Search Documents

By G. G. Luther, C.E. Jackson

The relationship between hardenability and weldability has been mentioned many times. The ease of making a hardness survey has led to its wide use as a criterion of weldability and with a given class or series of steels for which the ductility under weld heat-treatment is known the test is entirely suitable. However, in studying a new steel the hardness survey is of less value, since it is based on the assumption that there is a correlation between hardness and ductility. Several attempts have been made to derive indices for weldabilityl and hardenability from the chemical analysis. In most of these proposals the effects of the different elements were considered to be additive, but recently Grossmann2 proposed a novel method of calculating the hardenability of a steel from its chemical composition. In the method proposed, a steel is considered as having a base hardenability due to its car- bon content and grain size, and this base hardenability is multiplied by a factor for each chemical element present. The final product is the hartlenability. The purpose of the present study is to point out the possible relationship between hardenability and the effect of welding on hardness and ductility for a number of plain carbon and low-alloy steels. The composition of the 25 steels reported in this paper as determined by chemical analysis is given in Table I. To eliminate the effect of variations in finishing temperatures, the 1/2-in. plates were normalized after heating for one hour at 1650°F. in a con-trolled-atmosphere furnace. In making comparative tests, it is essential to hold conditions as Constant as possible; hence full automatic weltling control was used. The electrodes, all supplied by

Jan 1, 1943

By G. G. Luther, C. E. Jackson

The relationship between hardenability and weldability has been mentioned many times. The ease of making a hardness survey has led to its wide use as a criterion of weldability and with a given class or series of steels for which the ductility under weld heat-treatment is known the test is entirely suitable. However, in studying a new steel the hardness survey is of less value, since it is based on the assumption that there is a correlation between hardness and ductility. Several attempts have been made to derive indices for weldabilityl and hardenability from the chemical analysis. In most of these proposals the effects of the different elements were considered to be additive, but recently Grossmann2 proposed a novel method of calculating the hardenability of a steel from its chemical composition. In the method proposed, a steel is considered as having a base hardenability due to its car- bon content and grain size, and this base hardenability is multiplied by a factor for each chemical element present. The final product is the hartlenability. The purpose of the present study is to point out the possible relationship between hardenability and the effect of welding on hardness and ductility for a number of plain carbon and low-alloy steels. The composition of the 25 steels reported in this paper as determined by chemical analysis is given in Table I. To eliminate the effect of variations in finishing temperatures, the 1/2-in. plates were normalized after heating for one hour at 1650°F. in a con-trolled-atmosphere furnace. In making comparative tests, it is essential to hold conditions as Constant as possible; hence full automatic weltling control was used. The electrodes, all supplied by

Jan 1, 1943

By Nathaniel Herz

The use of zinc dust for precipitating the pecious metals from cyanide solutions is well established now in many places, and has many advantages over the shavings method of precipitation. Although much work has been done o,n methods of testing zinc dust, as yet. no absolutely positive test has been devised to determine the value of the material. Certain facts are known, but often it happens that results on a working scale are not as expected from the laboratory tests. The purpose of this paper is to record some obscrvations made while testing a large variety of zinc-dust samples in the laboratory. W. J. Sharwoodl has described standard analytical methods, which have been followed, with the changes noted. The regular determinations include zinc oxide, by solution in ammonia and ammonium chloride, lead, and precipitating efficiency. In some cases cadmium was determined by a method similar to that described by J E Clennell.2 I will discuss the precipitating-efficiency test in detail. The procedure is as follows: "A solution of potassium silver cyanide is prepared by dissolving 10 grams of silver cyanide (AgCN) and 5 grams of 99 %' potassium cyanide in a little water and diluting up to 1000 cc. It is then adjusted by addition of a little more XCN or AgCN until the solution indicates from 0.12% to 0.15% free KCN by titration with standard silver nitrate. The titration is best made by using a 10-cc. or 20-cc. sample, adding 1 CC. of 2 % potassium iodide, and a slight excess of ammonia, as the end point is then sharper. Or 15 grams of pure crystallized XAg(CN)2 may be dissolved in a liter of water and 1.5 grams XCN added. " Weigh out 0.5 gram zinc dust into a 300-cc. beaker. Add a few cubic centimeters of watcr and stir until zinc is well mixed, then pour in 250 cc. of the prepared solution, stirring vigorously. See that all lumps are broken up, and continue stirring for fully five minutes. Stir occasionally (at least every 10 minutes) until the end of two hours from the addition of the solution. Then filter upon an 11-cm. filter, wash precipitate thoroughly, sprinkle with test lead, wrap it carefully in the paper, place in a scarifier with about 20 grams test lead, burn paper cautiously in muffle, scorify five minutes, cupel at low temperature and weigh silver. Milligrams silver obtained from 0.5 gram zinc X 0.0606 = percentage precipitating efflciency."³

Jan 1, 1916

By Paul M. Tyler

YEAR after year, the kaolin industry of the United States has been setting new production records and making better products. High-grade paper, pottery, and rubber clays are produced in this country mostly in the South. Georgia alone contributes over 70 pct and South Carolina almost 20 pct of the total domestic output. Residual kaolin is mined in North Carolina, highly plastic but naturally sandy Tertiary (Eocene) potting clays are worked in north central Florida, and good white clays are produced in several other states, but the main sources of kaolin or china clay have been numerous deposits in the Tuscaloosa (Upper Cretaceous) formation. This formation of generally sandy sediments is called the Middendorf member in older geologic reports and corresponds in age with some of the New Jersey clays. As shown in fig. 1, it crops out almost continuously in a generally southwesterly direction across South Carolina and Georgia and into Alabama. Clay is mined from this formation in all three states but the principal producing centers lie within about 10 miles of a straight line drawn between Aiken, S. C., and a point about 10 miles south of Macon, Ga. The white kaolins of the South were recognized and used prior to the Civil War but suitable treatment processes were not introduced until World War I when imports, chiefly from England, were curtailed. Although imports of high-grade clays were resumed after 1918, the domestic industry managed to treble its prewar production record during the early 1920's and has continued to grow. Whereas the 1909 to 1913 average total production in the United States was only 132,104 short tons valued at $705,352 f.o.b. mines, the output in 1948 was 1,568,848 tons worth $19,756,738.

Jan 6, 1950

By D. C. Bard

THESE notes are based on the megascopic study of a suite of 2,400 specimens of minerals and ores from the Butte mines, combined with field observations at intervals over a period of several years. The estimate of average vein composition is based on field acquaintance with the veins. It is probably correct in its broader proportions, and should be of use for comparison. Chemical and Mineral Composition of Butte Sulphide Vein. Matter. Per Cent. Oxygen 43.00-Quartz, rhodonite, rhodochrosite, barite, calcite, and hübnerite. Silicon 36.00-Quartz, rhodonite, and willemite (very rare). Sulphur 5.00-Sulphides of. iron, zinc, copper, lead,. and sulphates of barium and rarely calcium. Iron 5.00-Ferric sulphides (pyrite, bornite, chalcopyrite), also in sphalerite, tetrahedrite, and rarely hematite and siderite. Manganese, . . . . 2.00-Rhodonite, rhodochrosite, and hübnerite. Zinc, . . . . 1.00-Spha erite, very rare wurtzite and willemite, and tetrahedrite and tennantite.

Jan 8, 1913

By Charles E. Wait

The old laboratory at the School of Mines was among the notoriously bad ones, being situated in apartments of the main collegebuildings not originally intended, and conspicuously unfit, for the use to which they were put; while, as in many of our schools and colleges, the assaying was done in the basement of the college. Prominent among the disadvantages of such an arrangement are insufficient light, poor ventilation, and little or no provision to carry off offensive gases. It is not my intention now to present a complete description of this building. I wish merely to call attention to a few points in its construction and equipment, which may prove of interest to those who contemplate erecting buildings for snch work, and who may be, as we were in this instance, limited as to funds. In this laboratory every room is well lighted; all rooms used by students are well ventilated, and are provided with closed hoods for

Jan 1, 1887

By E. T. Dumble

(San Francisco Meeting, September, 1915) THE history of the several petroleum deposits of Texas and Mexico, or of the sediments in which they now occur, if the deposits are not indigenous to such sediments, is known in a general way only, but it nevertheless casts strong light on the conditions surrounding them and is of great importance in the search for and exploitation of then. The petroleum deposits of Texas are separable into two main divisions: 1. The deposits of northwestern Texas, which are directly connected with the Oklahoma fields to the north, and have no representatives at all in the Mexican area. 2. The deposits of the coastal area, which extend into Louisiana on the east and connect with those of the Mexican coast to the south. Early in the Pennsylvanian period a series of bituminous shales and limestones were laid crown over a broad area in Texas, Arkansas, and Oklahoma. These are known as the Bend series in Texas, the Caney shales in Oklahoma, and the Fayetteville beds in Arkansas. Following their deposition an uplift occurred, forming the Lampasas geanticlinal, which runs northeastward from the old Paleozoic land area of the Llano region toward Red River. The Bend series is petroliferous in places and has furnished a few producing wells on each side of the Lampasas uplift. This uplift forms the barrier and. dividing line between the two divisions of the Texas petroleum deposits. To the west of it, in waters which were the southern extension of the interior continental seas, in connection with the sediments and coal beds of the Pennsylvanian and Permian, great quantities of petroleum were deposited either as oil or as "potential petroleum." These sediments have been subject to very slight disturbance, and only very gentle folds. are found, with no signs of volcanic action in any part of the area. The conditions, therefore, indicate that the greater part, if not all, of the oil in this area is indigenous to the beds in which it is found.

Jan 8, 1915

The following list contains the names of members of whose deaths notices have been printed in MINING AND METALLURGY during the year ending April 1, 1939. Biographical sketches published in MINING AND METALLURGY are indicated in the last two columns.

Jan 1, 1944

By Courtenay de Kalb

The following observations upon onyx-marbles are fragmentary, and may shortly be rendered superfluous by the appearance of a work upon these interesting stones by Prof. George

Jan 1, 1896

By Ingersoll Olmsted

These ores are of two classes, Bessemer and non-Bessemer, existing in separate, though adjoining, beds. Both are carbonates, with small admixtures of oxides and other combinations. To prepare them for market they are roasted in kilns, which have already been described by Mr. John Birkinbine at the Troy Meeting, October, 1883 (Trans., xii., 378). Concerning their size, arrangement, etc., I need, therefore, only repeat that they are 60 feet in height; have wrought-iron shells 24 feet in diameter; are lined with fire-brick, and supported by cast-iron mantel and columns.

Jan 1, 1889

By T. H. Janes

NATURAL abrasives of some type are found in all countries of the world. In order of their hardness the principal natural abrasives are diamond, corundum, emery, and garnet, which are termed high grade, and the various forms of silica, including pumice, pumicite, ground feldspar, china clay and, most important, sandstone. The properties qualifying materials for use as abrasives are hardness, toughness, grain shape and size, character of fracture, and purity or uniformity. For manufacture of bonded grain abrasives such as grinding wheels, the stability of the abrasive and its bonding characteristics are also important. No single property is paramount for all uses. Extreme hardness and toughness are needed for some applications, as in diamonds for drill bits, while for other purposes the capacity of the abrasive to break down slowly under use and to develop fresh cutting edges is of greatest importance, as with garnet for sandpaper. In dentifrices, soaps, and metal polishes, of course, hardness and toughness are objectionable. First among the natural abrasives, industrial diamonds are essentially of three types: l—bort, which includes off-color, flawed, or broken fragments unsuitable for gems; 2—carbonado, or black diamond, a very hard and extremely tough aggregate of very small diamond crystals; and 3—ballas, a very hard, tough globular mass of diamond crystals radiating from a common center. Bort comes from all diamond-producing centers, carbonados only from Brazil, and ballas chiefly from Brazil, although a few of this last group come from South Africa. By far the largest producer of industrial diamonds is the Belgian Congo; the Gold Coast, Angola, the Union of South Africa, and Sierra Leone supply most of the remainder. There is no production in Canada, which imports $6 to $9 million worth of industrial diamonds annually. Industrial diamonds find innumerable uses in modern industry. They are used for diamond drill bits for the mining industry; in diamond dies for wire drawing; in diamond-tipped tools for truing abrasive wheels and for turning and boring hard rubber, fibers, and plastics; and in diamond-toothed saws for sawing stone, glass, and metals. High-speed tool steels, cemented carbides, and other hard, dense alloys can be cut, sharpened, or shaped efficiently only with diamond-tipped tools and diamond grinding wheels. .. Second only to the diamond in hardness is corundum, an impure form of the ruby and sapphire gems consisting of alumina and oxygen (Al²O³) with impurities such as silica and ferric oxide. Corundum generally crystallizes from magmas rich in alumina and deficient in silica, as in the nepheline syenites of eastern Ontario. Grain corundum is used in the manufacture of grinding wheels; very coarse grain is used in snagging wheels. Both types of wheels are employed in the metal trades, where the hardness of corundum, coupled with its characteristic fracturing into sharp cutting edges, makes it an ideal cutting tool. The finest corundum (flour grades) is used for fine grinding of glass and high-precision lenses. From 1900 to 1921 Canada was the world's leading producer of corundum. Following this period the deposits located in northern Transvaal of the Union of South Africa supplied more and more of the world's requirements, and since 1940 South Africa has provided almost the entire output, which has ranged between 2500 to 7000 tons a year during the last decade. Minor amounts have also been produced in Mozambique, India, and Nyassaland. Opportunities for Mining Corundum Corundum deposits in southeastern Ontario are of three types, which may be described as follows: 1—Scattered, irregularly-shaped deposits of coarse-grained corundum which could be mined by means of small pits. About 10 groups of such deposits are known. Although the tonnage of individual deposits of this type is not great, it has been estimated that several years' ore supply is available for a small tonnage operation. Deposits average about 9 pct corundum. 2—Large irregular deposits of coarse-grained corundum which would require mining by adit with possibly a scavenger operation on the remains of former surface deposits. The Craigmont deposit of this type produced about 20,000 tons of corundum concentrate during operations between 1900 and 1913. Most of the readily available surface ore was removed by operators during that time. Reserves of ore above road level have been estimated to average 7 pct corundum, but none of the so-called reserves have been blocked out, or even indicated, by diamond drilling. From 1944 to 1946, 2025 tons of

Jan 1, 1955

By F. C. Frischknecht

Most early development and application of electromagnetic prospecting methods took place in Scandinavia, where geological conditions favor their use. In other parts of the world these methods have aroused cycles of interest, but in Scandinavia they have been used continuously and successfully since the 1920's. Electromagnetic methods may be classified into two general groups. One group includes methods in which the source of the electromagnetic field remains stationary while the receivers are moved about to explore the area. The other includes procedures in which the energizing and receiving systems are moved together. Other classifications could be based on the size of the energizing source, the particular components of the electromagnetic field which are measured, or the mode of transporting the equipment. The difference between fixed-source and moving-source methods, however, is of such great fundamental importance that it will be emphasized in this discussion. FIXED-SOURCE METHODS Essentially, a fixed-source method consists of the measurement of electromagnetic fields about the source. The mutual coupling between the source and the earth is constant, but the mutual coupling between the receiver and the earth (unless the earth is homogeneous) and also between the source and the receiver changes at each station. The results are usually normalized by relating the field data to the calculated free space or primary field. Turam and Radio Reference Signal Methods: The turam or two-frame* (see Fig. 1A) is probably * Turam means two-coil. the most common fixed-source method. The energizing source is an insulated cable grounded at both ends or formed into a large rectangular loop. Measurements are taken along a traverse at 5 to 50-meter intervals using two small receiving coils, the lagging coil being placed at the position previously occupied by the leading coil. The complex ratio (i.e., inphase and out-of-phase ratios) of the voltages induced in the two coils is measured. Operating frequency range is about 100 to 800 cps. In a typical turam survey a straight, grounded cable several kilometers long is laid out parallel to the probable strike of the ore deposits or conducting strata being sought. An area extending 1 or 2 km on each side of the cable, and within 1 or 2 km of the ends of the cable, is surveyed. Measurements are made at stations 5 to 25 m apart along traverses perpendicular to the cable. Measurements may be made along lines parallel to the cable to serve as base lines for the traverses or for other special purposes. Commonly the receiving coils are oriented with their planes horizontal so that only the vertical component of the field is measured. If additional information is required, one of the hori- zontal components may also be measured by orienting the coils with their planes vertical. In a modified turam technique developed recently for both ground and airborne measurements (Fig. 1B) the amplitude of the complex voltage induced in a single receiving coil is measured and its phase compared with that of a reference signal transmitted from the energizing system by a radio frequency carrier. Thus the un-normalized field is obtained directly, whereas with the turam method it is obtained by calculation from the ratios. The turam method and its modifications have a greater working depth than the other electromagnetic procedures used in ore prospecting. Under favorable conditions conductors have been located at depths of 200 to 300 m. A modified turam method with one of the electrodes grounded in the upper end of a plunging orebody was used to follow the extension of this body to a depth of 200 m beneath a layer of conducting schists. Straight grounded cables are usually preferred to insulated loops because they are easier to lay out and because they often make the method more sensitive. The greater sensitivity of a grounded cable is a result of ground return currents which may flow in the orebodies in addition to the eddy currents caused by induction from the current in the cable. Anomalies in the vertical field due to eddy currents are characterized by a correspondence between high values for the inphase component and positive out-of-phase components and/or low values for the inphase component and negative out-of-phase components. Also the inphase component may approach zero, but it does not become negative. In very long continuous conductors that are parallel to a grounded cable the effect of ground return currents may far exceed the effect of eddy currents. These ground return currents cause a lack of correspondence between the inphase and out-of-phase components and may cause negative inphase or anti-phase components. It becomes difficult to carry out the measurements and often difficult to interpret the results. Such results immediately suggest the presence of graphitic strata, however, since ore deposits are rarely extensive enough to accumulate sufficient ground return current to cause these results. A cable laid out perpendicular to the strike or an insulated loop is sometimes used in areas where graphitic schists and slates are present. Anomalies are then completely or almost entirely due to eddy currents and are easier to interpret. The measured voltage ratios are normalized by either subtracting or dividing by normal field ratios calculated from free space considerations. The normalized ratios are then plotted as individual profiles. When significant anomalies occur in the ratio measurements, the actual normalized fields are calculated by beginning with a measured or an assumed value for the field at a point near the cable and successively multiplying this value by the normalized ratios. There is a similarity between this process and a numerical integration of the ratio curve. Conversely, in many respects the ratio curve is similar to the first derivative of the field curve.

Jan 1, 1960

By Charles M. Cooley

With explosives representing over 10 pct of the cost of operating the entire company, the Maumee Collieries Co., Terre Haute, Ind., inaugurated a program to develop a low-cost blasting agent. Results of more than two years' work were announced on May 1 by Hugh B. Lee, president of the company. Utilizing a mixture of commercial-grade ammonium nitrate and carbon black packed in polyethylene bags, Maumee has been able to reduce blasting costs by 50 pct. The lower costs are brought about principally by elimination of high transportation charges on fixed explosives and use of low-cost material (commercial NH,NO, and carbon black). The Akremite blasting method incorporates a 20-lb cap-sensitive primer to detonate the stable explosive. Maumee now uses Akremite exclusively in its stripping operations producing more than 2 million tons of coal per year. The explosive is employed to break about 25 million cu yd of overburden that covers the coal

Jan 5, 1955

By John Birkinbine

An unusually large number of crystals of magnetite obtained in the exploitation of a deposit of magnetic iron-ore of remarkable purity, encouraged the preparation of this paper, and its presentation at this time, that the matter might go on record in the Transactions. To make this record more complete, a preliminary statement is offered concerning the district and locality in which the ore is found. To the northeastern portion of the State of New York the United States is indebted for a large percentage of the iron-ore which has assisted in developing the resources and industries of the nation. As early as 1804, iron-ore was mined between Lake Champlain and the Adirondack mountains, and this district has since been an important and continuous contributor to our iron-ore supply. The production of the Lake Champlain district for the last, eleven years is as follows: Years. Gross tons. 1879,...........420,341 1880,...........531,000 1881,...........637,000 1882,...........675,000 1883,...........500,000 1884,...........504,894 1885,...........379,077 1886,...........588,752 1887,...........768,852 1888,...........789,419 1889,...........750,230 Approximate total,.....6,644,565

Jan 1, 1890

By Bernard York, John J. Reed

Mine opening stability was investigated by loading model openings to failure. Eight-inch plaster blocks were cast with small uniform section openings passing through the centers. After curing, the models were jacketed and loaded hydrostatically in a closed vessel. Opening size, shape, and orientation were varied to determine how these factors influence opening stability. THE investigation described in this paper is a continuation of a project begun in 1946 by Bernard York and W. E. Bush. .The experimental method used in the investigation involves the hydrostatic loading of a model mine opening to failure. Most investigators agree that this loading closely approaches actual conditions in very deep mines. The conditions are further idealized by using an essentially isotropic model material. The experiments consist of casting 8-in. plaster cubes, or 8-in. diam cylinders 8-in. long, having a relatively small uniform section hole passing through their centers. After thorough drying, the models are jacketed in a flexible plastic bag and loaded hydrostatically with water in a closed vessel. At about 300 to 500 lb per sq in. pressure the central opening fails. The fracture pattern resulting from opening failure is studied in a plane normal to the longitudinal axis of the opening. The model block is sawed through its center after loading to expose this plane and to eliminate the possibility of end effect. By changing

Jan 1, 1954

By B. B. Kunkle

The history of this refinery has been one of expansion. It now has the capacity to produce 240,000 tons of cathodes annually. A general flowsheet and descriptions of the plant layout, operations involved, and equipment used at one of the world's largest and most modern electrolytic copper refineries are presented. THE El Paso copper refinery of Phelps Dodge Refining Corp. was originally constructed by the Nichols Copper Co., in association with Phelps Dodge Corp. and the Calumet & Arizona Mining Co., in order to refine anode copper produced at the smelters of the two latter companies. Initial production was obtained from the plant in January 1930 and its annual refining capacity was 100,000 tons of anodes. In order to keep pace with Phelps Dodge Corp.'s increasing copper production in the Southwest, it became necessary in 1937 to increase the El Paso plant's refining capacity to 160,000 tons of cathodes annually. This was accomplished by adding two sections to the electrolytic tank house, increasing the number of anodes placed in each commercial electrolytic tank from 33 to 37, and making changes in the dc circuits which made it possible to put three generators on each of the two circuits instead of two, thus increasing the amperage on each circuit from 10,000 to 14,800 amp. The capacity of the two furnaces from which refined shapes were cast was increased by raising the sidedoor bays on the furnaces 6 in. An increase of 70 pct in the productive capacity of Phelps Dodge Corp.s Morenci Branch in 1942 again made it necessary to expand refining capacity. In order to accomplish this, Defense Plant Corp. set up a project to increase the capacity of the El Paso plant to 240,000 tons of cathodes annually. This project consisted of enlarging the tank house approximately 50 pct, the construction of another wire- bar furnace, and corresponding increases in other departments where necessary. The engineering work on this expansion was begun in March 1942. Actual construction was under way by August 1942, and the work was completed by March 1944. These additional facilities were purchased from Defense Plant Corp. by Phelps Dodge Refining Corp. in August 1949. The plant is in El Paso about eight miies east of the center of the city and near Highway 80 and the main lines of the Southern Pacific and Texas & New Orleans railroads. The plant site covers approximately 494 acres of company-owned land that is ideally adapted for its use, being well-drained sandy soil and having enough slope so that a minimum amount of excavation was required when the plant was constructed. There is still ample room on the plant site for any future plant expansion. The plant is constructed on four different ground levels and so arranged that the unrefined copper is unloaded on the highest level at the north side of the plant and the refined copper is shipped out from the lowest level on the south side of the plant. The receiving or unloading platform, weighing and sampling rooms, main floor of the tank house, acid and condensate storage tanks, and the slimes and copper sulphate plants are on the first or highest level. The tank house basement, yard scales, charging and furnace bays, balloon flue and stack, brick-storage building, substation and power house, boiler feedwater treating plant and pump house, water storage tanks, and change houses are on the second level. This second level also contains ample yard area for setting-up furnace charges, and for storage of custom scrap, cathodes, scrap anodes, blister, coke, and poles. The casting wheels, inspection conveyors, cathode shears, wire-bar scalping machine, slag

Jan 1, 1952

By Edward Keller

ALTHOUGH the subject matter contained in this paper is presented under a new title, its writing was induced by the work of S. Skowronski and K. W. McComas.1 A discussion of the latter is here combined with the presentation of new and independent data. The physical constants quoted by the authors of that paper, such as melting and boiling points, as also the chemical reactions of the substances involved, are so well established that the numerous confirmatory experiments and their application to metallurgical conditions leave little or no room for criticisms. On the contrary, they will greatly aid to dispel any lingering skepticism as to possible considerable losses of copper accruing when the metal is melted in the presence of its own and, probably, other chlorides and when no provision is made for the recovery of volatile products. Exception may be taken, to some degree, to that part of the work under the caption Melting Drillings of Copper Mixed With Sodium Chloride. These experiments should have been extended in order to make the implied reactions clear and the results convincing. The latter are stated to be, "that when sodium chloride is present above certain minimum quantity relative to copper some of it is found to volatilize in the melt while another part reacts with the metallic copper to produce the volatile cuprous chloride, and that When smaller quantities of sodium chloride are present the reaction is complete and all chlorine is found to have volatilized as cuprous chloride." Metallic copper and sodium chloride are mentioned as the sole reagents in this chemical process, acting, according to the authors, in a neutral atmosphere of carbon dioxide. The chemist, quite naturally, will inquire into the formula according to which that reaction takes place and find that it would present itself as follows: 2Cu + 2NaC1 = 2Na + Cu2Cl2 It would appear that the truth of this formula will be challenged and a more rational explanation of the reaction sought. Apparently, carbon dioxide is neutral relative to metallic copper in its molten state; whether it remains neutral in the presence of sodium chloride is quite another question. Does it not at that high temperature become an oxidizer and do not the conditions of the reaction change to those expressed in the following formula? 2Cu + 2NaCl + 2002 = Na2CO3 + CO + Cu2Cl2

Jan 9, 1919

By A. M. Hall

SULPHUR, even in small amounts, may often be harmful to nickel and high-nickel alloys, causing impairment of mechanical strength and destruction of malleability and ductility, as shown by Merica and Waltenberg.1,2 It may act. either in the form of nonmetallic inclusions produced in the liquid state during furnacing or as reaction products resulting from its diffusion into the solid metal. In recognizing the action of this element, ability to identify its various forms by means of the microscope is often of considerable importance, especially when direct quantitative methods are inapplicable. [ ] Of the sulphur compounds associated with nickel and high-nickel alloys, the sulphides that may be found in malleable nickel, Monel? and Inconel? are an important group. These sulphides were investigated by metallographic methods in order to provide descriptive data by which to identify them. The nominal compositions of malleable nickel, Monet and Inconel are given in Table I. The term "sulphide" is employed here in a very general sense, to designate a substance in which sulphur and one or more metallic elements are combined. The term includes any combinations of compounds and solid solutions. METHOD OF INVESTIGATION Three groups of small laboratory melts were made, one group to represent each of the three types of alloy under investigation. Within each group, a number of ingots with a sufficient variety of chemical analyses were prepared so that the effect of each of the elements entering the complete commercial alloy could be isolated and observed. In most cases, to facilitate metallographic study by exaggerating the number and size of the resulting sulphides, somewhat greater amounts of the minor elements were added than are present in the commercial alloys. Likewise, considerably more sulphur was added than is normal, but not enough to complicate the system. Transverse sections were cut at a point one third of the distance from the butt to the head of each ingot, polished and examined with an inverted stage metallograph equipped with a combination polarizing-analyzing vertical illuminator. The light source was a tungsten-mercury vapor arc lamp.

Jan 1, 1943

By W. A. Nordland

BISMUTH can be readily grown into single-crystal form using the so-called "quick freeze" growth method.' Some advantages of this method are that very large crystals can be grown in a relatively short time, and with comparatively simple apparatus. We have found the general quality of crystals grown by this method to be not as good as that of "pulled" crystals.' This communication describes a "quick-freeze"

Jan 1, 1968

By J. K. Buehler

With the rapid acceleration of the cost of shovel dippers and major standard shovel clipper rebuild components, maintenance management at Kennecott Copper Corp.'s Bingham Canyon mine initiated a dipper maintenance and rebuild program. The program focused on extending the service life of the shovel dipper, reducing field labor in maintaining dippers, and lowering shovel dipper rebuild costs. While comprehensive evaluation of the program is still underway, preliminary benefits of the program indicate: •Reduced field ,gelding for shovel dipper field maintenance, •Fewer dipper rebuild units entering the shop, and •Reduced dipper rebuild costs per unit.

Jan 1, 1979