Search Documents

By H. E. Mussey

When the American Institute of Mining Engineers visited the Birmingham district in May, 1888, the four Ensley furnaces (Fig. 1) then completed were referred to as monumental.' Their dimensions are givcn in Table 1. Mr. Gordon stated, with considerable satisfaction, that on the preceding day one furnace had produced 165 tons. The blast was

Jan 1, 1925

By C. G. Dunn, P. K. Koh

THE primary recrystallization texture in cold-rolled silicon iron, which is the matrix texture for developing the Goss texture or the cube-on-edge texture by secondary recrystallization at temperatures near 900°C,1-5,21 has not been adequately described. Thus from the present available information, it is not possible to explain satisfactorily both the grain-growth selectivity of the matrix and the often observed magnetic torque curve, which itself provides some information on the texture. Also lacking is information on the special annealing texture that develops in this material when the annealing temperature is 1200°C or higher and the rate of rise to temperature is extremely rapid. From the work of May and Turnbull5 and from unpublished work, it was known that isothermal annealing near 1200°C tends to reduce the extent of secondary recrystallization and that a much weaker cube-on-edge texture results if appreciable normal grain growth replaces secondary recrystallization. Koh and Dunn6,7 have obtained additional information on complex primary recrystallization textures from further studies made after normal grain growth. In these instances the initial textures were retained during normal grain growth. A similar result reasonably could be expected in the present study except for the presence of a grain growth ihibitor1-5,8,9.21 and its tendency to allow only a few grains to grow. However, any information on the orientations of grains in the special annealing texture, even if far from representative of the initial matrix texture, would provide useful information on the nature of the matrix texture. In the present texture study the method of Newkirk and Bruce,10 which is based on the methods of Geisler" and Schwartz, 12 is used to obtain a complete (110) pole figure of the primary recrystallization texture. The high-temperature annealing texture is determined simply from the orientations of a large number of selected grains. The kinetic nature of the process that produces the annealing texture is treated elsewhere13 and it is shown that a form of secondary recrystallization with a very high rate of nucleation occurs during rapid annealing at high temperatures. EXPERIMENTAL PROCEDURE Commercial 0.014-in. cold-rolled silicon iron strip (3.16 wt pct Si), prepared by two stages of cold rolling with an intermediate short anneal, was given a decarburizing 3-min anneal at 800°C. Me-tallographic studies indicated complete recrystallization. Short-time anneals at 900° C and at higher temperatures proved that secondary recrystallization had not begun at 800°C, in fact, the short additional anneals were still in the induction period of secondary recrystallization. A rapid rise to an annealing temperature of 1260°C (2300°F) was obtained in a BaC12and NaCl fused salt bath. The structures that resulted from anneals in the range 12- to 1000-sec duration were relatively finegrained, even though the growth was a form of exaggerated grain growth13 or secondary recrystallization with a high nucleation frequency.= Many of the grains were large enough for an X-ray study using a 5-mil X-ray beam. A transmission Laue Camera and an optical-mechanical stage for moving the grains into the X-ray beam were used. A total of 325 grains were X-rayed in this manner and the grain orientations determined. Complete (110) pole figures were obtained for the primary recrystallization texture using CoKa radiation at 30 kv in the back-reflection range, such as (220) for (110) poles, as described recently by Newkirk and Bruce.10 The low voltage serves to reduce the spurious white radiation to a minimum. A filter of 0.001-inch iron foil was located in front of the detector slit for transmission and in front of the beam slit for back reflection. A new and improved specimen holder extended the useful tilting angle range for transmission to 70 deg instead of 60 deg as previously reported.' A torque magnetometer was used to obtain the magnetic torque curves for a number of l-in. diam disk specimens. RESULTS The (110) pole figure of the material after recrystallization at 800°C is shown in Fig. 1. The positions of the pole concentrations are found to be

Jan 1, 1961

By M. J. Spendlove, H. W. St. Clair

An automatic surface-follower mechanism was used to measure the surface temperature and the rate of evaporation of molten zinc while undergoing distillation at low pressure. At pressures of 50 to 100 microns Hg, the rate of evaporation may be 60 to 80 pct of the theoretical maximum corresponding to the measured temperature. The rate decreases rapidly at pressures above 100 microns Hg, to only 7 pct of the theoretical maximum at 2000 microns Hg. Measured temperature gradients at the surface are in agreement with theoretical gradients calculated from the heat of vaporization, rate of evaporation, and thermal conductivity of molten zinc. THIS paper covers a series of careful measurements of the rate of evaporation of molten zinc at low pressures, undertaken as a part of a general investigation on the separation of metals by distillation.' Preliminary results on the rate of evaporation of zinc were described in a previous publication.' The results of the preliminary study are as follows: 1—The observed rates of evaporation of zinc were as high as 0.60 g per sq cm per min, corresponding to 75 pct of the maximum rate as determined by the temperature of the metal. 2—The evaporation rate was decreased from 0.30 g per sq cm per min at a pressure of 25 microns to only 0.09 g per sq cm per min when the pressure was increased to 5 mm. 3—The temperature of the surface during rapid evaporation may be 35" to 100°C less than the main mass of metal. Observed temperature gradients at the surface are consistent with those calculated from the heat of vaporization and the thermal conductivity of liquid zinc. In the preliminary experiments, the rate of evaporation was determined from the loss in weight of the metal in the crucible during the test. This was compared with the weight of the condensate. Obviously, this method was subject to error because of some uncertainty as to the period of evaporation that should correspond to the loss in weight. Furthermore, this method did not permit taking into account probable variations in the rate of evaporation during the test. A more serious shortcoming was that the temperature at the evaporating surface was not known, so the maximum theoretical rate of evaporation could not be calculated accurately. To improve the precision of rate measurements and to allow accurate measurements of the surface temperature, a refined experimental technique was developed whereby the temperature and position of the surface could be measured accurately. This was done by an automatic surface-follower mechanism that gave a continuous record of the surface temperature and the amount of zinc evaporated. These data permitted an instantaneous determination of the actual rate of evaporation and the surface temperature throughout the test. Pure zinc (99.99 pct Zn) was used in all experiments. Description of Distillation Furnace The details of construction of the distillation furnace are shown in Fig. l. The furnace is enclosed in a large quartz tube open at one end. The open end of the quartz tube is sealed by means of a water-cooled head. The entire enclosure is vacuum tight. The connection between the water-cooled head and the quartz tube is sealed by means of a rubber gasket which fits tightly against the smooth end of the tube. The metal is heated by induced current set up in the molten zinc and the walls of the graphite crucible by means of a water-cooled induction coil outside the quartz tube. High frequency current is passed through the induction coil from a 6 kw mer-

Jan 1, 1952

By P. E. Palmer, A. H. Daane, C. E. Habermann

Jan 1, 1965

By F. V. Tideswell

THE suggestion, which appears to find increasing favor, that the elementary composition of coals should be used as the basis of their classification, makes it important that our methods of expressing this elementary composition should be refined. It is doubtful whether many published ultimate analyses of coals are accurate within 1 per cent. carbon. Many are probably as much as 3 or 2 per cent. in error in carbon. It is, perhaps, not always realized that the extreme variation in carbon content over the range of bituminous coals is but 16 per cent. An error of 1 per cent. in carbon on analysis corresponds therefore with one-sixteenth of the whole range, an amount which is unjustifiable even for the application to commercial needs of a system of classification based on ultimate analysis. For the purposes of scientific research such limited accuracy is of little value. The object of this paper is to examine one important source of error in ultimate analysis, that due to the occurrence in coal of inorganic material, and to emphasize the need for the quantitative measurements (of carbon more particularly) on coals to be rendered independent of their contents of such material.

Jan 1, 1928

By R. W. Raymond

Jan 1, 1905

By P. L. Rittenhouse, M. L. Picklesimer

A rapid and seniquantitative method of determining prefered orientation on large numbers of. Zircaloy-2 specimens was desired. knoop microhardness measurerrzetzls were irvestigated as a solldtion to this pro6lem. The variation of Knoop microhardness measurerlerzts on selected planes as a function of 'irzdenle axis relutilje lo cryslallograplzic or fabrication divectals were used to corzstrrcl a polar coordinate hardness contour map. With use of an empirical relationslip between the single-crystal hardnesses and those of the polycrystalline material conentional pole figures could be constructed which compare favorably also obtained. To determine preferred oriention qualitatively from hardness data requires a minimum of twelve measurements per plane on three, preferattention to grain size, specimen prepartion, and in-rreinetzt, and analjlsis is of the order of- 45 to 60 rrin. THE design of structures from Zr alloys requires consideration of preferred orientation and the resulting anisotropy of mechanical properties. Rapid and semi-quantitative methods of evaluating anisotropy and of determining preferred orientation are needed for quality control and for examining the large number of test specimens required in development programs. The variation of Knoop microhardness with indenter orientation has been studied in single crystals of several hcp metals including titanium.' beryllium,' magneium, and zinc.4 The maximum hardness observed on any crystallographic plane other than the basal plane invariably occurred when the long axis of the Knoop indenter was either parallel or perpendicular to the projection of the [ OOOI.] direction on the plane of examination. When the major slip mode was (0001)(i2i0j the maximum hardness occurred at the parallel positio! but when the operating slip system was {10i0) (i210) the hardness was a maximum perpendicular to the [0001] projection. A minimum hardness was always observed at a rotation of 90 deg from the maximum. It follows that the orientation of the projection of the [0001] can be determined on any non-basal plane by making hardness measurements at a number of indenter orientations. The determination of the orientation of the [0001] projection on two non-parallel, preferably orthogonal, surfaces of the specimen will allow location of the [0001] direction in the specimen. It seems possible that such measurements could be used to examine, at least qualitatively, the preferred orientation existing in polycrystalline hcp materials. An investigation of the microhardness anisotropy in Zircaloy-2 was undertaken to ascertain whether these measurements could be used for this task. EXPERIMENTAL PROCEDURE Single crystals of Zircaloy-2 were grown by an a-8-a annealing sequence using electron-beam heating.= The orientation of the crystals was determined by a conventional back-reflection Laue technique. The crystals were then mounted on a goniometer head and the desired crystallographic faces were milled and chemically polished. Polycrystalline Zircaloy-2 specimens were prepared from fabricated sheets or plates. Inverse pole figures for these materials were obtained using the X-ray diffraction techniaue described by Jetter, McHargue, and illiams.' A Wolpert-Greis Micro-Reflex hardness-testing machine was used to make the Knoop microhardness measurements. The single-crystal and polycrystalline specimens were loaded to 0.5 and 2.0 kg, respectively. Determination of the scatter of hardness numbers as a function of applied load for several indenter orientations on several specimen surfaces showed that the loads selected were the lightest consistent with minimum scatter. Heavier loads did not appreciably decrease the scatter and produced hardness impressions too large to be conveniently measured with the equipment used. Seven crystallographic planes of the single crystals were examined, while six planes of examination were used in studying Zircaloy-2 polycrystals. The specimens were rotated 10 to 15 deg after each measurement and from four to eight impressions were made at each angle of rotation. RESULTS The two angles which were used to relate crystallographic directions and planes in the hcp cell to the planes of examination of the single crystals are shown in Fig. 1. 8 is the angle between the c axis. [0001]. and the normal, N, to the plane of examination. a is the angle between the long diagonal of the Knoop indenter and the projection of the c axis on the plane of examination. For exampIe, if P = 90 deg and a = 0 deg, the plane of examination is of the family

Jan 1, 1967

By H. C. Theuerer

EVEN the highest purity silicon available for semiconductor use contains significant amounts of donors and acceptors, usually aluminum, phosphorus, and boron. Aluminum and phosphorus can be removed from silicon by adaptations of the zone refining techniques' widely used with germanium. Removal of boron, however, has been a difficult problem. The approximate distribution coefficient for boron in silicon is 0.8, so that while zone refining is possible, it is not very effective in any reasonable number of passes. It has been found, however, that boron can be effectively removed from silicon by treatment of a liquid zone with hydrogen and water vapor. Starting with 40 ohm-cm, n-type silicon, use of zone refining coupled with hydrogen

Jan 1, 1957

By W. W. Wen, S. C. Sun

The objective of this investigation was to study the electrokinetic behavior of oxidized coals to indicate the feasibility of separating oxidized coals from ash materials and pyrite by an amine flotation process. The effects of soluble inorganic electrolyte products from coal oxidation were also examined. The electro-kinetic behavior of coals of different rank and degree of oxidation were studied by an electro-phoreses technique. Generally, increasing the oxidation increases the negative value of the zeta-potential and decreases the isoelectric point (IEP). Flotation results indicate that the flotation recovery increases with decreasing pH values, and that with ferrous sulfate at pH 6.5 the flotation recovery is optimum while the pyrite is depressed. Comparing the flotation results with the electokinetic results verified that in the presence of ferrous sulfate, the maximum hydro-phobicity of oxidized coal with dodecylamine and frother is near its IEP, which is around pH 6.5 to 7.0.

Jan 1, 1978

By George L. Heath

This paper is devoted chiefly to the coal-fields of the western part of the province of Chili and the eastern part of the province of Shansi; but the outline of this belt will give some idea of the extension of the coal-fields over northeastern China. This part of China is topographically divided into: (1) the mountainous peninsula of eastern Shantung; (2) the coastal plains, extending W. and SW. from the gulf of Pechili; and (3) the mountains and table-lands N. and W. of the coastal plains. The plains extend N. and W. from the gulf to within from 10 to 25 miles of the Great Wall, while their SW. extension covers western Shantung and reaches W. along the Yellow river almost to the southern boundary of Shansi. A line joining the mapped coal-fields, shown in Fig. 1, almost gives the western boundary of the plains; since these areas lie on the border of the plains—except the Tsê Chou field, which is on the table-land, 20 to 25 miles from that border. The coal-fields which have been mapped and investigated by the author are shown in Fig. 1. The one at and around Tongshan is known as the K'ai-p'ing coal-field; the one W. of Peking has been called the Wang-p'ing coal-basin; the one SW. of Pao-ting and N. of Chêng-ting may be called the Lingshan coal-field; and the one at and around Tsê Chou is known as the Tsê Chou coal-field. I. The K'ai-p'ing Coal-Field. As is shown in Fig. 2, most of this field lies in the coastal plains, and is therefore covered by alluvium and loess, which have buried the older rock-beds, and the more gentle and older topographic outlines, to such an extent that most of the re-

Jan 1, 1902

By Hans Neuberger

INTRODUCTION IN our everyday life, visual perception plays perhaps a more important role than any of the other senses with which we are equipped by nature. It is, therefore, quite understandable that the average person associates 'with the term "atmospheric pollution," clouds of dust, palls of smoke or deposits of soot, phenomena which are so familiar to the residents of industrial cities. On the other hand, "air" is usually considered the prototype of the invisible, of the intangible, and any suspensions in the air which do not conform to this concept, are regarded as foreign to the atmosphere and thus as "pollution." According to Webster, the term "pollution" implies uncleanness, impurity, in short, something undesirable. Although the scientist often accepts popular concepts, he is generally inclined to suspect that apparently "obvious" phenomena imply, literally, "more than meets the eye." To show that this suspicion is also justified with regard to atmospheric pollution, is the objective of this discussion. It will be shown that what seems foreign to the air at first sight, is by nature an integral part of it, and that the more important aspects of pollution generally escape attention. THE ATMOSPHERIC CONSTITUENTS We can distinguish two classes of atmospheric constituents: the permanent gases, chiefly nitrogen, oxygen, traces of argon, neon, and others, and the variable constituents which include water in its different states, carbon dioxide, ozone, and various suspensions, either in gaseous, liquid or solid form. These suspensions, known by the collective term "Aerosol,"20 will be considered in detail. DUST There are two general types of aerosols: the first type is represented by the socalled "neutral" particle 3, commonly known as dust and experienced by everyone, as it is the more conspicuous type of suspensions. . It often represents a special problem to the mining engineer, the mechanical engineer, the industrial engineer, and many other professional men. Dust consists of finely divided solids derived from weathering, drilling, handling and preparation of rocks and coal. Dust may also consist of organic or inorganic particles resulting from manufacture of a variety of products such as flour, rubber, lime and steel, from traffic on land be it on the highways, on rails or in city streets, from decomposed vegetation or from volcanic eruptions. Perhaps the most reviled member of this class of suspensions is the soot and fly ashes from coal fires and other combustion processes. The cosmic source of dust, namely the injection of meteoric matter into the atmosphere, is of minor significance because the concentration of particles is exceedingly small despite the relatively large mass of material invades the earth’s atmosphere from space

Jan 1, 1948

By J. F. Kemp

CONTENTS. [ ] INTRODUCTION. THE saying that " of all the known regions of the universe, the most unsafe to reason about is that which is under our feet,"* might well be the motto of the present paper, in view of the writer's profound appreciation of the difficulties and uncertainties of the subject. In such a field, the temptation is very strong to announce a probable proposition, and then to defend it with a loyalty insensibly graduating into partisanship. Conscious of this danger, the writer has endeavored to maintain an impartial and candid form of statement, though others may feel that he has not been wholly successful. The subject, as here considered, falls naturally into two di-

Jan 1, 1902

By R. W. Raymond

The death of the eldest of the honorary members of the Institute was not unexpected. Ritter von Tunner had never recovered from the effects of a paralytic stroke received in 1892, and when the same enemy struck again in February of this year the blow was plainly mortal. He passed away June 9th, gently and without pain. Thus ends a career of great distinction and fruitfulness, crowned with fame and love. This pioneer of the age of iron and steel had lived so long and wrought so much that the present generation could scarcely recall the whole category of his services. There can be no more appropriate use of the pages of these Transactions than to honor them with a record of such a life and work, for the inspiration of other lives to other labors. Peter Tunner was born May 10, 1809, near Peggau, in Styria.† In the same province, his grandfather, Josef Tunner, had purchased a primitive nail-forge and enlarged it to a ham

Jan 1, 1898

By M. King Hubbert

THE growth of human knowledge is an evolutionary process. His-torically our separate sciences came into existence as people became interested in various apparently unrelated domains of phenomena, and in this manner we acquired the sciences of physics, chemistry, astronomy, biology and geology. As various of these sciences became established, cognizance of them came to be taken by the universities and in this manner there arose the traditional departments of physics, astronomy, chemistry, biology and geology of our American universities. As there was no particular rationality in the boundaries separating the various sciences, in the university departments the jurisdiction of each has assumed quite arbitrary limits. In the domain of earth phenomena the first science to grow up was that of geology, which arose originally from the activities of the collectors of rocks, minerals and fossils. Thus geology evolved as a descriptive science dealing with directly observable terrestrial phenomena for which elementary rational explanations were offered. The traditional treat-ment of phenomena by the science of geology has rarely been with more than an elementary regard for the fact that these phenomena were also phenomena of physics and chemistry. Since the latter part of the nineteenth century, a new approach to terrestrial phenomena has been emerging and becoming of so great a significance that it can no longer be ignored. This approach has been made by people trained primarily in the sciences of physics and chemistry, who have investigated terrestrial phenomena as constituting phenomena of, their respective sciences. In this manner we have acquired the so-called "borderland sciences" of geophysics, the physics of the earth, and of geochemistry, the chemistry of the earth. Neither of these fields is new, having arisen chiefly at the hands of European investigators during the latter part of the nineteenth century. The European uni-versities have long since given official recognition at least to geophysics, by the establishment of departments or institutes of geophysics, which are on a par with ,the university departments of the other sciences.

Jan 1, 1938

By Lombard Squires, W. K. Lewis, W. I. Thompson

Clays consist predominantly of hydrated silicates of alumina. The formula is frequently assumed to be A1203 . 2Si02 . 2H20,'and certain of I. North Carolina. Low plasticity. 11. Same as I, after washing. Low plasticity. III. Tennessee. Good plasticity. IV. Pennsylvania flint fireclay. Low plasticity. V. Laredo, Texas. Very plastic. CaO/Na2O corrected for GO2. VI. San Antonio, Texas. Fine grained, highly plastic. Moisture and CO2 were determined together at 18.8 per cent. VII. Selected crude bentonite, California. " Data from R. Ries: Clays. John Wiley & Sons, New York, 1927. them undoubtedly have substantially this composition, but in general the ratio of silica to alumina is considerably higher. However, they always contain water of chemical constitution, as shown by Table 1.

Jan 1, 1935

By H. A. Wheeler

That lead and zinc deposits are the result of prolonged,, slow deposition is the idea of most students of ore deposits, and in many cases, where the ore-bearing solutions have been very weak or the precipitating conditions have been very feeble, the ore accumulations have undoubtedly taken a long period of time. As these two vital conditions have been subject to great variations in the different mining camps, the following example is highly interesting in showing that deposition can be very rapid under favorable conditions, geologically speaking, and also extremely recent. In fact, the writer is inclined to regard most, if not all, of the Mississippi Valley deposits of lead and zinc as probably being very young, at least not older than Tertiary, if not Quarternary, in age. The extensive Joplin lead and zinc district, in southwestern Missouri, which is about 60 years old and has numerous mines that were abandoned from 1 to 50 years ago, shows that the lead and zinc today are in an active condition of solution and redeposition, although these two metals occur in the predominant form of sulfides. The mine waters from the older and more or less abandoned portions of the district are frequently so acid, mainly from the oxidation of associated pyrite, as to necessitate the use of wooden pipes and pumps. The first boom in the Oklahoma zinc fields, which is the southwestern extension of the Joplin district, occurred when ore was accidentally struck in drilling a water well. Among the mines then opened up was the Mission mine, at Lincolnville, Ottawa County, Okla. This mine was opened in 1903 in lean "sheet ground," or a flat blanket formation of chert carrying disseminated zinc blende, or "jack," and galena. Theore-body was very free from iron pyrites and the concentrates were very high grade, the "mineral," or lead concentrates, assayed 80 to 85 per cent. lead and the jack, or sphalerite, assayed 60 to 65 per cent. zinc. The orebody was very shallow, occurring at a depth of 76 to 95 ft. (22 to 28 m.) and very wet, requiring three or four pumps to handle the water. The mine was operated until 1914, when it was closed by litigation and immediately filled with water. The second Oklahoma boom, five years ago, opened up the large, active camps of Picher, Tar River, and Century, which are located 2 to 5 mi. west of Lincolnville. They are considerably deeper, being farther down on the westwardly dipping monocline that emanates from the Ozark

Jan 1, 1920

Jan 1, 1957

By Sherwin F. Kelly, Bela Low, William B. Creagmile

Electrical methods and instruments for geophysical exploration have been almost exclusively applied, during these years of development of the art, by a few companies specializing in this field. The control of patents, the cost of the instruments and the general lack of published information on details of field procedure and office interpretation have given these owners a monopoly in carrying out electrical surveys. The development of the Megger Ground Tester1 seems likely to change this situation, and to enable mining engineers and geologists, without special training in geophysics, to carry out simple reconnaissance electrical surveys. Nevertheless, the need for such special training and experience in planning surveys and interpreting their results remains, and probably i always will remain, indispensable for a successful outcome. The unique thing about, the Megger Ground Tester, which gives rise to this hope for its general use, is its simplicity of operation. The four binding posts of the instrument are connected by insulated wires to four stakes driven into the ground at appropriate points. The crank of the Megger is then turned, and the resistance of the ground between the two inside stakes is read directly, in ohms, by the deflection of a pointer over a scale. The apparatus is shown in Fig. 1. Fundamentally, the principle of operation is that of determining the resistance of a four-terminal conductor, as applied by Frank Wenner to the measurement of earth resistivity. "A four-terminal conductor is a conductor provided with two terminals to which current leads may be connected and two terminals to which potential leads may be connected. The resistance of such a conductor is the difference in potential between the potential terminals divided by the current entering and leaving

Jan 1, 1932

By Clemens Jones

The difficulties attending the reduction of ferric sulphate in the determination of metallic iron by the method of Marguerite, are often serious, and affect time, patience and accuracy. They depend upon the condition and purity of the zinc used, the state of saturation of the solution, acidity, and temperature. D. J. Caruegie (Chem. News, lvii., No. 1481), says that ferric solutions are instantaneously reduced by the use of zinc-dust. But there are obvious objections to its employment in quantitative work. Dr.

Jan 1, 1889

By R. B. Schluter, M. M. Fine

The Bureau of Mines' Twin Cities Metallurgy Research Center has of late concerned itself with reduction-induration of iron ore. One development provided a flowsheet for the agglomeration of green concentrate pellets in a reducing atmosphere created by a solid reductant external to the agglomerate. The product pellets were well metallized and physically competent. Maximum recommended operating temperature was 2100º F. In these studies, it was observed that unflred iron ore pellets indurated in a bed of anthracite or certain lignite chars frequently acquired exceptional crushing strength. A diagnosis of the phenomenon revealed that sulfur in the fuel was the probable cause. Accordingly, a research program was established to test this premise and to put it to practical use. Gaseous reductants were employed initially because of the ease and accuracy with which they could be metered.

Jan 10, 1969