation of finding ore in paying quantities. According to Colorado statutes a discovery must show a well-defined crevice; in Arizona, a lode, deposit, or mineral in place; in Montana, a well-defined crevice or valuable depositi; in Nevada, a lode or deposit of mineral in place. It is wrong to require a discovery. An honest prospector, wishing to obey the law, finds himself compelled, in most cases, to evade this point. In Clear Creek district, Colorado, a quartz seam will constitute a discovery; in Butte, a red capping; in Leadville or Ely, it is any place where a man can find a piece of vacant ground big enough upon which to sink a . 10-ft. hole. If the vein or deposit outcrops a man can show a discovery, but if it does not outcrop it is foolish to compel him to show one; and this point has been gently side-stepped. Any hole 10 ft. deep now constitutes a discovery. It is no use having laws that the people cannot consistently ob_ey. No sane man will dig unless he expects to find mineral, and he should be protected while digging. He should be required to show that he has mineral ground only when he comes to patent.

Jan 1, 1915

By W. G. Moffatt, J. Wulff

BRAZED joints and their strength have for some time been of great practical as well as theoretical interest. A good summary of the previous work in this field may be found in the reports of the Armour Research Foundation. In spite of excessive scatter in test data, the fact that the strength of a brazed joint may exceed the ultimate strength of the brazing material itself by many times continues to be of interest and of value in engineering. That this is qualitatively due to plastic constraint of the brazing material by the faying surfaces of the base metal is not in dispute, yet no complete interpretation of the data exists. The purpose of the present work is not to provide such a new interpretation, but to report new experimental data which we hope may lead to a better understanding of the important variables concerned. The work of Bredz' definitely shows that the thinner a brazed joint is, the greater is its strength. Dianeter of a joint has seldom been taken into

Jan 1, 1958

By W. G. Fischer, S. R. Felde

Trona ore at the Westvaco, Wyo., mine of FMC Corp. has been obtained by room-and-pillar methods since the mine began operation. The flat- lying, 10-ft thick trona (Na2CO3.NaHCO3.2H2O) is covered by 1500 ft of weak shale and sandstone, and extraction of pillars on the retreat quite often throws large amounts of weight onto development workings. Weak shales in the roof and floor fail rapidly, and the mine ribs slough to such an extent that mining often becomes very difficult. When this occurs, efficiency goes down, costs go up, and the risk to men and machinery increases greatly. Difficult mining conditions in the early '60s forced a re-evaluation of all presently known mining techniques in bedded deposits. Many room-and-pillar mining plans were compared with the system in use at that time, but none of them offered a better solution to the roof control problem. Longwall techniques were also seriously considered, but machinery was not available that would cut the hard trona seam and still maintain the productivity obtained from room-and-pillar sections. However, since roof control in the longwall methods appeared to be more satisfactory than that found in room-and-pillar techniques it was believed that a new technique using the longwall principle and based on rock mechanics should be tried rather than previously known pillaring methods.

Jan 4, 1966

By W. B. Tijmann

Maintaining safe, yet economical, slope geometries in a mining operation is paramount. When design analysis and engineering judgement have dictated conservative and usually more expensive problem solutions, monitoring has often proven to be a valuable method in dealing with potential slope instability. A well planned and executed monitoring program can allow operation at a lower theoretical margin of safety. Monitoring provides a valuable check on design parameters and can measure effects of remedial improvements. Warning of impending failure can often be established well in advance. The monitoring problem situations in civil engineering works and open pit mining are much alike. Instruments used for monitoring in both industries are often the same. In this paper, geotechnical instruments for measuring deformation and groundwater pressure in rock and overburden are discussed with a broad-brush approach. Results obtained over extended time periods are presented in a graphical presentation for a case history. Descriptions of various types of instruments, mostly used to monitor stability of rock slopes, are discussed, and data analysis and approximate costs are presented.

Jan 1, 1983

By F. Windolph

There are no hard and fast rules for building tailing dams, and each case has to be analyzed individually because of special conditions encountered at each location. Certain criteria are used for building dams at Climax, Colo., where they must be placed in rather steep mountain valleys on foundations that are practically impermeable. The tailing is relatively coarse, and a coarse fraction stays near the berm where it is deposited, while most of the fines flow with the water to the pool. Thirty years experience has led to certain design for toe dams, decanter lines and towers and tailing dams. A new tailing disposal area, started at Climax in 1958, will ultimately have a height of 495 ft and impound about 300 million tons. The following applies to the construction of this new tailing area.

Jan 11, 1961

By R. N. Lambert

This chapter discusses the evolution of high-speed shaft sinking in the South African goldfields. Whether we are talking of an additional shaft at an existing mine or the opening of a new mine, the increasing depth of the ore-bearing reef and the unremitting inflation of costs have provided the compelling incentive to shorten the time taken to sink a shaft and start earning revenue. The high costs of sinking a modern shaft system in South Africa are indicated by the recent example of a deep-level mine in the Orange Free State where the cost was nearly $22!42 million. This was for a single large shaft of 33 ft 6 in. diam (in all cases, shaft diameters refer to the finished diameter of the shaft, e.g., inside the concrete) and 7600 ft deep with a prestressed concrete brattice wall dividing the shaft into upcast and downcast compartments. Higher costs and the consequent demand for increased tonnages, deeper shafts with higher rock temperatures, which necessitate highly sophisticaled ventilation and refrigeration requirements, have all accentuated the importance of time in a shaft-sinking operation. Rectangular shafts with their simple design and comparatively reasonable sinking speeds remained popular for many years until greater mining depths combined with a host of the other allied problems inevitably led to changes in shaft design. Circular shafts appeared to offer many advantages, particularly when considering ventilation, strength, mechanization, and sinking through bad ground and heavily watered zones. However, these advantages were largely offset by the slow rate of advance necessitated by the need to stop sinking in order to line the shaft. The development of the curb ring which enabled lining to take place above the bottom of the shaft and the use of multideck stages allowing sinking and lining to be carried out concurrently resulted in a major break- through. Rectangular shafts, which are still popular elsewhere, have been superseded in South Africa by circular shafts which are almost without exception the only shafts sunk in our goldfields today.

Jan 1, 1970

By Joseph Pogue

OVER a period of years the writer has presented a number of studies1 on various aspects of proration, in a progressive attempt to analyze critically and constructively the economic complexities of this interesting institu-tion, which in a decade has revolutionized the economics of oil production in the United States. In the course of the investigations leading to these papers, the changing nature of proration and the principles under-lying its evolution have gradually become clear, so that it is now possible to depart from the analytical method and to construct a synthesis of the steps that, if furthered by the industry, should carry proration past the economic hazards that still surround it to the goal of maximizing the value of the petroleum resource to the industry and the public alike. NATURE OF PRORATION Proration literally means the allocation of demand among competing producers on a pro rata basis, but the term now carries a much broader significance for it is employed to describe the entire process by which the production of crude oil in the United States is regulated. There is naturally much confusion of thought on the subject, for proration is an evolving system of control based upon principles of conservation and equity and embracing a body of practices that are tending to adjust themselves to the needs of the situation but are subjected to varying and divergent influences in the process. As it is now constituted, proration is a planned production measure designed to prevent waste, insure ratable takings, and balance supply and demand. The procedure is administered by State regulatory bodies through use of the police power of the States under authority of State conservation laws; the practice is supported by a considerable degree of voluntary conformance on the part of operators; and the Federal Government has accorded its cooperation by providing advisory quotas, circumscribing imports, checking movements of hot

Jan 1, 1939

By A. J. Lynch, J. A. Holmes, F. C. Bond, D. W. Fuerstenau

This is an outstanding paper on comminution theory and represents a considerable advance in mathematical formulation. It clears the way for a discussion that should ultimately decide whether the work index should be considered as a parameter according to the Third Theory or as a constant. In the empirical differential equation dE = C dx/xn either C or n must be treated as a variable to satisfy known crushing and grinding conditions. The author has chosen the exponent n as the variable, with C as a constant.

Jan 4, 1958

By George M. Schwartz

WHEN reviewing the progress made in mining geology for the year 1953, one might say that not much has been accomplished and, indeed, in a subject such as economic geology not much progress should be expected in the 10 months of the year which elapsed before this article was prepared. This seeming lack of progress, however, disappears when the facts are investigated a bit. There undoubtedly are more economic geologists at work than ever before. It is probably not an exaggeration to say that more geologists are now employed by a single company in the Lake Superior district than were employed in the whole district 20 years ago. In most mining districts geologists are busy with numerous problems of production, development, and exploration and some give an occasional thought to the scientific problems of the science, or rather the art, of mining geology. In fact, this very intense activity of mining geologists is one reason why progress seems slow; they do not have time to write up results of investigations. There is also a great amount of work being done which is not released because of company policy. Conditions have improved very much in recent years but mining corporations, in general, have some distance to go before attaining par with the petroleum industry in this respect.

Jan 2, 1954

By S. Skowronski

PURPOSE OF INVESTIGATION Since cuprous chloride melts at 418° C., boils at 954° C. to 1033° C.,1 and is known to be volatile at a much lower temperature, the presence of chlorine in any form in or on copper to be melted has always been looked upon by copper refiners as a possible source of-serious copper loss. Although this fact has been known for some time, the copper literature contains little or no information regarding it and the field seems .never to have been properly investigated from a metallurgical standpoint. According to Greenawalt,2 cupric chloride, CuCl2, when ignited gives cuprous chloride; therefore cuprous chloride is always formed when copper enters into reaction with chlorine at a high temperature. Cuprous chloride melts somewhat below a dull red heat, and does not volatilize in closed vessels, even if strongly heated, but if heated in the air it goes off as a white vapor. Hofman3 gives the melting point of cuprous chloride

Jan 2, 1919

I. THE ENERGY CRISIS STILL EXISTS A. ALTHOUGH IMMEDIATE SHORTAGE IS NOW ALLEVIATED BY: 1. Increased imports through lifting of Arabian embargo; a. Imports were 6.5 million bpd during the week ended January 17, or 1.3 million bpd higher than last year. b. 1.7 million bpd higher than March '74. 2. Decreased demand resulting from higher prices and conservation. a. January 1975 demand was 17.9 million bpd, 0.1 million bpd lower than January 1973 and … b. 2.0 million bpd, or 10% under originally projected demands for January 1975. c. Gasoline (excluding tax) went up 59% from 27d/gal in August 1973 to 43c/gal in September 1974. d. Gasoline demand for January 1975 was 6.3 million bpd, 0.1 million bpd higher than 1973 but 0.7 million bpd ( 10% ) under projected demand. 3. Increased crude and major product inventories. a. January 17, 1975 crude and major product inventory was 794 million bbl, 99 million bbl higher than the same date in 1973. b. 105 million bbl increase since April 12, compared to only 38 million bbl increase during the same period in 1973.

Jan 5, 1975

By Joseph L. Mehaffey

A variety of chemicals offered by Armak were evaluated as dewatering aids for aqueous slurries of silica sand, sparsand and feldspar; an established commercial dewatering aid was used as a control. A number of Armak’s potential dewatering aids yielded lower moisture retention values than did the commercial product on all of the mineral samples. In addition to the chemical dewatering evaluations, some of the mechanisms involved in the removal of water from these mineral samples were examined.

Jan 1, 1984

By J. W. Putman, N. J. Grant, D. S. Bloom

SEVERAL recent determinations of the melting S point of pure chromium have been reported which give values of 1845°C1; 1895°C,² 1930°C,³ 1860°C,' and 1890°C.5 because of this wide spread of values, it appeared desirable to make one additional attempt to obtain a more accurate, reliable figure. bloom and Grantx recently reported a phase transformation in chromium:.--- it was desired to check this, too, in the course of checking the melting point. To accomplish this, a much higher purity chromium was required. Electrolytic chromium containing about 0.5 pct 0 was crushed to a finer size and was then annealed in highly purified, dried hydrogen at 1375°C for 100 hr. This treatment produced chromium with about 0.008 pct 0, 0.002 pct N, and negligible carbon. The balance of the impurities was 0.3 pct Fe, 0.03 pct Si, 0.004 pct S, and less than 0.001 pct Mo. This chromium was melted in a stabilized zirconia crucible under pre-purified argon, using induction heating. Temperature measurements were made with annealed wolfram-molybdenum thermocouples and a Leeds and Northrup Speedomax Recording Potentiometer. The thermocouples were annealed for 1 min in hydrogen at a temperature of about 2400°C. Each leg of the thermocouple was immersed in an ice-water mixture using mechanical connectors to the lead wires. The thermocouple tip was immersed in the molten chromium in a zirconia protection tube which introduces an error of about 3°C as a temperature drop through the walls of the tube. The weight of chromium was about 183 g. The dimensions of the melt in the crucible were about 1.25 in. diam x 2 in. high. The tip of the thermocouple was held about ½ in. from the bottom of the crucible. Two new thermocouples were used with the above set-up giving the results shown in Table I. Since this chromium is purer than that used by Greenaway, Johnstone and McQuillan,' by Carlile et al.,4 and other investigators,²,3 it is believed to be the more accurate. Thermocouple aging effects which are believed responsible for the high value of 1930°C³ were avoided in this work. This value of 1903°C is correct to about ±10°C. The right hand column lists the temperature of the a ? ß transformation on heating and the ß ? a on cooling.3 A sample curve is shown in Fig. 1. The value so determined is 1840°C + 15°C. Fig. 1 gives adequate evidence that there is a transformation in chromium at high temperatures.' References 'H. T. Greenaway, S. T. M. Johnstone, and M. K. McQuillan: High Temperature Thermal Analysis USing the Tungsten-Molybdenum Thermocouple. Journal Inst. Metals (November 1951) 19, p. 109. ²J. W. Putman, R. D. Potter, and N. J. Grant: The Ternary System Chromium-Molybdenum-Iron. Trans. A.S.M. (1951) 43, p. 824. ³D. S. Bloom and N. J. Grant: Chromium-Nickel Phase Diagram. Trans. AIME (1951) 191, p. 1009; Journal of Metals (November 1951). ' S. J. Carlile, J. W. Christian, and W. Hume-Rothery: The Equilibrium Diagram of the System Chromium-Manganese. Journal Inst. Metals (1949) 76, p. 169. 5G. Grube and R. Knabe: Ztsch. Elektrochemie (1936) 42, p. 793.

Jan 1, 1953

By John J. Childress, Russell L. Cook

Stringent environmental regulations, which have limited the use of sludge ponds, coupled with the economic incentive to clean more coal or to add fine coal cleaning additions to existing preparation plants have increased the use of static thickeners in preparation plants. The Lamella Gravity Settler, sometimes designated Lamella Thickener, is a shallow depth sedimentation device which has been applied in a variety of industrial process and wastewater control projects in place of the conventional raked thickeners. This paper presents the theory and design of the Lamella Thickener, as well as describing the operating results from several full scale installations in a variety of Appalachian preparation plants.

Jan 5, 1978